Cool coatings with premium heat-re�ective technology from KYNAR 500® ORHYLAR 5000®PRE-FINISHED STEELFLAT SHEETS AND COIL

COLOR SELECTION GUIDE FOR KYNAR & SMP

OTHER STANDARD METAL PRODUCTS

Cold Rolled Galvanized Galvanneal Electro Galvanized

Brushed Stainless #4 Stainless 2B Aluminum Aluminum Tread Bright

For a true color respresentation, please contact us for actual metal samples.

Other colors and thicknesses available upon request.

www.ofrmetals.com

Mansard Brown24, 26 gauge

Dark Bronze24, 26 gauge

Medium Bronze24, 26 gauge

Charcoal26 gauge only

Bone White24, 26 gauge

Product DescriptionFluropon® coatings are premium �uoropolymer coatings that support full strength Kynar 500® or Hylar 5000® paint system with resins and solar re�ective pigments to support cool technology. Fluropon® coatings provide outstanding protection against the e�ects of ultraviolet radiation resulting in excep-tional color retention, and resistance to chalking and chemical degradation.

InstallationFluropon® can be cut, formed, fabricated and attached using hand or power tools. Fabrication and installation shall be in accordance with project drawings and speci�cations and conform to accepted sheet metal practices and industry standards. Cutting edges should be kept sharp, clean and properly aligned. Exercise caution during fabrication and installation to avoid damage.

Protective �lm must be removed immediately after installation. Oil canning is not cause for rejection.

Color SamplesColors shown represent the actual colors as accurate as modern printing technology will permit. Free metal samples are avail-able upon request. Additional custom colors are also available upon request.

MaintenanceThe full strength Fluropon® coatings are �eld-proven, high performance exterior quality �nishes and do not require maintenance. If cleaning is desired use mild soap and water followed by a clean water rinse.

KYNAR 500 is a registered trademark of Arkema, Inc.HYLAR 5000 is a registered trademark of Solvay Solexis.FLUROPON® is a registered trademark of Valspar Colorado

BRIGHTON, CO OGDEN, UT 303.654.0300 801.399.5700

303.654.0404 Fax 801.399.5775 Fax

O’NEAL FLAT ROLLED METALS FACILITIES

Test ASTM No. Galvanized Steel and Galvalume®Valspar Properties:Weathering and

Accelerated Tests

LEGEND

KYNAR = KYNAR 500 /HYLAR 5000®

SMP = SILICONIZEDMODIFIED

POLYESTER

Accelerated Weathering ASTM D-3361 Hours: 1000 total(Dew Cycle Weatherometer) Chalk: Rating 8

Color: 5 E Hunter Units Max

QUV ASTM G-53 Hours: 3000 totalChalk: Rating 8Color: 5 E Hunter Units max

Salt Spray ASTM B-117 Hours: 1000Scribe: Rating 6, 1/16”Field: Rating 10; No Blisters

Humidity ASTM D-2247 Hours: 1000 *Rating: 10, No Blisters

Formability ASTM D-4145 2-T

Elongation over 1/8” ASTM D-522 No CrackingCylindrical Mandrel No Loss of Adhesion

Pencil Hardness ASTM D-3363 HB Min

Specular Gloss ASTM D-523 25-35 at 60o

Impact Resistance ASTM D-2794 2 x Metal Thickness in inch-lb.No Loss of Adhesion

Falling Sand ASTM D-968 65-85 L/mil

Flame Test ASTM E-84 Class A Coating

*Performance of G-90, Hot-Dipped Glavanized, Galvalume and other approved Zinc/Aluminum coated steel.

ASK ABOUTENERGY STAR

www.ofrmetals.com