Comfortand energysavings
2013 edition
3.3.3.5.3.b V11 PCO3 remote display RE type unit
A different c l imateEnvironmental control solutions
LocalControl box
E n e r g i eTr a n s f e r tThermique
ummary
A different climateEnvironmental control solutions
For CAREL control - Local communication for 1 to 31 units ...................................................... 05
Quick user guide ................................................................................................................................................... 07
V11 PCO3 remote displayRE type unit
5V11 PCO3 remote display - RE type unit - 08/2013 - 3.3.3.5.3.b
ETT may change equipment data & design without prior notice.
6 5 4 3 2 1 0
Unit tee
65
43
21
0
Un
it te
e
RJ12 wire
S90C
ON
N00
2
3 shielded pairs wire, 6 x 0.75 mm² LiY-CYMaxi. length: 200 meters
1 shielded pair wire, 2 x 0.75 mm² LiY-CY
Up to 31 units
S90
Remote display
Features > Units parameters remote display.> Change of setpoints, operating hours, clock, etc.> Faults display and acknowledgement.
Installation and connections > Front mounting on a 300 x 200 x 120 box
!
!
Linking cables shall be provided and installed between the unit and the remote display by the installer.
The V11 display cannot be installed with the previous range units.
For CAREL controlLocal communication for 1 to 31 unitsRE type unit - V11 version
6 V11 PCO3 remote display - RE type unit - 08/2013 - 3.3.3.5.3.b
ETT may change equipment data & design without prior notice.
on-offon
alarmala
enteren
Use of silicone keys- "ON/OFF" key:
Starts or stops the unit.The green LED is switched on to indicate if the unit is started.
- "UP ARROW" and "DOWN ARROW" keys:Permit controlling the display screens and modifying parameters values.
- "ALARM" key: 1st push: alarms display and stop of the buzzer.2nd push: activation of manual reset.
- "ENTER" key:
The yellow LED always switched on indicates that the unit is under voltage.
pCO3 remote display keys
Menunu
Setet
Helpelp
ONOFFONOFF
- Displays the values measured by probes as well as the hour and permits going back to the "MAIN" menu.
- Permits changing from one unit to another.
- Gives access to the "INPUTS/OUTPUTS" menu.Displays digital or analog inputs and outputs status.
- Gives access to the "CLOCK" menu.Clock display / settings.
- Gives access to the "SETPOINT" menu.For setpoints display, selection and settings.
- Gives access to the "OPERATING HOURS" menu.Operating days & weeks display / settings.
- Gives access to the "HELP" menu.Keys functions description.
- Permits unit restart during a set time.
- Gives access to the "MAINTENANCE" menu.Permits displaying equipments maintenance values (equipment operating hour and service meter reset), probes and sensors calibration and compressors blocking.
For CAREL controlLocal communication for 1 to 31 unitsRE type unit - V11 version
7V11 PCO3 remote display - RE type unit - 08/2013 - 3.3.3.5.3.b
ETT may change equipment data & design without prior notice.
- Press "SET";
- press the "ARROWS" to change setpoints (FCTX setpoint);
- press "ENTER";
- change the temperature using the "ARROWS";
- go back to the main menu by pressing "MENU".
- Press the key;
- press "ENTER";
- switch on the digital diary (Y) using the "ARROWS";- press the "ARROWS" to stop the forced march (N);
- choose a day using the "ARROWS";- after having selected the right day, check that the unit is activated for this day (Y).
The basic setting makes all days activated except Sunday.
You can now set-up operating hours
- Press "ENTER";
- press the "ARROWS
- press "ENTER" to change the minutes;- use the "ARROWS- if you do not want to program the 2nd slot, leave the start-up and stop hours on 00h00. On the contrary, if you
want to program it, use the above method;- use the above method for the other days that need to be changed.
- Press "CLOCK";
- press "ENTER";
- change the hour using the "ARROWS";- use the "ARROWS" to change the minutes;
- press "ENTER" to display the day;
- change the day using the "ARROWS". Use the "ARROWS" to change the date;
- go back to the main menu by pressing "MENU".
Setet
enteren
enteren
enteren
enteren
enteren
enteren
Menunu
Menunu
Changing setpoint temperature
Changing operating hours
Changing the hour
Quick user guideV11 version - RE type unit
8 V11 PCO3 remote display - RE type unit - 08/2013 - 3.3.3.5.3.b
ETT may change equipment data & design without prior notice.
Going back to the menu
Delay restart
Help
- Press several times the key.
- Press "ON-OFF".
- Press "MENU".
- Press the key.
- Press the key.
Menunu
ONOFFONOFF
Helpelp
on-offon
Changing unit
Starting-up or stopping the unit
Quick user guideV11 version - RE type unit
www.ett.fr
Comfortand energy savings
Des
ign:
ETT
- D
ocum
ent p
rinte
d b
y an
env
ironm
enta
lly fr
iend
ly p
rinte
r usin
g ve
geta
ble
base
d in
k on
PEF
C p
aper
cre
ated
from
sust
aina
bly-
man
aged
fore
st.
Route de Brest - CS 93002 - 29830 Ploudalmézeau - FrancePhone number: +33 (0)2 98 48 14 22 - Fax: +33 (0)2 98 48 09 12Export contact: +33 (0)2 98 48 00 70 - ETT Services: +33 (0)2 98 48 02 22
A different c l imateEnvironmental control solutions