5/26/2018 Commercial Gear Quick Reference
1/26
1300 HYDRAULICS Innisfail Branch Cairns Branch1300 493 728 07 4061 9700 07 4081 5400
1300 806 330 07 4061 9722 07 4033 2055
Email: [email protected] Website: www.cfphydraulics.com.au
COMMERCIAL GEARPUMPS & MOTORS
QUICK REFERENCE
CATALOGUE
5/26/2018 Commercial Gear Quick Reference
2/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B1 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
GEAR PUMPS & MOTORS
05 07 10 12 15 17 20 22 25 27 30
Gear Width 1/2" 3/4" 1 1.1/4 1.1/2 1.3/4 2 2.1/4 2.1/2 2.3/4 3
30/31 Housing Size (in) 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25
Housing Size (mm) 31.75 38.10 44.45 50.80 57.15 63.50 69.85 76.20 82.55
cc/rev 16.10 24.20 32.30 40.40 48.40 56.50 64.60 72.60 80.10
ci/rev 0.98 1.48 1.97 2.46 2.95 3.45 3.94 4.43 4.89
30 Pressure (psi) 2500 2500 2500 2500 2500 2250 2250 2000 2000
30 Pressure (bar) 172 172 172 172 172 155 155 138 138
31 Pressure (psi) 3000 3000 3000 3000 3000 2500 2500 2200 220031 Pressure (bar) 207 207 207 207 207 172 172 153 153
50/51 Housing Size (in) 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 3.25
Housing Size (mm) 31.75 38.10 44.45 50.80 57.15 63.50 69.85 76.20 82.55
cc/rev 20.90 31.30 41.80 52.20 62.70 73.10 83.60 94.00 104.50
ci/rev 1.28 1.91 2.55 3.18 3.83 4.46 5.10 5.74 6.38
50 Pressure (psi) 2500 2500 2500 2500 2500 2000 2000 2000 2000
50 Pressure (bar) 172 172 172 172 172 138 138 138 138
51 Pressure (psi) 3000 3000 3000 3000 3000 3000 2500 2500 2500
51 Pressure (bar) 207 207 207 207 207 207 172 172 172
75/76 Housing Size (in) 1.75 2.00 2.25 2.50 2.75 3.00 3.25 3.50 3.75 4.00
Housing Size (mm) 44.45 50.80 57.15 63.50 69.85 76.20 82.55 88.90 95.25 101.60
cc/rev 50.40 67.20 84.00 100.80 117.60 134.40 151.20 168.00 184.80 201.60
ci/rev 3.08 4.10 5.13 6.15 7.18 8.20 9.23 10.25 11.28 12.30
75 Pressure (psi) 2500 2500 2500 2500 2500 2500 2250 2250 2000 200075 Pressure (bar) 172 172 172 172 172 172 155 155 138 138
76 Pressure (psi) 3000 3000 3000 3000 3000 2500 2500 2500 2000 2000
76 Pressure (bar) 207 207 207 207 207 172 172 172 138 138
315 Housing Size (in) 0.90 1.14 1.40 1.64 1.90 2.14 2.40
Housing Size (mm) 22.86 28.96 35.56 41.66 48.26 54.36 60.96
cc/rev 10.20 15.20 20.30 25.40 30.50 35.60 40.60
ci/rev 0.62 0.93 1.24 1.55 1.86 2.17 2.48
Pressure (psi) 3500 3500 3500 3500 3300 2900 2500
Pressure (bar) 241 241 241 241 228 200 172
330 Housing Size (in) 1.00 1.25 1.50 1.75 2.00 2.25 2.50
Housing Size (mm) 25.40 31.75 38.10 44.45 50.80 57.15 63.50
cc/rev 16.10 24.20 32.30 40.40 48.40 56.50 64.60
ci/rev 0.98 1.48 1.97 2.46 2.95 3.45 3.94
Pressure (psi) 3500 3500 3500 3500 3500 3250 3000
Pressure (bar) 241 21 241 241 241 224 207
350 Housing Size (in) 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
Housing Size (mm) 25.4 31.75 38.10 44.45 50.80 57.15 63.50 69.85 76.20
cc/rev 20.90 31.30 41.80 52.20 62.70 73.10 83.60 94.00 104.50
ci/rev 1.28 1.91 2.55 3.18 3.83 4.46 5.10 5.74 6.38
Pressure (psi) 3500 3500 3500 3500 3500 3250 3000 2750 2500
Pressure (bar) 241 241 241 241 241 224 207 190 172
365 Housing Size (in) 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00
Housing Size (mm) 31.75 38.10 44.45 50.80 57.15 63.50 69.85 76.20
cc/rev 44.30 59.00 73.80 88.50 103.30 118.00 132.00 147.50
ci/rev 2.70 3.60 4.50 5.40 6.30 7.20 8.05 9.00
Pressure (psi) 3500 3500 3500 3500 3500 3500 3250 3000
Pressure (bar) 241 241 241 241 241 241 224 207
5/26/2018 Commercial Gear Quick Reference
3/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B2 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P30/50/75 SERIES CAST IRON GEAR PUMPS & MOTORS
30 SERIES 31 SERIES
Model Gear Size Model Gear Size
PGP 30 3/4"2 PGP 31 3/4"2
PGM 30 3/4"2 PGM 31 3/4"2
50 SERIES 51 SERIES
Model Gear Size Model Gear Size
PGP 50 3/4"2 1/2" PGP 51 3/4"2 1/2
PGM 50 3/4"2 1/2 PGM 51 3/4"2 1/2
75 SERIES 76 SERIES
Model Gear Size Model Gear Size
PGP 75 1 3 PGP 76 1 3
PGM 75 1"3 PGM 76 1 3
PGP 300 SERIES CAST IRON GEAR PUMPS & MOTORS
PUMPS MOTORS
Model Gear Size Model Gear Size
PGP 315 1/2"2 PGM 315 1/2"2
PGP 330 3/4"2 PGM 330 3/4"2
PGP 350 3/4"2 1/2" PGM 350 3/4"2 1/2"
PGP 365 3/4"2 1/2" PGM 365 3/4"2 1/2"
5/26/2018 Commercial Gear Quick Reference
4/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B3 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P30 GEAR PUMPS
SAE B 4 BOLT
Stock CodeDisplacement
cc/rev Shaft Rotation
Inlet Port
SAESplit Flange
Pressure Port
SAESplit Flange
Mount Shaft
SAE B 13 T Shaft
P30A 442 BE UF07 -2524.2
ClockwiseSAE SAE
SAE B 4 Bolt SAE B 13T
P30A 542 BE UF07 -25 Anti-clockwise
P30A 442 BE UJ10 -2532.3
ClockwiseSAE 1 SAE
P30A 542 BE UG10 -25 Anti-clockwise
P30A 442 BE UK12 -2540.4
ClockwiseSAE 1 SAE
P30A 542 BE UH12 -25 Anti-clockwise
P30A 442 BE UK15 -2548.4
ClockwiseSAE 1 SAE
P30A 542 BE UH15 -25 Anti-clockwise
P30A 442 BE UK17 -2556.5
ClockwiseSAE 1 SAE P30A 542 BE UH17 -25 Anti-clockwise
P30A 442 BE UK20 -2564.6
ClockwiseSAE 1 SAE
P30A 542 BE UH20 -25 Anti-clockwise
SAE BB 15T Shaft
P30A 442 BE UF07 -4324.2
ClockwiseSAE SAE
SAE B 4 Bolt SAE BB 15T
P30A 542 BE UF07 -43 Anti-clockwise
P30A 442 BE UJ10 -4332.3
ClockwiseSAE 1 SAE
P30A 542 BE UG10 -43 Anti-clockwise
P30A 442 BE UK12 -4340.4
ClockwiseSAE 1 SAE
P30A 542 BE UH12 -43 Anti-clockwise
P30A 442 BE UK15 -43
48.4
Clockwise
SAE 1 SAE P30A 542 BE UH15 -43 Anti-clockwise
P30A 442 BE UK17 -4356.5
ClockwiseSAE 1 SAE
P30A 542 BE UH17 -43 Anti-clockwise
P30A 442 BE UK20 -4364.6
ClockwiseSAE 1 SAE
P30A 542 BE UH20 -43 Anti-clockwise
1.00 Diameter Keyed Shaft
P30A 442 BE UF07 -6724.2
ClockwiseSAE SAE
SAE B 4 Bolt 1.00 Dia Keyed
P30A 542 BE UF07 -67 Anti-clockwise
P30A 442 BE UJ10 -6732.3
ClockwiseSAE 1 SAE
P30A 542 BE UG10 -67 Anti-clockwise
P30A 442 BE UK12 -67
40.4
Clockwise
SAE 1 SAE P30A 542 BE UH12 -67 Anti-clockwise
P30A 442 BE UK15 -6748.4
ClockwiseSAE 1 SAE
P30A 542 BE UH15 -67 Anti-clockwise
P30A 442 BE UK17 -6756.5
ClockwiseSAE 1 SAE
P30A 542 BE UH17 -67 Anti-clockwise
P30A 442 BE UK20 -6764.6
ClockwiseSAE 1 SAE
P30A 542 BE UH20 -67 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
5/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B4 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P30 GEAR PUMPS
SAE B 2 BOLT
Stock CodeDisplacement
cc/rev Shaft Rotation
Inlet Port
SAESplit Flange
Pressure Port
SAESplit Flange
Mount Shaft
SAE B 13T Shaft
P30A 497 BE UF07 -2524.2
ClockwiseSAE SAE
SAE B 2 Bolt SAE B 13T
P30A 597 BE UF07 -25 Anti-clockwise
P30A 497 BE UJ10 -2532.3
ClockwiseSAE 1 SAE
P30A 597 BE UG10 -25 Anti-clockwise
P30A 497 BE UK12 -2540.4
ClockwiseSAE 1 SAE
P30A 597 BE UH12 -25 Anti-clockwise
P30A 497 BE UK15 -2548.4
ClockwiseSAE 1 SAE
P30A 597 BE UH15 -25 Anti-clockwise
P30A 497 BE UK17 -2556.5
ClockwiseSAE 1 SAE P30A 597 BE UH17 -25 Anti-clockwise
P30A 497 BE UK20 -2564.6
ClockwiseSAE 1 SAE
P30A 597 BE UH20 -25 Anti-clockwise
SAE BB 15T Shaft
P30A 497 BE UF07 -4324.2
ClockwiseSAE SAE
SAE B 2 Bolt SAE BB 15T
P30A 597 BE UF07 -43 Anti-clockwise
P30A 497 BE UJ10 -4332.3
ClockwiseSAE 1 SAE
P30A 597 BE UG10 -43 Anti-clockwise
P30A 497 BE UK12 -4340.4
ClockwiseSAE 1 SAE
P30A 597 BE UH12 -43 Anti-clockwise
P30A 497 BE UK15 -43
48.4
Clockwise
SAE 1 SAE P30A 597 BE UH15 -43 Anti-clockwise
P30A 497 BE UK17 -4356.5
ClockwiseSAE 1 SAE
P30A 597 BE UH17 -43 Anti-clockwise
P30A 497 BE UK20 -4364.6
ClockwiseSAE 1 SAE
P30A 597 BE UH20 -43 Anti-clockwise
1.00 Diameter Keyed Shaft
P30A 497 BE UF07 -6724.2
ClockwiseSAE SAE
SAE B 2 Bolt 1.00 Dia Keyed
P30A 597 BE UF07 -67 Anti-clockwise
P30A 497 BE UJ10 -6732.3
ClockwiseSAE 1 SAE
P30A 597 BE UG10 -67 Anti-clockwise
P30A 497 BE UK12 -67
40.4
Clockwise
SAE 1 SAE P30A 597 BE UH12 -67 Anti-clockwise
P30A 497 BE UK15 -6748.4
ClockwiseSAE 1 SAE
P30A 597 BE UH15 -67 Anti-clockwise
P30A 497 BE UK17 -6756.5
ClockwiseSAE 1 SAE
P30A 597 BE UH17 -67 Anti-clockwise
P30A 497 BE UK20 -6764.6
ClockwiseSAE 1 SAE
P30A 597 BE UH20 -67 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
6/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B5 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
M30 GEAR MOTORS
SAE B 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE B 13T Shaft
M30A 842 BE EF07 -25 24.2
Bi-Rotational
SAE -12
SAE B 4 Bolt SAE B 13T
M30A 842 BE EF10 -25 32.3
M30A 842 BE EF12 -25 40.4
M30A 842 BE AF15 -25 48.4
SAE -16M30A 842 BE AF17 -25 56.5
M30A 842 BE AF20 -25 64.6
SAE BB 15T Shaft
M30A 842 BE EF07 -43 24.2
Bi-Rotational
SAE -12
SAE B 4 Bolt SAE BB 15T
M30A 842 BE EF10 -43 32.3
M30A 842 BE EF12 -43 40.4M30A 842 BE AF15 -43 48.4
SAE -16M30A 842 BE AF17 -43 56.5
M30A 842 BE AF20 -43 64.6
1.00 Diameter Keyed Shaft
M30A 842 BE EF07 -67 24.2
Bi-Rotational
SAE -12
SAE B 4 Bolt 1.00 Dia Keyed
M30A 842 BE EF10 -67 32.3
M30A 842 BE EF12 -67 40.4
M30A 842 BE AF15 -67 48.4
SAE -16M30A 842 BE AF17 -67 56.5
M30A 842 BE AF20 -67 64.6
SAE B 2 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE B 13T Shaft
M30A 897 BE EF07 -25 24.2
Bi-Rotational
SAE -12
SAE B 2 Bolt SAE B 13T
M30A 897 BE EF10 -25 32.3
M30A 897 BE EF12 -25 40.4
M30A 897 BE AF15 -25 48.4
SAE -16M30A 897 BE AF17 -25 56.5
M30A 897 BE AF20 -25 64.6
SAE BB 15T Shaft
M30A 897 BE EF07 -43 24.2
Bi-Rotational
SAE -12
SAE B 2 Bolt SAE BB 15T
M30A 897 BE EF10 -43 32.3
M30A 897 BE EF12 -43 40.4
M30A 897 BE AF15 -43 48.4
SAE -16M30A 897 BE AF17 -43 56.5
M30A 897 BE AF20 -43 64.6
1.00 Diameter Keyed Shaft
M30A 897 BE EF07 -67 24.2
Bi-Rotational
SAE -12
SAE B 2 Bolt 1.00 Dia Keyed
M30A 897 BE EF10 -67 32.3
M30A 897 BE EF12 -67 40.4
M30A 897 BE AF15 -67 48.4SAE -16M30A 897 BE AF17 -67 56.5
M30A 897 BE AF20 -67 64.6
5/26/2018 Commercial Gear Quick Reference
7/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B6 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P50 GEAR PUMPS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P50A 478 BEUF 07 -0731.3
ClockwiseSAE SAE
SAE C 4 Bolt SAE C 14T
P50A 578 BEUF 07 -07 Anti-clockwise
P50A 478 BE UJ10 -0741.8
ClockwiseSAE 1 SAE
P50A 578 BE UG10 -07 Anti-clockwise
P50A 478 BE OJ12 -0752.2
ClockwiseSAE 1 SAE 1
P50A 578 BE OG12 -07 Anti-clockwise
P50A 478 BE OK15 -0762.7
Clockwise
SAE 1 SAE 1
P50A 578 BE OH15 -07 Anti-clockwise
P50A 478 BE OK17 -0773.1
Clockwise
P50A 578 BE OH17 -07 Anti-clockwiseP50A 478 BE OK20 -07
83.6Clockwise
P50A 578 BE OH20 -07 Anti-clockwise
P50A 478 BE OK22 -0794
Clockwise
P50A 578 BE OH22 -07 Anti-clockwise
P50A 478 BE OK25 -07104.5
Clockwise
P50A 578 BE OH25 -07 Anti-clockwise
1.25 Keyed Shaft
P50A 478 BE UF07 -1131.3
ClockwiseSAE SAE
SAE C 4 Bolt1.25
Keyed
P50A 578 BE UF07 -11 Anti-clockwise
P50A 478 BE UJ10 -1141.8
ClockwiseSAE 1 SAE
P50A 578 BE UG10 -11 Anti-clockwise
P50A 478 BE OJ12 -1152.2
ClockwiseSAE 1 SAE 1
P50A 578 BE OG12 -11 Anti-clockwise
P50A 478 BE OK15 -1162.7
Clockwise
SAE 1 SAE 1
P50A 578 BE OH15 -11 Anti-clockwise
P50A 478 BE OK17 -1173.1
Clockwise
P50A 578 BE OH17 -11 Anti-clockwise
P50A 478 BE OK20 -1183.6
Clockwise
P50A 578 BE OH20 -11 Anti-clockwise
P50A 478 BE OK22 -1194
Clockwise
P50A 578 BE OH22 -11 Anti-clockwise
P50A 478 BE OK25 -11
104.5
Clockwise
P50A 578 BE OH25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
8/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B7 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P50 GEAR PUMPS
SAE C 2 BOLT
Stock CodeDisplacement
cc/rev Shaft Rotation
Inlet Port
SAESplit Flange
Pressure Port
SAESplit Flange
Mount Shaft
SAE C 14T Shaft
P50A 498 BE UF07 -0731.3
ClockwiseSAE SAE
SAE C 2 Bolt SAE C 14T
P50A 598 BE UF07 -07 Anti-clockwise
P50A 498 BE UJ10 -0741.8
ClockwiseSAE 1 SAE
P50A 598 BE UG10 -07 Anti-clockwise
P50A 498 BE OJ12 -0752.2
ClockwiseSAE 1 SAE 1
P50A 598 BE OG12 -07 Anti-clockwise
P50A 498 BE 15 -0762.7
Clockwise
SAE 1 SAE 1
P50A 598 BE 15 -07 Anti-clockwise
P50A 498 BE 17 -07
73.1
Clockwise
P50A 598 BE 17 -07 Anti-clockwise
P50A 498 BE 20 -0783.6
Clockwise
P50A 598 BE 20 -07 Anti-clockwise
P50A 498 BE 22 -0794
Clockwise
P50A 598 BE 22 -07 Anti-clockwise
P50A 498 BE 25 -07104.5
Clockwise
P50A 598 BE 25 -07 Anti-clockwise
1.25 Keyed Shaft
P50A 498 BE UF07 -1131.3
ClockwiseSAE SAE
SAE C 2 Bolt 1.25 Keyed
P50A 598 BE UF07 -11 Anti-clockwise
P50A 498 BE UJ10 -11
41.8
Clockwise
SAE 1 SAE P50A 598 BE UG10 -11 Anti-clockwise
P50A 498 BE OJ12 -1152.2
ClockwiseSAE 1 SAE 1
P50A 598 BE OG12 -11 Anti-clockwise
P50A 498 BE 15 -1162.7
Clockwise
SAE 1 SAE 1
P50A 598 BE 15 -11 Anti-clockwise
P50A 498 BE 17 -1173.1
Clockwise
P50A 598 BE 17 -11 Anti-clockwise
P50A 498 BE 20 -1183.6
Clockwise
P50A 598 BE 20 -11 Anti-clockwise
P50A 498 BE 22 -1194
Clockwise
P50A 598 BE 22 -11 Anti-clockwise
P50A 498 BE 25 -11104.5
Clockwise
P50A 598 BE 25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
9/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B8 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
M50 GEAR MOTORS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE C 14T Shaft
M50A 878 BE EF07 -07 31.3
Bi-Rotational
SAE -12
SAE C 4 Bolt SAE C 14T
M50A 878 BE EF10 -07 41.8
M50A 878 BE EF12 -07 52.2
M50A 878 BE AF15 -07 62.7
SAE -16
M50A 878 BE AF17 -07 73.1
M50A 878 BE AF20 -07 83.6
M50A 878 BE AF22 -07 94
M50A 878 BE AF25 -07 104.5
1.25 Keyed Shaft
M50A 878 BE EF07 -11 31.3
Bi-Rotational
SAE -12
SAE C 4 Bolt 1.25 Keyed
M50A 878 BE EF10 -11 41.8
M50A 878 BE EF12 -11 52.2
M50A 878 BE AF15 -11 62.7
SAE -16
M50A 878 BE AF17 -11 73.1
M50A 878 BE AF20 -11 83.6
M50A 878 BE AF22 -11 94
M50A 878 BE AF25 -11 104.5
SAE C 2 BOLT
Stock Code
Displacement
cc/rev Shaft Rotation
Ports
O-Ring Boss Mount Shaft
SAE C 14T Shaft
M50A 898 BE EF07 -07 31.3
Bi-Rotational
SAE -12
SAE C 2 Bolt SAE C 14T
M50A 898 BE EF10 -07 41.8
M50A 898 BE EF12 -07 52.2
M50A 898 BE AF15 -07 62.7
SAE -16
M50A 898 BE AF17 -07 73.1
M50A 898 BE AF20 -07 83.6
M50A 898 BE AF22 -07 94
M50A 898 BE AF25 -07 104.5
1.25 Keyed Shaft
M50A 898 BE EF07 -11 31.3
Bi-Rotational
SAE -12
SAE C 2 Bolt 1.25 Keyed
M50A 898 BE EF10 -11 41.8
M50A 898 BE EF12 -11 52.2
M50A 898 BE AF15 -11 62.7
SAE -16
M50A 898 BE AF17 -11 73.1
M50A 898 BE AF20 -11 83.6
M50A 898 BE AF22 -11 94
M50A 898 BE AF25 -11 104.5
5/26/2018 Commercial Gear Quick Reference
10/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B9 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P75 GEAR PUMPS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P75A 478 BE OJ10 -0767.2
Clockwise
SAE 1 SAE 1
SAE C 4 Bolt SAE C 14T
P75A 578 BE OG10 -07 Anti-clockwise
P75A 478 BE OJ12 -0784
Clockwise
P75A 578 BE OG12 -07 Anti-clockwise
P75A 478 BE OK15 -07100.8
Clockwise
SAE 1 SAE 1
P75A 578 BE OH15 -07 Anti-clockwise
P75A 478 BE OK17 -07117.6
Clockwise
P75A 578 BE OH17 -07 Anti-clockwise
P75A 478 BE OK20 -07134.4
Clockwise
P75A 578 BE OH20 -07 Anti-clockwiseP75A 478 BE OQ22 -07
151.2Clockwise
SAE 2 SAE 1 P75A 578 BE ON22 -07 Anti-clockwise
P75A 478 BE OQ25 -07168
Clockwise
P75A 578 BE ON25 -07 Anti-clockwise
1.25 Keyed Shaft
P75A 478 BE OJ10 -1167.2
Clockwise
SAE 1 SAE 1
SAE C 4 Bolt1.25
Keyed
P75A 578 BE OG10 -11 Anti-clockwise
P75A 478 BE OJ12 -1184
Clockwise
P75A 578 BE OG12 -11 Anti-clockwise
P75A 478 BE OK15 -11100.8
Clockwise
SAE 1 SAE 1
P75A 578 BE OH15 -11 Anti-clockwise
P75A 478 BE OK17 -11117.6
Clockwise
P75A 578 BE OH17 -11 Anti-clockwise
P75A 478 BE OK20 -11134.4
Clockwise
P75A 578 BE OJ20 -11 Anti-clockwise
P75A 478 BE OQ22 -11151.2
Clockwise
SAE 2 SAE 1 P75A 578 BE ON22 -11 Anti-clockwise
P75A 478 BE OQ25 -11168
Clockwise
P75A 578 BE ON25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
11/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B10 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P75 GEAR PUMPS
SAE C 2 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P75A 498 BE OJ10 -0767.2
Clockwise
SAE 1 SAE 1
SAE C 2 Bolt SAE C 14T
P75A 598 BE OG10 -07 Anti-clockwise
P75A 498 BE OJ12 -0784
Clockwise
P75A 598 BE OG12 -07 Anti-clockwise
P75A 498 BE OK15 -07100.8
Clockwise
SAE 1 SAE 1
P75A 598 BE OH15 -07 Anti-clockwise
P75A 498 BE OK17 -07117.6
Clockwise
P75A 598 BE OH17 -07 Anti-clockwise
P75A 498 BE OK20 -07134.4
Clockwise
P75A 598 BE OH20 -07 Anti-clockwiseP75A 498 BE OQ22 -07
151.2Clockwise
SAE 2 SAE 1 P75A 598 BE ON22 -07 Anti-clockwise
P75A 498 BE OQ25 -07168
Clockwise
P75A 598 BE ON25 -07 Anti-clockwise
1.25 Keyed Shaft
P75A 498 BE OJ10 -1167.2
Clockwise
SAE 1 SAE 1
SAE C 2 Bolt1.25
Keyed
P75A 598 BE OG10 -11 Anti-clockwise
P75A 498 BE OJ12 -1184
Clockwise
P75A 598 BE OG12 -11 Anti-clockwise
P75A 498 BE OK15 -11100.8
Clockwise
SAE 1 SAE 1
P75A 598 BE OH15 -11 Anti-clockwise
P75A 498 BE OK17 -11117.6
Clockwise
P75A 598 BE OH17 -11 Anti-clockwise
P75A 498 BE OK20 -11134.4
Clockwise
P75A 598 BE OH20 -11 Anti-clockwise
P75A 498 BE OQ22 -11151.2
Clockwise
SAE 2 SAE 1 P75A 598 BE ON22 -11 Anti-clockwise
P75A 498 BE OQ25 -11168
Clockwise
P75A 598 BE ON25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
12/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B11 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
M75 GEAR MOTORS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE C 14T Shaft
M75A 878 BE AF07 -07 50.4
Bi-Rotational
SAE -16
SAE C 4 Bolt SAE C 14T
M75A 878 BE AF10 -07 67.2 SAE -16
M75A 878 BE AF12 -07 84 SAE -16
M75A 878 BE AF15 -07 100.8 SAE -16
M75A 878 BE AL17 -07 117.6 SAE -20
M75A 878 BE AL20 -07 134.4 SAE -20
M75A 878 BE AL22 -07 151.2 SAE -20
M75A 878 BE AL25 -07 168 SAE -20
1.25 Keyed Shaft
M75A 878 BE AF07 -11 50.4
Bi-Rotational
SAE -16
SAE C 4 Bolt 1.25 Keyed
M75A 878 BE AF10 -11 67.2 SAE -16
M75A 878 BE AF12 -11 84 SAE -16
M75A 878 BE AF15 -11 100.8 SAE -16
M75A 878 BE AL17 -11 117.6 SAE -20
M75A 878 BE AL20 -11 134.4 SAE -20
M75A 878 BE AL22 -11 151.2 SAE -20
M75A 878 BE AL25 -11 168 SAE -20
SAE C 2 BOLT
Stock CodeDisplacement
cc/rev Shaft RotationPorts
O-Ring Boss Mount Shaft
SAE C 14T Shaft
M75A 878 BE AF07 -07 50.4
Bi-Rotational
SAE -16
SAE C 2 Bolt SAE C 14T
M75A 878 BE AF10 -07 67.2 SAE -16
M75A 878 BE AF12 -07 84 SAE -16
M75A 878 BE AF15 -07 100.8 SAE -16
M75A 878 BE AL17 -07 117.6 SAE -20
M75A 878 BE AL20 -07 134.4 SAE -20
M75A 878 BE AL22 -07 151.2 SAE -20
M75A 878 BE AL25 -07 168 SAE -20
1.25 Keyed Shaft
M75A 878 BE AF07 -11 50.4
Bi-Rotational
SAE -16
SAE C 2 Bolt 1.25 Keyed
M75A 878 BE AF10 -11 67.2 SAE -16
M75A 878 BE AF12 -11 84 SAE -16
M75A 878 BE AF15 -11 100.8 SAE -16
M75A 878 BE AL17 -11 117.6 SAE -20
M75A 878 BE AL20 -11 134.4 SAE -20
M75A 878 BE AL22 -11 151.2 SAE -20
M75A 878 BE AL25 -11 168 SAE -20
5/26/2018 Commercial Gear Quick Reference
13/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B12 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P330 GEAR PUMPS
SAE B 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE B 13T Shaft
P330A 442 EK AB07 -2524.2
Clockwise
SAE 1 SAE 1 SAE B 4 Bolt SAE B 13T
P330A 542 KE AB07 -25 Anti-clockwise
P330A 442 EK AB10 -2532.3
Clockwise
P330A 542 KE AB10 -25 Anti-clockwise
P330A 442 EK AB12 -2540.4
Clockwise
P330A 542 KE AB12 -25 Anti-clockwise
P330A 442 EK AB15 -2548.4
Clockwise
P330A 542 KE AB15 -25 Anti-clockwise
P330A 442 EK AB17 -2556.5
Clockwise
P330A 542 KE AB17 -25 Anti-clockwiseP330A 442 EK AB20 -25
64.6Clockwise
P330A 542 KE AB20 -25 Anti-clockwise
SAE BB 15T Shaft
P330A 442 EK AB07 -4324.2
Clockwise
SAE 1 SAE 1 SAE B 4 Bolt SAE BB 15T
P330A 542 KE AB07 -43 Anti-clockwise
P330A 442 EK AB10 -4332.3
Clockwise
P330A 542 KE AB10 -43 Anti-clockwise
P330A 442 EK AB12 -4340.4
Clockwise
P330A 542 KE AB12 -43 Anti-clockwise
P330A 442 EK AB15 -4348.4
Clockwise
P330A 542 KE AB15 -43 Anti-clockwise
P330A 442 EK AB17 -4356.5
Clockwise
P330A 542 KE AB17 -43 Anti-clockwise
P330A 442 EK AB20 -4364.6
Clockwise
P330A 542 KE AB20 -43 Anti-clockwise
1.00 Diameter Keyed Shaft
P330A 442 EK AB07 -6724.2
Clockwise
SAE 1 SAE 1 SAE B 4 Bolt
1.00 Dia
Keyed
P330A 542 KE AB07 -67 Anti-clockwise
P330A 442 EK AB10 -6732.3
Clockwise
P330A 542 KE AB10 -67 Anti-clockwise
P330A 442 EK AB12 -6740.4
Clockwise
P330A 542 KE AB12 -67 Anti-clockwise
P330A 442 EK AB15 -6748.4
Clockwise
P330A 542 KE AB15 -67 Anti-clockwise
P330A 442 EK AB17 -6756.5
Clockwise
P330A 542 KE AB17 -67 Anti-clockwise
P330A 442 EK AB20 -6764.6
Clockwise
P330A 542 KE AB20 -67 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
14/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B13 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P330 GEAR PUMPS
SAE B 2 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE B 13T Shaft
P330A 497 EK AB07 -2524.2
Clockwise
SAE 1 SAE 1 SAE B 2 Bolt SAE B 13T
P330A 597 KE AB07 -25 Anti-clockwise
P330A 497 EK AB10 -2532.3
Clockwise
P330A 597 KE AB10 -25 Anti-clockwise
P330A 497 EK AB12 -2540.4
Clockwise
P330A 597 KE AB12 -25 Anti-clockwise
P330A 497 EK AB15 -2548.4
Clockwise
P330A 597 KE AB15 -25 Anti-clockwise
P330A 497 EK AB17 -2556.5
Clockwise
P330A 597 KE AB17 -25 Anti-clockwiseP330A 497 EK AB20 -25
64.6Clockwise
P330A 597 KE AB20 -25 Anti-clockwise
SAE BB 15T Shaft
P330A 497 EK AB07 -4324.2
Clockwise
SAE 1 SAE 1 SAE B 2 Bolt SAE BB 15T
P330A 597 KE AB07 -43 Anti-clockwise
P330A 497 EK AB10 -4332.3
Clockwise
P330A 597 KE AB10 -43 Anti-clockwise
P330A 497 EK AB12 -4340.4
Clockwise
P330A 597 KE AB12 -43 Anti-clockwise
P330A 497 EK AB15 -4348.4
Clockwise
P330A 597 KE AB15 -43 Anti-clockwise
P330A 497 EK AB17 -4356.5
Clockwise
P330A 597 KE AB17 -43 Anti-clockwise
P330A 497 EK AB20 -4364.6
Clockwise
P330A 597 KE AB20 -43 Anti-clockwise
1.00 Diameter Keyed Shaft
P330A 497 EK AB07 -6724.2
Clockwise
SAE 1 SAE 1 SAE B 2 Bolt
1.00 Dia
Keyed
P330A 597 KE AB07 -67 Anti-clockwise
P330A 497 EK AB10 -6732.3
Clockwise
P330A 597 KE AB10 -67 Anti-clockwise
P330A 497 EK AB12 -6740.4
Clockwise
P330A 597 KE AB12 -67 Anti-clockwise
P330A 497 EK AB15 -6748.4
Clockwise
P330A 597 KE AB15 -67 Anti-clockwise
P330A 497 EK AB17 -6756.5
Clockwise
P330A 597 KE AB17 -67 Anti-clockwise
P330A 497 EK AB20 -6764.6
Clockwise
P330A 597 KE AB20 -67 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
15/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B14 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
M330 GEAR MOTORS
SAE B 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount
Shaft
O-Ring BossSAE B 13T Shaft
M330A 842 VR EB07 -25 24.2
Bi-Rotational
SAE -12
SAE B 4 Bolt SAE B 13T
M330A 842 VR EB10 -25 32.3
M330A 842 VR EB12 -25 40.4
M330A 842 VN EB15 -25 48.4
SAE -16M330A 842 VN EB17 -25 56.5
M330A 842 VN EB20 -25 64.6
SAE BB 15T Shaft
M330A 842 VR EB07 -43 24.2
Bi-Rotational
SAE -12
SAE B 4 Bolt SAE BB 15T
M330A 842 VR EB10 -43 32.3
M330A 842 VR EB12 -43 40.4M330A 842 VN EB15 -43 48.4
SAE -16M330A 842 VN EB17 -43 56.5
M330A 842 VN EB20 -43 64.6
1.00 Diameter Keyed Shaft
M330A 842 VR EB07 -67 24.2
Bi-Rotational
SAE -12
SAE B 4 Bolt 1.00 Dia Keyed
M330A 842 VR EB10 -67 32.3
M330A 842 VR EB12 -67 40.4
M330A 842 VN EB15 -67 48.4
SAE -16M330A 842 VN EB17 -67 56.5
M330A 842 VN EB20 -67 64.6
SAE B 2 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE B 13T Shaft
M330A 897 VR EB07 -25 24.2
Bi-Rotational
SAE -12
SAE B 2 Bolt SAE B 13T
M330A 897 VR EB10 -25 32.3
M330A 897 VR EB12 -25 40.4
M330A 897 VN EB15 -25 48.4
SAE -16M330A 897 VN EB17 -25 56.5
M330A 897 VN EB20 -25 64.6
SAE BB 15T Shaft
M330A 897 VR EB07 -43 24.2
Bi-Rotational
SAE -12
SAE B 2 Bolt SAE BB 15T
M330A 897 VR EB10 -43 32.3
M330A 897 VR EB12 -43 40.4
M330A 897 VN EB15 -43 48.4
SAE -16M330A 897 VN EB17 -43 56.5
M330A 897 VN EB20 -43 64.6
1.00 Diameter Keyed Shaft
M330A 897 VR EB07 -67 24.2
Bi-Rotational
SAE -12
SAE B 2 Bolt 1.00 Dia Keyed
M330A 897 VR EB10 -67 32.3
M330A 897 VR EB12 -67 40.4
M330A 897 VN EB15 -67 48.4SAE -16M330A 897 VN EB17 -67 56.5
M330A 897 VN EB20 -67 64.6
5/26/2018 Commercial Gear Quick Reference
16/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B15 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P350 GEAR PUMPS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P350A 478 EG AB07 -0731.3
Clockwise
SAE 2 SAE 1 SAE C 4 Bolt SAE C 14T
P350A 578 GE AB07 -07 Anti-clockwise
P350A 478 EG AB10 -0741.8
Clockwise
P350A 578 GE AB10 -07 Anti-clockwise
P350A 478 EG AB12 -0752.2
Clockwise
P350A 578 GE AB12 -07 Anti-clockwise
P350A 478 EG AB15 -0762.7
Clockwise
P350A 578 GE AB15 -07 Anti-clockwise
P350A 478 EG AB17 -0773.1
Clockwise
P350A 578 GE AB17 -07 Anti-clockwiseP350A 478 EG AB20 -07
83.6Clockwise
P350A 578 GE AB20 -07 Anti-clockwise
P350A 478 EG AB22 -0794
Clockwise
P350A 578 GE AB22 -07 Anti-clockwise
P350A 478 EG AB25 -07104.5
Clockwise
P350A 578 GE AB25 -07 Anti-clockwise
1.25 Keyed Shaft
P350A 478 EG AB07 -1131.3
Clockwise
SAE 2 SAE 1 SAE C 4 Bolt 1.25Keyed
P350A 578 GE AB07 -11 Anti-clockwise
P350A 478 EG AB10 -1141.8
Clockwise
P350A 578 GE AB10 -11 Anti-clockwise
P350A 478 EG AB12 -1152.2
Clockwise
P350A 578 GE AB12 -11 Anti-clockwise
P350A 478 EG AB15 -1162.7
Clockwise
P350A 578 GE AB15 -11 Anti-clockwise
P350A 478 EG AB17 -1173.1
Clockwise
P350A 578 GE AB17 -11 Anti-clockwise
P350A 478 EG AB20 -1183.6
Clockwise
P350A 578 GE AB20 -11 Anti-clockwise
P350A 478 EG AB22 -1194
Clockwise
P350A 578 GE AB22 -11 Anti-clockwise
P350A 478 EG AB25 -11
104.5
Clockwise
P350A 578 GE AB25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
17/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B16 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P350 GEAR PUMPS
SAE C 2 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P350A 498 EG AB07 -0731.3
Clockwise
SAE 2 SAE 1 SAE C 2 Bolt SAE C 14T
P350A 598 GE AB07 -07 Anti-clockwise
P350A 498 EG AB10 -0741.8
Clockwise
P350A 598 GE AB10 -07 Anti-clockwise
P350A 498 EG AB12 -0752.2
Clockwise
P350A 598 GE AB12 -07 Anti-clockwise
P350A 498 EG AB15 -0762.7
Clockwise
P350A 598 GE AB15 -07 Anti-clockwise
P350A 498 EG AB17 -0773.1
Clockwise
P350A 598 GE AB17 -07 Anti-clockwiseP350A 498 EG AB20 -07
83.6Clockwise
P350A 598 GE AB20 -07 Anti-clockwise
P350A 498 EG AB22 -0794
Clockwise
P350A 598 GE AB22 -07 Anti-clockwise
P350A 498 EG AB25 -07104.5
Clockwise
P350A 598 GE AB25 -07 Anti-clockwise
1.25 Keyed Shaft
P350A 498 EG AB07 -1131.3
Clockwise
SAE 2 SAE 1 SAE C 2 Bolt 1.25Keyed
P350A 598 GE AB07 -11 Anti-clockwise
P350A 498 EG AB10 -1141.8
Clockwise
P350A 598 GE AB10 -11 Anti-clockwise
P350A 498 EG AB12 -1152.2
Clockwise
P350A 598 GE AB12 -11 Anti-clockwise
P350A 498 EG AB15 -1162.7
Clockwise
P350A 598 GE AB15 -11 Anti-clockwise
P350A 498 EG AB17 -1173.1
Clockwise
P350A 598 GE AB17 -11 Anti-clockwise
P350A 498 EG AB20 -1183.6
Clockwise
P350A 598 GE AB20 -11 Anti-clockwise
P350A 498 EG AB22 -1194
Clockwise
P350A 598 GE AB22 -11 Anti-clockwise
P350A 498 EG AB25 -11
104.5
Clockwise
P350A 598 GE AB25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
18/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B17 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
M350 GEAR MOTORS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE C 14T Shaft
M350A 878 VR EB07 -07 31.3
Bi-Rotational
SAE -12
SAE C 4 Bolt SAE C 14T
M350A 878 VR EB10 -07 41.8
M350A 878 VR EB12 -07 52.2
M350A 878 VN EB15 -07 62.7
SAE -16
M350A 878 VN EB17 -07 73.1
M350A 878 VN EB20 -07 83.6
M350A 878 VN EB22 -07 94
M350A 878 VN EB25 -07 104.5
1.25 Keyed Shaft
M350A 878 VR EB07 -11 31.3
Bi-Rotational
SAE -12
SAE C 4 Bolt 1.25 Keyed
M350A 878 VR EB10 -11 41.8
M350A 878 VR EB12 -11 52.2
M350A 878 VN EB15 -11 62.7
SAE -16
M350A 878 VN EB17 -11 73.1
M350A 878 VN EB20 -11 83.6
M350A 878 VN EB22 -11 94
M350A 878 VN EB25 -11 104.5
SAE C 2 BOLT
Stock Code
Displacement
cc/rev Shaft Rotation
Ports
O-Ring Boss Mount Shaft
SAE C 14T Shaft
M350A 898 VR EB07 -07 31.3
Bi-Rotational
SAE -12 SAE C 2 Bolt SAE C 14T
M350A 898 VR EB10 -07 41.8 SAE -12 SAE C 2 Bolt SAE C 14T
M350A 898 VR EB12 -07 52.2 SAE -12 SAE C 2 Bolt SAE C 14T
M350A 898 VN EB15 -07 62.7 SAE -16 SAE C 2 Bolt SAE C 14T
M350A 898 VN EB17 -07 73.1 SAE -16 SAE C 2 Bolt SAE C 14T
M350A 898 VN EB20 -07 83.6 SAE -16 SAE C 2 Bolt SAE C 14T
M350A 898 VN EB22 -07 94 SAE -16 SAE C 2 Bolt SAE C 14T
M350A 898 VN EB25 -07 104.5 SAE -16 SAE C 2 Bolt SAE C 14T
1.25 Keyed Shaft
M350A 898 VR EB07 -11 31.3
Bi-Rotational
SAE -12 SAE C 2 Bolt 1.25 KeyedM350A 898 VR EB10 -11 41.8 SAE -12 SAE C 2 Bolt 1.25 Keyed
M350A 898 VR EB12 -11 52.2 SAE -12 SAE C 2 Bolt 1.25 Keyed
M350A 898 VN EB15 -11 62.7 SAE -16 SAE C 2 Bolt 1.25 Keyed
M350A 898 VN EB17 -11 73.1 SAE -16 SAE C 2 Bolt 1.25 Keyed
M350A 898 VN EB20 -11 83.6 SAE -16 SAE C 2 Bolt 1.25 Keyed
M350A 898 VN EB22 -11 94 SAE -16 SAE C 2 Bolt 1.25 Keyed
M350A 898 VN EB25 -11 104.5 SAE -16 SAE C 2 Bolt 1.25 Keyed
5/26/2018 Commercial Gear Quick Reference
19/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B18 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P365 GEAR PUMPS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P365A 478 EG AB07 -0744.3
Clockwise
SAE 2 SAE 1
SAE C 4 Bolt SAE C 14T
P365A 578 GE AB07 -07 Anti-clockwise
P365A 478 EG AB10 -0759
Clockwise
P365A 578 GE AB10 -07 Anti-clockwise
P365A 478 EG AB12 -0773.8
Clockwise
P365A 578 GE AB12 -07 Anti-clockwise
P365A 478 EG AB15 -0788.5
Clockwise
P365A 578 GE AB15 -07 Anti-clockwise
P365A 478 EF AB17 -07103.3
Clockwise
SAE 2 SAE 1
P365A 578 FE AB17 -07 Anti-clockwiseP365A 478 EF AB20 -07
118Clockwise
P365A 578 FE AB20 -07 Anti-clockwise
P365A 478 EF AB22 -07132
Clockwise
P365A 578 FE AB22 -07 Anti-clockwise
P365A 478 EF AB25 -07147.5
Clockwise
P365A 578 FE AB25 -07 Anti-clockwise
1.25 Keyed Shaft
P365A 478 EG AB07 -1144.3
Clockwise
SAE 2 SAE 1
SAE C 4 Bolt1.25
Keyed
P365A 578 GE AB07 -11 Anti-clockwise
P365A 478 EG AB10 -1159
Clockwise
P365A 578 GE AB10 -11 Anti-clockwise
P365A 478 EG AB12 -1173.8
Clockwise
P365A 578 GE AB12 -11 Anti-clockwise
P365A 478 EG AB15 -1188.5
Clockwise
P365A 578 GE AB15 -11 Anti-clockwise
P365A 478 EF AB17 -11103.3
Clockwise
SAE 2 SAE 1
P365A 578 FE AB17 -11 Anti-clockwise
P365A 478 EF AB20 -11118
Clockwise
P365A 578 FE AB20 -11 Anti-clockwise
P365A 478 EF AB22 -11132
Clockwise
P365A 578 FE AB22 -11 Anti-clockwise
P365A 478 EF AB25 -11
147.5
Clockwise
P365A 578 FE AB25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
20/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B19 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
P365 GEAR PUMPS
SAE C 2 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Inlet Port
SAE Split Flange
Pressure Port
SAE Split FlangeMount Shaft
SAE C 14T Shaft
P365A 498 EG AB07 -0744.3
Clockwise
SAE 2 SAE 1
SAE C 2 Bolt SAE C 14T
P365A 598 GE AB07 -07 Anti-clockwise
P365A 498 EG AB10 -0759
Clockwise
P365A 598 GE AB10 -07 Anti-clockwise
P365A 498 EG AB12 -0773.8
Clockwise
P365A 598 GE AB12 -07 Anti-clockwise
P365A 498 EG AB15 -0788.5
Clockwise
P365A 598 GE AB15 -07 Anti-clockwise
P365A 498 EF AB17 -07103.3
Clockwise
SAE 2 SAE 1
P365A 598 FE AB17 -07 Anti-clockwiseP365A 498 EF AB20 -07
118Clockwise
P365A 598 FE AB20 -07 Anti-clockwise
P365A 498 EF AB22 -07132
Clockwise
P365A 598 FE AB22 -07 Anti-clockwise
P365A 498 EF AB25 -07147.5
Clockwise
P365A 598 FE AB25 -07 Anti-clockwise
1.25 Keyed Shaft
P365A 498 EG AB07 -1144.3
Clockwise
SAE 2 SAE 1
SAE C 2 Bolt1.25
Keyed
P365A 598 GE AB07 -11 Anti-clockwise
P365A 498 EG AB10 -1159
Clockwise
P365A 598 GE AB10 -11 Anti-clockwise
P365A 498 EG AB12 -1173.8
Clockwise
P365A 598 GE AB12 -11 Anti-clockwise
P365A 498 EG AB15 -1188.5
Clockwise
P365A 598 GE AB15 -11 Anti-clockwise
P365A 498 EF AB17 -11103.3
Clockwise
SAE 2 SAE 1
P365A 598 FE AB17 -11 Anti-clockwise
P365A 498 EF AB20 -11118
Clockwise
P365A 598 FE AB20 -11 Anti-clockwise
P365A 498 EF AB22 -11132
Clockwise
P365A 598 FE AB22 -11 Anti-clockwise
P365A 498 EF AB25 -11
147.5
Clockwise
P365A 598 FE AB25 -11 Anti-clockwise
5/26/2018 Commercial Gear Quick Reference
21/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B20 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
M365 GEAR MOTORS
SAE C 4 BOLT
Stock CodeDisplacement
cc/revShaft Rotation
Ports
O-Ring BossMount Shaft
SAE C 14 T Shaft
M365A 878 VN EB07 -07 44.3 Bi-Rotational
SAE -16
SAE C 4 Bolt SAE C 14T
M365A 878 VN EB10 -07 59 Bi-Rotational
M365A 878 VN EB12 -07 73.8 Bi-Rotational
M365A 878 VN EB15 -07 88.5 Bi-Rotational
M365A 878 VC EB17 -07 103.3 Bi-Rotational
SAE -20M365A 878 VC EB20 -07 118 Bi-Rotational
M365A 878 VC EB22 -07 132 Bi-Rotational
M365A 878 VC EB25 -07 147.5 Bi-Rotational
1.25" Keyed Shaft
M365A 878 VN EB07 -11 44.3 Bi-RotationalSAE -16
SAE C 4 Bolt 1.25 Keyed
M365A 878 VN EB10 -11 59 Bi-Rotational
M365A 878 VN EB12 -11 73.8 Bi-Rotational
M365A 878 VN EB15 -11 88.5 Bi-Rotational
M365A 878 VC EB17 -11 103.3 Bi-Rotational
SAE -20M365A 878 VC EB20 -11 118 Bi-Rotational
M365A 878 VC EB22 -11 132 Bi-Rotational
M365A 878 VC EB25 -11 147.5 Bi-Rotational
SAE C 2 BOLT
Stock CodeDisplacement
cc/rev Shaft RotationPorts
O-Ring Boss Mount Shaft
SAE C 14T Shaft
M365A 878 VN EB07 -07 44.3
Bi-Rotational
SAE -16
SAE C 2 Bolt SAE C 14T
M365A 878 VN EB10 -07 59
M365A 878 VN EB12 -07 73.8
M365A 878 VN EB15 -07 88.5
M365A 878 VC EB17 -07 103.3
SAE -20M365A 878 VC EB20 -07 118
M365A 878 VC EB22 -07 132
M365A 878 VC EB25 -07 147.5
1.25"Keyed Shaft
M365A 878 VN EB07 -11 44.3
Bi-Rotational
SAE -16
SAE C 2 Bolt 1.25 Keyed
M365A 878 VN EB10 -11 59
M365A 878 VN EB12 -11 73.8
M365A 878 VN EB15 -11 88.5
M765A 878 VC EB17 -11 103.3
SAE -20M365A 878 VC EB20 -11 118
M365A 878 VC EB22 -11 132
M365A 878 VC EB25 -11 147.5
5/26/2018 Commercial Gear Quick Reference
22/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B21 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
30/50/75 SERIES SPARE PARTS
P30/M30
Part Number Description
3910381040 Outboard Bearing
3910381068 Roller Bearing3912185013 Thrust Plate Pump
3912185013 Thrust Plate Motor
3912585006 Ring Seal
3912882051 Seal Strip
3912883058 Pump Shaft Seal
3912883107 Pump Shaft Seal to suit C Shaft
3912883119 Motor Shaft Seal
3912883126 Motor Shaft Seal to suit C Shaft
3912884050 Housing Gasket
3913681001 Check Valve Assembly
P50/M50
Part Number Description
3910381077 Outboard Bearing
3910381059 Roller Bearing
3912185012 Thrust Plate Pump
3912185012 Thrust Plate Motor
3912585009 Ring Seal
3912882051 Seal Strip
3912883103 Pump Shaft Seal
3912883133 Pump Shaft Seal to suit C Shaft
3912883115 Motor Shaft Seal
3912883115 Motor Shaft Seal to suit C Shaft
3912884021 Housing Gasket
3913681001 Check Valve Assembly
P75/M75
Part Number Description
3910381078 Outboard Bearing
3910381060 Roller Bearing
3912185020 Standard Thrust Plate
3912185040 Reduced Area Thrust Plate
3912585011 Ring Seal
3912881457 0- Ring (N0674 2-146)
3912882084 Seal Strip
3912883052 Pump Shaft Seal
3912883052 Pump Shaft Seal to suit C Shaft
3912883094 Motor Shaft Seal
3912883094 Motor Shaft Seal to suit C Shaft3912884024 Housing Gasket
3912885040 Reduced Area T/Plate Seal Rings
5/26/2018 Commercial Gear Quick Reference
23/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B22 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
31/51/76 SERIES SPARE PARTS
P31/M31
Part Number Description
3910381040 Outboard Bearing
3910381068 Roller Bearing3912082032 Dowel Pin
3912185031 Thrust Plate Pump
3912185013 Thrust Plate Motor
3912585006 Ring Seal
3912882051 Seal Strip
3912883058 Pump Shaft Seal
3912883107 Pump Shaft Seal to suit C Shaft
3912883119 Motor Shaft Seal
3912883126 Motor Shaft Seal to suit C Shaft
3912884050 Housing Gasket
3913681001 Check Valve Assembly
P51/M51Part Number Description
3910381077 Outboard Bearing
3910381059 Roller Bearing
3912082032 Dowel Pin
3912185029 Thrust Plate Pump
3912185012 Thrust Plate Motor
3912585009 Ring Seal
3912882051 Seal Strip
3912883103 Pump Shaft Seal
3912883133 Pump Shaft Seal to suit C Shaft
3912883115 Motor Shaft Seal
3912883115 Motor Shaft Seal to suit C Shaft
3912884021 Housing Gasket
P76/M76
Part Number Description
3910381078 Outboard Bearing
3910381060 Roller Bearing
3912082033 Dowel Pins
3912185026 Thrust Plate Pump
3912185020 Thrust Plate Motor
3912585011 Ring Seal
3912881457 0- Ring (N0674 2-216)
3912882084 Seal Strip
3912883052 Pump Shaft Seal
3912883052 Pump Shaft Seal to suit C Shaft3912883094 Motor Shaft Seal
3912883094 Motor Shaft Seal to suit C Shaft
3912884024 Housing Gasket
3912885040 Reduced Area T/Plate Seal Rings
5/26/2018 Commercial Gear Quick Reference
24/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B23 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
315/330 SERIES SPARE PARTS
P315/M315
Part Number Description
3910482195 Bushing
3912082071 Dowel Pin3912185063 Pump Thrust Plate
3912185070 Motor Thrust Plate
3912883151 Pump Shaft Seal
3912883156 Motor Shaft Seal
3912883168 Pump Channel Seal
3912883169 Pump Channel Seal
3912881995 Motor Channel Seal
3912881996 Motor Channel Seal (End)
3912881997 Motor Channel Seal (Side)
3912881968 Housing Gasket
3913384313 Motor Seal Retainer
3912881429 Motor Housing Gasket
P330/M330
Part Number Description
3910381040 Outboard Bearing
3910482306 Bushing
3912082032 Dowel Pin
3912185056 Pump Thrust Plate
3912185065 Motor Thrust Plate
3912883058 Pump Shaft Seal
3912883119 Motor Shaft Seal
3912883166 Pump Channel Seal
3912883167 Pump Channel Seal
3912881929 Motor Channel Seal
3912881930 Motor Channel Seal (End)
3912881931 Motor Channel Seal (Side)3912884050 Pump Housing Gasket
3912884076 Motor Housing Gasket
3913381040 Motor Seal Retainer
5/26/2018 Commercial Gear Quick Reference
25/26
COMMERCIAL GEAR PUMPS & MOTORS
1300 493 728 Section 6 Page B24 www.cfphydraulics.com.au
1300 806 330 Quick Refernce CFP06B1201 [email protected]
350/365 SERIES SPARE PARTS
P350/M350
Part Number Description
3910381077 Outboard Bearing
3910482308 Bushing3912082032 Dowel Pin
3912185057 Pump Thrust Plate
3912185068 Motor Thrust Plate
3912883103 Pump Shaft Seal
3912883115 Motor Shaft Seal
3912882139 Pump Channel Seal
3912882140 Pump Channel Seal
3912885073 Motor Channel Seal
3912885074 Motor Channel Seal
3912885075 Motor Channel Seal
3912884074 Pump Housing Gasket
3912884021 Motor Housing Gasket
P365/M365
Part Number Description
3910381078 Outboard Bearing
3910482307 Bushing
3912082062 Pump Hollow Dowel
3912082069 Motor Hollow Dowel
3912185055 Pump Thrust Plate
3912185060 Motor Thrust Plate
3912883052 Pump Shaft Seal
3912883094 Motor Shaft Seal
3912884052 Pump Housing Gasket
3912884023 Motor Housing Gasket
3912885064 Pump Viton Channel Seal
3912883176 Pump Channel Seal3912883177 Pump Channel Seal
3912885069 Motor Side Channel Seal
3912885070 Motor End Channel Seal
3912885071 Motor Channel Seal
STANDARD SEAL KITS, SOFT SEALS ONLY
Series Single # Tandem # Triple #
P20 P20SK1 P20SK2 P20SK3
P30/31 P30SK1 P30SK2 P30SK3
P50/51 P50SK1 P50SK2 P50SK3P75/76 P75SK1 P75SK2 P75SK3
M20 M20SK1 M20SK2 M20SK3
M30/31 M30SK1 M30SK2 M30SK3
M50/51 M50SK1 M50SK2 M50SK3
M75/76 M75SK1 M75SK2 M75SK3
P315 P315SK1 P315SK2 P315SK3
P330 P330SK1 P330SK2 P330SK3
P350 P350SK1 P350SK2 P350SK3
P365 P365SK1 P365SK2 P365SK3
M315 M315SK1 M315SK2 M315SK3
M330 M330SK1 M330SK2 M330SK3
M350 M350SK1 M350SK2 M350SK3
M365 M365SK1 M365SK2 NA
5/26/2018 Commercial Gear Quick Reference
26/26
TERMS & CONDITIONS OF TRADE
1. DEFINITIONS
1.1 Agreement means the terms and conditions contained herein.
1.2 Services means and includes all of the services to be provided by this
agreement.
1.3 Supplier means Lacedan Pty Ltd (ACN 100 965 204) carrying on
business as CFP Hydraulics including any subsidiary or affiliate
companies and its officers, servants, agents or subcontractors and their
employees;
1.4 Goods means the goods to be supplied under this agreement;
1.5 Customer means the person or persons on whose behalf or at whose
request the services and/or goods are to be provided under this
agreement.
2. APPLICATION
2.1 These terms and conditions (terms) of trade apply to every contractwith the Supplier subject to any written agreement by the Supplier to
modify the same signed by the Supplier.
2.2 These terms shall apply notwithstanding the receipt,acknowledgement or acceptance by the Supplier of any Purchase
Order issued by the Customer purporting to modify these terms.
3. CHARGES
3.1 The price involved on the Order Form is due and payable by the
Customer on the supply of the S ervices and/or Goods to the Customer.
If for any reason the Supplier is unable to provide all Services and/or
Goods due to no fault on the part of the Supplier then the Supplier
shall be entitled to a pro-rata payment of the amount invoiced in the
Order Form for the Services and for the full amount for any Services
and/or Supplied.
3.2 Unless otherwise specified goods and services tax (GST) and any
other applicable duties and charges imposed by any government or
statutory authority are additional to the price quoted and invoiced.
Where GST is included in a quotation it is based on the rate ruling at
the time of the quotation and any subsequent variation is to the
Customers account. Where GST is not included the Customer is liable
to pay such tax.
4. DELIVERY OF GOODS
4.1 The Supplier may charge the Customer a delivery fee for all or any
costs and expenses to and arising out of the delivery of any Goods to
the Supplier from any manufacturer or other supplier.
4.2 The Supplier may also charge the Customer a delivery fee for all or anycosts and expenses incurred to and arising out of the delivery of Goods
and Services to the Customer where delivery is to a place other than
the Suppliers premises.
4.3 Where Goods are to be collected by the Customer from the Suppliers
premises then the Goods must be collected within 5 days from the
date of notification from the Supplier to the Customer that the Goods
are ready for collection. If the Goods are not so collected then delivery
dates are approximate only. The Supplier is not liable for delay in
delivery howsoever caused. Time for delivery is not of the essence.
The Supplier may deliver in advance of the quoted delivery date (if
any).
5. RISK
5.1 Risk in the Goods passes to the Customer either:
(a) on collection of the Goods by the Customer; or
(b) at the time the Supplier notifies the Customer that the Goods
are available for collection; or
(c) where the Goods are to be delivered to the Customer on leaving
the Suppliers premises.
6. OWNERSHIP
6.1 Ownership of any Goods only passes to the Customer when the
Customer pays all sums owing to the Supplier under this and any othercontract.
6.2 Where the Supplier delivers the Goods to the Customer and moneys
are still outstanding to the Supplier, then, until the Goods are disposed
of by the Customer in accordance with the provisions of this clause,
the Customer agrees with the Supplier to keep as a fiduciary for the
Supplier and, if required, store the Goods in a manner that clearly
shows the ownership of the Supplier.
6.3 The Customer may sell the Goods to a third party in the normal course
of business and deliver them to that third party whereupon:
(a) if the Customer is paid by that party, the Customer holds the
whole of the proceeds of sale of those Goods on trust for the
Supplier; and
(b) if the Customer is not paid by that third party, the Customer
agrees at the option of the Supplier to assign his claim against
that party upon the Supplier giving the Customer notice in
writing to that effect.
6.4 For the purpose of giving effect to the performing the agreement
specified in paragraph 6.3(b) the Customer irrevocably appoints the
Supplier as his attorney.
6.5 The provisions of this clause apply notwithstanding any agreement,
whether subsequent to this agreement or not, between the parties
under which the Supplier gives the Customer credit.6.6 Where:
(a) the Customer or the Supplier repairs an object or makes a new
object from the Goods;
(b) the Customer or the Supplier mixed the Goods with other
objects; or
(c) the Goods become part of other objects, then the ownership of
new or the other objects immediately passes to the Supplier and
the Customer is to hold the new object or other objects as a
fiduciary for the Supplier.
6.7 The ownership of the new object or other objects passes to the
Supplier at the beginning of the single operation or event by which the
Goods are converted into a new object, is mixed or becomes part of
another object (called New Object).
6.8 Until the Supplier has been paid all moneys owing under this or any
other Contract, the Buyers agrees with the Supplier to keep the New
Object as fiduciary for the Supplier and, if required by the Supplier to
store the New Object in a manner that clearly shows the ownership of
the Supplier.
7. DELIVERY AND COMPLETIONS OF SERVICES
7.1 The Customer acknowledges and agrees that the Supply of any Services
to the Customer for the installation repair or maintenance of an object
or in the possession of the Customer shall be in accordance with the
design and specifications of the original manufacturer of the object
wherever possible unless the Supplier is otherwise directed by the
Customer.
7.2 Where the Customer requires the Supplier to design any object for
installation repair or maintenance purposes the Supplier shall have the
right to require the Customer (at the Customers cost) to obtain such
expert services as is necessary including engineers specifications or
drawings in order to ensure that the design and specifications meet
relevant safety standards. The Supplier does not hold itself out as
having necessary expertise and to the fullest extend permissible by the
law accepts no responsibility for the design and specifications.
7.3 It shall be the responsibility of the Customer to provide wherever
possible the specifications of the original manufacturer of the object
and any manuals and other documents which relate to the object.
These are to be provided to the Supplier prior to the provision of the
Supply of the Services in relation to the object.
7.4 Where the Customer requires the Object to be installed required or
maintained in a modification of the manufacturers specifications for
the object it shall be the responsibility of the Customer to ensure that
such modification is legal. The Supplier accepts no responsibility for
modification to an object to be outside the manufacturers
specifications unless the manufacture has provided in writing approval
to such modifications.
7.5 The Customer acknowledges that where the object is to be modified by
the Supplier, the Supplier shall be indemnified by the Customer for any
loss or damage which the Customer suffers as a result of the
modification.
7.6 The Supplier shall use its best endeavours to supply the Services and
Part on the times and dates specified but shall not be liable for anydelays whatsoever.
8. LIABILITY OF SUPPLY
8.1 The Supplier is not responsible or liable for:-
(a) The workmanship of Goods Supplied, however the Supplier shalluse its best endeavours to ensure that the Goods provides or
assigns warranties in relation to the Goods to the Customer;
(b) Any faults or defects in the Goods;(c) The quality and/or performance of the Goods which were
purchased by the supplier from the manufacturer; or
(d) Delay in performance or non-performance of this Contract ordirectly or indirectly caused by fire, explosion, accident, flood,
labour trouble, stoppage or strikes, shortages, acts of war or
hostilities by any Government Agencies, inability to obtain
suitable materials, equipment, fuel, power or transport at
current prices, or act of God or arising from contingencies
happening or causes beyond the control of the Supplier.
8.2 Any Goods or services affected by any matters outlined in the
preceding clause may be eliminated by the Supplier from this contract
without liability for breach thereof but this contract shall otherwise
remain unaffected.
9. SUPPLIERS AND WARRANTIES9.1 Nothing herein shall exclude, restrict or modify any terms, conditions,
warranty or liability implied into this contract by statute, where to do
so would render any provisions of this contract void.
9.2 Subject to the preceding clause the Suppliers liability for the supply of
Services and/or Goods limited to the warranties compulsorily imposed
upon the Australian Consumer Lawor other Statute and any implied
conditions warranties and liabilities including for consequential loss or
for loss arising from negligence are hereby excluded.
9.3 Where it is legally permitted, any remaining liability implied by statute
or resulting from a breach of any condition or warranty implied by
statute is limited to replacement of the Goods or re-supply of the
Services at the Suppliers option.
10. ASSIGNMENT
10.1 The Customer cannot assign its interest in the contract.
11. NOTICES
11.1 A party hereto shall be deemed to have received a document
mentioned herein on the day such document is delivered or, if posted
on the second day after posting.
12. SUBCONTRACT
12.1 The Supplier shall be entitled to subcontract on any terms the whole or
any part of the order for the supply of Goods and/or Services.
SPECIAL CONDITIONS
These are special conditions which form part of the Terms of Supply. To the
extent of any inconsistency these special conditions shall prevail. For the
purposes of this agreement The Works shall mean all action reasonably
necessary to supply the Services and or Goods and anything reasonably
incidental thereto.
13. LIMITATIONS AND EXCLUSIONS
13.1 If the Customer is a consumer under the Australian Consumer Law
(and/or any equivalent state fair trading legislation) (The Act) then:-
(a) The Customers right under the Act are excluded, restricted ormodified by anything herein;
(b) The Suppliers liability for the supply of Goods and/or Services islimited to one or more of the following at the election of the
supplier:-
(1) The replacement of the Goods or the S upply of equivalentGoods and/or repair of the Goods.
(2) The payment of the cost of replacing the Goods oracquiring equivalent Goods or the payment of the cost of
having the Goods repaired.
(3) The Supply of the Services again; or(4) The payment of the cost of having services supplied again.
13.2 Goods not manufactured by the Supplier are supplied on the basis that
the Supplier will assign to the Customer any rights under any warranty
to such, Goods from the manufacturer and/or others and the Supplier
is not liable for any loss or damage arising from any deficiencies or
defect in such Goods except to the extent that the warranties are
honored by the original manufacturer.
13.3 Subject to clause 8 and this clause 13 the Supplier is not liable to the
Customer for any loss or damages (including consequential loss) to the
Goods, object or other including any goods left by the Customer in the
Suppliers care and/or control or for the death or personal injury
howsoever arising which is suffered or incurred by the Customer
arising out of:-
(a) Any act or omission (whether negligent or otherwise) by the
Supplier while undertaking the Supply of the Goods and/or
services;
(b) Any breach of any contract or any bailment or other obligation
imposed on the Supplier in respect of the Supply of the Goods
and/or Services;
(c) Any misuse, abuse or incorrect use or lack of or defective
maintenance of any property of the Customer alter delivery of
the Goods and/or Services; or
(d) Faulty installation of any Goods by any third person engaged by
the customer; or
(e) Any representation as to the performance, the suitable
application or use of the Goods or otherwise in respect of the
Goods made by any employee or agent of the Supplier unless in
writing signed by an authorized person for the Supplier.
13.4 Subject to this clause 12, any implied conditions, warranties and
liabilities including for consequential loss and/or losses arising from
negligence are hereby excluded.
14. INDEMNITIES
14.1 The Customer will indemnify and save harmless the Supplier from and
against any expense, claim, loss or damage arising by the Supplier
because of any breach by the Customer if any of these Terms and
Conditions or to the Suppliers equipment or to property or person
which occurs due to any act or omission by the Customer.
14.2 For the purposes of clause 13.1 loss includes consequential loss of any
fine, levy, charge or any monetary imposition to which the Supplier
becomes liable as an incident to the supply of Goods or Services and/or
resulting by any breach by the Customer of this agreement.
15. PROJECTS
15. Persons and Property.
15.1 The parties acknowledge that for the provision of the Goods and/or
services one or more of the following may be necessary:-
(a) The operation of the object and any machinery part or device
whatsoever connected to or in relation to the object.
(b) The movement of the object by whatever means necessary
whether on land and/or on sea in whatever circumstances
considered necessary and appropriate by the Supplier.
(c) The carrying out of any rectification, alternation, adjustment,
repair or installation as is in the Supplier s opinion necessary to
give effect to the Customers instruction.
(d) Hiring, renting or leasing of suitable apparatus and or premises
including hard stand from third party.
(e) Obtaining of government statutory licenses or approvals and/or
compliance with a number or statutory and regulatory
requirements.
15.2 The Customer agrees to and authorizes the Supplier to:-
(a) Take all action reasonably necessary to provide the Services and
or supply the Goods;
(b) Operate its machinery, Goods, devices and/or the object
whatsoever;
(c) Move any object by whatever means necessary whether on land
or on sea in whatever circumstances as the Supplier considers
necessary and appropriate.
(d) Carry out any rectification, alteration repair or installation as in
the Suppliers opinion necessary to give effect to the Customers
instructions.
16. RISK16.1 Risk of damage to or loss of Works rest with the Customers from the
date of this agreement.
16.2 Subject to the other terms of this agreement, the Supplier is not liable
to the Customer for any loss or damage (including consequential loss)
to the works or the property of the Customer while in the care or
control of the Supplier or for the death or personal injury howsoever
arising which is suffered or incurred by the Customer arising out of:-
(a) Any act or omission (whether negligent or otherwise) by the
Supplier while undertaking the Works, or
(b) Any breach of any contract or other obligation imposed upon
the Supplier in respect by the Works undertaken by the Supplier.
17. INSURANCES
17.1 The Customer shall maintain in effect during the period whilst the
property of the customer is in the care or custody of the Supplier all
insurances as appropriate to the property including its operation,
including public liability insurance and workers compensation
insurance.
18. WORKPLACE HEATH AND SAFETY
18.1 A Customer shall comply with and ensure that it and its employees,
servants or agents comply with the Workplace Health and Safety Act or
equivalent legislation whilst the Supplier is performing the Works and
indemnifies the Suppliers against any liability or responsibility in
respect of any failure by the Customer or its employees, servants or
agents to comply.
19. HIRE, LEASE OR LICENCE
19.1 Unless otherwise agreed in writing, the Customer shall arrange for the
hire, lease or licensing of equipment and/or premises to enable the
Supplier to provide the Services or Goods.
19.2 The Customer shall arrange for the Supplier to have all necessary
access during working hours in order to carry out the Works.
20. ENVIRONMENTAL ISSUES
20.1 The Customer shall ensure that it and/or other relevant person/s shall
apply for and maintain all approvals, permits, licences and
authorisations which may be necessary under the Environmental
Protection Act Queensland 1994 and/or any other Environmental
Legislation (The Act) for and in relation to the exercise of its rights
and obligations under this agreement and to comply with all duties
under the Act.
DESIGNS AND MODIFICATIONS
21. INTELLECTUAL PROPERTY
21.1 Where the Supplier designs an object or part of an object for
construction, installation, repair or maintenance the intellectual
property in the designs including drawings, tracings, reproductions and
specifications shall remain the property of the Suppliers unless
otherwise agreed in writing. The Customer shall treat and maintain
confidential and secret all designs.
22. APPROVAL OF DESIGNS
22.1 It shall be the responsibility of the Customer to ensure that the designs
meet the Customers specifications and requirements. For this
purpose the Customer shall have the right to access the designs and to
take copies.
23. LOSS OF WARRANTY
23.1 The Customer acknowledges that any modifications to the Works
and/or Goods may result in the voiding of the warranties from
manufacturers and/or others. The Customer shall indemnify the
Supplier for any loss or damage suffered by the Supplier arising from
the voiding and or loss of such a warranty.
24. JURISDICTION
24.1 This agreement is governed by and is to be construed in accordance
with the laws of the State of Queensland.
25. DISPUTE RESOLUTIONS25.1 In the event of any dispute or difference arising between the Supplier
and the Customer, unless such dispute or difference is able to be
resolved by direct negotiations between the parties, it is agreed that
such dispute or difference shall be referred to mediation administered
by a person as the parties may determine by agreement or failing
agreement a person nominated by the President of the Queensland
Law Society. It is agreed that neither party will commence any Court
proceedings against the other unless and until their dispute has firstly
been referred to a mediation as stipulated aforesaid.
25.2 The parties hereto agree to submit to the nonexclusive jurisdiction of
the Courts Queensland.