Date post: | 25-May-2015 |
Category: |
Technology |
Upload: | emertxe-information-technologies-pvt-ltd |
View: | 2,687 times |
Download: | 28 times |
Team Emertxe
Communication Protocols 1
CommunicationProtocols I
● Introduction
● UART
● SPI
● I²C
● CAN
● USB
Introduction
Introduction
● What do mean by Communication?
● Mode of Communications
● Type of Communications
● Why Protocols?
IntroductionModes of Communication
● Simplex
● Half Duplex
● Duplex
UART
UART
Serial Peripheral Interface
SPI
● Introduction
● Interface
● Hardware Configurations
● Data Transmission
– Data Propagation
– Data Validity
SPIIntroduction
● Synchronous
● Full Duplex
● Master / Slave
SPIInterface
● SCLK● MOSI● MISO● nSS
SPIHardware Configuration
SPIHardware Configuration
SPIHardware Configuration
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Transmission
SPIData Validity
Inter Integrated Circuits
● Introduction to I²C
● I²C Bus Features
● The I²C Bus Protocol
● Bus Speeds
I2C
● Synchronous
● Half Duplex
● Multi Master / Slave
I2CIntroduction
● Two Line Interface
● Software Addressable
● Multi Master with CD
● Serial, 8 bit Oriented, Bidirectional with 4 Modes
● On Chip Filtering
I2CBus Features
● Example
● Signals
● A Complete Data Transfer
I2CProtocol
I2CExample
● Two-wired Interface
– SDA
– SCL● Wired-AND
● Conditions and Data Validity
● Transmission
I2CSignals
I2CSignals – Wired-AND
I2CSignals – Conditions and Data Validity
I2CSignals – Transmission
● Data on SDA
● Clocking on SCL
● Clock Synchronization
● Data Arbitration
I2CSignals – Data on SDA
I2CSignals – Data on SDA
I2CSignals – Data on SDA
I2CSignals – Data on SDA
I2CSignals – Data on SDA
I2CSignals – Clocking on SCL
I2CSignals – Clock Synchronization
I2CSignals – Data Arbitration
I2CA Complete Data Transfer
I2CBus Speeds
● Bidirectional Bus
– Standard Mode - 100 Kbit/s
– Fast Mode - 400 Kbits/s
– Fast Mode Plus - 1 Mbits/s
– High Speed Mode - 3.4 Mbits/s● Unidirectional Bus
– Ultra Fast Mode – 5 Mbits/s● Uses Push-Pull Drivers (No Pullups)
Controller Area Network
● Introduction to CAN● Basic Concepts● Message Transfer● Message Filtering● Message Validation● Coding● Error Handling● Fault Confinement● Oscillator Tolerance● Bit Timing Requirement
Controller Area Network
● Asynchronous● Half Duplex● Multi Master / Slave
CANIntroduction
● Example
● Versions
● Absence of node addressing
– Message identifier specifies contents and priority
– Lowest message identifier has highest priority
● Non-destructive arbitration system by CSMA with collision detection
● Simple Transmission Medium
– Twisted pair – CAN H and CAN L
● Properties
● Layered Architecture
CANBasic Concepts
CANBasic Concepts - Example
CANBasic Concepts - Versions
NOMENCLATURE STANDARDMAX SIGNALING
RATE IDENTIFIER
Low Speed CAN ISO 11519 125 kbps 11 bit
CAN 2.0A ISO 11898:1993 1 Mbps 11 bit
CAN 2.0B ISO 11898:1995 1 Mbps 29 bit
● Prioritization of Messages
● Guarantee of Latency Times
● Configuration of Flexibility
● Multicast Reception with Time Synchronization
● System wide Data Consistency
● Multi master
● Error Detection and Error Signaling
● Automatic Retransmission
● Distinction between temporary errors and permanent failures of nodes and autonomous switching off of defect nodes
CANBasic Concepts - Properties
CANBasic Concepts - Layered Architecture
CANBasic Concepts - Layered Architecture
CANBasic Concepts - Layered Architecture
CANMessage Transfer
● Frame Formats
– Standard Frame - 11 bits Identifiers
– Extended Frame - 29 bits Identifiers● Frame Types
– Data Frame
– Remote Frame
– Error Frame
– Overload Frame● Frame Fields
CANMessage Transfer - Frame Formats
CANMessage Transfer – Data Frame
● A data frame consists of seven fields: start-of-frame, arbitration, control, data, CRC, ACK, and end-of-frame.
CANMessage Transfer – Remote Frame
● Used by a node to request other nodes to send certain type of messages
● Has six fields as shown in above figure
– These fields are identical to those of a data frame with the exception that the RTR bit in the arbitration field is recessive in the remote frame.
CANMessage Transfer – Error Frame
● This frame consists of two fields.
– The first field is given by the superposition of error flags contributed from different nodes.
– The second field is the error delimiter.● Error flag can be either active-error flag or passive-error flag.
– Active error flag consists of six consecutive dominant bits.– Passive error flag consists of six consecutive recessive bits.
● The error delimiter consists of eight recessive bits.
CANMessage Transfer – Overload Frame
● Consists of two bit fields: overload flag and overload delimiter
● Three different overload conditions lead to the transmission of the overload frame:
– Internal conditions of a receiver require a delay of the next data frame or remote frame.
– At least one node detects a dominant bit during intermission.
– A CAN node samples a dominant bit at the eighth bit (i.e., the last bit) of an error delimiter or overload delimiter.
● Format of the overload frame is shown in above fig
● The overload flag consists of six dominant bits.
● The overload delimiter consists of eight recessive bits.
● Control Field
● Arbitration Field
● Data Field
● CRC Field
● ACK Field
CANMessage Transfer – Frame Fields
● The first bit is IDE bit for the standard format but is used as reserved bit r1 in extended format.
● r0 is reserved bit.
● DLC3…DLC0 stands for data length and can be from 0000 (0) to 1000 (8).
CANFrame Fields – Control Field
● The identifier of the standard format corresponds to the base ID in the extended format.
● The RTR bit is the remote transmission request and must be 0 in a data frame.
● The SRR bit is the substitute remote request and is recessive.
● The IDE field indicates whether the identifier is extended and should be recessive in the extended format.
● The extended format also contains the 18-bit extended identifier.
CANFrame Fields – Arbitration Field
● May contain 0 to 8 bytes of data
CANFrame Fields – Data Field
● It contains the 16-bit CRC sequence including CRC delimiter.
● The CRC delimiter is a single recessive bit.
CANFrame Fields – CRC Field
● Consists of two bits● The first bit is the acknowledgement bit. ● This bit is set to recessive by the transmitter,
but will be reset to dominant if a receiver acknowledges the data frame.
● The second bit is the ACK delimiter and is recessive.
CANFrame Fields – Ack Field
CANError Handling
● Error Detection
– Bit Error
– Stuff Error
– CRC Error
– Form Error
– Acknowledgment Error● Error Signaling
CANFault Confinement
● Counters– Transmit Error Counter & Receive Error Counter
Universal Serial Bus
● Introduction
● Technical Overview
● Interfaces
● Architecture
● Power Managment
● Communication Overview
● Extensions
– OTG
– Wireless
Universal Serial Bus
● Asynchronous
● Half Duplex
● Master / Slave
● Offers simple connectivity
● Low cost
● Ease of use
● Manages power efficiently
● Supports all kinds of Data
USBIntroduction
● Upstream Connection and Downstream Connection
● Device Speeds
– Low Speed cables at 1.5 Mbps
– Full Speed cables at 12 Mbps and
– High Speed cables at 480 Mbps
– Super Speed upto 5.0 Gbps (Raw throughput)
● Two types of Connectors
– Type A and Type B
– Sizes
● Standard, Mini, Micro
USBTechnical Overview
● USB 1.X and 2.0
– Vcc
– D-
– D+
– GND
● USB 3.0
– Older USB interface line plus
– SSTX+/-
– SSRX+/-
USBInterfaces
● Follows a Tiered star Topology and consists of
– Host controller
– Hubs
– Peripherals
USBArchitecture
USBArchitecture - Bus Topology
● Host recognizes the peripheral through a process called Enumerations
● Host communicates with the peripheral to learn its identity and identifies which device driver is required
● Host supplies the peripheral with an address
● Host is the controller of the entire network. e.g. PC
USBArchitecture - Host
● Allows many USB devices to share a single USB port
● USB devices with some incorporated intelligence
● Increase the logical and physical fan out
● Single upstream connection and one-many down stream connection
● Smart wire passing data between the peripheral and Host ● Direct connection exists between host and peripherals ● Two kinds of Hubs:
– Bus Powered Hub: Draws power from the host computers USB interface
– Self Powered Hub: Has a built in power supply.
USBArchitecture - Hubs
● Receive and respond to the commands from the host. E.g. Mice, Keyboard, Joysticks
● Two types of Peripherals – Standalone– Compound Device
USBArchitecture - Peripherals
● Peripherals connected regardless of the power state
● A pair of wires to supply power to the peripherals
● Manage power by enabling and disabling power to devices
● Removes electrically ill behaved systems from the network
USBPower Management
● End point is a unique point in the device which is the source or the receiver of the data
● End point has a definite address associated with it
● Codes indicate the type of transfer
● 16 end points within each device each end point has a 4 bit address
● End point “0” reserved for control transfers
USBCommunication Overview
● Transactions between the host and end point take place through virtual pipes
● Pipes are logical channels which connect the host to the end points
● Once the communication is established the end points return a descriptor
● Descriptor is a data structure tells the host about the end points configuration and expectations
USBCommunication Overview
USB supports four transfer types of data:
● Control Transfers: – Exchange information such as configuration, command
information , set up between host and end point
● Bulk Transfers:– Supports bulk amounts of data when timely delivery isn’t critical.
– e.g. Printers and Scanners
● Isochronous transfers: – Handle transfers like streaming data
● Interrupt transfers:– Poll devices to see if they need service
USBCommunication Overview
● USB 2.0
● PictBridge Standard to communicate imaging devices
● Microsoft X box console
● IBM Ultraport
● USB 1.0 OTG
● USB 1.0a supplement OTG
● Wireless USB
USBExtensions
● USB On-The-Go Technology is used to provide dual role to the peripherals
● Enables direct communication between the hosts without involving the processor
● Incorporates Mini A , Mini B, Mini AB plugs and receptacles
● Highly complex design
USBOTG
Advantages:
● Provides Dual Role Devices
● Introduces new connector types, Mini A, Mini B, Mini AB
● Provides with Aggressive Power Management
On the Go Functionality of the USB can be implemented:
● Using a Full solution Approach
● Using a USB microcontroller
● Designing a custom IC
USBOTG
● A Paradigm developed by Cypress that allows devices to be connected but appear as if they are connected to the host over normal USB connectivity
● Addresses many of the Design issues of Wireless networking
● An evolution that relies on familiar and existing technologies
● Desirable for point to point devices
● Features of Wireless USB are its Ease of use, simple connectivity and conservation of the battery power
USBWireless
Thank You