+ All Categories

Home > Documents > COMPOSITES ONE, IACMI, AND THE CLOSED MOLD ALLIANCE€¦ · COMPOSITES ONE, IACMI, AND THE CLOSED...

COMPOSITES ONE, IACMI, AND THE CLOSED MOLD ALLIANCE€¦ · COMPOSITES ONE, IACMI, AND THE CLOSED...

Date post:	08-Jul-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

Download Report this document

Share this document with a friend

Embed Size (px):

1

COMPOSITES ONE, IACMI, AND THE CLOSED MOLD ALLIANCE WORKSHOP SCHEDULE MARCH 31-APR 1 National Wind Technology Center Boulder, CO Focus: Advanced Composites / Wind Energy and Repair Davis Technical College - Freeport West Campus (D5) Salt Lake City, UT Focus: Advanced Composites / Aerospace Gulf State Community College Panama City, FL Focus: Advanced Composites / Aerospace Dayton Composites Center Dayton, OH Focus: Advanced Composites / Emerging Markets OCTOBER 27-28 AUGUST 4-5 JUNE 23-24 For More Information visit compositesone.com or email [email protected].

Transcript

Page 1: COMPOSITES ONE, IACMI, AND THE CLOSED MOLD ALLIANCE€¦ · COMPOSITES ONE, IACMI, AND THE CLOSED MOLD ALLIANCE WORKSHOP SCHEDULE MARCH 31-APR 1 National Wind Technology Center Boulder,

COMPOSITES ONE, IACMI, AND THE CLOSED MOLD ALLIANCE

WORKSHOP SCHEDULE

MARCH31-APR 1

National Wind Technology CenterBoulder, COFocus: Advanced Composites / Wind Energy and Repair

Davis Technical College - Freeport West Campus (D5)Salt Lake City, UT

Focus: Advanced Composites / Aerospace

Gulf State Community CollegePanama City, FLFocus: Advanced Composites / Aerospace

Dayton Composites CenterDayton, OH

Focus: Advanced Composites / Emerging MarketsOCTOBER

27-28

AUGUST4-5

JUNE23-24

For More Information visit compositesone.com or email [email protected].

Recommended

IACMI Overview Craig A. Blue, PhD CEO November 13, 2015.

IACMI-The Composites Institute - US Department of … - IACMI...IACMI-The Composites Institute U.S. Department of Energy Advanced Manufacturing Office Program Review Craig A. Blue,

IACMI Preliminary Technology Roadmap: Phase One 1 · PDF fileThe Institute is initially focused on three applications where advanced composites manufacturing can have significant national

Advanced Composite Solutions FAST · THERMALLY CONDUCTIVE MATERIALS Rapid Composites has the ability to design, tool, mold and safely post-process machine advanced thermally conductive

ADVANCED Composites Manufacturing INNOVATION · The Institute for Advanced Composites Manufacturing Innovation (IACMI) is the fifth Institute in the National Network of Manufacturing

Mold and mold making

INSTITUTE FOR ADVANCED COMPOSITES MANUFACTURING …€¦ · IACMI MEMBER SUPPORTERS FOR THE COMPOSITE SLED PROJECT The Institute for Advanced Composites Manufacturing Innovation (IACMI),

Proposed Rules and Regulations Mold Inspection and Remediation · mold inspection company, mold remediation company, or mold analysis laboratory or by an accredited mold training

iacmi.org · 2020. 6. 18. · optimized resins & sizings for vinyl ester / carbon fiber composites IACMI PA 16-0349-5.3-01 Joe Fox Director, Emerging & External Technologies Ashland

Workforce Development - IACMI · IACMI Workforce Development 3 IACMI’s workforce development goals: • To establish key partnerships that will deliver composites training that

IACMI Serves Today and Tomorrow- Gray & Herr, Other Ways to Win: Creating Alternatives for High School Graduates IACMI supports industry workforce needs 100 2,000 9,000+ Internship

IACMI-The Composites Institute - IACMI... · IACMI-The Composites Institute ... Vice President Biden announced the IACMI colocation with LIFT in Detroit, ... A supply-chain centric

NATIONAL WIND COMPOSITES TECHNOLOGY CENTER inWIND … · Mark Kirk, Wind Energy Market Manager, Composites One Derek Berry, IACMI Wind Technology Area Director and Senior Wind Technology

Mold Mold. Molda growing problem Introduction Mold Litigation is increasing Mold Litigation is expensive Contractors are target defendants.

NATIONAL WIND COMPOSITES TECHNOLOGY CENTER inWIND … · Derek Berry, IACMI Wind Technology Area Director and Senior Wind Technology Engineer, NREL Bryan Dods, Chief Executive O˜cer,

Composites One & The Closed Mold Alliance Present …...· Equipment & Fittings for VIP (MVP) · Now What – Next Steps · Composites One Value Proposition Demo: Hands-on and instructor

Engineering Polyurethanes – RIM Part and Mold Design Guide...Parameters Elastomers Rigid Rim Composites Solid Bayflex System (Unfilled) Foamed Baydur System Solid Baydur GS System

PlastiComp Long Fiber Reinforced Thermoplastic · PDF fileFrom application design and performance analysis, ... ready-to-mold long ﬁ ber composites that provide precisely the ...