Concrete & Brickwork Accessories

Concrete & Brickwork AccessoriesProducts and Information

Welcome to the SITETECH Products Catalogue

Established in 2011 Sitetech supplies quality concrete and brickwork accessories to the Construction and Civil Engineering industries

from its strategically placed warehouses in Dublin and Cork.

Sitetech’s mission is to provide our customers with innovative products and technologies enabling them to improve efficiencies

during the construction process. We do this through building long term relationships with our suppliers thus benefitting from quality

products, quick and reliable service and stable prices.

Sitetech’s experienced sales team has a comprehensive knowledge of the products in our stable and are happy to offer technical

advice and help with queries. We carry almost 1,000 product lines in our extensive product range and this enables us to offer a highly

efficient 24 hour nationwide delivery service.

Sitetech’s philosophy is to work with customers in a professional, personal and flexible manner where we

strive for the highest standards of customer care.

We would very much welcome the opportunity of doing business with you.

Contents

Brickwork Products 1-10

Reinforcement Accessories 11-14

Formwork Products 15-20

Grouts, Chemicals and Sealants 21-24

Concrete Testing 25

Joint Fillers 26

Floor Slab and Groundworks 27-28

Reinforcement Connections 29-30

Waterproofing, Waterstops and Gas Proofing 31-35

Paving and Decking Supports 36

Brickwork Products

call on Dublin 01 4013008 Cork 021 4355255

e [email protected] w www.sitetech.ie1

Ancon ST1 Type 1 Wall Tie (Masonry Heavy Duty)

Tie Length Cavity Width

200mm 50mm - 75mm

225mm 76mm - 100mm

250mm 101mm - 125mm

275mm 126mm - 150mm

300mm 151mm - 175mm

325mm 176mm - 200mm

350mm 201mm - 225mm

The Ancon ST1 is suitable for cavities from 50mm to 225mm and can be used for all types of buildings of any height. The section that spans the cavity has a series of holes to provide water drips, to allow the same tie to be used in insulated cavities as well as open cavities.

Benefits• Specially designed safety ends provide excellent

mortar key and reduce the risk of injury on site• Manufactured from corrosion resistant

stainless steel

Staifix RT2 Type 2 Wall Tie (Masonry General Purpose)

Tie Length Cavity Width

200mm 50mm - 75mm

225mm 76mm - 100mm

250mm 101mm - 125mm

275mm 126mm - 150mm

The Staifix RT2 is a general purpose tie suitable for cavities from 50mm to 150mm and can be used for domestic houses and small commercial buildings up to 15 metres in height. The Staifix RT2 is CE marked and can be used in line with NHBC standards. The measured dynamic stiffness of <113MN/m3 meets the performance requirement of Approved Document E for use in external masonry walls.

Benefits• Specially designed safety ends provide excellent mortar key, reduce the risk of

injury on site and prevent tangling• Clear, easily distinguishable packaging makes choosing different types of wall tie

on-site easy• Manufactured from corrosion resistant stainless steel, whilst the high tensile wire

minimises thermal loss through cold bridging

Ancon IHR Head Restraints

Ancon Head Restraints provide the necessary restraint to the top of masonry walls. They allow for vertical movement to accommodate shrinkage or thermal movement of the wall or structural frame, while restraining wind loads.

Benefits• Accommodates vertical movement at

the top of masonry panels• Available in a variety of head options • Standard IHR suits a 215mm high block

Brickwork Products



Masonry Support

Structures with brick or stone cladding will usually necessitate the use of a stainless steel support system for the masonry. Frame type, differential movement, type of cladding, masonry load and cavity width all need to be considered when selecting the most appropriate fixing solution.

AnconOptima and Ancon MDC Bracket Angle Support Systems create a continuous length of angle to support the outer leaf of masonry. AnconOptima is a standard system where the brackets and angles are supplied as separate components. Ancon MDC systems have brackets welded to the angle and are designed to suit the specific cavity width and masonry load of a project.

Benefits• Optimal system design minimises material content and cost• Project management services available through build process• Optional thermal breaks available• Suitable for use with NEXUS pre-fabricated brick slip soffit units

Nominal Length Maximum Angle (incl. 10mm gap Fixing Bracket Unfactored Load Length between angles) Zone Position System (kN/m) (mm) (mm) Colour (mm)

AnconOptima 10 10 990 1000 Red 500 centres

AnconOptima 12 12 990 1000 Green 500 centres

AnconOptima 14 14 790 800 Blue 400 centres

Windposts

Ancon Windposts are designed to span vertically between floors to provide lateral support for panels of brickwork. Windposts can be installed into either the inner leaf of blockwork or into the cavity leaving the blockwork undisturbed. They are designed to suit specific applications and are supplied complete with end connections and ties.

They are suitable for use where standard ladder type masonry reinforcement is inadequate or when there is a requirement to split a large masonry panel.

Benefits• Range of stainless steel profiles available• Designed to suit specific applications• Supplied complete with end connections and wall ties

Brickwork Products

Remedial Wall Ties - 9mm CD Tie

1 2 3

1. DRILL pilot hole of appropriate diameter using a light percussive hammer drill. Stop drill rotating prior to drilling the remote wall layer to prevent ‘whipping’.

2. Insert 9mm ø Thor Helical wall tie into SDS support tool and DRIVE the tie into the masonry using a lightweight roto-hammer drill.

3. Once tool recesses the tie beneath the wall face FINISH by disguising entry bore with suitable filler compacted around the ties driving shank portion.

DESCRIPTION

Remedial wall ties are designed by Thor Helical to have longitudinal blades with sufficient reactive interface angle to cut an accurate self tapping penetrative path into a wide variety of masonry elements upon being driven by a series of axial impacts.

The CD wall tie has a circumscribed diameter of 9mm and is typically driven into a tiny pilot hole to minimize disturbance to the masonry as installation proceeds at remarkable speed and great simplicity.

n Reliable in all types of masonry

n Robust & corrosion free

n Engineered product upgrade

n Patented helix consistency

BENEFITS

The mechanical interlock anchorage of the Twistfix helical wall tie exerts no expansive stress, does not rely on adhesion and is not affected by temperature extremes or fire.

The cross sectional profile of the spiral wall tie includes a wide portion, to maximise grip, and narrow portion, to accommodate differential movements in all directions. The deep and continuous helical troughs prevent migration of water across the cavity.

When under load, the continuous helical blades interact with the host building material to impart an accumulative cone of forces at tangential angles to the helix. Loads are spread evenly along the full penetrative length of the tie to ensure reliability of connection in a wide variety of construction materials.

n Rapid cost effective installation

n Precise helical interlock anchorage

n Combines axial strength with flexibility

n Stable, reliable & unobtrusive



Brickwork Products



Frame Cramps

Frame Cramps are an ideal solution where a restraint is required between masonry and in-situ structures. They can be fixed to concrete, steelwork or masonry. They are available with an integral drip for use across a cavity and either have a single 7mm diameter hole (SDB) or an 8mm x 30mm vertical slot (SDV). The Ancon SPB has a plain shank.Cavity Range SDB/SDV Length (mm) (mm)

20-44 100

45-69 125

70-94 150

95-119 175

120-144 200

145-168 225

170-194 250

195-219 275

220-244 300

Ancon M6 single expansion bolts are recommended for fixing to concrete and M6 set screws or SDTSS-38-5PT self-drilling screws for fixing to steelwork. Frame cramps can be fixed to masonry with suitable plugs and screws or resin anchors.

Ancon HiT (Hammer-in Tie)

The Ancon HiT fixes masonry to concrete, dense blocks (≥7N/mm²), non-perforated brick or hard stone. Use of the HiT can reduce the variety of tie lengths required on site and speed the rate of construction.

Once the plug is installed in the concrete, the Ancon HiT is inserted into a special installation tool, leaving its threaded end exposed. The tool is hammered until it is flush with the concrete, locating the thread in the plug. A neoprene ‘O’ ring must be installed on the tie to prevent moisture crossing the cavity. Using the same tool and ensuring adequate embedment is achieved in the outer leaf, the tie is bent parallel (85-90°) to the brickwork.

The Ancon HiT meets the requirements of PD 6697 as a Type 2 tie.

Lengths: 310mm for any cavity width up to 150mm.

AMR Masonry Reinforcement

Ancon AMR ‘Ladder Type’ masonry reinforcement is a fabricated steel component that is located in the bed joint to strengthen masonry panels without thickening the wall. The longitudinal steel wires are flattened to ensure good mortar cover even when lapped or used with wall ties. Cross wires are welded in the same plane as the main wires at 450mm centres. AMR is available in various wire diameters and widths to suit a range of applications. Manufactured in lengths of 2700mm.

AMR Width Wall Thickness

60mm 100-125mm Brick/Block

100mm 140-150mm Block

150mm 190-200mm Block

175mm 215mm Block

Benefits• Available in five wire diameters• Stainless steel option suitable

for all applications• Fabricated corner sections

available• Ancon AMR-CJ available for

collar-jointed walls

Brickwork Products



Crack Stitching Kit

Staifix-Thor Helical Crack Stitching Kit is a high strength, non-disruptive solution for the permanent repair of cracked masonry.

The kit contains all the necessary components to permanently repair vertical or stepped cracks in masonry. Experts in the remedial market have designed the kit’s contents, guaranteeing the correct specification of reinforcing bar, grout and installation tools required for the application.

Benefits• On completion, the bars and the grout are concealed,

retaining the original character of the wall • Cracks are repaired with no further damage to the wall• No inconvenience to the building’s inhabitants• No costly or lengthy re-construction works

Staifix Universal Wall Starter System

The Staifix universal wall starter system includes all necessary fixings to join a single skin of masonry, 2400mm high, to an existing wall. Each pack includes two fixing strips, five plugs, five washers, five screws and ten wall ties.

Benefits• Suitable for wall widths from 60mm to 250mm • Wall ties slide within the fixing strip to course with

the bed joints of any masonry unit• Ideal for conservatories, extensions and garden walls

36/8 Wall Extension System

This wall extension system is available as a kit comprising a length of 36/8 channel 2400mm long, ten safety-ended SP36 flat wall ties and ten plugs/screws. Where some longitudinal movement must be accommodated at the joint, PP36 ties complete with debonding sleeves are avaliable.

SP36 PP36

Brickwork Products



Ancon Teplo-BF Basalt Fibre Ties

The Ancon Teplo-BF is suitable for cavities from 50mm to 450mm and is manufactured from pultruded basalt fibres. This material has a thermal conductivity of only 0.7W/mK which can be shown in U-value calculations to reduce insulation thickness and wall footprint.

The Ancon Teplo-BF range comprises Teplo-BF1 (Type 1), Teplo-BF2 (Type 2), Teplo-BF3 (Type 3) and Teplo-BF4 (Type 4). Decreasing wall tie centres can increase performance level e.g. Type 3 to Type 2. Contact us for more information.

The Ancon Teplo range has BBA approval and can be used in line with NHBC standards. It also meets the performance requirement of Approved Document E for use in external masonry walls. For internal separating walls of new-build attached dwellings use HRT4.

Available PD6697 Tie Length Cavity Width Tie Types

200mm 50mm-75mm 1, 2 & 4

225mm 76mm-100mm 1, 2 & 4

250mm 101mm-125mm 1, 2 & 4

275mm 126mm-150mm 1 & 2

300mm 151mm-175mm 2

325mm 176mm-200mm 2

350mm 201mm-225mm 2

375mm 226mm-250mm 2

400mm 251mm-275mm 2

425mm 276mm-300mm 2

450mm 301mm-325mm 3

475mm 326mm-350mm 3

500mm 351mm-375mm 3

525mm 376mm-400mm 3

550mm 401mm-425mm 4

575mm 426mm-450mm 4

Benefits• Moulded safety ends offer improved buildability and mortar bond

strength, making it more user-friendly and suitable even in slow drying lime mortars

• Minimise heat loss through thermal bridging

The Ancon 25/14 channel system is designed to tie masonry cladding to an in-situ structural frame, through a layer of insulation. It is suitable for use with steel, timber or concrete frames and any type of insulation. It has been independently tested and is CE marked to EN 845-1.

25/14 channel is supplied in lengths of 2700mm and 3000mm, and features pre-punched holes alternating at 5.3mm and 9.5mm diameters to accept fixing types for fixing to steel/timber (self-drilling HT high thread fixing screws) or for fixing to concrete (CFS fixing screws). When fixing to concrete or through flexible insulation into steel/timber, an Ancon Compression Sleeve is required around the screws. Fixings are available for use with an insulation depth of up to 186mm (timber), 220mm (steel) or 267mm (concrete).

Ancon recommends SD25 wall ties achieve a minimum embedment of 55mm in the masonry. They are available in lengths from 100mm to 300mm to suit open cavities up to 259mm.

Benefits• Suitable for steel, timber and concrete frames• Restrains masonry leaf through any

type of insulation• System comprises channels, wall ties and all fixings

Ancon 25/14 Restraint System

Brickwork Products

DPC Accessories

Sizes

100mm x 15m 100mm x 10m 50mm x 10m

Sizes Pack Qty

25 x 3mm x 2m 20

Sizes

Firtree fixings (for insulation) 6 x 40mm Hammer fixings

Cavity Tray

Adjustable stepped cavity trays for brickwork are used for the following applications.

• At the abutment of a pitched roof with a cavity wall

• On external walls – not exceeding 120mm thickness – built from standard brickwork or similar sized components with regular course heights, including mortar of approx. 75mm

• On roof pitches of 25 degrees and above• Cavity widths of between

50mm – 110mm

Advantages • 195mm high back upstand • Adjustable upstand to cover

50mm – 110mm cavities• Roof pitch marks on tray upstand

to give installation guidance• Cavity tray builds to outer leaf

only to speed up installation and allowing both inner and outer leafs to be built independently if required

• BBA approved

Insulated Cavity-Closer

Advantages• Provides an effective DPC and thermal barrier between frame,

inner and outer wall leaf• Exceeds the minimum thermal resistance path of 0.45m2K/W

stipulated in Robust Details ‘limited thermal bridging and air leakage’• Rigid profile extrusion• Integrated and flexible water strip to reduce air leakage• Simple on-site trimming to cope with ‘rogue’ cavity widths• Can be built in with PVC ties as brickwork progresses or simply nail to block• BBA Approved

n DPC Fixing Strip n DPC Fixing Pins n DPC Jointing Tape

Sizes

2.4m lengths 50 - 100mm, 5 lengths per pack 100mm+ cavities available



Brickwork Products

Rytweep Weep Vent

Sizes

101 x 66 x 10mm

Colours

Clear, Terracotta and Buff/Sand

An unobtrusive cavity weep hole duct. Virtually unseen when installed, showing only the small weep outlet.

Advantages• Simple design for quick and

easy fitting with no special brickwork required

• Flush face• Lugs aid mortar adhesion

for efficient installation• BBA approved

Advantages• Extension for Rytweep and to allow

rendering• Flush face• cut to required size

n Tuben Weep Vent

Sizes

500 x 6mm

Units per box

200

Underfloor & Through Wall Venting

High performance venting may be used instead of a conventional airbrick.

Attachments• Telescopic Under

Floor Vent• Cavity Sleeve• Horizontal Front Extension• Vertical Extension Piece• Duct Adapter• Horizontal Rear Extension

Sizes (Air Brick)

69 x 215 x 60mm Available in a range of colours

Available with a range of attachments.

Mortar Tubs

• Capacity: 1/3 cubic metre (333L) • Internal length: 913mm (at top),

835mm (at bottom) • Internal width: 601mm (at top),

552mm (at bottom) • Internal height: 675mm • External height: 690mm • Tare Weight: 25kg • Safety Factor: 5.1* (Based on a 800kg

nominal static load)



Brickwork Products

Cavity Fire Socks

GIS Cavity Fire Socks are designed to suit both Masonry/Blockwork and Masonry/Timber frame construction applications. GIS Cavity Fire Socks are designed to prevent the spread of flames and smoke as well as reducing the spread of sound along the cavity. GIS Cavity Fire Socks are designed to meet current fire and building regulations and are rigorously tested to current accreditation and provides up to 4 hours fire integrity.

GIS Cavity Fire Socks are 1200mm long and are manufactured from Knauf ECOSE™ Mineral Wool and are encapsulated in recycled plastic.

GIS DUO SOCK TECHNICAL DATAFIRE

GIS Cavity Fire Socks are manufactured using Knauf ECOSE Rock Slab which has a fire classification of EUROCCASS A1 tested to BSEN13501-1 which is encapsulated in recycled plastic which will not add to the propagation of a fire. All GIS Cavity Duo Socks are tested in application to BSEN1366-4 as was BS476: Part 20 using current fire test methods. Tested for cavities up to 300mm wide both Vertivcal & Horizontal uses test report BMT/FE/IF/15078

ACOUSTICS

GIS Cavity Fire Socks meet the generic requirements for the prevention of flanking noise transmission, along external and separating wall cavities. Meeting approved document E (2014)of the building regulations, for England, Wales & Ireland. (based on width range for application 100mm/200mm/250mm/300mm or 450mm wide.

THERMAL

GIS Cavity Fire Socks have a thermal conductivity of 0.037W/mK and when fitted will provide an effective perimeter edge seal as stated in building regulations L1A and L2A as well as meeting section 6 of the Scottish building standards.

Cast-in Channels

Cast-in channels provide the necessary adjustment when fixing masonry support systems to concrete and eliminate the need for site drilling.

Ancon 30/20Ancon 30/20 is a high performance cast-in channel and provides cost benefits over 38/17 channels. The unique shape allows the applied load to be fed directly from the channel lips to the anchors and the more compact section size improves its fit between reinforcement. Specially designed T-head bolts ride up the sloping sides of the channel and securely lock behind the front lips.

It is filled with continuously extruded closed-cell PE-LD foam. This material is removed easily in long sections and is 100% recyclable.

Preferred ‘T’ Bolt Tightening Other Preferred StainlessChannel Standard Length Torque Size Lengths SteelReference Bolts (mm) (Nm) Bolts (mm) 304 316

30/20 M12 50, 90 50 - 100, 150, 3000 Y N

38/17 M12 50, 100 30 M16x50 100, 150, 3000 Y Y

Ancon 21/18Ancon Omega 21/18 channel is a high performance, self-anchoring, cast-in channel for use with Ancon wall ties referenced _ _ 21 to provide necessary restraint to the outer leaf of masonry. The shallow depth of 18mm allows the channel to be used where there is reduced cover to the reinforcement and concrete as thin as 75mm.

The 21/18 channel is available in 100mm and 3000mm lengths with nail holes to aid the fixing of the slot to timber formwork. The channel is filled with polystyrene to help prevent the ingress of concrete.



Brickwork Products

Roll Size (m) 50 x 1.37

Size (m) 4 x 25

Size 2m x 1m x 2mm

Hessian Rolls for frost protection and curing of brickwork & concrete.

Hessian Rolls (Frost Protection) Temporary Protective Sheeting

Corrugated Protection Board

Also available as fire retardant.

Visqueen Zedex CPT high performance DPC & cavity tray system is manufactured from co-polymer thermoplastic (CPT) providing all the characteristics necessary for it to perform effectively for the lifetime of the building in which it is incorporated.

Visqueen Zedex CPT DPC

n Outperforms all other high performance flexible DPCsn Contains no hazardous pitch or PVC plasticizersn Excellent tear resistance under high compressive loadsn Low permeability to Radon and Carbon Dioxide gases

Width Length m2/Roll (mm) (m) 100 20 2 150 20 3 225 20 4.5 300 20 6 450 20 9 600 20 12 900 20 18 1000 20 20

Visqueen Polythene DPC

Width Length m2/Roll (mm) (m)

100 30 3 150 30 4.5 225 30 6.75 300 30 9 450 30 13.5 600 30 18 900 30 27

Polythene DPC provides a cost effective and durable DPC.

Pic To Come

10


e [email protected] w www.sitetech.ie

Reinforcement Accessories

Continuous Wire & Snake Spacer Chairs

n Continuous Wirechairs

Requirements for Laying

For the laying of Chairs a distance of approx.1,000mm between strips is recommended. This corresponds to approx. 1 linear metre per square metre of top reinforcement.

n For bar reinforcement and for fabric sheet reinforcement

n No foreign body in concrete

n Lightweight

n Design in conformity with German DBV guidelines

n Snake Spacers

Height Length Pack Size (mm) (m) (m) 50 2.0 50 70 2.0 50 90 2.0 50 100 2.0 50 120 2.0 50 130 2.0 50 150 2.0 50 160 2.0 50 180 2.0 50 200 2.0 50 230 2.0 40 250 2.0 40 280 2.0 40 300 2.0 40 350 2.0 40

Height Pallet Size Pack Size (mm) (m) (m) 50 3200 50 70 2400 50 90 2000 50 100 2000 50 120 1600 50 130 1600 50 150 1200 50 160 1200 50 180 1200 50 200 800 50 220 800 50 240 800 50 260 600 50 280 600 50 300 600 50 320 400 50 350 400 50 400 400 50

Plastic Shims

Thickness Size Pack Size (mm) (mm) (No.) 2 70x70 250 3 70x70 250 5 70x70 125 7 70x70 125 10 70x70 250 20 70x70 150

Tying Wire

Supplied as:

Soft black annealed wire

Stainless Steel Tying Wire

Supplied as:

1.2mm diameter

Plain Squares




KSN Anchors

Ancon KSN Anchors, in combination with Bartec Plus parallel-threaded reinforcing bars, simplify rebar continuity at wall-to-slab construction joints. The internally-threaded anchors are simply cast into the wall and, during construction of the adjoining slab, accept continuation bars prepared with a Bartec Plus parallel-thread.

Benefits• Quicker, easier, and safer than

re-bend continuity boxes• No on-site bar straightening

required• Virtually no restriction on

continuation bar length• Approved by CARES (TA 5061)

DSD Shear Load Connectors

Ancon’s range of shear load connectors offers significant advantages over plain dowel bars. They are more effective at transferring load and accommodating movement and, due to their two-part construction, are simpler to install. The sleeve component is nailed to the formwork and cast with the first pour; drilling of either formwork or concrete is not required. Once the formwork is removed, the dowel component is pushed into the sleeve and cast with the second pour.

• The Ancon DSD is the original two-part, double dowel, shear load connector. The dowel component can move longitudinally within the sleeve to accommodate movement

- Available in ten standard sizes and can transfer design loads from around 20kN to over 950kN- Larger connectors can be used in joints up to 60mm wide

• The Ancon DSDQ shear load connector uses the same dowel component as the Ancon DSD, but the cylindrical sleeve is contained within a rectangular box section to allow lateral movement in addition to the longitudinal movement

- Nine standard sizes can be used to transfer design loads from around 30kN to over 950kN.

• The Ancon ESD is a single dowel shear connector available in four sizes, with each size available in two lengths. Ancon ESD shear connectors are used where the slab or wall is too thin for Ancon DSD, and where loads are small.

Shearfix Punching Shear Reinforcement

Benefits• Suitable for all column shapes and locations• Easy to install either ‘top down’ or ‘bottom up’• Holds UK CARES Technical Approval• Eurocode 2 design program available

Ancon Shearfix is used within a slab to provide additional reinforcement around column heads. It is the ideal solution to the construction problems associated with punching shear, including enlarged column heads. The system consists of double-headed studs welded to flat rails, positioned around the column head or base. The shear load from the slab is transferred through the studs into the column. The studs are welded to the rail at centres determined by Ancon’s software.

5017TECHNICALAPPROVAL




Continuous Plastic Chair

Cover Pack Size Pallet Qty (mm) (m) (m) 20 100 4800 25 100 4200 30 100 3600 35 60 2400 40 60 2160 50 60 1440 60 40 960

Supplied in 2m lengths.

Plastic Mesh Spacers

Cover (mm) Pack Size (No.) 25/30 250 40/50 250 70/80 200 90/100 100

Continuous ISO Chair

Cover Pack Size Pallet Qty (mm) (m) (m)* 20 100 4800* 25 100 4200 30 100 4200* 35 60 2880 40 60 2400* 45 60 2100 50 60 1440* 60 40 1600* Special Order


Zig Zag Spacer

Cover Pack Size Pallet Qty (mm) (m) (m) 20 100 5000 25 100 5000 30 100 5000 35 80 3200 40 80 3200 50 80 3840 60 82 3280


Plastic Wheel Spacers Cover (mm) To Suit Bar (mm) 15 4-12 20 8-12 25 8-12 25 12-20 30 8-12 30 12-20 35 8-12 35 10-20 40 8-12 40 12-20 50 8-12 50 12-20 60 12-20 75 12-20

Rebar Protection Caps

Rebar Safety Strip

Sizes:

Supplied in 1m lengths

Bar Size (mm) Pack Size (No.) 8-16 250 16-32 250




Chamfer Edge Profile - Radius

Height (mm) Pack Size (m) 21 100

Void Formers

Dimensions Length (mm) (m) 20 x 10 3 20 x 20 3 25 x 12 3 25 x 25 3

Chamfer Edge Profile - Plain

Chamfer Edge Profile - Nail Flange

Height (mm) Pack Size (m) 11 100 15 100 20 100 25 50 40 50

Height (mm) Pack Size (m) 11 100 15 100 20 50 25 50

Cover Length Pallet Qty (mm) (mm) (No.) 40 1000 500 50 1000 400 60 1000 250 75 1000 175

Concrete Triangular BarConcrete Square Bar

Cover Length Pallet Qty (mm) (mm) (No.) 40 1000 300 50 1000 250 60 1000 150 75 1000 100

Triple Cover Concrete Spacer

Double Cover Concrete Spacers

Cover (mm) Pack Size (No.) 20/25/30 500 35/40/50 200

Cover (mm) Pack Size (No.) 25/30 500 30/40 250 40/50 200 60/75 50



Formwork Products

K-FORM Screed RailsThe Innovative, Recycled, Time & Money Saving,uPVC Sacrificial Screen Rail System

FEATURESn Enables adjoining bays to be poured

simultaneously

n ‘Click-together’ ease

n Pre-drilled holes for dowel bars

n Pre-drilled holes in base for anchoring

n Manufactured in durable 100% recycled uPVC

n Removable top strip to allow joint sealing

n No removal after use

n Designed for pours of 50mm-225mm thick

K-FORM UPVC Screed Railing provides the construction industry with an economical, efficient and environmentally friendly alternative to steel and timber formwork.

Made from 100% recycled materials, K-FORM is lightweight, durable and does not require removal after placement of concrete. It is easily cut to length on site and has pre-drilled holes in the vertical face for placing steel dowels bars and in the base for anchoring. K-FORM’s patented design features a removable top strip for joint sealing and its unique end clips allow for quick and easy installation.

R

155 mm

85 mm

3000 mm

10 mm

(2.8m in length forexport outside of UK)

24 mm holes pre-drilled at 300 mm centresfor dowel bars.

Eight holes drilled at 800mm intervals (four per side) to aid anchoring with mortar.

K-FORM K85 Screed Railfor Slab thickness 100mm - 140mm

155 mm

35 mm

3000 mm

10 mm

Removable top strip Eight holes drilled at 800 mm intervals(four per side) to aid anchoring with mortar



3000 mm

155 mm

135 mm

10 mm


24 mm holes pre- drilledat 300 mm centresfor dowel bars to suit150 mm -225 mm depthpours of concrete


Removable top stripRemovable top strip


155 mm

85 mm

3000 mm

10 mm





155 mm

35 mm

3000 mm

10 mm




3000 mm

155 mm

135 mm

10 mm






155 mm

85 mm

3000 mm

10 mm





155 mm

35 mm

3000 mm

10 mm




3000 mm

155 mm

135 mm

10 mm








Formwork Products

Tierod - Weldable Anchors

Tierod - Plastic Sleeves

Waterproof Cone and Cap

One Piece Waterproof Sleeve

Tierod - Plastic Cones

Cone:

Cap:

Size Dims Weld Seam (mm) (mm) Required (mm) 15 130x50 4

To Suit Size Pack Bar (INT/EXT) Size (mm) (mm) (m) 15 22/26 100 20 26/30 50

Size (mm) Pack Size (No.) 14 1000 20 500 22 500 26 250

22/50 125 – also available in spiral 26/50 125 – also available in spiral

Size (mm) Pack Size (No.) 22 500 26 250

Pack Size (No.) 22 500 26 250

All in 2m lengths.

Tierod - Connectors

Bar Size (mm) Length (mm) 15 30x105 20 40x130 26.5 50x150

c/w centre-pin stop.

Cone Removal Key to suit.

For Wall Tickness (mm) Pack Size (No.) 200 100 225 100 250 100 300 100 350 100 400 100 450 50 500 50



Formwork Products

Hydrophilic Sealing Plug - Tested to withstand 6 bar water pressure

1 2 3

Tierod - Rubber Stoppers

Tierod - Hex Nuts Round Wire Nails

Bar Size (mm) Size (mm) 15 30x50 20 36x60 26.5 46x120

Size (mm) Pack Weight (Kg) 50 25 65 25 75 25 100 25

Size (mm) Pack Size (No.) 22 500 26 250

Tierod - Cast In Anchors

Bar Size Type Length Fail Load (mm) (mm) (kn) 15 Cast-in-anchor 95 90 15 Form Anchor 130 100 15 Plastic Anchor 70 50

Bar Size Type Pack Size (mm) (mm) (No.) 15 120x120x10 Pressed 25 20 120x120x20 Plain 20 26.5 130x130x35 Plain Singles

Tierod - Waler Plates



Formwork Products

Stopend Permanent Formwork

Gaffa Tape

Permanent Formwork

Thickness Length Width (mm) (mm) (mm) 0.4 2000 445 0.4 3000 445

Supplied in Widths (mm) 50 75

Width Length Thickness (m) (m) (mm)

2.0 4.5 8 2.4 2.5 8

A fast & simple system for constructing concrete ground beams.

Formabeam is manufactured from extruded twin-wall poly-propylene sheeting and is 100% recyclable.

Advantages:

• Quick and simple to install

• Tailored to site requirements

• Saves labour and time on site

• Supplied on short lead times

• Minimises concrete wastage



Formwork Products

Metal formworkNEWInnovativePRODUCT

The metal formwork is quickand easy to install

The ideal formworkfor cast floorconstruction

• Available for various floor heights

• Lightweight, easy placement

• Quick and easy to install

• Instant straight floor edge

• Striking is no longer required!

Also available:

• Universal corner pieces: for inside and outside corners

• In combination with quick-acting tensioners: quick and straight installation



Formwork Products

Column Formers

Tube I/D Tube Wall Maximum Pour Concrete Weight (mm) Thickness (mm) Height (mtr) Required (m3/mtr) (kg/mtr) 150 2.80 6.0 0.018 1.24 200 2.80 6.0 0.031 1.63 240 3.20 6.0 0.045 1.96 250 3.20 6.0 0.049 2.08 300 3.20 6.0 0.071 2.38 350 3.70 6.0 0.096 3.09 400 4.10 6.0 0.126 3.52 450 4.10 6.0 0.159 4.50 500 4.60 6.0 0.196 5.44 550 4.60 6.0 0.237 5.99 600 5.00 6.0 0.283 6.53 650 5.00 4.0 0.332 7.16 700 5.00 4.0 0.385 7.71 750 5.00 4.0 0.442 8.26 800 5.50 4.0 0.502 8.81 850 5.50 4.0 0.567 9.36 900 5.50 4.0 0.636 9.91 950 5.50 4.0 0.708 10.46 1000 5.90 4.0 0.785 11.11 1100 5.90 4.0 0.950 12.11 1200 5.90 4.0 1.130 13.21

Plastic Kickers

Diameter Height Pack (mm) (mm) Size 48 30 100

Plastic Kickers are used to locate the formwork panel at the base of walls. They are positioned using a masonry nail which is included.

Grout Check Foam

Width Roll Length Box (mm) (m) (Qty) 12x6 10 25 rolls 24x12 5 12 rolls

Tierod -Wing Nuts

Tierod - RockAnchors

Tierod - WaterBarrier Nuts

Size (mm) Pack Size (No.) 15 100 20 50 26.5 Singles

Size (mm) Length (mm) Drill Size 15* 130 35-37 20 125 41-43 26.5 135 51-53

Bar Type Length Disc (mm) (mm) (mm) 15 Flanged 110 65

Sizes: 26.5mm upwards supplied as a load bearing hex nut.

*Minimum Embedment Depth 230mm.



Grouts, Chemicals and Sealants

Non Shrink Grout Repair Mortars

Release Agents

Sizes: Pack Size 25kg



Curing Agent

Sizes: Pack size - 205 litre and 25 litre

n Aids the efficient curing of concrete for use on external slabs, walls and flooring

n Levelling new and old concrete surfaces, infilling surface imperfections

n Making good concrete blow holes, filling small holes

n Making good frost damaged and scoured concrete surfaces

n Levelling of patched concrete repairs

n Grouting under stanchions and baseplates

n General void fillingn Fixing balustrades, starter bars

and barriersn Underpinning

Floor Levelling Compound

Used for levelling out uneven floors prior to the laying of:

n Carpetsn Carpet tilesn Vinyl tilesn Rubber tilesn Thermoplastic

tiles n Linoleumn Wood block

flooring

n A specifically formulated system designed to give maximum protection to all types of formwork and to help ensure production of high quality concrete


Polyester Anchor Grout


Polyester Anchor Grout is a two-component polyester resin and special catalysed filler that has been developed for anchoring and fixing. The gel-like nature of the thixotropic grout is ideal for anchorage of wall and soft fixings for use on:

n Anchorage of bolts and fixings to building and civil engineering work

n Anchorage of rebar starter barsn Installation of cavity wall ties in

brickwork n Fixings to masonry structuresn Anchor dowel bars to

pavements and slabsn Fixings to walls and soffits




Sika 4aFive Star Grout

Sizes: Pack Size - 5kg

Sizes: Pack Size - 25kg

Used for

n Water cut-off in tunnels, sewers and basements

n Tanks, wells and minesn Sealing around pipes and other

fixtures in concrete and masonryn Benching manholes

Top Face Retarder

Mould Face Retarder

Epoxy Mortar

SBR Liquid


Sizes: Pack size - 25 litre

Sizes: Pack Size - 5 litre and 25 litre

Epoxy Mortar consists of epoxy resin, hardner and selected graded aggregates (filler) which when mixed produce a high strength, impermeable and chemically resistant mortar.

Epoxy Mortar has negligible shrinkage characteristics plus high adhesion, making the product ideal for all types of concrete repair including repairs to:

n Precast unitsn Spalled and cracked concrete

structuresn Floors and other substrates

where chemical resistance and/or impermeability to water, oil, petrol and many chemicals is required

n Beamsn Runway lightsn Bridge bearings

Five Star Grout is a premixed cementitious grout developed for applications where an economical grout with good flow and strength is required.

Top Face Retarder is an aqueous liquid suitable for either spray or watering can application. It retards the set of the surface cement matrix of freshly cast concrete for easy removal.

Mould Face Retarder is a transparent aqueous composition with a gel consistency colour tinted to assist application.

Adoplug

Coverage: 2kg - Approx. 1m2 by 1mm depth

ADOPLUG is a multi-functional polymer modified, fibre reinforced, water resistant, high strength, chemical resistant, cementitious powder designed specifically for internal coating and repair of cement and concrete based surfaces, for the plugging of tie holes and for general surface repair.

SBR Liquid is a styrene butadiene emulsion used to make polymer mortars, screeds and renders. It can be mixed with cement as a bonding grout for screeds and renders. The improvements allow the production of high strength screeds, thin section screeds, patching/repair mortars and waterproof mortars.

ExpandingFoam

An easy to use filler for holes, voids, etc.

Sizes: 750ml can




LamposilixMBM 60

Ultra-fast setting and curing hydraulic binder for stopping water leaks.

WHERE TO USEFor instant stopping of water leaks, even water under pressure.

n Stopping water leaks in basements, subways and below grade structures in general.

n Stopping water leaks in tanks above ground.

n Waterproof sealing of rigid joints between walls and floor slabs.

n Waterproof sealing of cracks and holes.

MBM 60 is a single component, rapid strength bedding mortar suitable for the installation and reinstatement of all types of access covers, as well as bedding kerbs and emergency repairs. It is manufactured from a controlled blend of specially selected aggregates, cements and additives and only requires the addition of water to produce a high quality bedding layer which can be trafficked after just 1 hour.

Sizes: Pack size - 5kg

Sizes: Pack size - 25 Kg

Quickset

Quickset is a blend of specially selected aggregates, cements and additives to give a very fast setting cementitious patching screed mortar with high early strength. Rapid repairs can be carried out on screeds, pavements and factory floors with minimal obstruction and downtime. Quickset can be used for other rapid setting manhole covers, etc. Quickset is chloride-free, sulphate resistant and non-corrosive to reinforcing steel and generally does not require a bonding agent.


Ultraplan Renovation Screed


Ultraplan Renovation Screed is a re reinforced self levelling compound, designed for use in the refurbishment of existing floors in both commercial and domestic applications, it can be hand or pump applied.

Used for interior levelling, smoothing and removing differences in thickness from3 to 40 mm on new or existing concrete, screeds, stone, terrazzo and ceramictiles, old and new timber oors, oor boards, chipboard panels, plywood, parquet.

Ultraplan Renovation Screed is suitablewhere good resistance to loads isrequired, also for wheelchair trackand underoor and undertile heatingsystems.

Used for levelling out unevenfloors prior to the laying of:

n Carpetsn Carpet tilesn Vinyl tilesn Rubber tilesn Thermoplastic tilesn Linoleumn Wood block flooring




The top class plastic device.Oil resistant on construction.Compression Sprayers.

n Professional pumpn Integrated dirt filtern Ergonomic shut-off valve

Mapefix PE SF Chemical Anchor

Width (mm) Pack Size (m) 10 1280 12 762 15 472 20 335 25 182 30 121 40 128 50 73

Line Marking Paint

Sealant Guns

Sizes: 750ml can

Polyurethane Sealant

Sizes: Gun applied grade - 600 ml Pouring grade - 4.0 or 4.5 litres

Polyurethane can be supplied in pouring and gun grades for sealing horizontal and vertical joints where movement is expected, or where the performance specification is too rigourous for more common mastics and joint sealers. It is ideal for use in expansion joints in reinforced concrete structures such as bridges, reservoirs, water treatment works, sea walls and roads, etc. It can also be used in floors subject to heavy usage where a high resistance to damage is required.

Mapefix PE SF is an adhesive for chemical anchoring metal bars in holes made in building materials.

It is a two-component, styrene-free product made from a mixture of polyester resins.

Foam Backer Rod

n Power Pro Sealant Gun

The ultimate heavy duty sealant gun, extra pull trigger, hook end and swivel action barrel for both 310ml and 400ml cartridges.

n Professional Sealant Gun C4

Sturdy skeleton gun with hexagonal rod, re-enforced ring and hook end.

Construction Chemical Sprayer

Sizes: 5 Litre 10 Litre

Larsen Line Marking Paint is a blend of high quality pigments, resins, hardeners and fast-drying solvents, supplied in an easy to use aerosol dispenser. Larsen Line Marking Paint can be applied both by hand as a spot marker or used in conjunction with a line marking applicator.It is available in a range of colours.

Sizes: Pack Size 300ml & 420ml



Concrete TestingCube Mould 4 - part metal

Plastic Moulds

Base PlateFor use with slump cone

ScoopAluminium

Slump Cone

Tamp RodFor use with slump cone

110V Curing Tank 12 cube capacity

Szes (mm) 100 x 100 150 x 150

Thermometers

n Digital Concrete Thermometer

n Plastic Cube Mould

n 2 Gang Cube Mould

n Max-Min Thermometer



Joint FillersPolyjoint Strip/Roll

Code Depth Width Tear off Length Length (mm) (mm) (mm) (strip) (mm) (roll) (m) 100/10/10 100 10 10 2000 10 150/10/10 150 10 10 2000 10 200/10/10 200 10 10 2000 10

150/12/12 150 12 12 2000 10 200/12/12 200 12 12 2000 10 250/12/12 200 12 12 2000 10

100/20/20 100 20 20 2000 150/20/20 150 20 20 2000 200/20/20 200 20 20 2000 250/20/20 250 20 20 2000

Standard density (30kg/m3) polyethylene joint filler complete with perforated tear off strip

Polyjoint Sheets

(mm) (mm) 10 2000x1200 12 2000x1200 20 2000x1200 25 2000x1200

Standard density (30kg/m3) polyethylene foam expansion joint

Full Sheet



Floor Slab and Groundworks

Denso Tape

Bolt Boxes

Width (mm) Length (m) 50 10 75 10 100 10

Length (mm) Pack Size (No.) 229 400 305 300 380 200 457 100 534 100 610 70 762 50

Waxed cardboard

Conical

Base Crack Inducer

Height Length (mm) (m) 40 5 75 5

Dowel Bar Paint

Pack Sizes: 5 ltr Tin and 25 ltr Tub

Frost Blankets

The blanket gives excellent thermal insulation allowing it to keep the concrete warm in the winter and protects it from the heat in the summer

Woodfibre Fillerboard Sheets

Bitumen impregnated woodfibre joint filler

Thickness Sheet Size (mm) (mm) 12 2400x1200 20 2400x1200 25 2400x1200



Floor Slab and Groundworks

Metal Screed Chair

Type Slab Depth Pack Range Size (mm) (No.) 1 120 – 155 1 2 145 – 205 1 3 195 – 305 1 4 295 – 405 1 50 50 – 500 1

Polythene DPM

Gauge Thickness Roll Size (mu) (m) 1000 250 25x4 1200 300 25x4 2000 500 12.5x4

Gauge Thickness Roll Size (mu) (m) 500 125 50x4

Also available: Temporary Protective Sheeting

Bontec NWGeotextile

Type Length Width (m) (m) Woven 100 5.25 Non-woven 100 5.25

SPECIAL ORDER!

Bontec NW is a range of needle-punched and thermally bonded geotextiles that offer the highest levels of engineering performance and quality standards. The NW range is used in various applications including site access roads, hard standings, road and railways, drainage blankets and car parks.

Dowel Bar Sleeves

Bar Size Length Pack Size (mm) (mm) (No.) 12 450 100 16 300 100 20 300 100 25 300 100 32 375 100

Dowel BarsRound mild steel bars

Bar Diameter Length (mm) (mm) 12 600 12 900 16 600 20 600 25 600 32 600

Dowel Bar Caps

Bar Size Length Pack Size (mm) (No.) 12 100 100 16 100 100 20 100 100 25 100 100 32 100 100



Reinforcement Connections



Eazistrip Reinforcement Continuity Systems

Benefits• Allows for simplification of formwork design• Contributes to the acceleration of the construction process• Risk of injury from projecting bars is minimised

Eazistrip is designed to maintain continuity of reinforcement at construction joints in concrete. It consists of pre-bent bars housed within a galvanised steel casing. Once installed in the first concrete pour, the protective cover is removed and the bars are straightened ready for lapping with rebar in the second pour.

5017TECHNICALAPPROVAL

Ancon Starter Bar Coupler

To Suit Rebar T12 T16 T20 T25 T32

The Ancon Starter Bar system is designed to increase the speed of construction at joints where continuity of reinforcement is required, or for fixing applications using standard metric bolts or studding. Use of this Ancon system can simplify concrete design and eliminate the need to drill formwork or concrete.

Reinforcement Connections



Benefits• Available to suit bar diameters from 10mm to 40mm• Approved by HAPAS for highway work • ET series MBT couplers join bars of the same diameter• MBT Transition Couplers for joining bars of different diameters• MBT Continuity Couplers for use at construction joints • MBT Headed Anchors provide dead end embedment

MBT is a range of mechanically bolted couplers for the joining of reinforcing steel. Bars are locked in place within the coupler by a series of lockshear bolts, the heads of which shear off at a predetermined tightening torque to provide a full strength splice and a visual check of correct installation. They require neither bar end preparation nor bar rotation and are suitable for imperial, plain round or deformed reinforcing bars. They are ideal for remedial applications involving the cutting out and replacing of damaged or corroded rebar sections.

MBT Reinforcing Bar Couplers

BBA (16/5300)HAPAS (15/H240)

Balcony ConnectorsAncon Thermally Insulated Balcony Connectors minimise heat loss at balcony locations while maintaining structural integrity. They provide a thermal break by inserting a material with a low thermal conductivity between elements with a higher conductivity and most also provide local insulation at the joint. As a critical structural component, they transfer moment, shear, tension and compression forces. Standard solutions are available for concrete-to-concrete (Isotec) and steel-to-concrete (STC) solutions.

Ancon Isotec is a high performance thermal break system comprising 100% stainless steel reinforcement and fire-resistant mineral wool insulation. Compression studs rather than bars facilitate installation even in congested concrete floor slabs.

Benefits• Suitable for highly energy-efficient structures • Inherent fire and corrosion-resistant properties• Supplied as a unit providing rigidity and

dimensional stability• Range includes standard solutions for stepped balconies

Ancon Isotec

Ancon STC is used for anchoring steel balconies to concrete floor slabs and has been proven through thermal modelling to reduce heat loss when compared to direct connections. The two part assembly, comprising a cast-in anchorage and a post-fixed bracket with thermal pad located at the interface, allows for phased construction. This reduces the risk of the units being damaged during the construction process. Serrated pads and slots provide adjustability in the final bracket position without the need for stop butts or levelling shims.

Benefits• Proven through thermal modelling to reduce heat loss• Two-part phased assembly avoids damage by other trades• Variable bracket projection avoids conflict with cladding• Adjustability offered without levelling shims

Ancon STC

Waterproofing, Waterstops and Gas Proofing

Mapeproof HW Waterproof Membrane

Mapeproof HW’s nonwoven fabric is needlepunched through to the woven fabric, with thousands of fibers mechanically locking the sodium bentonite clay in place. After backfill is placed and confined under pressure, Mapeproof HW hydrates and forms a monolithic waterproofing membrane when exposed to moisture. Mapeproof HW contains zero VOCs and can be installed in most weather conditions as well as to green concrete.

The swelling characteristics of the sodium bentonite clay in Mapeproof HW can seal small concrete cracks caused by ground settlement, concrete shrinkage or seismic action. Mapeproof HW also forms a strong mechanical bond to concrete when the concrete is poured onto the nonwoven geotextile fibers.

n Can be installed over damp or green concrete substrates

n Self-healing if punctured

n Mapeproof HW is not affected if the level of the water table rises and falls.

n The needle-punch pattern in the geotextile fabrics guarantees that the sodium bentonite is held firm and stable, even when Mapeproof HW is applied vertically.

Walldrain

Its dimpled sheet provides outstanding drainage and physical protection over under-ground foundation walls. The nonwoven geotextile mat over the dimples creates a continuous air gap for reliable ventilation and drainage of water inflow from the surrounding soil. This composite system excels in a wide variety of other application sectors as well, including basements, underground parking garages, roof terraces, parking garage roofs, etc., providing users a variety of benefits.

n Permanent air gap, suspended particles in water are filtered out by the geotextile mat

n Excellent drainage performance

n Outstanding compressive strength

Walldrain products are resistant to a wide range of chemicals, impervious to root penetration, rot-proof and unaffected by soil bacteria and fungi.




Plastimul – Liquid Damproof Membrane

Plastimul is a solvent-free paste consisting of selected water-emulsified bitumens, special fine-graded aggregates and additives, manufactured according to a formula developed in the MAPEI Research & Development Laboratories.

WHERE TO USE

n Waterproofing foundations.

n Waterproofing bearing walls.

SOME APPLICATION EXAMPLES

n Cold waterproofing masonry, or concrete poured over bare ground.

n Waterproofing flat or curved surfaces on structures below ground level, such as man-made tunnels and underpasses.

n Waterproofing horizontal concrete structures below screeds isolated with PE sheets (in such cases we recommend applying Mapelastic on the screed before installing flooring to protect the screed).

Mapethene LT – Self Adhesive Waterproofing Membrane

Mapethene LT is a self-adhesive bitumen membrane made from a mixture of bitumen and special polymers bonded to a double laminated film of high density polyethylene (HDPE).

Protection Board

Protection Board is a semi rigid board containing blended bitumens and minerals reinforced with cellulose fibres, heavily compressed. Used to provide protection for waterproof membranes against mechanical damage by backfilling and foot traffic.

Uses: Bituminous Protection Board is designed for use in both horizontal and vertical applications to protect Waterproof membranes against abrasive backfill and poured concrete. They should be butt jointed and supported during backfilling. Mastic or joint filler adhesive can be used to spot bond the board to the membrane. The joints should be staggered and also staggered over the membrane laps.

Mapethene QuickDrying Bitumen Primer

Solvent-free bitumen primer for membranes from the Mapethene line.

ADVANTAGESn Ready to use.n Applied by brush, roller or spray.n Quick drying, Solvent-free.




Masterstop Swelling Tape

General Building SupervisoryTest Certificate

MEDIUM Resistant Non-Resistant Alkalis in general 4

Urea 4

Liquid manure / slurry 4

Biogas 4

Radon 4

De-icing salt 4

Substances obtained by means of fermentation 4

Substances obtained by means of composting 4

Waste water in water treatment plants 4

Petrol 8

Diesel 8

Heating oil 8

Resistance of MASTERSTOP bentonite swelling tapes and MASTERSTOP SK

MASTERSTOP bentonite swelling tapes have a proven track record which goes back many years in construction practise.

They swell upon contact with water and seal cracks or construction joints reliably and permanently.

Test certificates confirm the product’s suitability for various applications.

The convincing advantages of

MASTERSTOP bentonite swelling tapes

n Easy and safe installation

n No foundation curbs

n Self-injecting effect

n The swelling tapes penetrate cracks and cavities

n Enviromnentally friendly

n No fittings or welding

n The swelling and shrinking process is reversible

n Dimensionally stable and not sticky

n No cuttings or oddments

n Safety proved by extensive testing




Foundation/wall connection

Installation with swelling tape adhesive

Installation with fastening grid and nails

Pipe Sealing

Installation of Masterstop at construction site - Size 25/20mm

Installation with swelling tape grid Installation with swelling tape adhesive

InstallationMasterstop bentonite swelling tapes are fixed with a swelling tape grid or swelling tape adhesive.

They are laid inside the reinforcement with a concrete cover measuring 8cm.

Swelling tape grid

Steel nails with washer Masterstop

Size

25/20 and

20/15

Concrete Concrete

Swelling tape adhesive

Masterstop

All sizes




PVC Waterstop

PVC waterstops are extrusions made from high grade PVC resin that are plasticized and stabilized to offer long life performance in concrete structures against water leakages. PVC waterstops are hydrophobic in nature and resist water, all types of hazardous liquids and water borne chemicals. The waterstop profiles are designed so that when embedded into the concrete joint, they form a continuous water tight diaphragm to prevent transmission of water through the joint. PVC waterstops have high flexibility and tensile strength to withstand any shear forces laterally or transversely in the joints. PVC waterstops are manufactured in different thickness, widths and profile types to suit various joints like contraction, expansion and construction joints. The selection of PVC waterstops is made based on the type and the expected movement of the joint together with the hydrostatic head pressure, the concrete structure is going to be subjected to.

Pre-fabricated factory welded joints Accessories

Internal Construction Joint

External Construction JointExternal

Expansion Joint

Internal Expansion Joint

Flat L Flat T Flat X Reverse Vertical L Joining Jig Electric Welding Knife



Paving and Decking SupportsFixed Height Paving Slab Supports

Adjustable Paving Slab Supports

Decking Supports

Adjustable Paving Slab support with adjustable height from min 35mm to max 500mm

Adjustment of the support of 1.5mm for each 90 degree turn

Base unit is 35mm to 60mm with the option of extensions in 25,50 and 100mm

35mm-60mm paving support30 per box

25mm paving support extension30 per box

50mm paving support extension 30 per box

100mm paving support extension30 per box

Fixed Height Paving Slab Supports act as a guide when laying paving thus ensuring uniform position. This saves a considerable amount of time in application and gives an attractive finish.

Fixed Height Paving Slab Supports are 15mm high.



Sitetech Branches

Nationwide supply of concrete and brickwork accessories...

...we offer n Independently run business

nNationwide coverage

nCommitment to the highest standard of service

nAn unrivalled level of expertise & experience

Grants Drive

Grants Avenue

Newcastle RoadGreenogueRoundaboutNewcastle

Roundabout AerodromeRoundabout

College Road

Gran

ts Ro

ad

Co

llege R

oad

Co

llege R

oad

Jord

ansto

wn

Ro

ad

Aerodrome Business Park

Greenogue Business Park

to Rathcooleand M7

to Newcastle

Radisson Hotel

Euro Business Park

Eastg

ate V

illage

N25 to Cork N25 to Rosslare

LittleIslandInd. Est.

To Courtstown

To Wallingstown

To GlounthauneTo Glanmire

NCTCENTRE

Dublin DepotUnit 514, Grant’s Avenue,

Greenogue Business Park, Rathcoole, Co. Dublin.D24 EH21

+353 (0)1 401 3008 [email protected]

Cork DepotLittle Island Business Park,

Little Island, Co. Cork.T45 YE36

+353 (0)21 435 5255 [email protected]

Date post:	24-Oct-2021
Category:	Documents
Upload:	others
View:	6 times
Download:	0 times

Concrete & Brickwork Accessories

Documents