HIGH CAPACITY SOLUTIONFOR CRUSHING HARD AND ABRASIVE MATERIALS
MCH-1150CONE CRUSHERS
capacıtyUp to 250 Tons/hour
Motor Power200 kW
Weight18400 kg
For crushing hard and abrasive materials in agregate and mining industries; cone crushers are most pref-ered and used as primary, secondary and tertiary crushers. Beside crushing gravel and granite, cone crushers are used in mining industry for crushing ores such as iron, copper, magnesite and chromium. MEKA cone crushers, with their robust design and high qual-ity production characteristics, are suitable for even very hard and abrasive materials.Also, MEKA cone crushers provides low operation and maintenance costs. MCH 1150, new member of MEKA cone crusher series, is a high performance equipment which com-bines advantages of cone crushers and MEKA quality.
www.mekaglobal.com
MCH 1150 MAIN CHARACTERISTICS- Special alloy cast steel bottom and top shells,- Alloy steel main shaft,- Alloy bronze bearings,- High quality items chosen from suppliers.
Nominal Capacity in mt/h at C.S.S. (mm)
MCH 1150
CrusherModel
MaxMotor Size (kW)
Max. Feed Size (mm)
215
175
14085
MCH-1150CONE CRUSHERS
www.mekaglobal.com
MEKA MCH 1150 Cone Crusher Capacity
CLOSED SIDE SETTING (CSS)ADJUSTMENT SYSTEMClosed side setting is made on control panel. In case of overload, setting is increased automatically until overload disappears. Under normal load, setting is adjusted to set val-ue automatically.In case of an uncrushable material, such as a piece of iron, enters in crushing chamber, Closed Side Setting System re-acts and increases opening by lowering the mainshaft to get the uncrushable material out of chrushing chamber.
The selection of settings in the shaded areas assumes special consideration of the feed size distribution, closed circuit and the crushing characteristics of the material.
Consult MEKA if any of the following conditions is current:
• A high content of fines in the feed.• Closed circuit operation (if it results in much fines in the feed).• Hard material.• Clay in the feed.These are common conditions which will increase the minimum possible C.S.S.
MCH-1150CONE CRUSHERS
www.mekaglobal.com
MEKA MCH 1150 Cone Crusher Curves
0
10
20
30
40
50
60
70
80
90
100
0,01 0,10 1,00 10,00
% P
AS
SIN
G T
HR
OU
GH
SQUARE SCREEN HOLE (MM)
MCH 1150 MEDIUM FINE CRUSHING CHAMBER
12mm
14mm
16mm
19 mm
22 mm
Polinom. (12mm)
Polinom. (14mm)
Polinom. (16mm)
Polinom. (19 mm)
Polinom. (22 mm)
0
10
20
30
40
50
60
70
80
90
100
0,01 0,1 1 10 100
% P
AS
SIN
G T
HR
OU
GH
SQUARE SCREEN HOLE (MM)
MCH 1150 MEDIUM COARSE CRUSHING CHAMBER
19 mm
22 mm
25 mm
32 mm
38 mm
Polinom. (19 mm)
Polinom. (22 mm)
Polinom. (25 mm)
Polinom. (32 mm)
Polinom. (38 mm)
0
10
20
30
40
50
60
70
80
90
100
0,01 0,1 1 10 100
% P
AS
SIN
G T
HR
OU
GH
SQUARE SCREEN HOLE (MM)
MCH 1150 COARSE CRUSHING CHAMBER
17 mm
20 mm
25 mm
30 mm
36 mm
Polinom. (17 mm)
Polinom. (20 mm )
Polinom. (25 mm)
Polinom. (30 mm)
Polinom. (36 mm)
0
10
20
30
40
50
60
70
80
90
100
0,1 1 10 100
% P
AS
SIN
G T
HR
OU
GH
SQUARE SCREEN HOLE (MM)
MCH 1150 EXTRA COARSE CRUSHING CHAMBER
26 mm
29 mm
34 mm
44 mm
Polinom. (26 mm)
Polinom. (29 mm )
Polinom. (34 mm)
Polinom. (44 mm)
ABOUTMEKA GLOBAL
ESTABLISHED IN 1987We have over 32 years of experience and the passion of the first day.
MANUFACTURING CAPACITY400 Crushing Screening Equipment / year 300 Concrete Batching Plant / year
focused on manufacturing of
CONCRETE PLANTS and CRUSHING&SCREENING EQUIPMENT
Expert EngineeringExperienced R&D engineers within Meka work to design machines that are the most suitable for your needs.
EXPORT COUNTRIESMore Than 90 Countries...USA, Russia, Chile, England, Poland, France, Romania, Bulgaria, Serbia, Kosovo, Bahrain, Qatar, UAE, Belgium, Algeria, Sudan, Morocco, Bangladesh, Cameroon, Libya, Burkina Faso, Nigeria, Ethiopia, Kazakhstan, Ukraine, Georgia, France, Tajikistan, Azerbaijan, Austria, etc.
STRONG REFERENCESWe have produced more than 3,000 plants and have gained incalculable experience.Heidelberg, Hochtief, Vinci Contractors, Lafarge, Gazprom, Italcementi Group, London Concretes/Aggregates, Holcim, Strabag Gmbh, Euro Cement Group, Breedon Aggregates, Knauf, Enka, Galfar, Alesco, Recon International, Richard Costain, Tekfen, Lakeshore Group, Gama, Orascom, CCC etc.
HIGH CAPACITY SOLUTIONFOR CRUSHING HARD AND ABRASIVE MATERIALS
MCH- 900CONE CRUSHERS
capacıtyUp to 180 Tons/hour
Motor Power110 kW
Weight9200 kg
For crushing hard and abrasive materials in agregate and mining industries; cone crushers are most pref-ered and used as primary, secondary and tertiary crushers. Beside crushing gravel and granite, cone crushers are used in mining industry for crushing ores such as iron, copper, magnesite and chromium. MEKA cone crushers, with their robust design and high qual-ity production characteristics, are suitable for even very hard and abrasive materials.Also, MEKA cone crushers provides low operation and maintenance costs. MCH 900, new member of MEKA cone crusher series, is a high performance equipment which com-bines advantages of cone crushers and MEKA quality.
www.mekaglobal.com
MCH 900 MAIN CHARACTERISTICS- Special alloy cast steel bottom and top shells,- Alloy steel main shaft,- Alloy bronze bearings,- High quality items chosen from suppliers.
MCH- 900CONE CRUSHERS
www.mekaglobal.com
MEKA MCH 900 Cone Crusher Capacity
CLOSED SIDE SETTING (CSS)ADJUSTMENT SYSTEMClosed side setting is made on control panel. In case of overload, setting is increased automatically until overload disappears. Under normal load, setting is adjusted to set value automatically.In case of an uncrushable material, such as a piece of iron, enters in crushing chamber, Closed Side Setting System reacts and increases opening by low-ering the mainshaft to get the uncrushable material out of chrushing chamber.
The selection of settings in the shaded areas assumes special consideration of the feed size distribution, closed circuit andthe crushing characteristics of the material.
C.S.S. SH 6 8 10 13 16 19 22 25 29 32 3575 16 85 90 95 100 105 11090 19 100 110 115 120 125 13090 22 135 140 145 150
110 25 155 160 165110 29 180 18575 16 80 85 85 90 95 10090 19 95 100 105 110 115 12090 22 125 130 135 140
110 25 140 145 150110 29 180 16555 16 60 70 75 80 85 9075 19 70 80 90 100 10575 22 90 100 110 12590 25 100 106 115 135
110 29 110 115 125110 32 135
C.S.S. (mm)Crusher
Max. Feed Size Eccentric Pinion
Appr.Motor Power
Ecc. Throw
MCH 900-MC
60-70 85 355/1160
MCH 900-EC
80-100 130 355/1160
MCH 900-C
70-80 110 335/1160
Consult MEKA if any of the following conditions is current:
• A high content of fines in the feed.
• Closed circuit operation (if it results in much fines in
the feed).
• Hard material.
• Clay in the feed.
These are common conditions which will increase the minimum possible C.S.S.
MCH- 900CONE CRUSHERS
www.mekaglobal.com
MEKA MCH 900 Cone Crusher Curves
0
10
20
30
40
50
60
70
80
90
100
0,01 0,10 1,00 10,00
% P
ASSI
NG
THRO
UGH
SQUARE SCREEN HOLE (MM)
MCH 900 MEDIUM COARSE CRUSHING CHAMBER
CSS (13 mm)
CSS (15 mm)
CSS (19 mm)
CSS (22 mm)
CSS (25 mm)
0
10
20
30
40
50
60
70
80
90
100
0,01 0,1 1 10 100
% P
ASSI
NG
THRO
UGH
SQUARE SCREEN HOLE (MM)
MCH 900-C COARSE CRUSHING CHAMBER
CSS (17 mm)
CSS (20 mm)
CSS (25 mm)
CSS (30 mm)
0
10
20
30
40
50
60
70
80
90
100
0,1 1 10 100
% P
ASSI
NG
THRO
UGH
SQUARE SCREEN HOLE (MM)
MCH 900-EXTRA COARSE CRUSHING CHAMBER
CSS (20 mm)
CSS (26mm )
CSS (29 mm)
CSS (34 mm)
ABOUTMEKA GLOBAL
ESTABLISHED IN 1987We have over 32 years of experience and the passion of the first day.
MANUFACTURING CAPACITY400 Crushing Screening Equipment / year 300 Concrete Batching Plant / year
focused on manufacturing of
CONCRETE PLANTS and CRUSHING&SCREENING EQUIPMENT
Expert EngineeringExperienced R&D engineers within Meka work to design machines that are the most suitable for your needs.
EXPORT COUNTRIESMore Than 90 Countries...USA, Russia, Chile, England, Poland, France, Romania, Bulgaria, Serbia, Kosovo, Bahrain, Qatar, UAE, Belgium, Algeria, Sudan, Morocco, Bangladesh, Cameroon, Libya, Burkina Faso, Nigeria, Ethiopia, Kazakhstan, Ukraine, Georgia, France, Tajikistan, Azerbaijan, Austria, etc.
STRONG REFERENCESWe have produced more than 3,000 plants and have gained incalculable experience.Heidelberg, Hochtief, Vinci Contractors, Lafarge, Gazprom, Italcementi Group, London Concretes/Aggregates, Holcim, Strabag Gmbh, Euro Cement Group, Breedon Aggregates, Knauf, Enka, Galfar, Alesco, Recon International, Richard Costain, Tekfen, Lakeshore Group, Gama, Orascom, CCC etc.