DECLARATION OF PERFORMANCE CONF-DOP_HB-VMZ 11/20-E
HALFEN HB-VMZ INJEKTION SYSTEM No. H40-07/0256
1 © 2020
1. Unique identification code of the
product-type HALFEN HB-VMZ INJECTION SYSTEM
2.
Type, batch or serial number or any other element
allowing identification of the construction product as
required pursuant to Article 11(4)
HALFEN HB-VMZ INJECTION SYSTEM see ETA-07/0256
Annex A; Batch number: see packaging of the product
3.
Intended use or uses of the construction product, in accordance with the applicable harmonized
technical specification, as foreseen by the manufacturer:
Generic type and use torque-controlled bonded anchor
For use in cracked and uncracked concrete C20/25 - C50/60 (EN 206)
Base material / base material strength
Zinc-plated steel:
dry internal conditions only
covered sizes: VMZ: M8, M10, M12, M16, M20, M24
VMZ-IG: M6, M8, M10, M12, M16, M20
Hot-dip galvanised steel:
dry internal conditions only
covered sizes: VMZ: M8, M10, M12, M16, M20, M24
VMZ-IG: M6, M8, M10, M12, M16, M20
Stainless steel (marking A4):
internal and external use without particular aggressive
conditions
covered sizes: VMZ: M8, M10, M12, M16, M20, M24
VMZ-IG: M6, M8, M10, M12, M16, M20
Highly corrosion resistant steel (marking HCR):
internal and external use with particular aggressive
conditions
covered sizes: VMZ: M8, M10, M12, M16, M20, M24
VMZ-IG: M6, M8, M10, M12, M16, M20
Temperature range (if applicable) Temperature Range I: -40°C to +80°C
Temperature Range II: -40°C to +120°C
4.
Name, registered trade name or registered trade mark
and contact address of the manufacturer as required
pursuant to Article 11(5)
HALFEN GmbH (part of Leviat), Liebigstraße 14, 40764
Langenfeld, Germany
5.
Where applicable, name and contact address of the
authorized representative whose mandate covers the
tasks specified in Article 12(2)
-
6.
System or systems of assessment and verification of
constancy of performance of the construction product as
set out in Annex V
System 1
7. In case of the declaration of performance concerning a
construction product covered by a harmonised standard -
8.
In case of the declaration of performance concerning a
construction product for which a European Technical
Assessment has been issued
Deutsches Institut für Bautechnik, Berlin issued ETA-07/0256
on the basis of ETAG 001.
The notified body NB 2873 performed under system 1:
(i) initial inspection of the manufacturing plant and of factory
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 2
production control;
(ii) continuous surveillance, assessment and evaluation of
factory production control.
9.
Declared performance
Essential Characteristics Design Method Performance Harmonized
Technical
Specification HB-VMZ-A HB-VMZ-IG
Characteristic resistance ETAG 001, Annex C
EN 1992 – 4:2018 ETA-Annex C1-C5 ETA-Annex C10-C12
ETAG 001
Characteristic resistance
for seismic Categorie C1
and C2
EOTA TR 045 ETA-Annex C6, C7 -
Displacements under
tension and shear loads
ETAG 001, Annex C
EN 1992 – 4:2018 ETA-Annex C8, C9 ETA-Annex C12
Where pursuant to Article 37 or 38 in the Specific
Technical Documentation has been used, the
requirements with which the product complies
-
10. The performance of the product identified in points 1 and 2 is in conformity with the declared performance in point 9.
This declaration of performance is issued under the sole responsibility of the manufacturer identified in point 4.
Langenfeld, 10.11.2020
Signed for and on behalf of the manufacturer by
Richard Wachter ppa. Dr.-Ing. Dirk Albartus (Managing Director) (Manager Engineering)
H-9
15-1
1/2
0-E
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 3
Annex C1:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 4
Annex C2:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 5
Annex C3:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 6
Annex C4:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 7
Annex C5:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 8
Annex C6:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 9
Annex C7:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 10
Annex C8:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 11
Annex C9:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 12
Annex C10:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 13
Annex C11:
HALFEN HB-VMZ INJEKTION SYSTEM CONF-DOP_HB-VMZ 11/20-E
© 2020 14
Annex C12: