Date post: | 11-Jan-2016 |
Category: |
Documents |
Upload: | easter-summers |
View: | 222 times |
Download: | 5 times |
Confidential 1
KX-TDA200/100 SystemKX-TDA200/100 System (Ver.2.0)
Chapter 6.0
Enhanced Items
Panasonic Communications Co., Ltd.Panasonic Communications Co., Ltd.
Network Business CompanyNetwork Business Company
Edition 1.3 07 Oct., 2004Edition 1.3 07 Oct., 2004
2Confidential
• General
GeneralSystem Highlights
New Feature & Condition
System Capacity Expansion
Software Compatibility
New Hardware
System Connection Diagram
3Confidential
System Highlights
V1.0
V1.1
Networking(QSIG), Call Center, VoIP Gateway,CTI (CSTA/TAPI), T76xx Line Up, Wireless System
- Digital XDP & Double Extension Capacity by MEC - 1 Slot VoIP Gateway 4ch Card (Panasonic proprietary)- New CS to DPT Port
V2.0 - IP-GW16- IP-PT Extension- Network DSS- Sending Caller ID to SLT port- External Sensor & Relay- Hotel Feature Enhancement (7 items)- LCD for VM Operation
4ConfidentialTD
A0920New Feature & Condition - 1
16 ports IP-GW(CO) card
IP PT Extension
NDSS (Network Direct Station Selection)
Caller ID to SLT (Analogue Extension)
External Sensor
External Relay
Wake up Call Set with Voice Guidance (KX-TVA/TVM)
Voice Message Delete when Check Out(KX-TVA/TVM)
Check in / Check out Control
Telephone Charge Print Out when Check out
Remote Wake up Call Set
SMDR for External Hotel Application
SMDR(Programmable) for External Hotel Application
LCD for VM Operation (KX-TVA/TVM)
VM Message Number Display on LCD(KX-TVA/TVM)
CTI Enhancement
PC Phone / PC Console Improvement - DDI Name
PC Phone / PC Console Improvement - Copy from Outlook (International Code)
Behavior of ICD-G Key & ICM key with CTI including PC Phone / PC Console
Highlight
Hotel
Voice Mail
CTI
O
O
IP-EXT16 Card, PT(KX-NT136)
EXT-CID Card, SLT8
EIO4, OPB3
EIO4, OPB3
KX-TVM
KX-TVM
6line_PT
MEC
KX-T76xx w/ LCD, KX-TVM
6line_PT, KX-TVM
Another conditionFeatures
5Confidential
TDA09
20
New Feature & Condition - 2
Making Calls
Receiving Calls
Hold / FWD / TR
Others
TRS by Dial Time out
Speed Dial Name Reference for Public Call through Private Network
Incoming Call Log for Public Call through Private Network
CLIP when Transfer
System Speed Dial Memory Expansion
Personal(Station) Speed Dial Memory Expansion
Analogue CO line monitor
20 Pause for 2nd Dial Code
Walking Extension for Virtual Extension (For "Hot Disking" Use)
Dummy Extension of PBX for CO Telephone Number
SMDR 24H Format
SMDR Caller ID Modification
Outgoing message (OGM) recording duration expansion
MEC
MEC
Features Another condition
6Confidential
System Capacity ExpansionWithout MEC (TDA0105), no change on system capacity made.
1.Number of Ports
(Ver.1.1)
3. System Speed Dial
(Ver.2.0)
4. Station Speed Dial
(Ver.2.0)
Without MEC (TDA0105) With MEC (TDA0105)
TDA100
TDA200
80 (108)
160 (216)
32digits, 1000 entries/System
32 digits, 10 entries/EXT
TDA100
TDA200
TDA100
TDA200
144 (158)
288 (316)
32digits, 1000 ent./System
+ 1000 ent./Tenant x 8
32 digits, 100 entries/EXT
* The number of extension is consisted with all type of extension including IP-PT.
2.Number of Extension
(Ver.1.1)
TDA100
TDA200
64
128
128
256
With MEC (TDA0105), following item’s capacities are expanded.
80 ports 108 ports 144 ports 158 ports
Slot1 16 Ext. Same as left Slot1 16 Ext. + 16DXDP Same as leftDLC16 DLC16Slot2 16 Ext. Same as left Slot2 16 Ext. + 16DXDP Same as leftDLC16 DLC16Slot3 16 Ext. Same as left Slot3 16 Ext. + 16DXDP Same as leftDLC16 DLC16Slot4 16 CO 30 ch Slot4 16 Ext. + 16DXDP Same as leftLCOT16 DLC16E1Slot5 16 CO 30 ch Slot5 16 CO 30 chLCOT16 LCOT16E1 E1
MEC
Configuration of “1.Number of Ports” for TDA100
7Confidential
Software CompatibilityMPR / LPRMPR / LPR
MPR 2.0xxMPR 2.0xxMPR 1.0xx & 1.1xxMPR 1.0xx & 1.1xx
YesYes
Yes w/o TVMYes w/o TVM
YesYes
YesYes
DLC/DHLC 2.008DLC/DHLC 2.008
DLC/DHLC 2.005DLC/DHLC 2.005
MPR / PC maintenance consoleMPR / PC maintenance console
MPR 2.0xxMPR 2.0xxMPR 1.0xx & 1.1xxMPR 1.0xx & 1.1xx
NoNoYesYes1.071.07
InstallationInstallation
YesYesNoNo2.02.0
YesYesYesYes1.07 + 2.01.07 + 2.0
SLC 2.002SLC 2.002
SLC 1.002SLC 1.002
YesYes
YesYes
YesYes
Yes w/o EXT-CIDYes w/o EXT-CID
OPB3 1.006OPB3 1.006
OPB3 1.002OPB3 1.002
YesYes
YesYes
YesYes
Yes w/o EIO4 (Relay/Sensor)Yes w/o EIO4 (Relay/Sensor)
IPGW4E firmware 1.2IPGW4E firmware 1.2
IPGW4E firmware 1.0, 1.1IPGW4E firmware 1.0, 1.1
YesYes
YesYes
YesYes
Yes w/o NDSSYes w/o NDSS
8Confidential
New Hardware – Option Card
EIO4(External Input/Output)
KX-TDA0164
4-port external input/output card.To be mounted on the OPB3 card (TDA0190).
TDA200 4TDA100 2
IP-EXT16(16ch VoIP Extension)
KX-TDA0470
TDA200 8TDA100 4
16-channel VoIP extension card.Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods.
EXT-CID(Extension Caller ID)
KX-TDA0168
Sends Caller ID signals to extension ports.To be mounted on the SLC8 card (TDA0173).
TDA200 8TDA100 4
IP-GW16(16ch VoIP Gateway)
KX-TDA0490
TDA200 4TDA100 2
16-channel VoIP gateway card.Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and G.711 CODEC methods.
Upgrade SD(Upgrade to enhanced V2.0)
KX-TDA0920
TDA200 1TDA100 1
Optional SD Memory Card to upgrade the Hybrid IP-PBX with software version 1 or 1.1 to version 2.0,And it adds NDSS feature and CTI enhancement, too.
9Confidential
Navigation Key
Dual color 24 Flexible Keys
Visible Large Ring/Msg Lamp
6 Lines 24 digits LCD /w backlit
RJ45RJ45 RJ45RJ45
RJ11RJ11
New Hardware – Peripheral - 1KX-NT136 (IP-PT)Connection via IP
User Interface is same as T7636.
Almost of KX-T7636 Functions is in it.
PC-Phone/Console doesn’t work with.
PC Maintenance Console doesn’t connect.
TDATDA
LANLAN
PCPC
BenefitRemote Office, Easy moving in network, Cost saving
10Confidential
New Hardware – Peripheral - 2TVM Series (New Voice Processing System)
All function of TVP series and New features listed below.
TVM50
TVM200
- VM operation with LCD (T7636, T7633 or T7630 is required.)
- Message notification by LCD message (6 lines LCD is required.)
- Wake-up call set with voice guidance for Hotel application
- Voice message delete when check-out for Hotel application (6 lines LCD is required.)
TVM200 TVM50
Connection to PBX
Max. channel
Max. mailbox
Recording media
Recording time
Programming I/F
TVP200 TVP50
DPT/SLT port DPT/APT/SLT port
6ports(12ch) 2ports (2ch)
1024 32 mailboxes
HDD Flash
32h 6h
Hyper Terminal
RS232C, Modem
Hyper Terminal
RS232C
VM-Link, DPT/SLT DPT/APT/SLT port
12ports (24ch) 6ports (6ch)
1024 64
HDD Flash
128h 8h
PC Soft
USB, LAN, Modem
PC Soft
USB, LAN, Modem
11Confidential
System Connection Diagram - 1
Trunk (Telephone Company Lines)
Analogue / BRI / PRI / T1 / E1
Trunk (Telephone Company Lines)
Analogue / BRI / PRI / T1 / E1
Remote PC
PC PC
SLT DPT APT DSS DPT DSS
SLT
FAX
Wireless
Phone
ISDN
Telephone
CS
PSVoice Processing
System
PC
Router
Server PC
Private
IP Network
Private
IP Network
T7633/36 PC
USB
T7600 DPT T7600 DPT
DXDP
Pager/
Speaker
Amplifier
PC or Printer
Batteries
PCIP-PT
External Sensor/ External Relay Device
Doorphone & Door Opener
BGM/MOH
Peripheral Connection Legacy Connection
IP Connection
12Confidential
System Connection Diagram – 2DLC16 (TDA0172)
DLC8 (TDA0171)
DHLC8 (TDA0170)
MSLC16 (TDA0175)
SLC16 (TDA0174)
SLC8 (TDA0173)
CSIF4 (TDA0143)
CSIF8 (TDA0144)
CTI-LINK (TDA0410)
OPB3 (TDA0190)
DPH4 (TDA0161)
DPH2 (TDA0162)
ECHO16 (TDA0166)
MSG4 (TDA0191)
LCOT4 (TDA0183)
LCOT16 (TDA0181)
LCOT8 (TDA0180)CID/PAY8 (TDA0189)
CID8 (TDA0193)
DID8 (TDA0182)
E&M8 (TDA0184)
BRI4 (TDA0284)
BRI8 (TDA0288)
PRI30 (TDA0290CE/CJ)
PRI23 (TDA0290)
T1 (TDA0187)
E1 (TDA0188)
IP-GW4 (TDA0480)
IP-GW4E (TDA0484)
MPR
MEC (TDA0105) RMT (TDA0196)
PSU-S/M/L
TDA0108/0104/0103
T7633/36PC
T7600 DPTT7600 DPT
DPT DSS PT-IF CS
PSVoiceProcessingSystem
SLT
FAX
APT
WirelessPhone
SLT
Same capability of DLC
FAXWirelessPhone
SLT
CSLAN
PC Server PCDoorphone & Door Opener
Server PC Pager/Speaker
Amplifier
Radio
PS
Router
Batteries
SMDR
PC
PS
TN
Analogue
E&M
ISDN BRI
ISDN PRI
T1
E1
PrivateIP Network
IP-GW16 (TDA0490) EIO4 (TDA0164)
IP-EXT16 (TDA0470)
EXT-CID (TDA0168)
LAN
External Sensor / External Relay Device
IP-PT PC
13Confidential
•Function – Highlight
Function - Highlight
14Confidential
16 ports IP-GW Card - 1- model number is KX-TDA0490.- 16ch IPGW Card occupies a Single slot in TDA100/200
Physical I/F single Ethernet 10/100BaseT (auto sense) LED’s - Status, Link, Data, Online, Alarm & Busy
- G729a/G723.1/G711- T.38 (FAX) mode is not supported (FAX = G711)- Configuration using Web browser (English)
- 100% call compatibility with TDA0484/3480- Interoperability with TDA0480
Incoming call, Outgoing call and CLIP only.- Interoperability with another manufacturers :
Not guaranteed.- Power factor is 0.
15Confidential
16 ports IP-GW Card - 2
The compatibility of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below:
Compatibility TDA0480 TDA0484/TDA3480 TDA0490
Signalling H.323 V2 H.323 V2 H.323 V2
QSIG service Proprietary H.323 V4 Annex M1 H.323 V4 Annex M1
Max networked IPGW’s 511 511 511
Voice Codec G.723/G.729a G.711/G.723.1/G.729a G.711/G.723.1/G.729a
FAX Protocol T.38 G.711 G.711
Echo canceller 16ms 16ms 48/128ms
AGC Yes No No
DTMF Tone Detection Yes Yes Yes
SNMP Yes No No
Event Notice by email Yes No No
DHCP No Yes (Client) Yes (Client)
NAT No No No
Compatibility
16Confidential
16 ports IP-GW Card - 3
FunctionTDA0480
connected toTDA0480
TDA0384/TDA0484/TDA0490
Connected to
TDA0384/TDA0484/TDA0490
TDA0384/TDA0484/TDA0490
Connected to
TDA0480CLIP OK OK OK
COLP OK OK No
COLR OK OK No
CNIP OK OK No
CNIR OK OK No
CONP OK OK No
CONR OK OK No
CT(Avoid Tromboneing) OK OK No
CF(Avoid Tromboneing) OK OK No
CCBS OK OK No
Making/Receiving Call OK OK OK
Fax Connection OK OK No
The interoperability of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below:
Interoperability
17Confidential
Two type wirings require two types of construction, maintenance and their time.
IP PT Extension (Benefit 1)
Router
LAN
Router
LAN
IP-PT
What is benefit of IP Extension
Unified wiring give low cost construction and maintenance.
One type wiring save them.
18Confidential
IP PT Extension (Benefit 2)
LAN
EXT.201 EXT.201EXT.201 EXT.201?
Slot:201 Port:01
Slot:301 Port:02
MOVEJust MOVE
What is benefit of IP Extension
Setting change is not necessary Easy & Quick move enable
Setting change will be required.
IP-PT IP-PT
Normal Extension
IP Extension
19Confidential
IP PT Extension (Benefit 3)
LeasedLine
PBX PBX
Branch Office
Head Office
What is benefit of IP Extension
PBX is not necessary for Branch Office. All setting can be controlled by Head Office.
Router Router
IP NetworkPrivate
IP-PT IP-PT
PBX
LANLAN
Head Office
Branch Office
20Confidential
IP PT –1 (Sample Configuration)
Sample of configurationSample of configuration-Feature of IP PT(KX-NT136) is basically same as KX-T7636.Feature of IP PT(KX-NT136) is basically same as KX-T7636.
LAN
Head Office Branch Office
Primary Ethernet Port
IP-EXT16
IP-PT
IP-PT
IP-PT
(DHCP Server)
Secondary Ethernet Port
PC
IP NetworkPrivate
Except: OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking ExtensionExcept: OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension
21Confidential
IP PT –2 (Requirements)
-DHCP (Dynamic Host Configuration Protocol) Server is not supported by IP-EXT16 card.
Note: Following features are not supported.Note: Following features are not supported.-OHCA, USB connection, 12CO Key connection, Digital OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking ExtensionXDP, and Walking Extension
- Cable: 100 BASE-TX Category 5 or higher
- Power source: Power-over-Ethernet (PoE)or KX-A237 AC Adaptor is necessary
Requirements
- IP-EXT16 card is required.
You need to assign IP address of IP-EXT16 card by manual.
IP-PT cannot be used for initial set-up of PBX system.
22Confidential
IP PT –3 (Programming IP-EXT. Card)Programming Instruction
Assign IP Address for IP-EXT. card by manual
Assign IP Address for IP-PT Register IP-PT
IP Address & Subnet mask (GW Address for IP-PT)
1. Configuration 1. Slot
IP-EXT16 Property2. System 14. IP Extension Setting
* If necessary (See page IP-PT7)
Step 1 Step 2 Step 3
23Confidential
2. Press “Set-up” soft key from 2nd time
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT Register IP-PT
Programming Instruction
IP PT –4 (Programming IP-PT)
At start up
1. Power on IP-PT 3. Select “Network”
Step 1 Step 2 Step 3
IPL Start… Now Loading
Searching…
Setup
Menu
Please first setup !OK [ENTER]
MenuNetworkPBXVLANMaintenance
STORE EXIT CONT ENTER
LCD status 2. At 1st installation
2. From 2nd time
1. Start up
2. Press “Enter” key at 1st installationor
3. Menu select
24Confidential
IP PT –5 (Programming IP-PT)
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT Register IP-PT
Programming Instruction
With DHCP Server
4. DHCP: Enable 5. Select “PBX” 6. Assign IP Address for IP-EXT16 card
7. Store
(Automatic Assignment: IP Address for Subnet mask, IP-PT Default GW)
Step 1 Step 2 Step 3
DHCP Enable
IP Address 0. 0. 0. 0
Subnet Mask 0. 0. 0. 0
NEXT
Disable
EXIT ENTER
MenuNetworkPBXVLANMaintenance
STORE EXIT CONT ENTER
PBX IP Address ?
192.168. 0.100
EXIT CLER ENTER
LCD status4. 5. 6.
25Confidential
IP PT –6 (Programming IP-PT)
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT Register IP-PT
Programming Instruction
Without DHCP Server
4. DHCP: Disable 5. Select “IP-Address” 6. Assign IP Address for IP-PT
7. Select “Subnet mask” 8. Assign IP Address for Subnet mask
* 9. Select “Default GW”
11. Select “PBX” 12. Assign IP Address for IP-EXT16 card
*10. Assign IP Address for Default GW 13. Store
Step 1 Step 2 Step 3
DHCP Enable
IP Address192.168.0.101
Subnet Mask255.255.255. 0
NEXT
Disable
EXIT ENTER
MenuNetworkPBXVLANMaintenance
STORE EXIT CONT ENTER
PBX IP Address ?
192.168. 0.100
EXIT CLER ENTER
LCD status 4. – 8.11. 12.
26Confidential
IP PT –7 (Programming IP-PT)
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT Register IP-PT
Programming Instruction
Without DHCP Server
Step 1 Step 2 Step 3
LAN
Head Office Branch Office
IP-EXT16
IP-PT
IP-PT
PC
IP NetworkPrivate
DHCP Enable
Default Gateway192.168. 0. 1
PREV
Disable
EXIT ENTER
Gateway: 192.169.0.1 Gateway:10.75.0.1
Router Router
27Confidential
IP PT –8 (Register IP-PT to PBX)
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT Register IP-PT
Programming Instruction
1. Configuration 15. IP-Extension Port
Select: ON
Registration:Start
Confirm: OK
LCD of IP-PT is changed to normal
Registration
Step 1 Step 2 Step 3
30 SEP. 11:09AM FRI
PROG INFO RING MENU
UNREGISTERED TO SERVER
OK[ENTER]
28Confidential
IP PT –9 Virtual LAN
Necessary
Information
Local Office Remote Office
IP-PT EXT.101 IP-PT EXT.102 IP-PT EXT.103 IP-PT EXT.104
IP-PT IP Address 192.168.0.101 192.168.0.102 10.75.0.103 10.75.0.104
Subnet Mask Address
255.255.255.0 255.255.255.0
Default Gateway Address
192.168.0.1 10.75.0.1
Card IP Address 192.168.0.100 10.75.0.100
VLAN ID 1VLAN ID is necessary for IP-PT and VLAN(L2 Switch)
VLAN Name : SalesID : 1Port on VLAN: 1-4Tagged VLAN: Null
VLAN Name : SalesID : 1Port on VLAN: 1-4Tagged VLAN: Null
PHY. Port 1 2 3 4 5 6 VLAN No. 1 1 1 1 2 2
VLAN(L2 Switch)
29Confidential
IP PT –10 Virtual LAN
MenuNetworkPBXVLANMaintenance
STORE EXIT CONT ENTER
VLAN Enable
Primary port
Secondary port (TO PC)
Disable
EXIT ENTER
Primary port
VLAN ID
VLAN Priority
1
7
PHY. Port 1 2 3 4 5 6 VLAN No. 1 1 1 1 2 2
L2 Switch
LANIP-EXT16
IP-PT IP-PT
Gateway: 192.169.0.1 Gateway:10.75.0.1
VLAN Name : SalesID : 1Port on VLAN: 1-4Tagged VLAN: Null
VLAN Name : SalesID : 1Port on VLAN: 1-4Tagged VLAN: Null
VLAN ID = 1
VLAN ID = 1
VLAN ID = 1
VLAN ID = 1
LCD status
IP NetworkPrivate
Router
VLAN ID = 1 VLAN ID = 1
L2 switch configuration
Head Office Branch Office
30Confidential
QSIG, VoIP
303
302
304
NetworkMonitorPBX
MonitoredPBX
NDSS (Network Direct Station Selection)- NDSS is a DSS key referring to an extension of other PBX
- It works with both of the open numbering and the closed numbering.
- It’s used for monitoring extension status and making or transferring calls.
- Only one TDA can be a Monitor PBX
- Maximum 32 extensions in the network can be monitored.
- Any extension of Monitor TDA can have NDSS.(Network Operator)
- Both of Monitor PBX and Monitored PBX require KX-TDA0920
Network Operator
BenefitCentralized Operator
Idle
Busy
KX-TDA0920Mandatory
KX-TDA0920Mandatory
304 To call to extensionPush =
TDA0920is required.
IdleOff =302
Busy, DND (trunk)Red On =303
31Confidential
NDSS – 2TDA0920
is required.
QSIG, VoIPNetwork
ID=0
ID=0
ID=0
ID=0
ID=0
ID=0
ID=0
Monitored Ext
ID=2
Monitored Ext
ID=3
Monitored Ext
ID=4
ID=1
Network Operator
ID: 2-8 Monitored PBX
Each ID must be unique in the network.
V2.0 or later
ID: 0 (default) Normal PBX
It’s neither a monitor PBX nor a Monitored PBX.
Some PBXs transmit status information of Monitored Ext.
V2.0 or later
ID: 1 Monitor PBX
Only one in the network.
V2.0 or later
ID: none Other PBX
Before V2.0, TDA30, TD500
Each TDA100/200 V2.0 has Network PBX ID.ID=1
ID=2-8
ID=0 (default)
Monitor PBX
Monitored PBX
Normal PBX
Network PBX ID
1PRG* Refer
32Confidential
NDSS – 3TDA0920
is required.
Status Information Routing
Monitored Ext
ID=3
102
ID=1
Network Operators Monitored Ext
ID=2
ID=0
ID=0
ID=0
ID=0
ONOFFONOFFONOFFON
ON
OFF
101
OFF103
ISDN Q-SIG ISDN Q-SIG ISDN Q-SIG
ISD
N Q
-SIG
ISD
N Q
-SIG
IP NetworkVoIP Q-SIG
302
402
Idle Busy
Idle Busy
302 Busy
302 Busy
402 Busy
402 Busy
Transmitting route for Status Information data
must be constructed.
NDSS data TransferVoIP ISDN : Enable
2PRG* Refer
Case : ISDN (PRI, BRI) Q-SIG
Network Data TransferYes (ON) : Send
No (OFF) : Receive* Q-SIG port base setting
ON OFF
5PRG* Refer
ID=3
IPG
W a
t s
lot1
IPG
W a
t s
lot3
IPG
W a
t s
lot6
Network Operator = 102IPGW Card Slot to send out = slot3
Status Info. IP Routing Table
402 Busy
Case : VoIP Q-SIG
3PRG* Refer
33Confidential
NDSS – 4Network Monitor Extensions Table
Monitored Ext
ID=3
102
ID=1
Network Operators
Monitored Ext
ID=2101
302
402
QSIG, VoIPNetwork
Starting monitoring & Stopping monitoring
No.
001
002
003
032
Ext. Name for reference
302
Network PBX ID
2
3402
Monitor Extensions Table
* Only for a monitor PBX
Ma
x.
32
Ex
t.
* 7 48C.Tone
#Network Ext. No.
NDSSor
NDSSTo start monitoring
To stop monitoring
All NDSS start monitoring.
* Any extension can do.
* Only a manager extension can do.
4PRG* Refer
TDA0920is required.
34Confidential
NDSS – 5
Conditions-TDA0920 must be in both of monitor PBX and monitored PBX.
- The firmware (not LPR) of IP-GW4E(TDA0484) must be Version1.2 or later.
- Network PBX ID:1-8 must be unique in the network.
- It’s possible to stop monitoring at monitored PBX by PC Maintenance Console.
- NDSS does not work on PC-Phone / PC-Console.
- You can not back up all of NDSS configuration into DSYS.( * You need to check and re-configure some part of NDSS after initialize reset, even you have DSYS as backup. )
(1) Connect a browser to IP-GW4E. ( Updating is done through a browser. It’s not from PC Maintenance Console.)
(2) Login to IP-GW4E with the name: Installer, PW: Installer.
(3) Change the status of the card from “RUN” to “STOP”.
(4) Now, you can upload a firmware and update the card with the procedure in the manual (3.3 Data Management).
Updating Firmware of IP-GW4E
TDA0920is required.
35Confidential
NDSS – 6Programming Instruction - 1
Network PBX ID Assignment1PRG
2PRG
3PRG
4PRG
On
ly w
he
n I
D =
2 -
8
On
ly w
he
n I
D =
1
NDSS data transfer VoIP ISDN
ISDN VoIP
Status Info. Routing Table
Network Monitor Extensions Table
How many time NDSS data can be transferred
Up
to
32
Frequency of NDSS data from IPGW or PRI card
Any extension number which is reachable from this monitor PBX
A slot number of IPGW card which the data is sent from
* The PBX(ID=0) can’t perform this direction.
TDA0920is required.
36Confidential
NDSS – 7Programming Instruction - 2
Case : ISDN (PRI, BRI) Q-SIG
Network Data TransferYes (ON) : Send
No (OFF) : Receive* Q-SIG port base setting
ON OFF
5PRG
Data transmitting direction over Q-SIG
TDA0920is required.
37Confidential
Caller ID : 12345678
Caller ID to SLT - 1Caller ID from SLC port to Normal Telephone, Cordless Telephone, FAX machine,etc.
FSK (ETSI and Bellcore) signaling only
16 digits maximum
Adding Trunk Access Number for calling back Purpose (Programmable)
TDA0173 (SLC8) and TDA0168 (EXT-CID) are required.
PSTN12345678(0, 9) +
Only FSKFSK, DTMF, others
Max. 16 digitsFor Calling back (Programmable)
BenefitRecognizing caller, easy calling back
302
SLC8
EXT-CID
(0,9) 12345678
302302
38Confidential
Receiving a call
Answer and transfer
On Hook
302
Caller ID to SLT - 2Action in Unscreened transfer operation
TR
CID:12345678
302
12345678
12345678
- CID is between 1st bell and 2nd bell
- Incoming Call Log Information is not shown on the SLT.
- TDA0168(EXT-CID) must be installed on TDA0173(SLC8).
- LPR software of TDA0173 (SLC8) must be 2.002 or later.
- One EXT-CID supports 8 ports. (All ports of SLC8 which has EXT-CID on it can send out CID.)
- EXT-CID can be installed onto all off SLC8s in a TDA system.
Condition
SLT stops ringing
and rings again
39Confidential
Caller ID to SLT – 3Programming items - 1
Adding Trunk Access Number: Enable/Disable
Adjusting interval: 0-15
Enable sending CID to Ext.: Enable/Disable
40Confidential
Caller ID to SLT - 4Programming items - 2
CID Modification table
SLC8
Property
Check if EXT-CID is installed
- modified CID will be sent to SLT port
41Confidential
Caller ID to SLT – 5
Priority of items displayed when TDA is receiving FSK CID
FSK CID may bring information such as private, out of area or long distance.
If TDA received
“private” or “out of area”
“long distance”
Another items
“private” or “out of area” is displayed.
“long distance” is displayed.
Caller ID and Name is displayed.
Result
prio
rity
high
low
42Confidential
External Sensor - 1
If a device connected to the external sensor becomes active, there are 3 outcomes:
(1)Sensor call will be generated to the pre-programmed extension
(2)Generates SMDR Printout
(3)Generates 3rd Party CTI command
The sensor call destination can be a PT, SLT,PS, or ISDN extension but not an ICD-Group.
- If a sensor call arrives at an extension
Display : pre-assigned name of sensor port [5.5]
Ring : Distinctive ringer pattern can be assigned (triple, or special double ring, so on) [2.8.3]
- Special Tone(Dial Tone 3) will be sent to answering extension.
- If nobody answer sensor call, sensor call stops with pre-programmed time [2.4.3].
43Confidential
External Sensor - 2
Input Signal Decision Time = This is the time delay before Extension begins to Ring.
Input Signal Detection Reopening Time = This is the time it takes the sensor to reset hence the time it will take to respond to the
next input.
The External Sensor has some timing parameters that can be set using the maintenance console [1.] and clicking on the OPB3 card.
Timings
44Confidential
External Sensor - 3
Power to the external sensor is provided from the EI04 card and must be grounded through the EI04 card as indicated in the diagram below. A pair of “sensor” and “common” lines are connected to the EI04 card for each external sensor. The TDA detects inputs from the sensor when the signal is under 100 Ohms.
Connection Diagram
45Confidential
External RelayExtensions can activate external relay for controlling external devices(On/Off) by feature code. There is a COS that has to be programmed to enable this feature.
It is possible to activate the relay for pre-programmed time [5.4].
The relay is the relay normally open.
And has a maximum switching voltage of : 24VDC(1A)
30VAC(1A)
46Confidential
•Function – Hotel
Function - Hotel
47Confidential
Hotel - 1
- Wake up Call Set with Voice Guidance (KX-TVA/TVM)
- Voice Message Delete at Check Out, Automatically(KX-TVA/TVM)
6 Line LCD PT for Hotel Operator
“Wake up call is set at 07:30.”
KX-TVA200 or TVM200
KX-TDA200 or TDA100
KX-T7636
- Check in / Check out Control
- Telephone Charge Print Out when Check out
- Remote Wake up Call Set
- SMDR for External Hotel Application
- Programmable SMDRfor External Hotel Application
48Confidential
Hotel - 2
Check out
Automatic telephone charge print out
Remote Wake up Call set
Automatic voice message delete
Check in button
*Check out button
Operation Assignment
Hotel Operator EXT.
*Check in / Check out
*Timed reminder Start / Answer / No response
*Programmed message
Check out + Room No. (EXT. No.) + Print / YES
Check in + Room No. (EXT. No.)
*Select print item
Dial *76*1 + Room No. + Time
Check in
*Telephone / Minibar / Others
*Charge: Margin/Tax
*TAX rate: telephone /minibar/others
*Telephone margin
*Header / Footer
49Confidential
Hotel - 3 (Check In)
- Check in / Check out Control6 Line LCD PT for Hotel Operator
Check-in: On hook status Check-in button Dial EXT.No. or DSSEnter Enter
Check-out: On hook status Check-out button Enter Dial EXT.No. or DSS Enter
50Confidential
Hotel - 4 (Wake up Call / Check Out)
-Remote Wake up Call SetDial * 7 6 *
1: Set
0: CancelorOff hook status EXT. No. or DSS
Hour: Minute (+ 0: AM 1:PM by 12H)0: Once
1: Dairyor
- Telephone Charge Print Out when Check out
Check-out: On hook status Check-out button Enter Dial EXT.No. or DSS Enter
PRINT NEXT YES (Soft Key)Enter “Minibar” and “Others”
Room:103
Telephone: 00000.00Minibar : 00000.00Others : 00000.00
EXIT NEXT PRINT
Room:103
Confirm check out ?
NO YES
Enter Room Number
EXIT ENTER
LCD status
51Confidential
Hotel - 5 (SMDR Setting)
-Programmable SMDR
for External Hotel Application
- SMDR for External Hotel Application
Check in/out
Timed Reminder Start/Answer/No Response
Printing Message (on SMDR) can be assigned.
Dial *761 Printing Message No. #
52Confidential
Hotel - 6 (Billing Sheet)
Sample of Call Billing Sheet
53Confidential
Hotel - 7 (Rate Calculation)
Margin/Tax Rate Assignment
[Calculation Method]
[Charge received from telephone company]
[1 - Tax Rate] x [1 - Margin Rate]
Advice of Charge: ISDN
[Meter indication received from telephone company] x [Call Charge Rate]
[1 - Tax Rate] x [1 - Margin Rate]
Pay tone: Analog trunk + pay tone cardMeter Pulse: E1 line
54Confidential
•Function – Voice Mail
Function – Voice Mail
55Confidential
LCD for VM Operation - 1 (Receive a Message)
SHIFT EXIT ERASE STOP
ROBINE SCHNEIDERMBX 120AUG24 03:47PMNEW 00:03:12
****------
Main Menu
Deliver Msg.
A.A. StatusCheck Distribution
EXIT
Receive Msg.
3 messages
MBX 203 AUG24 11:04AM!3275307 AUG24 09:23AM
EXIT ERASE PLAY
ROBINE2 AUG24 03:47PM!
The screen shots show how easy it is to Receive a Voice mail message with the new KX-TVM series.
Condition-PT must be T76xx with LCD.
- Max.5 Language’s
56Confidential
LCD for VM Operation - 2 (A.A Status)
Main Menu
Deliver Msg.Check Distribution
EXIT
Receive Msg.
A.A. Status
A.A. Status
Covering Extn.Mbx. Retention Mode
EXIT
Call Transfer
Incomplete Handling
EXIT DALL
Call Transfer Status
Enable ScreeningDisable Int. PagingDisable Beeper
Disable Blocking
The screen shots show how easy it is to change the automated attendant settings with the new KX-TVM series.
57Confidential
Voice Mail Message Number display on LCD
26 JUL. 10:20AM MON
PROG INFO RING MENU
Incoming Call :001Voice Message :002
The number of new messages can be indicated on the LCD of PT.
This feature is supported on TVM series voice mail.
Condition- PT with 6 line LCD
58Confidential
•Function – CTI
Function - CTI
59Confidential
CTI Enhancement
Supporting New Hardware External Sensor, IP-PT
Controlling Ring Pattern for redirected call
Setting Extension Absent Message
Another enhancement
MIC
MWL
FCO key
SP On/Off
SP Volume
Ring On/Off
LCD Display contents
PT
YES
YES
YES
YES
YES
YES
YES
IP-PT
YES
YES
YES
YES
YES
YES
YES
PS
YES
YES
YES
YES
Controlling PT
MultiPBX Loading Function 2 PBXs are controlled by TAPI.
New Functions
TDA0920is required.
Condition- KX-TDA0920 is mandatory.
- TSP Built 2.0.0.27 or later
- USB ports or LAN interface on PC
- Windows 2000(Pro, Server) or Windows XP(Pro)
* This does not mean
that PMS controls two PBXs.
60Confidential
PC Phone / PC Console Improvement
DDI(DID) name of PBX can be displayed.
DDI(DID) name of PC has priority.
For example, "+81-92-477-1234"
will be 0081924771234 or 81923771234 or 924771234 by programming.
New Features
Improvements
the operator can not answer the call from Incoming Group screen.the operator can answer the call from Incoming Group screen.
BeforeNew
New Feature Enhancement for “External Sensor”New Feature Enhancement for display the DDI Name from PBX when alerting
Import function from Outlook Phone Book(the method for International code)
Screen sentences were revised to correct sentences (except English)
When “Call Pickup by DSS ICD Group Call” is disabled by programming,
when it saved without inputting to TextMemo,
Under using Italian language,
Incoming/Outgoing record (Call Log) is not left in Call Log.Incoming/Outgoing record (Call Log) is left in Call Log.
BeforeNew
the operator cannot attach a photo into “Pop-up” except BMP.the operator can attach a photo into “Pop-up” with other than BMP format, too.
Before
New
61Confidential
•Function - Making Calls
Function – Making Calls
62Confidential
Keep (default)Disconnect Activate this feature!
TRS by Dial Timeout- TRS by Dial Time out
0: Call PTT Operator in North America
RESTRICT
00: Credit Call NO RESTRICTION
Example 1: Operation in U.S.A.
(Inter-digit timer is working in checking TRS.)
Keep Disconnect
FWD to 9CO-CO callNo DTMF-R in trunk cards
DTMF dialing can go thru. (No check)
FWD to 9CO-CO callNo DTMF-R in trunk cards
DTMF dialing can go thru. (No check)
But TDA disconnects by the timer.
PS
TN
PS
TNdials
dials
Restriction table99restrict
Example 2: Preventing escaping from TRS
63Confidential
•Function - Receiving Calls
Function – Receiving Calls
64Confidential
Speed Dial Name Reference through Network
1234567
Private Network
Panasonic1234567
6. Feature 1. Speed Dialing & Caller ID
1. Main Table
9+1234567Panasonic
If Caller ID is matched to the number in System/Personal Speed Dial, the correspond name can be displayed on LCD. It is effective through Network, too.
Telecom Line
65Confidential
Incoming Call Log for Public Call through Private Network
TDA distinguishes incoming calls from the private network between private call and public call.
PublicNetwork
PrivateNetwork
PBX code952Ext.101
CID:03-1234-5678
CID:06-4444-5555
CID:03-1234-5678
CID:952-101
CID:06-4444-5555
Private Call
Public Call
Public Call
Threshold Value= 9
Threshold value: 0-15 (default:9)
Incoming CallLogging
Call Type Info.
From other PBX
Digits Comparison
With threshold
Public
Private
Private
Don’t Care
Over
Under or equal
Result
Public
Public
Private
TDA V2.0 can send correct call type.TDA V1.0, V1.1 send “Private Call” as call type.
*
Priority condition
10 digits > 9
6 digits =< 9
66Confidential
•Function – Hold/Forward/Transfer
Function – Hold/Forward/Transfer
67Confidential
CLIP when Transfer
CLIP to be sent to CO when transferring (to CO) has following choices.
* This configuration does not apply for Call Forwarding.
CLIP in forwarding is received CID.
Disable (default): send CID of EXTEnable : send CID of Held CO Party
- send CID which is sent in usual of the extension’s making a call
- send CID of held CO party
68Confidential
•Function – Others
Function - Others
69Confidential
Others - 1
System Speed Dial
Station Speed Dial
(Personal Speed Dial)
32digits,
1000 entries/System
32 digits,
10 entries/EXT (01-09)
TDA100
TDA200
TDA100
TDA200
32digits,
1000 ent./System + 1000 ent./Tenant x 8
32 digits,
100 entries/EXT (00-99)
MEC
MEC
Each Tenant has a choice.- to use a list for system
- to use a list for tenant
Original 10 entries aren’t copied to first 10 entries in 100 entries.
- Memory Expansion
70Confidential
Others - 2
- Analog CO Line Monitor Detection of physical line disconnection
- 20 Pauses for 2nd Dial Code
V1.1 = Max. 4 Pauses, V2.0 = Max. 20 Pauses
If CO line is disconnected physically, the CO port become Out of Service Automatically.
Except AL/NE model LCOT card by difference of hardware
71Confidential
Others - 3
- Working Extension for Virtual ExtensionV1.0= SLC16 without phone
V1.1= DLC16 temporary use only
- Dummy Extension of PBX for CO Tel. No.
You can use mobile phone like as extension.
TDA100/200: Max 128 PS or Mobile phone
TDA30: Max 28 PS or Mobile phone
PBX recognize CO Tel. No. as EXT. No.
72Confidential
Others - 4
Time stump in 24h format
Caller ID Modification
Example 1:
Default for US/Canada is "Before Modification". Default for other is "After Modification".
For example, call from 0312345678 through ISDN CO will be print as
312345678 by "Before Modification" mode.
0312345678 by "After Modification" mode.
Example 2:
441633653666(Call from UK)
or 44163365366(Call in US) by "Before Modification" mode
010441633653666(Call from UK)
or 144163365366(Call in US) by "After Modification" mode
- SMDR Enhancement
- After Modification- Before Modification Default of US, Canada
Default of others
- 12H- 24H Default of NE
Default of others
73Confidential
Others - 5
- Outgoing message (OGM) recording duration expansion
V1.1 or before V2.0
Total 8 minutes
Up to 64 messages
Total 8 minutes
Up to 64 messages
Max. One minutefor each message
Max. Eight minutesfor each message
74Confidential
•To Start TDA100/200 V2.0
To Start TDA100/200 V2.0
75Confidential
PC Maintenance Console Compatibility
Automatically
V1.1 is connected.
V1.0 is connected.
Initial Screen
V2.0 is connected.
V1.07V2.0
Automatically
Two versions are installed
into a PC.
76Confidential
PC Maintenance Console Installation - 1
PCC provides two installers.
The Installation order is important.
pcprogv2000R5.exe
pcprogv107cR3.exe
(V2.0)
(V1.07)
Only for TDA V2.0
For TDA V1.1 & V1.0
Result
Possible programming
TDAV1.0 V1.1
TDAV2.0TDA
NoNo Yes
YesYes No
OK !YesYes Yes
No good !YesYes No
You need UNINSTALL V1.07 and V2.0 and install again in correct order.
* You can uninstall both of V1.07 and V2.0 at once in normal uninstall operation.
NoneV1.07
V2.0 None
V1.07 V2.0+
V2.0 V1.07+
1st
install2nd
install
Installation without uninstalling 1st install.
Case1:
Case2:
Case3:
Case4:
77Confidential
PC Maintenance Console Installation – 2
Area Selection Difference
V1.07 V2.0
“Please enter your country code …” “Please select suffix code.”
78Confidential
3. Conversion Complete.
DSYS of V2.0 is saved at local PC
Data Conversion
2. Update DSYS to V2.0 by PC Maintenance Console V2.0
2-1 Open DSYS (V1.1 or V1.0) from PC Maintenance Console V2.0.
2-2 Following dialog appears.
No conversion, opening DSYS as it is.
Going back to initial screen.
Caution : Converting from V1.0 requires PC Maintenance Console V1.07, too.
1-1 “Tool” => “SD Memory Backup”
1-2 “Utility” => “File Transfer PBX (SD Card) to PC”
1. Back up DSYS (V1.0 or V1.1) to PC
79Confidential
Upgrade PBX1. Prepare following files
- PMPR 2.0, DLNG0 2.0, DLNG1 2.0- DSYS 2.0 --- Converted DSYS or New DSYS created by PC Maintenance Console
2. Download above files to PBX
3. Reset PBX by command- V1.0054 or later --- Please select PMPR_SUB, DSYS_SUB, then reset- Before V1.0054 --- Please reset without any care.
Select
Select
4.Connect PC-Soft again and download other files as the dialog box saying.
5.If PC-Soft require reset, reset PBX again, then you can finish upgrading.
80Confidential
KX-TDA0920+ =
Normal SD DKEY-SDFile:
Enhancement by Upgrade SD card - 11. Some features are enabled by Upgrade SD card (KX-TDA0920) .
+ =
- TDA V1.0- TDA V1.1- TDA V2.0 (Normal)
TDA V2.0Enhanced
KX-TDA0920
Upgrade SD
What is an
upgrade SD ?
2. Enhancement procedure
The information in DKEY-SD is different for each SD card.
5-1 “Utility” => “File Transfer PC to PBX (SD Card)”, DSYS will be saved as DSYS_SUB.5-2 Restart from command with following choices. DSYS: Use Replace File
PMPR: Keep Present FileTDA V2.0 Enhanced begins to work.
Backup current DSYS to PCStep2
Convert DSYS to V2.0Step3
Send User’s DSYS to TDAStep5
Make backup of TDA0920 into local PCStep1
Step4 Change SD to TDA0920,then execute initialize reset
YesYesYes
Yes Yes Yes
Yes
Yes Yes
Yes Yes
From V1.0 or V1.1 V2.0 (working) V2.0 (brand new)
81Confidential
Enhancement by Upgrade SD card - 23. Data Reset After Upgrade
- Incoming Call Log
- Outgoing Call Log (including Last Number Redial)
- Message Waiting
- SMDR
- Advice of Charge (AOC) / Pay Tone
- ICD Group monitor log for supervisor
- PT handset/headset volume
- PT SP-PHONE volume
- PT ring volume
- PT display contrast
- Live Call Screening (LCS) On/Off
- Hands-free Answerback status
- Absent Message status of extensions
(Absent Message data itself is no cleared.)
- Fwd/DND status (FWD destinations are not cleared.)
- PBX date and time
- Timed Reminder
- LPR Timed Update time
- Daily test start time
- Extension Lock/Remote Extension Lock
- Extension PIN Lock/Extension PIN Lock counter
- Verified Code PIN Lock/Verified Code PIN Lock counter
- Password Lock counter for Remote System Programming
- PBX Error Log
- ICD Group login status
(All extensions are set to Login by default.)
- ICD Group Ready/Not Ready status
(All extensions are set to Ready by default.)
Log
System
PT/Ext
Status
Group
Status
Others
And
PS registration information will be cleared, too.
82Confidential
Enhancement by Upgrade SD card - 34. How to go back to normal TDA
Prepare SD card of previous version. (Normal V2.0, V1.1 or V1.0)
Step2 Execute initialize reset of TDA
Step4 Execute normal reset of TDA (It’s no need to send DSYS to TDA.)
Step1 Set the slide switch position to “Lock”, then insert to TDA.
* TDA must be turned off, at first.
Step3 Set the slide switch position to “Un-Lock”, then insert to TDA.
* TDA must be turned off, at first.
TDA begins working with previous version.
83Confidential
Thank you very much !Thank you very much !
• Thank you very much !