Date post: | 07-Aug-2018 |
Category: |
Documents |
Upload: | jose-alaniz |
View: | 234 times |
Download: | 2 times |
of 5
8/21/2019 Configuring Devicenet Network
1/10
CONFIGURING DEVICENET NETWORK
Previous requirements for configuring device net network:
Hook up Allen Bradley Cable to the PC COM port and to the Device net
Interface !"D# port$
Device net Interface !"D# %hould be plugged into Device &et 'canner
'(C# through the ) pin green connector$
Device net Interface %hould be powered up$ Check the po%ition of the %witch
located on one %ide of the Interface %et up on the upper po%ition#$
"ollow the%e %tep% in order to get the device net network running:
'(C *u%t be in PROG Mode$
'tart +%(in,$ -he +%(in, *ain widow will open$
8/21/2019 Configuring Devicenet Network
2/10
"ro* the Communications *enu. %elect Coni!ure Drivers a% %hown
above$ -he following window will appear thi% %creen %hoot *ay change
fro* your% depending on the driver% you had configured before in +%(in,#$
"to# a$$ the drivers %howed up on the Configured Drivers by %electing the*
and pre%%ing on 'top$
"ro* Available Driver Types pull down li%t %elect DeviceNet Drivers$
8/21/2019 Configuring Devicenet Network
3/10
Click on Add New $ /ou will %ee the following choice%$
'elect the %$$en &rad$e' ())*+KFD,-he Driver Configuration window will
appear$ "e$ect t-e COM Port nu*ber your PC i% u%ing for co**unicating
and click OK$
8/21/2019 Configuring Devicenet Network
4/10
-he %oftware will take a few %econd% to configure the driver$ 0hen it i% done
the following pro*pt will appear$
'elect the default nu*ber na*e ())*+KFD+( and click on OK$
Clo%e +%(in,$
You will use the driver you just configured to browse and configure the device
net network with RsNetWor for DeviceNet!
"ro* the CD I %ent you open +%&et0or, "ile 1$dnt .ms+/**0s$c0micro0(+
/+1+2+EMPT3+4+((+50modu$ar,dnt6
"ro* Net7or8 *enu %elect On 9ine and pre%% %cce#t$
8/21/2019 Configuring Devicenet Network
5/10
+%&et0or, will %tart brow%ing the network$
8/21/2019 Configuring Devicenet Network
6/10
Once you are connected in On$ine: fro* Net7or8 *enu %elect Do7n$oad
to Net7or8,
Pre%% OK and downloading will %tart$
8/21/2019 Configuring Devicenet Network
7/10
Once downloading i% done and 'ou do not !et an' icon on any device net
network device% 'canner. D&I *odule and I2O *odule%# you can !o o$ine
and place the "9C in RUN Mode$
Once downloading i% done and 'ou !et an icon on t-e "canner device. go
%ee help or 3'y*bol (egend4$ Could be po%%ible that the "canner Node
does not matc- with the node addre%% been %etup on the la%t downloading$
-herefore. fro* Too$s *enu %elect Node Commissionin!,
Pre%% &ro7se on the window %howed up below$
8/21/2019 Configuring Devicenet Network
8/10
"ro* the new window %elect ())*+KFD+( Device&et Driver -hi% window
*ay be different to your% depending on the driver% you had configured
before on the +%(in,#
8/21/2019 Configuring Devicenet Network
9/10
0hen %electing 56678!"D85 Driver all device% connected on the network are
di%played on the right %ide of the window$ 'elect ()1)+"canner Modu$e and
pre%% OK$
On the new window appeared pre%% &ro7se$ After a few %econd% the field
for entering the new &ode Addre%% i% enabled$ -ype in the new &ode
Addre%% -he 'canner Module i% alway% %etup a% &ode Addre%% 7 or 5.
therefore type in 5 %ince the 1dnt file wa% configured a% 7 and that could be
the rea%on why they *i%*atch# and pre%% %##$'$
8/21/2019 Configuring Devicenet Network
10/10
Download again the &etwork Configuration and 'ave Change%$
Di%connect fro* On(ine
Place the '(C in +9& Mode$
Veri' 7-et-er ater #$acin! "9C in Run Mode 'ou !et or not an' a$arm
code on t-e "canner Dis#$a' or an' o t-e 9eds .Modu$e and Net6 on t-e
"canner is $as-in! red or !reen,
C-ec8 t-e meanin! o t-e %$arm Code on t-e Trou;$es-ootin! .C-a#ter )
o t-e DeviceNet"canner,#d i$e6 on t-e CD,