For wood construction
Construction
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
23
ContentSPAX product characteristics 4–5
Partial thread with flat countersunk or washer head
Outer diameter Ø 8 and 10 mm 6–9
Partial thread with flat countersunk head
Outer diameter Ø 12 mm 10–13
Full thread with flat countersunk head
Outer diameter Ø 8, 10 and 12 mm 14–17
Example applications 36–37 Instructions for Ü-Logo and CE marking 38–39
Technical information 18–19
Partial thread with washer head Outer diameter Ø 6 mm 20
Full thread with cylindric head
Outer diameter Ø 6 mm 21
Full thread with cylindric head
Outer diameter Ø 8 mm 22
Partial thread with flat countersunk or washer head
Outer diameter Ø 8 mm 24–25
Outer diameter Ø 6, 8, 10 and 12 mm 26–31
SPAX threaded rod
Full thread without head or with hex head
Outer diameter Ø 16 mm 32–35
Zinc yellow passivated head shape page
WIROX head shape page
Blue zinc plated head shape page
Stainless steel head shape page
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
45
Washer head
Better tightening of connections also of warped boards.
Easy bolting of steel parts and sheet metal to wood without prior counter boring of the bore hole.
Guarantees higher beam supporting forces and allows savings with regard to piece numbers and working time.
MULTI Head
Product characteristics
Flat countersunk head T-STAR with milled ribs
Washer head
Cylindric head
MULTI Head
Flush countersinking. Mills in wood and stops on metal.
Flat countersunk head T-STAR with milled ribs
Flush countersinking. Countersinks the screw head flush into the wood.
Cylindric head
Low splitting effect when sinking the head.
Can be easily countersunk in wood.
T-STAR plus
4CUT
Starting at screw lengths of 160 mm, the special moulding at the thread runout of partial thread screws significantly reduces the screwing-in torque.
CUT point and SPAX typical ground serrations
4CUT and ground serrations
Ground serrations
For quick and secure fastening.
4CUT
No pre-drilling (wood-dependent), its point effectively reduces the splitting effect. The square end pushes aside the fibre of the wood and reduces the screwing-in torque.
CUT point
Precision placement allows screwing in without pre-drilling (wood-dependent). Effectively reduces splitting of the wood.
4CUT
T-STAR plus
Positive and secure fit of the BIT and better driving, e. g. when working overhead.
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
SPAX typical ground serrations
For quick and secure fastening.
67
The SPAX penetrates the wood significantly more easily and faster!
8 mm x 600 mm
into fir wood gluelam
Conventional screw
Scre
win
g to
rque
[Nm
]
Time [s]
80–450 mm total length
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Features: Significantly reduced screwing torque and reduced splitting effect
Easier and faster screwing
No pre-drilling necessary (wood-dependent)
Approved by German and European building authorities under licensing number Z-9.1-449, Z-9.1-511 and ETA-12/0114 – approved by building authorities for fastening rooftop insulation systems
T-STAR plus T40
Length specification and manufacturer ID on the head
Washer head ensures higher pull through forces
Partial thread with flat countersunk or washer headOuter diameter 8 and 10 mm
1.22
2.43
3.65
4.86
6.08 7.3
8.51
9.73
10.9
12.2
13.4
14.6
15.8 17
18.2
19.5
20.7
21.9
23.1
24.3
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
89
Flat countersunk head, T-STAR plusMULTI Head and 4CUT, case hardened, slide-coated
Zinc yellow passivated A2L
Dimensions [mm] Packaging unit SPAX No.
Thread Ød1
Lengthtotal
Ls
Lengthpartial thread LgT
BIT size
T
SPAXBOX
[pieces]
8.0 80 47 40 50 0191020800805
Ø dk = 15.1 mm
100 57 40 50 0191020801005120 70 40 50 0191020801205140 80 40 50 0191020801405160 80 40 50 0191020801605180 80 40 50 0191020801805200 80 40 50 0191020802005220 80 40 50 0191020802205240 80 40 50 0191020802405260 80 40 50 0191020802605280 80 40 50 0191020802805300 80 40 50 0191020803005320 80 40 50 0191020803205340 80 40 50 0191020803405360 80 40 50 0191020803605380 80 40 50 0191020803805400 80 40 50 0191020804005450 80 40 50 0191020804505
10.0 80 50 50 50 0191021000805
Ø dk = 18.6 mm
100 60 50 50 0191021001005120 80 50 50 0191021001205140 80 50 50 0191021001405160 80 50 50 0191021001605180 80 50 50 0191021001805200 80 50 50 0191021002005220 80 50 50 0191021002205240 80 50 50 0191021002405260 80 50 50 0191021002605280 80 50 50 0191021002805300 80 50 50 0191021003005320 80 50 50 0191021003205340 80 50 50 0191021003405360 80 50 50 0191021003605380 80 50 50 0191021003805400 80 50 50 0191021004005450 80 50 50 0191021004505
90°
Ls
LgT
Ø d1
Ø d k
50
'!0A35DA-aebieg!T40
0191
0208
0240
5
A2L
8X240 Z-9.1-449
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
4CU
T®
Other lengths, head shapes and surfaces on request. NEW!
T-STAR plus T50
T-STAR plus
MULTI Head
4CUT
4CUT and ground serrations
50
'!0A35DA-ajheeh!T40
0251
0208
0240
5
A2L
8X240 Z-9.1-449
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
4CU
T®
Dimensions [mm] Packaging unit SPAX No.
Thread Ød1
Lengthtotal
Ls
Lengththread Lg
BIT size
T
SPAXBOX
[pieces]
8.0 80 70 ■ 40 50 0251020800805
Ø dk = 20 mm
100 80 ■ 40 50 0251020801005120 80 ■ 40 50 0251020801205140 80 ❑ 40 50 0251020801405160 80 ❑ 40 50 0251020801605180 80 ❑ 40 50 0251020801805200 80 ❑ 40 50 0251020802005220 80 ❑ 40 50 0251020802205240 80 ❑ 40 50 0251020802405260 80 ❑ 40 50 0251020802605280 80 ❑ 40 50 0251020802805300 80 ❑ 40 50 0251020803005320 80 ❑ 40 50 0251020803205340 80 ❑ 40 50 0251020803405360 80 ❑ 40 50 0251020803605380 80 ❑ 40 50 0251020803805400 80 ❑ 40 50 0251020804005450 80 ❑ 40 25 0251020804505
10.0 80 70 ■ 50 50 0251021000805
Ø dk = 25 mm
100 80 ■ 50 50 0251021001005120 80 ■ 50 50 0251021001205140 80 ❑ 50 50 0251021001405160 80 ❑ 50 25 0251021001605180 80 ❑ 50 25 0251021001805200 80 ❑ 50 25 0251021002005220 80 ❑ 50 25 0251021002205240 80 ❑ 50 25 0251021002405260 80 ❑ 50 25 0251021002605280 80 ❑ 50 25 0251021002805300 80 ❑ 50 25 0251021003005320 80 ❑ 50 25 0251021003205340 80 ❑ 50 25 0251021003405360 80 ❑ 50 25 0251021003605380 80 ❑ 50 25 0251021003805400 80 ❑ 50 25 0251021004005450 80 ❑ 50 25 0251021004505
Washer head, T-STAR plus4CUT, case hardened, slide-coated
Zinc yellow passivated A2L
Ls
Lg
Ø d1
Ø d k
Other lengths, head shapes and surfaces on request. NEW!
T-STAR plus T50
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
T-STAR plus
Washer head
4CUT
4CUT and ground serrations■T-STAR plus, full thread
❑T-STAR plus, partial thread
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
1011
100 – 600 mm total length
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Features: No pre-drilling necessary (wood-dependent)
Absorption of high tensile and compressive forces by being fully threaded
Approved by German and European building authorities under licensing number Z-9.1-449, Z-9.1-511 and ETA-12/0114 – approved by building authorities for fastening rooftop insulation systems
T-STAR plus
Length specification and manufacturer ID on the head
Partial thread with flat countersunk headOuter diameter 12 mm
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
1213
Flat countersunk head T-STAR plus with milled ribs
SPAX typical ground serrations
Dimensions [mm] Packaging unit SPAX No.
Thread Ød1
Lengthtotal
Ls
Lengthpartial thread LgT
BIT size
T
SPAXBOX
[pieces]
12.0 100 60 50 25 0191021201005
Ø dk = 22.6 mm
120 80 50 25 0191021201205140 80 50 25 0191021201405160 100 50 25 0191021201605180 100 50 25 0191021201805200 100 50 25 0191021202005220 100 50 25 0191021202205240 100 50 25 0191021202405260 100 50 25 0191021202605280 100 50 25 0191021202805300 100 50 25 0191021203005350 100 50 25 0191021203505400 100 50 25 0191021204005450 100 50 25 0191021204505500 100 50 25 0191021205005550 100 50 20 0191021205505600 100 50 20 0191021206005
Flat countersunk head, T-STAR plusMilled ribs, case hardened, slide-coated
Zinc yellow passivated A2L
Ls
Ø d190°
LgT
Ø d k
Other lengths, head shapes and surfaces on request. NEW!
T-STAR plus T50
500000918140910 pieces in a counter display
1 x T 502 x T 40
SPAX-No.Packing unit
2 x T 20
SPAX BITcheck for wood construction T-STAR plus
2 x T 30
Screwing aid
NEW!incl. T50
SPAX BITcheck for wood construction T-STAR plus: 6 SPAX-BITs T-STAR plus length 25 mm, 1 SPAX-BIT T-STAR plus T50 length 35 mm, packing unit 10 BITcheck in a counter display
For use with SPAX 8 mm allowing precise and pinpoint fastening in the rafter (67° angle).
Practical screwing aid for rooftop insulation
50011208000111 unit per box
New
SPAX-No.
SPAX-No.Packing unit
1415
Bürgerhaus Altdorf © Volker Winkler
Features: Absorption of high tensile and compressive
forces by being fully threaded
Absorption of particularly high pulling forces compared to partial thread screws
Wide spectrum of applications through screw lengths of up to 600 mm
Building authorities approval under Z-9.1-519 and ETA-12/0114 as wood connector
Length specification and manufacturer ID on the head
Full thread with flat countersunk headOuter diameter 8, 10 and 12 mm
160 – 600 mm total length
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
Lengthfull thread LgV
BIT size
T
SPAXBOX
[pieces]
8.0 160 40 50 1201020801605
Ø dk = 15.1 mm
180 40 50 1201020801805200 40 50 1201020802005220 40 50 1201020802205240 40 50 1201020802405260 40 50 1201020802605280 40 50 1201020802805300 40 50 1201020803005350 40 50 1201020803505400 40 50 1201020804005450 40 50 1201020804505500 40 25 1201020805005550 40 25 1201020805505600 40 25 1201020806005
Thre
ad c
lose
to h
ead
Other lengths, head shapes and surfaces on request.
Flat countersunk head, T-STAR plusMULTI Head and CUT point, case hardened, slide-coated
CUT point and SPAX typical ground serrations
MULTI Head
1617
Zinc yellow passivated A2L
T-STAR plus
Ø d190°
Ls
LgV
Ø d k
50
'!0A35DA-bddegg!T40
1201
0208
0240
5
A2L
8X240 Z-9.1-519
CU
T
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
Other lengths, head shapes and surfaces on request.
Flat countersunk head, T-STAR plusMilled ribs and CUT point, case hardened, slide-coated
CUT point and SPAX typical ground serrations
Zinc yellow passivated A2L
Flat countersunk head T-STAR plus with milled ribs
Ø d190°
Ls
LgV
Ø d k
10X240
Senkkopf mit Fräsrippen T 50verzinkt, gelb pass.
Art
.: 12
0102
1002
405
50 S
tück
'!0A35DA-bddhab!
A2L
Z-9.1-519
CU
T
0672-CPD-I 14.12.17
ETA-12/011413DoP 1
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
Lengthfull thread LgV
BIT size
T
SPAXBOX
[pieces]
10.0 200 50 50 1201021002005
Ø dk = 18.6 mm
220 50 50 1201021002205240 50 50 1201021002405260 50 50 1201021002605280 50 50 1201021002805300 50 50 1201021003005350 50 50 1201021003505400 50 50 1201021004005450 50 50 1201021004505500 50 25 1201021005005550 50 25 1201021005505600 50 25 1201021006005800 50 25 1201021008005
12.0 200 50 25 1201021202005
Ø dk = 18.6 mm
220 50 25 1201021202205240 50 25 1201021202405260 50 25 1201021202605280 50 25 1201021202805300 50 25 1201021203005350 50 25 1201021203505400 50 25 1201021204005450 50 25 1201021204505500 50 25 1201021205005550 50 20 1201021205505600 50 20 1201021206005
Thre
ad c
lose
to h
ead
Thre
ad c
lose
to h
ead
NEW!
T-STAR plus T50
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Product range
expanded
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
1819
– the new coating
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Features: WIROX provides excellent anti-corrosion protection
Revision of the relevant national and European standards for the building trade means that future requirements in respect of anti-corrosion protection of fittings and fasteners are likely to be tightened.
Using WIROX gives you 10 times greater anti-corrosion protection compared with yellow zinc plating of identical coat thickness.
WIROX offers benefits for application in Usage Class 2 as per DIN 1052, especially in the case of open structures such as carports or pergolas.
WIROX in comparison with stainless steel
Despite the high corrosion resistance of WIROX, it can’t substitute stainless steel.
WIROX – environment-friendly
WIROX is free of Chrome (VI) making it significantly more environment-friendly – both in manufacture and use – than conventional anti-corrosive coatings.
WIROX abrasion resistant
WIROX possesses a distinctly higher level of surface hardness than, for example, conventional yellow zinc plating or zinc lamina coatings. Giving greater resistance to damage of the surface coating, leading to a reduction in corrosion.
Further information on page 23.
T-STAR plus
Washer head
Washer head, T-STAR plus4CUT, case hardened, slide-coated
P3J
Other lengths, head shapes and surfaces on request.
2021
Ls
Lg
Ø d1
Ø d k
6.0 60 56 ■ 30 200 0251750600605
Ø dk = 13.6 mm
80 61 ■ 30 100 0251750600805100 61 ❑ 30 100 0251750601005120 68 ❑ 30 100 0251750601205140 68 ❑ 30 100 0251750601405160 65 ❑ 30 100 0251750601605180 65 ❑ 30 100 0251750601805
4CUT and ground serrations
4CUT
'!0A35DA-bhiajc!T30
0251
7506
0180
5
P3J
6X180 Z-9.1-235
corrosion protection
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
4CU
T® 100
■T-STAR plus, full thread
❑T-STAR plus, partial thread
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
BIT size
T
SPAXBOX
[pieces]
Lengththread Lg
6.0 80 30 200 1211750600805
Ø dk = 8.4 mm
100 30 100 1211750601005120 30 100 1211750601205140 30 100 1211750601405160 30 100 1211750601605180 30 100 1211750601805200 30 100 1211750602005
Thre
ad c
lose
to h
ead
Cylindric head, T-STAR plus4CUT, case hardened, slide-coated
T-STAR plus
4CUT and ground serrations
Cylindric head
P3J
Other lengths, head shapes and surfaces on request.
Ls
LgV
Ø d1
Ø d k
1211
7506
0180
5
T30
P3J
100
'!0A35DA-bhibga!6X180 Z-9.1-519
corrosion protection
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
4CU
T®
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
BIT size
T
SPAXBOX
[pieces]
Lengthfull thread LgV
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
2223
T-STAR plus
CUT point and SPAX typical ground serrations
Cylindric head
8.0 200 40 50 1221750802005
Ø dk = 10 mm
220 40 50 1221750802205240 40 50 1221750802405260 40 50 1221750802605280 40 50 1221750802805300 40 50 1221750803005350 40 50 1221750803505400 40 50 1221750804005450 40 50 1221750804505
Cylindric head, T-STAR plusCUT point, case hardened, slide-coated
P3J
Ø d1
Ls
LgV
Ø d k
1221
7508
0240
5 50
'!0A35DA-bichbg!8X240 Z-9.1-519T40
P3J
CU
T
corrosion protection
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
Thre
ad c
lose
to h
ead
Other lengths, head shapes and surfaces on request.
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
Lengthfull thread LgV
BIT size
T
SPAXBOX
[pieces]
0 0.33 101
Follow up information from page 19.
– 10 times greater anti-corrosion protection compared with yellow zinc plating
Corrosion resistance comparison using the
salt spray test (DIN EN ISO 9227:2006 –
Corrosions tests in artificial atmospheres)
blue zinc plated
yellow zinc plated
coating
Corrosion resistance relative to yellow zinc plating
WIROX coated screw is an economic alternative to stainless steel with added strength.
in compliance with selected technical directives
Technical directives
RoHS – EC Directive 2002/95/EG“Restricted use of hazardous materials”
Complies with RoHS
REACH – Act (EC) No. 1907/2006“Registration, assessment, approval and restriction of chemical materials”
Complies with REACH
DIN EN 1670 – corrosion resistance of architectural hardware
Class 5 – Exceptional safety
EU Directive 88/378/EWG – toys safety and DIN EN 71-3 – toys safety
Complies with the specifications
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
8.0 80 47 40 50 0191750800805
Ø dk = 15.1 mm
100 57 40 50 0191750801005120 70 40 50 0191750801205140 80 40 50 0191750801405160 80 40 50 0191750801605180 80 40 50 0191750801805200 80 40 50 0191750802005220 80 40 50 0191750802205240 80 40 50 0191750802405260 80 40 50 0191750802605280 80 40 50 0191750802805300 80 40 50 0191750803005320 80 40 50 0191750803205340 80 40 50 0191750803405360 80 40 50 0191750803605380 80 40 50 0191750803805400 80 40 50 0191750804005450 80 40 50 0191750804505
2425
MULTI Head
P3J
Flat countersunk head, T-STAR plusMULTI Head and 4CUT, case hardened, slide-coated
Practical screwing aid see page 13
Other lengths, head shapes and surfaces on request.
T-STAR plus
4CUT and ground serrations
4CUT
90°
Ls
LgT
Ø d
1
Ø d k
50
'!0A35DA-bhjadh!T40
0191
7508
0240
5
8X240 Z-9.1-449
corrosion protection
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
SPAX No.Dimensions [mm] Packaging unit
Thread Ø
d1
Lengthtotal
Ls
Lengthpartial thread LgT
BIT size
T
SPAXBOX
[pieces]
8.0 80 70 ■ 40 50 0251750800805
Ø dk = 20 mm
100 80 ■ 40 50 0251750801005120 80 ■ 40 50 0251750801205140 80 ❑ 40 50 0251750801405160 80 ❑ 40 50 0251750801605180 80 ❑ 40 50 0251750801805200 80 ❑ 40 50 0251750802005220 80 ❑ 40 50 0251750802205240 80 ❑ 40 50 0251750802405260 80 ❑ 40 50 0251750802605280 80 ❑ 40 50 0251750802805300 80 ❑ 40 50 0251750803005320 80 ❑ 40 50 0251750803205340 80 ❑ 40 50 0251750803405360 80 ❑ 40 50 0251750803605380 80 ❑ 40 50 0251750803805400 80 ❑ 40 50 0251750804005450 80 ❑ 40 25 0251750804505
P3J
Washer head, T-STAR plus4CUT, case hardened, slide-coated
Other lengths, head shapes and surfaces on request.
T-STAR plus
4CUT and ground serrations
4CUT
Ls
Lg
Ø d
1
Ø d k
50
'!0A35DA-bhiibi!T40
0251
7508
0240
5
4CU
TP
3J
8X240 Z-9.1-449
corrosion protection
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
4CU
T®
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Washer head
■T-STAR plus, full thread
❑T-STAR plus, partial thread
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
BIT size
T
SPAXBOX
[pieces]
Lengththread Lg
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
2627
Fields of application: For use outside (e.g. carports, playground
equipment, pergolas, porches, bridges, bridge plank flooring, balconies)
Fastening of sheet metal (e.g. solar roof hooks)
Securing of carpenter wood connections (e.g. offsets)
Outer diameter 6, 8, 10 and 12 mm
160–550 mm total length
50–200 mm total length
60–140 mm total length
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
Washer head
T-STAR plus6.0 60 56 ■ 30 100 0257000600605
Ø dk = 13.6 mm
80 61 ■ 30 100 0257000600805100 61 ❑ 30 100 0257000601005120 68 ❑ 30 100 0257000601205140 68 ❑ 30 100 0257000601405
Stainless steel A2 1.4567
Washer head, T-STAR plus4CUT, slide-coated
Other lengths, head shapes and surfaces on request.
2829
4CUT and ground serrations
Ls
Lg
Ø d1
Ø d k
100
'!0A35DA-bidagf!T30
0257
0006
0140
5
6X140 Z-9.1-235
INOXSTAINLESS STEEL
1.45
67
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
AIS
I 304
4CU
T®
■T-STAR plus, full thread
❑T-STAR plus, partial thread
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
BIT size
T
SPAXBOX
[pieces]
Lengththread Lg
The stainless steel assortment for timber construction:In the long term, galvanised protective coatings usually do not sufficiently protect steel screws against corrosion in outdoor areas.
The SPAX stainless steel offers protection against corrosion.
It is particularly well suited for use outdoors. Wherever you need to make secure bolted joints: SPAX stainless steel.
Advantages of a washer head compared to a countersunk head:Better tightening of connections also of warped boards.
Washer head guarantees higher beam supporting forces and allows savings with regard to piece numbers and working time.
Easy bolting of steel parts and sheet metal to wood without prior counter boring of the bore hole.
Improved gripping effect of the head when bolting thin sheet metal.
– Stainless steel
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
3031
8.0 50 46 ■ 40 50 0257000800505
Ø dk = 20 mm
60 56 ■ 40 50 0257000800605 80 70 ■ 40 50 0257000800805100 80 ■ 40 50 0257000801005120 80 ■ 40 50 0257000801205140 80 ❑ 40 50 0257000801405160 80 ❑ 40 50 0257000801605180 80 ❑ 40 50 0257000801805200 80 ❑ 40 50 0257000802005
Stainless steel A2 1.4567
Washer head, T-STAR plus4CUT, slide-coated
Other lengths, head shapes and surfaces on request.
Washer head
T-STAR plus
4CUT and ground serrations
4CUT
Ls
Lg
Ø d1
Ø d k
50
'!0A35DA-bhhjba!T40
0257
0008
0160
5
8X160 Z-9.1-449
INOXSTAINLESS STEEL
1.45
67
0672
-CPD
-I 14
.12.17
ET
A-1
2/01
1413
Do
P 1
AIS
I 304
4CU
T®
■T-STAR plus, full thread
❑T-STAR plus, partial thread
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
BIT size
T
SPAXBOX
[pieces]
Lengththread Lg
10.0 160 50 50 1208001001605
Ø dk = 18.6 mm
200 50 50 1208001002005220 50 50 1208001002205240 50 50 1208001002405260 50 50 1208001002605280 50 50 1208001002805300 50 50 1208001003005350 50 50 1208001003505400 50 50 1208001004005
12.0 400 50 25 1208001204005
Ø dk = 18.6 mm
450 50 25 1208001204505500 50 25 1208001205005550 50 20 1208001205505
Thre
ad c
lose
to h
ead
Thre
ad c
lose
to
hea
dFlat countersunk head, T-STARMilled rips, CUT point, slide-coated
CUT point and SPAX typical ground serrations
Stainless steel A4 1.4578
Flat countersunk head T-STAR with milled ribs
Ø d190°
Ls
LgV
Ø d k
10X240
Senkkopf mit Fräsrippen T 50
Art
.: 12
0800
1002
405
50 S
tück
'!0A35DA-bhigij!
INOXSTAINLESS STEEL
A4
CU
T
Z-9.1-519
1.45
78
0672-CPD-I 14.12.17
ETA-12/011413DoP 1
AIS
I 316
Other lengths, head shapes and surfaces on request. NEW!
T-STAR plus T50
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
Lengthfull thread LgV
BIT size
T
SPAXBOX
[pieces]
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
3233
Ice sport hall Erfurt www.gunda-niemann-stirnemann-halle.de
Z-9.1-832
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
800–2,200 mm total length
3,000 mm total length
SPAX threaded rodThe alternative for transverse reinforcement
The features at a glance: Transverse reinforcement in cases of large wooden
constructions (usually made of gluelam)
Ideal replacement for glued threaded rods
Ideal also for use in subsequent refurbishment at building site, irrespective of the outside temperature
Approved by German and European building authorities under licensing number Z-9.1-832 and ETA-12/0114
Possible to work overhead
No glue necessary: saving time and money
Less sensitive to adverse conditions (damp, temperature, …)
Pre-drilling to core diameter with 12 –13 mm
Low screwing-in torque
Galvanised and additional sliding coating
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
16.0 3,000 10 35616000201011
Other lengths on request.
Blue zinc plated A2J
3435
Ls
Ø d
1
For pre-drilling, the following drills having a diameter of 12 to 13 mm are recommendable:
FAMAG, Remscheid: Auger BIT
WOODTEC FANKHAUSER, CH-Vordemwald: Deep hole drill flushed with pressurised air
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
Shaft ring
[piece]
SPAX threaded rodWithout head, slide-coated
50019009000111 piece in carton
SPAX No.Sales unit
SPAX-screw-sleeve, wrench size SW 11For threaded rods without head
16.0 800 SW 22 25 35616000108011
Ø dk = 26 mm
1,000 SW 22 25 356160001010111,200 SW 22 25 356160001020111,400 SW 22 25 356160001030111,600 SW 22 25 356160001040111,800 SW 22 25 356160001050112,000 SW 22 25 356160001060112,200 SW 22 25 35616000107011
Ls
LgV
Ø d
1
Ø d k
Z-9.1-832
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
SPAX threaded rods
Hexagonal head SW 22 mm Outer Ø d1 = 16 mm Core -Ø d3 = 12 mm
What must be observed during processing:
The drill BIT can deviate in case of very narrow components and long drilled holes. If no experience is available in the factory, please check in advance.
The following machines are recommended for screwing-in:
PROTOOL DRP 32-4, BOSCH GBM 32-4, FEIN angle screwing machine Mammut SCW 16-6, MAKITA angle screwing machine DA 4301.
Shortening to desired length possible.
Use drill BITs with Ø 12–13 mm.
Pre-drilling
Screwing in
Ready!
Thre
ad c
lose
to h
ead
Other lengths on request.
Dimensions [mm] Packaging unit SPAX No.
Thread Ø
d1
Lengthtotal
Ls
Lengthfull thread LgV
Wrenchsize
Shaft ring
[piece]
SPAX threaded rodWith hex head, slide-coated
Blue zinc plated A2J
0672-CPD-I 14.12.17ETA-12/0114
DoP 113
3637
Example applications
Partial threadWall connection, wood frame construction
Economic alternative to coach screw conf. to DIN 571
Safe tightening, e.g. of wall fixtures
No pre-drilling necessary (wood-dependent)
67% higher to hold down forces than screws
Connection rafter to purlin
Fastening the rafters. With the washer head screw even heavily twisted rafters can be tightened
High wind draft protection
Does without rafter purlin anchors
Z-9.1- 511 – approved by building authorities for fastening rooftop insulation systems
Washer head ensures higher head to hold down forces, allowing for larger screw distances
Free of charge calculation software
Static calculation service
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Full thread Lateral pressure reinforcement
Simple and universal opportunity for increasing the bearing pressure through full thread screws
Apply computing procedure according to Z-9.1-519 or ETA-12/0114
Lateral tension reinforcements conforming to DIN 1052:2010-12 or ETA-12/0114
Safe alternative to glued on reinforcing boards and glued in threaded bars
Can be performed by any carpentry business
No gluing license necessary
Can be safely applied on site even after construction (e.g. when renovating)
Flexibly connected bending beams
High stiffness of the overall cross section through angularly aligned screws (cross-sectional strengthening)
Particularly of interest in the field of renovation
Cost-effective alternative to:
Bolt connections
Formed sheet metal parts
Laterally reinforced through:
– glued on reinforcement panels or – glued in threaded rods
National Technical Approval
Approval No.:
Z-9.1-449
Applicant:SPAX International GmbH & Co.KGKölner Straße 71-7758256 Ennepetal
Approved Product:
SPAX® screwsfor fastening timber
National Technical Approval has herewith been granted for the above named product.This National Technical Approval comprises 13 pages and 17 appendices. This National Technical Approval replaces the National Technical Approval No. Z-9.1-449 da-ted 11th March 2011. The product was fi rst granted National Technical Approval on 2nd March 1999.
Period of validity:from:
to:
1st August 20121st August 2017
Approval body for construction products and const-ruction types
Construction testing institute
A public institution jointly supported by the federal and state governments
Member of EOTA, UEAtc and WFTAO
Date:
31/07/2012
Reference number:
I 56-1.9.1-449#11
Translation of the original German document; translation not examinedby Deutsches Institut für Bautechnik
Translation of the original German document; translation not examinedby MPA (Otto-Graf-Institut · Materialprüfungsanstalt · Universität Stuttgart)
CERTIFICATE OF COMPLIANCENo. ÜZ-BWU03-I 14.12.19
Pursuant to Article 25, Paragraph 2, No. 2 of the Building Regulations of the State of North RhineWestphalia (BauO-NRW) as per version dated 1st March 2000, we hereby certify that
the building product: SPAX screws for fastening timber
manufactured at the plant in: 58256 Ennepetal, Germany
of: SPAX International GmbH & Co. KG Kölner Strasse 71-77 58256 Ennepetal
complies, in accordance with the results of the internal production inspection and the external production inspection carried out by the Materialprüfungsanstalt (Material Testing Laboratory) of the University of Stuttgart, with the provisions of the
general building authority approval
Z-9.1-449 of the Deutsches Institut für Bautechnik, Berlin.
In accordance with the Conformity Regulations, the company is thus entitled to apply the markof conformity (Ü mark) to the building product manufactured at the plant in
58256 Ennepetal, Germany
Stuttgart, 01.03.2010 Materialprüfungsanstalt(Material Testing Laboratory)
Universität StuttgartTimber Construction Dept.
Certifi cation Dept.
Dr Simon AicherAcademic Director
Head of Certifi cation Department
Materialprüfungsanstalt · Universität Stuttgart, Pfaffenwaldring 32, 70569 Stuttgart
3839
National German Approval Conformity certificate
Approval document ETA Conformity certificate Declaration of Performance (DoP)
Revision level B of 15.08.2014Annexes 1 to 45 have been amended accordingly, and their revision level entered in the footer as follows:
Declaration of Performance (DoP)No. DoP 1 1/3
Unique identification code of the product-type
SPAX
1.
Type, batch or serial number or any other element allowing identification of the construction product as required pursuant to Article 11(4) CPR
Article Number and EAN-Code see table
2.
Intended use or uses of the construction product, in accordance with the applicable harmonised technical specification, as foreseen by the manufacturer
Self-tapping screws for use in timber structures
3.
Name, registered trade name or registered trade mark and contact address of the manufacturer as required pursuant to Article 11(5)
SPAX International GmbH & Co. KG Kölner Straße 71-77 D-58256 Ennepetal
Germany
4.
System or systems of assessment and verification of constancy of performance of the construction product as set out in Annex V
System 2+
6.
Notified body
Materialprüfungsanstalt der Universität Stuttgart MPA Stuttgart - Otto-Graf-Institut (FMPA)
Postfach 80 11 40 DE-70511 Stuttgart
Germany
Reference number of the European Technical Assessment
ETA-12/0114
Reference number of the European Assessment Document
CUAP 06.03/08
EC-Certificate of conformity
0672 – CPD – I . 14 12.17
Not relevant
Name and identification number of the Technical Assessment Body
ETA-Danmark A/S Kollegievej 6
DK-2920 Charlottenlund
8.
5.
Not relevant7.
ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk
MEMBER OF EOTA
Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products
European Technical Approval ETA-12/0114
This ETA replaces the previous ETA with the same number and validity from 2012-09-05 to 2017-07-17
Trade name: SPAX self-tapping screws
Holder of approval: SPAX International GmbH & Co. KG Kölner Strasse 71-77 DE-58256 Ennepetal Tel. +49 23 33 799-0 Fax + 49 23 33 799-199 Internet www.spax.com
Generic type and use of con-struction product:
Self-tapping screws for use in timber structures
Valid from: to:
2013-06-26 2017-07-17
Manufacturing plant: SPAX International GmbH & Co. KG Kölner Strasse 71-77 DE-58256 Ennepetal
This European Technical Approval contains:
97 pages including 6 annexes which form an integral part of the document
Ü-Logo by SPAX according to General Technical ApprovalsFor SPAX different General Technical Approvals are available regulating their use as building and construction product.
Please note that you not only need an approval for the product but also a Conformity certificate by the respective inspecting body for each manufacturing plant!
This certificate attests that the products correspond to the approval and that a proper self monitoring and external quality control are existant. Therefore, we as the producer, are qualified to supply our products with the Ü-Logo.
Of course, SPAX has all these documents on hand. From our certificate of com-pliance, which is accessible at any time (i.e. as a download on www.spax.com or on demand), you can see that SPAX is produced in Germany.
Quality Made in Germany!
– Certificates
CE marking according to the European Technical Approval ETA-12/0114Quality control and adherence to the applicable regulations; these are the fun-damental elements which set SPAX International products apart from the rest. We constantly strive to fulfil this.
The CE marking alone does not change the original product features. However, it offers you as a specialist dealer and user an additional advantage in the form of Europe-wide applicability.
With transparent documentation, you are able to recognise the manufacturer immediately.
SPAX Made in Germany!
Ü-Logo
CE marking
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
Product test acc. to TN-Standard A75-S01
8
Made in Germ
any
TÜV Nord CerT GmbH
4560
/ 12
/ 14
/ D / O
RT
SPAX International GmbH & Co. KG
ALTeNLoH, BrINCK & Co - GrUPPeKÖLNer STrASSe 71-77 · d-58256 eNNePeTAL · GerMANY
TeL + 49-23 33-799-0 · FAX + 49-23 33-799-199 [email protected] · www.spax.com
The quickest way to us: