1
Contact Probes
Contact probes differ depending on the product, function and device to be tested, so a variety of probes are available. Select the proper probe that avoids damaging the device under test while ensuring reliable contact.
the product, function and device to be tested, so a variety of probes are available. Select the proper probe that avoids damaging the device under test while ensuring reliable contact.
2
Probe Pressure(at 2/3 stroke)
3 : 2.38N (1171- 433 only: 2.16N) (at 4.2mm)4 : 3.11N (high-probe-pressure type) (at 4.2mm)6 : 3.68N (high-probe-pressure type) (at 4.2mm)8 : 1.77N (at 4.0mm)9 : 1.96N (at 3.0mm)A : 2.26N (at 4.0mm)
1171-n n Note: Valid combinations of n characters are as follows:
Class (supported pitch)
4 : Internal-Spring Two-Piece Type (2.54 mm pitch)
5 : Internal-Spring Two-Piece Type (1.27 mm pitch)
6 : Internal-Spring One-Piece Type (1.27 mm pitch)
Stock No. Tip Shape Probe Pressure
Size Remarksøa øb
1171-618 Needle 1.77N 0.581171-628 Head-less Crown 0.581171-678 Chisel 0.80 for through hole
1171-688 Reduced Crown,Small 0.251171-698 Reduced Crown,Large 0.201171-6A8 Blade Lead-free
recommended
1171-6B8 Chisel,Small for Minibea1171-6C8 Chisel,Large 1.00 Large-diameter
through hole
1171-6E8 Reduced Headless Crown 0.28
u Internal-Spring Two-Piece Type (1.27 mm pitch, high-probe-pressure type)
Stock No. Tip Shape Probe Pressure
Size Remarksøa øb
1171-61A Needle 2.26N 0.581171-62A Head-less Crown 0.581171-67A Chisel 0.80 for through hole
1171-68A Reduced Crown,Small 0.251171-69A Reduced Crown,Large 0.201171-6AA Blade Lead-free
recommended
1171-6BA Chisel,Small for Minibea1171-6CA Chisel,Large 1.00 Large-diameter
through hole
1171-6EA Reduced Headless Crown 0.28
u Internal-Spring One-Piece Type (1.27 mm pitch)
Stock No. Tip Shape Probe Pressure
Size Remarksøa øb
1171-519 Needle 1.96N 0.691171-529 Head-less Crown 0.691171-579 Chisel for through hole
1171-589 Reduced Crown,Small 0.201171-599 Reduced Crown,Large
Internal-Spring Probes
Stock No. Tip Shape Probe Pressure
Size Remarksøa øb
1171-413 Needle 2.38N 1.001171-423 Head-less Crown 1.001171-433 3-Point Needle 2.16N 1.801171-443 Crown 2.38N 1.501171-453 Serrated,Small 1.37 for washing boards
1171-463 Serrated,Large 1.801171-473 Chisel 1.37 for through hole
1171-483 Reduced Crown,Small 0.251171-493 Reduced Crown,Large 0.301171-4A3 Blade Lead-free
recommended
1171-4B3 Chisel,Small for Minibea1171-4C3 Chisel,Large 1.80 Large-diameter
through hole
1171-4D3 Cup 1.37 for connector pins
u Internal-Spring Two-Piece Type (2.54 mm pitch, high-probe-pressure type)
Stock No. Tip Shape Probe Pressure
Size Remarksøa øb
1171-414 Needle 3.11N 1.001171-424 Head-less Crown 1.001171-434 3-Point Needle 3.02N 1.801171-444 Crown 3.11N 1.501171-454 Serrated,Small 1.37 for washing boards
1171-464 Serrated,Large 1.801171-474 Chisel 1.37 for through hole
1171-484 Reduced Crown,Small 0.251171-494 Reduced Crown,Large 0.301171-4A4 Blade Lead-free
recommended
1171-4B4 Chisel,Small for Minibea1171-4C4 Chisel,Large 1.80 Large-diameter
through hole
1171-4D4 Cup 1.37 for connector pins
u Internal-Spring Two-Piece Type (2.54 mm pitch, high-probe-pressure type)
Stock No. Tip Shape Probe Pressure
Size Remarksøa øb
1171-416 Needle 3.68N 1.001171-426 Head-less Crown 1.001171-436 3-Point Needle 1.801171-446 Crown 1.501171-456 Serrated,Small 1.37 for washing boards
1171-466 Serrated,Large 1.801171-476 Chisel 1.37 for through hole
1171-486 Reduced Crown,Small 1.371171-496 Reduced Crown,Large 0.301171-4A6 Blade Lead-free
recommended
1171-4B6 Chisel,Small for Minibea1171-4C6 Chisel,Large 1.80 Large-diameter
through hole
1171-4D6 Cup 1.37 for connector pins
u Internal-Spring Two-Piece Type (2.54 mm pitch)
u Internal-Spring Two-Piece Type (1.27 mm pitch)
Tip Shape
1 : Needle 2 : Head-less Crown
3 : 3-Point Needle
4 : Crown
5 : Serrated,Small
6 : Serrated,Large
7 : Chisel
8 : Reduced Crown,Small
9 : Reduced Crown,Large
A : Blade
B : Chisel,Small
C : Chisel,Large
D : Cup
E : Reduced Headless Crown
For 1220 • 1105 • (1101 • 1102 • 1120 • 1121)
1171 Series
● Internal-Spring Probes List
3
1171-6 8 (k For 1171-678, dimension is +1.0 mm)
1171-4 (except 1171-4 3 )
● Tip Shape
Needle 1171- 1
Reduced Crown,Large
1171- 9 Reduced Crown,Small
1171- 8
Chisel 1171- 7
Serrated,Large 1171-4 6 3
Serrated,Small1171-4 5 3
Crown1171-4 4
3-Point Needle1171-4 3
Head-less Crown1171- 2
1.6
2.002.00
2.0 2.0
øaøa
k39.5
k8.0
ø0.58 ø0.71
øa
øb øb
øaøa
øbø1.80
øa
øa øa
ø1.50 ø1.37
øa
ø1.8 or lower
Tip 60˚
1.6 6.4
24.913.0
37.9
ø1.0
+0ø1.38 −0.02
1171-4 3
49.413.2
6.0 7.2 29.2 7.0
+0ø0.92 −0.02ø1.10ø0.69 ø0.80
1171-5 9
37.9
8.4 29.5
ø1.0 +0ø1.38 −0.02
Tip 45˚
Blade1171- A
Chisel,Small1171- B
Chisel,Large1171- C
Cup1171- D
Reduced Headless Crown1171- 6 E
Chisel,Large 1171- C
1.27-mm Probes
For both1.27-mm and 2.45-mm probes
øb øa øa øa
80° 80°60°
60°
øb
øb
ø1.20
2.00
ø0.58ø0.58
60°
60°
1.00
ø0.28
ø1.00
2.00
Reduced Crown,Small 1171- 6 8
ø0.58
60°ø0.25
● External Dimensions
4
1161-6 3 • 1161-7 3 (Resin Sleeve)
Probe Pressure (when using 6 mm stroke)2 : 1.96N3 : 2.94N
● External-Spring Probes List
1161-5 2 (Metal Sleeve)
58
øc øb +0øa −0.02
Class (supported pitch)
5 : External-Spring 2.00mm (Metal Sleeve)
6 : External-Spring 3.50mm (Resin Sleeve)
7 : External-Spring 2.54mm (Resin Sleeve)
External-Spring Probes
Needle 3-Point NeedleHead-less Crown
52.2
øc ø1.16 øb øa ø1.0
21.7 30.56.0 24.0 6.5
221
36515
ø1.0
øC øCøC
Probe pressure is indicated in international (SI) units (Newtons, N). The relationship between gf and N is as follows:1gf 9.8mN 0.0098N 1N 102gf
Stock No. supported pitch
Tip Shape Probe Pressure Sizeøa øb øc
1161-512 2.00 Needle 1.96N 1.5 1.7 1.161161-522 Head-less Crown 1.161161-532 3-Point Needle 1.8 or lower1161-613 3.50 Needle 2.94N (3.0) 3.3 1.71161-623 Head-less Crown 1.71161-633 3-Point Needle 2.9 or lower1161-713 2.54 Needle (2.0) 2.3 1.031161-723 Head-less Crown 1.031161-733 3-Point Needle 1.8 or lower
For 1220 • 1105 • (1101 • 1102 • 1120 • 1121)
1161 Series
1161- Note: Valid combinations of characters are as follows:
Tip Shape1 : Needle 2 : Head-less Crown
3 : 3-Point Needle
Note: ( ) indicates reference size
● External Dimensions
● Tip Shape
5
Fine-Pitch Probes
Special Probes
(63)Note: for insulating coatings1
79.3
7 (8.3)
Needle 1161-801
Reduced Crown,Small 1161-802
Flat1161-803
ø0.15 ø0.15
ø0.3
ø0.2
20°
20°60°
60°
ø1.1
ø0.6
ø0.33 ±0.01 +0ø0.92 −0.02
1161-201 (Serrated tip, single pin)
1161-202 (ø 5.7 7-pin)
1161-203 (ø 7.8 12-pin)
1161-206 (Radius tip, single pin)(Special specification)
ø3.2ø1.0
ø1.0ø1.75
ø1.75
ø1.47
ø1.47
ø5.7
ø7.8
53
2
2
6737.9
67
29.5
8.4
8.4
33.3
24.9
ø1.75 ±0.01 ø1.47 ±0.01
+0ø1.38 −0.02
+0ø1.38 −0.02
1161-205 (Radius tip, single pin)(Special specification)
1161-8 0
64.9
6.83
0.5 M4 P = 0.7
ø1.8 2
ø3.2
1161-207 (2-Step Probe)(Special specification)
Stock No. Tip Shape1161-801 Needle
1161-802 Reduced Crown,Small
1161-803 Flat
Tip Shape
● Tip Shape
buckling load Approx. 0.96N
6
ø1.47 ø1.0ø1.85
A
39
+0ø1.67 −0.02
1161-101 (For external-spring) A = 61 B = 28 (mm)1161-102 (For internal-spring) A = 53 B = 20 (mm)1161-103 (For internal-spring, movable guide pin specification) A = 67 B = 28 (mm)
1171-001 A = 0.2 (mm) 1171-002 A = 2.5 (mm)1171-003 A = 4.5 (mm)1171-004 A = 8.1 (mm)(For 1171-4 Series)
1161-011(for 1.27-mm internal spring)
1171-005(For 1171-4 Series)
1171-010 A = 4.5 (mm)
1171-011 A = 7.5 (mm)(For 1171-6 8 Series)
1171-020 (For 1171-6 8 Series)Use only when mixed with fine-pitch probes
* Dimensions are for 1171-010 A = 4.5.1171-011 A 7.5 (*) dimensions are +3 mm.
Flat Pins
Socket
Wiring
1077 20 50 30
Hole diameter (1.0
Approx. 500
Approx. 600
Heat shrink tubing Wire leadCore conductor
ø0.8ø0.99
40.7*
9.7*A
ø1.83 ø1.0
30.23
7.625
ø1.75 ø1.47ø4.0
A
B
5
ø0.92
+0ø3.45 −0.02
Note: Tip head material is resin (POM).
1161-001 (with ø 1.0 pin socket)(For both external spring and 2.54-mm internal spring)
1161-012 ((1.0 replacement wiring)(for 1.27-mm internal spring)
ø0.99 ø0.92 ø0.8
72.8
41.84.5
Movable Guide Rods99
2821
ø6ø7
øA+1
.0øA
ø1
1160A613 (Pin)1160A616 (Sleeve and Spring)1160A617 (Single-Unit Type)
7
+0ø1.67 −0.02
Heat shrink tubingWire lead
Internal spring (1.27) Probeø1.0
Internal spring (1.27) Probe Wire leadCore conductor
*Specify the diameter A when ordering 1160A613 and 1160A617 probes.
*The above diagram pictures an 1160A617 integrated probe (160A613 + 1160A616).
7
Stock No. Class Remarks
1161-512 Needle 1161-522 Head-less Crown 1161-532 3-Point Needle 1161-613 Needle 1161-623 Head-less Crown 1161-633 3-Point Needle 1161-713 Needle 1161-723 Head-less Crown 1161-733 3-Point Needle ● Fine-Pitch Probe (Order in units of 10 pieces)
Stock No. Class Remarks1161-801 Needle 1161-802 Reduced Crown,Small 1161-803 Flat ● Movable Guide Rods
Stock No. Class Remarks
1160A-613 Pin 1160A-616 Sleeve and Spring 1160A-617 Single-Unit Type
Stock No. Tip Shape Remarks
1161-201 Serrated tip, single pin 1161-202 ø 5.7-7pin 1161-203 ø 7.8-12pin 1161-205 Radius tip, single pin 1161-206 Radius tip, single pin 1161-207 2-Step Probe ● Flat Pins (Order in units of 10 pieces)
Stock No. Class Remarks1161-101 For external-spring 1161-102 For internal-spring 1161-103 Working movable guide pin
specification ● Wiring (Order in units of 10 pieces)
Stock No. Class Remarks1161-001 With ø1.0 pin socket 1161-011 For internal-spring 1.27 1161-012 ø1.0 replacement wiring
1161 External-Spring and Miscellaneous Series
1171 Internal-Spring Series
Stock No. Tip Shape Remarks
1171-413 Needle1171-423 Head-less Crown 1171-433 3-Point Needle 1171-443 Crown 1171-453 Serrated,Small for washing boards1171-463 Serrated,Large for washing boards1171-473 Chisel for through hole1171-483 Reduced Crown,Small 1171-493 Reduced Crown,Large 1171-4A3 Blade Lead-free recommended1171-4B3 Chisel,Small for Minibea1171-4C3 Chisel,Large Large-diameter through hole 1171-4D3 Cup for connector pins1171-414 Needle 1171-424 Head-less Crown 1171-434 3-Point Needle 1171-444 Crown 1171-454 Serrated,Small for washing boards1171-464 Serrated,Large for washing boards1171-474 Chisel for through hole1171-484 Reduced Crown,Small 1171-494 Reduced Crown,Large 1171-4A4 Blade Lead-free recommended1171-4B4 Chisel,Small for Minibea1171-4C4 Chisel,Large Large-diameter through hole1171-4D4 Cup for connector pins1171-416 Needle 1171-426 Head-less Crown 1171-436 3-Point Needle 1171-446 Crown 1171-456 Serrated,Small 1171-466 Serrated,Large 1171-476 Chisel for through hole1171-486 Reduced Crown,Small 1171-496 Reduced Crown,Large 1171-4A6 Blade Lead-free recommended1171-4B6 Chisel,Small for Minibea1171-4C6 Chisel,Large Large-diameter through hole1171-4D6 Cup for connector pins
Stock No. Tip Shape Remarks
1171-618 Needle 1171-628 Head-less Crown 1171-678 Chisel for through hole1171-688 Reduced Crown,Small 1171-698 Reduced Crown,Large 1171-6A8 Blade Lead-free recommended1171-6B8 Chisel,Small for Minibea 1171-6C8 Chisel,Large Large-diameter through hole1171-6E8 Reduced Headless Crown 1171-61A Needle 1171-62A Head-less Crown 1171-67A Chisel for through hole1171-68A Reduced Crown,Small 1171-69A Reduced Crown,Large 1171-6AA Blade Lead-free recommended1171-6BA Chisel,Small for Minibea1171-6CA Chisel,Large Large-diameter through hole1171-6EA Reduced Headless Crown ● Internal-Spring One-Piece Type (1.27 mm pitch) (Order in units of 10 pieces)
Stock No. Tip Shape Remarks
1171-519 Needle 1171-529 Head-less Crown 1171-579 Chisel for through hole1171-589 Reduced Crown,Small 1171-599 Reduced Crown,Large ● Socket (Order in units of 10 pieces)
Stock No. Class Remarks
1171-001 A=0.2 (see illustration) 1171-002 A=2.5 (see illustration) 1171-003 A=4.5 (see illustration) 1171-004 A=8.1 (see illustration) 1171-005 With (1.0 terminal 1171-010 A=4.5 (see illustration) 1171-011 A=7.5 (see illustration) 1171-020 For mixing with fine pitch ● Internal-Spring Pin Insertion/Extraction ToolStock No. Class Remarks1171-100 Tool
● Internal-Spring Two-Piece Type (2.54 mm pitch) (Order in units of 10 pieces)
● External-Spring Probes (Order in units of 10 pieces) ● Special Probes (Order in units of 10 pieces, except 1161-202, -203 and -207)
● Internal-Spring Two-Piece Type (1.27 mm pitch) (Order in units of 10 pieces)
8For 1110 • 1111 • 1112 • 1114 • 1240
1172 Series
1172-0
1172-1
For 1110
For 1111 • 1112 • 1114 • 1240
Tip Shape
Stock No. Tip Shape Probe Pressure1172-01 Needle
1.50N1172-02 3-Point Needle
1172-03 Head-less Crown
1172-04 Reduced Crown,Smal
1172-05 Chisel 1.18N1172-06 Needle (HP) 1.50N
1172-0 (Except for the 1172-06)
1172-06
1154-0❑
1172-1
Stock No. Size a For arm1154-01 124mm For L and R ARM
1154-02 174mm
● Wiring (For 1172-01~05)
ø4.0ø1.18
Hole diameter (1.0
ø4.0
ø4.0
ø1.16
ø1.16
52.5
22
48.5
18
170
a
Heat shrink tubing
a
14.0
50.5
Core conductorWire lead
For all of the above products, the probe pressure is 1.35N (when using a 2mm stroke)*WC: Super-hard type*1172-24/25/26: Extra-fine super-hard type (available soon)
Probe Pressure(at 3mm stroke)*The test cable is soldered in place.
*The test cable is soldered in place.
Tip Shape • Cable length
1172-4
Four-terminal measuring function
Cable length
n 4-Terminal Probe
ø4ø2
ø1.06
a14.1
59
1172-4
Stock No. Tip Shape Size a For model For armL M R
1172-11 Needle 120mm 1111•11121172-121172-12WC1172-24
Needle 280mm1111•1112
1240-01,02
1172-13 Reduced Crown,Small 120mm 1111•1112
1172-14 Reduced Crown,Small 280mm
1111•11121240-01,02
1172-15 Chisel 120mm 1111•1112
1172-16 Chisel 280mm 1111•11121240-01,02
1172-171172-17WC1172-25
Needle 195mm1114
1240-01,02
1172-181172-18WC1172-26
Needle 60mm 1240-03
Stock No. Size a For model
1172-41 180mm (For L and R ARM) 1111 · 1112 · 11141172-42 290mm (For M ARM) 1111 · 11121172-43 290mm (For L and M ARM) 1240-01,021172-44 190mm (For R ARM) 1240-01,021172-45 56mm (For ALL ARM) 1240-03
1172-2
ø4.0ø1.0 b
14.0
53..0
28.8
*The test cable is soldered in place.
1114 : Shared for all arms
clamp tubes
Size b1172-24: 290 mm (with 2 clamp tubes)1172-25: 205 mm (with 2 clamp tubes)1172-26: 90 mm (with notch in holder; no clamp tubes)
ø0.15 ø0.5 ø1.045° 6°
8.8
1 Can be used with a cable length of 195 mm.
9
1172 Series
Stock No. Tip Shape Remarks
1172-01 Needle 1172-02 3-Point Needle
1172-03 Head-less Crown
1172-04 Reduced Crown,Smal
1172-05 Chisel
1172-06 Needle ( High-precision type )1154-01 Wiring 124mm1154-02 Wiring 174mm
● For 1110
● For 1111 • 1112 • 1114 • 1240
● 1172 Series Tip Shape
ø1.8
ø0.25
ø1.37
Tip 45˚
1.6 2.0
Needle 3-Point Needle Reduced Crown,Smal ChiselHead-less Crown
● Four-terminal measuring function
Stock No. Class Remarks1172-41 4-Terminal Probe
1111 • 1112 • 1240 (For L and R ARM)1114 (For ALL ARM)
1172-42 4-Terminal Probe 1111 • 1112 • 1240 (For M ARM)
1172-43 4-Terminal Probe 1240-01,02 (For L and M ARM)
1172-44 4-Terminal Probe 1240-01,02 (For R ARM)
1172-45 4-Terminal Probe 1240-03 (For ALL ARM)
Stock No. Tip Shape Remarks
1172-11 Needle
1172-12 Needle
1172-12WC Needle
1172-13 Reduced Crown,Small
1172-14 Reduced Crown,Small
1172-15 Chisel
1172-16 Chisel
1172-17 Needle
1172-17WC Needle
1172-18 Needle
1172-18WC Needle
1172-24 Needle
1172-25 Needle
1172-26 Needle
*WC: Super-hard type*1172-26/27/28: Extra-fine super-hard type (available soon)
(Order in units of 10 pieces)
(Order in units of 10 pieces)
(Order in units of 10 pieces *1172-12WC/-17WC/-18WC and 1172-24/-25/-26: Order in units of 1)
10● Tip Shape List
1171-4 1 Needle
1171-4 2 Head-less Crown
1171-4 3 3-Point Needle
1171-4 4 Crown
1171-4 5 Serrated,Small
1171-4 6 Serrated,Large
1171-4 7 Chisel
1171-4 8 Reduced Crown,Small
1171-4 9 Reduced Crown,Large
1171-4 A Blade
1171-4 B Chisel,Small
1171-4 C Chisel,Large
1171-4 D Cup
1171-6 1 Needle
1171-6 2 Head-less Crown
1171-6 7 Chisel
1171-6 8 Reduced Crown,Small
1171-6 9 Reduced Crown,Large
1171-6 A Blade
1171-6 B Chisel,Small
1171-6 C Chisel,Large
1171-6 E Reduced Headless Crown
1161-8 0 1Needle
1161-8 0 2Reduced Crown,Small
1161-8 0 3Flat
11
Pin Insertion/Extraction Tool
1171-100 (Pin Insertion/Extraction Tool)
SIP Body
For 1.27-mm insertion
For 2.54-mm insertion For 2.54-mm extraction
For 1.27-mm extraction
Cap
Pin Insertion/Extraction Tool (actual size)
12
HEAD OFFICE : 81 Koizumi, Ueda, Nagano, 386-1192, JapanTEL +81-268-28-0562 / FAX +81-268-28-0568 E-mail: [email protected]
1160E4-94B
DISTRIBUTED BY
All information correct as of Apr.9, 2009. All specifications are subject to change without notice.
HIOKI USA CORPORATION :6 Corporate Drive, Cranbury, NJ 08512 USATEL +1-609-409-9109 / FAX +1-609-409-9108E-mail: [email protected]
HIOKI E.E.CORPORATION Singapore Representative Office :12 New Industrial Road,#02-04 Thoren Technocentre,Singapore 536202TEL +65-6288-0050 / FAX +65-6282-2283E-mail: [email protected]
TKK HIOKI CO.,LTD :NO.66-8,Sec.2,Nan Kan Road,Lu-chu,Taoyuan,TaiwanTEL +886-3-311-7260 / FAX +886-3-311-8236
HIKING TECHNOLOGY CO.,LTD : 81,Su Hong Xi Road,Suzhou Industrial Park,Suzhou,P.R.CHINATEL+86-512-62560393 / FAX+86-512-62560390