Contribution of active faults in the intraplate area of Iberia to seismic hazard: The Alentejo-Plasencia Fault
Contribución a la peligrosidad sísmica de las fallas activas de la zona intraplaca de Iberia: la Falla Alentejo-Plasencia
P. Villamor 1, R. Capote 2, M.W. Stirling 1, M. Tsige 2, K.R. Berryman 1, J.J. Martínez-Díaz 2, F. Martín-González 3
1 GNS Science, PO Box 30-368, Lower Hutt, New Zealand2 Dpto. Geodinámica. Facultad de CC. Geológicas. Universidad Complutense de Madrid.
c/ José Antonio Novais, 2. 28040 Madrid, Spain. 3 Área de Geología. ESCET. Universidad Rey Juan Carlos. C/Tulipán, s/n. Móstoles, 28933 Madrid, Spain.
*Corresponding author: [email protected]
Received: 24/12/11 / Accepted: 21/04/12
AbstractWe present the earthquake potential characterisation of the Alentejo-Plasencia Fault (APF) in the intraplate area of the Iberian
Peninsula. The APF displays clear deformation of geomorphic surfaces and sediments of Neogene and younger age and, thus, we consider it to be active within the current tectonic regime. APF fault slip rate values range from 0.01 to 0.1 mm/yr with a preferred value of 0.05 mm/yr. Mw associated to fault rupture ranges from 6.6 to 8.7 using different segmentation models (segments ranging from 20 to 500 km) and various fault scaling relationships. Recurrence intervals derived from slip rate and Mw range from 10 ka to 4 Ma, with preferred values between 20 and 30 ka. Other faults in the interior of Iberia present similar values. Hazard curves pro-duced using all fault sources from the intraplate Iberia show that active faults of the intraplate Iberia do not contribute significantly to seismic hazard at short return periods typical of the building codes (~ 500 year return periods). However, they can be important contributors to hazard at critical facilities (high hazard dams, nuclear power plants, emergency response buildings) where return periods of interest may be 10,000 years or more. Our fault source characterisation is very preliminary (with large uncertainties) and further detailed studies of active faults across the whole plate boundary are required to confirm the values for the intraplate faults presented here.
Keywords: Alentejo-Plasencia Fault, active fault, intraplate Iberia, hazard assessment, Spain
ResumenEn este trabajo se presenta la caracterización del potencial sísmico de la falla Alentejo-Plasencia (APF) situada en la región intra-
placa de la Península Ibérica. La APF muestra una clara deformación de superficies geomorfológicas y sedimentos de edad neógena
ISSN (print): 1698-6180. ISSN (online): 1886-7995www.ucm.es /info/estratig/journal.htm
Journal of Iberian Geology 38 (1) 2012: 85-111http://dx.doi.org/10.5209/rev_JIGE.2012.v38.n1.39207
86 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
1. Introduction
The Alentejo-Plasencia Fault (APF; a.k.a. Messejana or Plasencia Fault; Fig. 1) is by far the longest (>500 km) tectonic structure of the Iberian Peninsula. Although there is little current seismicity directly associated with the fault (Fig. 2), its remarkable geomorphic expression sug-gests that it is potentially active. In several low to moder-ate seismicity settings, large earthquakes have occurred on structures that, prior to rupture, were not identified as active (e.g.: the 1988 Tennant Creek Earthquake in cen-tral Australia; Crone et al.,. 1992; and the 2010 Darfield Earthquake, South Island, New Zealand; Quigley et al., 2010; 2012). Subsequent studies on those faults suggest that some may not have moved for tens of thousands to hundreds of thousands of years prior to the historic event (Crone et al., 1992; Villamor et al., 2011; 2012). A long fault rupture recurrence time, together with fault scarp erosion or burial processes that are faster than the slip rate of the fault, can lead researchers to underestimate the activity of intraplate faults. Moreover, faults with strike-slip motion that do not create significant relief or gener-ate sediments associated with their tectonic activity are likely to be assessed as inactive faults. For low slip rate faults, the historic record is always short compared to the fault rupture recurrence, and thus historic seismicity usu-ally cannot shed light on fault activity rates.
Major earthquakes associated with an active fault will pose a risk to society if rupture occurs within the design life of the structure. For typical residential buildings a 50-100 year design life is often considered and design codes often consider an earthquake with a 10% chance of occurrence in the design life as a life safety criteria (i.e., a return period of 500-1000 years; Eurocode 8, 2006). The typical return period of interest for emergency re-sponse facilities (buildings that are expected to remain serviceable through an earthquake, such as hospitals,
fire and ambulance stations, and critical infrastructure facilities such as large dams or nuclear power plants) is longer, often of the order of 10% probability of occur-rence in 250-1000 years (2500 to 10,000 year return pe-riod - note that in Spain hospitals are design from 1000 yr return period, NCSE02, 2002). The contribution to the different levels of seismic hazard (i.e., different return periods) from a individual earthquake source such as an active fault depends on the rate of activity of that fault. Therefore, is crucial to understand the rate of activity of faults in a region to be able to undertake robust seismic-resistant design.
In this study, we present a preliminary earthquake characterisation of the Alentejo-Plasencia Fault (APF), focused on the key hazard parameters of fault slip rate and maximum earthquake magnitude. In the vicinity of the APF, there are several hydro dams, a nuclear power plant and numerous heritage buildings (including some world heritage cities, UNESCO, 2011). The presence of critical facilities and world heritage buildings close to the fault necessitates an evaluation of future earth-quake potential. We have compiled data from the APF and other faults in the area (Fig. 1; Appendix 1), and undertaken an assessment of the contribution of APF and similar slow faults to the seismic hazard of central and western Iberia. Finally, we compare the rates of tectonic activity assigned to faults in the intraplate area of Iberia and consider whether the strain budget of the intraplate region compared to the total plate boundary budget is reasonable.
2. Geological setting
In the intraplate area of the Iberian Peninsula (western and central Iberia), seismicity is low to moderate with the largest instrumental record of MbLg 5.1 in 1997 (Lugo Earthquake; Martínez-Díaz et al., 2006) (Fig. 2). The
y más reciente, de modo que la consideramos una falla activa dentro del régimen tectónico vigente. Los valores de velocidad de movimiento de la APF van de 0.01 a 0.1 mm/yr con un valor preferido de 0.05 mm/yr. El valor de magnitud Mw asociada a la falla oscila entre 6.6 y 8.7 utilizando diferentes modelos de segmentación (con longitudes de segmento que van de 20 a 500 km) y varias relaciones de escala. Los intervalos de recurrencia derivados de la velocidad de movimiento y de la Mw oscilan de 10 Ka a 4 Ma, estando los valores preferidos entre los 20 Ka y los 30 Ka. Otras fallas en el interior de Iberia presentan valores similares. Las curvas de peligrosidad generadas utilizando todas las fallas-fuente de la zona intraplaca de Iberia muestran que las fallas activas de esta zona no contribuyen de forma significativa a la peligrosidad sísmica para los cortos periodos de retorno generalmente considerados en los códigos de construcción (para períodos de retorno de ~ 500 años). Sin embargo, dichas fallas pueden contribuir de modo importante a la peligrosidad sísmica para instalaciones críticas (presas de elevado riesgo, centrales nucleares, edificios de servicios de emergencia) donde los periodos de retorno de interés pueden ser de 10.000 años o más. Nuestra caracterización de la falla como fuente sismogénica es muy preliminar (presenta importantes incertidumbres) y se requieren estudios detallados adicionales de las fallas activas a lo largo de todo el límite de placa para confirmar los valores de las fallas intraplaca presentados aquí.
Palabras clave: Falla de Alentejo-Plasencia, falla activa, intraplaca ibérica, peligrosidad sísmica, España.
87Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
plate boundary lies more than 300 km SE of the study area, and relative plate motion rates between the collid-ing African and European plates is of the order of 5 mm/yr (DeMets et al., 1990; 1994). Fault activity rates in the study area are low (see below) and there have been no historic surface fault ruptures. Historical seismicity records extend back ~ 700 years, and the maximum felt earthquake intensity from an inland event is MMI IX (the Villa Franca de Xira, Portugal, Earthquake in 1531; Matínez Solares and Mezcua, 2002).
The Tertiary tectonic evolution on the central part of the Iberian Peninsula is recorded by deformation at faults bounding major sedimentary basins and sedimentary un-conformities within the basins (De Vicente et al., 2011). Capote et al. (2002 and references therein), for example,
described three different phases for the evolution of the Spanish Central Mountainous System (the main moun-tain range bounding large basins in Central Iberia): the Oligocene to Early Miocene Iberian Stage, the Middle to late Miocene Guadarrama Stage, and the Torrelaguna Stage from late Miocene to the Present. The first stage is associated with the collision between Eurasia and Iberia; the second and third with the collision between Iberia and Africa. Other authors present similar tectonic phases for surrounding areas. For example, Muñoz-Martín and De Vicente (1998) and De Vicente et al. (2004) describe two phases, Pyrenean (Eocene-Oligocene) and Betic (Middle Miocene to present) that approximately correspond to the Iberian and the Guadarrama-Torrelaguna stages de-scribed above.
Fig. 1.- Main faults of the Iberian Massif (MOPT, 1992). In red line are potencially active faults: 1) Ventaniella, 2) As-turias central (Franja Movil Intermedia), 3) Asturias Occi-dental (Espina), 4) Borde Norte de la Cuenca del Duero, 5) Sabero-Gordón, 6) León, 7) Porma, 8) Bierzo, 9) Galicia Norte, 10) Galicia Sur, 11) Galicia Central, 12) Sarria , 13) Montforte, 14) Borde Sur del Sistema Central, 15) Borde Norte del Sistema Central, 16) Seisa-Lousa, 17) Sobreira-Formosa-Pomar-Grade, 18) Ponsul, 19) Nazaré-Pombal, 20) Sierra Albarrana, 21) Las Portillas, 22) Monte Chaõ, 23) Manteigas-Vilariça-Baragança, 24) Penacova-Regua-Verín, 25) Borde Norte de la Cuenca del Guadiana, 26) Béjar, 27) Vidigueira-Moura, 28) Grandola, 29) Río Sor-Montargil, 30) Tejo Inferior, 31) Alentejo-Plasencia. Dig-ital elevation model from SGE (1997).
Fig. 1.- Principales fallas del Macizo Ibérico (MOPT, 1992). Las líneas rojas muestran las fallas potencialmente acti-vas: 1) Ventaniella, 2) Asturias central (Franja Movil In-termedia), 3) Asturias Occidental (Espina), 4) Borde Norte de la Cuenca del Duero, 5) Sabero-Gordón, 6) León, 7) Porma, 8) Bierzo, 9) Galicia Norte, 10) Galicia Sur, 11) Galicia Central, 12) Sarria , 13) Montforte, 14) Borde Sur del Sistema Central, 15) Borde Norte del Sistema Central, 16) Seisa-Lousa, 17) Sobreira-Formosa-Pomar-Grade, 18) Ponsul, 19) Nazaré-Pombal, 20) Sierra Albarrana, 21) Las Portillas, 22) Monte Chaõ, 23) Manteigas-Vilariça-Bara-gança, 24) Penacova-Regua-Verín, 25) Borde Norte de la Cuenca del Guadiana, 26) Béjar, 27) Vidigueira-Moura, 28) Grandola, 29) Río Sor-Montargil, 30) Tejo Inferior, 31) Alentejo-Plasencia. Modelo digital de elevaciones de SGE (1997).
88 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
(Fig. 4). The geometric relationship between the dike and the fault has also been redefined and shows that the dike and the fault are spatially separated by <2 km distance (Capote and Villamor, 1999). The dike did not intrude along the fault plane and the fault clearly displaces the dike (i.e., postdates it). These new interpretations of the history of the APF are relevant to active faulting stud-ies because they suggest that movement along the fault is relatively recent and that the fault may still be active.
Two phases of movement on the APF have been de-scribed (Villamor, 2002). The first phase started some-time after emplacement of the Jurassic dike to Early Mi-ocene, during the Eurasia-Iberia collision which created large basins associated with long-wavelength folding in the region (Capote et al., 2002). The APF has been inter-preted to have moved during this phase with a left-lateral movement displacing the large basins. The collision at the SE boundary of Iberia from Middle Miocene onwards restructured the region and produced a long wave length curvature in the fault facilitating the creation of pull-apart basins with further left-lateral movement along the fault. Deposition of Miocene sediments is associated to the for-mation of pull-apart basins. In some pull-apart basins, subsidence preserved the Eocene to early Miocene sedi-ments beneath the Middle Miocene and younger sedi-ments.
The first studies that considered the current activity of the APF were on the Portuguese sector of the fault (Pi-mentel and Azevedo, 1989; 1992; 1994; Brum da Silvei-ra, 1990; Cabral, 1995; Pimentel, 1997). Cabral (1995) described fault displacements that postdate late Pliocene sediments and geomorphic surfaces in the northernmost sector of the APF in Portugal, from Campomaior to Ervidel (Fig. 3). Tertiary sediments are preserved (main-ly on the SE side of the fault) at some locations, as a consequence of post late Pliocene vertical offsets of the order of 20-60 m. Post-Miocene push-up structures are described within this sector (Brum da Silveira, 1990). At some locations Early Quaternary sediments do not seem to be displaced by the fault (Cabral, 1995).
The APF in Portuguese territory is characterised by obvious recent displacements that led Cabral (1995) to suggest that the fault is more active in the southwest part of the fault. Pimentel and Azevedo (1992; 1994) and Pimentel (1997) established the role of the APF in the formation and evolution of the Sado Basin (Fig. 3) as a basin bounding fault. The Sado Basin formed during the Paleogene as a consequence of subsidence on the hang-ing wall of reverse faults oblique to the APF. The APF played a secondary role as a normal fault bounding the basin at this stage. During the last major restructuring of the basin (from 10 Ma to the present), subsidence of the
NE trending strike-slip faults are conspicuous in the Iberian Massif (the Variscan basement of the Iberian Pe-nisula) (Fig. 1). In Portugal, vertical displacement along those faults has been dated as Upper Miocene-Quaternary (Cabral, 1989; Carvalho et al., 2006). In the NW of the Iberian Massiff, NE trending faults are associated with active intraplate seismicity (González-Casado and Giner Robles, 2000; Rueda and Mezcua, 2001; López-Fern-ández et al., 2004; Martínez-Díaz et al., 2006). In this latter area, the drainage pattern has also been described as controlled by NE-SW faults (Martín-González, 2009). More recent paleoseismic studies have revealed the Qua-ternary activity of the Vilariça fault (NE trending fault; fault 23 on Fig 1), with at least two Mw>7 events in the last 14.5 ka with a slip rate of 0.3-0.5mm/yr (Rockwell et al., 2009).
2.1. Geological History of the APF
Based on the similarity of the APF with other NE trending faults of the central/western part of the Iberian Peninsula, several authors considered the APF to have formed during a dominant strike-slip regime at the end of the Variscan orogeny (Late Carboniferous to Permi-an; Parga Pondal, 1969; Arthaud and Matte, 1975). The NE trending faults in the region are associated with late Carboniferous to Permian sediments, and have different total displacements associated with different age granitic formations (co- and post- Variscian Orogeny batholiths).
The APF is associated with a Mesozoic dike along its entire length (Fig. 3). The presence of a large fault in as-sociation with a Mesozoic basic dike, the Messejana dike, was described as early as 1950s (Del Valle Lersundi, 1959; Quesada García, 1960; García de Figuerola, 1963; 1965; Parga Pondal, 1969; Arthaud and Matte, 1975; Ve-gas, 1974; 1975). The dike, dated as Jurassic, is associat-ed with the opening of the Atlantic Ocean (Ziegler, 1989; Stampfli and Borel, 2002). Because of the late Carbonif-erous to Permian age assigned to the APF in early studies, the dike was interpreted to have intruded along the fault (Arthaud and Matte, 1975).
Studies subsequent to Arthaud and Matte (1975) have mapped the Spanish part of the APF in detail, and sug-gested that the fault postdates the emplacement of the dike (i.e., post-Jurassic) and that its main period of movement is more likely to be Tertiary (Capote et al., 1996; Capote and Villamor, 1999; Villamor, 2002). No late Carbonifer-ous-Permian sediments and/or differential displacements on different aged granitic batholiths associated with the APF have been found (Villamor, 2002). Pull-apart basins along the APF are the result of left lateral movement of the fault and they contain Tertiary-Quaternary sediments
89Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
basin took place across the APF (Pimentel, 1997). Sedi-ments <1.5 Ma in age are displaced by the APF and two other sub-parallel faults. Along the southern sector of the fault onshore, post late Pliocene vertical displacement of the fault (up to 80 m) provide a Quaternary vertical slip rate of 0.04 to 0.05 mm/yr. Net displacements of 0.056 to 0.07 mm/yr were derived from vertical slip rate and slickenside orientations (Cabral, 1995).
3. Geometry and segmentation of the APF
Along its entire length, the APF is sub-parallel to the Messejana Dike. The fault is 500 km long onshore and possibly 100 km more offshore (Cabral, 1995). The fault-dike couplet forms a clear narrow trough in the landscape (Fig. 5). The APF structure in detail consists locally of one to several sub-parallel fault traces over a width of ≤ 2 km. In some areas, where there are several sub-parallel traces, it is difficult to discern the main fault traces from secondary traces.
The APF can be divided in three sectors, two in Spain and one in Portugal, based on its azimuth and broad ge-
ometry (Figs. 3 and 5). The Spanish sectors will be re-ferred to as northern and central, and the Portuguese sector as southern. The northern sector extends from the margin of the Duero Basin to the city of Plasencia (Fig. 3). The fault crosses the Spanish Central Mountain Sys-tem (SCMS in Fig. 5) and displays as a linear trace with a constant N55°E azimuth. In the central sector, from Plas-encia city to the border with Portugal, the fault crosses the Extremadura Meseta (EM in Fig. 5) and has a curved trace with an azimuth changing from N55°E at the north-ern end to N30°E at the south. The Portuguese sector is not described in detail in this study, but a general assess-ment of the 1: 1,000,000 map of the fault (ITGE, 1995) suggests that the fault has a sub-linear trace with an ap-proximate mean N45°E azimuth.
In detail the fault sectors can be divided into shorter segments. This segmentation is based on major lithology changes, the presence of pull-apart and push–up struc-tures, changes in the fault orientation, and the presence of one or more sub-parallel fault traces (Figs. 3 and 4). We consider this segmentation as the maximum possible segmentation associated with surface rupture of the APF
Fig. 2.- Seismicity of the Iberian Peninsula and location of the Alentejo-Plasencia fault. Note the lack of seismicity along the central and northern sector of the fault. Seismicity from IGN (Instituto Geográfico Nacional de España). Plate motions from DeMets et al. (1990; 1994).
Fig. 2.- Sismicidad de la Península Ibérica y localización de la falla de Alentejo-Plasencia. Nótese la ausencia de sismicidad a lo largo de los sectores central y septentrional de la falla. La sismicidad procede del IGN (Instituto Geográfico Nacional de España). Movimientos de pla-cas extraídos de DeMets et al. (1990; 1994)
90 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
in the absence of paleoseismic studies along the fault (see below).
The northern, central and southern sectors of the APF comprise three, four and six segments, respectively (Fig. 3). Only the central sector has been mapped with detail in this study and, thus, we consider its segmentation more robust than that of the other two sectors. We have used 1:1,000,000 and 1:50,000 geology maps and published studies (e.g.: Gonçalvez and Torre de Asunção, 1970; Gonçalvez et al., 1972; Cabral, 1995; ITGE, 1995) to de-fine the segments of the other two sectors. In this study we have not assessed segmentation of the offshore part of the fault.
The APF segments, from north to south (Fig 3) are:
3.1. Northern Sector
Muñana Segment (42 km long): extends from the Duero Basin margin to Casas del Puerto township. This segment is associated with the western margin of the Amblés Ba-sin. While the geomorphic expression shows a relatively linear trend (main azimuth of N58°E), and the dike is very continuous, the actual main fault trace is not clear on the geological maps.
Barco Segment (26 km): extends from Casas del Puerto to Barco de Ávila townships. There is a slight change in the fault trend (N56°E) compared to the segment to the north. The basement is homogeneous along its length and the fault is mapped as a single trace. The northern seg-ment boundary around Casas del Puerto is defined by a lithological change in the basement. Also at this location, the presence of Tertiary sediments could be locally asso-ciated with a step over of the main trace of the APF.
Jerte Segment (64 km): extends from Barco de Ávila to Plasencia pull-apart basin (Figs. 3 and 4). The fault has a N50°E trend, and a very linear trace forming a deeply incised linear valley (Jerte Valley) located in between two high relief area (Sierra de Gredos, SG, and Sierra Cande-lario, SC; Fig. 5). In the southern end of the segment, the Plasencia pull-apart basin is associated with a change in basement rocks (granitoids to the north and Precambrian slates to the south) (Figs. 3 and 4). This segment could also be divided at Puerto de Tornavacas (Fig. 3) where the geomorphic expression suggests the presence of sedi-ments associated with a left step. Further studies are re-quired to prove the presence of this step-over.
3.2. Central Sector
Cañaveral Segment (43 km): extends from the Plas-encia pull-apart basin to the Cañaveral pull-apart basin. As at the northern segment boundary, the southern end
of the pull-apart basin coincides with a change in base-ment lithologies, with Precambrian slates to the north and granitoids to the south. The fault is located adjacent to an elongated area of positive relief with same trend as the fault. The relief may arise from reverse movement of the Bejar fault (BF in Fig. 3), at the eastern margin of the Co-ria-Galisteo Basin (Figs. 3 and 4), a fault that is parallel to the APF along this whole segment and located 4-5 km west of the APF. It is possible that this fault may merge with the APF in depth. The APF comprises a single trace, except at the segment boundaries, and has a mean N50°E trend. The total lateral displacement of the fault along this segment is 3 km from displacements of the Silurian Quar-tize at Puerto de los Castaños area (Figs. 4 and 6).
Brozas Segment (27 km): extends between the Cañav-eral to the Ribera de Araya pull-apart basins. The Ribera de Araya pull-apart basin also coincides with a change from granitoids to the north to Precambrian slates to the south (Fig. 4). The APF comprises a single trace, except at the segment boundaries, and has a mean N50°E trend. The total displacement of the fault along this segment is 2.5 km from displacement of the boundaries of the Ca-beza de Araya Batholith (Fig. 4).
Aliseda Segment (34 km): extends from the Ribera de Araya to the Albarragena pull-apart basins. Again, the fault segment extends along uniform basement forma-tions of slates and quartzites and the boundary with gra-nitic batholites is located at the pull-apart basins (Fig. 4). The main fault azimuth is N30°E and the trace is very lin-ear. The total displacement of the fault along this segment is 1.5 km from displacements of the Silurian Quartize at Sierra de San Pedro area (Figs. 4 and 6).
Alburquerque Segment (20 km): extends from the Al-barragena pull-apart basins to the northern margin of the Guadiana Basin (Fig. 3). The fault trend and linear trace are very similar to the previous segment but the total dis-placement of the fault along this segment is 3 km from displacement of the boundaries of Alburquerque Batho-lith (Fig. 4). The fault azimuth is mainly N35°E (Fig. 4).
3.3. Southern Sector
Campomaior segment (22 km): extends from the north-ern margin of Guadiana Basin to a 4 km wide left step that lies just south of Caia River (CR in Fig. 3). Bedrock lithology along this segment consist mainly of meta-sed-imentary formations which are bounded to the north and south by granitoids. The main fault azimuth is N38°E. Total lateral displacement along the segment is of about 4 km at its midpoint and decreases northwards to 3 km and southwards to 1 km. Along this segment and the segment to the south, there is a significant vertical fault displace-
91Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
basin. Beringel segment (44 km): extends from the intersec-
tion with the Vidigueira–Moura Fault to Ervidel town-ship. Fault traces of this segment and the segment to the south form the southeastern boundary of the Sado Basin. This segment trends N43-50°E.
Odemira segment (75 km): extends from Odemira township to the coast. The fault has a trend of N45°E at the northern end which changes to a more southerly trend at the southern end (N15°E). The fault branches into sev-eral strands parallel to the coast. This segment is longer than others and it is possible that more detailed study would reveal the possibility of two or more segments in this area. Here, we present the simplest model.
ment component. Elvás segment (28 km): extends from the left step close
Caia River to Juromehna township. The fault azimuth is slighltly more easterly than the segment to the north (N38-40°E), particularly at its southern end.
Terena segment (33 km): extends from Juromehna to Falcoeiras. At the southern end the fault segment there is a left step where Tertiary sediments outcrop. This may indicate the presence of a pull-apart basin. The fault azi-muth is principally N48°E.
Portel segment (41 km): extends from the small sedi-mentary basin at the left step of Falcoeiras to the inter-section with the Vidigueira–Moura Fault, where the APF splays into two strands and forms a small sedimentary
Fig. 3.- General geological map along the Alentejo-Plasencia fault (ITGE, 1995) and segmentation model of the fault. APF, Alentejo-Plasen-cia Fault; BF, Bejar Fault; VMF, Vidigueira-Moura Fault; DB, Duero Basin; AB, Ambles Basin; CGB, Coria-Galisteo Basin; GB, Guadiana Basin; SB, Sado Basin; CR, Caia River.
Fig. 3.- Mapa geológico general a lo largo de la falla Alentejo-Plasencia (ITGE, 1995) y modelo de segmentación de la falla. APF, falla de Alentejo-Plasencia; BF, falla de Bejar; VMF, falla de Vidigueira-Moura. DB, cuenca del Duero, AB; cuenca de Ambles; CGB, cuenca de Coria-Galisteo; GB, cuenca del Guadiana; SB, cuenca de Sado. CR, río Caia.
92 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
al., 1990; Andeweg, 2002), whereas in southern Iberia the tectonic evolution may suggest a more recent start of the current tectonic regime. This late stage southern per-turbation is not clearly displayed in the study area. In the interior of the Iberian Peninsula, the sedimentary record and tectonic deformation also suggest no major chang-es since the onset of the collision of Iberia and Africa (Guadarrama Stage of Capote et al., 2002; see section 2). This suggests the changes in plate boundary stresses are largely attenuated by the time they are felt in the in-traplate region, and that the rates of deformation will be low but probably constant over long periods of time.
The current activity of the APF is evidenced by dis-placement of Tertiary-Quaternary sediments and by dis-placement of geomorphic surfaces formed within the current tectonic regime. In the next sections, we will describe in detail the field observations from the region studied (Cañaveral, Brozas, Aliseda and Alburquerque segments, corresponding to the Central Sector of the fault; Fig. 3) that illustrate the current tectonic active of the APF.
Fig. 4.- Location of the pull-apart basins and other points of interest along the Alentejo-Plasencia fault .Fig. 4.- Localización de las cuencas pull-apart y otros puntos de interés a lo largo de la falla Alentejo-Plasencia.
4. Evidence for current tectonic activity of the Alentejo-Plasencia fault
In this study, we define active faults as faults that have moved within the “current tectonic regime” (Muir-Wood and Mallard, 1992). The current tectonic regime is the period in which the tectonic stresses have remained con-stant (stress axis orientation and type of tectonic regime) and deformation can be assumed to be constant. Some authors described the beginning of the “Neotectonic pe-riod” for the Iberian Peninsula as the boundary between Middle and late Miocene (at 11-12 Ma) when the colli-sion with Africa was established (Baena et al., 1991). Other authors consider it starts at the end of the Pliocene (~ 2 Ma) when a NE trending contractional phase was established following a phase of tectonic quiescence as-sociated with E-W extension at the Gibraltar arc (Cabral, 1995).
For the central-western part of the Iberian Peninsula we accept that the current tectonic regime started during the Middle Miocene (Dewey et al., 1989; Srivastava et
93Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
pull-apart basin belong to the red Neogene series (fossils were dated early to middle Miocene; Hernández-Pacheco and Crusafont Pairo, 1960). A Plio-Quaternary alluvial fan sedimentary unit called Raña is also used here to as-sess timing of fault movement. This unit is described as the last stages of the ochre Neogene series by some au-thors, while others consider it a new sedimentary stage of early Quaternary age (see discussions in Cabral, 1995; Villamor, 2002 and references therein). Post-Raña sedi-ments are associated with alluvial fans and terraces. A de-tailed description of the sedimentary units in association with the APF in the study area, and correlation among basins is presented in Villamor (2002).
We consider that the sediments associated with the cur-rent tectonic regime in this region are Neogene sediments and younger, that is, sediments deposited since the red Neogene series. Therefore, deformation of those sedi-ments strongly suggests the faults of the APF have been active within the current tectonic regime.
The red and ochre Neogene series (hereafter called red and ochre series) along the APF are found within the pull-apart basins (Figs. 7 and 8). These sediments represent proximal alluvial fan deposits associated with the basin margin faults. In the Plasencia pull-apart basin (Fig. 7), for example, gravelly ochre sediments (with a strong weathering dominated by kaolinite) are found overlying clayey red sediments (where Early to Middle Miocene fossils were reported by Hernández-Pacheco and Crusa-font Pairo, 1960) at the eastern basin- bounding fault. Both series are sourced from Precambrian Slates round-ing the basin (Fig. 8a). The sediments are tilted back to-wards the fault indicating fault movement after deposi-tion (Fig. 8b).
In the Cañaveral pull-apart basin (Fig. 7), three distinc-tive types of sediments fill the basin. From top to bot-tom they are: gravel-dominated ochre series sediments sourced from Precambrian Slates rounding the basin; gravel-dominated red series sediments, also sourced from Precambrian Slates rounding the basin and separated from the overlying sediments by an angular unconformity; and sand-dominated Eocene-Oligocene sediments sourced from distant granitoides (Fig. 8e). The sedimentary facies displayed by these sediments suggest that while the Neo-gene series (red and ochre sediments) are proximal sedi-ments associated with movement of the boundary faults, the Eocene-Oligocene deposits were distal, pre-existing sediments that have been preserved by subsidence of the pull-apart basin. In the Cañaveral basin, the ochre se-ries are clearly faulted in a reverse fashion against the Eocene-Oligocene deposits along secondary faults at the northwest end of the basin (Fig. 8d), and in a normal fash-
4.1. Total displacement of the APF
The total displacement of the fault provides a minimum estimate of the slip rate in the current tectonic regime, and an indication of the horizontal to vertical displace-ment ratio. In the study area, the total lateral displace-ment of Precambrian to Silurian bedrock units ranges from 1.3 to 3.6 km if displacements are only derived from displacements along the main trace (Rincón et al., 2000; Villamor 2002) (Table 1). These measurements could be up to 6 km if drag folding in a width of at least 10 km is taken into the measurements (González Flores, 1996; see drag folding of Silurian Quartzite synclines in Figs. 4 and 6). For segments of the fault south of this study, the val-ues we obtain using regional geological mapping range from 3 to 3.5 km (Santos García and Casas Ruíz, 1982; Gonçalez and Torre Assunçao, 1970).
The horizontal to vertical displacement ratio was ob-tained from measuring lateral and vertical displacements of the Silurian Quartzite synclines at two locations, Puer-to de los Castaños and Sierra de San Pedro (Figs. 4 and 6; Table 1; for more detail see Villamor, 2002). The verti-cal values obtained are 80±20 m (Fig. 6) and 75±20 m, respectively. The preferred total horizontal displacements at these locations are 3.2±0.1 and 1.1±0.05 km, respec-tively. These are used to obtain horizontal to vertical dis-placement ratios of 40:1 and 15:1, respectively.
4.2. APF displacements of sediments deposited within the current tectonic regime (from Middle Miocene to present)
Tertiary formations in the study area are all terrigene-ous continental sediments. These sediments are trans-ported by alluvial fans in arid or semiarid conditions, as a response to tectonic uplift. Sediments associated with the APF are mainly related to the relief created at the edges of the pull-apart basins and sediment preservation is due to basin subsidence (Figs. 7 and 8a). In the wider area around the study area, fossil records have only been found at one location in the Plasencia pull-apart basin. There-fore, the ages assigned to the sediments in this study are based on published sedimentary correlations among the Ciudad Rodrigo (Martín-Serrano, 1991b), southwestern Duero (Santisteban et al., 1991), and the Plasencia pull-apart basin.
The main sedimentary sequences in the area are divided into the Paleogene (divided into Paleocene and Eocene-Oligocene Units) and Neogene sediments (divided into the Early-Middle Miocene series and the Middle-Upper Miocene series, also known as red and ochre Neogene series, respectively). The fossils found in the Plasencia
94 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
4.3. APF displacements of geomorphic surfaces formed within the current tectonic regime
We have used models of the evolution of the geomor-phic surfaces for the wider central and western Spain area (García-Abad and Martin-Serrano, 1980; Molina et al., 1985; Fernández Macarro and Blanco Sánchez, 1990; Martin-Serrano, 1991a; 1991b; 1994) to assign ages to the surfaces displaced by the APF in our study area. The model of geomorphic evolution for the central western Spain assigns ages to geomorphic surfaces based on presence of Tertiary and Quaternary sediments and properties of weathering mantles on bedrock associated with them. A detailed discussion of these models can be
ion against Precambrian slates along the western bound-ary fault. Also, at the eastern margin all three units are tilted back towards the eastern fault in a similar fashion to the sediments at the Plasencia pull-apart basin eastern margin. Along the eastern boundary fault of the Cañav-eral basin a Middle Pleistocene fluvial terrace is faulted (Fig. 8c).
Neogene series sediments are also found at Moro and Ribera de Araya pull-apart basins but the detailed rela-tionships with faulting are not exposed (Fig. 4). In the Al-barragena pull-apart basin (Fig. 4), deposits that are either Early Pleistocene (Villamor, 2002) or Neogene-Pliocene (age is from N. Pimentel pers. comm.), are clearly faulted (Fig. 8f).
Fig. 5.- Digital elevation mod-el (SGE, 1997) showing the geomorphic expression of the Alentejo-Plasencia fault (APF). The northern sector crosses the Central Ranges of Spain while the central and southern sector of the fault cross the Meseta. APF, Alentejo-Plasencia Fault; SCMS, Spanish Central Moun-tainous System; EM, Extrema-dura Meseta; SG , Sierra de Gre-dos; SC, Sierra de Candelario.
Fig. 5.- Modelo digital del terreno (SGE, 1997) mostrando la ex-pression geomorfológica de la falla Alentejo-Plasencia (APF). El sector norte cruza las sierras del Sistema Central Español mientras que los sectores central y meridional de la falla cruzan la Meseta. APF, falla Alentejo-Pla-sencia; SCMS, Sistema Central Español; EM, Meseta extremeña Meseta; SG , Sierra de Gredos; SC, Sierra de Candelario.
95Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
quartzite. There are two levels of Raña deposits. The up-per one, S- Raña 1 (S-R1 in Fig. 9a) lays conformably over a well-developed weathering mantle. This mantle is a smectite-rich mantle and becomes kaolinite-rich at the top suggesting superposition of the Middle to Upper Miocene weathering (coeval with depositions of the ka-olinite-rich ochre Neogene sedimentary series), over the early to middle Miocene weathering (coeval with deposi-tions of the smectite-rich red Neogene sedimentary se-ries). The lower Raña surface, S-Raña 2 (~ 50 m below the upper one), is erosional onto the weathering mantle.
Vertical displacements of the S-Bas surface are more obvious at the Plasencia, Moro and Cañaveral pull-apart basins (Fig. 9a) where the basin subsidence is large com-pared with vertical displacements along other sections of the fault. Analysis of the geomorphic surfaces combined with gravity modelling used to assess basin thickness suggest that the subsidence of the S-Bas surface at the pull-apart basins is of the order of 160 to 300 m (Fig. 9b; Villamor, 2002). These values can be converted to horizontal displacements if we use results from numeri-cal modelling studies where subsidence in pull-apart basins is related to the amount of total lateral displace-ment (Rodgers, 1980). That study suggests that subsid-ence represents 15 to 25% of lateral displacement. Thus, horizontal displacement on the fault of 0.8 to 2 km are
Fig. 6.- Total horizontal and vertical dis-placements of the Alentejo-Plasencia fault. Upper figure shows map view of the Silurian quartzite syncline (Puerto de los Castaños area) and possible total left lateral offsets. Lower figure shows a topographic profile along the northern flank of the syncline to assess vertical offset. Information was obtained for 1:50,000 maps (Martín Herrero, 1987b; Bascones Alvira and Martín Herre-ro,1987). For location see Figure 5.
Fig. 6.- Desplazamientos horizontal y vertical totales de la falla Alentejo-Pla-sencia. La figura superior muestra una visión en mapa del sinclinal de cuarci-ta del Silúrico (sector de Puerto de los Castaños) y posibles desplazamientos de desgarre lateral-izquierdo. La figura inferior muestra un perfil topográfico a lo largo del flanco norte del sinclinal con el fin de estimar el desplazamiento vertical. La información fue obtenida a partir de mapas 1:50,000 mapas (Martín Herrero et al., 1987b; Bascones-Alvira y Martín-Herrero,1987).Ver Figure 5 para localización.
found in Villamor (2002). A description of sediments and weathering mantles in this area is presented by Tsige et al. (1997). For the Quaternary surfaces we have used the ages assigned to terraces of different altitudes above the Tagus and Guadiana Rivers (Ugidos Meana et al., 1987a; 1987b; 1988;;Pérez-González et al., 1989).
Of the surfaces defined for the study area (Tsige et al., 1997; Villamor, 2002), the following are relevant to as-sess the current activity of the APF (Fig. 9):
S-Bas (superficie sobre basamento): is the extensive geomorphic surface in the Extremadura Meseta. This surface represents the exposed unweathered basement after the weathering mantle has been stripped. The exact age is difficult to assign and the surface is likely to be diachronous in age. However, clay mineralogy studies of the area close to the APF (Tsige et al., 1997) suggest that the oldest age of the weathering mantle is correlative to the red Neogene series (Early to Middle Miocene; with dominant smectitite over illite and kaolinite) of the Duero Basin (described above).
S-Raña (superficie sobre raña): is the paleo-ground sur-face above the Raña sediments. The Raña deposits have intense and characteristic weathering. Its fine grained components have been fully weathered to clays (illite and kaolinite) and the coarse grained are mainly, and almost exclusively, very rounded gravel (occasionally blocks) of
96 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
implied since formation of the pull-apart basins. Vertical displacements of the surface S-Raña of ~2m
has been found north of Ribera de Albarragena (location shown on Fig. 4). This value can be converted to horizon-tal displacement using the horizontal to vertical ratio esti-mated from displacement of older chronological markers (section 4.1; Table 1). The estimated horizontal displace-ment value associated with the S-Raña is 20 to 100 m if we use both ratios shown on Table 1.
5. Preliminary characterisation of the earthquake potential of the APF: fault slip rate, magnitude and recurrence interval
5.1. Fault slip rate of the APF
Fault slip rate estimates for the APF presented here are not well constrained, but are the best available. Most of the displacement measurements are from older reference
Fig. 7.- Geological maps of the Plasencia and Cañaveral pull-apart basins. Maps produced in this study at 1:25.000 scale from review of aerial photos and existing maps (Martín Herrero et al., 1987a; 1987b; Ugidos Meana et al. 1987), and field reconnaissance.
Fig. 7.- Mapas geológicos de las cuencas pull-apart de Plasencia y Cañaveral. Mapas generado sen éste estudio a escala 1:25.000 a partir de la revisión de fotografías aéreas, cartografías previas (Herrero et al., 1987a; 1987b; Ugidos-Meana et al. 1987), y reconocimientos de campo.
97Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
Fig. 8.- A) Photograph of the normal fault contact between basement and Tertiary sediments at the eastern border of the Plasencia pull-apart basin. B) Neogene sediments of the Plasencia pull-apart basin are tilted towards the eastern normal fault. C) Deformed Middle Pleistocene fluvial terrace on the eastern normal fault of the Cañaveral pull–apart basin. Displacement across fault is > 1m. D) Paleogene sedi-ments thrusted over Neogene sediments along a secondary reverse fault on the NW part of the Cañaveral pull-apart basin (Lo-cal road to Coria township). E) Paleogene to Neogene sedimentary sequence in the Cañaveral pull-apart basin. Neogene sedi-ments lay unconformably over Paleogene sediments. All sediments in the photograph are tilted towards the eastern margin fault of the basin. F) Fractured Early Pleistocene fluvial terrace. For locations of Figs. 8a to 8e, see Fig. 7. For location of Fig. 8f, see Fig. 5.
Fig. 8.- A) Fotografía del contacto por falla normal entre el basamento y los sedimen-tos terciarios en el borde este de la cuenca pull-apart de Plasencia. B) Los sedimentos neógenos de la cuenca pull-apart de Pla-sencia se encuentran basculados hacia la falla normal oriental. C) Terraza fluvial del Pleistoceno Medio deformada en la falla normal oriental de la cuenca pull-apart de Cañaveral. El desplazamiento en la falla es > 1m. D) Sedimentos paleógenos afec-tados dispuestos sobre sedimentos neóge-nos mediante una falla inversa secundaria en el sector NO de la cuenca pull-apart de Cañaveral. (carretera local a la ciudad de Coria). E) Secuencia sedimentaria paleó-gena a neógena en la cuenca pull-apart de Cañaveral. Los sedimentos neógenos se disponen discordantes sobre sedimentos paleógenos. Todos los sedimentos en la fotografía están basculados hacia la falla marginal oriental de la cuenca. F). Terra-za del Pleistoceno Inferior fracturada. Ver Fig. 7 para localización Figs. 8a a 8e. Para localización de Fig. 8f, ver Fig. 5.
horizons and the age associated with those displacements has large uncertainties. Recent (Quaternary) fault dis-placements are difficult to find along the APF and only vertical displacements could be measured. The trans-formations from vertical to net displacements (based on horizontal to vertical ratios obtained from total fault displacements or from other transformations described above) implemented here carry great uncertainties.
Slip rates have been obtained from three sources: the total displacements (e.g. Fig. 6), displacements since the initiation of pull-apart basins (e.g. Fig. 9), and the dis-
placements of the geomorphic surface associated with Raña deposits calculated above (Table 1). To obtain the slip rate associated with total displacements, we have used a range of ages for the initiation of movement along the APF. Fault initiation time is debatable but it has been suggested that it took place either during the Oligocene to Early Miocene (as early as 35 Ma ; Villamor, 2002) or coincident with the initiation of the pull-apart basin dur-ing Early to Middle Miocene (as early as 16 Ma ago; Vil-lamor et al., 2004). We obtain values of 0.03 to 0.2 mm/yr from these calculations (Table 1). These estimates are
98 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
as the Raña age. We consider that ages of 2 Ma may be more representative than 5 Ma for the end of the deposi-tion of the Raña deposits because, despite the diachronic character of the deposit, to date, the only age available age for the Raña is close to 2 Ma (~ 1.7 Ma; Baena and Díaz, 1997). We thus propose the ~0.01 mm/yr slip rate as a best-estimate lower slip rate for the fault.
Low to very low fault slip rates for the APF in the range from 0.001 to 0.1 mm/yr are supported by only rare ob-servations of recent geomorphic lateral offsets (typical of active strike-slip faults). From the aerial photo review and analysis of DEMs for the Cañaveral, Brozas, Aliseda y Alburquerque segments we could only identify a pos-sible recent fault scarp and a shutter ridge close to the Moro pull-apart basin (Fig. 10). Our results are also in agreement with slip rates obtained for the southern sector of the fault (0.056 to 0.07 mm/yr; Cabral, 1995).
5.2. Earthquake magnitudes associated with the APF
Earthquake magnitudes estimated for rupture of the APF range from Mw 6.6 to 8.7 (Fig. 11; Table 2; Appen-
preliminary and the assumption of constant slip rate may not be realistic in this intraplate setting. However, these values do provide a basis for considering earthquake haz-ard. The slip rate values do agree in general terms with the subtle geomorphic expression of current activity de-scribed above and are coherent with slip rates from other similar faults in the Iberian Massif (see below).
Our best estimates of slip rate of makers of recent age (within the current tectonic regime) are 0.01 to 0.1 mm/yr (simplified from values on Table 1). For the slip rate values associated with the initiation of the pull-apart ba-sins we use ~ 16 Ma years (pull-apart basin initiation; Villamor et al., 2004). Those values are 0.05 to 0.1 mm/yr (Table 1), which are also in agreement with slip rate values of 0.3-0.5 mm/yr in similar NE trending strike-slip faults in the Iberian Massif from paleoseismic studies (Rockwell et al., 2009). For slip rates associated with the S-Raña surface, we use a range of ages from 5 to 2 Ma for the Raña sediments (based on different authors, see discussion in Villamor, 2002 and section 4). For the S-Raña we obtain slip rate values from 0.004 to 0.05 mm/yr if we take into account values obtained using 5 and 2 Ma
Fig. 9.- A) Regional geological cross-sections north of Cañaveral pull-apart basin (see location on Figure 5; cross-section is based on Martín Herrero et al., 1987b). See text for description of geomorphic surfaces (S-Bas, S-R1and S-Q).B) Detail geological cross-section of the Cañaveral pull-apart basin see location on Figures 5 and 7).
Fig. 9.- A) Cortes geológicos regionales al norte de la Cuenca pull-apart de Cañaveral (ver localización en figura 5; el corte está basado en Martín-Herrero et al., 1987b). Ver texto para la descripción de las superficies geomorfológicas (S-Bas, S-R1and S-Q). B) Corte geológico de detalle de la Cuenca pull-apart de Cañaveral, ver localización en figuras 5 y 7).
99Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
dix 1). These magnitudes have been estimated using em-pirical scaling relationships of magnitude as a function of fault length and fault area (Wells and Coppersmith, 1994; Anderson et al., 1996; Berryman et al., 2001; and Stirling et al., 2002). Potential rupture length has been assigned from fault geometry and the fault has been divided into possible fault segments (Fig. 3; Table 2). This segmen-tation represents the smallest possible surface ruptures of the APF based on our mapping. These will produce magnitudes between Mw 6.6 and 7.6 (Table 2). Because we do not have appropriate paleoseismic data to confirm whether the fault always ruptures in small segments or in multiple segments, we have also assumed that it can rup-ture 2 segments or more, up to the whole fault, i.e., mi-nimum segmentation (Table 2). This assumption implies that the maximum magnitude associated with the APF, for a non-segmented rupture model of 500 km length, is Mw 8.7 (Fig. 11). The magnitude uncertainty depends on the scaling relationship used, but more importantly on the segmentation model chosen (Fig. 11).
5.3. Rupture recurrence interval associated with the APF
We have obtained recurrence times for possible surface rupture of the APF from the estimated Mw and slip rate.
We have used the relationship developed by Wesnousky (1986):
T= Mo/Mo rate (1)
where T is the recurrence interval, Mo is the seismic moment and Morate is the rate at which seismic moment is released. Mo and Mo rate are obtained from:
log Mo=16.05 + 1.5 Mw (Hanks and Kanamori, 1979)
and
Mo rate=μ A SR,
where μ is the crustal rigidity (3 x 1011 dynes/cm2), A is the fault area (we have used a seismogenic crustal depth of 20 km) and SR is the slip rate.
The recurrence intervals (RI) for rupture of the APF range from 10 ka to ~4 Ma depending on the segmentation model and the slip rate used (Table 2; Appendix 2). Mini-mum recurrence times (of the order of tens of thousands of years) are obtained for a maximum segmentation mod-el (i.e., shortest possible rupture lengths) and maximum slip rate. The maximum recurrence interval (of 4 Ma) is obtained for a whole fault rupture and minimum slip rate. Mw and recurrence intervals obtained here are very pre-liminary and have large uncertainties because they are not
Location Horizontal displacement (km)/vertical displacement (km) Slip rate (mm/yr) Horiz:
vert+
TotalAssociated
with pull-apart formation
Associated with Raña
surface
Total(for 35 Ma/
16Ma)
Associated with pull-apart
formation(16 Ma)
Associated with Raña
surface (for >5 Ma/ 2Ma)
Plasencia 3.30±0.35/-
1.20±0.40*/0.20±0.03
0.09±0.01/0.20±0.02H
0.07±0.02 N
Moro 3.30±0.35/-
1.20±0.40*/0.20±0.04
0.09±0.01/0.20±0.02 H
0.07±0.02 N
Puerto Castaños 3.2±0.10/0.08±0.02 -
0.09±0.002/0.20±0.01N 40:1
Cañaveral 2.2±0.10/-
1.5±0.50*/0.25±0.05
0.06±0.002/0.10±0.01
0.09±0.03 N
Cabeza Araya 2.40±0.25/- - 0.07±0.01/
0.10±0.01 H
Ribera Araya 1.60±0.45/- - 0.04±0.01/
0.10±0.003 N
Aliseda 1.10±0.05/0.075±0.02 - 0.03±0.002/
0.07±0.005 H 15:1
Ribera Albarragena
1.3±0.20/- - 0.06±0.04**/
0.002±0.0010.04±0.01/0.08±0.01 H
0.012±0.008 /0.03±0.02 N
* Derived from vertical displacement using Rodgers (1980); ** Derived from vertical displacement using mean results from horizontal to vertical ratios on last column; +Horizontal to vertical ratio; only calculated where both values are obtained independently; N Net slip rate; H Horizontal slip rate
Table 1.- Displacement and slip rate values associated with the APFTabla 1.- Desplacemiento and tasa de deslizamiento associados a la FAP
100 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
based on specific paleoseismic data and, thus, they should only be used as a first order approximation. With the cur-rent data, is very difficult to assess the best estimate RI for the APF. It is likely that ruptures will tend to be short (maximum segmentation model) because the fault is slow and has small total displacement (~ 3 km), and thus the fault plane is likely to have important asperities (Stirling et al., 1996). This can reduce the RI range to 20-30ka if we use the mean slip rate value (Table 2).
6. Contribution of the APF and other slow slip faults in the interior of Iberian Peninsula to seismic hazard
We have calculated the contribution of the APF and other slow slip faults to the seismic hazard of the interior of the Iberian Peninsula. Our aim is to assess whether the identi-fied fault structures pose a risk to society in this region. We have approached this assessment in two ways. Firstly, we assess the contribution to the probabilistic seismic hazard of a typical active fault representing the whole range of Mw and RI values of the area. This is a useful exercise to gain an understanding of the return period at which these faults may pose a hazard. Secondly, we produce probabi-listic hazard maps by accumulating the contribution of all active and potentially active faults in the region (note that we only focus on the contribution from fault sources not from background seismicity in this study) .
For our first assessment we use the dataset of possi-ble active fault sources (Figs. 1 and 12) that Villamor (2002) compiled for this region (Appendix 1). As men-tioned above, fault slip rates in the region are difficult to obtain because faults are slow moving and geomorphic expression is very subtle. Early studies of slip rate values
in Portugal (Cabral, 1995) pioneered active fault char-acterisation in the area. Recently (last ~ 10 years) active faults have been the focus of detailed studies and a few new slip rates have been obtained in the Iberian Peninsula (Villamor, 2002; Rockwell et al., 2009) and incorporated into hazard studies (e.g., Villamor, 2002). When slip rates have not been previously assessed, Villamor (2002) esti-mated them based on ages of displaced geological fea-tures, or assigned values of neighbouring faults of known slip rate when geomorphic similarities were present. We have updated that dataset and extracted information on the typical magnitude and slip rate values for faults in the area. These data sets are presented in Appendices 1 and 2. Because of the scarce information on fault activity in this area we have assigned large uncertainties to slip rate values. We have used Villamor (2002) fault segmentation models (Fig. 12 and Appendix 2) and the typical fault segment lengths and associated earthquake magnitudes evident in the region.
The compilation showed that while the rupture lengths (and associated Mw values) of the APF are representative of the range of values obtained for faults in the wider re-gion, the APF slip rate is within the lower range (Table 2; Appendix 2). Slip rates for faults in the interior of Iberia generally range from <0.01 to ~ 0.2 mm/year, although the Lower Tagus and Manteigas-Bragança faults could exceed 0.5 mm/year.
To explore the effects that the variation of Mw and slip rate could have on a site close to an active fault for faults in the intraplate of Iberia, we use the APF and its seg-mentation model with segments that range in length from 20 to 500 km in length (representative of whole range of segment lengths for potentially active faults in this study,
Fig. 10.- Recent fault scarps along the Alentejo-Plasencia Fault (IGN aerial photograph at 1:30.000 scale, 1985. Run H.M.N. 622, photo number 00012). Location of aerial photo shown in Fig. 5.
Fig. 10.- Escarpe de falla reciente a lo largo de la falla Alentejo-Plasencia (fotografía aérea del IGN a escala 1:30.000, 1985. Pasada H.M.N. 622, fotografía núme-ro 00012). La localización de la foto se muestra en la Fig. 5.
101Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
Fig. 11.- Mw estimates and segment lengths associated with active faults in the intraplate area of the Iberian Peninsula. Fault scaling relationships are: Wells and Coppersmith, 1994; Anderson et al., 1996; Stirling et al., 2002; and Berryman et al., 2001.
Fig. 11.- Magnitudes Mw estimadas y longitudes de segmentos asociadas con las fallas activas en el área intraplaca de la península Ibérica. La relaciones de escala son: Wells and Coppersmith, 1994; Anderson et al., 1996; Stirling et al., 2002; and Berryman et al., 2001.
Appendix 2), with slip rate values of 0.01, 0.1 and 0.5 mm/year (whole range of values for potentially active faults in this study, Appendix 2) . Several hazard curves are developed for a site at Plasencia township, located within 1 km of the fault trace (Fig. 12 and 13). In this evaluation the only seismic sources are the different seg-ments and segmentation options of the APF. The curves represent combinations of different segmentation models (i.e., different segment lengths and thus different possible earthquake magnitudes) and different possible slip rates on faults in the intraplate area of Iberia (Fig. 13).The seis-mic hazard assessment method uses procedures devel-oped in Stirling et al. (2012) and Villamor (2002) which are based on the algorithms of Cornell (1968). We have used Atkinson y Boore (1995) attenuation relationship.
The hazard curves in Figure 13 show a great variability depending of the segmentation model and the slip rate value of choice. We consider a Peak Ground Accelera-tion (PGA) value of 0.3g as the onset of significant dam-age even for structures with specific earthquake resilient. Faults with slip rate values of 0.01 mm/yr and large seg-ments (e.g., 1 segment of 500 km; see APF parameters in Appendix 2) have no contribution to 0.03g ground mo-tions. Faults with 0,01 mm/yr and maximum segmenta-tion rate (13 segments with segment lengths ranging from 22 to 63 km; see APF parameters in Appendix 2), only contribute to 0.3g ground motions for return periods ≥ 1Ma. Faults with 0.1 mm/yr slip rate and any segmenta-tion model, have an annual probability of exceedance of 0.3g PGA≥0.0008 (that is for a return period ≥ 80,000
102 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
years). Faults with slip rates of 0.5mm/yr have return pe-riods of 60,000 to 10,000 years for minimum to maxi-mum segmentation models, respectively.
Our second approach to assess the contribution of active faults to seismic hazard in intraplate Iberia is to produce a probabilistic peak ground acceleration map incorporating the contribution of all modelled faults in the region (Fig. 14). We consider that our best estimate source model is that with mean fault slip rate and maxi-mum segmentation (e.g.: for APF it would be 0.05 mm/yr and 13 segments; for the Manteigas-Bragança fault is 0.04 mm/yr and 5 segments; and so on; see Appendix 2 for all fault parameters). In such a low-strain area where faults have a small total displacement (e.g., APF has ~
3km), faults are likely to have large and/or numerous asperities (Stirling et al., 1996) and thus faults are more likely to rupture in small segments. While for most of the study area PGA is 0.2g for a 10,000 year return pe-riod, some areas show larger values (Fig. 14). For exam-ple, we obtain a PGA value of > 0.3 g in areas close to the fastest faults (≥ 0.5 mm/yr: Tejo Inferior and Vilariça faults) (Figs. 12a and 14). Also in areas surrounded by several faults PGA > 0.2 g are estimated (e.g. northern sector of the map in Fig 14).
Segmentation model Segment name Length
(km) SRMw
W & C (RA)1
MwAnderson1
(TD media)
MwStirling
pos 19001
MwBerryman1
RI (years)(Slip Rate min,
W&C(RA))
RI (years) (Slip Rate mean,
W&C(RA))
RI (years)(Slip Rate max,
W&C(RA))
Minimum(1 segment) All 500 0,1-0,01 7.99 8.51 8.02 8.65 40540 81079 405395
Maximum(13 segments)
AP1-Muñico 41,88 0,1-0,01 6.93 7.26 7.17 7.21 12639 25278 126388AP2 -Barco 25,73 0,1-0,01 6.73 7.02 7.00 6.93 10052 20105 100524AP3 -Jerte 63,7 0,1-0,01 7.11 7.47 7.32 7.45 15392 30785 153925
AP4 -Cañave 43,15 0,1-0,01 6.95 7.28 7.18 7.23 12818 25635 128175AP5-Brozas 26,8 0,1-0,01 6.74 7.04 7.02 6.95 10247 20494 102468AP6-Aliseda 34,13 0,1-0,01 6.85 7.16 7.10 7.09 11480 22960 114799AP7-Alburq 20,87 0,1-0,01 6.64 6.91 6.93 6.81 9110 18221 91104AP8 -Campo 22,31 0,1-0,01 6.67 6.94 6.96 6.85 9401 18801 94006
AP9 28,02 0,1-0,01 6.76 7.06 7.03 6.98 10463 20927 104634AP10 32,82 0,1-0,01 6.83 7.14 7.09 7.07 11271 22541 112706AP11 41,13 0,1-0,01 6.93 7.25 7.17 7.20 12532 25064 125319AP12 44 0,1-0,01 6.96 7.29 7.19 7.24 12936 25871 129356AP13 75 0,1-0,01 7.18 7.56 7.37 7.55 16620 33241 166204
7 segments(6 segments +
AP13)
AP2,1 68.0 0,1-0,01 7.14 7.51 7.34 7.49 15872 31745 158724AP4,3 107.0 0,1-0,01 7.33 7.73 7.49 7.75 19641 39283 196414AP5,6 61.0 0,1-0,01 7.09 7.45 7.30 7.43 15082 30165 150823AP8,7 43.0 0,1-0,01 6.95 7.28 7.18 7.23 12797 25593 127966AP10,9 61.0 0,1-0,01 7.09 7.45 7.30 7.43 15082 30165 150823AP11,12 85.0 0,1-0,01 7.24 7.62 7.41 7.62 17627 35255 176275
5 segments(4 segments +
AP13)
AP3,2,1 131.0 0,1-0,01 7.42 7.84 7.56 7.87 21601 43203 216013AP6,5,4 104.0 0,1-0,01 7.32 7.72 7.48 7.74 19381 38761 193807AP9,8,7 71.0 0,1-0,01 7.16 7.53 7.35 7.52 16198 32395 161977
AP12,11,10 118.0 0,1-0,01 7.38 7.78 7.53 7.81 20566 41132 205659
4 segments(3 segments +
AP13)
AP4,3,2,1 174.5 0,1-0,01 7.54 7.98 7.66 8.04 24718 49435 247176AP8,7,6,5 104.0 0,1-0,01 7.32 7.72 7.48 7.74 19381 38761 193807
AP12,11,10,9 146.0 0,1-0,01 7.47 7.89 7.60 7.93 22730 45461 227305
3 segmentsAP5,4,3,2,1 201.0 0,1-0,01 7.60 8.05 7.71 8.12 26416 52832 264159AP10,9,8,7,6 138.0 0,1-0,01 7.44 7.86 7.58 7.90 22136 44273 221364AP13,12,11 160.0 0,1-0,01 7.51 7.94 7.63 7.99 23730 47460 237301
2 segmentsAP6,5,4,3,2,1 235.0 0,1-0,01 7.67 8.13 7.76 8.21 28429 56858 284292
AP13,12,11,10,9,8,7 265.0 0,1-0,01 7.72 8.19 7.80 8.28 30081 60161 3008071Moment magnitude from scaling relationships: W&C (RA) = Wells and Coppersmith (1994): Mw=4.07+0.98logA; Anderson = Anderson et al. 1996): Mw=5.12+1.16logL-0.2logSR; Stirling (pos 1900) = Stirling et al. (2002): Mw=5.89+0.79logL; Berryman = Berryman et al. (2001): Mw=4.18+2/3logW+4/3logL
Table 2.- Seismic parameters of the APF (SR: slip rate; MW: moment magnitude; RI: recurrence interval)Tabla 2.- Parámetros sísmicos de la FAP (SR: tasa de deslizamiento; MW: magnitud de movimiento; RI: intervalo de recurrencia)
103Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
Active faults the intraplate of Iberia do not contribute significantly to seismic hazard at short return periods. However, they can be important contributors to hazard at critical facilities where return periods of interest may be 10,000 years or more. In figure 13 we show that if we choose, for example, a PGA value of 0.3 g as the thresh-old for earthquake shaking damage, then faults with a slip rate of ~0.1 mm/year may pose a threat to critical facilities, such as nuclear power plants or nuclear waste repositories (usually designed for a probability of exceed-ance of ~ 0.00001 per annum, or return period of 100,000 years). Faults with slip rate values of the order of 0.5 mm/yr, can exceed the 0.3 pga for the 10,000 year return pe-riod (0.0001 probability of exceedance of 0.3g) which is pertinent for high hazard dams and emergency response
7. Discussion
Slip rate values from intraplate faults in the interior of Iberia are in the range from 0.01 to 0.8 mm/yr (with best mean estimates for all faults ranging from 0.01 to 0.5 mm/yr). Magnitudes derived from possible rupture lengths range from Mw 6.6 to 8.7 depending on the choice of segmentation model and the fault scaling relationship, with estimates of Mw 6.6 to 7.6 from our preferred maxi-mum segmentation model. Derived rupture recurrence intervals range from 1200 years to ~ 4 Ma depending on the slip rate and magnitude assigned to the fault. The large range in values for the different fault parameters is a reflection of how difficult it is to characterise faults in intraplate regions.
Fig. 12.- A) Map of possible active fault sources in the intraplate area of the Iberian Peninsula. Filled cir-cles are sites where probabilistic hard assessments were undertaken. Fault names can be found in Ap-pendix 2. Numbers indicate modelled fault segments for each fault. B) Vector sum of slip rate values of active faults in the intraplate area of Iberia. Profiles are developed along three lines (I, II and III) that are parallel to the maximum horizontal shortening direc-tion (red lines; Herráiz et al., 2000). Black arrows are horizontal slip rate vectors for each fault crossed on each profile, and grey arrows are the summation of those individual fault vectors. Red arrows, and numbers, are the component of the vector sum that is parallel to maximum horizontal shortening direc-tion.
Fig. 12.- A) Mapa de posibles falla como fuentes sis-mogenéticas en la región intraplaca de la península Ibérica. Los círculos sólidos son los lugares donde se llevó a cabo el cálculo de peligrosidad sísmica. Los nombres de las fallas se pueden encontrar en el anexo 2. Los números indican los segmentos modelizados para cada falla. B) Vector suma de los valores de velocidad de deslizamiento de las fallas activas en la región intraplaca de Iberia. Los perfiles se han calculado a lo largo de tres líneas (I, II and III) paralelas a la dirección de máximo acortamien-to horizontal (líneas rojas; Herráiz et al., 2000). Las flechas negras representan los vectores de velocidad de deslizamiento para cada falla cruzada en el perfil, y las flechas grises muestran la suma de todos los vectores individuales de las fallas. Las flechas rojas, y los números, muestran las componentes del vec-tor suma paralelas a la dirección de máximo acorta-miento horizontal.
104 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
Peak ground acceleration (g) for a 100 year return period
Fig. 14.- Contribution of all fault sources to probabilistic seismic hazard of central and western Iberia for a 10,000 year return period. Note that seismic hazard values do not include contribution from background seismicity.
Fig. 14.- Contribución de todas las fallas como fuentes sismogenéticas a la peligrosidad sísmica probabilista en la zona central y oriental de Iberia para un periodo de retorno 10000 años. Nótese que los valores de peligrosidad sísmica no incluyen la contribución de la sismicidad de fondo.
Fig. 13.- Seismic hazard curves for a generic fault in the intra-plate area of Iberian Peninsula. Note that we have used the segmentation model of the Alentejo-Plasencia fault because it suggests fault segments that range in length from 20 - 60 km (fault divided into 13 segments) to 500 km (fault has only 1 segment). Calculations were undertaken for a site at Plasencia township.
Fig. 13.- Curvas de peligrosidad sísmica para una falla genérica en la región intraplaca de la península Ibérica. Nótese que se ha utilizado el modelo de segmentación de falla Alentejo-Pla-sencia porque sugiere segmentos con longitudes que varían de 20-60 km (para el caso de considerar la falla dividida en 13 segmentos) a 500 km (considerando la falla como un solo seg-mento). Los calculus fueron realizado para un emplazamiento situado en la ciudad de Plasencia.
105Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
gion of Iberia has significant implications for the seismic hazard of the Iberian Peninsula, the development of ap-propriate codes for different building and infrastructure types, and decisions on land use planning.
8. Conclusions
The APF is one of the active faults of the interior of the Iberian Peninsula. We consider that a fault is active if it has moved within the current tectonic regime and that the tectonic regime has not changed since the Neogene in the interior of Iberia. The APF displays clear deformation of geomorphic surfaces and sediments of Neogene and younger age.
We have characterised the earthquake potential of the APF. We have estimated the slip rate of the fault from dis-placements of geological formations and geomorphic sur-faces. APF slip rate ranges from 0.01 to 0.1 mm/yr with a best estimate of 0.05 mm/yr. We have also segmented the fault based on geometric features and obtained different segmentation models: a maximum segmentation model (shortest segments) with segments lengths ranging from 20 to 75 km; and minimum segmentation model of one segment of 500 km in length. We have assigned earth-quake magnitudes to fault rupture using international em-pirical relationships that use fault length and obtained Mw values from 6.6 to 8.7. Those parameters have been used to assess possible recurrence intervals for fault rupture with values ranging from 10 ka to 4 Ma. Our preferred model of maximum segmentation (i.e. shortest segments) and mean slip rate achieved Mw values of 6.6 to 7.6 and recurrence intervals of 20 to 30 ka.
A compilation of active fault parameters in the area shows that the Mw range estimated for the APF is repre-sentative of the whole area. However, the APF slip rate is in the lower part of the range for all active faults in the area with maximum values of 0.5-0.8 mm/yr.
We have calculated hazard curves including contribu-tions from all fault sources and we conclude that active faults of the intraplate Iberia do not contribute signifi-cantly to seismic hazard at short return periods typical of the building codes (~ 500 year return periods). However, they can be important contributors to hazard at critical facilities (high hazard dams, nuclear power plants, emer-gency response buildings) where return periods of inter-est may be 10,000 years or more. Our fault source char-acterisation is very preliminary (with large uncertainties) and further detailed studies of active faults across the whole plate boundary are required to confirm the values for the intraplate faults presented here.
facilities. For return periods of 475 years (probability of exceedence of 10% in 50 years), typical for the design of residential buildings, active faults in the intraplate of the Iberian Peninsula with slip rates of ≤0.5 mm/yr do not contribute to the hazard.
The combined contribution of several faults to the seismic hazard at a site is illustrated in figure 14, which represents the seismic hazard of our preferred model (mean slip rate and maximum segmentation model). The maximum expected PGA for a return period of 10,000 years occurs close to faults with ~ 0.5 mm/yr slip rate but particularly in proximity to several faults (i.e., such as areas with values > 0.25 PGA in the central part of fig-ure 14). The combined effect of several faults is also evi-dent when comparing the results for Plasencia and Coria towns. While both are located close to faults with similar low slip rate, the higher PGA of Coria is attributed to the contribution of several nearby faults (Fig. 14). This effect is also observed at the intersection of the APF and the North Guadiana Fault.
This sensitivity analysis raises the question as to wheth-er there is merit in studying low slip rate (<0.01 mm/yr) faults in the western and central Iberian Peninsula if they do not pose a risk to the society (except for nearby nu-clear power plants and other critical facilities). There are two main reasons why we should. Firstly, the confidence in the preliminary slip rate values presented here is low. Specific paleoseismic studies that provide confident as-sessments of slip rate have only been developed on a few faults. Current estimates of fault slip rates of 0.1 mm/yr used in this study present such high uncertainties that they could be easily re-evaluated to ≥0.5 mm/yr in fu-ture site specific projects. Secondly, only if we gain a full understanding of the way that deformation is distributed across the whole Iberian Peninsula, and how that total de-formation budget is absorbed, can we be sure that the slip rate values assigned to each fault are in the correct range.
A first attempt to assess whether the fault slip rate rang-es estimated here are reasonable is shown on figure 12b. In this figure, we add the deformation as described by fault slip rates across the intraplate area of the Iberian Peninsula. We sum the component of the slip rate in the direction of the maximum horizontal shortening axis of the stress tensor (Herráiz et al., 2000) in several transects. This indicates that, consistently across several transects, at least 0.2 to 0.4 mm/yr (approximately 5 to 10 % of the total plate boundary relative motion), may occur within intraplate Iberia. Improvement on this assessment could be achieved by assessing the whole plate boundary defor-mation budget in a consistent way, and by including other deformation measurements, such as GPS velocities. The partitioning of plate boundary strain into the intraplate re-
106 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
nental neogene synthesis and paleoclimatic interpretation. Rev. Soc. Geol. España 6(3-4), 29-39.
Capote, R., Muñoz, J.A., Simón, J.L., Liesa, C.L., Arlegui, L.E. (2002): Alpine tectonics I: the Alpine system north of the Betic Cor-dillera. In: Gibbons, W., Moreno, T. (ed.), The Geology of Spain. Geological Society, London: 367-400.
Capote, R., Villamor, P., Tsige, M. (1996): Tectónica alpina de la falla de Alentejo-Plasencia Fault, Macizo Hespérico. Geogaceta 7 (4), 917-920.
Capote, R., Villamor, P. (1999): La falla de Alentejo-Plasencia, un desgarre cortical de la colisión Alpina. In: Libro Homenaje a J. Ramirez del Pozo. Asoc. Geol. Geofis. Petrol. España: 151-158.
Carvalho, J., Cabral, J., Gonçalves, R., Torres, L., Mendes-Victor, L. (2006): Geophysical methods applied to fault characterization and earthquake potential assessment in the Lower Tagus Valley, Portu-gal. Tectonophysics 418, 277-297. doi:10.1016/j.tecto.2006.02.010
Cornell, C.A. (1968): Engineering seismic risk analysis. Bull. Seis. Soc. America 58(5): 1533-1606.
Crone, A.J., Machette, M.N., Bowman, J.R. (1992): Geologic investi-gations of the 1988 Tennant Creek, Australia, earthquakes; implica-tions for paleoseismicity in stable continental regions, U.S. Geolo-gical Survey Bulletin B 2032-A, A1-A51.
De Vicente, G., González-Casado, J.M., Muñoz-Martín, A., Giner, J., Rodríguez-Pascua, M.A. (1996): Structure and Tertiary evolution of the Madrid Basin. In: P.F. Friend, C.J. Dabrio (ed.), Tertiary Ba-sins of Spain. Cambridge University Press, Cambridge, New York: 263-267.
De Vicente, G., Vegas, R., Guimerá, J., Muñoz, A., Casas, A., Mar-tín Velazquez, S., Heredia, N., Rodríguez-Fernández, R., González Casado, J.M., Cloetingh, S., Andeweg, B., Alvarez, J., Olaiz, A. (2004): Evolución geodinámica y cenozoica de la placa ibérica y su registro en el antepaís. In: Vera, J.A. (ed.), Geología de España. S.G.E.-I.G.M.E., Madrid: 597-602.
De Vicente, G., Cloetingh, S., Van Wees, J.D., Cunha, P.P. (2011): Tectonic classification of Cenozoic Iberian foreland basins. Tecto-nophysics 502, 38-61. doi:10.1016/j.tecto.2011.02.007.
Dias, R.P., Cabral, J. (1991): Neogene and Quaternary reactivation of the Ponsul River fault (Central Portugal). Pub. IGN Ser. Mon. 8, 269-282.
DeMets, C., Gordon, R.G., Argus, D.F., Stein, S. (1990): Current plate motions. Geophys. J. Int. 101, 425-478. doi: 10.1111/j.1365-246X.1990.tb06579.x.
DeMets, C., Gordon, R.G., Argus, D.F., Stein, R. (1994): Effect of recent revisions to the geomagnetic reversal time scale on estima-tes of current plate motions. Geophys. Res. Lett, 21, 2191-2194. doi:10.1029/94GL02118.
Dewey, J. F., Helman, M. L., Turco, E., Hutton, D. H. W., Knott S. D. (1989): Kinematics of the western Mediterranean. In: M. P. Coward, D. Dietrich,, R.G. Park (ed.), Alpine tectonics. Geological Society Special Publications, London, 45, 265-283. doi:10.1144/GSL.SP.1989.045.01.15.
Del Valle Lersundi, J. (1959): Breve nota sobre la existencia de una importante falla en el SW de nuestra Península. Not. Com. Inst. Geol. y Min., 82 (3-4), 346-350.
Eurocode 8 (2006): Design of structures for earthquake resistance. British-Adopted European Standard, UK.
Fernández Macarro, B., Blanco Sánchez, J.A. (1990): Evolución Mor-fológica de la Depresión de Talavan-Torrejón El Rubio, Cáceres. I Reunión Nacional de Geomorfología, Teruel: 753-762.
Fonseca, J., Bossi, V., Vilanova , S. Meghraoui, M. (2000): Investi-gations unveil Holocene thrusting for onshore Portugal. EOS 81, 412-413.
García Abad, F., Martín Serrano, A. (1980): Precisiones sobre la génesis y cronología de los relieves apalachianos del Macizo Hespérico (Me-
Acknowledgements
We thank Luis I. González de Vallejo for financial sup-port and comments on early versions of this study. We also thank Tatiana Goded and Kate Clark for reviewing an early draft of the manuscript, and Rosa Tejero and Julian García-Mayordomo for journal reviews. Monica Cabeza, Elena Villamor, Michelle Park and Angel Vírseda helped with production of figures, tables and appendices. This study was jointly funded by Universidad Complutense de Madrid (Spain), ENRESA S.A. (Spain) and GNS Science (New Zealand).
References
Alonso J.L., Pulgar, J.A., García-Ramos, J.C., Barba, P. (1996): Ter-tiary basins and Alpine Tectonics in the Cantrabian Mountains (NW Spain). In: P.F. Friend, C.J. Dabrio (ed.), Tertiary Basins of Spain. World and regional geology series (6). Cambridge University Press, Cambridge, New York: 214-227.
Anderson, J.G., Wesnousky, S.G., Stirling, M.W. (1996): Earthquake size as a function of fault slip rate. Bull. Seis. Soc. America 86, 683-690.
Anderweg, B. (2002): Cenozoic tectonic evolution of the Iberian Pe-ninsula, causes and effects of changing the stress field. PhD Thesis. Vrie University, Amsterdam (The Netherlands): 178 p.
Arthaud, F., Matte, P. (1975): Les décrochements tardi-hercyniens du sud-ouest de l`Europe. Geometyrie et essai de reconstitution des conditions de la déformation. Tectonophysics, 25: 139-171. doi:10.1016/0040-1951(75)90014-1
Atkinson, G.M., Boore, D.M. (1995): New Ground–Motion Relations for Eastern North America. Bull. Seis. Soc. America 85(1), 17-30.
Baena, J., Bardaji, T., Goy, J.L., Silva, P.G., Somoza, L., Zazo, C. (1991): An attempt of fault activity data file and map modellization. Bull. INQUA Neotectonics Comm. 16, 48-54.
Baena, R., Díaz, F. (1997): Resultados paleomagnéticos de la raña del Hespérico Meridional (Montoro, Córdoba). Geogaceta 21, 31-34.
Bascones-Alvira, L., Martín-Herrero, D. (1987): Hoja geológica 622 (Torrejoncillo). Mapa Geológico de España E. 1:50.000.Segunda serie, I.G.M.E., Madrid.
Berryman, K.R.; Webb, T.H.; Hill, N.; Stirling, M.W.; Rhoades, D.A.; Beavan, R.J.; Darby, D.J. (2001): Seismic loads on dams Waitaki System, earthquake source characterisation. Institute of Geological and Nuclear Sciences client report 2001/129, New Zealand: 79 p.
Brum da Silveira, A. (1990): Neotectónica e Sismotectónica da Re-gião Vidigueira-Moura. MSc Thesis. Univ. Lisboa, Portugal: 204 p.
Brum da Silveira, A., Cabral, J., Perea, H., Ribeiro, A. (2009): Evi-dence for coupled reverse and normal active faulting in W Ibéria. The Vidigueira-Moura and Alqueva faults (SE Portugal). Tectono-physics 474, 184–199.
Cabral, J. (1989): An example of intraplate neotectonic activity, Vila-riça basin, Northeast Portugal. Tectonics 8, 285-303. doi:10.1016/j.tecto.2009.04.013.
Cabral, J. (1995): Neotectonica em Portugal Continental. Memor. do Int. Geol. e Min. 31, 263 p.
Calvo, J.P., Daams, R., Morales, J., López-Martínez, N., Agusti, j., Anadon, P., Armenteros, I., Cabrera, L., Civis, J., Corrochano, A., Díaz-Molina, M., Elizaga, E., Hoyos, M., Martín-Suarez, E., Martí-nez, J., Miossent, E., Muñoz, A., Pérez-García, A., Pérez-González, A., Portero, J.M., Robles, F., Santisteban, C., Torres, T., Van der Meulen, A.J., Vera, J.A., Pein, P. (1993): Up-to-date Spanish conti-
107Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
Martín-Serrano, A. (1991a): La definición y el encajamiento de la red fluvial actual sobre el Macizo Hespérico en el marco de su geodiná-mica alpina. Rev. Soc. Geol. España 4, 338-351.
Martín-Serrano, A. (1991b): El relieve del Macizo Hespérico y sus sedimentos asociados. En Alteraciones y paleoalteraciones en la morfología del oeste peninsular. Zócalo y cuencas terciarias. Mo-nografía nº 6. I.G.M.E.-S.G.E., Madrid: 9-26.
Martín-Serrano, A. (1994): El relieve del Mazizo Hespérico: Génesis y cronología de los principales elementos morfológicos. Cuaderno Lab. Xeolóxico de Laxe 19, 37-55.
Martín-Serrano, A., Santisteban, J.I., Mediavilla, R. (1996): In: P.F. Friend, C.J. Dabrio (ed.), Tertiary Basins of Spain. World and re-gional geology series (6). Cambridge University Press, Cambridge, New York: 255-261.
Martínez J.M Solares, J. Mezcua (2002): Catalogo sísmico de la Península Ibérica (800aC-1900). I.G.N. monografía 18, Madrid: 253 p.
Martínez-Díaz, J.J., Capote, R., Tsige, M., Villamor, P., Martín-González, F., Insua-Arévalo, J .M. (2006): Seismic triggering in a stable continental area: The Lugo 1995-1997 seismic sequences (NW Spain). Journal of Geodynamics 41, 440-449. doi:10.1016/j.jog.2006.01.001.
Molina, E., Blanco, J.A., Pellitero, E., Cantano, M., Jorda, J. (1985): Esquema sobre la evolución del relieve del Mazizo Hespérico en su sector Castellano–Extremeño. Stvdia Geológica Salmaticensia XX, 115-126.
MOPT (1992): Análisis sismotectónico de la Península Ibérica, Ba-leares y Canarias. M.O.P.T. Pub Tec. 26, Madrid.
Moreno Serrano, F. (1990): Superficies de erosión y fracturas en el enla-ce entre la Meseta Norte y la llanura extremeña (Salamanca-Cáceres). I Reunión de Geomorfología. Teruel: 39-49.
Muñoz-Martín, A., De Vicente, G. (1998): Origen y relación entre las deformaciones y esfuerzos alpinos dela zona centro-oriental de la Pe-nínsula Ibérica. Rev. Soc. Geol. España 11(1-2), 57-70.
Muir Wood R., Mallard, D.J. (1992): When is a fault extinct? J. Geol. Soc of London 149, 251-255. doi:10.1144/gsjgs.149.2.0251.
NCSE02 (2002): Real Decreto 997/2002, de 27 de septiembre, por el que se aprueba la norma de construcción sismorresistente: parte general y edificación (NCSR-02). Boletín Oficial del Estado, Octo-ber 11th, nº. 244, 35898-35967.
Nozal, F., Gracia , F.J. (1990): El piedemonte de la Sierra del Brezo (Montes Palentinos). Reunión Nacional. de Geomorfología, Teruel: 763-772.
Parga Pondal. J.R. (1969): Sistemas de fracturas tardihercínicas del Macizo Hespérico. Trabajos del Laboratorio Xeológico de Laxe 37, 1-15.
Pérez González, A., Cabra P., Ancoechea, E. (1989): Depresión del Tajo. Mapa del Cuaternario de España E 1:1.000.000, Memoria. I.T.G.E, Madrid: 175-186.
Pimentel, N.L. (1997): In: J. P. Calvo, J. Morales (ed.), A bacia terci-ária do Sado (SW Ibérico)- Síntese evolutiva e factores de controlo. Avances en el conocimiento del Terciario Ibérico. CSIC, Madrid: 217-220.
Pimentel, N., Azevedo, T. (1989): Evolução Plio-Quaternaria da serra de Grândola. Revis. Geoc. Do MNHN: 17-19.
Pimentel, N., Azevedo, T. (1992): Sobre la evolução do relevo e sedi-mentação quaternária no Baixo-Alentejo (Alvalade-Panóias). Gaia 4, 21-24.
Pimentel, N., Azevedo, T. (1994): Etapas e controlo alpino da sedi-mentação na bacia do Sado (SW de Portugal). Cuad. Lab. Xeol. De Laxe 19, 229-238.
Quesada García, A. (1960): Falla de desgarre en el SW de la Península Ibérica. Notas y Comunicaciones de Instituo Geol. y Min. de España
seta Central Española). Estudios Geologicos 36, 391-401.García de Figuerola, L.C. (1963): El dique diabásico del norte de Extre-
madura. Not. Com. Inst. Geol. Min. España 69, 43-78.García de Figuerola, L.C. (1965): La continuación hacia el SO del dique
básico de Plasencia (Cáceres). Not. Com. Inst. Geol. Min. España: 77 p.
Gracia Prieto, F.J., Moreno, F., Nozal, F. (1991): Neotectonics and as-sociated seismicity in northwestern Duero Basin. Pub. IGN Mon. 8: 255-267.
Gonçalvez, F., Torre de Assunção, C. (1970): Noticia explicativa da floha 37-A (Elvas). Carta Geológica de Portugal na E. 1/50.000. Serviços Geológicos de Portugal: 50 p.
Gonçalvez, F., Torre de Assunção, C., Pinto Coelho, A.V. (1972): No-ticia explicativa da floha 33-C (Campomaior). Carta Geológica de Portugal na E. 1/50.000. Serviços Geológicos de Portugal: 41 p.
González-Casado, J. M., Giner Robles, J. (2000): Relaciones entre fallas y sismicidad en el Noroeste peninsular. Geogaceta 28: 71-75.
González Vallejo. L., Capote del Villar, R., Villamor Pérez , P., Ro-driguez Franco, J.A,. Tsige, M. (1997): Metodología de Evaluación de Riesgo Sísmico en segmentos de falla. ENRESA Pub. Tec. num. 02/97, Madrid: 205 p.
González Flores, M. (1996): Estudio estructural del sector norte de la falla de Plasencia-Alentejo (Provincia de Avila y Cáceres). Trabajo de Investigación del curso de Doctorado de Geología Estructural. Universitat Autonoma de Barcelona, Barcelona: 71 p.
Hanks, T. C., H. Kanamori (1979): A moment magnitude scale, J. Geophys. Res. 84, 2348– 2350. doi:10.1029/JB084iB05p02348.
Herráiz, M., De Vicente, G., Lindo-Ñaupari, R., Sanchez Cabañero, J.G. (1996): Seismotectonics of the Sierra Albarrana area (southern Spain); constraints for a regional model of the Sierra Morena-Gua-dalquivir Basin. Tectonophysics 266(1-4), 425-442. doi:10.1016/S0040-1951(96)00201-6.
Hernández-Pacheco, F., Crusafont Pairo, M. (1960): Primera caracteri-zación paleontológica del Terciario de Extremadura. Bol. R. Soc. Esp. Hist. Nat. 58, 275-283.
Herráiz, M., De Vicente, G., Lindo, R., Giner, J., Simón, J.L., Gonzá-lez Casado, J.M., Vadillo, O., Rodríguez Pascua, M.A., Cicuéndez, J.I., Casas, A., Cabañas, L., Rincón, P., Cortés, A., Ramírez, M., Lucini, M. (2000): The recent (upper Miocene to Quaternary) and present tectonic stress distributions in the Iberian Peninsula. Tecto-nics 19(4),762-786. doi:10.1029/2000TC900006.
ITGE (1995): (Baleares y Canarias) Mapa Geológico de la Península Ibérica E. 1:000.000. I.T.G.E., Madrid.
Lepvrier, C., Martínez-García, E. (1990): Fault develpoment and stress evolution of the post-Hercynian Asturian Basin (Asturias and Can-trabria, Spain). Tectonophysics 184, 345-356. doi:10.1016/0040-1951(90)90447-G.
López-Fernández, C., Pulgar, J. A., Gallart, J., Glez-Cortina, J. M., Díaz, J., Ruíz, M. (2004): Sismicidad y tectónica en el área de Be-cerreá-Triacastela (Lugo, NO España). Geogaceta 36, 51-54.
Martín-González, F. (2009): Cenozoic tectonic activity in a Variscan basement: Evidence from geomorphological markers and structur-al mapping (NW Iberian Massif). Geomorphology 107, 210-225. doi:10.1016/j.geomorph.2008.12.008.
Martín Herrero D., Bascones Alvira, L., Ugidos Meana, J.M. (1987a): Hoja geologica num. 623 (Malpartida de Plasencia). Mapa Geoló-gico de España, E. 1:50.000. Segunda serie, I.G.M.E., Madrid.
Martín Herrero, D., Bascones Alvira, L., Corretge Castañon, L. G. (1987b): Hoja geologica num. 650 (Cañaveral). Mapa geologico de Espana E. 1:50 000. Segunda serie, I.G.M.E., Madrid.
Martín Parra, L.M. (1987): Hoja geologica num. 128 (Riello). Mapa Geológico de España E. 1:50.000. Segunda serie, I.G.M.E., Ma-drid.
108 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
58, 163-182.Quigley, M., Van Dissen, R., Villamor, P., Litchfield, N., Barrell, D.,
Furlong, K., Stahl, T., Duffy, B., Bilderback, E., Noble, D., Town-send, D., Begg, J., Jongens, R., Ries, W., Claridge, J., Klahn, A., Mackenzie, H., Smith, A., Hornblow, S., Nicol, R., Cox, S., Lan-gridge, R., Pedley, K. (2010): Surface rupture of the Greendale Fault during the Mw 7.1 Darfield (Canterbury) earthquake, New Zealand: initial findings. Bulletin of the New Zealand Society for Earthquake Engineering 43(4), 236-242.
Quigley, M., Van Dissen, R., Litchfield, N., Villamor, P., Duffy, B., Barrell, D,, Furlong, K., Stahl, T., Bilderback, E, Noble, D. (2012): Surface rupture during the 2010 Mw 7.1 Darfield (Canterbury) earthquake: Implications for fault rupture dynamics and seismic-hazard analysis. Geology 40, 55-58. doi:10.1130/G32528.1.
Rincón, P.J., Hermosilla, J., Vegas, R., Pascual, G., Muñoz-Martín, A., Martínez-Solares, J.M. (2000): Cálculo automático del despla-zamiento en un sector del sistema falla-dique de Plasencia. Geoga-ceta 27, 143-146.
Rockwell, T., Fonseca, J., Madden, C., Dawson, T., Owen, L.A., Vi-lanova, S., Figueiredo, P. (2009): Paleoseismology of the Vilariça Segment of the Manteigas-Bragança Fault in Northeastern Portugal. Geol. Soc. London, Special Publication 316, 237-258. doi:10.1144/SP316.15.
Rodgers, D.A. (1980): Analysis of pull-apart basin development pro-duced by en echelon strike-slips faults. Spec. Publ. Int. Sediment. 4, 27-41.
Rueda, J., Mezcua, J. (2001): Sismicidad, sismotectónica y peligrosi-dad sísmica en Galicia. Publicación Técnica. Instituto Geográfico Nacional, Madrid: 64 p.
Sánchez-Serrano, F. (2000): Análisis de la Topografía y Deformacio-nes Recientes en el Centro de la Península Ibérica. PhD Thesis. University Complutense, Madrid (Spain): 202 p.
Santanach, P. (1994): Las cuencas terciarias gallegas en el marco tec-tónico regional. Cuad. Lab. Xelógico de Laxe 18, 57-71.
Santisteban, J.I., Martín-Serrano, A., Mediavilla, R. (1991): El Paleó-geno del sector suroccidental de la Cuenca de Duero: Nueva divisón estratigráfica y controles sobre su sedimentación. Acta Geológica Hispánica 26, 133-148.
Santisteban, J.I., Mediavilla, R., Martín-Serrano, A. (1996): The Due-ro Basin: a general overview. In: In: P.F. Friend, C.J. Dabrio (ed.), Tertiary Basins of Spain. World and regional geology series (6). Cambridge University Press, Cambridge, New York: 183-187.
Santos García, J.A., Casas Ruíz, J. (1982): Hoja geol. Num. 727 (Al-burquerque). Mapa Geológico de España E. 1:50.000. Segunda se-rie, I.G.M.E., Madrid.
SGE (Servicio Geográfico del Ejército) (1997): Mapa militar digital de España. E. 1:250.000 y 1:800.000. Version 1.5, Ministerio de Defensa, Madrid.
Srivastava, S. P., Roest, W. R., Kovacs, L. C., Oakey, G., Leves-que, S., Verhoef J. Macnab, R. (1990): Motion of Iberia since the Late Jurassic: Results from detailed aeromagnetic measure-ment in the Newfoundland Basin. Tectonophysics 184, 229-260. doi:10.1016/0040-1951(90)90442-B.
Stampfli, G., Borel, G. (2002): A plate tectonic model for Paleozoic and Mesozoic constrained by dynamic plate boundaries and reso-tred synthetic ocean isochrotnes. Earth and Planetary Science Let-ters 196, 17-33. doi:10.1016/S0012-821X(01)00588-X
Stirling, M.W., Rhoades, D., Berryman, K. (2002): Comparison of earthquake scaling relations derived from data of the instrumental and pre-instrumental eras. Bull. Seis. Soc. America 92 (2), 812-830. doi: 10.1785/ 0120000221.
Stirling, M.W., McVerry, G., Gerstenberger, Litchfield, N., Van Dis-
sen, R., Berryman, K., Barnes, P., Wallace, L., Bradley, B., Villa-mor, P., Langridge, R., Lamarche, G., Nodder, S., Reyners, M., Rhoades, D., Smith, W., Nicol, A., Pettinga, J., Clark, K., Jacobs. K. (2012): National Seismic Hazard Model for New Zealand: 2010 Update. Bull. Seis. Soc. America (in press).
Stirling, M. W., Wesnousky, S.G., Shimazaki, K. (1996): Fault trace complexity, cumulative slip, and the shape of the magnitude-fre-quency distribution for strike-slip faults; a global survey.Geophys. J. Int. 124(3), 833-868. doi: 10.1111/j.1365-246X.1996.tb05641.x.
Tsige, M., Capote, R., Villamor, P. (1997): Superficies de erosión y pa-leoalteraciones terciarias en Extremadura occidental: In: J. P. Calvo, J. Morales (ed.), Avances en el conocimiento del Terciario Ibérico. Univ. Complutense-Museo Nac. Ciencias Naturales, Madrid: 217-220.
Ugidos Meana, J.M., García de Figuerola, L. C., Bascones, A.L., Mar-tín Herrero, D. (1987a): Hoja geol. num. 598 (Plasencia). Mapa Geológico de España E. 1:50.000. Segunda serie, I.G.M.E., Ma-drid.
Ugidos Meana, J. M., Garcia de Figuerola, L. C., Bascones, A.L., Martin Herrero, D. (1987b). Hoja geol. num. 596 (Moraleja). Mapa Geológico de España. E. 1:50 000. Segunda serie, I.G.M.E., Ma-drid.
Ugidos Meana, J. M., Rodriguez Alonso, M. D., Martin Herrero, D., Bascones A.L. (1988): Hoja geol. num. 575 (Hervás). Mapa Geo-lógico de España. E. 1:50.000. Segunda serie, I.G.M.E., Madrid.
UNESCO (2011): World Heritage List. http://whc.unesco.org/en/list/. (Accessed 30-07-2011).
Vegas, R. (1974): Las fallas de desgarre del SO de la Península Ibéri-ca. Boletín Geológico y Minero 85, 153-156.
Vegas, R. (1975): Wrench (transcurrent) fault system of the south-western Iberian Peninsula: paleogeographic and morphostructural implications. Geologishe Rundschau 64, 266-278.
Villamor, M.P. (2002): Cinemática Terciaria y Cuaternaria de la Fa-lla de Alentejo-Plasencia y su Influencia en la Peligrosidad Sísmica del Interior de la Península Ibérica (Tertiary and Quaternary kine-matics of the Alentejo-Plasencia and its influence on sesimic hazard of the interior of Iberian Peninsula; in Spanish). PhD Thesis. Uni-versity Complutense, Madrid (Spain): 343 p.
Villamor, P., Barrell, D., Litchfield, N., Van Dissen, R., Hornblow, S., Levick, S. (2011): Greendale Fault investigation of surface rupture characteristics for fault avoidance zonation. GNS Science Consul-tancy Report 2011/121: 58 p.
Villamor, P., Capote, R., Tsige, M. (2004): Basement control on nu-cleation and geometry of the Alentejo-Plasencia Fault, western Spain. EGU, Nice 2004, Geophysical Research Abstracts 6: 2 p.
Villamor, P., Litchfield, N., Barrell, D., Van Dissen, R., Hornblow, S., Quigley, M., Levick, S., Ries, W., Duffy, B., Begg, J., Town-send, D., Stahl, T., Bilderback, E., Noble, D., Furlong, K., Grant, H. (2012): The 2010 Greendale Fault surface rupture map, Canterbury, New Zealand: Application to land use planning. New Zealand Jour-nal of Geology and Geophysics (in press)
Wells, D.L.; Coppersmith, K.J. (1994): New empirical relationships among magnitude, rupture length, rupture area, and surface displa-cement. Bull. Seis. Soc. of America 84, 974-1002.
Wesnousky, S.G. (1986): Earthquakes, Quaternary faults and seis-mic hazard in California. Jour. Geoph. Res. 91, 12.587-12.631. doi:10.1029/JB091iB12p12587.
Ziegler, P.A. (1989): Geodynamic model for Alpine intra-plate com-pressional deformation in Western and Central Europe. Geological Society London, Special Publications 44, 63-85. doi:10.1144/GSL.SP.1989.044.01.05.
109Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
App
endi
x 1
Para
met
ers o
f act
ive
or p
oten
tially
act
ive
faul
ts o
f the
Iber
ia in
trapl
ate
regi
on.
Tec
toni
c re
gion
w
ithin
the
in
trap
late
are
a Fa
ult
Azi
mut
h D
ip
Sens
e L
engt
h (k
m)
Tot
al h
oriz
. D
ispl
acem
. (k
m)
Tot
al v
ert.
disp
lace
m.
(km
)
Age
of m
ost r
ecen
t m
ovem
ent*
Hor
iz. D
ispl
ac.
mos
t rec
ent
mov
em. (
m)
Ver
t. di
spla
c.m
ost r
ecen
t m
ovem
. (m
)
Tot
al d
ispl
ac.
mos
t rec
ent
mov
em.(m
)
Hor
izon
tal
slip
rat
e (m
m/a
)
Ver
tical
sl
ip r
ate
(mm
/a)
Net
sl
ip r
ate
(mm
/a)
Ref
eren
ce
Ven
tani
ella
N
W-S
E
Strik
e-sl
ipe
230
4
early
Ple
isto
c (s
ed)
1 C
entro
Ast
uria
s E-
W
R
ever
se
90
Mio
cene
(sed
)
2,
3
Occ
Ast
uria
s N
NE-
SSW
Rev
erse
10
M
ioce
ne (s
ed)
4 N
Due
ro
E-W
Rev
erse
5,
3
A1
Le
on
E-W
Strik
e-sl
ipe
140
Turo
l-lat
e Pl
ioc
75
-100
0.
015-
0.06
5, 3
C
anta
bric
a
Sabe
ro-G
ordó
n E-
W
St
rike-
slip
e 11
0
(e
arly
Ple
isto
cene
)
10
0.01
2-0.
05
5,
3
y M
onte
s de
Porm
a EN
E-W
SW
St
rike-
slip
e 45
3 G
alic
ia-L
eon
Gal
icia
Sur
N
W-S
E
Strik
e-sl
ipe
M
ioce
ne
4, 6
G
alic
ia N
orte
N
W-S
E
Strik
e-sl
ipe
M
ioce
ne
4, 6
G
alic
ia C
entro
N
W-S
E
Strik
e-sl
ipe
M
ioce
ne
4, 6
S
arria
N
NE-
SSW
Rev
erse
- St
rike-
slip
e
Mio
cene
4,
6, 7
Mon
tforte
N
NE-
SSW
Rev
erse
- St
rike-
slip
e
Mio
cene
4,
6
Bie
rzo
E-W
Rev
erse
Mio
cene
4,
6, 8
N
orte
Sis
t.Cen
tral
ENE-
WSW
Rev
erse
9
Sur
Sis
t.Cen
tral
ENE-
WSW
Rev
erse
~3
9, 1
0, 1
1 A
2 Se
ia-L
ousa
N
E-SW
35
R
ever
se
100
Plio
cene
(Rañ
a)
60
0.
075-
0.1
13
Si
stem
a So
brei
ra-G
rade
N
E-SW
Rev
erse
45
Pl
ioce
ne (R
aña)
13
C
entra
l So
brei
ra-G
rade
N
E-SW
Nor
mal
15
Pl
ioce
ne (R
aña)
13
P
onsu
l N
E-SW
50
R
ever
se
120
1.5
Pl
ioc
(Rañ
a) 2
.5 -2
Ma
50
-100
65
-130
0.02
6-0.
065
13
, 14
Pon
sul
NE-
SW
R
ever
se
Pl
eist
ocen
e 0.
3 a
0.1
Ma
10
0.
03-0
.1
13
, 14
Naz
are-
Pom
bal
NE-
SW
R
ever
se
Pl
ioc
(Rañ
a) 3
-2.5
Ma
17
5
0.
058-
0. 0
7
13
Naz
are-
Pom
bal
NE-
SW
R
ever
se
R
aña
2-1.
6 M
a
150
0.07
5-0.
094
13
A
3 Si
erra
M
oren
a Si
erra
Alb
arra
na
E-W
/ N
W-
SE
N
orm
al-
strik
e-sl
ipe
15, 1
6
Por
tilla
s E-
W
no
rmal
50
?
Rañ
a
17
B
1 M
onte
Cha
o N
-S
St
rike-
slip
e -
reve
rse
90
mid
dle-
uppe
r Ple
is.
(100
-200
)
13
Mes
eta
M
ante
igas
-Bra
ganç
a N
E-SW
Strik
e-sl
ipe
250
8
2.5
-2 M
a 10
00
150-
200
0.
4-0.
5 0.
06-0
.1
13
, 18
Nor
te
Man
teig
as-B
raga
nça
NE-
SW
St
rike-
slip
e 25
0 8
m
iddl
e-up
per
Plei
stoc
ene
(100
-200
)
15-2
0
0.
075-
0.2
13
, 18
Pen
acov
a-V
erin
N
E-SW
Strik
e-sl
ipe
200
3.4
Pl
ioce
ne /Q
uate
rnar
y
100
13
N C
uenc
a G
uadi
ana
EN
E-W
SW
R
ever
se
M
ioce
ne
this
stud
y B
2 B
éjar
N
E-SW
Rev
erse
60
19
Mes
eta
Sur
Ale
ntej
o-Pl
asen
cia
NE-
SW
St
rike-
slip
e
3.3
??
this
stud
y A
lent
ejo-
Plas
enci
a N
E-SW
Strik
e-sl
ipe
2.
5-2
Ma
100
14
0
0.04
-0.0
5 0.
07-0
.056
13
V
idig
ueira
-Mou
ra
N 1
00
R
ever
se
65
Plei
stoc
ene
50 (r
aña)
0.
035-
0.09
5
20
Vid
igue
ira -M
oura
N
101
Rev
erse
2 M
a
10-3
0
0.
005-
0.01
5
13
Sor
-Mon
tene
gril
NE-
SW
St
rike-
slip
e
13
T
ejo
Infe
rior
NE-
SW
N
orm
al -
strik
e-sl
ipe
28
65-2
490
BC
3.
5
0.
72-0
.78
13
Tej
o In
ferio
r N
E-SW
Nor
mal
- st
rike-
slip
e
365-
655A
D
0.7
0.54
-0.4
4 21
Gra
ndol
a W
NW
-ESE
Nor
mal
31
-65
2.5
- 2 M
a
150
0.06
-0.0
75
13
R
efer
ence
: 1
= N
ozal
and
Gra
cia
(199
0); 2
= L
epvr
ier a
nd M
artín
ez-G
arcí
a (1
990)
; 3 =
Alo
nso
et a
l. (1
996)
; 4 =
Mar
tín-S
erra
no e
t al.
(199
6).
5
= Sa
ntis
teba
n et
al.
(199
6); 6
= S
anta
nach
(199
4); 7
= M
artín
ez-D
iaz
et a
l. (2
006)
; 8 =
Mar
tín P
arra
(198
7).
9
= S á
nche
z-Se
rran
o (2
000)
; 10
= D
e V
icen
te e
t al.
(199
6); 1
1 =
Cal
vo e
t al.
(199
3);
13
= C
abra
l (19
95);
14 =
Mor
eno
Serr
ano
(199
0); 1
5 =
Gon
z ále
z V
alle
jo e
t al.
(199
7); 1
6 =
Her
raiz
et a
l. (1
996)
.
17 =
Gra
cia
Prie
to e
t al.
(199
1); 1
8 =
Dia
s and
Cab
ral (
1991
); 19
= B
asco
nes –
Alv
ira a
nd M
artín
Her
erro
(198
7).
20
= B
rum
da
Silv
eira
(199
0); B
rum
a da
Silv
eira
et a
l. (2
009)
; 21
= Fo
nsec
a et
al.
(200
0).
110 Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
App
endi
x 2.
Se
ism
ic p
aram
eter
s of a
ctiv
e or
pot
entia
lly a
ctiv
e fa
ults
of t
he Ib
eria
intra
plat
e ar
ea (S
R: s
lip ra
te; M
w: m
omen
t mag
nitu
de; R
I: re
curr
ence
inte
rval
)
Faul
tSe
nse,
azi
mut
h, d
ip
(deg
rees
) Se
gmen
tatio
n m
odel
Se
gmen
t na
me
Len
gth
(km
) SR Max
. SR mea
nSR M
in.
Mw
W &
C (R
A)4
Mw,
And
erso
n4
(SR
min
-SR
max
)
Mw
,St
irlin
g4
pos 1
900
Mw
, B
erry
man
200
24R
I,(M
ax.)
RI,
(Min
.)
Ven
tani
ella
3St
ryke
-slip
, 0, 9
0
Min
imum
A
ll 16
3,0
0,1
0,05
0,
01
7.51
8.
09 -
7.89
7.
64
8.00
17
3406
2 23
945
Max
imum
Ven
1 30
,3
0,1
0,05
0,
01
6.80
7.
24 -
7.04
7.
06
7.02
49
9018
10
855
Ven
2 29
,7
0,1
0,05
0,
01
6.79
7.
23 -
7.03
7.
05
7.01
49
1687
10
754
Ven
3 28
,5
0,1
0,05
0,
01
6.77
7.
21 -
7.01
7.
04
6.99
47
6907
10
434
Ven
4 20
,6
0,1
0,05
0,
01
6.63
7.
04 -
6.84
6.
93
6.80
37
5068
82
06
Ven
5 28
,7
0,1
0,05
0,
01
6.77
7.
21 -
7.01
7.
04
6.99
47
9382
10
488
Ven
6 25
,3
0,1
0,05
0,
01
6.72
7.
15 -
6.95
7.
00
6.92
43
6675
95
53
Las P
ortil
las2g
Nor
mal
, 180
, 45
Min
imum
A
ll 69
,0
0,03
0,
025
0,02
7.
44
7.77
- 7.
73
7.46
7.
80
3815
62
6117
9
Max
imum
Lp
o1
42,1
0,
03
0,02
5 0,
02
7.08
7.
34 -
7.31
7.
17
7.31
18
2666
32
800
Lpo2
55
,6
0,03
0,
025
0,02
7.
20
7.48
- 7.
45
7.27
7.
47
2245
69
4032
4
Reg
ua-V
erín
2b
Stry
ke-s
lip, 0
, 90
Min
imum
A
ll 26
5,0
0,14
0,
09
0,04
7.
77
8.27
- 8.
16
7.84
8.
34
5769
54
2260
9
Max
imum
Re-
Ve1
48
,5
0,14
0,
09
0,04
7.
00
7.36
- 7.
25
7.22
7.
30
1165
79
9672
R
e-V
e2
48,4
0,
14
0,09
0,
04
7.00
7.
35 -
7.25
7.
22
7.29
11
6401
96
63
Re-
Ve3
28
,3
0,14
0,
09
0,04
6.
77
7.08
- 6.
97
7.04
6.
98
7825
2 74
14
Re-
Ve4
38
,2
0,14
0,
09
0,04
6.
90
7.24
- 7.
13
7.14
7.
16
9777
6 86
50
Re-
Ve5
47
,1
0,14
0,
09
0,04
6.
98
7.34
- 7.
23
7.21
7.
28
1140
79
9540
R
e-V
e6
40,4
0,
14
0,09
0,
04
6.92
7.
26 -
7.15
7.
16
7.19
10
1834
88
76
Re-
Ve7
44
,4
0,14
0,
09
0,04
6.
96
7.31
- 7.
20
7.19
7.
24
1092
03
9279
Man
teig
as-B
raga
nça1b
Stry
ke-s
lip, 0
, 90
Min
imum
A
ll 25
0,0
0,7
0,4
0,06
7.
68
8.13
- 7.
92
7.77
8.
23
3149
08
4116
Max
imum
Ma-
Br1
70
,2
0,7
0,4
0,06
7.
15
7.51
- 7.
29
7.35
7.
51
9142
5 23
02
Ma-
Br2
47
,4
0,7
0,4
0,06
6.
99
7.31
- 7.
09
7.21
7.
28
6765
9 19
14
Ma-
Br3
40
,5
0,7
0,4
0,06
6.
92
7.23
- 7.
02
7.16
7.
19
6022
4 17
77
Ma-
Br4
45
,3
0,7
0,4
0,06
6.
97
7.29
- 7.
07
7.20
7.
26
6542
8 18
73
Ma-
Br5
38
,4
0,7
0,4
0,06
6.
90
7.20
- 6.
99
7.14
7.
16
5789
7 17
33
Pons
ul1b
,cR
ever
se, 3
15,4
0
Min
imum
A
ll 11
6,0
0,1
0,07
0,
03
7.47
7.
81 -
7.71
7.
51
7.87
29
6493
22
271
Max
imum
Po
n1
32,1
0,
1 0,
07
0,03
6.
93
7.17
- 7.
07
7.08
7.
13
9564
4 87
28
Pon2
28
,8
0,1
0,07
0,
03
6.89
7.
12 -
7.01
7.
04
7.07
88
266
8055
Po
n3
27,4
0,
1 0,
07
0,03
6.
87
7.09
- 6.
99
7.03
7.
04
8507
1 77
63
Pon4
25
,5
0,1
0,07
0,
03
6.84
7.
06 -
6.95
7.
00
7.00
80
735
7368
Tejo
Infe
rior2d
Rev
erse
,130
, 35
Min
imum
A
ll 83
,0
0,8
0,4
0,01
7.
40
7.85
- 7.
47
7.48
7.
79
1010
112
2647
Max
imum
Te
-In1
36
,7
0,8
0,4
0,01
6.
96
7.34
- 6.
95
7.13
7.
19
4710
49
1288
Te
-In2
32
,1
0,8
0,4
0,01
6.
91
7.27
- 6.
89
7.08
7.
11
4266
06
1167
Te
-In3
34
,1
0,8
0,4
0,01
6.
93
7.30
- 6.
92
7.10
7.
15
4460
23
1220
Rio
Sor-
Mon
terg
il1b
Rev
erse
, 130
,35
Min
imum
A
ll 12
8,0
0,1
0,05
0,
01
7.36
7.
80 -
7.60
7.
44
7.73
93
4864
20
162
Max
imum
So
-Mo1
31
,1
0,1
0,05
0,
01
6.89
7.
25 -
7.05
7.
07
7.10
41
6632
91
15
So-M
o2
29,5
0,
1 0,
05
0,01
6.
87
7.22
- 7.
02
7.05
7.
06
4006
57
8765
So
-Mo3
32
,1
0,1
0,05
0,
01
6.91
7.
27 -
7.07
7.
08
7.11
42
6508
93
31
Seis
a-Lo
usa1b
Rev
erse
, 140
,35
Min
imum
A
ll 88
,0
0,17
0,
12
0,07
7.
39
7.67
- 7.
59
7.47
7.
77
1108
49
1225
2
Max
imum
Se
-Lo1
33
,9
0,17
0,
12
0,07
6.
93
7.13
- 7.
05
7.10
7.
15
3784
3 57
16
Se-L
o2
29,5
0,
17
0,12
0,
07
6.87
7.
06 -
6.98
7.
05
7.06
32
931
5157
Se
-Lo3
35
,9
0,17
0,
12
0,07
6.
95
7.15
- 7.
08
7.12
7.
18
4007
5 59
64
Naz
are-
Pom
bal1b
Rev
erse
, 130
, 35
Min
imum
A
ll 92
,0
0,1
0,08
0,
06
7.45
7.
76 -
7.71
7.
52
7.86
15
0773
22
386
Max
imum
N
a-Po
1 33
,8
0,1
0,08
0,
06
6.93
7.
14 -
7.09
7.
10
7.14
43
954
9686
N
a-Po
2 33
,1
0,1
0,08
0,
06
6.92
7.
13 -
7.08
7.
09
7.13
43
056
9539
N
a-Po
3 49
,0
0,1
0,08
0,
06
7.09
7.
32 -
7.28
7.
22
7.36
63
763
1275
5 V
idig
ueira
-Mou
ra1b
R
ever
se, 0
, 35
V
i-Mo
39,4
0,
1 0,
08
0,01
6.
99
7.37
- 7.
17
7.15
7.
23
4961
76
1085
5
Sobr
eira
-Gra
de1b
Rev
erse
, 310
, 35
Min
imum
A
ll 66
,0
0,1
0,05
0,
01
7.19
7.
60 -
7.40
7.
31
7.49
69
4357
15
191
Max
imum
So
-Gr1
34
,0
0,1
0,05
0,
01
6.93
7.
30 -7
.10
7.10
7.
15
4451
51
9739
So
-Gr2
28
,0
0,1
0,05
0,
01
6.85
7.
20 -
7.00
7.
03
7.03
38
5576
84
35
Due
ro N
orte
3 R
ever
se, 1
90, 3
5
No-
Du
60,0
0,
1 0,
05
0,01
7.
17
7.58
- 7.
38
7.29
7.
48
6777
12
1482
7
Leon
3
Obl
ique
stry
ke-s
lip, 0
, 70
Min
imum
A
ll 12
6,0
0,1
0,05
0,
01
7.79
7.
88 -
7.68
7.
50
8.07
84
4157
95
66
Max
imum
Le
on1
18,8
0,
1 0,
05
0,01
7.
05
7.00
- 6.
80
6.90
7.
06
1466
71
2620
Le
on2
29,9
0,
1 0,
05
0,01
7.
25
7.23
- 7.
03
7.06
7.
33
2336
41
3697
Le
on3
28,6
0,
1 0,
05
0,01
7.
23
7.21
- 7.
01
7.04
7.
30
2234
83
3578
Le
on4
30,8
0,
1 0,
05
0,01
7.
26
7.25
- 7.
05
7.07
7.
34
2403
62
3776
Sabe
ro-G
ordo
n3O
bliq
ue st
ryke
-slip
, 0, 7
0 M
inim
um
All
69,0
0,
1 0,
05
0,01
7.
60
7.65
- 7.
45
7.34
7.
81
5376
10
6850
Max
imum
Sa
-Go1
34
,4
0,1
0,05
0,
01
7.31
7.
30 -
7.10
7.
10
7.41
26
8492
40
98
Sa-G
o2
34,4
0,
1 0,
05
0,01
7.
31
7.30
- 7.
10
7.10
7.
41
2691
17
4105
Porm
a3St
ryke
-slip
, 0, 9
0 M
inim
um
All
56,0
0,
1 0,
05
0,01
7.
05
7.54
- 7.
34
7.26
7.
37
7757
42
1436
6
Max
imum
Po
rma1
23
,5
0,1
0,05
0,
01
6.69
7.
11 -
6.91
6.
97
6.88
41
3726
90
51
Porm
a2
31,5
0,
1 0,
05
0,01
6.
81
7.26
- 7.
06
7.07
7.
04
5133
27
1105
2
111Villamor et al. / Journal of Iberian Geology 38 (1) 2012: 85-111
App
endi
x 2
cont
. Se
ism
ic p
aram
eter
s of a
ctiv
e or
pot
entia
lly a
ctiv
e fa
ults
of t
he Ib
eria
intra
plat
e ar
ea (S
R: s
lip ra
te; M
w: m
omen
t mag
nitu
de; R
I: re
curr
ence
inte
rval
)
Faul
tSe
nse,
azi
mut
h, d
ip
(deg
rees
) Se
gmen
tatio
n m
odel
Se
gmen
t na
me
Len
gth
(km
) SR Max
. SR mea
nSR M
in.
Mw
W &
C (R
A)4
Mw,
And
erso
n4
(SR
min
-SR
max
)
Mw
,St
irlin
g4
pos 1
900
Mw
, B
erry
man
200
24R
I,(M
ax.)
RI,
(Min
.)
Sist
ema
Cen
tral S
3R
ever
se, 3
20, 3
5
Min
imum
A
ll 24
0,0
0,1
0,05
0,
01
7.72
8.
23 -
8.03
7.
74
8.22
17
5825
1 30
115
Max
imum
SSiC
en1
37,7
0,
1 0,
05
0,01
6.
97
7.35
- 7.
15
7.14
7.
21
4805
14
1051
2 SS
iCen
2 37
,8
0,1
0,05
0,
01
6.98
7.
35 -
7.15
7.
14
7.21
48
1457
10
533
SSiC
en3
38,0
0,
1 0,
05
0,01
6.
98
7.35
- 7.
15
7.14
7.
21
4833
40
1057
4 SS
iCen
4 34
,2
0,1
0,05
0,
01
6.93
7.
30 -
7.10
7.
10
7.15
44
7088
97
81
SSiC
en5
34,4
0,
1 0,
05
0,01
6.
94
7.30
- 7.
10
7.10
7.
15
4490
21
9824
SS
iCen
6 35
,5
0,1
0,05
0,
01
6.95
7.
32 -
7.12
7.
11
7.17
45
9602
10
055
Sist
ema
Cen
tral N
3R
ever
se, 1
40, 3
5 M
inim
um
All
79,0
0,
1 0,
05
0,01
7.
28
7.71
- 7.
51
7.38
7.
62
8127
59
1778
1
Max
imum
N
SiC
en1
38,0
0,
1 0,
05
0,01
6.
98
7.35
- 7.
15
7.14
7.
21
4833
40
1057
4 N
SiC
en2
38,7
0,
1 0,
05
0,01
6.
99
7.36
- 7.
16
7.14
7.
22
4899
13
1071
8 M
onte
Cha
o1b
Rev
erse
-stry
ke-s
lip, 9
0,50
MoC
hao
55,5
0,
1 0,
05
0,01
7.
24
7.54
- 7.
34
7.27
7.
50
5022
55
1098
8 G
rand
ola2e
N
orm
al, 1
80,7
0
Gra
nd
52,5
0,
075
0,07
0,
06
7.49
7.
36 -
7.34
7.
25
7.65
68
373
7478
B
éjar
R
ever
se, 1
40,3
5
Bej
55
,5
0,1
0,05
0,
01
7.14
7.
54 -
7.34
7.
27
7.43
63
9720
13
996
Gua
dian
aN-G
uada
lupe
3
Rev
erse
, 320
, 40
Min
imum
A
ll 17
3,0
0,1
0,05
0,
01
7.65
8.
11 -
7.91
7.
66
8.10
13
8104
2 27
819
Max
imum
NG
uad1
28
,5
0,1
0,05
0,
01
6.88
7.
21 -
7.01
7.
04
7.06
36
5332
79
93
NG
uad2
33
,0
0,1
0,05
0,
01
6.95
7.
28 -
7.08
7.
09
7.15
40
7196
89
08
NG
uad3
40
,0
0,1
0,05
0,
01
7.03
7.
38 -
7.18
7.
16
7.26
46
9491
10
271
NG
uad4
35
,3
0.1
0.05
0.
01
6.98
7.
32 -
7.12
7.
11
7.19
42
8012
93
64
NG
uad5
35
.1
0.1
0.05
0.
01
6.97
7.
31 -
7.11
7.
11
7.18
42
6216
93
25
Alb
arra
na3
Nor
mal
-stry
ke-s
lip, 0
, 90
Min
imum
A
ll 65
.0
0.1
0.05
0.
01
7.19
7.
71 -
7.51
7.
38
7.56
99
4110
16
817
Max
imum
A
lbar
r1
37,8
0.
1 0.
05
0.01
6.
89
7.35
- 7.
15
7.14
7.
15
5877
50
1204
4 A
lbar
r2
39.1
0.
1 0.
05
0.01
6.
91
7.37
- 7.
17
7.15
7.
17
6026
42
1223
7 Sa
rria
3 R
ever
se, 3
15, 4
0
Sarr
ia
28.5
0.
1 0.
05
0.01
6.
88
7.21
- 7.
01
7.04
7.
06
3653
32
7993
Mon
tforte
3R
ever
se, 3
35, 4
0 M
inim
um
All
40.5
0.
1 0.
05
0.01
7.
03
7.38
- 7.
18
7.16
7.
27
4738
27
1036
6
Max
imum
M
ontf1
20
,3
0,1
0,05
0,
01
6.74
7.
04 -
6.84
6.
92
6.87
28
4217
62
18
Mon
tf2
20,2
0,
1 0,
05
0,01
6.
74
7.03
- 6.
83
6.92
6.
86
2826
61
6184
Bie
rzo3
Rev
erse
, 0, 4
0
Min
imum
A
ll 97
,6
0,1
0,05
0,
01
7.41
7.
83 -
7.63
7.
46
7.78
90
8301
19
871
Max
imum
B
ierz
1 32
,7
0,1
0,05
0,
01
6.94
7.
28 -
7.08
7.
09
7.14
40
4178
88
42
Bie
rz2
36,8
0,
1 0,
05
0,01
6.
99
7.34
- 7.
14
7.13
7.
21
4409
54
9647
B
ierz
3 28
,2
0,1
0,05
0,
01
6.88
7.
20 -
7.00
7.
04
7.06
36
2102
79
22
Gal
icia
Sur
3St
ryke
-slip
, 0, 9
0 M
inim
um
All
66,1
0,
1 0,
05
0,01
7.
13
7.63
- 7.
43
7.33
7.
47
8891
85
1566
7
Max
imum
G
aliS
1 30
,8
0,1
0,05
0,
01
6.80
7.
25 -
7.05
7.
07
7.03
50
5584
10
946
Gal
iS2
35,3
0,
1 0,
05
0,01
6.
86
7.32
- 7.
12
7.11
7.
11
5587
30
1166
3
Gal
icia
Nor
te3
Stry
ke-s
lip, 0
, 90
Min
imum
A
ll 52
,2
0,1
0,05
0,
01
7.03
7.
51 -
7.31
7.
25
7.34
74
6002
14
014
Max
imum
G
aliN
23
,5
0,1
0,05
0,
01
6.69
7.
11 -
6.91
6.
97
6.87
41
2814
90
31
Gal
iN
28,7
0,
1 0,
05
0,01
6.
77
7.21
- 7.
01
7.04
6.
99
4796
29
1049
3
Gal
icia
Cen
tral3
Stry
ke-s
lip, 0
, 90
Min
imum
A
ll 43
,9
0,1
0,05
0,
01
6.95
7.
43 -
7.23
7.
19
7.24
65
6446
12
920
Max
imum
G
aliC
1 18
,8
0,1
0,05
0,
01
6.59
7.
00 -
6.80
6.
90
6.75
35
1082
76
81
Gal
iC2
25,1
0,
1 0,
05
0,01
6.
72
7.14
- 6.
94
7.00
6.
91
4334
77
9483
Ast
uria
s Cen
tral3
Inve
rsa,
0, 3
0 M
inim
um
All
53,6
0,
1 0,
05
0,01
7.
10
7.52
- 7.
32
7.26
7.
39
6582
05
1440
0
Max
imum
A
sC1
21,1
0,
1 0,
05
0,01
6.
70
7.06
- 6.
86
6.94
6.
85
3306
35
7233
A
sC2
32,4
0,
1 0,
05
0,01
6.
89
7.27
- 7.
07
7.08
7.
10
4541
33
9935
Ast
uria
s Occ
iden
tal3
Nor
mal
, 0,5
0 M
inim
um
All
46,0
0,
1 0,
05
0,01
7.
16
7.45
- 7.
25
7.20
7.
39
4361
72
9542
Max
imum
A
stO
1 24
,4
0,1
0,05
0,
01
6.89
7.
13 -
6.93
6.
99
7.03
27
3265
59
78
Ast
O2
21,5
0,
1 0,
05
0,01
6.
84
7.07
- 6.
87
6.94
6.
95
2488
40
5444
Ale
ntej
o-Pl
asen
cia1f
Stry
ke-s
lip, 0
, 90
Min
imum
A
ll 50
0 0,
1 0,
05
0,01
7.
99
8.65
- 8.
45
8.02
8.
65
3972
707
4054
0
Max
imum
AP1
-Muñ
ico
41,8
8 0,
1 0,
05
0,01
6.
93
7.40
- 7.
20
7.17
7.
21
6340
65
1263
9 A
P2 -B
arco
25
,73
0,1
0,05
0,
01
6.73
7.
16 -
6.96
7.
00
6.93
44
2155
96
73
AP3
-Jer
te
63,7
0,
1 0,
05
0,01
7.
11
7.61
- 7.
41
7.32
7.
45
8647
93
1539
2 A
P4 -C
añav
e 43
,15
0,1
0,05
0,
01
6.95
7.
42 -
7.22
7.
18
7.23
64
8238
12
818
AP5
-Bro
zas
26,8
0,
1 0,
05
0,01
6.
74
7.18
- 6.
98
7.02
6.
95
4556
89
9969
A
P6-A
lised
a 34
,13
0,1
0,05
0,
01
6.85
7.
30 -
7.10
7.
10
7.09
54
4966
11
480
AP7
-Alb
urq
20,8
7 0,
1 0,
05
0,01
6.
64
7.05
- 6.
85
6.93
6.
81
3787
00
8285
A
P8 -C
ampo
22
,31
0,1
0,05
0,
01
6.67
7.
08 -
6.88
6.
96
6.85
39
7867
87
04
AP9
28
,02
0,1
0,05
0,
01
6.76
7.
20 -
7.00
7.
03
6.98
47
0950
10
303
AP1
0 32
,82
0,1
0,05
0,
01
6.83
7.
28 -
7.08
7.
09
7.07
52
9409
11
271
AP1
1 41
,13
0,1
0,05
0,
01
6.93
7.
39 -
7.19
7.
17
7.20
62
5642
12
532
AP1
2 44
0,
1 0,
05
0,01
6.
96
7.43
- 7.
23
7.19
7.
24
6576
63
1293
6 A
P13
75
0,1
0,05
0,
01
7.18
7.
70 -
7.50
7.
37
7.55
97
5875
16
620
1 Val
ues f
rom
the
fow
ollin
g st
udie
s: b C
abra
l (19
95);
c Dia
s and
Cab
ral (
1991
); f th
is st
udy.
2 D
eriv
ed v
alue
s fro
m d
ata
in: d Fo
nsec
aet
al.
(200
0); e Pi
men
tel a
nd A
zeve
do (1
989)
; Pim
ente
l (19
97);
g Gra
cia
Prie
to e
t al.
(199
1).
3 Faul
ts w
ith n
o da
ta. P
aram
eter
val
ues f
rom
APF
(min
imum
act
ivity
). 4 M
omen
t mag
nitu
de fr
om sc
alin
g re
latio
nshi
ps: W
&C
=Wel
ls a
nd C
oppe
rsm
ith (1
994)
; And
erso
n=A
nder
son
et a
l. (1
996)
; Stir
ling=
Stirl
ing
et a
l. (2
002)
(pos
190
0); B
erry
man
200
2=B
erry
man
et a
l. (2
002)
.