Controlli per terminali apr 07

FANCOILS CONTROLSELECTRONIC BOARD - KCMS CMS - KCMS/PCM CMSPCMNEW WIRED CONTROL PANEL- KPCM

Controlli per terminali apr 07 n.2

FUNCTIONSFUNCTIONS

Controlli per terminali apr 07 n.3

IDROWALLIDROWALLIDROWALLIDROWALL

FRENDFRENDFRENDFREND

UTNBUTNBUTNBUTNB

CONTROLLI

UTNAUTNAUTNAUTNA

YARDYEVYARDYEVYARDYEVYARDYEV

BRIOEVBRIOEVBRIOEVBRIOEV

UTNC-EVUTNC-EVUTNC-EVUTNC-EV

IDROWALL FREND BRIOEV UTNC-EV

CONTROLLI

KPCMKTCMKICM

Controlli per terminali apr 07 n.4

CMS KCMS

CMSPCM KCMS/PCM

STI KSTI MVR KMVRRI-KRI

CONTROLSCONTROLS

KPCM

KTCM

KICM

Controlli per terminali apr 07 n.5

CMSPCM KCMS/PCM

KPCM

n. 46Eunit-systemPrice List

ADVANCED CONTROLS

Controls supplied loose to be mounted in the unit

YardyEV

EuroYardyEVKCMS - Master/slave electronic board

Euro

Euro

Euro

Controls factory fittedYardyEV

EuroYardyEVCMS - Master / slave electronic board

Euro

EuroSTI - Temperature sensor for additional water coil EuroMVR - Module ON/OFF valve Euro

Wired panelYardyEV

Euro

Wall-fitted control panel YardyEV

Euro

Serial interfaces supplied loose for connection with CMS and KCMS YardyEVKISI - Can-bus serial interface

EuroKRS485 - RS485 serial interface

EuroKRS232 - RS485/RS232 serial converter

EuroKUSB - RS485/USB serial converter

Euro

MVP - MVT VERSIONSKCMS/PCM - Master electronic board+ wired control panel (for MVP and MVT)

(E500200330)* E500200331147,00

ALL VERSIONS

(E500200350)* E50020035295,00

KSTI - Temperature sensor for additional water coil for connec tion to KCMS

E50020042015,00

KMVR - Module for ON/OFF valves E50020040043,00

MVP - MVT VERSIONSCMSPCM - Master electronic board + wired control panel (for MVP and MVT)

CMSPCM162,00

ALL VERSIONS

CMS110,00

RI - Infrared receiver RI45,00

STI16,00

MVR47,00

ALL VERSIONSKPCM - Control panel controlled by wire. Wall mounted. (E500200290)* E500200291

52,00

ALL VERSIONS

KICM - Wall-fitted control panel with LCD dispaly to be connected to KCMS.

E968573499

ALL VERSIONSE500200295

60,00

293,00

E968573497293,00

69,00

E96857349475,00

E968573496

CMS KCMS

New codes for electrical board and panel

(E500200330)* E500200331

CONTROLSCONTROLS

* ATTENTION: the codes into brackets are available until may 2007. The close codes (without brackets) will be available afterward, according to Circular Letter

Controlli per terminali apr 07 n.6

New electronic board KCMS CMS

SCR ECO digital input don’t change, SIC EIR change their position New digital input DI5 (not available for Frend and Idrowall) for new function:

OCCUPANCY function (NC) only for KICM panel, (by modifying board parameters (P45=8;P93=3) trough installer password on the KPCM control panel)

Controlli per terminali apr 07 n.7

New electronic board KCMS CMS

New digital output CCH CCA

Controlli per terminali apr 07 n.8

FUNCTIONS SETTING FUNCTIONS

COMFORT FUNCTIONS

Controlli per terminali apr 07 n.9

FUNCTIONS

NOVELTY•Full AUTO: the desired temperature is showed on the display. The unit, according to the room temperature and the setting temperature, sets the working mode (cool/heat).

SETTING FUNCTIONS1. Full auto 2. Cool3. Dry 4. Fan 5. Heat 6. Heat + heater7. Full Auto + heater

KPCMKTCM

KICM

User set temperature

P02=2°C

P03=2°C

P04=0,5°C

P04=0,5°C

mode

room temperature

HEAT

OFF

COOL

Legend

Controlli per terminali apr 07 n.10

FUNCTIONS

ATTENTION•The following functions aren’t available with KICM control panel:

•Orienting/swing - Clock - Timer - Continuous ventilation (by key) – Keybord stop •Probe IN/OUT function is available for:

KICM trough DIP SWITCH (DIP6) setting KPCM trough key on the panel Not used with the remote control KTCM (the probe is always set in the unit)

•The periodic ventilation is always disabled with KPCM and KICM with Probe In function activated (probe into the unit)•Confort control (by modifying board parameters P36=1 trough installer password on the KPCM control panel).

COMFORT FUNCTIONS1. Orienting/swing (on Idrowall)

2. Clock3. Timer4. Sleep5. Hot start6. Too cool7. Memory

11. Economy (ECO)12. Lock function / Blocco remoto (KICM)13. ON/OFF remote control (SCR)14. Summer/Winter remote control (EIR)15. Security control (SIC)16. Occupancy (only KICM) new 17. Probe IN/OUT18. Continuous ventilation19. Alarm20. MASTER/SLAVE21. Periodic ventilation22. Confort control new 23. Blocco tastiera (solo KTCM)

KPCMKTCM

KICM

Controlli per terminali apr 07 n.11

User set temperature

P02=2°C

P03=2°C

P04=0,5°C

P04=0,5°C

mode

room temperature

HEAT

OFF

COOL

Legend

COMFORT CONTROL FUNCTIONComfort control (by parameters)

When the set-point is decided by a system manager (supervision), the Comfort Control function gives the possibility to increase or reduce the Set-point (+-3°C) in the room with the UP-DOWN bottoms.(The function have to be enable modifying board parameters P36=1 trough installer password on the KPCM control panel.)The set value is 22 °C

22°C

Controlli per terminali apr 07 n.12

LOCK FUNCTION FUNCTION

Attention: to obtain the changing set-point ±3°C must be set the Confort Control Function

Controlli per terminali apr 07 n.13

Changes to the DIP-Switches must be made with the board disconnected from the power supply. The DIP-Switches on the electronic board (see right figure) can be changed using a sharp tool. The DIP-

Switches can be changed correctly by following the instructions present on the component and in the following table.

DIP-SWITCHES

Controlli per terminali apr 07 n.15

CCH

Chiller input, chilled water required from the thermostat (NO)

DIGITAL OUTPUT: FUNCTION

CCH –Chiller input

Controlli per terminali apr 07 n.16

CCA

Boiler input, hot water required from the thermostat (NO)

DIGITAL OUTPUT: FUNCTION

CCA – Boiler input