Home > Documents > COOPER CAMERON VALVES CAMERON ARGENTINA S.A.I.C. …

COOPER CAMERON VALVES CAMERON ARGENTINA S.A.I.C. …

Date post: 13-Nov-2021
Category:
Author: others
View: 4 times
Download: 1 times
Share this document with a friend
Embed Size (px)
of 37 /37
TRUNNION BALL VALVES
Transcript
WKM Front & Back Cover.CDRPrinted in Canada 08/04 NP-5M
16500 South Main Street Missouri City, Texas 77489 281 499 8511 USA Toll Free 800 323 9160 www.ccvalve.com
C O O P E R C A M E R O N VALVES
USA COOPER CAMERON VALVES Missouri City, Texas Phone: 281-499-8511 Fax: 281-261-3588
COOPER CAMERON VALVES Oklahoma City, Oklahoma Phone: 405-631-1321 Fax: 405-629-0420
UK COOPER CAMERON VALVES Livingston, Scotland Phone: 44-1506-832-000 Fax: 44-1506-432-948
Canada COOPER CAMERON CANADA CORPORATION Calgary, Alberta Phone: 403-398-9930 Fax: 403-398-9936
COOPER CAMERON CANADA CORPORATION Edmonton, Alberta Phone: 780-435-0777 Fax: 780-435-0700
Mexico COOPER CAMERON de MEXICO S.A. de C.V. Mexico City Phone: 52-555-580-0296 Fax: 52-555-395-8669
Other Locations
®DYNASEAL 370 TRUNNION BALL VALVES
TABLE OF CONTENTS
HOW TO ORDER
DYNASEAL 370CT
4 in. - 14 in. x 12 in. (100 mm - 350 mm x 300 mm) ASME/ANSI Class 150 through 300
Features and Benefits 4 & 5
Exploded View 6
DYNASEAL 370D4
2 in. - 6 in. x 4 in. (50 mm - 150 mm x 100 mm) ASME/ANSI Class 150 through 2500
2 1/16 in., 3 1/8 in. & 4 1/16 in. (52 mm, 80 mm & 103 mm) 5000# MOP
Features and Benefits 12 & 13
Exploded View 14
Dimensions 16, 17, 18, 19, 20 & 21
6 in. - 8 in. x 6 in. (150 mm - 200 mm x 150 mm) ASME/ANSI Class 150 and 300
Features and Benefits 22 & 23
Exploded View 24
Trims 25
6 in. - 14 in. x 12 in. (150 mm - 350 mm x 300 mm) ASME/ANSI Class 600 and 900
6 in. - 8 in. x 6 in. (150 mm - 200 mm x 150 mm) ASME/ANSI Class 1500
7 1/16 in. x 6 in. (179 mm x 150 mm) 5000# MOP
Exploded View 26
TERMS AND CONDITIONS 32 & 33
TRADEMARK INFORMATION 34
HOW TO ORDER
2 D4 600 RF x RF 21 Y F F 21 BS
Size Valve Pressure End Body Seat Seal Fire Internal Actuation inches Model Class Connections Group Group Group tested group
370CT
Wrench WR
Carbon Steel 21
Carbon Steel Low Temp NACE 37
Fire Tested F
Nylon 6 Y
Filled PTFE* T
PK P
* These face seals are standard trim for model 370CT valves and are available in ASME/ANSI Class 150 through 600 for model 370D4 valves.
* Ethylene Propylene Rubber.
TRIM APPLICATION INFORMATION
REFER TO TRIM CHARTS IN EACH SECTION:
370CT SERIES: 4 in. (100 mm) through 14 in. x 12 in. (350 mm x 300 mm) ASME/ANSI Class 150 and 300
370D4 SERIES: 2 in. (50 mm) through 6 in. x 4 in. (150 mm x 100 mm) ASME/ANSI Class 150 through 2500 and 2 1/16 in. (52 mm) through 4 1/16 in. (103 mm) 5000# MOP
370D4 SERIES: 6 in. (150 mm) through 14 in. x 12 in. (350 mm x 300 mm) ASME/ANSI Class 150 through 1500 and 7 1/16 in. x 6 in. (179 mm x 150 mm) 5000# MOP
The trim charts provide more specific application details including availability of fire tested materials.
Please contact factory personnel for information concerning availability of trims other than those listed or for any additional information concerning the choice or guidance for application of the trims listed.
The chart above identifies in general terms each of the standard W-K-M trims and where those trims may be used.
The information on this page is general and was created to be used by people who have some technical knowledge of materials and are familiar with the proper applications of materials.
This information is based on our experience and is believed to be reliable, however, information on this page is to be used at your own discretion and risk.
NOTES
VALVES ARE PRICED “BARE STEM” AVAILABLE OPTIONS ARE:
• Wrench operation - Wrenches and multi-position “Wrench Heads”* must be ordered separately. Wrenches are shipped separately with valves but “Wrench Heads”* are installed on the valves.
• Multi-position Wrench Heads* are standard on ASME/ANSI Class 1500, 2500 and 5000# MOP valves.
• Multi- position Wrench Heads* are available as options on 4 in. (100 mm) size for other pressure classes.
• Valves ordered with worm gears (WG) are shipped with gears installed, but handwheels are not installed. (Shipped separately).
• Valves ordered less gear (LG) with gear mounting plate installed (for actuation by others).
• 4 in. (100 mm) D4 ASME/ANSI Class 600 & 900 valves ordered for automation by others (LG) requires a special “actuator” flange at additional cost.
• Locking devices are standard on wrench operated 2 in. and 4 in. (50 mm and 100 mm) bore sizes, D4 Ball Valves, Class 150 through 900.
* Pipe for multi-position Wrench Heads is not supplied with the valve
®DYNASEAL 370 TRUNNION BALL VALVES®DYNASEAL 370 TRUNNION BALL VALVES
References in this catalog to registered trademarks or product designations, which are owned by Cooper Cameron Corporation are as follows:
®Cameron ®Demco
®DynaCentric ®DynaSeal
®Foster ®NAVCO
®Nutron ®Orbit
®Pow-R-Seal ®Saf-T-Seal
References in this catalog to registered trademarks or product designations, which are not owned by Cooper Cameron Corporation are as follows:
Trademark Owner Common Name Comparable CCV Abbreviated Name (in Trim Charts)
Viton Dupont Dow Elastomers L.L.C. Fluoroelastomer FKM
Aflas Asahi Glass Company TFE Propylene FXM
PEEK Victrex PLC Corp United Kingdom Polyetheretherketone PK
Teflon E.I. Dupont De Nemours & Co. Poly Tetra Fluoro Ethylene PTFE
17-4PH Armco Advanced Materials Corp. 17-4PH Stainless Steel Type 630
Electroless Nickel Plating ENP
®DYNASEAL 370CT TRUNNION BALL VALVES
®W-K-M DynaSeal 370CT Series Trunnion Ball Valve is engineered and designed for heavy duty performance. Used in many general purpose petroleum and chemical process applications; also specified for more demanding applications
Seat is set into deep groove in it’s steel retainer, protected from erosion and foreign materials.
Adjustable stem packing.
Stem is positively retained, cannot be removed with valve in service.
Ball is trunnion mounted for low-torque operation.
Pressure-actuated seats provide positive sealing.
for any delays, loss of use or for other direct,
indirect, incidental or consequential damages
incurred by reason of any such judgment. Seller
does not warrant that such material or
apparatus (a) will not infringe any such patent
when not manufactured by or for Seller or when
specially made in whole or in part to the Buyer's
design specification and such infringement arises
from the inclusion of such specified design or (b),
if used or sold in combination with other
material or apparatus, or if used in the practice
of a process, will not, as a result of such
combination or use, infringe any patent covering
such combination or process; and Seller shall not
be liable for and does not indemnify Buyer for
damages or losses of any nature whatsoever
resulting from actual or alleged patent
infringement arising pursuant to (a) or (b)
above.
11. SELLER'S RIGHT TO MANUFACTURE: Seller in its sole discretion shall have the right
to manufacture the products provided
hereunder as far in advance of its estimated
shipping schedule as it deems appropriate. Seller
expressly reserves the right to change or modify
the design and construction of any product in
due course of Seller's manufacturing procedure
without incurring any obligation or liability to
furnish or install such changes, modifications or
improvements to products previously or
subsequently sold.
12. ENGINEERING AND SERVICE: Upon request, Seller will provide engineering
and/or technical information regarding its
products and their uses and if feasible, will
provide personnel to assist Buyer in effecting
field installations and/or field service. Any such
information, service or assistance so provided,
whether with or without charge, shall be
advisory only. In that regard, neither Seller nor
Buyer assumes any liability for the acts or
omissions of the other party except as may be
provided in these terms.
13. LABOR STANDARDS: Seller hereby certifies that these products were
produced in accordance with all applicable
requirements of Section 6, 7 and 12 of the
Fair Labor Standards Act as amended and of
regulations and orders of the United States
Department of Labor issued under Section 14
thereof.
inspection and acceptance of products must be
made at Seller's plant or other shipping or
receiving point designated by Seller and shall
be conclusive except as regards latent defects.
Buyer's representatives may inspect at the
Seller's plant or shipping point during working
hours prior to shipment in such manner as will
not interfere with operations.
15. DELIVERY AND ACCEPTANCE: Delivery shall be in accordance with the
requirements in the Purchase Contract, provided,
in the event Buyer is unable to accept delivery
upon completion of the manufacture of the
Goods in accordance with such requirements,
Buyer agrees that (i) title and risk of ownership
shall pass to Buyer on date of Seller's invoice and
(ii) Buyer will make payments within thirty days
after date of such invoice. Seller shall retain
custodial risk of loss until delivery is made in
accordance with such requirements.
All prices are F.O.B. Seller's plant or other
designated shipping point.
quotation (if any) or in a written contract which
may exist between Seller and Buyer at the time
of shipment. If Seller's quotation or a written
contract states that all or a portion of freight is
allowed, all prices are F.O.B. Seller's plant or
other designated shipping point, with most
economical surface transportation allowed. If
the quoted or contractual price includes
transportation, Seller reserves the right to
designate the common carrier and to ship in the
manner it deems most economical. Added costs
due to special routing requested by the Buyer
are chargeable to the Buyer. Under no
circumstances is any freight allowance which is
absorbed by Seller to be deducted from the
selling price. If the quoted price or contract
includes transportation, no deduction will be
made in lieu thereof whether Buyer accepts
shipment at plant, warehouse, freight station,
or otherwise supplies its own transportation.
When sales are made from the Seller's
warehouse, Seller reserves the right to charge
either actual or pro-rated freight from Seller's
principle point of manufacture to Seller's
warehouse. Buyer assumes risk of loss upon
delivery to the carrier, regardless of who pays
shipping costs.
shipments so that they will not break, rust or
deteriorate in transit, but does not guarantee
against such damage. Unless requested in
writing by the Buyer, no shipments are insured
by Seller against damage or loss in transit. Seller
will place insurance as nearly as possible in
accordance with Buyer's written instructions but
in such case Seller acts only as agent between
the insurance company and the Buyer and
assumes no liability whatsoever.
damage (obvious or concealed) are Buyer's
responsibility and should be made to the carrier.
All claims regarding shortages must be made
within thirty (30) days from receipt of shipment
and must be accompanied by the packing list(s)
covering the shipment.
bills of lading, or other documents required
by the laws of any country or destination are
not included in quotations or selling prices.
If instructed in writing, Seller will make
arrangements for consular documents and
declarations as agent of the Buyer, but Seller
assumes no liability whatsoever as a result of
making such arrangements. Seller assumes no
responsibility for any fines or other charges
imposed due to errors or incorrect declarations.
CAM/T&C/US/96 REV. 9/03
harmless against any claims, demands or causes
of action for property damage or personal injury
(including death) caused by the negligent act or
omission of any employee, agent or sub-
contractor of Seller and not contributed to by
the negligence of Buyer, its employees, its agents
or any third party. Seller shall not be responsible
for the acts and workmanship of employees,
agents, contractors or subcontractors of Buyer
or any third party, nor for failure or malfunction
of any tools, materials, equipment, products,
supplies, facilities or devices not manufactured
and supplied by Seller. Buyer agrees to hold
Seller harmless from any and all losses, claims,
or damages arising from subsurface damage,
surface damage caused by subsurface damage,
loss of hydrocarbons and from pollution,
regardless of whether such damages, losses or
claims were caused by the negligence or sole
negligence of Seller, it being the intent of the
parties that this indemnity shall apply to
property of Buyer or to that of any third party.
B. LIMITATION OF LIABILITY:
INCIDENTAL DAMAGES, INCLUDING, BUT NOT
LIMITED TO LOSS OF ANTICIPATED PROFITS,
LOSS OF USE OF EQUIPMENT OR OF ANY
INSTALLATION, SYSTEM OR FACILITY INTO
WHICH SELLER'S EQUIPMENT MAY BE LOCATED
OR AT WHICH SELLER, ITS AGENT OR
SUBCONTRACTOR MAY BE PERFORMING WORK.
Seller's total responsibility for any claims,
damages, losses or liabilities arising out of or
related to its performance of this contract or
the products or services covered hereunder shall
not exceed the purchase price.
19. MODIFICATION, RESCISSION & WAIVER: The terms herein may not be modified or
rescinded nor any of its provisions waived unless
such modification, rescission or waiver is in
writing and signed by an authorized employee
of Seller at its office in Houston, Texas.
Failure of Seller to insist in anyone or more
instances upon the performance of any of the
terms and conditions of the contract or the
failure of Seller to exercise any of its rights
hereunder shall not be construed as a waiver
or relinquishment of any such term, condition,
or right hereunder and shall not affect Seller's
right to insist upon strict performance and
compliance with regard to any unexecuted
portions of this contract or future performance
of these terms and conditions.
All orders must be accepted by an authorized
employee of Seller. The rights and duties of the
parties and construction and effect of all
provisions hereof shall be governed by and
construed according to the internal laws of the
State of Texas. Any disputes which arise under
this agreement shall be venued in the District
Court of Harris County, Texas or in the Southern
District of Texas.
4 in. - 14 in. x 12 in. (100 mm - 350 mm x 300 mm)
334 TC1777 08/04 NP-5M
®DYNASEAL 370CT TRUNNION BALL VALVES
DEEP POCKETED SEATS A deep seat pocket encapsulates the two-piece seat assembly which consists of an outer metal seat ring with a TFE insert. An O-Ring energizes the seat face against the ball to ensure ball/seat contact at all pressures.
POSITIVELY RETAINED STEM The stem is held positively in place by means of a steel retention pin which cannot be removed without disassembling the valve.
TRUNNION SUPPORTED BALL ALLOWS LOW TORQUE OPERATION Trunnion ball valves allow easy on-off operation, even at high pressures, since the ball turns on carefully aligned bearings. The ball is fixed in position, but free to turn. Torque is so low that wrench operation of valves through 6 in. (150 mm) port size is practical. When power actuation is desired, much smaller actuators are needed.
ACTUATION-FRIENDLY A variety of actuator types can be easily installed including pneumatic, hydraulic, diaphragm, electro-mechanical and electro-hydraulic. Cooper Cameron Valves can provide a total package of valves and actuators to meet your needs.
The general purpose trunnion ball valve for the petroleum and chemical process industries, its strong suit is low torque block and bleed service.
W-K-M DynaSeal 370 CT ball valves satisfy a wide range of ASME/ANSI and API 6D applications. Available in carbon steel and stainless steel with various trims, they may be specified in sizes from 4 inch to 14 inch (100 mm to 350 mm) and pressure classes of 150 and 300. Engineered for heavy duty, maintenance- free performance. The DynaSeal 370 CT is commonly selected for a number of demanding applications.
FEATURES AND BENEFITS DOUBLE BLOCK & BLEED OPERATION • The pressure-actuated seats and
bleed fittings allow double block and bleed operation
• When used for block and bleed, this feature may permit the valve to take the place of two valves
• It also allows the operator to check up and downstream sealing by installing pressure-releasing tool to bleed the body pressure.
FIRE TESTED FOR SAFETY • All DynaSeal 370CT valves with TFF
and TRF trim are qualified under API standard 6FA and TFF trim is also qualified under API 607 4th Edition
• The deep pocketed seats contribute to its unusually good fire test characteristics
• Should the soft seats be destroyed by fire, the metal shoulder acts as a secondary metal-to-metal seal until maintenance can be performed.
EASY TO MAINTAIN • The valve can be completely
disassembled in the field for replacement of seats or for a complete overhaul
• Seats can be replaced quickly without special tools.
Actuator mounting bracket for 4 in. - 10 in. x 8 in. (100 mm - 250 mm x 200 mm) Valves (Optional)
Actuator mounting bracket for 10 in. - 14 in. x 12 in. (250 mm - 350 mm x 300 mm) Valves (Standard)
®DYNASEAL 370 TRUNNION BALL VALVES TERMS AND CONDITIONS 1. CONTRACT ACCEPTANCE: Any written or oral purchase order received
from Buyer by Cooper Cameron Corporation,
Cameron Division and Cooper Cameron Valves
("Seller”) shall be construed as a written
acceptance of Seller's offer to sell and shall be
filled in accordance with the terms and conditions
of sale set forth herein. SELLER'S ACCEPTANCE OF
THIS ORDER IS EXPRESSLY CONDITIONED ON
BUYER'S ASSENT TO THE TERMS CONTAINED
HEREIN. The terms and conditions of Seller's
proposal (if any) and acknowledgement shall
prevail over any conflicting or different terms in
Buyer's order unless Buyer notifies Seller in writing
of its objections thereto within fifteen (15) days
from receipt of Seller's acknowledgement. Buyer's
standard terms of purchase will not be considered
a counteroffer to Seller's terms and conditions of
sale. The failure of Seller to object to any provision
in conflict herewith whether contained on Buyer's
purchase order or otherwise shall not be
construed as a waiver of the provisions hereof
nor as an acceptance thereof.
2. QUOTATIONS AND PRICES: All quotations are made for prompt acceptance
and any terms quoted therein are subject to
change without notice after thirty (30) days from
the date quoted unless specifically stated
otherwise on the quotation. Any product, service
capability or manufacturing capability which may
be available at the time a quotation is made is
subject to prior sale. Prices quoted are valid for
thirty (30) days unless specifically stated otherwise
on the quotation and are subject to change
without notice. The price in effect at the time of
shipment including any escalation formula will
apply, unless a valid quotation or written
agreement to the contrary exists between Buyer
and Seller. All prices shown are in U.S. dollars
and are F.O.B. Seller‘s shipping point.
Any documentation pertaining to traceability
requirements for raw materials or products or
documentation required for any routine or
special processes must be identified by the Buyer
at the time of quotation (if any) or at the time of
order placement.
3. TAXES: Any tax or other charge imposed by law on the
sale or production of goods or the performance
of services shall be paid by the Buyer, unless the
law specifically provides that such payment must
be made by Seller, in which case Buyer shall
reimburse Seller for such payment as part of the
purchase price. Custom duties, consular fees,
insurance charges and other comparable charges
will be borne by Buyer.
4. SHIPPING SCHEDULE AND DELIVERY: Shipment schedules are given as accurately as
conditions permit and every effort will be made
to make shipments as scheduled. Seller will not
be responsible for deviations in meeting shipping
schedules nor for any losses or damages to Buyer
(or any third party) occasioned by deviations in
the shipping schedule, whether due to Acts of
God, orders bearing priority ratings established
pursuant to law, differences with workmen, local
labor shortages, fire, flood, shortages or failure
of raw materials, supplies, fuel, power or
transportation, breakdown of equipment or any
other causes beyond Seller's reasonable control,
whether of similar or dissimilar nature than those
enumerated. Seller shall have additional time
within which to perform as may be reasonably
necessary under the circumstances and shall have
the right to apportion its production among its
customers in such a manner as it may consider to
be equitable.
thereof as Seller deems necessary. In no event
shall Seller be liable for any consequential
damages for labor resulting from failure or
delay in shipment. If Buyer requires drawings,
procedures, standards or similar material for
approval, shipping schedules will be calculated
from the time such approvals are received by
Seller, since shipping schedules are based on
Seller having all required information and a
firm order from Buyer which is enterable into
production. Any hold points, witness points or
the need for inspection by Buyer's represent-
atives must be identified by Buyer at the time
of quotation (if any) and/or order placement in
order that the effect on the prices or shipping
schedules (if any) can be taken into account.
Additional inspection or testing required by
Buyer which affects normal production
sequence will be considered as extending
the shipping dates accordingly.
5. MINIMUM BILLING: Seller reserves the right to impose a minimum
billing charge on all sales, change orders or
order supplements.
6. TERMS OF PAYMENT: Terms of payment for all materials and service
are 30 days from invoice date, at net price,
provided satisfactory credit has been established.
All unpaid invoices are subject to the maximum
legal interest rate per annum commencing with
the due date.
7. CANCELLATIONS AND RETURNS: Purchase orders once placed by Buyer and
accepted by Seller can be canceled only with
Seller's written consent and upon terms which
will save Seller from loss. No products may be
returned for credit or adjustment without
written permission from Seller's office
authorized to issue such permission.
8. WARRANTIES: All products of Seller's manufacture are
warranted against defects of material and
workmanship for a period of twelve (12)
months from the date of installation or
eighteen (18) months from date of shipment,
whichever period first expires, when such
products are used in the service and within
the pressure range for which they were
manufactured. In the case of products or parts
not wholly of Seller's manufacture, Seller's
liability shall be limited to the extent of its
recovery from the manufacturer of such
products or parts under its liability to Seller.
Any repair work performed by Seller is warranted
for one year from completion of such repairs and
applies only to work performed.
If, within these specified periods, Seller receives
notice from Buyer of any alleged defect in or
nonconformance of any product or repair and if,
in the Seller's sole judgment, the product or repair
does not conform or is found to be defective in
material or workmanship, then, Buyer shall, at
Seller's request, return the part or product F.O.B.
to Seller's designated plant or service location.
Seller has no liability for removal or reinstallation
of products or equipment from below the surface
of the water. Seller, at its option and expense,
shall repair or replace the defective part or product,
or repay to Buyer the full price paid by Buyer for
such defective part, repair or product. Any
repayment of purchase price shall be without
interest.
caused by Seller's negligence, shall be limited to
such repair, replacement or refund, and shall not
include claims for labor costs, expenses of Buyer
resulting from such defects, recovery under general
tort law or strict liability or for damages resulting
from delays, loss of use, or other direct, indirect,
incidental or consequential damages of any kind.
Seller will not be responsible for failures of products
which have been in any way tampered with or
altered by anyone other than an authorized
representative of Seller, failures due to lack of
compliance with recommended maintenance
procedures or products which have been repaired
or altered in such a way (in Seller's judgment) as to
affect the products adversely. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE
WARRANTY OF MERCHANTABILITY AND FITNESS
FOR PARTICULAR PURPOSE WHICH EXCEED
THE FOREGOING WARRANTY.
9. NUCLEAR SALES: The products sold hereunder are not designed or
manufactured for use in or with any atomic
installation or activity. If the Buyer or ultimate
user of these products intends to use them in such
an installation or activity, Seller's Nuclear Terms of
Sale shall be part of and control this contract.
Seller will furnish Buyer with a copy of its Nuclear
Terms of Sale upon request.
10. PATENT INFRINGEMENT: Seller warrants that the use or sale of material
or apparatus sold or rented by it to Buyer
hereunder will not infringe United States' patents
of others covering such material or apparatus by
itself, and hereby agrees to indemnify Buyer against
judgment for damages for such infringement of
any such patent, provided that Buyer shall, upon
receipt of any claim for infringement of any such
patent or threat of suit for such infringement or
upon the filing of any suit for infringement, which-
ever comes first, promptly notify Seller in writing
and afford Seller full opportunity, at its option and
its own expense, to answer such claim or threat
of suit, assume the control of the defense of said
suit, and settle or compromise same in any way
Seller sees fit. Other than court-awarded
judgments as aforesaid Seller shall not be liable
532 TC1777 08/04 NP-5M
®DYNASEAL 370CT TRUNNION BALL VALVES
CLASS 150 AND 300 4 in. - 14 in. x 12 in. (100 mm - 350 mm x 300 mm)
DynaSeal 370CT ball valves conform to the following design and testing standards:
• API 6D
• MSS-SP-6 (Standard Finishes for Pipe Flanges)
• MSS-SP-25 (Standard Marking System for Valves)
• MSS-SP-55 (Quality Standards for Steel Castings)
• API 6FA (Fire Test Specification)
In addition DynaSeal 370CT ball valves can be supplied to comply with these standards:
• ASME/ANSI B31.1 (Power Piping)
• ASME/ANSI B31.3 (Chemical Plant and Petroleum Refinery Piping)
• MSS-SP-61 (Pressure Testing of Steel Valves)
• ASME/ANSI B16.104 (Valve Seat Leakage)
• NACE MR0175 (Rev. 2002)
SIZE CLASS in. (mm) 150 300
4 (100) • •
6 (150) • •
8 (200) • •
10 (250) • •
12 (300) • •
Trunnion Bearing
Trunnion Block
Seat Insert
CLASS 150 THROUGH 2500 & 5000# MOP
The above values are new valve torque values, where P is the maximum operating pressure (psig) of the valve.
The above torque values do not contain service factors. Soaking effects and/or particle matter in the valve may cause
an increase in the torque.
For interpolated torque calculations, use the torque expressions corresponding to the applicable pressure range only.
For example, a pressure of 1000 psig uses the torque equations in the 741-1480 psig pressure range only.
The reseat torque is taken as 0.75 times the break torque. For power operation, multiply all of the above values by a
factor of 1.25 or customer specified factor whichever is larger.
For operating temperatures between -20°F to -50°F (-29°C to -46°C), multiply these values by 1.20.
Actuator selection should be made based on customer experience and appropriate service factors.
VALVE PORT PRESSURE TORQUE EXPRESSIONS BREAK RUN RESEAT SIZE (P) BREAK RUN TORQUE TORQUE TORQUE
TORQUE TORQUE @ MAX. P @ MAX. P @ MAX. P in. (mm) (psig) (in-lbs) (in-lbs) (in-lbs) (in-lbs) (in-lbs)
2 (50) 0 - 285 213 + (0.24 x P) 107 + (0.12 x P) 281 141 211
286 - 740 133 + (0.52 x P) 71 + (0.25 x P) 518 256 388
741 - 1480 52 + (0.63 x P) 20 + (0.32 x P) 984 494 738
1481 - 2220 38 + (0.64 x P) 66 + (0.29 x P) 1459 710 1094
2221 - 3705 106 + (0.61 x P) 23 + (0.31 x P) 2366 1172 1775
3706 - 6170 144 + (0.60 x P) 99 + (0.29 x P) 3846 1888 2885
3 (80) 0 - 285 383 + (0.44 x P) 191 + (0.22 x P) 508 254 381
286 - 740 109 + (1.40 x P) 52 + (0.71 x P) 1145 577 859
741 - 1480 117 + (1.39 x P) 60 + (0.70 x P) 2174 1096 1631
1481 - 2220 73 + (1.42 x P) 16 + (0.73 x P) 3225 1637 2419
2221 - 3705 672 + (1.15 x P) 417 + (0.55 x P) 4933 2455 3700
3706 - 6170 375 + (1.23 x P) 122 + (0.63 x P) 7964 4009 5973
4 (100) 0 - 285 822 + (0.94 x P) 411 + (0.47 x P) 1090 545 817
286 - 740 365 + (2.54 x P) 183 + (1.27 x P) 2245 1123 1683
741 - 1480 364 + (2.54 x P) 176 + (1.28 x P) 4123 2070 3092
1481 - 2220 363 + (2.54 x P) 191 + (1.27 x P) 6002 3010 4501
2221 - 3705 2827 + (1.43 x P) 1412 + (0.72 x P) 8125 4080 6094
3706 - 6170 455 + (2.07 x P) 301 + (1.02 x P) 13227 6594 9920
6 (150) 0 - 285 1661 + (7.50 x P) 1026 + (2.18 x P) 3799 1647 2849
286 - 740 2817 + (3.44 x P) 1434 + (0.75 x P) 5363 1989 4022
741 - 1480 1659 + (5.00 x P) 1027 + (1.30 x P) 9059 2951 6794
1481 - 2220 26 + (6.10 x P) 94 + (2.00 x P) 13568 4534 10176
2221 - 3705 2256 + (5.53 x P) 92 + (2.00 x P) 22745 7502 17058
3706 - 5000 7700 + (4.06 x P) 1536 + (1.61 x P) 28000 9586 21000
8 (200) 0 - 285 2899 + (13.92 x P) 1834 + (3.13 x P) 6866 2726 5150
286 - 740 3907 + (10.35 x P) 2287 + (1.54 x P) 11566 3427 8675
741 - 1480 5195 + (8.60 x P) 2221 + (1.63 x P) 17923 4633 13442
1481 - 2220 4521 + (9.05 x P) 2324 + (1.56 x P) 24612 5787 18459
10 (250) 0 - 285 2916 + (26.43 x P) 2041 + (12.28 x P) 10449 5541 7836
286 - 740 6795 + (12.78 x P) 5131 + (1.44 x P) 16252 6197 12189
741 - 1480 7636 + (11.63 x P) 5139 + (1.43 x P) 24848 7255 18636
1481 - 2220 2872 + (14.84 x P) 5820 + (0.97 x P) 35817 7973 26863
12 (300) 0 - 285 5728 + (26.16 x P) 4421 + (5.20 x P) 13184 5903 9888
286 - 740 8827 + (15.24 x P) 5710 + (0.68 x P) 20105 6213 15078
741 - 1480 8836 + (15.21 x P) 5185 + (1.39 x P) 31347 7242 23510
1481 - 2220 14939 + (11.08 x P) 5466 + (1.20 x P) 39537 8130 29652
STEM TORQUE
BODY GROUP TRIM NUMBER
CARBON STEEL CARBON STEEL STAINLESS STEEL PART CARBON STEEL (NACE) LOW TEMP (NACE) (NACE)
21 24 37 23
Body A216 Gr. WCC/ A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Tailpiece A216 Gr. WCC/ A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Trunnion Blocks Carbon Steel Carbon Steel Carbon Steel 316 SS
Studs A193 Gr. B7 A193 Gr. B7 A320 Gr. L7M A193 Gr. B7 Zinc Plate
Nuts A194 Gr. 2H A194 Gr. 2H A320 Gr. 7ML A194 Gr. 2H Zinc Plate
Grease Fitting Carbon Steel Stainless Steel Stainless Steel Stainless Steel
Bonnet Cap A216 Gr. WCC A216 Gr. WCC A351 Gr. CF8M A351 Gr. CF8M
Grounding Spring Stainless Steel Stainless Steel Stainless Steel Stainless Steel
PACKING ADJUST
Cap Screw 4 in. to 8 in. x 6 in. Alloy Steel Alloy Steel 303 SS Alloy Steel (100 mm to 200 mm x 150 mm)
Stud Nut 8 in. to 14 in. x 12 in. A193 Gr. B7 A193 Gr. B7 A320 Gr. 7ML A193 Gr. B7 Zinc Plate(200 mm to 350 mm x 300 mm)
Stud 8 in. to 14 in. x 12 in. A194 Gr. 2H A194 Gr. 2H A194 Gr. L7M A194 Gr. 2H Zinc Plate (200 mm to 350 mm x 300 mm)
Ball A105/WCC CS ENP A105/WCC CS ENP A105/WCC CS ENP 316 SS/CF8M
Stem Carbon Steel ENP Carbon Steel ENP 4130-4140 ENP 316 SS
Stem Retainer Pin Carbon Steel Carbon Steel 316 SS 316 SS
Seat Rings Carbon Steel Carbon Steel Carbon Steel 316 SS
Pipe Plug Carbon Steel Stainless Steel Stainless Steel Stainless Steel
Compression Ring 304 SS 304 SS 304 SS 304 SS
Trunnion Bearings CS/Filled PTFE CS/Filled PTFE CS/Filled PTFE SS/Filled PTFE
SEAL GROUP TRIM CODE
PART TFF FIRE TESTED TRF FIRE TESTED
Temperature Limits -20°F to 350°F (-29°C to 177°C) -50°F to 250°F (-46°C to 121°C)
Seat Inserts Filled PTFE Filled PTFE
Seat O-Rings High Fluorine FKM HNBR
Stem Gasket Filled PTFE Filled PTFE
Stem Packing (Graphite) Filled PTFE (Graphite) Filled PTFE
Body/Tailpiece Gasket Filled PTFE Filled PTFE
INTERNAL GROUP TRIM NUMBER
Note: Trims 21, 23 and 24 are suitable for temperatures from -20°F to 350°F (-29°C to 177°C). Trim 37 is suitable for temperatures from -50°F to 350°F (-46°C to 177°C).
NACE indicates compliance with NACE MR0175. (Rev. 2002)
®DYNASEAL 370D4 TRUNNION BALL VALVES
FLOW CHARACTERISTICS (C )*V
VALVE PORT SIZE VALVE PRESSURE CLASS in. (mm) 150 300 600 900 1500 (5000# MOP) 2500
2 x 2 (50 x 50) 473 429 369 328 328 207
3 x 2 (80 x 50) - - 136 136 - -
3 x 3 (80 x 80) 1244 1055 940 908 818 490
4 x 3 (100 x 80) - - 407 406 - -
4 x 4 (100 x 100) 2492 2158 1813 1762 1598 1014
6 x 4 (150 x 100) 432 432 552 551 593 414
6 x 6 (150 x 150) 5468 5403 4590 4394 4112 -
8 x 6 (200 x 150) 1294 1293 1642 1637 1652 -
8 x 8 (200 x 200) - - 8971 8494 - -
10 x 8 (250 x 200) - - 3578 3569 - -
10 x 10 (250 x 250) - - 14352 13911 - -
12 x 10 (300 x 250) - - 6505 6454 - -
12 x 12 (300 x 300) - - 22772 21221 - -
14 x 12 (350 x 300) - - 10592 10490 - -
CLASS 150 THROUGH 2500 & 5000# MOP
WEIGHTS lb. (kg) - WORM GEAR ACTUATOR ONLY
VALVE PORT SIZE VALVE PRESSURE CLASS in. (mm) 150 300 600 900 1500 (5000# MOP) 2500
2 (50) 13.5 (6.1) 13.5 (6.1) 13.5 (6.1) 13.5 (6.1) 27.5 (12.5) 27.5 (12.5)
3 (80) 13.5 (6.1) 13.5 (6.1) 13.5 (6.1) 27.5 (12.5) 32.0 (14.5) 47.5 (21.5)
4 (100) 25.6 (11.6) 27.5 (12.5) 27.5 (12.5) 32.0 (14.5) 47.5 (21.5) 69.5 (31.5)
6 (150) 36.0 (16.3) 36.0 (16.3) 40.0 (18.1) 79.5 (36.1) 79.5 (36.1) -
8 (200) - - 81.0 (36.7) 82.5 (37.4) - -
10 (250) - - 82.0 (37.2) 110.0 (49.9) - -
12 (300) - - 110.0 (49.9) 163.5 (74.2) - -
WEIGHTS lb. (kg) - VALVE ONLY - BARE STEM
VALVE PORT SIZE VALVE PRESSURE CLASS in. (mm) 150 300 600 900 1500 (5000# MOP) 2500
2 x 2 (50 x 50) 33 (15.0) 45 (20.4) 65 (29.5) 94 (42.6) 120 (54.4) 170 (77.1)
3 x 2 (80 x 50) - - 82 (37.2) 107 (48.5) - -
3 x 3 (80 x 80) 60 (27.2) 78 (35.4) 128 (58.1) 175 (79.4) 215 (97.5) 410 (186.0)
4 x 3 (100 x 80) - - 175 (79.4) 240 (108.9) - -
4 x 4 (100 x 100) 105 (47.6) 145 (65.8) 200 (90.7) 276 (125.2) 400 (181.4) 670 (303.9)
6 x 4 (150 x 100) 155 (70.3) 200 (90.7) 275 (124.7) 366 (166.0) 640 (290.3) 1188 (538.9)
6 x 6 (150 x 150) 234 (106.1) 285 (129.3) 500 (226.8) 650 (294.8) 941 (426.8) -
8 x 6 (200 x 150) 294 (133.4) 361 (163.7) 575 (260.8) 748 (339.3) 1220 (553.4) -
8 x 8 (200 x 200) - - 800 (362.9) 1010 (458.1) - -
10 x 8 (250 x 200) - - 920 (417.3) 1162 (527.1) - -
10 x 10 (250 x 250) - - 1270 (576.1) 1580 (716.7) - -
12 x 10 (300 x 250) - - 1460 (662.2) 1817 (824.2) - -
12 x 12 (300 x 300) - - 1880 (852.8) 2450 (1111.3) - -
14 x 12 (350 x 300) - - 2160 (979.8) 2818 (1278.2) - -
* Flow of water in U.S. gal/min /1 psi pressure drop across a fully open valve.
Note: Weights shown are for worm gear actuator, handwheel and mounting hardware.
CLASS 150 AND 300 4 in. - 14 in. x 12 in. (100 mm - 350 mm x 300 mm) MATERIALS LIST
730 TC1777 08/04 NP-5M
®DYNASEAL 370CT TRUNNION BALL VALVES
CLASS 150 AND 300 4 in. - 14 in. x 12 in. (100 mm - 350 mm x 300 mm)
WRENCH OPERATED VALVES WORM GEAR OPERATED VALVES
Note: Flange holes are tapped 3/4-10 NC on 6 inch (150 mm) Class 150 Short Pattern (Both Ends), Full Port Valves.
3/4-10 NC on 6 inch (150 mm), Class 150 Long Pattern (Body Ends only), Full Port Valves.
3/4-10 NC on 8 inch (200 mm), Class 150 Short Pattern (Tail Piece End only), Reduced Port Valves.
1-8 NC on 10 inch (250 mm) 300 Short Pattern Both Ends.
DIA
BC
D
E
M
K
DIA
MOUNTING BRACKET FOR 4 in. THROUGH 10 in. x 8 in. VALVES (100 mm THROUGH 250 mm x 200 mm VALVES)
V
MOUNTING BRACKET FOR 10 in. (250 mm) VALVES AND LARGER
T
S
V
®DYNASEAL 370D4 TRUNNION BALL VALVES
REDUCED PORT DIMENSIONS CLASS 150
A B BB H J K L M N P Q R T U V W X
SIZE in. RF RJ
8 x 6 18.00 18.50 6.00 8.00 7.06 9.41 11.16 1.503 7.50 9.50 0.375 0.56-(8) 0.88 11.16 12.85 3.39 8.83 12.00
SIZE mm
200 x 150 457 470 152 203 179 239 283 38.18 191 241 9.53 - 22 283 326 86 224 305
CLASS 300
CLASS 600
A B BB H J K L M N P Q R T U V W X
SIZE in. RF RJ
8 x 6 26.00 26.12 6.00 8.00 7.12 9.41 11.25 1.503 7.50 9.50 0.375 0.56-(8) 0.88 11.16 12.85 3.39 12.26 20.00
10 x 8 31.00 31.12 8.00 10.00 9.25 11.75 14.81 1.685 8.00 9.25 0.375 0.66-(8) 1.05 13.91 16.31 5.12 15.25 24.00
12 x 10 33.00 33.12 10.00 12.00 11.38 13.69 16.93 2.003 7.50 9.50 0.500 0.56-(8) 1.16 15.86 18.25 5.12 14.85 28.00
14 x 12 35.00 35.12 12.00 14.00 13.93 16.13 19.50 2.560 10.25 12.50 0.625 0.69-(8) 1.28 18.30 22.24 8.31 17.61 24.00
SIZE mm
200 x 150 660 663 152 203 181 239 286 38.18 191 241 9.53 - 22 283 326 86 311 508
250 x 200 787 790 203 254 235 298 376 42.80 203 235 9.53 - 27 353 414 130 387 610
300 x 250 838 841 254 305 289 348 430 50.88 191 241 12.70 - 29 403 464 130 377 711
350 x 300 889 892 305 356 354 410 495 65.02 260 318 15.88 - 33 465 565 211 447 610
A B BB H J K L M N P Q R T U V W X
SIZE in. RF RJ
8 x 6 19.75 20.38 6.00 8.00 7.06 9.41 11.16 1.503 7.50 9.50 0.375 0.56-(8) 0.88 11.16 12.85 3.39 8.83 12.00
SIZE mm
200 x 150 502 518 152 203 179 239 283 38.18 191 241 9.53 - 22 283 326 86 224 305
A B BB H J K L M N P Q R T U V W XSIZE in. RF RJ
8 x 6 29.00 29.12 6.00 8.00 8.06 10.09 13.12 1.685 8.00 9.25 0.375 0.66-(8) 1.05 12.25 14.65 5.12 15.25 20.00
10 x 8 33.00 33.12 8.00 10.00 10.31 12.31 15.31 2.003 7.50 9.50 0.500 0.56-(8) 1.16 14.48 16.88 5.12 14.85 28.00
12 x 10 38.00 38.12 10.00 12.00 12.25 14.47 21.56 2.560 10.25 12.50 0.625 0.69-(8) 1.28 16.64 20.58 8.31 17.61 24.00
14 x 12 40.50 40.88 12.00 14.00 14.88 17.78 19.50 2.745 10.25 12.50 0.625 0.69-(8) 1.63 19.95 23.89 10.36 19.69 20.00
SIZE mm
200 x 150 737 740 152 203 205 256 333 42.80 203 235 9.53 - 27 311 372 130 387 508
250 x 200 838 841 203 254 262 313 389 50.88 191 241 12.70 - 29 368 429 130 377 711
300 x 250 965 968 254 305 311 368 548 65.02 260 318 15.88 - 33 423 523 211 447 610
350 x 300 1029 1038 305 356 378 452 495 69.72 260 318 15.88 - 41 507 607 263 500 508
A B BB H J K L M N P Q R T U V W XSIZE in. RF RJ
8 x 6 32.75 33.12 6.00 7.63 10.25 11.53 15.15 2.003 8.00 9.75 0.500 0.78-(4) 1.50 13.70 16.10 5.12 15.25 20.00
SIZE mm
200 x 150 832 841 152 194 260 293 385 50.88 203 248 12.70 - 38 348 409 130 387 508
CLASS 150 THROUGH 1500 & 5000# MOP 8 in. x 6 in. (200 mm x 150 mm) THROUGH 14 in. x 12 in. (350 mm x 300 mm)
K
H
J
R
A
CLASS 900
REDUCED PORT DIMENSIONS
A* Class SIZE 150 RF 300 RF 300 B C D E F G H J K L M N P R S T U V W in. BWLong Short Long Short
10.50 - - 4.00 6.00 6.45 8.63 9.88 36.00 7.56 1.250 8.00 2.80 7.88 0.250 10.84 9.15 - - 0.56 2.44 4.921 6 x 4 N/A N/A
- 15.88 15.88 4.00 6.00 6.45 8.63 9.88 36.00 7.56 1.250 10.00 2.80 8.12 0.250 10.84 9.15 - - 0.56 2.44 4.921
18.00 - 16.50 16.50 6.00 8.00 8.20 11.38 12.63 48.00 9.44 1.500 14.00 2.80 10.95 0.375 12.72 11.03 - - 0.56 2.44 4.921 8 x 6 N/A
- 11.50 - - 6.00 8.00 8.20 11.38 12.63 48.00 9.44 1.500 10.00 2.80 8.12 0.375 12.72 11.03 - - 0.56 2.44 4.921
21.00 - - 8.00 10.00 10.10 16.38 - - 13.50 2.375 20.00 4.11 13.64 0.625 17.34 15.39 - - 0.68 4.00 5.512 10 x 8 N/A N/A
- 22.38 22.00 8.00 10.00 10.10 16.38 - - 13.50 2.375 20.00 4.11 13.64 0.625 17.34 15.39 - - 0.68 4.00 5.512
24.00 - - 10.00 12.00 11.78 18.50 - - 15.12 2.938 20.00 5.12 15.25 0.750 19.70 17.30 7.75 5.75 0.75 3.00 - 12 x 10 N/A N/A
- 25.50 25.50 10.00 12.00 11.78 18.50 - - 15.12 2.938 20.00 8.31 17.61 0.750 21.23 17.30 7.75 5.75 0.75 3.00 -
27.00 - - 12.00 14.00 13.97 20.13 - - 16.38 2.938 20.00 5.12 15.25 0.750 20.95 18.55 7.75 5.75 0.75 3.00 - 14 x 12 N/A N/A
- 30.00 30.00 12.00 14.00 13.97 20.13 - - 16.38 2.938 20.00 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00 -
A* Class SIZE 150 RF 300 RF 300 B C D E F G H J K L M N P R S T U V W mm Long Short Long Short BW
267 - - 102 152 164 219 251 914 192 31.75 203 71 200 6.35 275 232 - - 14 62 124.99 150 x 100 N/A N/A
- 403 403 102 152 164 219 251 914 192 31.75 254 71 206 6.35 275 232 - - 14 62 124.99
457 - 419 419 152 203 208 289 321 1219 240 38.10 356 71 278 9.53 323 280 - - 14 62 124.99 200 x 150 N/A
- 292 - - 152 203 208 289 321 1219 240 38.10 254 71 206 9.53 323 280 - - 14 62 124.99
533 - - 203 254 257 416 - - 343 60.33 508 104 346 15.88 440 391 - - 17 102 140.00 250 x 200 N/A N/A
- 568 559 203 254 257 416 - - 343 60.33 508 104 346 15.88 440 391 - - 17 102 140.00
610 - - 254 305 299 470 - - 384 74.63 508 130 387 19.05 500 439 197 146 19 76 - 300 x 250 N/A N/A
- 648 635 254 305 299 470 - - 384 74.63 508 211 447 19.05 539 439 197 146 19 76 -
686 - - 305 356 355 511 - - 416 74.63 508 130 387 19.05 532 471 197 146 19 76 - 350 x 300 N/A N/A
- 762 762 305 356 355 511 - - 416 74.63 508 211 447 19.05 571 471 197 146 19 76 -
in.
mm
* Centerline-to-face dimension is half of dimension A, except: 4 in. (100 mm) ASME/ANSI Class 150 Full Port - stem is offset 1/2 in. (12.7 mm) towards body end and 6 in. (150 mm) ASME/ANSI Class 150 Full Port Long Pattern - stem is offset 2 1/2 in. (63.5 mm) towards body end.
FULL PORT DIMENSIONS
A* Class SIZE 150 RF 300 RF 300 B C D E F G H J K L M N P R S T U V W in. BWLong Short Long Short
9.00 - - 4.00 4.00 6.47 8.63 9.88 36.00 7.56 1.250 8.00 2.80 7.88 0.250 10.84 9.15 - - 0.56 2.44 4.921 4 N/A N/A
- 12.00 12.00 4.00 4.00 6.47 8.63 9.88 36.00 7.56 1.250 10.00 2.80 8.12 0.250 10.84 9.15 - - 0.56 2.44 4.921
15.50 - 15.88 15.88 6.00 6.00 8.20 11.38 12.63 48.00 9.44 1.500 14.00 2.80 10.95 0.375 12.72 11.03 - - 0.56 2.44 4.921 6 N/A
- 10.50 - - 6.00 6.00 8.20 11.38 12.63 48.00 9.44 1.500 10.00 2.80 8.12 0.375 12.72 11.03 - - 0.56 2.44 4.921
18.00 - 16.50 - 8.00 8.00 9.95 16.38 - - 13.50 2.375 16.00 4.11 11.11 0.625 17.34 15.39 - - 0.68 4.00 5.512 8 N/A
- 19.75 - 16.50 8.00 8.00 9.97 16.38 - - 13.50 2.375 18.00 4.11 13.64 0.625 17.34 15.39 - - 0.68 4.00 5.512
21.00 - - - 10.00 10.00 11.63 18.50 - - 15.12 2.938 20.00 5.12 15.25 0.750 19.70 17.30 7.75 5.75 0.75 3.00 -
10 - N/A 22.38 - 22.00 10.00 10.00 11.65 18.50 - - 15.12 2.938 20.00 8.31 17.61 0.750 21.23 17.30 7.75 5.75 0.75 3.00 -
- - 18.00 - 10.00 10.00 11.65 18.50 - - 15.12 2.938 16.00 8.31 15.32 0.750 21.23 17.30 7.75 5.75 0.75 3.00 -
24.00 - - 12.00 12.00 13.97 20.13 - - 16.38 2.938 20.00 5.12 15.25 0.750 20.95 18.55 7.75 5.75 0.75 3.00 - 12 N/A N/A
- 25.50 25.00 12.00 12.00 13.97 20.13 - - 16.38 2.938 20.00 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00 -
A* Class SIZE 150 RF 300 RF 300 B C D E F G H J K L M N P R S T U V W mm BWLong Short Long Short
229 - - 102 102 164 219 251 914 192 31.75 203 71 200 6.35 275 232 - - 14 62 124.99 100 N/A N/A
- 305 305 102 102 164 219 251 914 192 31.75 254 71 206 6.35 275 232 - - 14 62 124.99
394 - 403 403 152 152 208 289 321 1219 240 38.10 356 71 278 9.53 323 280 - - 14 62 124.99 150 N/A
- 267 - - 152 152 208 289 321 1219 240 38.10 254 71 206 9.53 323 280 - - 14 62 124.99
457 - 419 - 203 203 253 416 - - 343 60.33 406 104 282 15.88 440 391 - - 17 102 140.00 200 N/A
- 502 - 419 203 203 253 416 - - 343 60.33 457 104 346 15.88 440 391 - - 17 102 140.00
533 - - - 254 254 295 470 - - 384 74.63 508 130 387 19.05 500 439 197 146 19 76 -
250 - N/A 568 - 559 254 254 296 470 - - 384 74.63 508 211 447 19.05 539 439 197 146 19 76 -
- - 457 - 254 254 296 470 - - 384 74.63 406 211 389 19.05 539 439 197 146 19 76 -
610 - - 305 305 355 511 - - 416 74.63 508 130 387 19.05 532 471 197 146 19 76 - 300 N/A N/A
- 648 635 305 305 355 511 - - 416 74.63 508 211 447 19.05 571 471 197 146 19 76 -
in.
mm
FULL PORT DIMENSIONS
CLASS 150 THROUGH 1500 & 5000# MOP 6 in. - 12 in. (150 mm - 300 mm) CLASS 600 THROUGH 1500 & 5000# MOP 6 in. (150 mm) CLASS 150 & 300
CLASS 1500 AND 5000# MOP
CLASS 150
A B BB H J K L M N P Q R T U V W XSIZE in. RF RJ
6 15.50 16.00 6.00 6.00 7.06 9.41 11.16 1.503 7.50 9.50 0.375 0.56-(8) 0.88 11.16 12.85 3.39 8.83 12.00
SIZE mm
150 394 406 152 152 179 239 283 38.18 191 241 9.53 - 22 283 326 86 224 305
CLASS 300
CLASS 600
CLASS 900
A B BB H J K L M N P Q R T U V W XSIZE in. RF RJ
6 22.00 22.12 6.00 6.00 7.12 9.41 11.25 1.503 7.50 9.50 0.375 0.56-(8) 0.88 11.16 12.85 3.39 12.26 20.00
8 26.00 26.12 8.00 8.00 9.25 11.75 14.81 1.685 8.00 9.25 0.375 0.66-(8) 1.05 13.91 16.31 5.12 15.25 24.00
10 31.00 31.12 10.00 10.00 11.38 13.69 16.93 2.003 7.50 9.50 0.500 0.56-(8) 1.16 15.86 18.25 5.12 14.85 28.00
12 33.00 33.12 12.00 12.00 13.93 16.13 19.50 2.560 10.25 12.50 0.625 0.69-(8) 1.28 18.30 22.24 8.31 17.61 24.00
SIZE mm
150 559 562 152 152 181 239 286 38.18 191 241 9.53 - 22 283 326 86 311 508
200 660 663 203 203 235 298 376 42.80 203 235 9.53 - 27 353 414 130 387 610
250 787 790 254 254 289 348 430 50.88 191 241 12.70 - 29 403 464 130 377 711
300 838 841 305 305 354 410 495 65.02 260 318 15.88 - 33 465 565 211 447 610
A B BB H J K L M N P Q R T U V W XSIZE in. RF RJ
6 15.88 16.50 6.00 6.00 7.06 9.41 11.16 1.503 7.50 9.50 0.375 0.56-(8) 0.88 11.16 12.85 3.39 8.83 12.00
SIZE mm
150 403 419 152 152 179 239 283 38.18 191 241 9.53 - 22 283 326 86 224 305
A B BB H J K L M N P Q R T U V W X
SIZE in. RF RJ
6 24.00 24.12 6.00 6.00 8.06 10.09 13.12 1.685 8.00 9.25 0.375 0.66-(8) 1.05 12.25 14.65 5.12 15.25 20.00
8 29.00 29.12 8.00 8.00 10.31 12.31 15.31 2.003 7.50 9.50 0.500 0.56-(8) 1.16 14.48 16.88 5.12 14.85 28.00
10 33.00 33.12 10.00 10.00 12.25 14.47 18.93 2.560 10.25 12.50 0.625 0.69-(8) 1.28 16.64 20.58 8.31 17.61 24.00
12 38.00 38.12 12.00 12.00 14.88 17.78 21.56 2.745 10.25 12.50 0.625 0.69-(8) 1.63 19.95 23.89 10.36 19.69 20.00
SIZE mm
150 610 613 152 152 205 256 333 42.80 203 235 9.53 - 27 311 372 130 387 508
200 737 740 203 203 262 313 389 50.88 191 241 12.70 - 29 368 429 130 377 711
250 838 841 254 254 311 368 481 65.02 260 318 15.88 - 33 423 523 211 447 610
300 965 968 305 305 378 452 548 69.72 260 318 15.88 - 41 507 607 263 500 508
A B BB H J K L M N P Q R T U V W X
SIZE in. RF RJ
6 27.75 28.00 6.00 6.00 10.25 11.53 15.15 2.003 8.00 9.75 0.500 0.78-(4) 1.50 13.70 16.10 5.12 15.25 20.00
SIZE mm
150 705 711 152 152 260 293 385 50.88 203 248 12.70 - 38 348 409 130 387
K
H
J
R
A
CLASS 150 AND 300
BW - 79 4
FL 98 122
BW - (36) (100)
FL (44) (55)
FL 118 175
FL (54) (79)
BW - 189 6
FL 162 221
BW - (86) (150)
FL (73) (100)
FL 217 293
FL (98) (133)
BW - 273 8
FL 423 472
BW - (124) (200)
FL (192) (214)
FL 446 582
FL (202) (264)
BW - 686 10
FL 771 934
BW - (311) (250)
FL (350) (424)
FL 867 1047
FL (393) (475)
BW - 873 12
FL 1136 1310
BW - (396) (300)
FL (515) (594)
FL 1178 1398
FL (534) (634)
WEIGHTS lb. (kg) - VALVE ONLY WORM GEAR ACTUATOR WEIGHTS lb. (kg)
SIZE in. CLASS 150 CLASS 300 (mm) SP LP SP LP
4 25 25 26 26
(100) (11) (11) (12) (12)
6 x 4 25 25 26 26
(150 x 100) (11) (11) (12) (12)
6 26 26 26 26
(150) (12) (12) (12) (12)
8 x 6 26 26 26 26
(200 x 150) (12) (12) (12) (12)
8 69 69 69 69
(200) (31) (31) (31) (31)
10 x 8 70 70 70 70
(250 x 200) (32) (32) (32) (32)
10 95 95 122 123
(250) (43) (43) (55) (56)
12 x 10 95 95 123 123
(300 x 250) (43) (43) (56) (56)
12 95 95 123 123
(300) (43) (43) (56) (56)
14 x 12 95 95 123 123
(350 x 300) (43) (43) (56) (56)
Note: Weights shown are for “bare stem” valves. BW = Butt Weld: Available only in Class 300. FL = Flanged End.
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 600 THROUGH 1500 & 5000# MOP 6 in. - 14 in. x 12 in. (150 mm - 350 mm x 300 mm) MATERIALS LIST
BODY GROUP TRIM NUMBER
SEAL GROUP TRIM CODE YFF TFF YRF PFF
PART CLASS 600/1500 600 600/1500 900/1500 FIRE TESTED FIRE TESTED* & 5000# MOP FIRE TESTED
Temperature Limits -20°F to 250°F -20°F to 350°F -50°F to 250°F -20°F to 350°F (-29°C to 121°C) (-29°C to 177°C) (-46°C to 121°C) (-29°C to 177°C)
Seat Face Seals Nylon (N6) Filled PTFE Nylon (N6) PK
Stem Seal O-Rings High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Body/Tailpiece O-Rings High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Seat O-Rings High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Trunnion O-Ring High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Seat Backup Rings Nylon (N6) PK Nylon (N6) PK
Stem backup Rings Nylon (N6) PK Nylon (N6) PK
Note: Trims 21, 23 and 24 are suitable for temperatures from -20°F to 350°F (-29°C to 177°C). Trim 37 is suitable for temperatures from -50°F to 250°F (-46°C to 121°C).
CARBON STEEL CARBON STEEL STAINLESS STEEL PART CARBON STEEL (NACE) LOW TEMP (NACE) (NACE)
21 24 37 23
Body Class 600 through 1500 A216 Gr. WCC /A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Body 5000# MOP A487 Gr. 4 A487 Gr. 4 A487 Gr. 4 N/A
Tailpiece Class 600 through 1500 A216 Gr. WCC /A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Tailpiece 5000# MOP A487 Gr. 4 A487 Gr. 4 A487 Gr. 4 N/A
Lower Cover Plate Class 600 through 1500 Carbon Steel Carbon Steel 4130 316 SS
Lower Cover Plate 5000# MOP 4130 4130 4130 N/A
Studs A193 Gr. B7 A193 Gr. B7M A320 Gr. L7M A193 Gr. B7M Zinc Plate
Nuts A194 Gr. 2H A194 Gr. 2HM A194 Gr. 7ML A194 Gr. 2HM Zinc Plate
Cap Screws A193 Gr. B7 A193 Gr. B7M A320 Gr. L7M A193 Gr. B7M Zinc Plate
Fittings Carbon Steel Stainless Steel Stainless Steel Stainless Steel
Pipe Plug Carbon Steel Stainless Steel Stainless Steel Stainless Steel
Adapter Plate Carbon Steel Carbon Steel 4130 316 SS
Ball Class 600 through 1500 A216 Gr. WCC/A105 CS ENP A351 Gr. CF8M
Ball 5000# MOP 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A564 TYPE 630 ENP
Dowel Pin A564 Type 630 A564 Type 630 A564 Type 630 A564 Type 630
Stem/Trunnion 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A564 Type 630 ENP
Seat Rings Class 600 & 900 A105 A105 A105 A182 Gr. 316/A351 Gr. CF8M
Seat Rings Class 1500 4130 4130 4130 A564 Type 630
Seat Rings 5000# MOP 4130 4130 4130 A564 Type 630
Seat Spring Carbon Steel B637 X750 B637 X750 B637 X750
Stem & Trunnion Bearings SS/Filled PTFE SS/Filled PTFE SS/Filled PTFE SS/Filled PTFE
Thrust Washer Stainless Steel Stainless Steel Stainless Steel Stainless Steel
Ground Spring Stainless Steel Stainless Steel Stainless Steel Stainless Steel
Stem Retainer Pin A564 Type 630 A564 Type 630 A564 Type 630 A564 Type 630
INTERNAL GROUP TRIM NUMBER
* Note: TFF Trim Code does not apply to Class 1500, 2500 & 5000# MOP.
NACE indicates compliance with NACE MR0175. (Rev. 2002)
2710 TC1777 08/04 NP-5M
CLASS 150 AND 300 STEM TORQUE AND FLOW CHARACTERISTICS
STEM TORQUE
* Flow of water in U.S. gal/ min/1 psi pressure drop across a fully o pen valve. (S) Short Pattern. (L) Long Pattern.
FLOW CHARACTERISTICS (C )*V
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 600 THROUGH 1500 & 5000# MOP 6 in. - 14 in. x 12 in. (150 mm - 350 mm x 300 mm)
DynaSeal 370D4 ball valves conform to the following design and testing standards:
• API 6D
• ASME/ANSI B16.5 (Steel Pipe Flanges and Flange Fitting)
• MSS-SP-6 (Standard Finishes for Pipe Flanges)
• MSS-SP-25 (Standard Marking System for Valves)
• MSS-SP-55 (Quality Standards for Steel Castings)
• API 6FA (Fire Test Specification)
In addition DynaSeal 370D4 ball valves can be supplied to comply with these standards:
• ASME/ANSI B31.1 (Power Piping)
• ASME/ANSI B31.3 (Chemical Plant and Petroleum Refinery Piping)
• MSS-SP-61 (Pressure Testing of Steel Valves)
• ASME/ANSI B16.104 (Valve Seat Leakage)
• NACE MR0175 (Rev. 2002)
6 (150) • • •
8 (200) • •
10 (250) • •
12 (300) • •
STANDARDS AND SPECIFICATIONS
7 1/16 x 6 (179 x 152) •
ASME/ANSI PRESSURE CLASS
Body/Tailpiece O-Ring
Body Drain Fitting
Seat Assembly (Consists of Seat Ring and Seat Face Seal in material List)
Seat Spring
Stem Injection Fitting
VALVE PORT PRESSURE TORQUE EXPRESSIONS BREAK RUN RESEAT SIZE (P) BREAK RUN TORQUE TORQUE TORQUE
TORQUE TORQUE @ MAX. P @ MAX. P @ MAX. P In (mm) psig (in-lbs) (in-lbs) (in-lbs) (in-lbs) (in-lbs)
4 (100) 0 - 285 652 + (2.04 x P) 559 + (0.04 x P) 1233 570 925
286 - 500 763 + (1.65 x P) 554 + (0.06 x P) 1588 584 1191
501 - 740 978 + (1.22 x P) 485 + (0.20 x P) 1881 633 1411
6 (150) 0 - 285 1352 + (6.48 x P) 870 + (0.57 x P) 3199 1032 2399
286 - 500 2423 + (2.72 x P) 730 + (1.06 x P) 3792 1260 2844
501 - 740 2332 + (2.90 x P) 760 + (1.00 x P) 4478 1500 3359
8 (200) 0 - 285 2380 + (13.23 x P) 1737 + (1.27 x P) 6151 2099 4613
286 - 500 3441 + (9.48 x P) 1263 + (2.93 x P) 8181 2728 6136
501 - 740 1434 + (13.47 x P) 480 + (4.49 x P) 11402 3803 8551
10 (250) 0 - 285 5514 + (27.43 x P) 3808 + (2.64 x P) 13332 4560 9999
286 - 500 9244 + (14.30 x P) 3357 + (4.21 x P) 16394 5462 12296
501 - 740 8134 + (16.49 x P) 2713 + (5.49 x P) 20337 6776 15252
12 (300) 0 - 285 6181 + (43.61 x P) 3596 + (9.15 x P) 18610 6204 13957
286 - 500 11507 + (24.84 x P) 3837 + (8.28 x P) 23927 7977 17945
501 - 740 8773 + (30.25 x P) 2938 + (10.06 x P) 31158 10382 23369
VALVE SIZE BUTT WELD VALVE PRESSURE in. (mm) END VALVE CLASS 150 CLASS 300
4 x 4 (100 x 100) 2118 2446 2118
6 x 4 (150 x 100) 390 391 (S) 390
6 x 6 (150 x 150) 5403 6644 (S) / 5468 (L) 5403
8 x 6 (200 x 150) 1215 1219 (S) / 1215 (L) 1215 (S)
8 x 8 (200 x 200) 11261 10782 11261 (S) / 10293 (L)
10 x 8 (250 x 200) 2671 2672 2670
10 x 10 (250 x 250) 17037 17438 18835 (S) / 16894 (L)
12 x 10 (300 x 250) 4881 4885 4879
12 x 12 (300 x 300) 26163 26702 25905
14 x 12 (350 x 300) 10580 10076 10580
1126 TC1777 08/04 NP-5M
TC1777 08/04 NP-5M
The above values are new valve torque values, where P is the maximum operating pressure (psig) of the valve.
The above torque values do not contain service factors. Soaking effects and/or particle matter in the valve may cause
an increase in the torque.
For interpolated torque calculations, use the torque expressions corresponding to the applicable pressure range only.
For example, a pressure of 400 psig uses the torque equations in the 286-500 psig pressure range only.
The reseat torque is taken as 0.75 times the break torque. For power operation, multiply all of the above values by a
factor of 1.25 or customer specified factor whichever is larger.
For operating temperatures between -20°F to -50°F (-29°C to -46°C), multiply these values by 1.20.
Actuator selection should be made based on customer experience and appropriate service factors.
Stem Retainer Pin
®DYNASEAL 370D4 TRUNNION BALL VALVES
2 in. - 6 in. x 4 in. (50 mm - 150 mm x 100 mm)
Locking Device Standard on Manual Valves.
Body Bleed Fitting for Double Block and Bleed Applications.
®W-K-M DynaSeal 370D4 Trunnion Ball Valve is engineered and designed for heavy duty performance. Meets API 6D specifications for general purpose petroleum and chemical process applications.
Seat Face Seals are Available in Nylon and Other Materials.
Field Repairable 2 Piece Body.
Integral Actuator Mounting Flange.
BODY GROUP TRIM NUMBER
CARBON STEEL CARBON STEEL STAINLESS STEEL PART CARBON STEEL (NACE) LOW TEMP (NACE) (NACE)
21 24 37 23
Body A216 Gr. WCC/ A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Tailpiece A216 Gr. WCC/ A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Studs A193 Gr. B7 A193 Gr. B7M A320 Gr. L7M A193 Gr. B7M Zinc Plate
Nuts A194 Gr. 2H A194 Gr. 2HM A194 Gr. 7ML A194 Gr. 2HM Zinc Plate
Bolt-Trunnion A193 Gr. B7 A193 Gr. B7M A320 Gr. L7M A193 Gr. B7M Zinc Plate
Stem Bearing CS/Filled PTFE CS/Filled PTFE CS/Filled PTFE SS/Filled PTFE
Trunnion Bearing CS/Filled PTFE CS/Filled PTFE CS/Filled PTFE SS/ Filled PTFE
Fittings Carbon Steel Stainless Steel Stainless Steel Stainless Steel
Stop Plate Carbon Steel Carbon Steel Carbon Steel Carbon Steel
Wrench Ductile Iron Ductile Iron Ductile Iron Ductile Iron
Adapter Plate Carbon Steel Carbon Steel 4130 Carbon Steel
Lower Cover Plate Carbon Steel Carbon steel 4130 316 SS
Ball A105 CS ENP A105 CS ENP A105 CS ENP A182 Gr. 316 SS
Stem 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A564 Type 630 SS
Trunnion 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A564 Type 630 SS
Seat Rings 1018/1029 CS 1018/1029 CS 1018/1029 CS A182 Gr. 316 SS
Seat Springs Carbon Steel B637 X750 B637 X750 B637 X750
Grounding Spring Stainless Steel Stainless Steel Stainless Steel Stainless Steel
Stem Retainer Pin AS64 Type 630 AS64 Type 630 AS64 Type 630 AS64 Type 630
SEAL GROUP TRIM CODE
PART YFF FIRE TESTED TFF FIRE TESTED YRF
Temperature Limits -20°F to 250°F (-29°C to 121°C) -20°F to 350°F (-29°C to 177°C) -50°F to 250°F (-46°C to 121°C)
Seat Face Seals Nylon (N6) Filled PTFE Nylon (N6)
Seat Backup Rings Nylon (N6) PK Nylon (N6)
Stem Backup Rings Nylon (N6) PK Nylon (N6)
Stem Thrust Washer 304 SS 304 SS 304 SS
Stem O-Rings High Fluorine FKM High Fluorine FKM HNBR
Body/Tailpiece O-Ring High Fluorine FKM High Fluorine FKM HNBR
Trunnion O-Ring High Fluorine FKM High Fluorine FKM HNBR
INTERNAL GROUP TRIM NUMBER
Note: Trims 21, 23 and 24 are suitable for temperatures from -20°F to 350°F (-29°C to 177°C). Trim 37 is suitable for temperatures from -50°F to 250°F (-46°C to 121°C).
NACE indicates compliance with NACE MR0175. (Rev. 2002)
CLASS 150 AND 300 6 in. & 8 in. x 6 in. (150 mm & 200 mm x 160 mm) MATERIALS LIST
2512 TC1777 08/04 NP-5M
®DYNASEAL 370D4 TRUNNION BALL VALVES
Secondary seat sealant injection fittings are standard on Class 600 and higher pressure classes and optional on lower pressure classes
Stem sealant injection is optional on 2 in. - 4 in. (50 mm - 100 mm)
INDICATOR HANDLE When the handle is aligned with the pipe, the valve is open. When the handle is perpendicular to the pipe, the valve is closed.
DESIGN STANDARDS See page 14.
POSITIVE DOUBLE BLOCK AND BLEED OPERATION The pressure actuated seats and bleed fittings allow double block and bleed operation. When used for block and bleed, this feature permits the valve to take the place of two valves. It also allows the operator to check up and downstream sealing by bleeding off the body pressure.
AUTOMATIC BODY PRESSURE RELIEF Seats will internally relieve excess body pressure.
FIRE TESTED FOR SAFETY DynaSeal 370 valves are qualified under API standard 6FA and API 607 4th Edition.
See seal group for qualified trims.
The end entry ball valve for gas, oil and product pipelines, it’s the choice for gas distribution and other specialized applications.
DynaSeal 370D4 ball valve offers all the required features and options demanded by the gas transmission, gas distribution and oilfield production industries. Seat and stem sealant injection fittings, low pressure sealability comply with ASME/ANSI B16.34, API 6D, API 6FA and API 607 4th Edition standards. The end connections may be specified in flanged, weld end or weld by flanged end connections.
FEATURES AND BENEFITS
PRESSURE ACTUATED SEATS This valve uses pressure-actuated seats with locked-in non-metallic face seals. To assure tight sealing at low pressures, special wave springs force the seats against the ball. At higher pressures, the upstream seat is forced against the ball by the pressure working across the differential between the area of the seat insert and the seat O-ring. The higher the pressure, the tighter the seal.
SECONDARY SEAT SEALANT INJECTION In the event of damage to the valve seat, sealant can be injected to temporarily seal the valve until repair can be performed. (Optional in 2 inch - 4 inch (50 mm - 100 mm) Class 150/300 and standard in all others.)
FIELD REPAIRABLE The split body design permits complete repairs to be made in the field without special tools.
®DYNASEAL 370D4 TRUNNION BALL VALVES
DynaSeal 370D4 ball valves conform to the following design and testing standards:
• API 6D
• ASME/ANSI B16.5 (Steel Pipe Flanges and Flange Fitting)
• MSS-SP-6 (Standard Finishes for Pipe Flanges)
• MSS-SP-25 (Standard Marking System for Valves)
• MSS-SP-55 (Quality Standards for Steel Castings)
• API 6FA (Fire Test Specification)
In addition DynaSeal 370D4 ball valves can be supplied to comply with these standards:
• ASME/ANSI B31.1 (Power Piping)
• ASME/ANSI B31.3 (Chemical Plant and Petroleum Refinery Piping)
• MSS-SP-61 (Pressure Testing of Steel Valves)
• ASME/ANSI B16.104 (Valve Seat Leakage)
• NACE MR0175 (Rev. 2002)
STANDARDS AND SPECIFICATIONS ASME/ANSI PRESSURE CLASS
SIZE CLASS in. (mm) 150 300
6 (150) • •
Grounding Spring
Trunnion Bearing
Lower Cover Plate
Seat Assembly (Consists of Seat Ring and Seat Face Seal in material List)
Body/Tailpiece O-Ring
Pipe Plug
CLASS 150 AND 300 6 in. & 8 in. x 6 in. (150 mm & 200 mm x 160 mm)
Stem Injection Fitting
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 150 THROUGH 2500 & 5000# MOP 2 in. - 6 in. x 4 in. (50 mm - 150 mm x 100 mm)
Grounding Spring
Trunnion Bearing
Stud
Nut
Seat Assembly (Consists of Seat Ring and Seat Face Seal in Material List)
Seat O-Rings
Stem
Nut
Stud
DynaSeal 370D4 ball valves conform to the following design and testing standards:
• API 6D
• ASME/ANSI B16.5 (Steel Pipe Flanges and Flange Fitting)
• MSS-SP-6 (Standard Finishes for Pipe Flanges)
• MSS-SP-25 (Standard Marking System for Valves)
• MSS-SP-55 (Quality Standards for Steel Castings)
• API 6FA (Fire Test Specification)
In addition DynaSeal 370D4 ball valves can be supplied to comply with these standards:
• ASME/ANSI B31.1 (Power Piping)
• ASME/ANSI B31.3 (Chemical Plant and Petroleum Refinery Piping)
• MSS-SP-61 (Pressure Testing of Steel Valves)
• ASME/ANSI B16.104 (Valve Seat Leakage)
• NACE MR0175 (Rev. 2002)
SIZE in. (mm) 5000# MOP
2 1/16 (52) •
3 1/8 (80) •
4 1/16 (103) •
Bleed and Drain Fitting
SIZE CLASS in. (mm) 150 300 600 900 1500 2500
2 (50) • • • • • •
3 (80) • • • • • •
4 (100) • • • • • •
®DYNASEAL 370D4 TRUNNION BALL VALVES
FIRE TESTED FOR SAFETY
• DynaSeal 370D4 valves are qualified under API 6FA and API 607 4th Edition standards.
ACTUATION-FRIENDLY
• A variety of actuator types can be easily installed.
• Cooper Cameron Valves can provide a total package of valves, actuators or worm gear mounting plates to accommodate actuation.
END CONNECTIONS
BODY STYLES
OPTIONAL MATERIALS
Special trims available upon request.
DOUBLE BLOCK AND BLEED OPERATION
The pressure actuated seats and bleed fittings allow double block and bleed operation.
When used for block and bleed, this feature may permit the valve to take the place of two valves.
It also allows the operator to check up and downstream sealing by bleeding off the body pressure.
FEATURES AND BENEFITS
Check Valve
BI-DIRECTIONAL FLOW This valve uses pressure actuated seats with locked-in non-metallic face seals. To assure sealing at low pressure, special wave springs force the seats against the ball. At higher pressures, the upstream seat is forced against the ball by the pressure working across the differential area between the seat insert and the seat O-Ring. The higher the pressure, the tighter the seal.
SECONDARY SEAT SEAL INJECTION In the event of damage to the valve seat, sealant can be injected to temporarily seal the valve.
AUTOMATIC BODY PRESSURE RELIEF Seats will internally relieve excess body pressure.
BI-DIRECTIONAL FLOW
BODY GROUP TRIM NUMBER
CARBON STEEL CARBON STEEL STAINLESS STEEL PART CARBON STEEL (NACE) LOW TEMP (NACE) (NACE)
21 24 37 23
Body A216 Gr. WCC/ A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Body 5000# MOP A487 Gr. 4 A487 Gr. 4 A487 Gr. 4 N/A
Tailpiece A216 Gr. WCC/ A105 A216 Gr. WCC/ A105 A352 Gr. LCC/ A350 Gr. LF2 A351 Gr. CF8M/ 316 SS
Tailpiece 5000# MOP A-487 Gr. 4 A-487 Gr. 4 A-487 Gr. 4 N/A
Studs A193 Gr. B7 A193 Gr. B7M A320 Gr. L7M A193 Gr. B7M Zinc Plate
Nuts A194 Gr. 2H A194 Gr. 2HM A194 Gr. 7ML A194 Gr. 2HM Zinc Plate
Cap Screws A193 Gr. B7 A193 Gr. B7M A320 Gr. L7M A193 Gr. B7M Zinc Plate
Stem Stop CS Zinc Plate CS Zinc Plate CS Zinc Plate CS Zinc Plate
Stem Bearing CS/Filled PTFE CS/Filled PTFE CS/Filled PTFE SS/Filled PTFE
Trunnion Bearing CS/Filled PTFE CS/Filled PTFE CS/Filled PTFE SS/Filled PTFE
Fittings Carbon Steel Stainless Steel Stainless Steel Stainless Steel
Stop Plate Carbon Steel Carbon Steel Carbon Steel Carbon Steel
Lever Handle Ductile Iron Ductile Iron Ductile Iron Ductile Iron
Lower Cover Plate Carbon Steel Carbon Steel 4130 316 SS
Ball Class 150 through 2500 A105 CS ENP A105 CS ENP A105 CS ENP A182 Gr. 316 SS
Ball 5000# MOP 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A182 Gr. 316 SS
Stem 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A564 Type 630 SS ENP
Trunnion 4130/4140 ENP 4130/4140 ENP 4130/4140 ENP A564 Type 630 SS ENP
Seat Rings Class 150 through 900 1018/1029 CS 1018/1029 CS 1018/1029 CS A182 Gr. 316 SS
Seat Rings Class 1500, 2500 & 5000# MOP 4130 4130 4130 A564 Type 630 SS
Seat Springs Carbon Steel B637 X750 B637 X750 B637 X750
Grounding Spring Stainless Steel Stainless Steel Stainless Steel Stainless Steel
SEAL GROUP TRIM CODE (Note Pressure Classes) YFF TFF YRF PFF
PART CLASS 150/2500 & 5000# MOP 150/600 150/2500 900/2500 & 5000# MOP FIRE TESTED FIRE TESTED* FIRE TESTED FIRE TESTED
Temperature Limits -20°F to 250°F -20°F to 350°F -50°F to 250°F -20°F to 350°F (-29°C to 121°C) (-29°C to 177°C) (-46 to 121°) (-29°C to 177°C)
Seat Face Seals Class 150 through 900 Nylon (N6) Filled PTFE Nylon (N6) PK
Seat Face Seals Class 1500, 2500 & 5000# MOP Nylon (N6) N/A Nylon (N6) PK
Stem Seal Class 150 through 900 Filled PTFE Filled PTFE Filled PTFE Filled PTFE
Stem Seal Class 1500, 2500 & 5000# MOP PK N/A PK PK
Stem O-Rings High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Body/Tail Piece O-Ring High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Seat O-Rings High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
Trunnion O-Ring High Fluorine FKM High Fluorine FKM HNBR High Fluorine FKM
O-Ring Backup Ring Class 1500, 2500 & 5000# MOP PK N/A PK PK
INTERNAL GROUP TRIM NUMBER
Note: Trims 21, 23 and 24 are suitable for ambient temperatures from -20°F to 350°F (-29°C to 177°C). Trim 37 is suitable for ambient temperatures from -50°F to 350°F (-46°C to 177°C).
* Note: TFF Trim Code does not apply to Class 900, 1500, 2500 & 5000# MOP.
** Not shown on page 14.
NACE indicates compliance with NACE MR0175. (Rev. 2002)
®DYNASEAL 370D4 TRUNNION BALL VALVES
**
CLASS 150 THROUGH 2500 & 5000# MOP 2 in. - 6 in. x 4 in. (50 mm - 150 mm x 100 mm) MATERIALS LIST
®DYNASEAL 370D4 TRUNNION BALL VALVES
®W-K-M DynaSeal 370D4 Series Trunnion Ball Valve is engineered and designed for heavy duty performance. Used in many general purpose petroleum and chemical process applications; also specified for more demanding applications
Standard adapter flange for ease of automation.
Stem is positively retained, cannot be removed with valve in service.
Provisions for stem sealant injection.
Secondary seat sealant injection fittings.
Ball is held fast by trunnion, but free to turn easily at any pressure.
Pressure-actuated seat provides positive seal under all conditions.
6 in. - 14 in. x 12 in. (150 mm - 350 mm x 300 mm)
1522 TC1777 08/04 NP-5M
Stem retainer and pipe plug shown 180° out of position.
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 150 THROUGH 900 2 in. - 4 in. x 3 in. (50 mm - 100 x 80 mm)
DETAIL WITH 2 in. (50 mm) SQUARE NUT
VALVE WITH GEAR
R
U
T
AA
V
REDUCED PORT DIMENSIONS
FULL PORT DIMENSIONS CLASS 1500 AND 5000# MOP
SIZE A B C D E F G H J L M N P R S T U V W X Y Z AA BB
in. RF RJ
2 14.50 14.62 2.00 2.00 6.29 4.06 5.58 1.52 1.118 2.656 0.690 1/2-13UNC 0.50 10.34 8.12 10.00 4.92 0.56 2.80 8.75 3.00 6.40 1.328 1/2-18 -
3 18.50 18.62 3.00 3.00 7.29 4.75 6.96 2.21 1.496 3.375 0.994 1/2-13UNC 0.50 12.03 8.82 16.00 4.92 0.56 2.80 10.44 3.00 7.47 2.030 3/4-36 -
4 21.50 21.63 4.00 4.00 8.47 6.68 8.72 2.04 1.496 4.500 - 5/8-11UNC 0.63 14.12 9.73 16.00 6.50 0.56 3.39 12.47 3.00 9.44 2.250 3/4-36 0.375
SIZE mm
50 368 371 51 51 160 103 142 39 28.40 67 17.53 - 13 263 206 254 125 14 71 222 76 163 34 - -
80 470 473 76 76 185 121 177 56 38.00 86 25.25 - 13 306 224 406 125 14 71 265 76 190 52 - -
100 546 549 102 102 215 170 221 52 38.00 114 - - 16 359 247 406 165 14 86 317 76 240 57 - 9.53
CLASS 2500
CLASS 1500 AND 5000# MOP
SIZE A B C D E F G H J L M N P R S T U V W X Y Z AA BB
in. RF RJ
2 17.75 17.88 1.78 1.78 6.29 4.06 5.68 1.62 0.995 3.500 - 1/2-13UNC 0.50 10.34 8.12 10.00 4.92 0.56 2.80 8.75 3.00 6.70 1.750 1/2-18 0.250
3 22.75 23.00 2.56 2.56 7.72 6.31 8.30 2.00 1.496 4.000 - 1/2-13UNC 0.50 13.75 9.73 16.00 5.51 0.56 3.39 12.10 3.00 9.07 2.030 3/4-36 0.375
4 26.50 26.88 3.53 3.53 8.47 7.25 10.05 2.80 1.683 4.625 - 5/8-11UNC 0.63 15.09 13.64 20.00 4.92 0.56 4.11 13.20 3.00 2.312 - 0.375
SIZE mm
50 451 454 45 45 160 103 144 41 25.27 89 - - 13 263 206 254 125 14 71 222 76 170 44 - 6.35
80 578 584 65 65 196 160 211 51 38.00 102 - - 13 349 247 406 140 14 86 307 76 230 52 - 9.53
100 673 683 90 90 215 184 255 71 42.75 117 - - 16 383 346 508 125 14 104 335 76 59 - 9.53
A B C D E F G H J L M N P R S T U V W X Y Z AA BB
SIZE in. RF RJ
6 x 4 27.75 28.00 4.00 5.81 8.59 6.68 8.72 2.04 1.496 4.500 - 5/8-11UNC 0.63 14.12 9.73 16.00 6.50 0.56 3.39 12.47 3.00 9.44 2.250 3/4-36 0.375
SIZE mm
150 x 100 705 711 102 148 218 170 221 52 38.00 114 - - 16 359 247 406 165 14 86 317 76 240 57 - 9.53
CLASS 2500
A B C D E F G H J L M N P R S T U V W X Y Z AA BB
SIZE in. RF RJ
6 x 4 36.00 36.50 3.53 5.31 8.90 7.25 10.05 2.80 1.683 4.625 - 5/8-11UNC 0.63 15.09 13.64 20.00 4.92 0.56 4.11 13.20 3.00 - 2.312 - 0.375
SIZE mm
150 x 100 914 927 90 135 226 184 255 71 42.75 117 - - 16 383 346 508 125 14 104 335 76 59 - 9.53
CLASS 1500 & 2500 & 5000# MOP
2116 TC1777 08/04 NP-5M
CLASS 150 THROUGH 900
REDUCED PORT DIMENSIONS
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
3 x 2 14.00 14.12 2.00 3.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.55 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
4 x 3 17.00 17.12 3.00 4.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
80 x 50 356 359 51 76 130 84 122 39 28.24 68 - 17.48 - 14 224 184 152 102 14 52 381 148 141 195 76
100 x 80 432 435 76 102 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
FULL PORT DIMENSIONS CLASS 150
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 7.00 7.50 2.00 2.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.40 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
3 8.00 8.50 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
50 178 191 51 51 130 84 122 39 28.24 68 - 17.48 - 10 224 184 152 102 14 52 381 148 141 195 76
80 203 216 76 76 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
CLASS 300
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 8.50 9.12 2.00 2.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.40 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
3 11.12 11.75 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
50 216 232 51 51 130 84 122 39 28.24 68 - 17.48 - 10 224 184 152 102 14 52 381 148 141 195 76
80 282 298 76 76 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
CLASS 600
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 11.50 11.62 2.00 2.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.55 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
3 14.00 14.12 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
50 292 295 51 51 130 84 122 39 28.24 68 - 17.48 - 14 224 184 152 102 14 52 381 148 141 195 76
80 356 359 76 76 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
CLASS 900
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 14.50 14.62 2.00 2.00 5.11 3.73 5.25 1.52 1.112 2.66 1/2-13UNC 0.688 1/2-13UNC 0.55 9.25 7.25 6.00 4.02 0.56 2.05 15.00 6.25 6.00 8.12 3.00
3 15.00 15.12 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 11.09 8.12 10.00 4.92 0.56 2.80 15.00 6.67 7.08 9.50 3.00
SIZE mm
50 368 371 51 51 130 95 133 39 28.24 68 - 17.48 - 14 235 184 152 102 14 52 381 159 152 206 76
80 381 384 76 76 151 122 162 40 28.24 76 - 17.48 - 14 282 206 254 125 14 71 381 169 180 241 76
CLASS 600
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
3 x 2 15.00 15.12 2.00 3.00 5.11 3.73 5.25 1.52 1.112 2.66 1/2-13UNC 0.688 1/2-13UNC 0.55 9.25 7.25 6.00 4.02 0.56 2.05 15.00 6.25 6.00 8.12 3.00
4 x 3 18.00 18.12 3.00 4.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 11.09 8.12 10.00 4.92 0.56 2.80 15.00 6.67 7.08 9.50 3.00
SIZE mm
80 x 50 381 384 51 76 130 95 133 39 28.24 68 - 17.48 - 14 235 184 152 102 14 52 381 159 152 206 76
100 x 80 457 460 76 102 151 122 162 40 28.24 76 - 17.48 - 14 282 206 254 125 14 71 381 169 180 241 76
CLASS 900
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 1500 & 2500 & 5000# MOP 2 in. - 6 in. x 4 in. (50 mm - 150 mm x 100 mm)
DETAIL WITH MULTIHEAD
R
U
T
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 150 THROUGH 900 4 in. - 6 in. x 4 in. (100 mm - 150 mm x 100 mm)
®DYNASEAL 370D4 TRUNNION BALL VALVES
REDUCED PORT DIMENSIONS
FULL PORT DIMENSIONS CLASS 150
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 9.00 9.50 4.00 4.00 7.19 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 8.00 7.88
SIZE mm
100 229 241 102 102 183 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 203 200
CLASS 300
CLASS 600
CLASS 900
CLASS 150 THROUGH 900
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 12.00 12.63 4.00 4.00 7.19 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
100 305 321 102 102 183 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 17.00 17.13 4.00 4.00 7.19 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
100 432 435 102 102 183 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 18.00 18.13 4.00 4.00 7.31 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 18.00 11.35
SIZE mm
100 457 461 102 102 186 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 457 288
CLASS 150
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 15.50 16.00 4.00 6.00 7.30 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 8.00 7.88
SIZE mm
150 x 100 394 406 102 152 185 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 203 200
CLASS 300
CLASS 600
CLASS 900
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 15.88 16.50 4.00 6.00 7.30 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
150 x 100 403 419 102 152 185 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 22.00 22.13 4.00 6.00 7.30 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
150 x 100 559 562 102 152 185 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 24.00 24.13 4.00 6.00 7.43 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 18.00 11.35
SIZE mm
150 x 100 610 613 102 152 189 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 457 288
DETAIL WITH MULTIHEAD (See Page 3 for Option Details)
H
B
DIA
J
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 150 THROUGH 900 4 in. - 6 in. x 4 in. (100 mm - 150 mm x 100 mm)
®DYNASEAL 370D4 TRUNNION BALL VALVES
REDUCED PORT DIMENSIONS
FULL PORT DIMENSIONS CLASS 150
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 9.00 9.50 4.00 4.00 7.19 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 8.00 7.88
SIZE mm
100 229 241 102 102 183 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 203 200
CLASS 300
CLASS 600
CLASS 900
CLASS 150 THROUGH 900
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 12.00 12.63 4.00 4.00 7.19 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
100 305 321 102 102 183 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 17.00 17.13 4.00 4.00 7.19 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
100 432 435 102 102 183 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
4 18.00 18.13 4.00 4.00 7.31 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 18.00 11.35
SIZE mm
100 457 461 102 102 186 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 457 288
CLASS 150
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 15.50 16.00 4.00 6.00 7.30 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 8.00 7.88
SIZE mm
150 x 100 394 406 102 152 185 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 203 200
CLASS 300
CLASS 600
CLASS 900
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 15.88 16.50 4.00 6.00 7.30 6.25 8.52 2.27 1.49 0.375 0.994 26.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
150 x 100 403 419 102 152 185 159 216 58 38 10 25 660 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 22.00 22.13 4.00 6.00 7.30 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 10.00 8.12
SIZE mm
150 x 100 559 562 102 152 185 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 254 206
A B C D E F G H J K L M N P R S T U V W X Y Z
SIZE in. RF RJ
6 x 4 24.00 24.13 4.00 6.00 7.43 6.25 8.52 2.27 1.49 0.375 0.994 48.00 10.26 9.61 3/4-36 8.65 0.56 4.921 6.25 10.31 8.62 2.80 18.00 11.35
SIZE mm
150 x 100 610 613 102 152 189 159 216 58 38 10 25 1219 261 244 - 220 14 125 159 262 219 71 457 288
DETAIL WITH MULTIHEAD (See Page 3 for Option Details)
H
B
DIA
J
CLASS 150 THROUGH 900
REDUCED PORT DIMENSIONS
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
3 x 2 14.00 14.12 2.00 3.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.55 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
4 x 3 17.00 17.12 3.00 4.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
80 x 50 356 359 51 76 130 84 122 39 28.24 68 - 17.48 - 14 224 184 152 102 14 52 381 148 141 195 76
100 x 80 432 435 76 102 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
FULL PORT DIMENSIONS CLASS 150
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 7.00 7.50 2.00 2.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.40 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
3 8.00 8.50 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
50 178 191 51 51 130 84 122 39 28.24 68 - 17.48 - 10 224 184 152 102 14 52 381 148 141 195 76
80 203 216 76 76 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
CLASS 300
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 8.50 9.12 2.00 2.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.40 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
3 11.12 11.75 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
50 216 232 51 51 130 84 122 39 28.24 68 - 17.48 - 10 224 184 152 102 14 52 381 148 141 195 76
80 282 298 76 76 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
CLASS 600
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 11.50 11.62 2.00 2.00 5.11 3.29 4.80 1.52 1.112 2.66 1/2-13UNC 0.688 3/8-16UNC 0.55 8.81 7.25 6.00 4.02 0.56 2.05 15.00 5.81 5.56 7.68 3.00
3 14.00 14.12 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 10.33 7.25 6.00 4.02 0.56 2.05 15.00 6.67 7.08 9.20 3.00
SIZE mm
50 292 295 51 51 130 84 122 39 28.24 68 - 17.48 - 14 224 184 152 102 14 52 381 148 141 195 76
80 356 359 76 76 151 122 162 40 28.24 76 - 17.48 - 14 262 184 152 102 14 52 381 169 180 234 76
CLASS 900
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
2 14.50 14.62 2.00 2.00 5.11 3.73 5.25 1.52 1.112 2.66 1/2-13UNC 0.688 1/2-13UNC 0.55 9.25 7.25 6.00 4.02 0.56 2.05 15.00 6.25 6.00 8.12 3.00
3 15.00 15.12 3.00 3.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 11.09 8.12 10.00 4.92 0.56 2.80 15.00 6.67 7.08 9.50 3.00
SIZE mm
50 368 371 51 51 130 95 133 39 28.24 68 - 17.48 - 14 235 184 152 102 14 52 381 159 152 206 76
80 381 384 76 76 151 122 162 40 28.24 76 - 17.48 - 14 282 206 254 125 14 71 381 169 180 241 76
CLASS 600
A B C D E F G H J K L M N P R S T U V W X Y Z AA
SIZE in. RF RJ
3 x 2 15.00 15.12 2.00 3.00 5.11 3.73 5.25 1.52 1.112 2.66 1/2-13UNC 0.688 1/2-13UNC 0.55 9.25 7.25 6.00 4.02 0.56 2.05 15.00 6.25 6.00 8.12 3.00
4 x 3 18.00 18.12 3.00 4.00 5.96 4.81 6.38 1.57 1.112 3.00 1/2-13UNC 0.688 1/2-13UNC 0.55 11.09 8.12 10.00 4.92 0.56 2.80 15.00 6.67 7.08 9.50 3.00
SIZE mm
80 x 50 381 384 51 76 130 95 133 39 28.24 68 - 17.48 - 14 235 184 152 102 14 52 381 159 152 206 76
100 x 80 457 460 76 102 151 122 162 40 28.24 76 - 17.48 - 14 282 206 254 125 14 71 381 169 180 241 76
CLASS 900
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 1500 & 2500 & 5000# MOP 2 in. - 6 in. x 4 in. (50 mm - 150 mm x 100 mm)
DETAIL WITH MULTIHEAD
R
U
T
®DYNASEAL 370D4 TRUNNION BALL VALVES
CLASS 150 THROUGH 900 2 in. - 4 in. x 3 in. (50 mm - 100 x 80 mm)
DETAIL WITH 2 in. (50 mm) SQUARE NUT
VALV

Recommended