Course Contents - VNS Civil.pdf · Course Contents Category of ... Definition and scope of soil...

2

W.e.f.-July – 2010 Academic Section-2010-11

Course ContentsCategory of

CourseCourse Title Course Code Credits-4C Theory Papers (ES)

Civil Engineering Department

DC-18

Design of Hydraulic Structure

CE701 L T P Max.Marks-100 Min.Marks-35Duration-3hrs.

3 1 0

Branch: Civil Engineering-VII SemesterCourse: CE701 Design of Hydraulic Structure Unit - IGravity dams: Design Criteria, forces acting on gravity dams, elementary profile, low and high gravity dams, stability analysis, evaluation of profile by method of zoning, practical profile, foundation treatment, construction joints, galleries in gravity dams.Unit - IIEarth and Rock fill dams :Earth Dams: Types, causes of failure and design criteria, soils suitable for earth dam construction, construction methods, foundation requirements, typical earth dam sections, estimation of seepage through and below the dam, seepage control, stability of slopes by slip circle method of analysis, pore pressures, sudden draw down, steady seepage and construction pore pressure condition.Rock fill dams: Types, merits and demerits, conditions favourable for their adoption. Unit - IIISpillways : Ogee spillway and its design, details of syphon, shaft, chute and side channel spillways, emergency spillways.Unit - IV Energy dissipatiors and gates : Principles of energy dissipation Energy dissipators based on tail water rating curve and jump height curves Spillway crest gates - vertical lift and radial gates, their design principles and details. Design of canal regulating structures, Detaild design of Sarda Falls, design of cross drainage works, sphypon aquaduct.Unit - VHydropower Plants: Introduction of Hydropower development, assessment of power potential, types of hydropower plants, general features of hydro-electric schemes, selection of turbines, draft tubes, surge tanks, penstocks, power house dimensions, development of micro hydel stations, tidal plants, pumped storage plants and their details.

Reference Books: -

1. Engineering for Dams (Volumes I, II & III) by Creager, Justin & Hinds2. Hydroelectric Hand Book by Creager3. Hydraulic Structures by Varshney4. Irrigation & Water Power Engg. by Punmia & Pandey5. Water Power Engineering by Dandekar

\

3


Course Contents Category of

CourseCourse Title Course Code Credits-6 Theory Papers (ES)


DC-19

Advanced Structural Design – II (RCC)

CE702 L T P Max.Marks-100Min.Marks-35Duration-3hrs.

3 1 2

Branch: Civil Engineering-VII SemesterCourse: CE702 Advanced Structural Design – II (RCC) Unit - IDesign of Multistory Buildings - Sway and nonsway buildings, Shear walls and other bracing elements.

Unit II Earth Retaining Structures: Cantilever and counter fort types retaining walls.

Unit - IIIWater Tanks: Tanks on ground and underground tanks: Square, rectangular, circular tanks, Overhead tanks: square, rectangular, circular & intze tanks. Unit - IVSilos and Bunkers Unit - VT-beam & Slab bridges- for highway loading (IRC Loads).Prestressing concepts materials, systems of prestressing & losses Introduction to working & limit State Design.

Suggested Books: -

1. R.C.C. by O.P. Jain Vol. II 2. R.C.C. by B.C. Punmia 3. Essentials of Bridge engineering – D.J. Victor4. Bridge Engineering - Ponnuswamy 5. Advanced R.C.C. Design by N.K. RAJU6. N.Krishna Raju, Prestressed Concrete, Tata Mc Graw Hill, New Delhi.7. Pre stresses concrete – T.Y. Lin

4


Course ContentsCategory of



DC-20

Environmental Engg. - II


3 1 2

Branch: Civil Engineering-VII SemesterCourse: CE703 Environmental Engg. - II Unit - ISewerage schemes and their importance, collection & conveyance of sewage, storm water quantity, fluctuation in sewage flow, flow through sewer, design of sewer, construction & maintenance of sewer, sewer appurtenances, pumps & pumping stations. Unit -IICharacteristics and analysis of waste wate, rcycles of decomposition, physical, chemical & biological parameters. Oxygen demand i.e. BOD & COD, TOC, TOD, Th OD, Relative Stability, population equivalent, instrumentation involved in analysis, natural methods of waste water disposal i.e. by land treatment & by dilution, self purification capacity of stream, Oxygen sag analysis.

Unit -IIIUnit operations for waste water treatment, preliminary treatment such as screens, grit chamber, floatation tank, sedimentation and chemical clarification, role of micro-organism in biological treatment, Sewage filtration- theory & design.

Unit - IVMethods of Biological Treatment (Theory & Design) - Activated Sludge process, Oxidation ditch, stabilization ponds, aerated lagoon, anaerobic lagoons, septic tank & imhoff tank, sources & treatment of sludge, sludge thickening and digestion sludge drying beds, sludge disposal. Unit - V Advanced Waste Water treatment - Diatomaceorus earth filters, ultrafiltration, Adsorption by activated carbon, Phosphorus removal, Nitrogen removal, Physico chemical waste water treatment, Solid waste disposal - classification, composition, collection, & disposal methods.Rural sanitation - collection & disposal of refuse, sullage & night soil

Laboratory work shall be based on the topics of environmental engineering I & II and consist of experiments of water and waste water quality as per facility available in the institution.

List of Experiment1. To study the various standards for waste water2. To study the sampling techniques for waste water3. To determine the alkalinity in water sample4. To determine the acidity in water sample5. Determination of Dissolved Oxygen in the water and waste water sample6. Determination of Biological Oxygen demand of a waste water sample7. Determination of Chemical Oxygen demand of a waste water sample8. Determination of various types of solids in the waste water sample9. Determination of bacterial number by membrane filter Technique10. Determination of bacterial colonies by standard plat count method

5


Reference Books :-

1. Water Supply & Sanitary Engg. - G.S. Birdie - Dhanpat Rai Publishing Company, 2. (P) Ltd. New Delhi3. Waste Water Engg. by B.C. Punmia - Laxmi Publication (P) Ltd. New Delhi4. Environmental Engg. - M.L. Davis & D.A. Cornwell - Mc Graw Hill Company5. Chemistry for Environmental Engg. - Sawyer & Mc Carty - Mc Graw Hill Book Company New Delhi6. Water & Waste Water Technology - Mark J Hammer - Prentice - Hall of India, New Delhi

7. Waste Water Engineering - Metcalf & Eddy - Mc Graw Hill Book Company New Delhi

6





DC-21

Geo-Technical Engg. - I

CE704 L T P Max.Marks-100Min.Marks-35 Duration-3hrs.

3 1 2

Branch: Civil Engineering-VII SemesterCourse: CE704 Geo-Technical Engg. - IUnit - IBasic Definitions & Index Properties: Definition and scope of soil mechanics, Historical development. Formation of soils. Soil composition. Minerals, Influence of clay minerals on engineering behaviour. Soil structure. Three phase system. Index properties and their determination. Consistency limits. Classification systems based on particle size and consistency limits.

Unit - IISoil Water and Consolidation: Soil water, Permaeability Determination of permeability in laboratory and in field. Seepage and seepage pressure. Flownets, uses of a flownet, Effective, neutral and total stresses.Compressibility and consolidation, Relationship between pressure and void ratio, Theory of one dimensional consolidation. Consolidation test, Fitting Time curves. Normally and over consolidated clays. Determination of preconsolidation pressure, settlement analysis. Calculation of total settlement.

Unit - IIIStress Distribution in Soils and Shear Strength of Soils: Stress distribution beneath loaded areas by Boussinesq and water gaurd’s analysis. Newmark’s influence chart. Contact pressure distribution.Mohr - Coulomb’s theory of shear failure of soils, Mohr’s stress circle, Measurement of shear strength, Shear box test, Triaxial compression test, unconfined compression test, Value shear test, Measurement of pore pressure, pore pressure parameters, critical void ratio, Liquefaction. Unit - IVStability of Slopes: Infinite and finite slopes. Types of slope failures, Rotational slips. Stability number. Effect of ground water. Selection of shear strength parameters in slope stability analysis. Analytical and graphical methods of stability analysis. Stability of Earth dams. Unit - VLateral Earth Pressure: Active, passive and earth pressure at rest. Rankine, Coulomb, Terzaghi and Culmann’s theories. Analytical and graphical methods of determination of earth pressures on cosion-less and cohesive soils. Effect of surcharge, water table and wallfriction. Arching in soils. Reinforced earth retaining walls.

LABORATORY WORK : Laboratory work will be based on the above course as required for soil investigators of engineering projects.

List of Experiments:1. Determination of Hygroscopic water content2. Particle - size analysis3. Determination of Specific gravity of soil particles4. Determination of plastic limit5. Determination of liquid limit6. Determination of shrinkage limit7. Permeability tests8. Direct shear test9. Consolidation test

7


Suggested Books: -

1. Soil Mech. & Found. Engg. by Dr. K.R. Arora - Std. Publishers Delhi.2. Soil Mech. & Found. by Dr. B.C.Punmia- Laxmi Publications, Delhi. 3. Modern Geotech Engg. by Dr.l Aram Singh - IBT Publishers, Delhi. 4. Geotech Engg. by C. Venkatramaiah - New Age International Publishers, Delhi 5. Soil Mech. & Found. Engg. by S.K. Garg- Khanna Publishers, Delhi. 6. Soil Testing for Engg. by T.W. Lambe - John Wiley & Soms. Inc.7. Relevant I.S. Codes

8





NECC-9

Minor Project

CE706 L T P Max.Marks-100Min.Marks-35 Duration-3hrs.

0 0 4

Branch: Civil Engineering-VII SemesterCourse: CE706 Minor Project

Each candidate shall work on an approved project of a public building or any other civil engineering work and shall submit design and a set of drawings.

ORShall submit a detailed report of experimental work/ software package on any specific problem of importance.

9


CE -7101 COMPUTATIONAL METHODS IN STRUCTURAL ENGINEERINGUnit - I.Matrix formulation for the principle of virtual work and energy principles, principle of contragradience, stiffness and flexibility matrices, Degree of Freedom. Axial, bending, shear and torsional deformations. Local and Global Element stiffness matrices for bar, beam, shaft, grid, shear wall, beam-column, beam with rigid ends, beam on elastic foundation and elements with special boundary conditions. nonprismatic and curved elements, forces and displacements in general coordinate axes, structure stiffness matrix.Unit - II. Basics of the Direct Stiffness method - Analysis of pinjointed frames, rigid jointed structures, plane grids and composite structures for different loads including temperature, shrinkage, prestressing forces. Elastic stability analysis of 2-D rigid jointed frames, (Sway & Nonsway) Unit - III. Concepts of Bandwidth, various storage schemes & equation solvers; Reduction in order of stiffness matrix - use of substructures, static condensation method, Exploiting symmetry, skew symmetry and cyclic symmetry in structures, Imposition of Constraints - Lagrange Multiplier and Penalty Methods.Unit - IV. Analysis of continuum structures - Fundamental equations of theory of elasticity (2D), basic concepts of Finite Element Analysis, derivation of generalised element stiffness matrix and load vectors, convergence requirements, stiffness matrices for various elements using shape functions, Triangular and Rectangular elements. (PSPS)Unit - V.Two Dimensional Iso parametric elements, shape functions for Simplex. Lagrangian and Serendipidity family elements in natural coordinates, computation of stiffness matrix for isoparametric elements, degrading of elements, plate bending elements.Reference Books :-

1. Ghali A & Neville M., Structural Analysis - A Unified Classical and Matrix Approach, Chapman and Hall, New York.

2. Weaver William & Gere James M., Matrix Analysis of Framed structures, CBS Publishers and Distributors, New Delhi.

3. Cook R.D., Concepts and Applications of Finite Element Analysis, Wiley, New York.

4. Gallagher R., Finite Element Analysis Fundamentals, Prentice-Hall, Englewood Cliffs, NJ.

5. Rubenstein M.F., Matrix Computer Analysis of structures, Prentice Hall, Englewood Cliffs, N.J.

6. Zeinkiewicz O.C & Taylor R.L., The Finite Element Method, McGraw Hill, London

10


CE -7102 TRAFFIC ENGINEERING Unit -I. Traffic Characteristics : (i) Road user’s characteristics - general human characteristics, physical, mental and emotional factors, factors affecting reaction time, PIEV theory. (ii) Vehicular characteristics: Characteristics affecting road design-width, height, length and other dimensions. weight, power, speed and braking capacity of a vehicle.Unit -II. Traffic Studies : (i) Spot Speed Studies and Volume Studies. (ii) Speed and Delay Studies-purpose, causes of delay, methods of conducting speed and delay studies. (iii) Origin and Destination Studies ( O & D) : Various methods, collection and interpretation of data, planning and sampling. (iv) Traffic Capacity Studies: Volume, density, basic practical and possible capacities, level of service. (v) Parking Studies: Methods of parking studies cordon counts, space inventories, parking practices.Unit -III. Traffic Operations and Control : (i) Traffic regulations and various means of control.(ii) One way streets- advantages and limitations. (iii) Traffic signals- isolated signals, coordinated signals, simultaneous, alternate, flexible and progressive signal systems. Types of traffic signals, fixed time signals, traffic actuated signals, speed control signals, pedestrian signals, flashing signals, clearance interval and problems on single isolated traffic signal.Unit -IV. Street Lighting : (i) Methods of light distribution. (ii) Design of street lighting system. (iii) Definitions- Luminaire, foot candle, Lumen, utilization and maintenance factors. (iv) Different types of light sources used for street lighting. (v) Fundamental factors of night vision.Unit -V. Accident Studies & Mass Transportation : (i) Accident Studies : Causes of accidents, accident studies and records, condition and collision diagram, preventive measures. (ii) Expressways and freeways, problems on mass transportation and remedial measures, brief study of mass transportation available in the country.

Reference Books :- 1. Traffic Engineering and Transport Planning by L.R. Kadiyali, Khanna Publishers, Delhi2. Traffic Engineering by Matson, W.S.Smith & F.W. Hurd3. G.J. Pingnataro, Principles of Traffic Engineering4. D.R.Drew, Traffic Flaw Theory5. W.R. Mchsne and R.P. Roess "Traffic Engg"6. Wohl & Martin, Traffic System Analysis for Engineering & Planners

11


CE- 7103 INDUSTRIAL WASTE TREATMENT Unit - I.Problem of Water Pollution: Effects of wastes on streams and sewage treatment plant. natural purification of streams. oxygen sag curve. allowable organic load on streams classification of stream, stream standards and effluent standards. requirement of water for different purposes.Unit - II.Measurement of Waste Water Volume: Sampling of waste waters, grab and composite samples. analysis of waste water. biochemical oxygen demand. chemical oxygen demand and pH value of waste, toxicity of waste by bioassay method. Pretreatment of Wastes: Volume and strength reduction, salvage of materials, recovery of by products, reuse of waste water.Unit - III. Conventional Methods of Treatment of Waste Water: Removal of suspended solids, removal of inorganic and organic dissolved solids, studge disposal, advance methods of treatment, such as reverse osmosis, ion exchange, electrodialysis, algal harvesting etc. low cost treatment plants. common effluent treatment plant, design and operation.Unit - IV. Combined Treatment of Waste Water Sewage: Energy requirement optimization and bedget, municipal regulation, sewer rental charge, instrumentation in waste water treatment plants, collection of data, operation and maintenance of plants, water pollution control board.Unit - V.Brief study of industrial processes and treatment methods of waste water from common industries, such as textile, dairy, paper and pulp, tannery, distillery.Hazardeous wastes- Impact handing and disposal. Reference Books :-

1. "Liquid Waste of Industries - Theories, Practice and Treatment" - N.L. Nemerow, WEsley Publishing Co.

2. Treatment of Industrial Waste - E.B. Besselievre & Max Schwartz - Mc Graw Hill Book Company

3. "Waste Water Engg. - Treatment Disposal & Reuse" - Metcalf & Eddy - Tata Mc Graw Will, New Delhi

4. Waste Water Treatment - Arceivala - Tata Mc Graw Will, New Delhi5. Industrial Pollution Control, hand book - Lund H.F. Tata Mc Graw Will, New Delhi

12


CE-7104 COST EFFECTIVE & ECO-FRIENDLYCONSTRUCTION UNIT-I

Concepts of energy efficient & environment friendly materials and techniques.

Cost effective materials :- Soil, Fly ash, Ferrocement, Lime, Fibres, Stone Dust, Red mud, Gypsum, Alternate Wood, Polymer.

Energy Efficient & Environment friendly building material products :-

Walls - Stabilised and sun dried, soil blocks & bricks, Solid & Hollow concrete blocks, stone masonry blocks, Ferrocement partitions.Roofs - Precast R.C. Plank & Joists roof, Precast channel roof, Precast L-panel roof, Precast Funicular shells, Ferrocement shells, Filler Slab, Seasal Fibre roof, Improved country tiles, Thatch roof, M.C.R. tile.

UNIT-II Cost effective construction techniques and equipments :- (a) Techniques :- Rat trap bond construction, Energy Efficient roofings, Ferrocement technique, Mud

Technology.(b) Equipments :- Brick moulding machine, Stablilised soil block making machine and plants for the

manufacturing of concrete blocks, M.C.R. tile making machine, Ferrocement wall panel & Roofing channel making machine, R.C.C. Chaukhat making m/c.

UNIT-III Cost effective sanitation :-

(a) Waste water disposal system (b) Cost effective sanitation for rural and urban areas

(c) Ferrocement Drains

UNIT-IV Low Cost Road Construction :-Cost effective road materials, stabilization, construction techniques tests, equipment used for

construction, drainage, maintenance.

UNIT-VCost analysis and comparison :-(a) All experimental materials (b) All experimental techniques

\

13


CE-7105 ENVIRONMENTAL IMPACT ASSESSMENT

UNIT-IConcept of EIA : Introduction of EIA, Utility and scope of EIA, Significant Environmental Impacts, Stage of EIA, Environmental Inventory, Environmental Impact Statement (EIS)

UNIT-IIMethods of Impact Identification : Environmental Indices and indicators for describing the affected environment, matrix methodologies, network, checklist, and other method.

UNIT-III Impact analysis : Framework, statement predication and assessment of impact of air, water, noise and socio-economic environment.

UNIT-IV Preparation of written documentation : Initial planning phase, detailed planning phase, writing phase, organizing relevant information, co-ordination of team writing effort.

UNIT-V

Public Participation in Environmental Decision making : Basic definitions, Regulatory requirements, Advantages & disadvantages of Public Participation, Selection of Public participation techniques, Practical considerations for implementation.

14


Course of Study and Scheme of Examination B.E. Civil Engineering (New)

SEMESTER – VIII S.No Course

Category Course Code (New) Subject Period Per Week Distribution of Marks

Theory Exam

Practical Exam

Internal Assessment

Total

MST TW L T P C I II III Total I+II+III

1. DC-24 CE-801 Geo. Technical Engg. II 3 1 2 6 100 50 20 30 50 200

2. DC-25 CE-802 Construction Planning & Management 3 1 0 4 100 - 20 - 20 120

3. DC-26 CE-803 Advanced Structural Design-II (Steel) 3 1 2 6 100 50 20 30 50 200

4. DC-27 Refer Table Below Elective –II 3 1 0 4 100 - 20 - 20 120

5. DC-28 CE-805 Major Project 0 0 8 8 - 150 - 110 110 260 6. NECC-11 CE-806 General Proficiency 0 0 4 4 - 50 - 50 50 100

Total 12 4 16 32 400 300 80 220 300 1000 Minimum Pass Marks Duration (A) Theory : 35 Percent (C) Duration of Theory Paper 3 hrs. (B) Practical : 50 Percent Elective - II : CE-8201 Structural Dynamics & Earthquake Engineering

CE-8202 Pavement Design CE-8203 Air Quality Monitoring & Control CE-8204 Energy Efficient & Green Building CE-8205 Design of Prestrassed Conc. Structure CE-8206 Water Power Engineering CE-8207 Advance Water Resources Energy

14


Course of Study and Scheme of Examination B.E. Civil Engineering (New)

SEMESTER – VIII S.No Course

Category Course Code (New) Subject Period Per Week Distribution of Marks

Theory Exam

Practical Exam

Internal Assessment

Total

MST TW L T P C I II III Total I+II+III

1. DC-24 CE-801 Geo. Technical Engg. II 3 1 2 6 100 50 20 30 50 200

2. DC-25 CE-802 Construction Planning & Management 3 1 0 4 100 - 20 - 20 120

3. DC-26 CE-803 Advanced Structural Design-II (Steel) 3 1 2 6 100 50 20 30 50 200

4. DC-27 Refer Table Below Elective –II 3 1 0 4 100 - 20 - 20 120

5. DC-28 CE-805 Major Project 0 0 8 8 - 150 - 110 110 260 6. NECC-11 CE-806 General Proficiency 0 0 4 4 - 50 - 50 50 100

Total 12 4 16 32 400 300 80 220 300 1000 Minimum Pass Marks Duration (A) Theory : 35 Percent (C) Duration of Theory Paper 3 hrs. (B) Practical : 50 Percent Elective - II : CE-8201 Structural Dynamics & Earthquake Engineering

CE-8202 Pavement Design CE-8203 Air Quality Monitoring & Control CE-8204 Energy Efficient & Green Building CE-8205 Design of Prestrassed Conc. Structure CE-8206 Water Power Engineering CE-8207 Advance Water Resources Energy

15



CourseCourse Title Course Code Credits-6C Theory Papers (ES)


DC-24

Geo Tech. Engg. - II


3 1 2

Branch: Civil Engineering-VIII Semester Course: CE801 Geo Tech. Engg. - II Unit - I Shallow Foundations : Type of foundations shallow and deep. Bearing capacity of foundation on cohesion less and cohesive soils. General and local shear failures. Factors effecting B.C. Theories of bearing capacity - Prandle, Terzaghi, Balla, Skempton, Meyerh of and Hansan. I.S. code on B.c. Determination of bearing capacity. Limits of total and differential settlements. Plate load test. Unit - II Deep Foundation : Pile foundation, Types of piles, estimation of individual and group capacity of piles in cohesion less and cohesive soils. Static and dynamic formulae.. Pile load test, Settlement of pile group, Negative skin friction, under- reamed piles and their design. Piles under tension, inclined and lateral load Caissons. Well foundation. Equilibrium of wells. Analysis for stability tilts and shifts, remedial measures. Unit - III Soil Improvement Techniques : Compaction. Field and laboratory methods, Proctor compaction tests, Factors affecting compaction. Properties of soil affected by compaction. Various equipment for field compaction and their suitability. Field compaction control. Lift thickness. Soil stabilisation : Mechanical, Lime, Cement, Bitumen, Chemical, Thermal, Electrical-stabilisation and sabilisation by grouting. Geo-synthetics, types, functions, materials and uses. Unit - IV Soil Exploration and Foundations on Expansive and Collapsible soils : Methods of soil exploration. Planning of exploration programme for buildings, highways and earth dams. Disturbed and undisturbed samples and samplers for collecting them. Characteristics of expansive and collapsible soils, their treatment, Construction techniques on expansive and collapsible soils. CNS layer. Unit - V Sheet piles/Bulkheads and Machine foundation : Classification of sheet piles/bulkheads. Cantilever and anchored sheet piles, Cofferdams, materials, types and applications. Modes of vibration. Mass-spring analogy, Natural frequency. Effect of vibration on soils. Vibration isolation. Criteria for design. Design of block foundation for impact type of machine. LABORATORY WORK: Laboratory work will be based on the course of Geotech. Engg. I & II as required for soil investigations of engineering projects and not covered in the lab. Work of Geotech. Engg. I.

16


LIST OF EXPERIMENTS 1. Indian Standard Light Compaction Test/Std. Proctor Test 2. Indian Standard Heavy Compaction Test/Modified Proctor Test 3. Determination of field density by Core Cutter Method4. Determination of field density by Sand Replacement Method5. Determination of field density by Water Displacement Method 6. The corifiled Compression Test 7. Triaxial compression test8. Lab. Vane Shear test 9. CBR Test10. Demonstration of

Plate Load Test SPT & DCPT

Reference Books :-- 1. Soil Mechanics & Foundation Engg. by Dr. K.R. Arora - Std. Publishers Delhi 2. Soil Mechanics & Foundation Engg. by B.C. Punmia - Laxmi Publiscations Delhi 3. Modern Geotech. Engg. by Dr. Alam Singh-IBT Publishers Delhi. 4. Geotech. Engg. by C.Venkatramaiah-New AGe International Publishers, Delhi 5. Found. Engg. by GALeonards McGraw Hill Book Co. Inc. 6. Relevant IS Code

17





DC-25

Construction Planning & Management


3 1 0

Branch: Civil Engineering-VIII Semester Course: CE802 Construction Planning & Management

Unit -I Preliminary and detailed investigation methods: Methods of construction, form work and centering. Schedule of construction, job layout, principles of construction management, modern management techniques like CPM/PERT with network analysis. Unit -II Construction equipments: Factors affecting selection, investment and operating cost, output of various equipments, brief study of equipments required for various jobs such as earth work, dredging, conveyance, concreting, hoisting, pile driving, compaction and grouting. Unit -III Contracts: Different types of controls, notice inviting tenders, contract document, departmental method of construction, rate list, security deposit and earnest money, conditions of contract, arbitration, administrative approval, technical sanction. Unit -IV Specifications & Public Works Accounts: Importance, types of specifications, specifications for various trades of engineering works. Various forms used in construction works, measurement book, cash book, materials at site account, imprest account, tools and plants, various types of running bills, secured advance, final bill. Unit-V Site Organization & Systems Approach to Planning: Accommodation of site staff, contractor’s staff, various organization charts and manuals, personnel in construction, welfare facilities, labour laws and human relations, safety engineering.Problem of equipment management, assignment model, transportation model and waiting line modals with their applications, shovel truck performance with waiting line method. Reference Books :-

1. Construction Equipment by Peurify 2. CPM by L.S. Srinath 3. Construction Management by S. Seetharaman 4. CPM & PERT by Weist & Levy 5. Construction, Management & Accounts by Harpal Singh6. Tendering & Contracts by T.A. Talpasai

18





DC-26

Advanced Structural Design-II (Steel)


3 1 2

Branch: Civil Engineering-VIII Semester Course: CE803 Advanced Structural Design- II (Steel)

Unit – I Plate girder bridges (Riveted and welded) Unit – II Trussed girder bridges for railways and highways (IRC & IRS holding). Bearings for bridges. Unit – III Water Tanks: Pressed steel tanks, tanks with ordinary plates, square, rectangular, circular with hemispherical bottom and conical bottom. Unit - IV Chimneys: Guyed and self supporting steel stacks.Unit – V Bunkers, Silos & Towers Reference Books :- 1. Design of Steel Structures – Ramammutham 2. Design of Steel Structures – Punia 3. Steel Str. by Ramchandra Vol II 4. Steel Str. by Arya & Ajmani 5. Design of steel structures – L.S. Negi

19





DC-28

Major Project - I


0 0 8

Branch: Civil Engineering-VIII Semester Course: CE805 Major Project - I

Each candidate shall work on an approved Civil Engg. Project and shall submit design and a set of drawings on the project.

20


CE-8201 STRUCTURAL DYNAMICS & EARTHQUAKE ENGINEERING Unit - I. Single DOF systems - Undamped and Damped, Response to Harmonic and periodic excitations, Response to Arbitrary, Step, Ramp and Pulse Excitations. Unit - II. Numerical Evaluation of Dynamic Response - Time stepping methods, methods based an Interpolation of Excitation, Newmark’s and Wilson - q method, Analysis of Nonlinear Response, Introduction to frequency domain analysis. Unit - III. Elements of seismology - Definitions of the basic terms related to earthquake (magnitude, intensity, epicenter, focus etc.), seismographs Earthquake Response of structures - Nature of dynamic loading resulting from earthquake, construction of Response spectrum for Elastic and Inelastic systems. Unit - IV. Multiple DOF systems : Stiffness and Flexibility matrices for shear buildings, free and forced vibrations-undamped and damped, Modal and Response History Analysis, Systems with distributed mass & elasticity. Unit - V. Earthquake Resistant Design of Structures, Design of structures for strength & servicability, Ductility and energy absorption, Provisions of IS : 1893 and IS : 4326 for aseismic design of structures, Code for ductile detailing IS : 13920. Reference Books :-- 1. Chopra A.K., Dynamics of structures - Theory and Applications to Earthquake Enginering,Prentice Hall of

India, New Delhi. 2. Berg G.V. Elements of Structural Dynamics, Prentice Hall of India, Englewood Cliffs, NJ 3. Paz Mario, Structural Dynamics, CBS Publishers, Delhi4. Clough R.W. & Penzien J., Dynamics of structures McGraw Hill, New York.

21


CE-8202 PAVEMENT DESIGN Unit -I. Equivalent Single Wheel Load (ESWL) : Definition, calculation of ESWL, repetition of loads and their effects on the pavement structures. Unit -II. Flexible Pavements : Component parts of the pavement structures and their functions, stresses in flexible pavements, Stress distribution through various layers, Boussinesque’s theory , Burmister’s two layered theory, methods of design, group index method, CBR method, Burmister’s method and North Dakota cone method. Unit -III. Rigid Pavements : Evaluation of subgrade, Modulus-K by plate bearing test and the test details, Westergaard’s stress theory stresses in rigid pavements, Temperature stresses, warping stresses, frictional stresses, critical combination of stresses, critical loading positions.Unit -IV. Rigid pavement design : IRC method, Fatigue analysis, PCA chart method, joints, design and construction & types, AASHTO Method, Reliability analysis.Unit -V. Evaluation and Strengthening of Existing Pavements : Benkleman beam method, Serviceability Index Method. Rigid and flexible overlays and their design procedures. Reference Books :--

1. Principles of pavement design by E.J.Yoder & M.W. Witczak 2. AASHO, “AASHO Interim Guide for Design of Pavement Structures”, Washington, D.C. 3. Portland Cement Association, Guidlines for Design of Rigid Pavements, Washington 4. DSIR, Conc. Roads Design & Construction5. Srinivasan M. "Modern Permanent Way"

22


CE-8203 AIR QUALITY MONITORING & CONTROL Unit - I Air pollution problem: Economics and social aspects, historical episodes of air pollution. Sources of Air pollution, effects of air pollution on health, animal, plants and materials Unit - II Role of meteorological condition, properties of typical air pollutants, air diffusion and concentration pollutants. general diseases caused by air pollutants. toxicity of various pollutants. Plums patterns and height of chimneys. Unit - III Atmospheric chemistry, formation of secondary pollutants – PNN, PBN, Photolytic cycles, general diseases and toxicity of pollutants Unit - IV Sampling and Analyzing of Air Pollutants: Instruments pollution survey, standards of air pollution. Principle of air pollution control, site selection and zoning, various control methods, process and equipment changes, design and operation of various air pollution control equipments. Unit - V Air pollution control legislation, public education pollution standards, status of air pollution control in various countries. Industrial Hygiene: Concept and importance, factory Involved in environmental hazards, industrial ventilation occupational diseases, control methods. Reference Books :-- 1. "Air Pollution" - Faith W.L, John Wiley & Sons 2. "Air Pollution" - Mc Cabe L.C., Mc. Graw Hill, International 3. Air Pollution - Stern A.C., Academic Press N. York4. Fundamentals of Air Pollutions - Raju BSN Oxford & IBH Publishing Co. Pvt. Ltd. 5. "Air Pollution" - Rao M.N. & Rao HVN - Tata Mc Graw Hill 6. Air Pollution – Wark and Warner

23


CE-8207 ADVANCE WATER RESOURCES ENGINEERING.

Unit-I

Hydrology : Hydrological cycle, precipitation and its measurement, recording and non recording rain gauges, estimating missing rainfall data, rain gauge net works, mean depth of precipitation over a drainage area, mass rainfall curves, intensity-duration curves, depth-area duration curves,

Unit-II

Hydrology :Infiltration and infiltration indices, evaporation stream gauging, run off and its estimation, hydrograph analysis, unit hydrograph and its derivation from isolated and complex storms, S-curve hydrograph, synthetic unit hydrograph.

Unit-III

Floods : Types of floods and their estimation by different methods, probability and frequency analysis, flood routing through reservoirs and channels, flood control measures, economics of flood control.

Unit-IV

Ground water : Occurrence, confined and unconfined aquifers, aquifer properties, hydraulics of wells under steady flow conditions, infiltration galleries. Ground water recharge-necessity and methods of improving ground water storage.

Water logging and salt efflorescence : Water logging-causes, effects and its prevention. Salt efflorescence-causes and effects. reclamation of water logged and salt affected lands.

Unit-V

Water resources planning and management : Planning of water resources projects, data requirements, economic analysis of water resources projects appraisal of multipurpose projects, optimal operation of projects-introduction to linear programming and its application to water resources projects. Role of water in the environment, rain water harvesting, impact assessment of water resources development and managerial measures. Suggested Books :- 1. Engg. Hydrology - J.NEMEC - Prentice Hall 2. Hydrology for Engineers Linsley, Kohler, Paulnus - Tata Mc.Graw Hill. 3. Engg. Hydrology by K. Subhramanya - Tata Mc Graw Hills Publ. Co.4. Hydrology & Flood Control by Santosh Kumar - Khanna Publishers 5. Engg. Hydrology by H.M. Raghunath

Date post:	09-Mar-2018
Category:	Documents
Upload:	lythuy
View:	229 times
Download:	1 times

Course Contents - VNS Civil.pdf · Course Contents Category of ... Definition and scope of soil...

Documents