Terex® Minerals Processing SystemsCedarapids CRC450X

CRC450X PORTABLE CONE PLANT

Form 25849 (8/12)

Oversized quick release cone surge hopperCrusher overflow chute to undercrusher conveyor*Longer undercrusher conveyor with hydraulic adjust discharge;

42" x 45' (1067 x 13,716 mm); 15 hp (11 kW) *Feed conveyor with hydraulic positioning (LH or RH);

36" x 36' (914 x 10,973 mm); 15 hp (11 kW) Conveyor skirt boards

*Requires hydraulic leveling or run-on jacks option

Removable electrical switchgear panel with crusher soft start and push-button station

Hydraulic leveling or run-on jacks (gas, 12V or 24V powered)Power cables and quick disconnectsOversize 315/80 R22.5 tiresDust suppression water spray systemFlexco style belt wiper

High efficiency MVP450X cone crusher with ElJay® Rollercone® roller bearing construction

Single 400 hp (296 kW) crusher motor with easy adjust cone crusher drive

Mesh cone hopper extension“Straight-line” undercrusher conveyor; 42" x 34'6"

(1067 x 10,515 mm); 15 hp (11 kW) 3-ply conveyor belt with vulcanized belt spliceService platforms around crusher with guard rails and

access ladder

OPTiONAL EquiPMENT

STANdARd FEATuRESEasy maintenance features •Ratchetconedrivebelttensioning •Convenientlylocatedgreasebanks •Groundaccessconelubricationmodule •LargeundercrusherhingedaccesspanelEmergency stop buttons on both sides of frameTriple axle spring suspensionDrop-down rear stabilizing legsTwelve 295/75 R22.5 tiresLockable 4' (102 mm) long side-mounted storage box

Unit shown with the following options: right-hand feed conveyor; 45' (13,716 mm) undercrusher conveyor; oversized quick release cone surge hopper and overflow chute; electrical panel; hydraulic run-on jacks; conveyor skirt boards and belt wipers.

http://www.terex.com/minerals-processing-systems/en/products/new-equipment/portable-plants/cone-plants/cedarapids-crc450x/index.htm

Terex® Minerals Processing SystemsCedarapids CRC450X Portable Cone Plant

SPECiFiCATiONS

Effective Date: August 2012. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings inthis document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. © 2012 Terex Corporation.

Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USATel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com

www.terexmps.com

Form 25849 (8/12)

Transport Position - Unit shown with the standard 34'6" (10,515 mm) undercrusher conveyor. Options shown: oversized quick release cone surge hopper and overflow chute, belt wiper, electrical panel and hydraulic run-on jacks. Total Weight: 92,697 lbs (42,048 kg); Kingpin: 45,587 lbs (20,678 kg); Rear Axle: 47,110 lbs (21,370 kg); Weights include the options shown.

Transport Position - Unit shown with the following options: left-hand feed conveyor, 45' (13,716 mm) undercrusher conveyor, oversized quick release cone surge hopper and overflow chute, electrical panel, hydraulic run-on jacks, conveyor skirt boards and belt wipers. Total Weight: 103,628 lbs (47,006 kg); Kingpin: 45,563 lbs (20,667 kg); Rear Axle: 58,065 lbs (26,339 kg); Weights include the options shown.

Operating Position - Unit shown with the following options: left-hand feed conveyor (right-hand feed conveyor also available), 45' (13,716 mm) undercrusher conveyor with skirt boards, belt wipers, oversized cone surge hopper and overflow chute, electrical panel and hydraulic run-on jacks.

13'5"(4089)

5'8"(1727)

5'9"(1753)

8' (2438)Axle Track

11'5" (3480)

4' (1219)

19"(483)

11" (279)

12'6" (3810)

38'11" (11,862)

21'7" (6579)4'10"(1473)

7'2"(2184)

9'6"(2896)

10°

4'10"(1473)

6'3"(1905)

5'9"(1753)

11'11" (3632)12'6" (3810)

2'5"(736)

12'9"(3886)

4'10"(1473)

4'10"(1473)

21'7" (6579)38'11" (11,862)

13'5"(4089)

4' (1219)

19"(483)

11" (279)

16'1" (4902)8' (2438)

15'1" (4597)16'11" (5156)11" (279)10'1" (3073)

11'7" (3530) @ 13.8°15'8" (4775) @ 20°

13.8°to 20°

Optional electrical panelmust be set on groundduring operation.

7'5" (2260) to9'9" (2972)

6'4"(1930)

2'1" (635)

15'6" (4724)

Terex® Minerals Processing SystemsCedarapids CRC380X

CRC380X PORTABLE CONE PLANT

Form 25848 (8/12)

Oversized quick release cone surge hopperCrusher overflow chute to undercrusher conveyor*Longer undercrusher conveyor with hydraulic adjust discharge;

42" x 45' (1067 x 13,716 mm); 15 hp (11 kW) *Feed conveyor with hydraulic positioning (LH or RH);

36" x 36' (914 x 10,973 mm); 15 hp (11 kW) Triple axle spring suspension with drop-down rear stabilizing legsConveyor skirt boards

*Requires triple axle option and hydraulic leveling or run-on jacks option

Removable electrical switchgear panel with crusher soft start and push-button station

Hydraulic leveling or run-on jacks (gas, 12V or 24V powered)Power cables and quick disconnectsOversize 315/80 R22.5 tiresDust suppression water spray systemFlexco style belt wiper

High efficiency MVP380X cone crusher with ElJay® Rollercone® roller bearing construction

Single 300 hp (224 kW) crusher motor with easy adjust cone crusher drive

Mesh cone hopper extension“Straight-line” undercrusher conveyor; 42" x 34'6"

(1067 x 10,515 mm); 15 hp (11 kW) 3-ply conveyor belt with vulcanized belt spliceService platforms around crusher with guard rails and

access ladder

OPTiONAL EquiPMENT

STANdARd FEATuRESEasy maintenance features •Ratchetconedrivebelttensioning •Convenientlylocatedgreasebanks •Groundaccessconelubricationmodule •LargeundercrusherhingedaccesspanelEmergency stop buttons on both sides of frameTandem axle spring suspensionEight 295/75 R22.5 tiresLockable 4' (102 mm) long side-mounted storage box

Unit shown with the following options: left-hand feed conveyor; 45' (13,716 mm) undercrusher conveyor with skirt boards; belt wipers; oversized quick release cone surge hopper and overflow chute; electrical panel; triple axle; and hydraulic run-on jacks.

http://www.terex.com/minerals-processing-systems/en/products/new-equipment/portable-plants/cone-plants/cedarapids-crc380x/index.htm

Terex® Minerals Processing SystemsCedarapids CRC380X Portable Cone Plant

SPECiFiCATiONS

Effective Date: August 2012. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings inthis document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. © 2012 Terex Corporation.

Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USATel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com

www.terexmps.com

Form 25848 (8/12)

Transport Position - Unit shown with the standard 34' 6" (10,515 mm) undercrusher conveyor and dual axle.Options shown: oversized quick release cone surge hopper and overflow chute, belt wiper, electrical panel and hydraulic run-on jacks. Total Weight: 79,047 lbs (35,856 kg); Kingpin: 41,614 lbs (18,876 kg); Rear Axle: 37,433 lbs (16,980 kg); Weights include the options shown.

Transport Position - Unit shown with the following options: left-hand feed conveyor, 45' (13,716 mm) undercrusher conveyor, triple axle, oversized quick release cone surge hopper and overflow chute, electrical panel, hydraulic run-on jacks, conveyor skirt boards and belt wipers.Total Weight: 93,152 lbs (42,254 kg); Kingpin: 39,848 lbs (18,075 kg); Rear Axle: 53,304 lbs (24,179 kg); Weights include the options shown.

Operating Position - Unit shown with the following options: left-hand feed conveyor (right-hand feed conveyor also available), triple axle, 45' (13,716 mm) undercrusher conveyor, belt wipers, oversized cone surge hopper and overflow chute, electrical panel and hydraulic run-on jacks.

13'1"(3988)

5'8"(1727)

5'9"(1753)

6'6" (1981)Axle Track

11'5" (3480)

4' (1219)

19"(483)

11" (279)

12'6" (3810)

40'8" (12,395)

25'9" (7849)4'10" (1473)

7'10"(2388)

9'6"(2896)

10°

15'1" (4597)16'11" (5156)11" (279)10'1" (3073)

11'7" (3530) @ 13.8°15'8" (4775) @ 20°

13.8°to 20°

Optional electrical panelmust be set on groundduring operation.

7'5" (2260) to9'9" (2972)

6'4"(1930)

2'1" (635)

15'6" (4724)

6'3"(1905)

5'9"(1753)

12'6" (3810)2'5"

(736)

12'9"(3886)

4'10"(1473)

4'10"(1473)

21'7" (6579)38'11" (11,862)

13'1"(3988)

4' (1219)

19"(483)

11" (279)

16'1" (4902)8' (2438)11'11" (3632)

High Performance Closed Circuit Plant Featuring the High Lift Screen (HLS) System

Removable electrical switchgear panel with push button controls or remote with 150' (45 m) tether3+1 axle configuration (triple with pivot tag axle)12V, 24V hydraulic unitsDust suppression systemLJ-TSV6203 screen mounted at 2.5° (springs remove to reduce

travel height)

Heavy-duty hydraulic run-on jacksZero speed sensorsFeed conveyor skirtboard extensionsExtra off plant motor starters and controls (with panel option)Power cable and quick disconnectsCable management systemSelf-cleaning, twin pole feed conveyor magnet

High efficiency MVP380X 300 hp (224 kW) cone crusher with ElJay® Rollercone® roller bearing construction

LJ-TSV6203 triple shaft high g-force 3-deck screenPatent pending High Lift Screen (HLS) system maximizes cone

production and provides easy cone manganese accessMulti-position screen platform (operation, maintenance, travel)

around three sides of screen; platform access provided by a fixed incline ladder with handrails

Oversize, quick-release cone surge hopper and overflow chute buffers feed variations

Drop style main frame for easy cone access and high performance belt drive42" (1067 mm) wide, 25 hp (18.6 kW) wrap drive, main

feed conveyor42" (1067 mm) wide, 10 hp (7.5 kW) straight-line undercrusher

conveyor with hydraulic lowered tail section

42" (1067 mm) wide, 7.5 hp (5.6 kW) underscreen fines conveyor with primary style belt wiper

Two 30" (762 mm) wide, 7.5 hp (5.6 kW) reversible cross conveyors discharge 41" (1041 mm) beyond frame

All conveyor belts are 3-ply with vulcanized belt splices4-section, 3-position blending system to mix second and bottom deck overs36" (914 mm) wide, 7.5 hp (5.6 kW) reversible closed circuit

transfer conveyorQuad axle suspensionOn-board gas powered hydraulics to run screen support, jacks

and undercrusher tail dropHydraulic leveling jacks with front and rear support legsMany easy maintenance features including convenient grease

banks, ratchet cone drive adjustment, cartridge X-belt flashingSide mounted lockable storage box

OPtiOnaL EquiPmEnt

Standard FEaturES

terex® minerals Processing SystemsCedarapids CrC380XHLS

CrC380XHLS POrtaBLE COnE/SCrEEn PLant

Form 25505 (7/13)

http://www.terex.com/minerals-processing-systems/en/products/new-equipment/portable-plants/cone-plants/cedarapids-crc380xhls/index.htm

terex® minerals Processing SystemsCedarapids CrC380XHLS Portable Cone/Screen Plant

SPECiFiCatiOnS

Effective Date: July 2013. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied.Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex and Cedarapids are registered trademarks of Terex Corporation in the USA and many other countries. © 2013 Terex Corporation.

Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USATel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com

www.terexmps.com

Form 25505 (7/13)

Quad (4-Axle) Configuration Kingpin Weight: 60,800 lbs (27,580 kg); Total Weight: 138,300 lbs (62,735 kg) 3+1 Axle Configuration Kingpin Weight: 62,800 lbs (28,485 kg); Total Weight: 142,100 lbs (64,455 kg)

Note: Weights are approximate and include run-on jacks and switchgear.

69'10" (21,285)

5'1"(1549) 15'7" (4750) 14' (4267)

6'11"(2108) 17'7" (5359) 10'8" (3251)

13" (330) MaximumJack Lift

42" (1067) Overhead Conveyorwith 25 hp (18.5 kW) motor

MVP380X ElJay® Rollercone® Crusher

Power Panel (optional)

LJ-TSV 6203-32 Screen

Note: All operational dimensions are shown with jack legs fully extended.

7'4"(2235)

18"(457)

8'(2438)

Operating Mode42" (1067) Underscreen Conveyor with 7.5 hp (5.6 kW) motor

30" (762) Cross Conveyors with 7.5 hp (5.6 kW) motor60" (1524) and 90" (2286) Ground Clearance

6" x 24" (152 x 609) Stroke Run-On Jacks (optional)

42" (1067) Undercrusher Conveyor with 10 hp (7.5 kW) motor

36" (914) Transfer Conveyor with 7.5 hp (5.6 kW) motor

Operating Height 19'3" (5867)

Optional 3+1 axle

4'10"(1473)

4'10"(1473)

16'2" (4928) 25"(635)

41'11" (12,776) to Kingpin74'4" (22,657) Overall Length

59,300 lbs (26,900 kg) 20,000 lbs (9070 kg)

Transport ModeTransport Height 13'11" (4242)

4'2" (1270)

70'3" (21,412)

4'7"(1397)

8'4"(2540)

4'10"(1473)

4'10"(1473)

Transport Width 11'11" (3632)

77,500 lbs (35,155 kg)

4'10"(1473)

4'(1219)

12" (305) 15" (381)

43' (13,106)

Terex® Minerals Processing SystemsCedarapids CRJ3054

Removable electrical switchgear panel, wiring and operator push-button station, manual ratchet panel lift system

Hydraulic lift system for switchgear panelTethered remote feeder controlQuick disconnect power cablesHinged, 30" (762 mm) hopper extensions with locking supports

accessible from the ground, available with hydraulic operation24' (7315 mm) long feeder/hopper (versus 20')Rock breaker with tethered remote and single point lubricationGrizzly reject cross conveyor

Various grizzly bar spacingTwo-piece drop-on side bulkheadsHydraulic undercrusher conveyor tail lift systemExtended length undercrusher conveyor with hydraulic foldDust suppression water spray systemCross belt self-cleaning magnetBelt scale Hydraulic leveling/run-on jacks (gas, 12V, or 24V in hinged enclosure)Triple axles or 3+1 axles (triple + tag)Oversize 315/80 R22.5 tires

JS3054 Jaw Crusher Easy removal jaw die wedge systemQuick adjust jaw settings • Integrated hydraulic assist shim system • Hydraulic release toggle seatDrop-forged heat-treated 4340 chrome-nickel-steel eccentric shaft • Enlarged diameter with compound geometry200 hp (149 kW), 1200 rpm electric crusher drive motorPivoting motor base with tool-free ratchet drive adjustment system

5220-15 Vibrating Grizzly Feeder Removable hopper module with 3/4" (19 mm) AR 400 sidesAdjustable action vibrator unit with pivot base motor mountingHeavy coil springs with removable spring bracketsSix sloped bolt-in grizzly bars with 4" (102 mm) nominal openingBypass chute diverts grizzly fines to undercrusher conveyorRubber side curtains

Undercrusher ConveyorTail section lowers for operation, raises for transport via manual ratchetStraight-line conveyor designAdjustable discharge heightShaft mount gear box and TEFC motorImpact bars under jaw and grizzly bypass3-ply conveyor belt with vulcanized splice

Main Frame with Quad AxleStraight beam chassis with kingpin, under-frame mounted axles,

spring suspension, air brakes, travel lights and splash guards Jaw mount vibration isolation padsEmergency stops on both sides of chassisSixteen 295/75 R22.5 tiresAdjustable kingpin support legsService and observation platforms with fold-down hand railsRemote grease linesLockable side-mounted storage box

CRJ3054 PORTABLE JAW PRIMARY PLANT

OPTIONAL EQUIPMENT

STANdARd FEATURES

Form 25732 (5/13)

http://www.terex.com/minerals-processing-systems/en/products/new-equipment/portable-plants/jaw-plants/crj3054-plant/index.htm

8’-10”Lowers to

7’-0”

Jaw Crusher .............................................................30" x 54" (762 x 1371 mm) operating speed .................................................................................... 250 rpmUndercrusher conveyor ................................................................ 54" (1372 mm) operating speed .................................................................................... 350 fpmCross conveyor (optional) .............................................................30" (762 mm)Feeder ..................................................................... 52" x 20' (1321 x 6096 mm) operating speed .................................................variable speed 600-800 rpmBolted bar grizzly ............. 60" (1524 mm) long x 4" (102 mm) avg. opening AR pan liners ................................................................................1/2" (12.7 mm)Horsepower Jaw ............................................................................................... 200 (149 kW) Feeder ...............................................................................................40 (30 kW) Undercrusher conveyor ..................................................................20 (15 kW) Extended undercrusher conveyor (optional) .............................20 (15 kW) Cross conveyor (optional) .............................................................. 5 (3.7 kW) Self-cleaning magnet (optional) ................................................... 1.5 (1 kW) Dust suppression pump (optional) ............................................. 3/4 (.5 kW)

Tires ..................................................................................... Sixteen 295/75 R22.5 Estimated weight of plant with hopper module* Rear axle .......................................................................75,100 lbs (34,065 kg) Kingpin ...........................................................................47,200 lbs (21,410 kg) Total .............................................................................122,300 lbs (55,475 kg)Estimated weight of plant without hopper module* Rear axle ......................................................................49,800 lbs (22,590 kg) Kingpin ......................................................................... 45,450 lbs (20,615 kg) Total .............................................................................. 95,250 lbs (43,205 kg)Estimated weight of hopper module ............................ 27,050 lbs (12,270 kg)

* Weights include optional switchgear, jacks and hydraulics. Contact factory for weights of other optional equipment.

Transport

Operational

Terex® Minerals Processing SystemsCedarapids CRJ3054 Portable Jaw Primary Plant

SPECIFICATIONS

Effective Date: May 2013. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied.Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex and Cedarapids are registered trademarks of Terex Corporation in the USA and many other countries. © 2013 Terex Corporation.

Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USATel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com

www.terexmps.com

Form 25732 (5/13)

SPECIFICATIONS

Patent pending fines reject chute systemElectrical switchgear with variable frequency feeder driveSwitchgear panel push button controls or tethered control panelExtra off plant motor starters and controlsHeavy-duty bi-directional hydraulic tipping grid with 6" (152 mm)

nominal openingsEnclosed 3-phase electric/hydraulic unit for hydraulic tipping

grid operationTipping grid support legs and spillage wingsRadio remote for tipping grid and belt feeder speed control

30 hp (22 kW) overhead conveyor motor in place of 25 hp (19 kW) 100' (30.5 m) power cables with cable wraps for stowagePower cable quick disconnects12V or 24V plant hydraulic unitHeavy-duty hydraulic run-on jacksBelt scale on feed conveyorTwo-piece foldable side bulkheadsPortable screen lube filter unitDust suppression systemOversize 315 80R x 22.5 tires

*LJ-TSV6203 variable slope triple shaft high g-force 3-deck screen*Hydraulic raising module lifts screen up to 10° in 2.5° increments*Screen suspension and low-maintenance screen

stabilization system*Screen accepts 4' and 5' (1219 and 1524 mm) panels*Bottom deck deflector plates boost screen efficiencyLarge 16' x 8' (4877 x 2438 mm) feed hopper with rubber side curtains25 hp (19 kW), 42" (1067 mm) wide overhead conveyor with

dual hinge transition 15 hp (11 kW), 36" (914 mm) wide 3-ply belt, cartridge style belt feeder10 hp (7.5 kW), 48" (1220 mm) wide underscreen fines

conveyor, raises with screen in 2.5° incrementsTwo 7.5 hp (5.5 kW), 30" (762 mm) wide, reversible top and

center deck cross conveyors7.5 hp, 24" (610 mm) wide, reversible bottom deck cross conveyor

*Patent Pending

OptiOnal EquipmEnt

Standard FEaturES

terex® minerals processing SystemsCedarapids CrS6203FV

CrS6203FV pOrtaBlE FEEdEr/SCrEEn plant

Form 25734 (5/12)

Cross conveyors discharge 44" (1117 mm) beyond frame All conveyor belts are 3-ply with vulcanized belt splices 4-section, 2-position blending system to mix second and

bottom deck oversUnder-frame mounted triple axle spring suspension with

spring-applied brakes Six hydraulic leveling jacks and two pinned telescopic support legsEnclosed gas powered plant hydraulic unit for setting screen

slope, conveyor position, and jacksMany easy maintenance features including conveniently located

grease banks, cartridge style cross belt flashing and low-maintenance motion dampersMartin style conveyor belt wipersSide mounted lockable storage boxService platforms and guard rails around three sides of screen

with telescoping access ladder

CRS6203FV plant shown with the LJ-TSV variable slope screen in the 10° operating position

http://www.terex.com/minerals-processing-systems/en/products/new-equipment/portable-plants/screen-plants/CedarapidsCRS6203FV/index.htm

Effective Date: May 2012. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings inthis document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. © 2012 Terex Corporation.

Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USATel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com

Transport

Operational

LJ-TSV6203 screen ................................................. 6' x 20' (1829 x 6096 mm)Feed hopper ...............................................................8' x 16' (2438 x 4877 mm) Hopper capacity (below grid) ................................................... 15 yd3 (11.5 m3) Belt feeder ........................................................................................36" (914 mm)Overhead conveyor .......................................................................42" (1067 mm)Underscreen fines conveyor ........................................................48" (1220 mm)Reversible cross conveyor ............................................................. 24" (610 mm)Reversible cross conveyors (2) ....................................................30" (762 mm)Tires .................................................................................... Twelve 295 75R x 22.5

Horsepower LJ-TSV6203 screen ....................................................................40 hp (30 kW) Belt feeder ....................................................................................15 hp (11 kW) Overhead conveyor ..................................................................... 25 hp (19 kW) Underscreen fines conveyor .....................................................10 hp (7.4 kW) Reversible cross conveyors (3) ..............................................7.5 hp (5.6 kW) Grid electric/hydraulic unit.......................................................10 hp (7.4 kW)Estimated weight (fully optioned) Rear axle ......................................................................59,500 lbs (26,990 kg) Kingpin ......................................................................... 46,000 lbs (20,865 kg) Total .............................................................................105,500 lbs (47,855 kg)

terex® minerals processing SystemsCedarapids CrS6203FV portable Feeder/Screen plant

SpECiFiCatiOnS

www.terexmps.com

SpECiFiCatiOnS

14'1"(4293)

4'(1219)

4'(1219)

11" (279) 58'10" (17,932)77'8" (23,673)

3˚ Break Over Angle

4'10"(1473)

4'10"(1473)

5'3"(1600)

6'6" (1981)Axle Track

14'1"(4293)

11'11" (3632)

14'1"(4293)

4'(1219)

4'(1219)

11" (279) 58'10" (17,932)77'8" (23,673)

3˚ Break Over Angle

4'10"(1473)

4'10"(1473)

5'3"(1600)

6'6" (1981)Axle Track

14'1"(4293)

11'11" (3632)

Form 25734 (5/12)

4'9"(1448)

3'3"(991)

77'5" (23,597)16'8" (5080)14'6" (4420) 15'6" (4724) 5'4" (1626) 8' (2438) 19"

(483)7'9" (2362)

*16'10"(5131)

4'9"(1448)

3'3"(991)

77'8" (23,673)16'8" (5080)14'9" (4496)

*6'7"(2007)

15'6" (4724) 8' (2438) 19"(483)

7'9" (2362) 5'9" (1753)Rear Jacks8'10" (2692)

Front/Mid Jacks

*10'9"(3277)

*7'1"(2159)

5'11" (1803)Minimum

7'11" (2413) Max

*21'1"(6426)

10˚ Maximum2.5 ̊Increments

*12'4"(3759)

5'11" (1803)Minimum

7'11" (2413) Max

5'4" (1626)

Minimum 4" (102) CribbingRequired This Jack Leg Only

13" (330) Maximum Jack Lift

*14'8" (4470)Feed Height

*Operational heights shown include the maximum jack lift of 13" (330)