Crosby® Styles JOS-E, JBS-E, JLT-JOS-E, JLT-JBS-EPressure Relief Valves for air, gas, steam, vapor, liquid, and two-phase
applications in an exceptionally rugged, standardized design.
Crosby® Styles JOS-E, JBS-E, JLT-JOS-E, JLT-JBS-EPressure Relief Valves for air, gas, steam, vapor, liquid, and two-phase
applications in an exceptionally rugged, standardized design.
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 1
Styles JOS-E, JBS-E, JLT-JOS-E, JLT-JBS-EPressure Relief Valve Catalog
Revised March 2001Catalog: 310E-US.01
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5
JOS-E/JLT-JOS-E Materials of Construction . . . . . . . 6 - 7
JBS-E/JLT-JBS-E Materials of Construction . . . . . . . . 8 - 9
NACE MR0175 Sour Gas Service . . . . . . . . . . . . . . . 10 - 11
Caps and Lifting Levers . . . . . . . . . . . . . . . . . . . . . . . 12
Style Designation Chart . . . . . . . . . . . . . . . . . . . . . . . 13
O-Ring Seat Construction . . . . . . . . . . . . . . . . . . . . . 14
BlockBody Relief Valves . . . . . . . . . . . . . . . . . . . . . . 15
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . 15
Crosby Products and Services . . . . . . . . . . . . . . . . . . 16
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . 16
0 0 1
U K A SQUALITY
MANAGEMENTQ S 9 0 0 0
LLO
YD
'SR
EGIS
TER QUALITY
ASSU
RA
NC
E
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 2
Introduction
Crosby® Styles JOS-E and JBS-E spring-loaded pressure reliefvalves have been engineered to provide high quality over-pressure protection for air, gas, steam, vapor, liquid and two-phase applications in an exceptionally rugged, standardizeddesign to the process and power industries.
Standard sizes are 1 D 2 to 8 T2 10 with inlet flange ratings ofANSI Cl 150, 300, 600, 900, 1500 and 2500. Standard outletflanges are ANSI Cl 150 or Cl 300 depending on valve size orrating. Inlet and outlet center-to-face dimensions conform to APIStandard 526, Flanged Steel Pressure Relief Valves.
Styles JOS-E and JBS-E pressure relief valves aremanufactured in accordance with ASME Pressure Vessel Code,Section VIII and capacities are certified by the National Boardof Boiler and Pressure Vessel Inspectors.
All Crosby pressure relief valve castings and forgings areprocured to ASME/ASTM material specifications and are avail-able in a number of material combinations such as Monel®,Hastelloy® and stainless steel. In addition, Styles JOS-E andJBS-E relief valves offer a number of special materialcombinations such as Titanium, Duplex Stainless Steel andInconel®, and are available on application.
Dimensions of flanges conform to current ANSI Standards. Allsteel raised face flanges are spiral concentric serrated finishwith 45 to 55 grooves per inch and a finish between 125 Raand 200 Ra. Other flange facings, such as Ring Type Joint, areavailable on request.
For information pertaining to sizing and selection, refer to theAGC SafetySize computer sizing program and Pressure ReliefValve Engineering Handbook (Technical Document No. TP-V300).
Notes
1. Monel® and Inconel® are registered trademarks of theInternational Nickel Company, Inc.
2. Hastelloy® is a registered trademark of HaynesInternational, Inc.
Sizes: 1” D 2” to 8” T2 10”
Orifices: 0.110 to 27.872 in2 [71 to 17981 mm2]
Inlet Ratings: ANSI Cl 150, 300, 600, 900, 1500, 2500
Temperature Range: -450°F to +1000°F [-268°C to +538°C]
Pressure Range:JOS-E and JLT-JOS-E: 15 to 6000 psig [1.03 to 413.79 barg]JBS-E and JLT-JBS-E: 25 to 6000 psig [1.72 to 413.79 barg]
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 3
Extended Service Life, Reduced Cost of OwnershipSuperior Application Versatility
Improved, Rugged Nozzle Ring Design.
Improved Disc Insert Retention for Ease of Maintenance.
Standard Inconel 625 Bellows and Flange Material forSuperior Corrosion Resistance, Longer Service Life and aWider Range of Applications.
Universal Disc Holder Allows for Simple and Cost-EffectiveConversions from Conventional to Balanced Bellows Design.
Standard Threaded Bellows Design for Ease of Maintenanceand Conversion From Conventional to Balanced BellowsDesign.
Improved Corrosion Resistance with Standard 316 StainlessSteel Adjusting Bolt Locknut and Nozzle Ring Set Screwmaterials.
Style JLT Capacities Certified on Liquids and Gas.
Improved Parts Interchangeability - Regardless of TopConstruction.
Field Proven Style JLT Trim* for Stable, Non-ChatteringOperation on Liquid and Gas Service.* Patented
Standard Chrome Steel Spring for -75°F to +650°F [-28°C to +343°C].
Easily Converted to Any Type Cap or Lifting LeverConstruction, Liquid Trim, Soft-Seat or Balanced BellowsConfigurations.
Full Compliance with ASME Boiler and Pressure Vessel CodeSection VIII and API Standards 526 and 527.
Valve StylesJOS-E JLT-JOS-E
JBS-E JLT-JBS-E
JBS-BP-E JLT-JBS-BP-E
JOS-H-E
These Design Improvements and Material Upgrades, Combined with State-Of-The-Art Manufacturing Facilities, Result in Lower Cost of Ownership to End Users and Enhanced Product Availability from Crosby Factories
as well as Crosby’s Extensive Network of Pressure Management CentersSM .
Style JOS-E
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 4
Bellows and Top FlangeCrosby Styles JBS-E and JLT-JBS-E balanced bellows pressurerelief valves provide optimum valve performance when thedeveloped back pressure in exhaust systems or dischargemanifolds becomes excessive.
All standard JBS-E and JLT-JBS-E relief valves feature a standard bellows and top flange (Figure 1) manufactured fromInconel alloy 625 which is a fatigue-resistant material and provides improved corrosion resistance compared to 316Lstainless steel bellows. Inconel® alloy 625 is highly resistant to pitting, crevice corrosion and intergranular attack. The standardization of Inconel® Alloy 625 bellows and top flangeprovides a higher degree of corrosion resistance without thepremium extra charge usually associated with Inconel® bellows.
Ease of Maintenance andComponent InterchangeabilityThe disc insert retention, disc holder and nozzle ring of the JOS-Eand JBS-E have been re-engineered to improve maintenance,minimize spare parts and provide more component partinterchangeability. (Figure 2)
The disc insert is inserted into the disc holder with a retention clipwhich is compressed as it passes through the smallest diameter inthe disc holder recess and then returns to its normal shape once ithas passed through. With the retention clip in its original shape,the disc insert is held securely in place.
A “universal” disc holder allows for simple and cost effectiveconversions from conventional to balanced bellows design as wellas cost-effective bellows replacement. The bellows threads on tothe disc holder with a tailpiece and gasket.
The new nozzle ring encloses the adjustment slot at the bottom ofthe ring giving a more rugged, durable design.
Chrome Steel SpringStandard chrome steel spring material for applications with inlettemperatures up to 650°F [343°C].
Styles JOS-E and JBS-EProduct Features -
Figure 1
Figure 2
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 5
Dual CertificationCrosby patented Style JLT (Figure 3) pressure relief valves offera significant increase in capacity at 10% overpressure resultingin the economic use of a smaller valve as well as a reduction in inlet and discharge piping costs. The JLTtrim is a field-proven patented design providing stable, non-chattering operation for liquid service.
The JLT design is also capacity certified on gas and vaporservice and can be applied in two-phase flow applications. TheJLT design is a logical choice for applications where the processfluid may be a liquid or a gas depending on the overpressurecondition.
Bellows ConvertibilityThe Crosby flanged, spring operated pressure relief valve isdesigned and manufactured as a conventional valve and abalanced bellows valve. The conversion from conventionalStyles JOS-E or JLT-JOS-E in 1 D 2 through 8 T2 10 requiresonly the addition of a bellows assembly and bellows tail-piecegasket. No other parts are necessary since all other parts arecompletely interchangeable.
Seat DesignStyles JOS-E and JBS-E relief valves are available with flatmetal-to-metal seats or soft seats. The JOS-E and JBS-E two-piece disc holder/disc insert construction provides thermalbalancing assuring maximum seat tightness, and meets therequirements of API Standard 527, Seat Tightness of PressureRelief Valves.
Where system operating conditions permit, soft seat orelastomer seat construction is available as an option. TheCrosby O-ring soft seat (Figure 4) is a two-seat design, with ametal-to-metal seat located downstream of the soft seat. The O-ring is the primary seal. The secondary flat metal-to-metalseat controls the compression of the O-ring and also serves as asecondary seal should the O-ring be damaged. Elastomeric O-ring soft seat valves are seat tightness tested at 95% of setpressure, exceeding the requirements of API Standard 527.
Standard O-ring materials include Viton®1, BUNA-N, EPR2,TFE3, Silicone Rubber and Kalrez4. Pressure and temperaturelimits of each material are shown on page 16. Other soft seatmaterials such as Chemraz5 and Aflas6 are available onapplication.
Cap, Lifting Lever and Spindle InterchangeabilityAll Crosby JOS-E and JBS-E relief valves use a threadedspindle and drilled and tapped bonnet which permits easy cap orlifting lever conversions, with maximum standardization andinterchangeability of parts. In addition, standard cap and liftinglever designs can be used with in-line test devices.
Styles JOS-E and JBS-EProduct Features -
Figure 3
Figure 4
Notes
1. Reg. U.S. Patent Office for DuPont’s fluoroelastomer.
2. EPR = Ethylene Propylene Rubber.
3. TFE = Tetrafluoroethylene.
4. Reg. U.S. Patent Office for DuPont’s perfluoroelastomer parts.
5. Registered Trademark of Greene, Tweed & Co.
6. Registered Trademark of Asahi Glass Company, Ltd.
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 6
Crosby Styles JOS-E and JLT-JOS-E are the standardconventional relief valve designs for applications when thedischarge is to the atmosphere or when the discharge is to alow pressure exhaust system designed to contain the processfluid. Valves subject to flashing fluids may require a balancedbellows type valve (see page 8).
This exceptionally rugged design features a high guidingsurface ratio, corrosion resistant trim, upgraded materials ofconstruction and several other design improvements to ensure
ease of maintenance as well as a greater degree of partsinterchangeability.
For liquid service applications, Style JLT-JOS-E relief valvesprovide stable operating performance using the widely industryrecognized liquid trim design patented by Crosby. The discholder in the liquid trim design has been engineered to allow thevalve to achieve full lift at 10% overpressure without valvechatter.
Styles JOS-E and JLT-JOS-E Standard Materials of Construction
Ref. No. Part Name Standard Material
1 Body (JOS-E and JLT-JOS-E ( )5 and ( )6) ASME SA216 GR. WCB
1 Body (JOS-E and JLT-JOS-E ( )7) ASME SA217 GR. WC6
2 Nozzle 316 Stainless Steel
3 Nozzle Ring 316 Stainless Steel
4 Set Screw 316 Stainless Steel
5 Disc Holder 316L Stainless Steel
8 Disc Insert1 316 Stainless Steel
9 Retention Clip2 Inconel® X750
12 Retainer Screws 316 Stainless Steel
11 O-ring Retainer 316 Stainless Steel
10 O-ring1 Specify
15 Guide ASTM A297 GR. HE SST
16 Spindle 416 Stainless Steel
17 Spindle Cotter Pin Stainless Steel
18 Spring (JOS-E and JLT-JOS-E ( )5) Chrome Steel3
18 Spring (JOS-E and JLT-JOS-E ( )6 and ( ) 7) Alloy Steel 3,4
19 Spring Washers Carbon Steel
20 Bonnet (JOS-E and JLT-JOS-E ( )5 and ( )6) ASME SA216 GR. WCB
20 Bonnet (JOS-E and JLT-JOS-E ( )7) ASME SA217 GR. WC6
21 Bonnet Stud ASME SA193 GR. B7
22 Bonnet Stud Nut ASME SA194 CL 2H
24 Adjusting Bolt 316 Stainless Steel
25 Adjusting Bolt Nut 316 Stainless Steel5
26 Pipe Plug (Bonnet) Carbon Steel
27 Set Screw Gasket1 Organic Fiber Non-Asbestos
28 Guide Gasket1 Organic Fiber Non-Asbestos
34 Seal and Wire Lead and Stainless Steel
35 Seal Clip (Not Shown) Stainless Steel
36 Nameplate (Not Shown) Stainless Steel
40 Threaded Cap Carbon Steel
41 Cap Gasket1 Organic Fiber Non-Asbestos
Notes
1. Recommended Spare Part.
2. Furnished with Disc Insert.
3. Corrosion resistant coating.
4. Crosby may upgrade to Inconel® X750.
5. Class 900#, 1500# nd 2500# inlet ratingsuse 416 Stainless Steel.
Styles JOS-E and JLT-JOS-E Conventional Pressure Relief Valves
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 7
40
24
25
34
19
20
18
19
21
22
15
5
34
3
4
8
27
1
2
41
26
16
17
28
29
12
11
10
Style JOS-E(with metal-to-metal seat)
Style JLT-JOS-E(with O-ring seat)
Styles JOS-E and JLT-JOS-E Conventional Pressure Relief Valves
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 8
Styles JBS-E and JLT-JBS-E Balanced Bellows Construction
Crosby Styles JBS-E and JLT-JBS-E are pressure relief valvesincorporating a bellows which is balanced to minimize the effectof back pressure on the performance characteristics. Thebalanced bellows design offsets the effects of variable backpressure on valve set pressure. The balanced bellows valve canalso handle applications involving high built-up back pressure.
Additionally, the bellows serves to isolate the guide, spindle,spring and other parts contained in the bonnet chamber fromcorrosive fluids or media such as a highly viscous fluid or slurrywhich could render the relief valve inoperative.
For liquid service applications, Crosby offers Style JLT-JBS-Erelief valves.
The standard bellows assembly of the Crosby Style JBS-E andJLT-JBS-E threads onto the disc holder with a bellows tailpieceand gasket. A welded bellows attachment is available as anoption.
The JBS-E and JLT-JBS-E bellows and bellows flange aresupplied in Inconel 625 as standard material for improveddurability, corrosion resistance and service life.
Styles JBS-E and JLT-JBS-E Standard Materials of Construction
Ref. No. Part Name Standard Material
1 Body (JBS-E and JLT-JBS-E ( )5 and ( )6) ASME SA216 GR. WCB
1 Body (JBS-E and JLT-JBS-E ( )7) ASME SA217 GR. WC6
2 Nozzle 316 Stainless Steel
3 Nozzle Ring 316 Stainless Steel
4 Set Screw 316 Stainless Steel
5 Disc Holder 316L Stainless Steel
6C Bellows Flange1 Inconel® 625
6B Bellows1 Inconel® 625
6A Bellows Tailpiece1 316L Stainless Steel
29 Tailpiece Gasket2 Organic Fiber Non-Asbestos
8 Disc Insert2 316 Stainless Steel
9 Retention Clip3 Inconel® X750
12 Retainer Screws 316 Stainless Steel
11 O-ring Retainer 316 Stainless Steel
10 O-ring2 Specify
15 Guide ASTM A297 GR. HE SST
16 Spindle 416 Stainless Steel
17 Spindle Cotter Pin Stainless Steel
18 Spring (JBS-E and JLT-JBS-E ( )5) Chrome Steel4
18 Spring (JBS-E and JLT-JBS-E ( )6 and ( )7) Alloy Steel4,5
19 Spring Washers Carbon Steel
20 Bonnet (JBS-E and JLT-JBS-E ( )5 and ( )6) ASME SA216 GR. WCB
20 Bonnet (JBS-E and JLT-JBS-E ( )7) ASME SA217 GR. WC6
21 Bonnet Stud ASME SA193 GR. B7
22 Bonnet Stud Nut ASME SA194 CL 2H
24 Adjusting Bolt 316 Stainless Steel6
25 Adjusting Bolt Nut 316 Stainless Steel
27 Set Screw Gasket1 Organic Fiber Non-Asbestos
28 Guide Gasket2 Organic Fiber Non-Asbestos
34 Seal and Wire Lead and Stainless Steel
35 Seal Clip (not shown) Stainless Steel
26 Nameplate (not shown) Stainless Steel
40 Threaded Cap Carbon Steel
41 Cap Gasket2 Organic Fiber Non-Asbestos
Notes
1. Subassembly.
2. Recommended Spare Part.
3. Furnished with Disc Insert.
4. Corrosion resistant coating.
5. Crosby may upgrade to Inconel® X750.
6. Class 900#, 1500# nd 2500# inlet ratingsuse 416 Stainless Steel.
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 9
Styles JBS-E and JLT-JBS-E Balanced Bellows Construction
40
24
25
34
19
20
18
19
21
22
15
5
34
3
4
8
27
1
2
41
Note: This vent must remainopen on JBS-E andJLT-JBS-E construction
16
17
28
29
9
6C6B6A
Style JBS-E(with metal-to-metal seat)
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 10
Level 1 - For applications where compliance with NACEMR0175 is required for wetted parts in the primary(upstream) pressure zone of the pressure relief valve.Materials of construction for Level 1 can be found onpage 8.
Level 2 - For applications where compliance with NACEMR0175 is required for wetted parts in the primary(upstream) and secondary (downstream) pressurezones of the pressure relief valve. The Inconel® 625bellows isolates the valve spring and other criticalcomponents above it from the process fluid.
While the materials recommended for the CrosbyStyle JBS-E and JLT-JBS-E sour gas valves aresuitable for average service conditions, optionalmaterials are available to provide additionalresistance to corrosion beyond the minimumrequirements of the standard.
Ref No. Part Name Standard NACE Material Level 2
1 Body ASME SA216 GR. WCB
2 Nozzle 316 Stainless Steel
3 Nozzle Ring 316 Stainless Steel
4 Set Screw 316 Stainless Steel
6C Bellows Flange1 Inconel® 625
6B Bellows1 Inconel® 625
6A Bellows Tailpiece1 316L Stainless Steel
29 Tailpiece Gasket Organic Fiber Non-Asbestos
5 Disc Holder 316L Stainless Steel
8 Disc Insert 316 Stainless Steel
9 Retention Clip Inconel® X750
15 Guide ASTM A297 GR. HE SST
16 Spindle 416 Stainless Steel
17 Spindle Cotter Pin Stainless Steel
18 Spring Chrome Steel-Aluminum Metallized
19 Spring Washer Steel
20 Bonnet ASME SA216 GR. WCB
21 Bonnet Stud Alloy Steel2
22 Bonnet Stud Nut Steel2
24 Adjusting Bolt 316 Stainless Steel3
25 Adjusting Bolt Nut 316 Stainless Steel
27 Set Screw Gasket Organic Fiber Non-Asbestos
28 Guide Gasket Organic Fiber Non-Asbestos
34 Seal and Wire Lead and Stainless Steel
35 Seal Clip (not shown) Stainless Steel
40 Threaded Cap Carbon Steel
41 Cap Gasket Organic Fiber Non-Asbestos
Shaded materials indicate variation from standard product.
Notes
1. Subassembly.
2. If Class I or II bolting is required, bonnet studs will beASME A193 Gr B7M HRC-22 maximum and bonnet studnuts will be ASME A194 Class 2HM HRC-22 maximum.
3. Class 900#, 1500# nd 2500# inlet ratings use 416Stainless Steel.
Styles JBS-E and JLT-JBS-E Balanced Bellows Pressure Relief Valves for Sour Gas Service per NACE MR0175
Style JBS-E(with bellows)
40
2425
34
19
20
1819
21
2215
5
34
34
8
2712
41
16
17
28
29
9
6C6B6A
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 11
Level 1 - For applications where compliance with NACEMR0175 is required for wetted parts in the primary(upstream) pressure zone of the pressure relief valve.Materials of construction for Level 1 can be found onpage 6.
Level 2 - For applications where compliance with NACEMR0175 is required for wetted parts in the primary(upstream) and secondary (downstream) pressurezones of the pressure relief valve.
While the materials recommended for the CrosbyStyle JOS-E and JLT-JOS-E sour gas valves aresuitable for average service conditions, optionalmaterials are available to provide additionalresistance to corrosion beyond the minimumrequirements of the standard.
Ref No. Part Name Standard NACE Material Level 2
1 Body ASME SA216 GR WCB
2 Nozzle 316 Stainless Steel
3 Nozzle Ring 316 Stainless Steel
4 Set Screw 316 Stainless Steel
5 Disc Holder 316L Stainless Steel
8 Disc Insert 316 Stainless Steel
9 Retention Clip Inconel® X750
15 Guide ASTM A297 GR. HE SST
16 Spindle 316 Stainless Steel
17 Spindle Cotter Pin Stainless Steel
18 Spring Inconel® X750
19 Spring Washer 316 Stainless Steel
20 Bonnet ASME SA216 GR WCB
21 Bonnet Stud Alloy Steel1
22 Bonnet Stud Nut Alloy Steel1
24 Adjusting Bolt 316 Stainless Steel
25 Adjusting Bolt Nut 316 Stainless Steel
26 Pipe Plug (Bonnet) Carbon Steel
27 Set Screw Gasket Organic Fiber Non-Asbestos
28 Guide Gasket Organic Fiber Non-Asbestos
34 Seal and Wire Lead and Stainless Steel
35 Seal Clip (not shown) Stainless Steel
40 Threaded Cap Carbon Steel
41 Cap Gasket Organic Fiber Non-Asbestos
Shaded materials indicate variation from standard product.
Styles JOS-E and JLT-JOS-E Conventional Pressure Relief Valves for Sour Gas Service per NACE MR0175
Note
1. If Class I or II bolting is required, bonnet studs will beASME A193 Gr B7M HRC-22 maximum and bonnetstud nuts will be ASME A194 Class 2HM HRC-22 maximum.
Style JOS-E
40
2425
34
19
20
1819
21
2215
5
34
3
4
8
2712
41
26
16
17
28
29
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 12
Caps and Lifting Levers
Cap
Sealand
Wire
Cap
Spindle
Cap GasketThreaded Cap
Type A Type J(standard)
Test Rod
Cap orCap Top
Spindle
Cap Plug
CapPlug
Gasket
Cap Test RodType B - Threaded CapType E - Packed Lifting LeverType H - Bolted CapType K - Threaded Cap (standard)Type M - Bolted Cap (standard)
Lever NutLever NutLockwasher
Lever
PackingGland
Dog ShaftGasket
Dog Shaft
Packing Gland Sleeve
Packing Gland Nut
Packing
Packed Lifting LeverType D
(Top view of Packing Gland constructionused for special materials)
Lever
Dog Shaft
Cap
O-ring
Dog
ValveSpindle
Lever Nut
Lockwasher
Dog Shaft Bearing
Gasket
Packed Lifting LeverType D
(Top view)
Cotter Pin
Cap TopGasket
Dog
DogShaft
Spindle
AdjustingBolt
AdjustingBolt Nut
Seal andWire
Cap Stud Nut
Cap Stud
Cap
Spindle Nut
Cap Top
Packed Lifting LeverType D
Cap Gasket
CapSpindle Nut
Regular Lifting LeverType C
Cotter Pin
Pin
Forked Lever
Cotter Pin
Pin Cap SetScrew
Lever
Cap
Cap
Bolted CapType G Type L
(standard)
Cap Stud
Spindle
Cap StudNut
SealandWire
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 13
Pressure/TemperatureInlet Flange Range Ratings3
Style Designations
Notes
1. Style designations “JLT-JOS-E”, “JLT-JBS-E”, or “JLT-JBS-BP-E” signify StylesJOS-E, JBS-E or JBS-BP-E with liquid trim for liquid service.
2. Upper temperature limit is +800°F [+427°C] for Style JOS-H-E open bonnet valvefor ASME Code Section VIII steam service.
3. See pages 14 - 43 in Catalog 310 for appropriate maximum set pressures andtemperatures.
4. See pages 12 - 13 in Catalog 310 for complete listings of materials of construc-tion.
5. Larger sizes are available. Ask for Catalog No. 307.
6. ASME Code Section VIII rules require that pressure relief valves for water serviceover +140°F [+60°C], steam and air shall have a lifting device.
* Reg. U.S. Patent Office for DuPont’s fluorocarbon resins.
Available Options
Welded bellows attachment
Flange facings such as ring type joint
Sour gas service materials and certifications
Special Cl 300 outlets (where not standard)
Special Teflon®* (FEP) bellows coating
Special spring coatings or plating
Block bodies
Bonnet and cap inside painting or plastic coating
Bug screens
Special materials not cataloged
Flanges to international standards
Special flanges
Stellited nozzle and disc insert
Special casting or machined surface tests
Special cleaning
Special painting or coatings
Special testing
Steam jacketed bodies
Supplementary loading
Seat TypeStyleSize
Inlet x Orificex Outlet
Material Variations4
Caps and LiftingLevers (Type)
1” D 2”thru8” T2 10”5
JOS-E-Conventional
JBS-E-with bellows
JLT-JOS-E-Conventional withliquid trim1
JLT-JBS-E-Bellowswith liquid trim1
JBS-BP-E-Bellowswith back pressurebalancing piston
JLT-JBS-BP-E-Bellows with liquidtrim and backpressure balancingpiston1
JOS-H-E -Conventional JOSwith open bonnetfor ASME CodeSection VIII steamservice to +800°F[+427°C]2
1 - Cl 150 Flange
2 - Cl 300 Flange
3 - Cl 300 Flange
4*- Cl 600 Flange
5 - Cl 900 Flange
6 - Cl 1500 Flange
7 - Cl 2500 Flange
*Except “T” and “T2”orifice is Cl 300flange *Except for Style
JOS-H-E with openbonnet, chrome steelspring may be used to+800°F [+427C°]
When orderingsoft seats, speci-fy material.
2 - -450°F to -76°F[-268°C to -60°C]
4 - -75°F to -21°F[-59°C to -30°C]
5*- -20°F to +650F[-29°C to +343°C]
6 - +651°F to +800°F[+344°C to +427°C]
7 - +801°F to +1000°F[+428°C to +538°C]
None - Metal
“OR” - O-Ring
None - StandardMaterials
S - All 316 St. St.
S4 - All 316 St. St.except body,bonnet, cap andspring
M - All Monel® withMonel® orInconel spring
M1 - Monel® nozzleand disc insert
M4 - All Monel®except body,bonnet, cap,spring andwashers
M5 - All Monel®except springand washers
H - All Hastelloy® C
H1 - Hastelloy® Cnozzle and discinsert
H4 - All Hastelloy® Cexcept body,bonnet, cap,spring andwashers
H5 - All Hastelloy® Cexcept springand washers
N2 - NACE Level 2JOS-E = Inconel® X750spring, 316 St.St. washers,spindle andadjusting boltJBS-E = AluminumMetallizedSpring
Type J - (Standard)threaded cap
Type K - Threaded capwith test rod
Type C - Regular liftinglever6
Type D - Packed liftinglever6
Type E - Packed liftinglever with testrod6
Type L - Bolted cap
Type M -Bolted capwith test rod
Optional Caps forHeight Restricted
Applications
Type A - Threaded cap
Type B - Threaded capwith test rod
Type G - Bolted cap
Type H - Bolted capwith test rod
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 14
EPR = Ethylene Propylene Rubber TFE = Tetrafluoroethylene
Note: Other soft seat materials are available on request. For O-ring seats below -150°F [-101°C] consultCrosby. For steam service, metal-to-metal seats are recommended; consult Crosby if soft seats are required.
O-Ring Soft Seat Materials and Pressure/Temperature Limits
Maximum Set Pressure Limits
Maximum Set PressureOrifice psig barg
D 1480 102
E 1480 102
F 1480 102
G 1480 102
H 1480 102
J 1480 102
K 1480 102
L 1000 68.9
M 1100 75.8
N 1000 68.9
P 1000 68.9
Q 600 41.3
R 300 20.6
T 300 20.6
T2 300 20.6
JBS-E O-RingSoft Seat
JLT-JOS-E O-RingSoft Seat
500
400
300
200
100
50
0
-150
-50
Set Pressure, psigFigures in ( ) are Durometer Hardness Specifications.
-101
-45
-17
93
204
260
15 100 200 300 400 500 600 700 800 900 1000 1200 1400
Inle
t Te
mp
erau
ture
, °F
1480 or max. set pressurerating of the O-ring soft seat valve.
Inle
t Te
mp
erau
ture
, °C
Kalrez® (90)TFE
TFE
Kalrez® (80)Silicone (80)Viton® (75)TFE
Kalrez® (90)Viton® (90)TFE
BUNA-N (70)EPR (80)Kalrez® (80)Silicone (70)Viton® (75)TFE
BUNA-N (60)EPR (70)Silicone (50)
BUNA-N (90)EPR (90)Kalrez® (90)Viton® (90)TFE
BUNA-N (70)EPR (70)
Silicone (70)TFE
TFE TFE
BUNA-N (90)EPR (90)
Silicone (80)TFE
BUNA
-N (5
0)EP
R (7
0)Si
licon
e (5
0)Vi
ton®
(75)
Kalre
z® (8
0)Si
licon
e (5
0)Vi
ton®
(75)
Kalre
z® (8
0)
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 15
Crosby BlockBodyTM Pressure Relief Valves provide the solution toapplications involving very high set pressures that exceed standard ranges.
One single Crosby BlockBodyTM Pressure Relief Valve installation canhandle the capacity of multiple API-526 standard valves with:• Fewer potential leak paths.• Fewer spare parts required.• Cost savings on inlet and outlet piping.
Design Details:• Full nozzle design for maximum tightness.• Geometrically designed valve block body and bonnet for weight savings.• Interference fitted inlet studs provided.• Available in orifice sizes from “D” through “T2”.• Materials of construction available for special process applications.• Available in Crosby Styles JOS-E, JBS-E and JLT-E valve designs.
For more information, contact the Factory or your local CrosbyRepresentative.
Ordering Information
The primary purpose of Style JOS/JBS/JLT-E pressure reliefvalves is to protect lives and property. In order to select theproper valve for your application, please provide the informationlisted below. Details of the process fluid and conditions areespecially important. If there is any doubt as to selection orapplication of valves or parts, please contact your local CrosbySales Office or Representative.
Ordering Information Example
Quantity 5
Nominal valve size (inlet x orifice x outlet) 4 x L x 6
Valve style JOS-E-45
Inlet connection rating and facing 600 RF
Outlet connection rating and facing 150 RF
Service (liquid, gas or vapor) Air
Set pressure (psig) 800 psig
Back pressure (psig) if any, and Atmospherewhether constant or variable
Maximum service temperature (°F) Ambient 60°F
Cap or lifting lever type Type C
Valve materials Standard
Seat material Metal-to-metal standard
Code requirements ASME Unfired Pressure Vessel Code Section VIII
Required capacity 45433 SCFM
Accumulation (allowable overpressure) 10%
Molecular weight - vapor -
Specific gravity - gases and liquids 1.0
Viscosity - liquids -
PartsTo order parts, the following information should be included:
1. Quantity
2. Part name, i.e., disc insert
3. Size, style and valve number
4. Assembly number (from valve nameplate)
5. Serial number (from valve nameplate)
6. Original purchase order number (if assembly number has beendestroyed).
Sample Nameplate(Figures shown are for illustrative purposes only.)
Crosby provides special “fast response” delivery service of spareparts to satisfy unplanned parts requirements. Fast responsedelivery service can be initiated by contacting your local Crosbyrepresentative. Emergency delivery service is available directfrom the factory, 24 hours a day, 7 days a week by calling (508) 384-3121.
Springs with Washers To order springs with washers, inaddition to the other information included for "Parts," the requiredvalve set pressure must also be specified. If the spring is for anon-bellows valve, and there is a constant back pressurecondition, that too should be specified. Also specify springmaterial and coating if other than standard.
Replacement Valves To replace a valve in service, theassembly number, serial number, set pressure and previousorder number should be specified.
Crosby BlockBodyTM Pressure Relief Valves
Crosby® Styles JOS-E, JBS-E,JLT-JOS-E, JLT-JBS-E Pressure Relief Valve Catalog
© 2001, Crosby reserves the right to changeproduct designs and specifications without notice. 16
Crosby Products and Services
• Pressure Relief Valves for Air, Steam, Vapor and LiquidService - Spring Loaded and Pilot Operated
• Safety Valves for Fossil and Nuclear Power Plants
• Safety Selector Valve “Switchover” Device for ContinuousRelief Protection
• Pressure/Vacuum Relief Valves for Sanitary, Beverage, Foodand Pharmaceutical Industries
• Valves for Chlorine, Bromine, Fluorine and Other CorrosiveServices
• Valve Test Benches and Silencers
• Set Pressure Verification Device (SPVD) and Valve PositionIndication (VPI) Systems
• Comprehensive Test Facilities for Air, Steam and Water
• Severe Service BlockBodyTM for High Temperature and HIghPressure Applications
• Valve Service, Repair and Reconditioning, and Training
• Engineering Design, Application and Analytical Services
See your local Crosby Representative or Pressure Management CenterSM
Pressure Management Centers
Full Spectrum Services Crosby's Pressure ManagementCentersSM are designed to save you money. Whether or notyour organization performs its own repair and maintenance,Crosby Pressure Management Centers offer Crosby’s completeline of loosely assembled valves, spare parts, field service,valve management programs, and the repair and trainingexpertise required to keep your plants running longer and main-tenance investment at a minimum. Call Crosby Valve or yournearest Crosby Pressure Management Center.
WARNINGThe information contained in this catalog is for informational purposes only. The actual selection of valve products is dependent upon numerous factors and should be made onlyafter consultation with applicable Crosby personnel. Crosby assumes no responsibility for the actual selection of such products and hereby expressly disclaims liability for any andall claims and damages which may result from the use or application of this information or from any consultation with Crosby personnel.
WARRANTY
Anderson Greenwood Crosby, Crosby Valve and Engineering Division, Anderson Greenwood/Crosby Valve Division, or Crosby Valve Sales and ServiceCorporation (collectively “Crosby”) hereby warrants that the goods delivered under contract will be free from defect in material and workmanship for a periodof 18 months from shipment or 12 months from installation, whichever is earlier. Within this period, any of our products claimed defective may be returned toour factory after examination by us, the products will be repaired or replaced free of charge, F.O.B. our factory. Such defects shall be exclusive of the effectsof corrosion, erosion, normal wear or improper handling or storage.
Crosby makes no representation, warranty or guarantee, express or implied, with regard to our products except as specifically stated. When in doubt as tothe proper application of any particular product, you are invited to contact your nearest CROSBY office or representative. We cannot otherwise be responsi-ble for the selection of unsuitable equipment. Suitability of the material and product for the use contemplated by the buyer shall be the sole responsibility ofthe buyer.
Except as specifically set forth above and for warranty of title, CROSBY MAKES NO WARRANTY, EXPRESS OR IMPLIED, OF ANY KIND INCLUDINGWITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
In no event will CROSBY be liable for incidental or consequential damages.
WARNINGThe Product is a safety related component intended for use in critical applications. The improper application, installation or maintenance of the Product orthe use of parts or components not manufactured by Crosby may result in failure of the Product. The advice of a qualified engineer should be sought prior toany use of the Product.
Any installation, maintenance, adjustment, repair or test performed on the Product must be done in accordance with the requirements of all applicableCodes and Standards.
The information, specifications and technical data (the “Specifications”) contained in this document are subject to change without notice. Crosby does notwarrant that the Specifications are current and assumes no responsibility for the use or misuse thereof. The Purchaser should verify that there have been nochanges to the Specifications prior to use.
Crosby® Styles JOS-E, JBS-E, JLT-JOS-E, JLT-JBS-E Revised March 2001Catalog: 310E-US.01
Corporate Headquarters and Operations CenterP.O. Box 944Stafford, Texas 77497, USATelephone: (281) 274-4400, Fax: (281) 240-1800
Operations Centers43 Kendrick Street, Wrentham, Massachusetts 02093-0308, USATelephone: 1-508-384-3121, Fax: 1-508-384-8675
Crosby Road, Market Harborough, Leics LE16 9EE, UKTelephone: 44-1858-467281, Fax: 44-1858-434728
No. 45, Tuas Avenue 9, Jurong, Singapore 639 189Telephone: 65-862-2177, Fax: 65-862-1778
www.andersongreenwood.com
© 2001 Anderson Greenwood Crosby Printed in USA JOSE-10M-03/01
Flow Control
ANDERSONGREENWOODCROSBY