Date post: | 22-Dec-2015 |
Category: |
Documents |
View: | 218 times |
Download: | 0 times |
CS 61C L31 Verilog I (1) Garcia, Spring 2004 © UCB
Lecturer PSOE Dan Garcia
www.cs.berkeley.edu/~ddgarcia
inst.eecs.berkeley.edu/~cs61c CS61C : Machine Structures
Lecture 31 – Verilog II
2004-04-09
Fewer Princeton As! They had been giving
up to 46% of its students As; they has vowed to drop it to 35%. Berkeley EECS has 17% As for lower div & & 23% As
for upper div. “At Cal, an A is an A!”
cnn.com/2004/EDUCATION/04/08/princeton.grade.ap/www.eecs.berkeley.edu/Policies/ugrad.grading.shtml
CS 61C L31 Verilog I (2) Garcia, Spring 2004 © UCB
Review• Verilog allows both structural and behavioral
descriptions, helpful in testing
• Syntax a mixture of C (operators, for, while, if, print) and Ada (begin… end, case…endcase, module …endmodule)
• Some special features only in Hardware Description Languages
• # time delay, initial vs. always
• Verilog easier to deal with when thought of as a hardware modeling tool, not as a prog lang.
• Want to Monitor when ports, registers updated
• Verilog can describe everything from single gate to full computer system; you get to design a simple processor
CS 61C L31 Verilog I (3) Garcia, Spring 2004 © UCB
Corrections/Clarifications from last time• No semicolons after end next to endmodule, nor after endmodule(When in doubt, tutorial beats slides)
begin …end
endmodule
• Timing: Review time, variable update, module invocation, and monitor
CS 61C L31 Verilog I (4) Garcia, Spring 2004 © UCB
Review: Verilog Pedagogic Quandary• Using Verilog subset because full Verilog supports advanced concepts that are not described until >= CS 150, and would be confusing to mention now
• Trying to describe a new language without forcing you to buy a textbook, yet language bigger diff than C vs. Java
• Hence Wawrzynek Verilog tutorial• We’ll go through most of tutorial together
• Do the tutorials, don’t just Read them
CS 61C L31 Verilog I (5) Garcia, Spring 2004 © UCB
Time, variable update, module, & monitor
• The instant before the rising edge of the clock, all outputs and wires have their OLD values. This includes inputs to flip flops. Therefore, if you change the inputs to a flip flop at a particular rising edge, that change will not be reflected at the output until the NEXT rising edge. This is because when the rising edge occurs, the flip flop still sees the old value. So when simulated time changes in Verilog, then ports, registers updated
or #2(Z, X, Y);
Z
X
Y
CS 61C L31 Verilog I (6) Garcia, Spring 2004 © UCB
Example page 6 in Verilog Tutorial//Test bench for 2-input multiplexor.
// Tests all input combinations.module testmux2;reg [2:0] c;wire f;reg expected;mux2 myMux (.select(c[2]), .in0(c[0]), .in1(c[1]), .out(f));initial
beginc = 3'b000; expected=1'b0; ...•Verilog constants syntax N’Bxxx where
N is size of constant in bits B is base: b for binary, h for hex, o for octal xxx are the digits of the constant
CS 61C L31 Verilog I (7) Garcia, Spring 2004 © UCB
Example page 7 in Verilog Tutorial… begin
c = 3'b000; expected=1'b0;repeat(7)begin#10 c = c + 3'b001;if (c[2]) expected=c[1];
else expected=c[0];end
#10 $finish;end
•Verilog if statement, for and while loops like C•repeat (n) loops for n times (restricted for)• forever is an infinite loop
•Can select a bit of variable (c[0] )• $finish ends simulation
CS 61C L31 Verilog I (8) Garcia, Spring 2004 © UCB
Example page 7 in Verilog Tutorial...
endinitial
begin$display("Test of mux2.");$monitor("[select in1 in0]=%b out=%b expected=%b time=%d",c, f, expected,
$time);endendmodule // testmux2
•Verilog “printf” statements •$display to print text on command• $write to print text on command, no new line•$strobe prints only at certain times•$monitor prints when any variable updated
CS 61C L31 Verilog I (9) Garcia, Spring 2004 © UCB
Output for example on page 7 (no delay)Test of mux2.
[select in1 in0]=000 out=0 expected=0 time=0
[select in1 in0]=001 out=1 expected=1 time=10
[select in1 in0]=010 out=0 expected=0 time=20
[select in1 in0]=011 out=1 expected=1 time=30
[select in1 in0]=100 out=0 expected=0 time=40
[select in1 in0]=101 out=0 expected=0 time=50
[select in1 in0]=110 out=1 expected=1 time=60
[select in1 in0]=111 out=1 expected=1 time=70
•Note: c output is 3 bits (000 … 111) because c declared as 3 bit constant
CS 61C L31 Verilog I (10) Garcia, Spring 2004 © UCB
Example page 10 Verilog Tutorial // 4-input multiplexor built from // 3 2-input multiplexors
module mux4 (in0, in1, in2, in3, select, out);input in0,in1,in2,in3;input [1:0] select;output out;wire w0,w1;mux2
m0 (.select(select[0]), .in0(in0), .in1(in1), .out(w0)),m1 (.select(select[0]), .in0(in2), .in1(in3), .out(w1)),m2` (.select(select[1]), .in0(w0), .in1(w1), .out(out));
endmodule // mux4
What are m0, m1, m2?
What is size of ports?
CS 61C L31 Verilog I (11) Garcia, Spring 2004 © UCB
Part of example page 11 Verilog Tutorial ...
case (select) 2'b00: expected = a;2'b01: expected = b;2'b10: expected = c;2'b11: expected = d;
endcase; // case(select)...
•Verilog case statement different from C• Has optional default case when no match to other cases• Case very useful in instruction interpretation; case using opcode, each case an instruction
CS 61C L31 Verilog I (13) Garcia, Spring 2004 © UCB
Rising and Falling Edges and Verilog• Challenge of hardware is when do things change relative to clock?
• Rising clock edge? (“positive edge triggered”)
• Falling clock edge? (“negative edge triggered”)
• When reach a logical level? (“level sensitive”)
• Verilog must support any “clocking methodology”
• Includes events “posedge”, “negedge” to say when clock edge occur, and “wait” statements for level
CS 61C L31 Verilog I (14) Garcia, Spring 2004 © UCB
Example page 12 Verilog Tutorial// Behavioral model of 4-bit Register:// positive edge-triggered,// synchronous active-high reset.module reg4 (CLK,Q,D,RST);input [3:0] D;input CLK, RST;output [3:0] Q;reg [3:0] Q;always @ (posedge CLK)
if (RST) Q = 0; else Q = D;endmodule // reg4• On positive clock edge, either reset,
or load with new value from D• Note: Says 32-bits in tutorial, but its 4-bits
CS 61C L31 Verilog I (15) Garcia, Spring 2004 © UCB
Example page 13 Verilog Tutorial...initialbegin
CLK = 1'b0;forever#5 CLK = ~CLK;
end...• No built in clock in Verilog, so specify one• Clock CLK above alternates forever in 10 ns period: 5 ns at 0, 5 ns at 1, 5 ns at 0, 5 ns at 1, …
CS 61C L31 Verilog I (16) Garcia, Spring 2004 © UCB
Example page 14 Verilog Tutorialmodule add4 (S,A,B);• a combinational logic block that forms the sum (S) of the two 4-bit binary numbers (A and B)
• Tutorial doesn’t define this, left to the reader
• Write the Verilog for this module in a behavioral style now
• Assume this addition takes 4 ns
CS 61C L31 Verilog I (17) Garcia, Spring 2004 © UCB
Example page 14 Verilog Tutorialmodule add4 (S,A,B);input [3:0] A, B;output [3:0] S;reg S;
always @(A or B) #4 S = A + B;
endmodule• a combinational logic block that forms the sum of the two 4-bit binary numbers, taking 4 ns
• Above is behavioral Verilog
CS 61C L31 Verilog I (18) Garcia, Spring 2004 © UCB
Example page 14 Verilog Tutorial//Accumulatormodule acc (CLK,RST,IN,OUT);input CLK,RST;input [3:0] IN;output [3:0] OUT;wire [3:0] W0;add4 myAdd (.S(W0), .A(IN), .B(OUT));reg4 myReg (.CLK(CLK), .Q(OUT), .D(W0), .RST(RST));endmodule // acc• This module uses prior modules, using wire to connect output of adder to input of register
CS 61C L31 Verilog I (19) Garcia, Spring 2004 © UCB
Example page 14 Verilog Tutorialmodule accTest;reg [3:0] IN;reg CLK, RST;wire [3:0] OUT;acc myAcc (.CLK(CLK), .RST(RST), .IN(IN), .OUT(OUT));initial
beginCLK = 1'b0;repeat (20)#5 CLK = ~CLK;
end ...• Clock frequency is __ GHz?
CS 61C L31 Verilog I (20) Garcia, Spring 2004 © UCB
Example page 14 Verilog Tutorial...
initialbegin#0 RST=1'b1; IN=4'b0001;#10 RST=1'b0;
endinitial$monitor("time=%0d: OUT=%1h",
$time, OUT);endmodule // accTest• What does this initial block do?• What is output sequence?• How many lines of output?
CS 61C L31 Verilog I (21) Garcia, Spring 2004 © UCB
Finite State Machines (FSM)
• Tutorial example is bit-serial parity checker
• computes parity of string of bits sequentially, finding the exclusive-or of all the bits
• Parity of "1" means that the string has an odd number of 1's
“Even” stateOUT = 0
IN = 0 “Odd” stateOUT = 1
IN = 0
IN = 1
IN = 1
CS 61C L31 Verilog I (22) Garcia, Spring 2004 © UCB
Example page 16, Verilog Tutorial//Behavioral model of D-type flip-flop:
// positive edge-triggered,// synchronous active-high reset.module DFF (CLK,Q,D,RST);input D;input CLK, RST;output Q;reg Q;always @ (posedge CLK)
if (RST) #1 Q = 0; else #1 Q = D;endmodule // DFF• Loaded on positive edge of clock
CS 61C L31 Verilog I (23) Garcia, Spring 2004 © UCB
Example page 3, Part III Verilog Tutorial//Structural model of serial parity checker.
module parityChecker (OUT, IN, CLK, RST);output OUT;input IN;input CLK, RST;wire currentState, nextState;DFF state (.CLK(CLK), .Q(currentState), .D(nextState), .RST(RST));xor (nextState, IN, currentState);buf (OUT, currentState);
endmodule // parity
Verilog doesn’t like itwhen you feed outputsback internally…
CS 61C L31 Verilog I (24) Garcia, Spring 2004 © UCB
Peer Instruction
A. To test FSMs, you need to test every transition from every state
B. Modules must be updated with explicit calls to them, ala scheme
C. If input not explicitly set, output of CL defaults to ‘0’
ABC1: FFF2: FFT 3: FTF4: FTT5: TFF6: TFT7: TTF8: TTT
CS 61C L31 Verilog I (25) Garcia, Spring 2004 © UCB
In conclusion• Verilog describes hardware in hierarchical fashion, either its structure or its behavior or both
• Time is explicit, unlike C or Java
• Time must be updated for variable change to take effect
•monitor print statement like a debugger; display, write, strobe more normal
• Modules activated simply by updates to variables, not explicit calls as in C or Java
CS 61C L31 Verilog I (26) Garcia, Spring 2004 © UCB
Lecture over…
CS 61C L31 Verilog I (27) Garcia, Spring 2004 © UCB
Example page 3, Part III Verilog Tutorial//Test-bench for parityChecker.
// Set IN=0. Assert RST. Verify OUT=0.// IN=0, RST=1 [OUT=0]
// Keep IN=0. Verify no output change.// IN=0, RST=0 [OUT=0]
// Assert IN. Verify output change.// IN=1 [OUT=1]
// Set IN=0.Verify no output change.// IN=0[OUT=1]
// Assert IN. Verify output change.// IN=1 [OUT=0]
// Keep IN=1. Back to ODD.// IN=1[OUT=1]
// Assert RST. Verify output change.// IN=0, RST=1 [OUT=0]
• Comments give what to expect in test
CS 61C L31 Verilog I (28) Garcia, Spring 2004 © UCB
Example page 3, Part III Verilog Tutorial...
module testParity0;reg IN;wire OUT;reg CLK=0, RST;reg expect;parityChecker myParity (OUT, IN, CLK, RST);always #5 CLK = ~CLK;...• Note initializing CLK in reg declaration• No begin ... end for always since
only 1 statement
CS 61C L31 Verilog I (29) Garcia, Spring 2004 © UCB
Example page 3, Part III Verilog TutorialinitialbeginIN=0; RST=1; expect=0;#10 IN=0; RST=0; expect=0;#10 IN=1; RST=0; expect=1;#10 IN=0; RST=0; expect=1;#10 IN=1; RST=0; expect=0;#10 IN=1; RST=0; expect=1;#10 IN=0; RST=1; expect=0;#10 $finish;
endinitial$monitor($time," IN=%b, RST=%b, expect=%b OUT=%b", IN, RST, expect, OUT);endmodule // testParity0
CS 61C L31 Verilog I (30) Garcia, Spring 2004 © UCB
Example output, p. 4 Part III Verilog Tutorial5 IN=0, RST=1, expect=0 OUT=0
10 IN=0, RST=0, expect=0 OUT=020 IN=1, RST=0, expect=1 OUT=025 IN=1, RST=0, expect=1 OUT=130 IN=0, RST=0, expect=1 OUT=140 IN=1, RST=0, expect=0 OUT=145 IN=1, RST=0, expect=0 OUT=050 IN=1, RST=0, expect=1 OUT=055 IN=1, RST=0, expect=1 OUT=160 IN=0, RST=1, expect=0 OUT=165 IN=0, RST=1, expect=0 OUT=0• Output not well formated; so uses $write,
$strobe line up expected, actual outputs
CS 61C L31 Verilog I (31) Garcia, Spring 2004 © UCB
Example page 3, Part III Verilog Tutorial...
#10 $finish;end
alwaysbegin$write($time," IN=%b, RST=%b, expect=
%b ", IN, RST, expect);#5 $strobe($time," OUT=%b", OUT);#5 ;
endendmodule // testParity2•$write does not force new line, $write and $strobe only prints on
command, not on every update
CS 61C L31 Verilog I (32) Garcia, Spring 2004 © UCB
Example output, p. 7 Part III Verilog Tutorial
0 IN=0, RST=1, expect=0 5 OUT=010 IN=0, RST=0, expect=0 15 OUT=020 IN=1, RST=0, expect=1 25 OUT=130 IN=0, RST=0, expect=1 35 OUT=140 IN=1, RST=0, expect=0 45 OUT=050 IN=1, RST=0, expect=1 55 OUT=160 IN=0, RST=1, expect=0 65 OUT=0•$write does not force new line, $write and $strobe only prints on
command, not on every update
CS 61C L31 Verilog I (33) Garcia, Spring 2004 © UCB
Peer Instruction• Suppose writing a MIPS interpreter in Verilog. Which sequence below is best organization for the interpreter?
I. A repeat loop that fetches instructions
II. A while loop that fetches instructions
III. Increments PC by 4
IV. Decodes instructions using case statement
V. Decodes instr. using chained if statements
VI. Executes each instructionA. I, IV, VI
B. II, III, IV, VI
C. II, V, VI, III
D. IV, VI, III, II
E. V, VI, III, I
F. VI, III, II
CS 61C L31 Verilog I (35) Garcia, Spring 2004 © UCB
Verilog Odds and Ends• Memory is register with second dimension
reg [31:0] memArray [0:255];
• Can assign to group on Left Hand Side{Cout, sum} = A + B + Cin;
• Can connect logical value 0 or 1 to port via supply0 or supply1
• If you need some temporary variables (e.g., for loops), can declare them as integer
• Since variables declared as number of bits, to place a string need to allocate 8 * number of characters
reg [1 : 6*8] Msg; Msg = ”abcdef”;
CS 61C L31 Verilog I (36) Garcia, Spring 2004 © UCB
ROM Module used for MIPS Interpreter 1/2//Behavioral model of Read Only Memory:// 32-bit wide, 256 words deep,// asynchronous read-port,// initialize from file on positive// edge of reset signal, by reading// contents of "text.dat" interpeted// as hex.//
...
CS 61C L31 Verilog I (37) Garcia, Spring 2004 © UCB
ROM Module used for MIPS Interpreter 2/2module ROM (RST,address,readD); input RST; input [31:0] address; output [31:0] readD; reg [31:0] readD; reg [31:0] memArray [0:255]; always @ (posedge RST) $readmemh("text.dat", memArray); always @ (address) readD = memArray[address[9:2]];endmodule // ROM• 32-bit registers, 256 word x 32 bit memory• Loads from file on reset, address => readD
CS 61C L31 Verilog I (38) Garcia, Spring 2004 © UCB
Register File used for MIPS Interpreter 1/4//Behavioral model of register file:// 32-bit wide, 32 words deep,// two asynchronous read-ports,// one synchronous write-port.// Dump register file contents to console// on positive edge of dump signal.//
CS 61C L31 Verilog I (39) Garcia, Spring 2004 © UCB
Register File used for MIPS Interpreter 2/4module regFile (CLK, wEnb, DMP, writeReg, writeD, readReg1, readD1, readReg2, readD2); input CLK, wEnb, DMP; input [4:0] writeReg, readReg1,
readReg2; input [31:0] writeD; output [31:0] readD1, readD2; reg [31:0] readD1, readD2; reg [31:0] array [0:31]; reg dirty1, dirty2; integer i;• 3 5-bit fields to select registers: 1 write register, 2 read register
CS 61C L31 Verilog I (40) Garcia, Spring 2004 © UCB
Register File used for MIPS Interpreter 3/4always @ (posedge CLK) if (wEnb) if (writeReg!=4'h0) begin array[writeReg] = writeD; dirty1=1'b1; dirty2=1'b1; end
always @ (readReg1 or dirty1) begin
readD1 = array[readReg1];dirty1=0;
end
CS 61C L31 Verilog I (41) Garcia, Spring 2004 © UCB
Register File used for MIPS Interpreter 4/4 always @ (readReg2 or dirty2)
beginreadD2 = array[readReg2];dirty2=0;
end always @ (posedge DMP) for (i=0; i<32; i=i+1) $display("r%0d:%h", i, array[i]); initial array[0]=0;endmodule // regFile• Why dirty1, dirty2? Why initial array[0]=0? Why
display if DMP? Why check !=0 write?
CS 61C L31 Verilog I (42) Garcia, Spring 2004 © UCB
Your feedback (162 submissions) 1/2
• Average # of hours spent doing homework: 5.0
• Average # of hours spent doing labs: 2.2
• Average # of hours spent reading: 3.2
• Average # of hours spent doing projects: 12.4
• Average number of hours spent on CS61C: 18
• Fraction of people that feel like they don't get help in lab: 32%
• Fraction of people that have a hard time getting checked off in lab: 13.75%
CS 61C L31 Verilog I (43) Garcia, Spring 2004 © UCB
Your feedback (162 submissions) 2/2
• % of people that find the online lecture notes useful: 92%
• “How useful are peer instruction questions?(1 least, 4 most)”: 3.3
• “How useful are reading quizzes?(1 least, 4 most)”: 2.9
• “Lecture covers too (1 little, 4 much) material”: 3.1
• “Lecture moves too (1 slow, 4 fast) fast”: 3.2
• "Lecture length is (1 too long, 4 just fine)”: 2.7
• “I am (1 not at all, 4 extremely) confident”: 2.2