CS440-01 R223.1337en Spare Parts Catalog

spare parts catalog Doc. no. R 223.1337 en

SANDVIK CS440:01

This document is valid for:

Serial no. / Machine no. Sign.

SANDVIK CS440:01 © Copyright 2010 Sandvik SRP AB.All rights reserved. No parts of this document may be reproduced or copied in any form or by any means without written permission from Sandvik SRP AB. All data and information in this manual may be changed without further notice. Reservations for misprints.

Document number: R 223.1337 Issue: 20120306Version: 03

SandvikStationsplan, SE-233 81 Svedala, SwedenTel: +46 (0)40 409000, Fax: +46 (0)40 409260www.sandvik.com

SPC Sandvik CS440:01

1. Cone crusher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. Wearing plates in bottom shell . . . . . . . . . . . . . . . . . . . . . . 11

3. Feed hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4. Rubber compression mounting . . . . . . . . . . . . . . . . . . . . . 15

5. Hydroset system (accumulator) . . . . . . . . . . . . . . . . . . . . 17

6a. Overpressure supply system, blower . . . . . . . . . . . . . . 19

6b. Overpressure supply system, compressed air . . . . . . . 21

7. Belt driving SPC, 4-pole, 50 Hz . . . . . . . . . . . . . . . . . . . . . . 23

8. Belt driving 8V, 6-pole, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . 25

9. Sign assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

10. Service/Repair kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3© 2010 Sandvik SRP AB Doc. no. R 223.1337 Ver. 03


This page is intentionally left blank

4 © 2010 Sandvik SRP ABDoc. no. R 223.1337 Ver. 03

SPC Sandvik CS440:01 452.0288

1. Cone crusher



Cat No Qty Part number Alternative Description Remarks1005-0 1 452.0230-901 Bottom Shell

1006-0 2 442.7201-00 Cover

1006-1 4 843.1267 Stud screw,SMS1460,M12×45

1006-2 4 847.0147-00 Washer BRB 13×24 HB200 ISO 7089

1006-3 4 845.0030-00 Lock nut M12 8 FZB ISO 7040

1010-1 1 442.7140-00 Liner-Pin Shaft Arm

1010-2 2 442.7141-00 Liner-Narrow Arm

1015-0 1 900.0027-00 Elbow A4/90 3” A4 SMS 435

1200-0 1 442.7146-01 Bottom shell bushing

1280-0 1 853.0464-00 Pin CP 12M6×12 SMS 2374

1285-0 1 900.0921-00 Swivel branch tee adapter 3/4”

1285-1 1 900.1412-00 “Pipes Pipe KR 3/4”×70”

1285-2 1 900.0276-00 Cover 3/4”

1320-0 1 452.0243-901 Liners in Bottom Shell

1400-0 1 442.7106-01 Dust collar

1400-1 4 840.0634-00 Screw M6S 16×25 8.8 ISO 4017

1401-0 1 442.7109-01 Ring

1404-0 1 853.0464-00 Pin CP 12M6×12 SMS 2374

1405-0 12 840.1281-00 Screw M6S 16×80 8.8 ISO 4017

1405-2 12 847.0016-00 Washer BRB 17×30 HB200 ISO 7089

1410-0 1 442.7110-01 Locating bar

1411-0 1 442.7168-01 Shim T=0.1

1 442.7168-02 Shim T=0.5

1 442.7168-03 Shim T=0.7

1 442.7168-04 Shim T=1.0

1412-0 3 841.0019-00 Screw MC6S 10×40 12.9

1430-0 1 442.7170-01 Gasket

1450-0 1 442.7108-01 Seal ring inner

1505-0 8 840.0071-00 Screw M6S 16×65 8.8 ISO 4014

1505-2 8 847.0060-00 Washer TBRSB 17×42

1540-0 16 840.1073-00 Screws M6S 42×220 8.8

1540-1 16 845.0322-00 Nut M6M M42 8 FZB ISO 4032

1540-2 16 847.0171-00 Washer BRB 43×80 HB 200 SS 3576

1540-5 16 899.0278-00 Protective Cap SW65 2 H20

1550-0 4 442.9530-01 Screw M6S 42×100

1550-5 4 899.0278-00 Protective Cap SW65 2 H20

1805-0 1 442.8068-01 Eccentric

1810-0 1 442.8067-01 Eccentric bushing 20+25+30+36

1815-0 1 442.7142-01 Hub

1816-0 1 442.7169-00 Ring



1817-0 8 840.1157-00 Screws M6S 12×40 10.9 ISO4017

1817-2 8 847.0147-00 Washer BRB 13×24 HB200 ISO 7089

1820-0 1 442.9609-01 Key R25×14×250

1825-0 5 841.0027-00 Screw MC6S 12×70 12.9

1825-1 7 841.0025-00 Screw MC6S 12×50 12.9

1825-2 12 847.0180-00 Washer DIN 137 B 13×24

1850-0 1 442.7093-00 Gear and pinion set

1855-0 1 442.7171-01 Key

1880-0 1 442.7107-01 Eccentric wearing plate

1885-0 8 853.0646-00 Pin Prym N 16×45

2005-0 1 442.7163-01 Hydroset cylinder

2020-0 16 840.0671-00 Screw M6S M24×90 8.8 ISO 4014

2020-2 16 847.0124-00 Washer BRB 25×45 HB200 SS 3576

2050-0 1 442.7166-01 Hydroset cylinder bushing

2055-0 1 840.0019-00 Screws M6S 8×12 8.8

2055-0 1 841.0019-00 Screw MC6S 10×40 12.9

2055-2 1 847.0012-00 Washer BRB 8.4×16 HB200 ISO 7089

2140-0 1 873.0892-00 Seals O-ring 532.26×6.99

2205-0 1 442.9672-00 Piston

2225-0 1 853.0119-00 Pin CP 25m6×60 SMS 2374

2260-0 1 442.7122-01 Piston wearing plate

2280-0 1 442.7121-01 Step washer

2305-0 1 442.7112-00 Chevron packing

2400-0 1 442.7167-01 Packing clamp plate

2401-0 8 841.0266-00 Screw MC6S 12×25 8.8

2505-0 1 442.9663-00 Hydroset cylinder cover

2515-0 13 840.0671-00 Screw M6S M24×90 8.8 ISO 4014

2515-1 2 840.0676-00 Screw M6S 24×140 8.8 ISO 4017

2515-2 15 847.0124-00 Washer BRB 25×45 HB200 SS 3576

2530-0 1 902.0605-00 Air Bleeder valve

2540-0 1 873.0835-00 Seals O-ring 419.3×5.7 SMS1586

2540-1 1 873.1276-00 Seals O-ring 453×5.7 SMS 1586

2560-0 1 442.8783-01 Plug

2560-1 1 873.0111-00 O-ring 44.2×3 SMS 1586

2560-2 6 840.0023-00 Screws M6S 8×25 8.8

2560-3 6 847.0012-00 Washer BRB 8.4×16 HB200 ISO 7089

2560-4 4 840.1010-00 Screws M6S 12×16 8.8

3001-0 1 442.9966-00 Pinion shaft housing assembled

3005-0 1 442.7506-01 Pinion shaft housing

3030-0 1 442.7136-01 Gasket T=0.5

1 442.7136-03 Gasket T=1.5

1 442.7136-02 Gasket T=0.8

3050-0 – – Pinion Please refer to Cat No 1850-0

3070-1 1 868.0282-00 Bearings Spherical Roller 23122 CC/W33/C3

3070-2 1 868.0804-00 Tapered roller bearing 452322 M2/W502

3090-1 1 442.7130-01 Spacer inner

3090-2 1 442.7131-01 Spacer outer

3120-1 1 873.0779-00 Seals O-ring 84.1×5.7 SMS 1586

3120-2 1 873.0399-00 Seals O-ring 99.1×5.7

3170-1 1 873.1208-00 Oil seal ring 130×160×12

3170-2 1 873.1208-00 Oil seal ring 130×160×12

3190-1 1 442.9684-01 Bearing cover inner

3190-2 1 442.7133-01 Bearing cover outer

Cat No Qty Part number Alternative Description Remarks



3210-0 6 840.0045-00 Screw M6S 12×30 8.8 ISO 4017

3210-2 6 847.0147-00 Washer BRB 13×24 HB200 ISO 7089

3220-0 6 840.0066-00 Screw M6S M16×40 8.8 fzb ISO4017

3220-2 6 847.0016-00 Washer BRB 17×30 HB200 ISO 7089

3240-1 1 442.7134-01 Gasket

3240-2 1 442.7135-01 Gasket T=0.5

1 442.7135-02 Gasket T=0.8

3330-0 1 853.0590-00 Spring Pin Prym N 8×28

3505-0 1 442.9937-01 Pinion shaft

3515-0 1 857.0337-00 Key 22×14×95 SMS2307

3575-0 1 900.0022-00 Elbow 3/4 A4 SMS 435

3585-0 1 900.2026-00 Magnetic plug 0606-12

3585-1 1 873.0385-00 Tredo Nr.20 3/4”

3590-0 1 442.7577-01 Oil level plug

3590-1 2 873.0108-00 Seals O-ring 34.2×3 SMS 1586

3590-2 1 442.7578-01 Pipe

3650-0 1 855.0108-00 3_Retaining Rings Sga 85

3710-0 2 840.1063-00 Screw M6S 16×120H 8.8

3710-1 2 845.0009-00 Nut M6M M16 8 FZB ISO 4032

4001-0 1 452.1699-901 Main shaft assembly excluding mantle

4005-0 1 452.1635-901 Headcenter - main shaft

4025-0 1 442.7117-01 Main shaft sleeve

4035-0 1 853.0119-00 Pin CP 25M6×60 SMS 2374

4075-0 1 442.7120-01 Main shaft step

4135-0 1 855.0026-00 Retaining Ring Sga 100 SS1581

4175-0 1 442.8089-01 Mantle A, M1

1 442.8070-01 Mantle B, M1

4175-9 70 831.0016-00 Casting compound (kg)

50 831.0016-00 Casting compound (kg)

4205-0 1 442.7105-00 Head nut with burn ring

4205-1 1 442.8333-01 Inner head ring

4205-2 1 442.7115-01 Burn ring

4305-0 1 442.7102-01 Dust seal ring

4350-0 1 442.7103-01 Retaining ring

4355-0 1 442.7523-01 Retainer

4355-1 1 442.7524-01 Scraper

4365-0 11 840.0069-00 Screw M6S 16×55 8.8 ISO 4017

4365-1 1 840.0071-00 Screw M6S 16×65 8.8 ISO 4014

4365-2 12 847.0016-00 Washer BRB 17×30 HB200 ISO 7089

5001-0 0 442.8093-00 Top shell assembly excluding crusher ch.

5005-0 1 442.8059-01 Top shell EC2

5110-0 6 442.9036-01 Liner

5112-0 20 452.6197-001 Dowel 2172-00 D 36×32

5150-0 2 442.8075-01 Arm shield

5155-0 4 442.8077-01 Fixing pin

5155-1 4 442.8078-01 Bumper

5155-2 2 442.8079-01 Bumper

5220-0 2 900.1262-00 Elbow Adapter G 1/4 B×R 1/4

5220-1 2 900.1030-00 Bushing RI-08-04 1/2”-1/4”

5240-0 2 650.0086-11 Hose SAE 100 R1AT 1/4"×650"

5253-0 1 914.0093-00 Lubrication Nipple AH R 1/4”

5275-0 2 442.8090-01 Bracket




5285-0 4 840.0021-00 Screw M6S M8×20 8.8 fzb ISO 4017

5313-0 1 900.0243-00 Wrought iron pipe fittings Socket Rp 1/4

5313-1 2 900.0652-00 Adapter G 1/4 B×G 1/4 B

5650-0 1 442.9164-00 Spider cap

5650-1 1 912.0114-00 Air Filter P10102 R1/4”

5650-2 2 900.0134-00 Bushing 3/8"×1/4X"

5650-3 1 900.2008-00 2_Pipe couplings Elbow 45 SMS 453-10

5651-0 1 873.0838-00 Seals O-ring 499.3×5.7 SMS 1586

5655-0 4 840.0079-00 Screw M6S 20×70 8.8 ISO 4017

5655-2 4 847.0165-00 Washer TBRB 21×36 1370 SS 1466

5675-0 1 442.9408-01 Spider bushing

5685-0 6 840.0652-00 Screw M6S 20×90 8.8 ISO 4017

5685-2 6 847.0132-00 Washer BRB 21×36 HB200 SS 3576

5705-0 1 442.7193-01 Seals O-ring Oil seal ring

5750-0 1 900.0981-00 Plug BSPT 1” hexagon

6001-0 1 442.8111-00 Crusher chamber EC

6001-1 1 442.8112-00 Crusher chamber C

6001-2 1 452.1202-901 Crushing Chamber MC

6305-0 1 452.0273-001 Concave ring MC

1 442.8114-00 Concave ring lower M1

1 442.8098-00 Concave ring lower M1

6390-0 8 452.0274-001 Concave MC

8 442.8115-00 Concave upper

8 442.8099-00 Concave upper

6390-9 380 831.0016-00 Casting compound (kg)



8401-0 1 442.8082-00 Hydroset system

8950-0 1 442.7255-92 Wrench and tool set

1 442.7255-91 Wrench and tool set

1 442.7255-90 Wrench and tool set







2. Wearing plates in bottom shell

Cat. No. Qty. Part number Alternative Description Remarks452.5778-901 Bottomshell arm liner kit

1010-1 1 442.7140-00 Liner-Pin shaft arm Included in Bottom shell arm liners kit

1010-2 2 442.7141-01 Liner-Narrow arm

452.0243-00 Wearing plates complete set

1320-1 1 442.8794-01 Wearing plates Included in Wearing plates complete set

1320-2 4 442.8798-01 Wearing plates

1320-3 2 442.8797-01 Wearing plates

1320-4 2 442.8796-01 Wearing plates

1320-5 2 442.8795-01 Wearing plates

1320-6 2 452.0239-001 Wearing plates

1320-7 1 452.0238-001 Wearing plates

12 442.8799-06 Rod 1312-00 4-kt 12×60

2 840.0049-00 Screw M6S 12×50 8.8 ISO 4014

6 847.0059-00 Washer TBRSB 13.5×36 1370

1320-2 1320-1 1010-11320-3

1320-4

1320-5

1320-6

1320-4 1320-3 1320-3 1320-71010-2 1320-2






3. Feed hopper

Cat. No. Qty. Part number Alternative Description Remarks1 442.8106-00 Feed hopper complete Consist of:

1 1 442.8105-00 Feed hopper

2 12 840.0080-00 Screw M6S 20×80 8.8 ISO 4014

3 12 845.0010-00 Nut M6M0 8 ISO 4032

4 12 847.0132-00 Washer BRB 21×36 HB 200

2, 3, 4

1






4. Rubber compression mounting

Pos No Qty. Part number Alternative Description Remarks442.6635-00 Rubber compression mounting for crusher

1 1 845.0387-00 Nut lock ISO 7040 M24 8 FZB

2 1 847.0124-00 Washer BRFB 25×45

3 1 442.9779-00 Top plate

4 1 864.0046-00 Rubber compression mounting SAW 150 B

5 8 840.0044-00 Screw M6S12×25

6 8 847.0147-00 Washer BRB 13×24

7 1 442.9780-00 Fixing plate, lower

Pos No Qty. Part number Alternative Description Remarks442.6635-90 Rubber compression mountings for crusher on subframe

4 1 864.0070-00 Rubber compression mounting SAW 150 B

5 8 840.0044-00 Screw M6S12×25

6 8 847.0147-00 Washer BRB 13×24

7 1 442.9780-01 Fixing plate, lower

8 4 840.0048-00 Screw M6S 12×45 8.8 ISO 1417

9 4 845.0030-00 Nut M6MN 12 8 FZB ISO 7040

7

1, 2

3

45, 6

6, 8, 94

5, 67






5. Hydroset system (accumulator)

Pos. No. Qty. Part number Alternative Description Remarks01 1 442.6908-01 Bushing 1914-04 R 2”×1

02 1 873.0390-00 Seal ring TREDO 30

03 1 900.0648-00 Adapter R1”×3/4”

04 1 873.0386-00 Seal ring TREDO 23

05 1 442.8080-01 Connection piece D 90×90 R 3/4

06 1 900.0655-00 Adapter R 3/4”

07 2 873.0385-00 Seal ring TREDO 20

08 1 650.0154-00 Hose SAE R2AT 3/4”×1050

09 1 442.2100-01 Bracket 1312-00

10 1 900.0746-00 Clamp RSGU 11 1100 30/15

11 1 840.0013-00 Screw M6S 6×25 8.8 ISO 4017

12 1 845.0004-00 Nut M6M 6 8 ISO 4032

13 1 442.8645-00 Hose guard

14 1 900.0810-00 Bushing RED R 3/4”×R1/2”

15 1 902.0605-00 Bleeder valve UV 121

25 4 847.0060-00 Washer TBRSB 17×42 t=8

1 919.0231-00 Adapter ISO228-G2A - ISO228-G2A Between check valve and accumulator






6a. Overpressure supply system, blower

2 3

4

5

1

6 5 4

785

910

11

5

12

4

Pos. No. Qty. Part number Alternative Description Remarks– 1 442.8642-00 Motor 400 V, 50 Hz.

Other motors available according to order

Over pressure unit, blower Kit, contains the following parts:(except the filter cartridge)

11 912.0138-00 Air filter Purolator PI 0154 Contains cover and filter cartridge

1 912.0139-00 Filter cartridge Not included in kit

2 1 900.0108-00 Wrought iron pipe fittings 1×3/4

3 1 900.0022-00 Elbow A4 Zn DN20 zinced

4 4 900.1424-00 Hose coupling 3/4

5 4 900.1358-00 Hose clips D 28

6 1 819.0187-00 Hose pneumatic 1" PVC

7 1 900.0005-00 Elbow A1 3/4" ISO 49

8 2 900.1139-00 Clip RSGU 1.22/15

9 1 900.0365-00 Hexagon nipple R 3/4

10 1 900.0040-00 Tee B1 3/4" ISO 49

11 1 900.0020-00 Elbow 1/2" A4 ISO 49

12 1 442.9325-00 Overpressure fan






6b. Overpressure supply system, compressed air

8 7 6

11121314

1516

17

7 6 7

4

10

1 2 3 4 5

6

1318

919

79

Pos. No. Qty. Part number Alternative Description Remarks– 1 442.8642-90 Motor 400 V, 50 Hz.

Other motors available according to order

Over pressure unit, compressed air Kit, contains the following parts:

1 1 912.0113-00 Air filter 504-2S 5 Micron

2 1 900.0169-00 Hexagon nipple N8 DN8/8 zinced

3 1 902.0645-00 Regulator 216-2-8

4 2 900.0209-00 Plug R 3/8 T8 FZV ISO 49

5 1 900.0022-00 Elbow A4 Zn DN20 zinced

6 4 900.1424-00 Hose coupling 3/4

7 4 900.1358-00 Hose clips D 28

8 1 819.0187-00 Hose pneumatic 1" PVC

9 1 923.0267-00 Pressure gauge 2060 D100 0–1 000 Pa

10 1 126.0678-901 Set of signs

11 1 900.0005-00 Elbow A1 3/4" ISO 49

12 1 900.0172-00 Nipple N8 3/4" ISO 49

13 2 900.0054-00 Tee B1 3/4×3/8 ISO 49

14 2 900.1139-00 Clip RSGU 1.22/15

15 1 900.0365-00 Hexagon nipple R 3/4

16 1 900.0040-00 Tee B1 3/4" ISO 49

17 1 900.0020-00 Elbow 1/2" A4 ISO 49

18 1 900.0182-00 Nipple N8 3/4×1/4 ISO 49

19 1 900.0180-00 Nipple N8 1/2×1/4 ISO 49






7. Belt driving SPC, 4-pole, 50 Hz

Pos No Qty. Part number Alternative Description Remarks1 1 879.0359-00 V-belt Pulley 375 MGT 125 10×SPC

2 1 869.0235-00 Bushing MGT No. 125 Di=100

3 – – Screw Included in bushing

4 1 857.0336-00 Key T28×16×110 SMS 2307

5 1 442.9951-00 Distance D115/100.5×58

6 1 442.7238-01 Washer 2142-50 D120/18×15

7 1 847.0016-00 Washer BRB 17×30 HB 200 ISO 7089

8 1 840.0065-00 Screw M6S M16×35 8.8 fzb ISO 4017

9 1 879.0511-00 V-belt Pulley 355 MGT 125 10×SPC

10 1

869.0261-00 Di=80

Bushing MGT No. 125 According to order869.0278-00 Di=85

869.0295-00 Di=90

869.0283-00 Di=95

11

1 875.0276-00 2650, standard C-C 767

V-belt SPC According to order875.0249-00 4500, standard

C-C 1693

A

A

11

B

B

9

B-B

10

A-A

4 2 1

56

7, 8

3






8. Belt driving 8V, 6-pole, 60 Hz

Pos No Qty. Part number Alternative Description Remarks1 1 869.0329-00 Bushing QD M100 mm Di=100

2 1 442.7238-01 Washer 2142-50 D 120/18×15

3 1 847.0016-00 Washer BRB 17×30 HB 200 ISO 7089

4 1 840.0067-00 Screw M6S M16×45 8.8 fzb ISO 4017

5 1 879.0617-00 V-belt Pulley QD Dy17” 10×8V

6 1

869.0338-00 M3-38 Di=3⅜

Bushing QD M3 According to order869.0339-00 M3-38 Di=3⅝

869.0333-00 M3-38 Di=3⅞

7 1 879.0625-00 V-belt Pulley QD Dy 19” 10×8V

8 1

875.0366-00 1500, standard C-C 1195

V-belt 8V According to order875.0172-00 1900, standard

C-C 1703

9 1 857.0356-00 Key T 28×16×140 SMS 2307

A

A

A-A

B

B B-B

7 6

8

5 9 1

23, 4






9. Sign assembly

Pos. No. Qty. Part number Alternative Description Remarks1 2 126.0423-001 Sign product name

2 2 126.0444-001 SANDVIK logotype silver 120

3 1 126.0383-001 Risk of crushing

4 4 885.0249-00 Signs center of gravity

5 4 126.0384-001 Warning flying fragments

6 1 126.0385-001 Warning sign read manual

7 1 126.5007-01 Identification plate

8 1 885.0267-00 Warning sign Danger

9 4 885.0262-00 Lifting plate chain Placed on front and back of both arms inside crusher

53

6

5

5

2

44 4

1

5

2 1

4

5

172

7

8

3, 6

8

9






10. Service/Repair kit

(Continued)

Locating bar kit 452.5798-901Pos No Qty. Part number Alternative Description Remarks1410-0 1 442.7110-01 Locating bar

1411-0 1 442.7168-01 Shim t=0.1

1 442.7168-02 Shim t=0.5

1 442.7168-03 Shim t=0.7

1 442.7168-04 Shim t=1.0

1412-0 3 841.0019-00 Screw MC6S 10×40 12.9

Pinionshaft housing repair kit 452.5575-901Cat No Qty. Part number Alternative Description Remarks3030-0 1 442.7136-01 Gasket T=0.5

1 442.7136-02 Gasket T=0.8

1 442.7136-03 Gasket T=1.5

3070-1 1 868.0282-00 Bearing

3070-2 1 868.0804-00 Bearing

3090-1 1 442.7130-01 Spacer

3090-2 1 442.7131-01 Spacer

3120-1 1 873.0779-00 O-ring

3120-2 1 873.0399-00 O-ring

3170-1, -2 2 873.1208-00 Sealing ring

3240-1 1 442.7134-01 Gasket

3240-2 1 442.7135-01 Gasket

3240-2 1 442.7135-02 Gasket

3585-1 1 873.0385-00 Sealing Ring Tredo 20

3590-1 2 873.0108-00 O-ring

Bottomshell arm liner kit 452.5778-901Cat No Qty. Part number Alternative Description Remarks1010-1 1 442.7140-00 Pin shaft arm liner

1010-2 2 442.7141-00 Narrow arm liner



Bottomshell liner kit 452.0243-00Cat No Qty. Part number Alternative Description Remarks1320-1 1 442.8794-01 Wearing plates

1320-2 4 442.8798-01 Wearing plates

1320-3 2 442.8797-01 Wearing plates

1320-4 2 442.8796-01 Wearing plates

1320-5 2 442.8795-01 Wearing plates

1320-6 2 452.0239-001 Wearing plates

1320-7 1 452.0238-001 Wearing plates

12 442.8799-06 Rod 1312-00 4-kt 12×60

2 840.0049-00 Screw M6S 12×50 8.8 ISO 4014

6 847.0059-00 Washer TBRSB 13.5×36 1370

Filter kit 452.5543-901Pos No Qty. Part number Alternative Description Remarks

4 912.0126-00 Filter HC69

2 912.0129-00 Filter cartridge HC2

1 912.0139-00 Filter cartridge HC2 852516 MIC

1 912.0155-00 Filter cartridge HC2 852514 MIC


Date post:	03-Jan-2016
Category:	Documents
Upload:	luis-aguilera-s
View:	621 times
Download:	67 times

CS440-01 R223.1337en Spare Parts Catalog

Documents