CSR SeRieS MeDiUM-DUty
CUStOM welDeDhyDRaUliC CylinDeRS
Bore Diameters:2.50” (63.5mm)2.75” (69.9mm)3.00” (76.2mm)3.25” (82.6mm)
4.00” (101.6mm)
For Working Pressures to 3,400 Psig (235 Bar)
®
Energy®’s CSR Series Welded Cylinders Feature:
SAE Ports
Steel Base Clevis Long Life Seal
with Nitrile Ex-pander Ring
Hard Chrome Plated 1045 Steel Rod
65-45-12 Ductile Iron Rod Clevis
St 52.3 Steel TubingDOM Honed or Skive Burnished to 4-10 RMS
Ductile Iron Rod Guide
CSR hyDRaUliC CylinDeR DeSign
2.
CSR welDeD COnStRUCtiOn
CSR Cylinder DimensionsBore Diameter Rod Diameter
2.50” (63.5 mm) 1.125” (28.6 mm)
2.75” (69.9 mm) 1.250” (31.8 mm)
3.00” (76.2 mm) 1.250” (31.8 mm)
3.25” (82.6 mm) 1.250” (31.8 mm)
4.00” (101.6 mm) 2.50” (63.5 mm)
CSR DeSign OptiOnS
3.
Base End
Rod End
Clevis Clevis
Drill Hole
Cross Tube Cross Tube
Flange
Plain Plain
Threaded Threaded
Trunnion Trunnion
The standard Energy® cylinder breathers contain a screen element retained by a star washer. Efficiency is improved by periodically putting several drops of oil in the breather hole.
Clevis pins, in four different lengths, are designed for all types of hydraulic applica-tions. These pins are plated to resist rust or corrosion. They improve alignment and reduce shaft and seal wear caused by worn pins.
Part number 17989A contains a sintered element with a 10 micron filtration rating. The other breathers do not carry a filtration rating.
CylinDeR bReatheRS
CleviS pinS
NOTE: Custom base and rod ends, as well as other custom cylinder features, may be available upon request. Please contact our factory for additional information.
Drill Hole
Pin Eye Pin Eye
Flange
Comes complete with clip.
Extra clips bulked packedat 150.
Clevis Pins Specifications
Pin & ClipStandard
Packaging A B C
1” (25.4 mm)
35890B 3.1” (78 mm) 2.5” (64 mm) 2.25” (57 mm) 25
35891B 3.3” (84 mm) 2.7” (69 mm) 2.5” (64 mm) 25
35892B 3.8” (97 mm) 3.2” (81 mm) 3” (76 mm) 25
NOTE: Separate clip is Energy p/n 35879X
0.148 WIRE DIAMETER
0.750 DIA.INSIDE OF EYE
2.938
0A002694
0A002696
0A009431 9/16-18UNF (SAE-6 ORB)
3/4-16UNF (SAE-8 ORB)
3/4-18UNF (SAE-8 ORB)
B1
B2
B3
B4
B5
B7
B8
B9
R1
R2
R3
R4
R5
R7
R8
R9
©2011 Energy® Manufacturing Company, Inc. Form No. CSR (Rev. 5/11)
All Energy® welded cylinders are custom-made. Please complete and return the following sheet so that we can provide you with the best cylinder for your application.
Custom Quotation request FormThis form must be filled out in its entirety before a welded cylinder quotation can be prepared. Unless noted otherwise by the customer,Energy® Manufacturing will use the following parameters with respect to the processing of this request: 1. The oil temperature in the cylinder will be 170° Fahrenheit (77° Celsius) or less. 2. The rod speed will be 50 feet per minute (15.2 meters per minute) or less. 3. System filtration will be 20 micron or better. 4. The fluid used is SAE 20 (ISO VG68) or less-viscous petroleum-based fluid and is non-foaming type for hydraulic use. 5. Mount center-to-center and stroke dimensions are +/- 1/8” (+/-3.2 mm). 6. The cylinder is not used in a corrosive environment.
PURPOSE OF QUOTE: ________________________________________________ QUOTE DEADLINE DATE: ________________________
CUSTOMER DATA Customer name: _____________________________________________________________ Customer part number: ___________________ Address: ____________________________________________________________________________________________________________ City, State or Province, Zip or Postal Code, Country: __________________________________________________________________________ Telephone number: _________________________________________ Purchasing contact: ________________________________________ Fax number: ______________________________________________ Engineering contact: _______________________________________ E-mail: ___________________________________________________ CYLINDER DATA All welded cylinder quotation requests should be accompanied by a blueprint or sketch and the following data should be completed. Cushioned cylinder requests must include pump flow to cylinder, weight of load, and details of the linkage between cylinder and load. Bore size: _________________________ Mountings: Stroke length: ______________________ Base: _________________________________________________ Rod diameter: ______________________ Rod: _________________________________________________ Retracted pin center-to-center length: __________________ Finish: Port type(s) (examples: NPT, NPTF, SAE O-Ring, Acrylic Water-Based Primer Paint 4-Bolt Flange, etc.) _______________________________ (please specify color): _________________________________ Port size(s): ______________________________________ Acrylic Water-Based Finish Paint Mounting pin diameter(s): ___________________________ (please specify color): _________________________________ Test requirements: Other Painting (please specify type and color): _________________ ( ) Standard 100% air test ( ) 100% Hydraulic test Clear Rust-Preventative Coating: ___________________________ None: ________________________________________________
QUOTATION DATA Annual Usage: ____________________________________________ Release Quantity: __________________________________________ Target Price: _____________________________________________
APPLICATION DATA Type of machine (crane, combine, etc.): _________________________ Primary cylinder effort will be to ( ) push load _______________________________________________________ ( ) pull load ( ) both push and pull load Will cylinder be used to lift people? _____________________________ Cylinder is ( ) double acting ( ) single acting Type of function (hoist, swing, steering, etc.): _____________________ Cylinder is mounted ( ) vertically ( ) horizontally _______________________________________________________ ( ) swings through arc with mechanism Estimated cycles per year: ___________________________________ Does cylinder always reach full extend or retract Pressure values: position? _______________________________________________ Operating: _______________________________________________ Is cylinder subjected to high overrunning loads?__________________ Peak: ___________________________________________________ Is cylinder subjected to side loading? __________________________ Main system relief: _________________________________________ Is cylinder barrel braced to restrict buckling? ____________________ Operating flow range: _______________________________________
S003 7/05
CUStOM qUOtatiOn ReqUeSt
00.336.1
Energy® Mfg. Co., Inc.
ISO 9001:2008Energy® is a member of:
• NFPA (National Fluid Power Association)
204 Plastic Lane • Monticello, IA 52310-9472 • USAPhone: (319) 465-3537 • Fax: (319) 465-5279 • Web Site: www.energymfg.com • E-mail: [email protected]
ENERGYManufacturing Company, Inc.
®
