COOPER LIGHTING, DAYBRITE, AND HUBBELL LIGHTING SHALLBE ACCEPTABLE. OTHER MANUFACTURERS MUST FOLLOWTHE GUIDELINES IN ACCORDANCE WITH THE PRODUCTSUBSTITUTION SECTION OF THE SPECIFICATIONS FORAPPROVAL BEFORE BID DATE. ENGINEER SHALL HAVE FINALAPPROVAL OF ALL LIGHT FIXTURE SUBSTITUTIONS.
2. MOUNTING HEIGHT SHALL BE MEASURED FROM THEFINISHED FLOOR LEVEL TO THE BOTTOM OF THE FIXTURE.
3. PROVIDE BATTERY TO SUPPLY EMERGENCY LIGHTING FOR 90MINUTES AS REQUIRED BY NFPA 101 - LIFE SAFETY CODE.
4. PROVIDE INTEGRAL BUTTON-TYPE PHOTOELECTRICCONTROLLER.
5. LED DRIVER CAPABLE OF DIMMING USING 0-10V DIMMERSWITCH.
GENERAL ELECTRICAL NOTES25. LAMPS AND LIGHTING FIXTURES SHALL BE AS DESCRIBED IN
LIGHT FIXTURE SCHEDULE ON THE DRAWINGS. PROVIDELAMPS IN ALL LIGHT FIXTURES.
26. ALL LINEAR FLUORESCENT LAMPS SHALL BE T-8,LOW-MERCURY BASED ON TCLP TESTING, A COLORTEMPERATURE OF 3500°K, AND A COLOR RENDERING INDEX(CRI) OF 82, AS MANUFACTURED BY PHILIPS, GE, OR OSCRAMSYLVANIA.
27. ALL LINEAR FLUORESCENT LIGHT FIXTURES SHALL HAVEELECTRONIC BALLASTS AS MANUFACTURED BY ADVANCE,UNIVERSAL, OR OSCRAM SYLVANIA. COMPACTFLUORESCENT BALLASTS SHALL BE ELECTRONIC ASMANUFACTURED BY ADVANCE, MAGNETEK, OR OSCRAMSYLVANIA.
28. LABEL EACH PANELBOARD, DISCONNECT SWITCH AND ENDSOF WIRING AND CABLES AS SPECIFIED.
29. VERIFY ALL DIMENSIONS BY FIELD MEASUREMENTS.
30. GIVE RIGHT-OF-WAY TO SYSTEMS REQUIRED TO BEINSTALLED AT A REQUIRED SLOPE.
31. FURNISH AND INSTALL ANY MISCELLANEOUS METAL ORWOOD SUPPORTS, FASTENERS, MOUNTS HANGERS, SIDEBRACES, ETC., WHICH MAY BE REQUIRED TO SECURELYANCHOR AND SUPPORT ELECTRICAL EQUIPMENT FURNISHEDUNDER THIS CONTRACT.
32. APPLY FIRESTOPPING TO RACEWAY PENETRATIONS OFFIRE-RATED FLOOR AND WALL ASSEMBLIES TO ACHIEVEFIRE-RESISTANCE RATING OF THE ASSEMBLY.
33. MAKE PROVISION AND PROVIDE POWER WIRING INCLUDINGFINAL EQUIPMENT CONNECTION TO ALL EQUIPMENTFURNISHED AND INSTALLED BY OTHERS. VERIFY THE EXACTREQUIREMENT OF EQUIPMENT BEFORE INSTALLATION OFELECTRICAL WORK.
34. ALL REQUIRED BUILDING PERMITS FOR THE ELECTRICALPORTION OF THE WORK SHALL BE INCLUDED. A FINALINSPECTION BY THE OWNER, ARCHITECT, ENGINEER, AND ALLINVOLVED AGENCIES WILL BE CONDUCTED UPONCOMPLETION OF THE WORK TO DETERMINE ACCEPTABILITYOF THE WORK. IN ADDITION, AN INSPECTION BY THEELECTRICAL INSPECTOR AND CERTIFICATE OF APPROVALWILL BE REQUIRED PRIOR TO FINAL PAYMENT FOR THEWORK. ALL FEES FOR BUILDING PERMITS AND ELECTRICALINSPECTIONS SHALL BE INCLUDED.
35. TESTING: ON COMPLETION OF THE WORK, THE INSTALLATIONSHALL BE FREE FROM GROUNDS AND SHORT CIRCUITS. ALLCIRCUITS SHALL BE TESTED AND LABELED. ALL MOTORCIRCUITS, CONTROL CIRCUITS, SIGNAL SYSTEMS,INTERLOCKING AND ELECTRIC HEAT CIRCUITS SHALL BETESTED FOR PROPER OPERATION.
36. GUARANTEE: THE CONTRACTOR SHALL GIVE THE OWNER AWRITTEN GUARANTEE THAT HE WILL MAKE GOOD, AT HISOWN EXPENSE, ANY DEFECTS IN MATERIALS ORWORKMANSHIP WHICH MAY DEVELOP IN ONE YEAR FROMTHE FINAL ACCEPTANCE OF THE WORK.
GENERAL ELECTRICAL NOTES17. BEFORE INSTALLING OUTLETS, THE ELECTRICAL
CONTRACTOR SHALL CONFER WITH THE ARCHITECT TODETERMINE IF THE OUTLETS ARE TO BE INSTALLED ATHEIGHTS OTHER THAN THOSE GIVEN HEREIN. IN GENERAL,UNLESS OTHERWISE NOTED ON THE DRAWINGS, ALL THEOUTLETS SHALL BE INSTALLED AT THE FOLLOWING HEIGHTFROM THE FLOOR: A.SWITCHES: 48" O.C. B. RECEPTACLE
OUTLETS: 18" O.C. C.VOICE/DATA OUTLETS: 18" O.C. D. WALLMOUNTED TELEPHONE OUTLETS: 54" O.C. RECEPTACLEOUTLETS AT COUNTERTOPS: 6" O.C. ABOVE BACKSPLASH.
18. A TYPEWRITTEN LABEL SHALL BE INSTALLED ON THE WALLPLATE OF EACH RECEPTACLE OUTLET INDICATING THECONNECTED PANEL AND CIRCUIT NUMBER.
19. ALL GROUNDING SHALL BE IN ACCORDANCE WITH THEREQUIREMENTS OF THE NEC AND AS REQUIRED BY THEDRAWINGS.
20. PANELBOARDS SHALL BE DEAD FRONT WITH RATINGS ASSCHEDULED ON DRAWINGS. PROVIDE CIRCUIT BREAKERS ASRECOMMENDED BY PANEL MANUFACTURER. PROVIDEBRANCH BREAKERS IN QUANTITIES AND RATINGS ASINDICATED ON DRAWINGS. PROVIDE TYPED DIRECTORIESREFLECTING CONNECTED LOADS.
21. BRANCH CIRCUIT BREAKERS SHALL BE OF INDIVIDUAL UNITCONSTRUCTION COMPLETE WITH QUICK-MAKE, QUICK-BREAKMECHANISM; THERMAL MAGNETIC TRIP; AMBIENTCOMPENSATION; AND SHALL BE INTERCHANGEABLE IN THEPANELBOARD ASSEMBLY IN RATINGS FROM 15 TO 100AMPERES WITHOUT NECESSITATING BUS, LINK OR ASSEMBLYREARRANGEMENT. CIRCUIT BREAKERS SHALL HAVESUITABLE SCREW TYPE LINE TERMINALS SO THAT THEY WILLBE HELD IN POSITIVE CONTACT WITH THEIR RESPECTIVELINKS OR BUSSES.
22. SAFETY SWITCHES SHALL BE HEAVY DUTY, QUICK-MAKE,QUICK-BREAK, TYPES OF THE SIZE AND FUSE AMPACITY ASNOTED ON THE DRAWINGS. PROVIDE GROUND BUS, SOLIDNEUTRAL, CLASS RK-5 DUAL ELEMENT, TIME DELAY FUSES,AND NEMA RELATED ENCLOSURE.
23. MOTOR STARTERS FOR THREE PHASE MOTORS SHALL BEFULL VOLTAGE NON-REVERSING MAGNETIC TYPES WITHPROPERLY SIZED OVERLOAD HEATERS, LONG LIFE PILOTLIGHTS, HAND-OFF-AUTO SELECTOR SWITCH, PUSHBUTTONS,AND 120V CONTROL TRANSFORMER. MANUAL MOTORSTARTERS FOR SINGLE PHASE MOTORS SHALL BE SENTINELTYPE WITH PROPERLY SIZED OVERLOAD HEATERS ANDTOGGLE TYPE DISCONNECT SWITCH MOUNTED IN A NEMARATED ENCLOSURE.
24. EACH PANELBOARD, DISCONNECT SWITCH, MOTOR STARTERAND CABINET SHALL BE IDENTIFIED BY PHENOLIC LAMINATEDPLASTIC ENGRAVED PLATES ATTACHED WITH POP RIVETS ORSHEET METAL SCREWS.
GENERAL ELECTRICAL NOTES10. ALL CONDUIT AND EQUIPMENT SHALL BE LEVEL, PLUMB, AND
PARALLEL AND PERPENDICULAR TO OTHER BUILDINGSYSTEMS AND COMPONENTS, UNLESS OTHERWISE NOTED.
11. CONDUIT AND CABLES SHALL BE INSTALLED AT LEAST 6"AWAY FROM PARALLEL RUNS OF FLUES AND HOT-WATERPIPES. LOCATE HORIZONTAL CONDUIT AND CABLE RUNSABOVE WATER PIPING.
12. PROVIDE PULL WIRES IN ALL EMPTY CONDUITS. USE NO. 14AWG ZINC-COATED STEEL OR MONOFILAMENT PLASTIC LINEWITH NOT LESS THAN 200-LB TENSILE STRENGTH. LEAVE ATLEAST 12" OF SLACK AT EACH END OF THE PULL WIRE.
13. OUTLET AND JUNCTION BOXES SHALL BE 4" SQUAREMINIMUM SIZE, GALVANIZED, STAMPED STEEL, EXCEPT ASNOTED. OUTLET BOXES SHALL BE EQUIPPED WITH PLASTERRINGS OF APPROPRIATE DEPTH TO FINISH FLUSH WITHFINISHED WALL. MULTIGANG BOXES SHALL BE OF SINGLEPIECE CONSTRUCTION WITH WALL PLATES MATCHINGRESPECTIVE DEVICE. OUTLET BOXES IN CONCRETE ORMASONRY WALLS SHALL BE MASONRY TYPE. OUTLET BOXESFOR EXPOSED EXTERIOR WALLS SHALL BE WEATHERPROOFWITH THREADED CONDUIT HUBS. JUNCTION AND PULLBOXES SHALL HAVE STEEL, SCREW-TYPE COVER PLATES.
14. WIRES AND CABLES SHALL BE COPPER CONDUCTORS ANDHAVE APPROVED INSULATION FOR THE SPACES WHERE THEYARE TO BE USED AND SHALL CONFORM TO THE LATESTREQUIREMENTS OF THE NEC. THE MINIMUM TEMPERATURERATING SHALL BE 75°C WITH TYPE THHN/THWN INSULATIONAND 600 VOLT RATING.
15. NO WIRE SMALLER THAN #12 SHALL BE USED FOR LIGHTING,RECEPTACLES, AND MOTOR CIRCUITS. ALL WIRE #10 ANDSMALLER MAY BE SOLID OR STRANDED CONDUCTOR. FORSIZE #8 AND LARGER STRANDED CABLE SHALL BE USED. ALLWIRES SHALL BE INSTALLED IN CONDUIT UNLESS OTHERWISENOTED. ALL SPLICES SHALL BE MADE WITH INSULATEDSOLDERLESS TYPE CONNECTORS. WIRING INSTALLATIONSHALL COMPLY WITH NEC 310.15(B)(3)(a). ALL FEEDER ANDBRANCH CIRCUIT CONDUCTOR AMPACITIES SHALL BEPROPERLY INCREASED FOR VOLTAGE DROP IN ACCORDANCEWITH THE NEC.
16. WIRING DEVICES SHALL BE THREE-WIRE, SPECIFICATIONGRADE, 20 AMPERE MINIMUM; DUAL VOLTAGE SWITCHES,DUPLEX RECEPTACLES, AND GROUND-FAULT CIRCUITINTERRUPTING RECEPTACLES. PROVIDE IVORY NYLON WALLPLATES FOR FINISHED AREAS. PROVIDE GASKETEDWEATHERPROOF WALL PLATES FOR EXTERIOR AREAS. WALLPLATES SHALL BE INSTALLED ON ALL SWITCHES,RECEPTACLES, VOICE/DATA OUTLETS, TV OUTLETS, ANDEMPTY BOXES. DUPLEX RECEPTACLES SHALL BE HUBBELL#5362; SINGLE POLE SWITCHES SHALL BE HUBBELL #1221;THREE-WAY SWITCHES SHALL BE HUBBELL #1223; FOUR-WAYSWITCHES SHALL BE HUBBELL #1224 OR ENGINEERAPPROVED EQUAL.
GENERAL ELECTRICAL NOTES1. SCOPE: FURNISH ALL LABOR AND MATERIALS AND INSTALL
ALL EQUIPMENT; INCLUDING, BUT NOT LIMITED TO WIRING,CONDUIT, ELECTRICAL DISTRIBUTION EQUIPMENT, LIGHTING,AND MISCELLANEOUS EQUIPMENT DETAILED ON THEDRAWINGS OR REQUIRED FOR A COMPLETE AND OPERABLEINSTALLATION.
2. ALL ELECTRICAL WORK SHALL BE COMPLIANT WITH THESTATE ADOPTED EDITION OF NFPA 70: NATIONAL ELECTRICALCODE (NEC) AND OTHER APPLICABLE STATE AND LOCALCODES.
3. COORDINATE ELECTRICAL SERVICE ENTRANCE WORK WITHMON POWER COMPANY. ELECTRICAL SERVICE WORK SHALLCOMPLY WITH MON POWER SPECIFICATIONS.
4. ALL MATERIAL SHALL BE NEW AND SHALL BE LISTED BYUNDERWRITERS LABORATORIES.
5. CONDUITS SHALL BE 1/2" MINIMUM SIZE, RIGID GALVANIZEDSTEEL, INTERMEDIATE METAL CONDUIT, LIQUID-TIGHTFLEXIBLE CONDUIT, ELECTRICAL METALLIC TUBING, FLEXIBLEMETAL CONDUIT. CONDUITS SHALL BE SIZED AND APPLIED INACCORDANCE WITH THE NEC. CONDUIT FITTINGS SHALL BEALL PLATED STEEL: SET-SCREW, THREADED ORCOMPRESSION TYPE. METAL CLAD CABLE SHALL BEPERMITTED FOR INSTALLATION.
6. ALL WIRING SHALL BE INSTALLED IN CONDUIT. BRANCHCIRCUIT WIRING SHALL BE MC CABLE AS PERMITTED BY THENEC. IN GENERAL, CONCEAL CONDUIT IN WALLS AND ABOVECEILNGS. MC CABLE SHALL BE USED WHERE OUTLETS AREINSTALLED THROUGH CONTINUOUS METAL STUD WALLS. INUNFINISHED AREAS OF THE BUILDING, CONDUIT SHALL BEEXPOSED AND ROUTED ON SURFACE OF THE CEILINGAND/OR WALLS AS HIGH AS POSSIBLE AND ROUTED SO AS TONOT INTERFERE WITH OTHER TRADES. CONDUIT ANDCABLES SHALL BE SECURED WITH APPROVED SUPPORTINGDEVICES AND RUN PARALLEL AND PERPENDICULAR TOSURROUNDING STRUCTURE.
7. CONDUITS INSTALLED UNDERGROUND SHALL BE A MINIMUMOF 18" BELOW FINISHED GRADE TO THE TOP OF THECONDUIT, UNLESS OTHERWISE NOTED. PROVIDE ROCK-FREEBACKFILL MATERIAL AND TAMP IN 8" LAYERS. PROVIDEUNDERGROUND WARNING TAPE IN TRENCH 3" BELOWFINISHED GRADE.
8. RGS CONDUIT SHALL BE USED IN ALL AREAS SUBJECTED TOPHYSICAL DAMAGE. EMT MAY BE INSTALLED ONLY INCONCEALED INTERIOR SPACES ABOVE CEILINGS OR INWALLS. OUTDOOR WIRING ABOVE GRADE SHALL BEENCLOSED IN RGS CONDUIT. OUTDOOR WIRING BELOWGRADE SHALL BE ENCLOSED IN SCHEDULE 40 PVC CONDUITUNLESS OTHERWISE NOTED.
9. CONNECT MOTORS AND EQUIPMENT SUBJECT TO VIBRATION,NOISE TRANSMISSION OR MOVEMENT WITH A MAXIMUM OF72" FLEXIBLE CONDUIT. PROVIDE LIQUID-TIGHT FLEXIBLECONDUIT IN WET OR DAMP LOCATIONS. INSTALL SEPARATEGROUND CONDUCTOR ACROSS FLEXIBLE CONNECTIONS.
RY
M CHNC
R
EGIS TERE
D
ST
V I R GI
SIONAL EN
13460
STATE OF
AI
N
WE R
EE
NIG
PROF
ES
GA Y
E
. A
UP
OS
OS
3 4
3
3
OS OS OS
OS OS
RE
F.
3
D DD
OS OSOS
33
D
InformationPamphlets
Mail
Copy/Print
AE
A
A
A
A
A
EEEE
A
FE
W
EE
XR
B B B
BBB
B
B
B
B
C
C
XAE
DE
DE
DD
D D
GG
X
DE
DE
D
D
D
D
D DD
D
R
Stairs
S2.0
Men'sRestroom
007
Women'sRestroom
009
Office
002
Office
001
MechanicalRoom
005
Corridor
000
Office
003
Storage
004
KK
K
V V
2
1
1 1
1
1 1 1
1
1
1 1
1
3 3
1
A AE
A
A
A
A AA
A A AAE
E EE
A
B
B B B
BB
AE
X XR
R
FE
EE
X
W
X
D D D
D
D D D
D
Stairs
S1.0
Kitchenette
012
Boardroom
010
2
1
1
111
1 1
E-200
1
E-200
2
KEY NOTES LIGHTING PLAN
1 CONNECT TO EXISTING BRANCH LIGHTING CIRCUIT INROOM/AREA USING #12/2 MC CABLE WITH GROUND.
CONNECT TO EXISTING EXTERIOR LIGHTING CIRCUIT OFREMOVED LIGHT FIXTURE.
CONNECT TO EXISTING EXTERIOR LIGHTING CIRCUIT USING (2) #12 CONDUCTORS AND (1) #12 EQUIPMENT GROUNDINGCONDUCTOR IN 1/2" CONDUIT.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
As indicated
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
E-200
Ground FloorLighting Plan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/4" = 1'-0"1
ENLARGED GROUND FLOOR LIGHTING PLAN - NORTH
1/4" = 1'-0"2
ENLARGED GROUND FLOOR LIGHTING PLAN - SOUTH 1/16" = 1'-0"3
GROUND FLOOR LIGHTING PLAN
GENERAL LIGHTING NOTES1. FIXTURES: SET LEVEL, PLUMB, AND SQUARE WITH CEILING
AND WALLS. SECURE ACCORDING TO MANUFACTURER'SWRITTEN INSTRUCTIONS AND APPROVED SUBMITTALMATERIALS. INSTALL LAMPS IN EACH FIXTURE.
2. CONNECT EXIT LIGHTS AND EMERGENCY BATTERY BALLASTSIN NOTED FIXTURES TO THE NEAREST UNSWITCHEDLIGHTING CIRCUIT IN THE AREA BEING SERVED.
3. EXTERIOR LIGHTING FIXTURES SHALL BE OPERATED BY ANEXISTING TIME CLOCK AND A PHOTOELECTRIC CONTROLLER.
4. PROVIDE LOW VOLTAGE WIRING FROM THE EXIT LIGHTS WITHEXTRA BATTERY CAPACITY TO THE REMOTE EMERGENCYLIGHTS INDICATED. LOW VOLTAGE WIRING SHALL BE ASRECOMMENDED BY THE EMERGENCY LIGHTING UNITMANUFACTURER.
5. SEE GENERAL ELECTRICAL NOTES ON SHEET E100 FORWIRING METHODS.
RY
M CHNC
R
EGIS TERE
D
ST
V I R GI
SIONAL EN
13460
STATE OF
AI
N
WE R
EE
NIG
PROF
ES
GA Y
E
. A
DN
3
4
DD
OS OSOS
J
J
OS
OS
3
J
J
OS
OS
OS OS
OS
E
E
FE
EE
X
DE D D
B
B B
B B
B BEB
B B
C
BB
A
A
DE DE DED DD
K
G G
DDDE
DDD
D D D
H
H
H
H
H
H
H
H
H
H
X
1
1 1 1
1
1
1
1
11
1
1
1
111
1
SharedSuite
104
SharedSuite
105
SharedSuite
106
Stairs
S2.1
Corridor
119
Kitchenette
108
Storage
110
Server
110A
Storage
111
Elevator
E1.1
Women'sRestroom
109
Men'sRestroom
107
MeetingRoom
112
PhoneRoom
102
MeetingRoom
103
Co-WorkingOpenOffice
101
A
A
H
H
H
H
H
H
H
H
H
H
B
B B
B B
B
DEX
DEDEX
D D D D
FE
EE
1
111
1
1
1 1 1
PhoneRoom
114
MeetingRoom
115
DedicatedOpenOffice
113
Corridor
119
PrivateOffice
116
PrivateOffice
117
PrivateOffice
118
Stairs
S1.1
E-201
1
E-201
2
KEY NOTES LIGHTING PLAN
1 CONNECT TO EXISTING BRANCH LIGHTING CIRCUIT INROOM/AREA USING #12/2 MC CABLE WITH GROUND.
CONNECT TO EXISTING EXTERIOR LIGHTING CIRCUIT OFREMOVED LIGHT FIXTURE.
CONNECT TO EXISTING EXTERIOR LIGHTING CIRCUIT USING (2) #12 CONDUCTORS AND (1) #12 EQUIPMENT GROUNDINGCONDUCTOR IN 1/2" CONDUIT.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
As indicated
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
E-201
First Floor LightingPlan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/4" = 1'-0"1
ENLARGED FIRST FLOOR LIGHTING PLAN - NORTH
1/4" = 1'-0"2
ENLARGED FIRST FLOOR LIGHTING PLAN - SOUTH 1/16" = 1'-0"
3FIRST FLOOR POWER PLAN
GENERAL LIGHTING NOTES1. FIXTURES: SET LEVEL, PLUMB, AND SQUARE WITH CEILING
AND WALLS. SECURE ACCORDING TO MANUFACTURER'SWRITTEN INSTRUCTIONS AND APPROVED SUBMITTALMATERIALS. INSTALL LAMPS IN EACH FIXTURE.
2. CONNECT EXIT LIGHTS AND EMERGENCY BATTERY BALLASTSIN NOTED FIXTURES TO THE NEAREST UNSWITCHEDLIGHTING CIRCUIT IN THE AREA BEING SERVED.
3. EXTERIOR LIGHTING FIXTURES SHALL BE OPERATED BY ANEXISTING TIME CLOCK AND A PHOTOELECTRIC CONTROLLER.
4. PROVIDE LOW VOLTAGE WIRING FROM THE EXIT LIGHTS WITHEXTRA BATTERY CAPACITY TO THE REMOTE EMERGENCYLIGHTS INDICATED. LOW VOLTAGE WIRING SHALL BE ASRECOMMENDED BY THE EMERGENCY LIGHTING UNITMANUFACTURER.
5. SEE GENERAL ELECTRICAL NOTES ON SHEET E100 FORWIRING METHODS.
RY
M CHNC
R
EGIS TERE
D
ST
V I R GI
SIONAL EN
13460
STATE OF
AI
N
WE R
EE
NIG
PROF
ES
GA Y
E
. A
OS OS
3
3
4
D
DDJ J J
OS OS OS
OS OS OS
3
JJJ
OS OS OS
OS OS OS
BeverageCenter
WW
E
FE
EE
XDE D DED D D D DEDE
H
H H H
H
H
HH
H
H
H
H
B
B
B
B
B
B
X
G G
D D DE
D
D
D
D
D
D
BB
DE
DE
D
DDD
D
D
K
Stairs
S2.2
Storage
210
Women'sRestroom
209
Men'sRestroom
207
MeetingRoom
211
PrivateOffice
201
PrivateOffice
205
PrivateOffice
203
PrivateOffice
202
PrivateOffice
204
PrivateOffice
206
Elevator
E1.2
Lounge
208
Corridor
200
1
1 1 1
1
1 1 1
1 1
1
1
1
2 2
Stairs
S1.2Chamberof
CommercePrivateOffice
213
Chamberof
CommercePrivateOffice
217
Chamberof
CommercePrivateOffice
215
Chamberof
CommercePrivateOffice
212
Chamberof
CommercePrivateOffice
214
Chamberof
CommercePrivateOffice
216
B
B
B
B
B
B
DEDE DDD D
H
H
H
H
H
H
H
H
H
H
H
H
FE
EE
X
1 1 1
1 1 1
1
E-202
1
E-202
2
KEY NOTES LIGHTING PLAN
1 CONNECT TO EXISTING BRANCH LIGHTING CIRCUIT INROOM/AREA USING #12/2 MC CABLE WITH GROUND.
CONNECT TO EXISTING EXTERIOR LIGHTING CIRCUIT OFREMOVED LIGHT FIXTURE.
CONNECT TO EXISTING EXTERIOR LIGHTING CIRCUIT USING (2) #12 CONDUCTORS AND (1) #12 EQUIPMENT GROUNDINGCONDUCTOR IN 1/2" CONDUIT.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
As indicated
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
E-202
Second FloorLighting Plan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/4" = 1'-0"1
ENLARGED SECOND FLOOR LIGHTING PLAN - NORTH
1/4" = 1'-0"2
ENLARGED SECOND FLOOR LIGHTING PLAN - SOUTH 1/16" = 1'-0"3
SECOND FLOOR LIGHTING PLAN
GENERAL LIGHTING NOTES1. FIXTURES: SET LEVEL, PLUMB, AND SQUARE WITH CEILING
AND WALLS. SECURE ACCORDING TO MANUFACTURER'SWRITTEN INSTRUCTIONS AND APPROVED SUBMITTALMATERIALS. INSTALL LAMPS IN EACH FIXTURE.
2. CONNECT EXIT LIGHTS AND EMERGENCY BATTERY BALLASTSIN NOTED FIXTURES TO THE NEAREST UNSWITCHEDLIGHTING CIRCUIT IN THE AREA BEING SERVED.
3. EXTERIOR LIGHTING FIXTURES SHALL BE OPERATED BY ANEXISTING TIME CLOCK AND A PHOTOELECTRIC CONTROLLER.
4. PROVIDE LOW VOLTAGE WIRING FROM THE EXIT LIGHTS WITHEXTRA BATTERY CAPACITY TO THE REMOTE EMERGENCYLIGHTS INDICATED. LOW VOLTAGE WIRING SHALL BE ASRECOMMENDED BY THE EMERGENCY LIGHTING UNITMANUFACTURER.
5. SEE GENERAL ELECTRICAL NOTES ON SHEET E100 FORWIRING METHODS.
RY
M CHNC
R
EGIS TERE
D
ST
V I R GI
SIONAL EN
13460
STATE OF
AI
N
WE R
EE
NIG
PROF
ES
GA Y
E
. A
UP
W
F
S
GC GC GC
W
GC
F S
J J
TV
JJ
S
H
S H
S
MS
GC
GC
W
FS
J J
TV TV
W
J J
FF
GC
InformationPamphlets
Mail
Copy/Print
E
E E E E E E
E
E
E
E
E E E
E
E E
E
CT
E
AGC AGC
Stairs
S2.0
Men'sRestroom
007
Women'sRestroom
009
Office
002
Office
001
MechanicalRoom
005
Corridor
000
Office
003
Storage
004
E E
C C C
AGCAGC
FA
CP
WC
E
ELEV
CB
A ABE A
FIRE ALARMDISCONNECT
2
2 2
DATA DATA
2 2
1
1 AA
AA2
WH
B1P1 P2
B2
4
44
1
1
1
2
2
1
1
E E E EE E E
EE
E
E E EEE EE E
E
E E E E E EEE E
60"AFF
60"AFF
60"
F F
Stairs
S1.0
Kitchenette
012
Boardroom
010
AGC AGC
AGC AGC
E E
TV
1" COMM
3/4" POWER
TV
1" COMM
3/4" POWER
DATADATA
33
1
3
3
3
3
3
3
WH1
E-300
1
E-300
2
KEY NOTES POWER PLAN
1 CONNECT TO EXISTING BRANCH CIRCUIT TO DEVICES SHOWNUSING #12/2 MC CABLE WITH GROUND.
CONNECT TO EXISTING SPARE 20A, 1-POLE BREAKER INPANEL AA USING #12/2 MC CABLE WITH GROUND.
CONNECT TO EXISTING SPARE 20A, 1-POLE BREAKER INPANEL AB USING #12/2 MC CABLE WITH GROUND.
CONNECT TO EXISTING BRANCH CIRCUIT WIRING FROMREMOVED EQUIPMENT.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
1/8" = 1'-0"
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\Ele
ctr
ical -
Deta
ils -
2014.r
vt
E-801
Diagrams & Details
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
Not to Scale2
Voice/Data Outlet Detail
COMMUNICATIONS NOTES1. VOICE/DATA CABLING: PROVIDE (1) 4 PAIR, 24
AWG, UTP, CAT.5e, CMP RATED CABLE WITHBLUE JACKET FROM EACH OUTLET BOXINDICATED TO A PATCH PANEL LOCATED INTELECOM ROOM ON RESPECTIVE FLOOR.CABLES SHALL BE INSTALLED IN 3/4" EMT MIN.WHERE CONCEALED WITHIN WALLS, ABOVEINACCESSIBLE CEILINGS, AND EXPOSEDCEILING AREAS. PROVIDE (1) RJ-45 JACK IN ASINGLE WALL PLATE FOR EACH OUTLETSHOWN. TERMINATE EACH CAT. 5e CABLE TORJ-45 JACK AND PATCH PANEL. PROPERLYLABEL EACH END OF CABLE.
2. PATCH PANEL: PROVIDE A 19-INCH WALLMOUNTED RACK IN EACH ELECTRICALCLOSET. COORDINATE LOCATION OF RACKWITH OWNER. PROVIDE CAT. 5e PATCHPANEL WITH PORTS FOR CONNECTINGOUTLETS SHOWN PLUS 25% ADDITIONALCAPACITY FOR FUTURE OUTLETS.
3. TELEVISION CABLING: WHERE TV FACILITIESARE INDICATED, PROVIDE (1) RG6/U SOLIDCOPPER QUAD SHIELD COAXIAL,PLENUM-RATED CABLE FROM EACH OUTLETBOX INDICATED TO MECHANICAL ROOM 005.CABLES SHALL BE INSTALLED IN 3/4" EMT MIN.WHERE CONCEALED WITHIN WALLS, ABOVEINACCESSIBLE CEILINGS, AND EXPOSEDCEILING AREAS. PROVIDE A 75 OHM, F-TYPECONNECTOR IN A SINGLE WALL PLATE FOREACH OUTLET SHOWN. PROVIDE ALL CABLETERMINATIONS. PROPERLY LABEL EACH ENDOF CABLE. PROVIDE TV DISTRIBUTIONEQUIPMENT; INCLUDING BUT NOT LIMITED TO,DISTRIBUTION AMPLIFIERS, DIRECTIONALMULTI-TAPS, AND SPLITTERS.
4. CABLE INSTALLATION: CABLES SHALL BEENCLOSED IN RACEWAY WHERE INSTALLEDWITHIN FINISHED WALLS AND ABOVEINACCESSIBLE CEILINGS AREAS. PROVIDEJ-HOOKS, SECURED TO THE BUILDINGSTRUCTURE AT 4'-0" MAXIMUM INTERVALS, TOSUPPORT CABLES ABOVE ACCESSIBLECEILINGS.
5. IDENTIFICATION: LABEL EACH END OF ALLCABLE RUNS.
FIRE ALARM SYSTEM NOTES14. PROVIDE A TEST KEY SWITCH IN THE ELEVATOR MACHINE
ROOM TO SIMULATE THE ACTIVATION OF A HEAT DETECTORTO TEST THE POWER SHUT DOWN OPERATION OF THEELEVATOR.
15. WHEN ACTIVATED, THE SMOKE DETECTORS IN THEELEVATOR SHAFT, THE ELEVATOR LOBBIES, AND IN THEELEVATOR MACHINE ROOM SHALL SOUND A GENERAL FIREALARM AND RECALL THE ELEVATOR TO THE LEVEL OF THEEXIT DISCHARGE.
16. PROVIDE DUCT-TYPE SMOKE DETECTORS IN THE RETURN AIRDUCT OF THE HVAC UNITS INDICATED. WHEN ACTIVATED, THEDUCT-TYPE SMOKE DETECTORS SHALL AUTOMATICALLYSHUT DOWN THE HVAC UNIT, CLOSE THE MAIN FAN DAMPERS,AND SOUND A GENERAL FIRE ALARM.
17. PROVIDE WIRING AND CONNECTION TO ALL FLOW, TAMPER,AND PIV TAMPER SWITCHES. COORDINATE LOCATION WITHTHE SPRINKLER CONTRACTOR. EACH FLOW SWITCH SHALLBE ANNUNCIATED SEPARATELY. TAMPER AND PIV TAMPERSWITCHES SHALL BE ELECTRICALLY-SUPERVISED ANDANNUNCIATED AS A TROUBLE ON THE FACP.
18. PROVIDE REMOTE ALARM INDICATOR AND TEST STATION FOREACH DUCT-TYPE SMOKE DETECTOR AND SPRINKLERSYSTEM FLOW SWITCH. MOUNT STATION IN RECESSEDDEVICE BOX LOCATED 6'-0'' ABOVE FINISHED FLOOR. WIRINGSHALL BE ENCLOSED WITHIN RACEWAY AND CONCEALEDWITHIN WALL.
19. ALL EXTINGUISHING SYSTEMS SHALL BE CONNECTED TO THEFIRE ALARM SYSTEM PER CODE.
20. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION.
21. IDENTIFY SYSTEM COMPONENTS, WIRING, CABLING, ANDTERMINALS ACCORDING TO DIVISION 28 SPECIFICATIONS.
22. FIRE ALARM WIRING SHALL BE ENCLOSED IN METALRACEWAY SEPARATE FROM OTHER DATA AND POWERWIRING WHERE CONCEALED WITHIN WALLS AND EXPOSEDON WALLS OF UNFINISHED SPACES OR UNLESS OTHERWISEINDICATED. PLENUM-RATED FIRE ALARM CABLE SHALL BEPERMITTED WHERE CONCEALED ABOVE GRID CEILINGS INFINISHED AREAS. SECURE CABLES TO BUILDING STRUCTUREUSING APPROVED SUPPORTING DEVICES MOUNTED AT 4'-0"MAXIMUM INTERVALS. BOXES SHALL BE PAINTED RED FORIDENTIFICATION.
FIRE ALARM SYSTEM NOTES1. ALL WORK SHALL COMPLY WITH THE WEST VIRGINIA STATE
FIRE CODE. ALL WORK SHALL COMPLY WITH THE NFPA CODEADOPTED BY THE WEST VIRGINIA STATE FIRE CODE.
2. THE FIRE ALARM INSTALLER SHALL SUBMIT REQUIREDINFORMATION TO THE WEST VIRGINIA STATE FIRE MARSHALFOR APPROVAL. THE FIRE ALARM INSTALLER SHALL SUBMITFIRE ALARM DRAWINGS, COMPLETE WITH EQUIPMENTLOCATIONS, DIMENSIONS BETWEEN LIKE DEVICES TO VERIFYPROPER SPACING, AND FIRE ALARM RISER DIAGRAM
3. REPLACE THE EXISTING NONCODED, ZONED FIRE ALARMSYSTEM WITH A NEW ADDRESSABLE FIRE ALARM SYSTEMWITH MANUAL AND AUTOMATIC ALARM INITIATION; ANDHARDWIRED FOR SIGNAL TRANSMISSION DEDICATED TO FIREALARM SERVICE ONLY, USING A UNIQUE ADDRESS FOR EACHALARM INITIATION DEVICE.
4. PROVIDE A DEDICATED 20 AMP, 120 VOLT BRANCH CIRCUITFOR FACP POWER.
5. PROVIDE A DEDICATED TELEPHONE LINE TO FACP FORTRANSMITTING MEANS TO REMOTE SUPERVISING STATIONFROM DIGITAL ALARM COMMUNICATOR TRANSMITTER.
6. PROVIDE A FIRE ALARM ANNUNCIATOR PANEL IN MAINVESTIBULE.
7. SMOKE DETECTORS SHALL BE PLACED A MAXIMUM OF 15FEET FROM THE ENDS OF CORRIDORS OR WALLS AND 30FEET ON CENTER AND IN ROOMS OPEN TO THE CORRIDORS.EXCEEDING THE SPACING REQUIREMENTS WILL REQUIRESUBMISSION OF TECHNICAL DATA FOR APPROVAL BY THEFIRE MARSHAL.
8. IN CORRIDORS, VISIBLE NOTIFICATION APPLIANCES SHALL BELOCATED NOT MORE THAN 15 FEET FROM THE END OF THECORRIDOR WITH A SEPARATION NOT GREATER THAN 100FEET BETWEEN APPLIANCES.
9. VISIBLE NOTIFICATION APPLIANCES SHALL BE LOCATED INALL PUBLIC TOILETS.
10. PULL STATIONS SHALL BE LOCATED NO GREATER THAN 200FEET FROM EACH OTHER AND AT ALL EXITS.
11. WHERE EXISTING DEVICE BOXES ARE BEING USED FOR NEWCONSTRUCTION, VERIFY PROPER MOUNTING HEIGHT. IFMOUNTING HEIGHT OF PROPOSED DEVICE IS NOT PER CODE,REPLACE CONCEALED BOX AND RACEWAY AT PROPERHEIGHT.
12. PROVIDE ELEVATOR EMERGENCY OPERATION PER CURRENTEDITION OF ASME A17.1.
13. HEAT DETECTORS IN THE ELEVATOR SHAFT AND IN THEELEVATOR MACHINE ROOM SHALL BE MOUNTED WITHIN 2FEET OF EACH SPRINKLER HEAD. SPRINKLER HEAD SHALLHAVE A HIGHER RESPONSE TIME INDEX (RTI) THAN THE HEATDETECTOR. WHEN ACTIVATED, THE HEAT DETECTORS IN THEELEVATOR SHAFT AND IN THE ELEVATOR MACHINE ROOMSHALL SOUND A GENERAL FIRE ALARM, RECALL THEELEVATOR TO THE LEVEL OF EXIT DISCHARGE ANDAUTOMATICALLY SHUT DOWN POWER TO THE ELEVATORUSING A SHUNT-TRIP CIRCUIT BREAKER.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
As indicated
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
ED-100
Ground FloorElectrical DemolitionPlan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/4" = 1'-0"2
ENLARGED GROUND FLOOR ELECTRICAL DEMOLITION PLAN -SOUTH
1/4" = 1'-0"3
ENLARGED GROUND FLOOR ELECTRICAL DEMOLITION PLAN -NORTH
1/16" = 1'-0"1
DEMO - GROUND FLOOR ELECTRICAL PLAN
GENERAL DEMOLITION NOTES1. ALL DEVICES AND EQUIPMENT SHOWN ON THE ELECTRICAL
DEMOLITION PLAN ARE FOR REFERENCE ONLY AND SHALL BEFIELD VERIFIED BEFORE STARTING WORK. NOTIFY A/E IFDEVICES AND EQUIPMENT NOT SHOWN ON THE PLAN AREFOUND DURING DEMOLITION WORK.
2. REMOVE EXISTING BRANCH CIRCUIT WIRING FROM FIXTURESAND DEVICES BEING REMOVED BACK TO SOURCE CIRCUITBREAKER. VERIFY POWER CONTINUATION OF EXISTINGFIXTURES AND DEVICES INDICATED TO REMAIN.
3. REMOVE EXISTING LIGHT FIXTURES, EXIT LIGHTS, ANDEMERGENCY BATTERY LIGHTS WITHIN THE AREA OFCONSTRUCTION, UNLESS OTHERWISE NOTED.
4. REMOVE EXISTING LIGHT SWITCHES, WALL PLATES, ANDASSOCIATED WIRING WITHIN THE AREA OF CONSTRUCTION,UNLESS OTHERWISE NOTED.
5. EXISTING LIGHT SWITCHES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECT LIGHTSWITCH TO EXISTING WIRING AS INDICATED. REPLACE WALLPLATE TO MATCH.
6. EXISTING RECESSED DEVICE BOXES FOR NOTED LIGHTSWITCHES AND RECEPTACLES AND ASSOCIATED CONCEALEDRACEWAY SHALL REMAIN FOR USE WITH NEWCONSTRUCTION.
7. PROVIDE A BLANK WALL PLATE FOR ALL EXISTING RECESSEDDEVICE BOXES NOT USED FOR NEW CONSTRUCTION.PROVIDE GANGING OF WALL PLATE AS REQUIRED TO COVEREXISTING DEVICE BOX.
8. REMOVE EXISTING RECEPTACLES AS INDICATED. REMOVEASSOCIATED BRANCH CIRCUIT WIRING BACK TO SOURCECIRCUIT BREAKER. VERIFY POWER CONTINUATION OFEXISTING RECEPTACLES INDICATED TO REMAIN.
9. EXISTING RECEPTACLES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECTRECEPTACLE TO EXISTING WIRING AS INDICATED. REPLACEWALL PLATE TO MATCH.
10. REMOVE EXISTING VOICE/DATA OUTLETS AS INDICATED.REMOVE VOICE/DATA CABLES BACK TO PATCH PANEL.EXISTING RECESSED BOXES AND CONCEALED RACEWAYSHALL REMAIN FOR FUTURE USE. PROVIDE BLANK WALLPLATES TO COVER EXISTING DEVICE BOXES.
11. REPLACE EXISTING BLANK WALL PLATES WITH WALL PLATESMATCHING PLATES OF DEVICES USED IN NEWCONSTRUCTION.
12. REMOVE EXISTING EXPOSED CONDUIT AND SURFACERACEWAY ON FINISHED WALLS, UNLESS USED FOR NEWCONSTRUCTION.
13. REMOVE EXISTING ACCESS CONTROL SYSTEM DEVICES ANDASSOCIATED WIRING.
14. SEAL FIRE RATED WALLS, FLOORS AND STRUCTURAL CEILINGFROM REMOVED RACEWAY AND SLEEVES MATCHING FIRERATING OF EXISTING ASSEMBLY.
15. REMOVE ALL EXISTING ACCESSIBLE POWER WIRING, DATACABLES, AND ASSOCIATED RACEWAYS NOT BEING USED FORNEW CONSTRUCTION.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
16. REMOVE EXISTING SURFACE MOUNTED RECEPTACLES ANDASSOCIATED SURFACE RACEWAY. VERIFY POWERCONTINUATION AND TERMINATE BRANCH CIRCUIT WIRING INNEAREST ACCESSIBLE JUNCTION BOX. REMOVE EXISTINGBRANCH CIRCUIT WIRING BACK TO SOURCE CIRCUITBREAKER FOR DEDICATED RECEPTACLES.
17. REMOVE EXISTING SURFACE MOUNTED VOICE/DATA OUTLETSAND ASSOCIATED SURFACE RACEWAY. REMOVE VOICE/DATACABLES BACK TO PATCH PANEL.
18. REMOVE EXISTING FIRE ALARM SYSTEM AND ASSOCIATEDCABLING. EXISTING RECESSED DEVICE BOXES ANDCONCEALED RACEWAY SHALL REMAIN AND BE USED FORNEW CONSTRUCTION IF MOUNTING HEIGHT IS PER NFPAGUIDELINES. EXISTING FIRE ALARM SYSTEM SHALL REMAININ OPERATION UNTIL NEW SYSTEM IS INSTALLED.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
As indicated
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
ED-101
First Floor ElectricalDemolition Plan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/16" = 1'-0"1
DEMO - FIRST FLOOR ELECTRICAL PLAN
1/4" = 1'-0"2
ENLARGED FIRST FLOOR ELECTRICAL DEMOLITION PLAN - NORTH
1/4" = 1'-0"3
ENLARGED FIRST FLOOR ELECTRICAL DEMOLITION PLAN - SOUTH
GENERAL DEMOLITION NOTES1. ALL DEVICES AND EQUIPMENT SHOWN ON THE ELECTRICAL
DEMOLITION PLAN ARE FOR REFERENCE ONLY AND SHALL BEFIELD VERIFIED BEFORE STARTING WORK. NOTIFY A/E IFDEVICES AND EQUIPMENT NOT SHOWN ON THE PLAN AREFOUND DURING DEMOLITION WORK.
2. REMOVE EXISTING BRANCH CIRCUIT WIRING FROM FIXTURESAND DEVICES BEING REMOVED BACK TO SOURCE CIRCUITBREAKER. VERIFY POWER CONTINUATION OF EXISTINGFIXTURES AND DEVICES INDICATED TO REMAIN.
3. REMOVE EXISTING LIGHT FIXTURES, EXIT LIGHTS, ANDEMERGENCY BATTERY LIGHTS WITHIN THE AREA OFCONSTRUCTION, UNLESS OTHERWISE NOTED.
4. REMOVE EXISTING LIGHT SWITCHES, WALL PLATES, ANDASSOCIATED WIRING WITHIN THE AREA OF CONSTRUCTION,UNLESS OTHERWISE NOTED.
5. EXISTING LIGHT SWITCHES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECT LIGHTSWITCH TO EXISTING WIRING AS INDICATED. REPLACE WALLPLATE TO MATCH.
6. EXISTING RECESSED DEVICE BOXES FOR NOTED LIGHTSWITCHES AND RECEPTACLES AND ASSOCIATED CONCEALEDRACEWAY SHALL REMAIN FOR USE WITH NEWCONSTRUCTION.
7. PROVIDE A BLANK WALL PLATE FOR ALL EXISTING RECESSEDDEVICE BOXES NOT USED FOR NEW CONSTRUCTION.PROVIDE GANGING OF WALL PLATE AS REQUIRED TO COVEREXISTING DEVICE BOX.
8. REMOVE EXISTING RECEPTACLES AS INDICATED. REMOVEASSOCIATED BRANCH CIRCUIT WIRING BACK TO SOURCECIRCUIT BREAKER. VERIFY POWER CONTINUATION OFEXISTING RECEPTACLES INDICATED TO REMAIN.
9. EXISTING RECEPTACLES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECTRECEPTACLE TO EXISTING WIRING AS INDICATED. REPLACEWALL PLATE TO MATCH.
10. REMOVE EXISTING VOICE/DATA OUTLETS AS INDICATED.REMOVE VOICE/DATA CABLES BACK TO PATCH PANEL.EXISTING RECESSED BOXES AND CONCEALED RACEWAYSHALL REMAIN FOR FUTURE USE. PROVIDE BLANK WALLPLATES TO COVER EXISTING DEVICE BOXES.
11. REPLACE EXISTING BLANK WALL PLATES WITH WALL PLATESMATCHING PLATES OF DEVICES USED IN NEWCONSTRUCTION.
12. REMOVE EXISTING EXPOSED CONDUIT AND SURFACERACEWAY ON FINISHED WALLS, UNLESS USED FOR NEWCONSTRUCTION.
13. REMOVE EXISTING ACCESS CONTROL SYSTEM DEVICES ANDASSOCIATED WIRING.
14. SEAL FIRE RATED WALLS, FLOORS AND STRUCTURAL CEILINGFROM REMOVED RACEWAY AND SLEEVES MATCHING FIRERATING OF EXISTING ASSEMBLY.
15. REMOVE ALL EXISTING ACCESSIBLE POWER WIRING, DATACABLES, AND ASSOCIATED RACEWAYS NOT BEING USED FORNEW CONSTRUCTION.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
16. REMOVE EXISTING SURFACE MOUNTED RECEPTACLES ANDASSOCIATED SURFACE RACEWAY. VERIFY POWERCONTINUATION AND TERMINATE BRANCH CIRCUIT WIRING INNEAREST ACCESSIBLE JUNCTION BOX. REMOVE EXISTINGBRANCH CIRCUIT WIRING BACK TO SOURCE CIRCUITBREAKER FOR DEDICATED RECEPTACLES.
17. REMOVE EXISTING SURFACE MOUNTED VOICE/DATA OUTLETSAND ASSOCIATED SURFACE RACEWAY. REMOVE VOICE/DATACABLES BACK TO PATCH PANEL.
18. REMOVE EXISTING FIRE ALARM SYSTEM AND ASSOCIATEDCABLING. EXISTING RECESSED DEVICE BOXES ANDCONCEALED RACEWAY SHALL REMAIN AND BE USED FORNEW CONSTRUCTION IF MOUNTING HEIGHT IS PER NFPAGUIDELINES. EXISTING FIRE ALARM SYSTEM SHALL REMAININ OPERATION UNTIL NEW SYSTEM IS INSTALLED.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
As indicated
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
ED-102
Second FloorElectrical DemolitionPlan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/16" = 1'-0"1
DEMO - SECOND FLOOR ELECTRICAL PLAN
1/4" = 1'-0"2
ENLARGED SECOND FLOOR ELECTRICAL DEMOLITION PLAN -NORTH
1/4" = 1'-0"3
ENLARGED SECOND FLOOR ELECTRICAL DEMOLITION PLAN -SOUTH
GENERAL DEMOLITION NOTES1. ALL DEVICES AND EQUIPMENT SHOWN ON THE ELECTRICAL
DEMOLITION PLAN ARE FOR REFERENCE ONLY AND SHALL BEFIELD VERIFIED BEFORE STARTING WORK. NOTIFY A/E IFDEVICES AND EQUIPMENT NOT SHOWN ON THE PLAN AREFOUND DURING DEMOLITION WORK.
2. REMOVE EXISTING BRANCH CIRCUIT WIRING FROM FIXTURESAND DEVICES BEING REMOVED BACK TO SOURCE CIRCUITBREAKER. VERIFY POWER CONTINUATION OF EXISTINGFIXTURES AND DEVICES INDICATED TO REMAIN.
3. REMOVE EXISTING LIGHT FIXTURES, EXIT LIGHTS, ANDEMERGENCY BATTERY LIGHTS WITHIN THE AREA OFCONSTRUCTION, UNLESS OTHERWISE NOTED.
4. REMOVE EXISTING LIGHT SWITCHES, WALL PLATES, ANDASSOCIATED WIRING WITHIN THE AREA OF CONSTRUCTION,UNLESS OTHERWISE NOTED.
5. EXISTING LIGHT SWITCHES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECT LIGHTSWITCH TO EXISTING WIRING AS INDICATED. REPLACE WALLPLATE TO MATCH.
6. EXISTING RECESSED DEVICE BOXES FOR NOTED LIGHTSWITCHES AND RECEPTACLES AND ASSOCIATED CONCEALEDRACEWAY SHALL REMAIN FOR USE WITH NEWCONSTRUCTION.
7. PROVIDE A BLANK WALL PLATE FOR ALL EXISTING RECESSEDDEVICE BOXES NOT USED FOR NEW CONSTRUCTION.PROVIDE GANGING OF WALL PLATE AS REQUIRED TO COVEREXISTING DEVICE BOX.
8. REMOVE EXISTING RECEPTACLES AS INDICATED. REMOVEASSOCIATED BRANCH CIRCUIT WIRING BACK TO SOURCECIRCUIT BREAKER. VERIFY POWER CONTINUATION OFEXISTING RECEPTACLES INDICATED TO REMAIN.
9. EXISTING RECEPTACLES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECTRECEPTACLE TO EXISTING WIRING AS INDICATED. REPLACEWALL PLATE TO MATCH.
10. REMOVE EXISTING VOICE/DATA OUTLETS AS INDICATED.REMOVE VOICE/DATA CABLES BACK TO PATCH PANEL.EXISTING RECESSED BOXES AND CONCEALED RACEWAYSHALL REMAIN FOR FUTURE USE. PROVIDE BLANK WALLPLATES TO COVER EXISTING DEVICE BOXES.
11. REPLACE EXISTING BLANK WALL PLATES WITH WALL PLATESMATCHING PLATES OF DEVICES USED IN NEWCONSTRUCTION.
12. REMOVE EXISTING EXPOSED CONDUIT AND SURFACERACEWAY ON FINISHED WALLS, UNLESS USED FOR NEWCONSTRUCTION.
13. REMOVE EXISTING ACCESS CONTROL SYSTEM DEVICES ANDASSOCIATED WIRING.
14. SEAL FIRE RATED WALLS, FLOORS AND STRUCTURAL CEILINGFROM REMOVED RACEWAY AND SLEEVES MATCHING FIRERATING OF EXISTING ASSEMBLY.
15. REMOVE ALL EXISTING ACCESSIBLE POWER WIRING, DATACABLES, AND ASSOCIATED RACEWAYS NOT BEING USED FORNEW CONSTRUCTION.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
16. REMOVE EXISTING SURFACE MOUNTED RECEPTACLES ANDASSOCIATED SURFACE RACEWAY. VERIFY POWERCONTINUATION AND TERMINATE BRANCH CIRCUIT WIRING INNEAREST ACCESSIBLE JUNCTION BOX. REMOVE EXISTINGBRANCH CIRCUIT WIRING BACK TO SOURCE CIRCUITBREAKER FOR DEDICATED RECEPTACLES.
17. REMOVE EXISTING SURFACE MOUNTED VOICE/DATA OUTLETSAND ASSOCIATED SURFACE RACEWAY. REMOVE VOICE/DATACABLES BACK TO PATCH PANEL.
18. REMOVE EXISTING FIRE ALARM SYSTEM AND ASSOCIATEDCABLING. EXISTING RECESSED DEVICE BOXES ANDCONCEALED RACEWAY SHALL REMAIN AND BE USED FORNEW CONSTRUCTION IF MOUNTING HEIGHT IS PER NFPAGUIDELINES. EXISTING FIRE ALARM SYSTEM SHALL REMAININ OPERATION UNTIL NEW SYSTEM IS INSTALLED.
O N E D O U G H B O Y S Q U A R E3 4 0 0 B U T L E R S T R E E T
P I T T S B U R G H, P A 1 5 2 0 1T E L : 4 1 2. 6 8 3. 3 2 3 0F A X : 4 1 2. 6 8 3. 3 5 6 3w w w . d e s m o n e . c o m
1/8" = 1'-0"
Z:\
ME
P C
UR
RE
NT
PR
OJE
CT
S\D
esm
on
e A
rch
itects
- J
ob
s\D
ES
MO
NE
-ME
P15-0
3 -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter-
Ph
ase II\R
evit
& C
AD
\E -
Mo
rgan
tow
n E
nte
rpri
se C
en
ter
Off
ice.r
vt
ED-103
Roof DemolitionPlan
Monongalia County DevelopmentAuthority
Morg
anto
wn E
nte
rprise C
ente
r O
ffic
e B
uild
ing
3942
08.26.2015
955 H
art
man
Ru
n R
oad
Mo
rgan
tow
n, W
V 2
6505
Inte
rio
r &
Exte
rio
r R
en
ovati
on
s
08.2
6.2
015
1/8" = 1'-0"1
DEMO - Roof Floor Power Plan
GENERAL DEMOLITION NOTES1. ALL DEVICES AND EQUIPMENT SHOWN ON THE ELECTRICAL
DEMOLITION PLAN ARE FOR REFERENCE ONLY AND SHALL BEFIELD VERIFIED BEFORE STARTING WORK. NOTIFY A/E IFDEVICES AND EQUIPMENT NOT SHOWN ON THE PLAN AREFOUND DURING DEMOLITION WORK.
2. REMOVE EXISTING BRANCH CIRCUIT WIRING FROM FIXTURESAND DEVICES BEING REMOVED BACK TO SOURCE CIRCUITBREAKER. VERIFY POWER CONTINUATION OF EXISTINGFIXTURES AND DEVICES INDICATED TO REMAIN.
3. REMOVE EXISTING LIGHT FIXTURES, EXIT LIGHTS, ANDEMERGENCY BATTERY LIGHTS WITHIN THE AREA OFCONSTRUCTION, UNLESS OTHERWISE NOTED.
4. REMOVE EXISTING LIGHT SWITCHES, WALL PLATES, ANDASSOCIATED WIRING WITHIN THE AREA OF CONSTRUCTION,UNLESS OTHERWISE NOTED.
5. EXISTING LIGHT SWITCHES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECT LIGHTSWITCH TO EXISTING WIRING AS INDICATED. REPLACE WALLPLATE TO MATCH.
6. EXISTING RECESSED DEVICE BOXES FOR NOTED LIGHTSWITCHES AND RECEPTACLES AND ASSOCIATED CONCEALEDRACEWAY SHALL REMAIN FOR USE WITH NEWCONSTRUCTION.
7. PROVIDE A BLANK WALL PLATE FOR ALL EXISTING RECESSEDDEVICE BOXES NOT USED FOR NEW CONSTRUCTION.PROVIDE GANGING OF WALL PLATE AS REQUIRED TO COVEREXISTING DEVICE BOX.
8. REMOVE EXISTING RECEPTACLES AS INDICATED. REMOVEASSOCIATED BRANCH CIRCUIT WIRING BACK TO SOURCECIRCUIT BREAKER. VERIFY POWER CONTINUATION OFEXISTING RECEPTACLES INDICATED TO REMAIN.
9. EXISTING RECEPTACLES INDICATED TO REMAIN SHALL BEREPLACED TO MATCH NEW CONSTRUCTION. CONNECTRECEPTACLE TO EXISTING WIRING AS INDICATED. REPLACEWALL PLATE TO MATCH.
10. REMOVE EXISTING VOICE/DATA OUTLETS AS INDICATED.REMOVE VOICE/DATA CABLES BACK TO PATCH PANEL.EXISTING RECESSED BOXES AND CONCEALED RACEWAYSHALL REMAIN FOR FUTURE USE. PROVIDE BLANK WALLPLATES TO COVER EXISTING DEVICE BOXES.
11. REPLACE EXISTING BLANK WALL PLATES WITH WALL PLATESMATCHING PLATES OF DEVICES USED IN NEWCONSTRUCTION.
12. REMOVE EXISTING EXPOSED CONDUIT AND SURFACERACEWAY ON FINISHED WALLS, UNLESS USED FOR NEWCONSTRUCTION.
13. REMOVE EXISTING ACCESS CONTROL SYSTEM DEVICES ANDASSOCIATED WIRING.
14. SEAL FIRE RATED WALLS, FLOORS AND STRUCTURAL CEILINGFROM REMOVED RACEWAY AND SLEEVES MATCHING FIRERATING OF EXISTING ASSEMBLY.
15. REMOVE ALL EXISTING ACCESSIBLE POWER WIRING, DATACABLES, AND ASSOCIATED RACEWAYS NOT BEING USED FORNEW CONSTRUCTION.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
17.REMOVE EXISTING TYPE NM (ROMEX) CABLE IN AREA OFCONSTRUCTION. WHERE EXISTING ROMEX SUPPLIES POWERTO DEVICES ON FLOOR ABOVE, PROVIDE JUNCTION BOXWHERE ROMEX PENETRATES FLOOR AND INSTALL MC CABLEFROM JUNCTION BOX TO EXISTING PANEL. ROMEX CABLE ISNOT PERMITTED ABOVE ANY GRID CEILINGS.
16. REMOVE EXISTING SURFACE MOUNTED RECEPTACLES ANDASSOCIATED SURFACE RACEWAY. VERIFY POWERCONTINUATION AND TERMINATE BRANCH CIRCUIT WIRING INNEAREST ACCESSIBLE JUNCTION BOX. REMOVE EXISTINGBRANCH CIRCUIT WIRING BACK TO SOURCE CIRCUITBREAKER FOR DEDICATED RECEPTACLES.
17. REMOVE EXISTING SURFACE MOUNTED VOICE/DATA OUTLETSAND ASSOCIATED SURFACE RACEWAY. REMOVE VOICE/DATACABLES BACK TO PATCH PANEL.
18. REMOVE EXISTING FIRE ALARM SYSTEM AND ASSOCIATEDCABLING. EXISTING RECESSED DEVICE BOXES ANDCONCEALED RACEWAY SHALL REMAIN AND BE USED FORNEW CONSTRUCTION IF MOUNTING HEIGHT IS PER NFPAGUIDELINES. EXISTING FIRE ALARM SYSTEM SHALL REMAININ OPERATION UNTIL NEW SYSTEM IS INSTALLED.
