7302.10 RAILS, flat bottom, less than 20 kg/m Op. 21.02.1984 Dec. 21.02.1984 - TC 8341714 7302.10 RAILS, crane, railway type, weight EXCEEDING 70 kg/m Op. 14.06.1988 Dec. 18.08.1988 - TC 8805556 7302.10.00 RAIL TRACK, comprising NOT less than 0.84% carbon Op. 10.08.2005 Dec. 28.10.2005 - TC 0510522 7302.10.00 RAIL, having ALL of the following: (a) elevated guardrail configuration; (b) overall height 93 mm; (c) rail head height 38 mm; (d) neck height 40 mm; (e) base (foot) height 15 mm; (f) rail head width 80 mm; (g) base (foot) width 40 mm Op. 22.06.1998 Dec. 28.08.1998 - TC 9805404 7302.10.00 RAIL, TRAMWAY, having ALL of the following: (a) base width 123 mm to 127 mm; (b) overall height 134 mm to 138 mm; (c) rail head width 61 mm to 64 mm; (d) rail head height 39 mm to 42 mm; (e) neck height 72 to 75 mm; (f) heat treated (off-line or in-line head hardened) Op. 30.04.1999 Dec. 09.06.2000 - TC 9902964 7302.30.00 RAIL, ASYMMETRICAL POINTS, having ALL of the following: (a) tongue rail configuration; (b) base width 140 mm; (c) overall height 134 mm; (d) rail head width 74.5 mm; (e) rail head height 53 mm; (f) neck height 47.3 mm Op. 09.04.1998 Dec. 10.06.2010 - TC 1025922 7302.90.00 CLIPS, CRANE RAIL Op. 05.06.2008 Dec. 22.08.2008 - TC 0811455 7303.00.00 PIPES, cast iron, complying with European Standard EN877:1999 (EN877:1999) having EITHER of the following: (a) internal coating of epoxy resin, outer coating of acrylic primer; (b) internal coating of epoxy, outer coating of zinc and acrylic primer Op. 14.09.2006 Dec. 08.12.2006 - TC 0617186 7304.11.00 LINE PIPE, seamless, to DNV-OS-F101 Op. 01.01.2007 Dec. 06.03.2007 - TC 0703466 7304.11.00 LINE PIPE, seamless, stainless steel Op. 04.04.2007 Dec. 22.06.2007 - TC 0704964 7304.19.00 LINE PIPE, seamless, to Specification ASTM A333 Grade 6, having EITHER of the following: (a) OD exceeding 209.0 mm; (b) a WT of 12.5 mm or greater Op. 01.01.2007 Dec. 08.11.2006 - TC 0614208
7304.19.00 TUBES OR HOLLOW BARS (NOT BEING HONED TUBES), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or pipe material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.2007 Dec. 08.11.2006 - TC 0614209 7304.19.00 LINE PIPE, seamless, complying with ISO 3183-3, Grade L450QC, having BOTH of the following: (a) outside diameter greater than 113 mm but NOT greater than 115 mm; (b) wall thickness greater than 4 mm but NOT greater than 5 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614210 7304.19.00 TUBES, seamless, conforming to ALL of the following: (a) specification API 5L-X42 OR API 5L-X60 OR API 5L-B; (b) OD less than 153.4 mm OR greater than 482.3 mm; (c) resistance to stepwise cracking and tested to NACE standard TM02-84 Op. 01.01.2007 Dec. 08.11.2006 - TC 0614211 7304.19.00 PIPES, STEEL, having a diameter NOT less than 65 cm Op. 24.01.2007 Dec. 13.04.2007 - TC 0701302 7304.19.00 LINE PIPE, seamless, to DNV-OS-F101 Op. 01.01.2007 Dec. 06.03.2007 - TC 0703467 7304.23.00 DRILL PIPES, WELLBORE, seamless, having BOTH of the following: (a) outside diameter (OD) NOT greater than 216 mm; (b) tool joint one end Op. 25.11.2009 Dec. 05.02.2010 - TC 0944896 7304.23.00 DRILL PIPES, having rotary connections attached, conforming to API Specification 7, being EITHER of the following: (a) conforming to API Specification 5D; (b) as listed in THE TABLE THE TABLE Outside Diameter Wall Thickness (i) 88 mm to 110 mm (both inclusive) 18 mm or greater; (ii) 110 mm to 120 mm (both inclusive) 20 mm or greater; (iii) 120 mm to 130 mm (both inclusive) 23 mm or greater Op. 01.01.2007 Dec. 09.11.2006 - TC 0614213 7304.23.00 DRILL RODS, FRICTION WELDED, having DIN 17MnV6 steel tool joints Op. 01.01.2007 Dec. 27.03.2007 - TC 0703471
7304.23.00 DRILL PIPE, conforming to American Petroleum Institute Specification 5D:2001 (API 5D:2001), having rotary connection attached Op. 11.11.2008 Dec. 06.02.2009 - TC 0839269 7304.24.00 CASING AND/OR TUBING, STAINLESS STEEL, seamless Op. 10.04.2008 Dec. 04.07.2008 - TC 0803235 7304.29 CASING OR TUBING, oilwell (including casing or tubing with couplings), conforming to EITHER of the following: (a) API Specification 5CT; (b) Manufacturers" Material Specification CR9, CR13, CR22 or CR25 with other requirements to API Specifications 5CT, but NOT including EITHER of the following: (a) plain end casing or tubing; (b) casing with connectors Op. 01.07.1996 Dec. 06.06.1996 - TC 9605808 7304.29 JOINTS, blast, being tubing threaded at both ends, in nominal lengths of 3.05 m or 6.10 m Op. 01.07.1996 Dec. 16.05.1996 - TC 9608624 7304.29.00 CASING OR TUBING, OIL OR GAS WELL, seamless, plain end, diameter NOT exceeding 140 mm Op. 30.08.1999 Dec. 08.11.1999 - TC 9906606 7304.31 TUBE, seamless, cold drawn, having an outside diameter NOT exceeding 8 mm, an inside diameter NOT exceeding 4 mm, pressure rating NOT less than 54 900 kPa, to Specification DIN 2413 Op. 08.05.1989 Dec. 26.07.1990 - TC 8903168 7304.31 TUBES, heat exchange and condenser, seamless, cold drawn, carbon steel, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A179/A 179M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9201981 7304.31 TUBES, seamless, cold drawn, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification DIN standard 2391: Part 2 Op. 10.02.1992 Dec. 16.07.1992 - TC 9202044 7304.31 TUBES, carbon steel, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, conforming to ASTM A179, cold drawn, seamless, having an OD NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 05.03.1992 Dec. 20.07.1992 - TC 9203132 7304.31 TUBES, cold drawn, seamless, to ANY of the following steel grades: (a) K1006; (b) K1016; (c) K1010; (d) K1020; (e) K1026, or ANY of the following tube specifications: (a) JIS G3445 STKM 11-20; (b) BS6323:Part 6:1982; (c) ASTM A513, and having BOTH of the following: (a) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight; (b) OD NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 27.07.1992 Dec. 08.10.1992 - TC 9206994
7304.31.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516769 7304.31.00 TUBES OR HOLLOW BARS, seamless, cold drawn in straight lengths Op. 26.11.1992 Dec. 08.03.1993 - TC 9210246 7304.31.00 SEAMLESS STEEL TUBE, ASTM A210 GR, comprising ALL of the following: (a) outside diameter NOT less than 38 mm; (c) wall NOT less than 2.6 mm; (d) length NOT less than 6 m and NOT greater than 8.3 m Op. 06.04.2004 Dec. 02.07.2004 - TC 0403598 7304.39 TUBES (NOT being honed tubes), seamless, having BOTH of the following: (a) elevated temperature properties conforming to Specification BS 3602 (1978) Grade 360 or AS 1835 TS 5; (b) OD NOT less than 1 250 mm OR a WT NOT exceeding 25 mm Op. 21.03.1985 Dec. 21.03.1985 - TC 8530426 7304.39 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE THE TABLE Outside Diameter Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8735571 7304.39 TUBES, seamless, hot finished, boiler and superheater, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification ASTM A210/A 210M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9201980 7304.39 PIPE, seamless, hot finished, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A333/A333M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202042 7304.39.00 PIPES, seamless, non alloy carbon steel, circular cross section, having an OD (outside diameter) less than 168.3 mm AND complying with ANY of the following standards: (a) American Society for Testing and Materials standard ASTM A106/A106M-08; (b) American Society for Testing and Materials standard ASTM A53/A53M-07, Grade B; (c) American Petroleum Institute standard API Specification 5L, Grade X42 Op. 29.01.2010 Dec. 16.04.2010 - TC 1005214
7304.39.00 PIPES, seamless, non alloy carbon steel, circular cross section, having a wall thickness exceeding 16 mm AND complying with ANY of the following standards: (a) American Society for Testing and Materials standard ASTM A106/A106M-08; (b) American Society for Testing and Materials standard ASTM A53/A53M-07, Grade B; (c) American Petroleum Institute standard API Specification 5L, Grade X42 Op. 29.01.2010 Dec. 16.04.2010 - TC 1005213 7304.39.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516768 7304.39.00 LANCES, MONOLITHIC, INERT GAS, ceramic coated Op. 22.02.2007 Dec. 18.05.2007 - TC 0702193 7304.39.00 PIPES, STEEL, POWER STATION STEAM GENERATION BOILER, being ANY of the following: (a) main and/or auxilary steam pipes; (b) hot reheat pipes; (c) cold reheat pipes; (d) main feed water pipes; (e) super heater pipes Op. 31.08.2007 Dec. 09.11.2007 - TC 0713866 7304.39.00 HOLLOW BARS, seamless, hot rolled or hot finished in straight lengths Op. 22.10.1996 Dec. 06.01.1997 - TC 9611660 7304.39.00 TUBES, seamless, carbon steel, hot finished, in straight lengths, ends plain OR bevelled OR threaded, but without further rework, to specification DIN 1629 Op. 30.12.1996 Dec. 25.03.1997 - TC 9613286 7304.41 TUBES, stainless steel, containing 12% or more chromium, OD NOT exceeding 3.175 mm Op. 28.02.1984 Dec. 28.02.1984 - TC 8341367 7304.41 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8735572
7304.41 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 12% by weight of chromium, having EITHER of the following: (a) OD NOT exceeding 105 mm and WT NOT less than 4.5 mm but NOT exceeding 25 mm; (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8801453 7304.41 TUBES, seamless, stainless steel, plain square cut ends, minimum length 3 000 mm, to Specification ASTM A269, type 316L, having SI. surface finished: O.D. - bright annealed; I.D. - electro polished to RA.4um; or SU. surface finish: O.D. - bright annealed; I.D. - electro polished to RA.8um, in the following sizes: (a) 12.7 mm x 1.651 mm WT; (b) 19.05 mm x 1.651 mm WT; (c) 25.4 mm x 1.651 mm WT; (d) 38.1 mm x 1.651 mm WT; (e) 50.8 mm x 1.651 mm WT; (f) 63.5 mm x 1.651 mm WT; (g) 76.2 mm x 1.651 mm WT; (h) 101.6 mm x 2.108 mm WT; (i) 101.6 mm x 3.175 mm WT; (j) 152.4 mm x 5.004 mm WT Op. 07.10.1991 Dec. 19.02.1992 - TC 9108894 7304.41 PIPES, seamless, stainless steel, to ASTM B407-88 (UNS N08810) having EITHER of the following: (a) OD NOT exceeding 105 mm and a WT NOT less than 4.0 mm but NOT exceeding 25 mm; (b) OD NOT less than 105 mm and a WT NOT exceeding 25 mm Op. 07.01.1992 Dec. 11.05.1992 - TC 9200914 7304.41.00 UMBILICALS, CHEMICAL INJECTION AND HYDRAULIC FLUID, SUBSEA, thermoplastic encapsulated, having a continuous length NOT less than 500 m Op. 05.02.2009 Dec. 08.05.2009 - TC 0903794 7304.41.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516767 7304.41.00 TUBES, cold reduced, stainless steel, carbon content NOT exceeding 0.03%, to specifications ASTM A790, A789 Op. 16.07.1993 Dec. 01.11.1993 - TC 9306991 7304.41.00 TUBING, seamless stainless steel, duplex alloy S.A.F.2205 to ASTM A 789 UNS S31803, having an outside diameter less than 25mm Op. 05.04.1993 Dec. 05.04.1993 - TC 9329022
7304.41.00 TUBE OR PIPE, stainless steel, to specification UNS S31803, having a chemical composition by weight of ALL the following: (a) carbon 0.030% maximum; (b) manganese 2.00% maximum; (c) phosphorus 0.030% maximum; (d) sulphur 0.020% maximum; (e) silicon 1.00% maximum; (f) chromium 21.00 - 23.00% both inclusive; (g) nickel 4.50 - 6.50% both inclusive; (h) nitrogen 0.03 - 0.20% maximum; (i) molybdenum 2.50 - 3.50% both inclusive Op. 25.05.1994 Dec. 26.08.1994 - TC 9404855 7304.41.00 TUBES, seamless, circular cross section, stainless steel, to specification ASTM A269 or ASTM A213, cold drawn and annealed, whether or NOT surface finished, having BOTH of the following: (a) OD NOT exceeding 6.35 mm; (b) WT NOT exceeding 1.20 mm Op. 31.07.1995 Dec. 27.10.1995 - TC 9509324 7304.41.00 TUBES OR PIPES, stainless steel, seamless Op. 25.11.2003 Dec. 08.03.2004 - TC 0314979 7304.49 TUBES, stainless steel, containing 12% or more chromium, OD NOT exceeding 3.175 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8635310 7304.49 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 12% by weight of chromium, having EITHER of the following: (a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT exceeding 25.0 mm; (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm Op. 03.07.1987 Dec. 04.09.1987 - TC 8734525 7304.49 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8735573
7304.49.00 TUBING OR PIPING, seamless stainless steel, having extruded aluminium finning Op. 20.07.2009 Dec. 02.10.2009 - TC 0925796 7304.49.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516766 7304.49.00 HOLLOW BARS, stainless steel, grade 316L or 304L, wrought and fully annealed, in ANY of the following sizes: OUTSIDE DIAMETER INSIDE DIAMETER (a) 118 mm 63 mm (b) 125 mm 71 mm (c) 125 mm 50 mm (d) 132 mm 71 mm (e) 140 mm 80 mm (f) 150 mm 95 mm (g) 150 mm 80 mm (h) 170 mm 118 mm (i) 180 mm 125 mm (j) 190 mm 132 mm (k) 200 mm 140 mm (l) 212 mm 130 mm (m) 224 mm 140 mm (n) 236 mm 150 mm Op. 08.03.1994 Dec. 17.06.1994 - TC 9403562 7304.49.00 PIPES, stainless steel, seamless, bevelled OR plain ends Op. 29.07.1999 Dec. 15.10.1999 - TC 9905670 7304.49.00 TUBES OR PIPES, stainless steel, seamless Op. 25.11.2003 Dec. 08.03.2004 - TC 0314980 7304.51 TUBES, longitudinally finned, extruded Op. 28.02.1984 Dec. 28.02.1984 - TC 8341428 7304.51 PIPE, seamless, cold drawn, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A333/A 333M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202040 7304.51 PIPE, seamless, ferritic alloy steel, cold drawn, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A335/A 335M-89a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202045 7304.51.00 TUBES, threaded, seamless, cold-drawn, having ALL of the following; (a) outside diameter NOT greater than 39 mm; (b) inside diameter NOT greater than 27.6 mm; (c) length NOT greater than 2.6 m Op. 19.05.2009 Dec. 14.08.2009 - TC 0916934 7304.51.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516770 7304.51.00 TUBES, seamless alloy steel, cold drawn, compliant with American Society for Testing and Materials Standard A519/4130 (ASTM A519/4130) Op. 29.02.2008 Dec. 16.05.2008 - TC 0803409
7304.51.00 TUBES OR HOLLOW BARS, seamless, alloy steel, cold rolled or cold finished, in straight lengths Op. 17.06.1993 Dec. 24.09.1993 - TC 9304563 7304.51.00 BARS, HOLLOW, cold drawn, alloy steel, to specification BS6258 OR ISO2938 Op. 19.11.1999 Dec. 31.01.2000 - TC 9908853 7304.59 BARS, hollow, trepanned to Specification AISI 4330H modified, having a length NOT less than 4 times the OD, having ALL of the following: (a) OD 257 mm or greater but NOT exceeding 350 mm; (b) WT 68 mm or greater but NOT exceeding 138 mm; (c) concentricity 3.00 mm total runout Op. 06.06.1985 Dec. 15.11.1985 - TC 8532878 7304.59 TUBES OR PIPES, seamless, tested and certified to EITHER of the following Specifications: (a) ASTM A200 Grade T5; (b) ASTM A335 Grade P5 Op. 01.01.1988 Dec. 01.01.1988 - TC 8801707 7304.59 TUBES, alloy steel, in straight lengths, ends plain, without further rework, to ANY of the following Material Specifications: (a) ASTM A213; (b) ASME A213; (c) BS 3059; (d) AS 1835, having ALL of the following: (a) chromium content, by weight, of 0.7% or greater but NOT exceeding 12.5%; (b) an OD of 30 mm or greater but NOT exceeding 127 mm; (c) WT NOT exceeding 12.5 mm Op. 16.10.1989 Dec. 02.01.1990 - TC 8907466 7304.59 TUBES, boiler, hot finished, seamless ferritic alloy steel, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification ASTM A213/A213M-89a Op. 10.02.1992 Dec. 23.07.1992 - TC 9201989 7304.59 PIPE, seamless ferritic alloy steel, hot finished, in straight lengths, ends plain, bevelled or threaded BUT without further rework, to specification ASTM A335/A 335M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9201999 7304.59 TUBES, seamless alloy steel, hot finished, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification BS3059: Part 2: 1978 Op. 10.02.1992 Dec. 16.07.1992 - TC 9202000 7304.59 PIPE, seamless, hot finished, in straight lengths, ends plain, bevelled or threaded BUT without further rework to specification ASTM A333/A 333M-88a Op. 10.02.1992 Dec. 16.07.1992 - TC 9202039 7304.59.00 TUBES, seamless, alloy steel, forged, in straight lengths, having ALL of the following: (a) length NOT greater than 1 950 mm; (b) outside diameter (OD) NOT greater than 550 mm; (c) wall thickness (WT) NOT less than 70 mm Op. 17.11.2009 Dec. 22.01.2010 - TC 0943497
7304.59.00 PIPES, SEAMLESS, rough machined, comprising ALL of the following: (a) length NOT greater than 4 m; (b) steel to American Society for Testing and Materials Standard A105 (ASTM A105); (c) yield strength greater than 200 MPa; (d) tensile strength greater than 400 MPa; (e) outside diameter (OD) greater than 1 m; (f) wall thickness (WT) greater than 110 mm and NOT greater than 130 mm Op. 22.09.2009 Dec. 04.12.2009 - TC 0935634 7304.59.00 PIPES, STEAM, seamless alloy steel, hot finished, complying with American Society for Testing and Materials ASTM A 335/A 335M Grade P11 and American Society of Mechanical Engineers ASME SA- 335/SA-335M, in the following types or sizes: (a) 500 mm NB Schedule 60 (508.0 mm OD and 20.6 mm WT); (b) 500 mm NB Schedule 120 (508.0 mm OD and 38.1 mm WT); (c) 300 mm NB Schedule 60 (323.8 mm OD and 14.3 mm WT); (d) 250 mm NB Schedule 60 (273.0 mm OD and 12.7 mm WT); (e) 200 mm NB Schedule 100 (219.1 mm OD and 15.1 mm WT); (f) 200 mm NB Schedule 60 (219.1 mm OD and 10.3 mm WT); (g) 150 mm NB Schedule 80 (168.3 mm OD and 11.0 mm WT); (h) 100 mm NB Schedule 80 (114.3 mm OD and 8.6 mm WT); (i) 50 mm NB Schedule 80 (60.3 mm OD and 5.5 mm WT); (j) 25 mm NB Schedule 80 (33.4 mm OD and 4.5 mm WT); (k) 15 mm NB Double Extra Strong XXS(21.3 mm OD and 7.5 mm WT); (l) 15 mm NB Schedule 160 (21.3 mm OD and 4.8 mm WT) For the purposes of this Order, tolerances allowable on the nominal bore (NB), outer diameter (OD) and wall thickness (WT) are + or - 2% Op. 28.07.2009 Dec. 16.10.2009 - TC 0927071 7304.59.00 PIPE AND PIPE FABRICATIONS, alloy steel, with or without clamps AND/OR fittings AND/OR expansion joints, complying with American Society for Testing and Materials specification A335 Grade P91 (ASTM A335 grade P91), having ALL of the following: (a) NOT less than 8% chromium; (b) NOT less than 0.7% molybdenum; (c) NOT less than 0.18% vanadium Op. 24.12.2008 Dec. 20.03.2009 - TC 0845335 7304.59.00 PIPE, alloy steel, complying to American Society for Testing and Materials specification A335 Grade P91 (ASTM A335 grade P91), having ALL of the following: (a) NOT less than 8% chromium; (b) NOT less than 0.7% molybdenum; (c) NOT less than 0.18% vanadium Op. 24.12.2008 Dec. 20.03.2009 - TC 0845156 7304.59.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516771 7304.59.00 PIPES, STEEL, POWER STATION STEAM GENERATION BOILER, being ANY of the following: (a) main steam pipes; (b) hot reheat pipes; (c) cold reheat pipes; (d) main feed water pipes Op. 28.12.2007 Dec. 24.05.2008 - TC 0800039 7304.59.00 RODS, RAISE DRILL, alloy steel, integral Op. 28.04.2008 Dec. 18.07.2008 - TC 0805489
7304.59.00 TUBES, seamless, carbon steel, hot finished in straight lengths, ends plain, bevelled or threaded, but without further rework, to specification AISI 4140 quenched and tempered Op. 09.12.1992 Dec. 30.08.1993 - TC 9310300 7304.59.00 BARS, hollow, to specification AISI 4145H modified Op. 18.04.1994 Dec. 22.07.1994 - TC 9404209 7304.59.00 TUBES OR PIPES, seamless, conforming to EITHER of the following specifications: (a) SA-213 T22; (b) SA-335 P22 Op. 01.11.1996 Dec. 31.01.1997 - TC 9611933 7304.59.00 TUBES, seamless, alloy steel, hot finished, annealed, in straight lengths, ends plain OR bevelled OR threaded, but without further rework, to specification AISI 4140 Op. 30.12.1996 Dec. 25.03.1997 - TC 9613287 7304.59.00 DRILL STRING SECTIONS, THREADED, ROTARY PERCUSSIVE ROCK DRILLING, being ANY of the following: (a) hollow drill tube; (b) hollow bar and rod external cross section dimension exceeding 52 mm, and a maximum internal dimension greater than one half of the maximum external cross section dimension Op. 16.05.1997 Dec. 01.08.1997 - TC 9704455 7304.59.00 TUBES OR PIPES, seamless alloy steel, hot finished, to ASTM A519 Grade 4140 Op. 08.01.1998 Dec. 13.03.1998 - TC 9800163 7304.59.00 DRILL RODS, ROTARY PERCUSSIVE ROCK DRILLING, hollow, threaded OR tapered, external cross-section dimension exceeding 52 mm Op. 10.08.1998 Dec. 16.10.1998 - TC 9807063 7304.59.00 BARS, HOLLOW, hot rolled, alloy steel to specification BS6258 OR ISO2938 Op. 19.11.1999 Dec. 31.01.2000 - TC 9908840 7304.59.00 TUBES, hot rolled, seamless alloy steel to specification DIN1629 Op. 19.11.1999 Dec. 31.01.2000 - TC 9908842 7304.59.00 LANCES, OXYGEN OR INERT GAS, ceramic coated Op. 08.12.2000 Dec. 02.03.2001 - TC 0010030 7304.59.00 TUBES OR HOLLOW BARS, seamless, alloy steel, hot finished OR hot rolled, in straight lengths Op. 09.11.2004 Dec. 21.01.2005 - TC 0411761 7304.90.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 07.09.2005 Dec. 16.01.2006 - TC 0511817 7305.11.00 LINE PIPE, submerged arc welded, complying with ISO 3183-3, Grade L450, having BOTH of the following: (a) outside diameter greater than 1 400 mm; (b) wall thickness greater than 29 mm but NOT greater than 31 mm Op. 17.06.2005 Dec. 09.09.2005 - TC 0507512
7305.11.00 LINE PIPE, OIL AND GAS, complying with American Petroleum Institute (API) Standard, Specification 5L, Grade B, Production Specification Level (PSL) 1, having ALL of the following: (a) varnish coatings; (b) length NOT less than 12 metres; (c) bevelled ends; (d) wall thickness NOT less than 9 mm and NOT greater than 13 mm; (e) outside diameter NOT less than 640 mm and NOT greater than 800 mm; (f) longitudinally submerged arc welding; but NOT including spirally submerged arc welded steel line pipe complying with Australian Standard AS 1579 Op. 10.04.2007 Dec. 12.09.2007 - TC 0705206 7305.11.00 PIPES, LINE, steel, complying with American Petroleum Institute (API) Standard, Specification 5L, grade X60, Product Specification Level (PSL) 2, having ALL of the following: (a) bevelled ends; (b) wall thickness NOT less than 17.5 mm; (c) outside diameter NOT less than 1422 mm; (d) longitudinally double submerged arc welded Op. 28.03.2008 Dec. 20.06.2008 - TC 0804996 7305.11.00 PIPE, SUBMERGED ARC WELDED (SAW), having EITHER of the following: (a) outside diameter NOT less than 750 mm; (b) wall thickness NOT less than 9.53 mm Op. 27.08.2008 Dec. 09.02.2009 - TC 0828344 7305.11.00 LINE PIPE, submerged arc welded, to DNV-OS-F101 Op. 04.11.2004 Dec. 01.02.2005 - TC 0411588 7305.12.00 LINE PIPE, OIL AND GAS PIPELINE, steel, having BOTH of the following: (a) diameter NOT less than 645 mm; (b) longitudinally welded Op. 23.04.2007 Dec. 16.07.2007 - TC 0705875 7305.12.00 LINE PIPE, OIL AND GAS, stainless steel, welded, having an external diameter NOT less than 406.4 mm Op. 31.07.2008 Dec. 24.10.2008 - TC 0824211 7305.12.00 PIPE, to specification API 5L Grade B, ASTM 53B, being EITHER of the following sizes (+/- 10%): (a) OD 762 mm, WT 9.5 mm; (b) OD 760 mm, WT 9.5 mm Op. 17.06.2004 Dec. 03.09.2004 - TC 0405928 7305.12.00 PIPE, seamed, ERW, to specification API 5L Grade B, being ANY of the following sizes (+/- 10%): (a) OD 609.6 mm, WT 9.5 mm; (b) OD 508 mm, WT 9.5 mm; (c) OD 508 mm, WT 15.1 mm; (d) OD 406.4 mm, WT 16.7 mm Op. 24.06.2004 Dec. 11.08.2004 - TC 0407961 7305.12.00 LINE PIPE, electric resistance welded, to DNV-OS-F101 OR DEP 31.40.20.37 Op. 04.11.2004 Dec. 01.02.2005 - TC 0411589
7305.19.00 STEEL PIPE, spirally welded, conforming to American Petroleum Institute Specification 5L (API 5L), Grade B steel, having ALL of the following: (a) length NOT greater than 12 m; (b) diameter NOT less than 762 mm; (c) NOT less than three layers of polyethylene; (d) maximum pressure rating 2.7 MPa Op. 27.01.2009 Dec. 24.04.2009 - TC 0902849 7305.20.00 CONDUCTOR CASING, OILWELL, to API specification 5L, with OR without connectors, having BOTH of the following: (a) outside diameter exceeding 500 mm; (b) wall thickness exceeding 20 mm Op. 30.07.1998 Dec. 23.10.1998 - TC 9806755 7305.20.00 CYLINDERS, STEEL, DRILL HOLE CASING Op. 05.11.2003 Dec. 23.01.2004 - TC 0314142 7305.31 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 10% by weight of chromium, having EITHER of the following: (a) OD NOT less than 1 250 mm; (b) WT 5 mm or greater but NOT exceeding 25 mm Op. 03.07.1987 Dec. 04.09.1987 - TC 8734523 7305.31.00 STEEL PIPE, electric resistance welded, conforming to American Petroleum Institute Specification 5L (API 5L), Grade B steel, having ALL of the following: (a) length NOT greater than 12 m; (b) diameter NOT less than 762 mm; (c) NOT less than three layers of polyethylene; (d) maximum pressure rating 2.7 MPa; (e) rubber inserts Op. 27.01.2009 Dec. 24.04.2009 - TC 0902680 7305.31.00 WELD TEST RINGS, complying with Offshore Standard for Submarine Pipeline Systems DNV-OS-F101 Op. 08.12.2005 Dec. 08.03.2006 - TC 0604839 7305.39.00 STEEL PIPE, spirally welded, conforming to American Petroleum Institute Specification 5L (API 5L), Grade B steel, having ALL of the following: (a) length NOT greater than 12 m; (b) diameter NOT less than 762 mm; (c) NOT less than three layers of polyethylene; (d) maximum pressure rating 2.7 MPa; (e) rubber inserts Op. 27.01.2009 Dec. 24.04.2009 - TC 0902682 7305.39.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516772 7305.90.00 SECTIONS, TUNNEL, galvanised steel, corrugated Op. 17.04.2008 Dec. 11.07.2008 - TC 0804357 7306.11.00 LINE PIPE, complying with DNV-OS-F101 Op. 01.01.2007 Dec. 02.01.2007 - TC 0614759
7306.19.00 PIPE, ELECTRIC RESISTANCE WELDED, exceeding a wall thickness of 12.7 mm Op. 22.02.2008 Dec. 20.11.2009 - TC 0943624 7306.19.00 TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following tube, hollow bar or Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, having a length NOT less than four times the OD, as listed in THE TABLE: THE TABLE Outside Dia Wall Thickness (a) NOT exceeding 219.08 mm 13.00 mm or greater but NOT exceeding 25.00 mm; (b) 219.08 mm or greater but 12.70 mm or greater but NOT exceeding 254.00 mm NOT exceeding 50.80 mm; (c) 254.00 mm or greater but 19.05 mm or greater but NOT exceeding 323.85 mm NOT exceeding 41.00 mm; (d) 323.85 mm or greater but 25.40 mm or greater but NOT exceeding 720.73 mm NOT exceeding 75.00 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614214 7306.19.00 PIPE, to specification API 5L Grade B, ASTM 53B, being ANY of the following sizes (+/- 10%): (a) OD 114.3 mm, WT 6.0 mm; (b) OD 88.9 mm, WT 5.5 mm; (c) OD 60.3 mm, WT 3.9 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614217 7306.19.00 LINE PIPE, complying with DNV-OS-F101 Op. 01.01.2007 Dec. 02.01.2007 - TC 0614760 7306.19.00 PIPES, WELDED, complying with American Petroleum Institute Standard Specification of Line Pipe 5L, comprising ALL of the following: (a) outside diameter NOT less than 63 mm and NOT greater than 115 mm; (b) wall thickness NOT less than 4 mm and NOT greater than 11 mm; (c) yield strength capacity NOT less than 385 MPa Op. 26.02.2007 Dec. 18.05.2007 - TC 0703024 7306.19.00 TUBES OR PIPES, ERW, bevelled ends, certified to ALL the following specifications: (a) AS 1163; (b) API 5L grades B and X42; (c) ASTM A53 grade B; in ANY of the following sizes: Cross Section Diameter Wall Thickness Length NOT less than 88.5 mm and NOT less than 4 mm and NOT less than NOT greater than 90 mm NOT greater than 10 mm 6 m NOT less than 114 mm and NOT less than 4 mm and NOT less than NOT greater than 115 mm NOT greater than 10 mm 6 m NOT less than 141 mm and NOT less than 4 mm and NOT less than NOT greater than 142 mm NOT greater than 10 mm 6 m Op. 06.11.2003 Dec. 23.10.2008 - TC 0835803
7306.29.00 TUBING, electrical resistance welded, coiled OR in spools, having BOTH of the following: (a) minimum continuous length of 2 000 m; (b) minimum OD of 31 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614219 7306.29.00 CASING, Electric Resistance Welded (ERW), complying with American Petroleum Institute 5CT (API 5CT) having BOTH of the following: (a) outside diameter of 406.4mm; (b) wall thickness exceeding 10 mm but NOT exceeding 14 mm For the purposes of this Order, tolerances of + or - 1% are allowable for the specification in (a) Op. 01.01.2007 Dec. 29.11.2006 - TC 0614773 7306.29.00 TUBES, electric resistance welded, having BOTH of the following: (a) outside diameter NOT greater than 50.8 mm; (b) external upset or non upset connections complying with American Petroleum Institute (API) Specification 5CT Op. 16.12.2008 Dec. 06.03.2009 - TC 0844063 7306.30 PIPES, lance, oxygen calorised and ceramic coated Op. 22.08.1991 Dec. 25.05.1992 - TC 9107706 7306.30 TUBES, ERW boiler, being EITHER carbon or carbon manganese steel, in straight lengths, ends plain, bevelled or threaded, BUT without further rework, to specification ASTM A178/A 178M-89 Op. 10.02.1992 Dec. 16.07.1992 - TC 9201983 7306.30 TUBES, cold drawn, welded, to ANY of the following steel grades: (a) K1006; (b) K1016; (c) K1010; (d) K1020; (e) K1026, or ANY of the following tube specifications: (a) JIS G3445 STKM 11-20; (b) BS6323:Part 6:1982; (c) ASTM A513, and having BOTH of the following: (a) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight; (b) OD NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 27.07.1992 Dec. 08.10.1992 - TC 9206993 7306.30 TUBES, cold drawn, welded, to specification ASTM A513, having BOTH of the following: (a) OD NOT less than 203.2mm and NOT greater than 306.0mm; (b) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight Op. 04.09.1992 Dec. 31.12.1992 - TC 9208087 7306.30.00 TUBES, cold drawn, welded, to JIS G3473 STC 590A E-C stress relieved Op. 10.10.2005 Dec. 03.01.2006 - TC 0514065 7306.30.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516774 7306.30.00 TUBES, welded, nickel coated, complying with Japanese Industrial Standard G3445 STKM11A (JIS G3445 STKM11A) Op. 29.01.2007 Dec. 20.04.2007 - TC 0701552
7306.30.00 TUBES, welded, complying with Japanese Industrial Standard G3445 STK11A (JIS G3445 STKM11A), having an outside diameter NOT greater than 12 mm Op. 07.02.2007 Dec. 20.04.2007 - TC 0701959 7306.30.00 TUBES, cold drawn, welded to specification DIN 2393, having BOTH of the following: (a) carbon content NOT less than 0.06% and NOT greater than 0.4% by weight; (b) outside diameter NOT less than 6.4 mm and NOT greater than 203.2 mm Op. 28.06.1995 Dec. 29.09.1995 - TC 9508551 7306.30.00 TUBES, welded, having ALL of the following: (a) externally plated; (b) internally copper coated; (c) nominal OD 10.00 mm (+/- 0.1 mm); (d) nominal WT 0.70 mm (+/- 0.1 mm) Op. 04.10.1995 Dec. 05.01.1996 - TC 9511080 7306.30.00 TUBES OR PIPES, ERW, conforming to specification SA 178 Op. 01.11.1996 Dec. 20.01.1997 - TC 9611935 7306.30.00 TUBES, cold drawn, welded, stress relieved, to DIN specification 2393, having ALL of the following: (a) outside diameter of 15 mm to 22 mm; (b) inside diameter of 13 mm to 19 mm; (c) wall thickness of 1 mm to 1.6 mm Op. 16.04.2002 Dec. 05.07.2002 - TC 0203211 7306.30.00 TUBES, WELDED, non alloy steel, being EITHER of the following: (a) single wall resistance welded to specification SAE J526, having ALL of the following: (i) carbon content NOT greater than 0.13%; (ii) outside diameter NOT greater than 11.50 mm; (iii) wall thickness NOT less than 0.5 mm and NOT greater than 1.0 mm; (b) double wall copper brazed to specification SAE J527, having ALL of the following: (i) carbon content NOT greater than 0.13%; (ii) outside diameter NOT greater than 13 mm; (iii) wall thickness NOT less than 0.5 mm and NOT greater than 1.0 mm Op. 31.03.2003 Dec. 27.06.2003 - TC 0303383 7306.40 TUBES, stainless steel, longitudinally welded, having BOTH of the following dimensions: (a) an OD 105 mm or greater but NOT exceeding 220 mm; (b) a WT 1.50 mm or greater but NOT exceeding 5.00 mm Op. 30.04.1985 Dec. 05.09.1985 - TC 8531977 7306.40 TUBES, alloy steel, in straight lengths, ends plain, bevelled or threaded in accordance with ANY of the following Pipe Material Specification options: (a) AS; (b) ASME; (c) ASTM; (d) BS; (e) DIN, but without further rework, containing NOT less than 12% by weight of chromium, having EITHER of the following: (a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT exceeding 25.0 mm; (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm
Op. 01.01.1988 Dec. 01.01.1988 - TC 8733276 7306.40.00 UMBILICALS, CHEMICAL INJECTION, SUBSEA, thermoplastic- encapsulated tubes Op. 17.06.2005 Dec. 09.09.2005 - TC 0507509 7306.40.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516775 7306.40.00 TUBES OR PIPES, stainless steel, to specification UNS S31803, having chemical composition by weight of ALL the following: (a) carbon : 0.030% maximum; (b) manganese : 2.00% maximum; (c) phosphorus : 0.030% maximum; (d) sulphur : 0.020% maximum; (e) silicon : 1.00% maximum; (f) chromium : 21.00 - 23.00% both inclusive; (g) nickel : 4.50 - 6.50% both inclusive; (h) nitrogen : 0.03 - 0.20% maximum; (i) molybdenum : 2.50 - 3.50% both inclusive Op. 06.06.1994 Dec. 09.09.1994 - TC 9405021 7306.50 TUBES, ERW steel, aluminium killed, having BOTH of the following: (a) OD exceeding 103 mm; (b) WT 2 mm or less Op. 28.02.1984 Dec. 28.02.1984 - TC 8341256 7306.50.00 WELD TEST RINGS, complying with DNV-OS-F101 Op. 08.12.2005 Dec. 03.03.2006 - TC 0516776 7306.50.00 TUBES, ERW, aluminized, type JIS G3445, having ALL of the following: (a) 12.7 mm OD; (b) 1.6 mm WT; (c) 5 700 mm mill length Op. 14.04.1994 Dec. 29.07.1994 - TC 9404172 7306.61.00 TUBES, rectangular, stainless steel, NOT less than 100 mm x 50 mm across the flat dimensions Op. 01.01.2007 Dec. 09.11.2006 - TC 0614222 7306.61.00 TUBES, square, stainless steel, NOT less than 100 mm x 100 mm across the flat dimension Op. 01.01.2007 Dec. 09.11.2006 - TC 0614223 7306.61.00 RECTANGULAR HOLLOW SECTIONS, welded carbon steel, in straight lengths, ends plain, without further rework, having overall dimensions of 101.6 mm x 101.6 mm and wall thickness greater than 9.5 mm Op. 01.01.2007 Dec. 09.11.2006 - TC 0614224 7306.61.00 TUBES, cold drawn, carbon steel, hollow frame profile, having ANY of the following sectional dimensions: Length Width Wall Thickness (a) 90 mm 41 mm 2.0 mm; (b) 104 mm 43 mm 2.5 mm; (c) 104 mm 43 mm 3.0 mm Op. 01.01.2007 Dec. 08.05.2007 - TC 0705890 7306.61.00 DUCTS, RECTANGULAR HOLLOW PROFILES, STEAM GENERATION PLANT Op. 07.10.2008 Dec. 12.01.2009 - TC 0834441
7307.19.00 FITTINGS, pipe, B.S.P thread, made of galvanised malleable iron, to BS 1256, being ANY of the following: (a) elbows, 90 degrees, being EITHER, female to female, or male to female; (b) elbows, 45 degrees, being female to female; (c) elbows, 3 way; (d) elbows, reducing, 90 degrees; (e) tees, including 4 way, and reducing tees; (f) bush, hexagon; (g) caps; (h) crosses; (i) backnuts; (j) nipples, being ANY of the following: (i) hexagon; (ii) barrel; (iii) plain; (iv) reducing; (k) sockets including reducing sockets; (l) plugs, square head; (m) bends, 90 degrees, EITHER, male to female, or female to female; (n) bends, 45 degrees, male to female; (o) unions, EITHER, male to female, or female to female Op. 06.07.1993 Dec. 08.10.1993 - TC 9306802 7307.19.00 PIPE FITTINGS, POTABLE WATER AND GAS LINES, being EITHER of the FOLLOWING: (a) malleable cast iron couplings, incorporating a rubber seal and washer (b) tapped OR non tapped plugs incorporating a rubber seal Op. 23.05.1996 Dec. 06.09.1996 - TC 9607790 7307.21.00 FLANGES, PIPE, stainless steel, seamless Op. 29.07.1999 Dec. 15.10.1999 - TC 9905666 7307.22.00 FITTINGS, TUBE, stainless steel, with OR without seals, being threaded bends Op. 31.03.2010 Dec. 09.07.2010 - TC 1015482 7307.22.00 FITTINGS, VACUUM, stainless steel, operating pressure lower than 133 x 0.0000001 MPa, being EITHER of the following: (a) couplings; (b) elbows Op. 18.12.1997 Dec. 27.02.1998 - TC 9711204 7307.23 BENDS, CROSSES, ELBOWS OR TEES, buttweld, stainless steel, conforming dimensionally to ANY of the following Specifications: (a) BS 1640; (b) ANSI B16.9; (c) ANSI B16.28 Op. 28.02.1984 Dec. 28.02.1984 - TC 8341312 7307.23 FITTINGS, stainless steel, tube or pipe, buttweld, annealed, internally polished Op. 23.11.1987 Dec. 23.02.1989 - TC 8735514 7307.23 FITTINGS, seamless, stainless steel grade 316L, to specification ASTM 269 or ASTM 270, electropolished internally through entire length Op. 20.05.1988 Dec. 02.05.1989 - TC 8805455
7307.23.00 INDUCTION BENDS, LINE PIPE, with or without concrete coating, having BOTH of the following: (a) duplex stainless steel having an outside diameter NOT less than 168.3 mm (6 inch nominal size); (b) compliance with Det Norske Veritas Offshore Standard F101 (DNV-OS-F101) Op. 28.04.2009 Dec. 17.07.2009 - TC 0914018 7307.29 RINGS, gasket or packing, to API Specification 6A, capable of operating at temperatures of 125 degrees C or greater Op. 30.12.1987 Dec. 27.04.1988 - TC 8733301 7307.29.00 FITTINGS, TUBE, stainless steel, with OR without seals, being ANY of the following: (a) couplings having a diameter NOT greater than 200 mm; (b) reducers; (c) bends; (d) T junctions; (e) union connectors; (f) adapters Op. 29.04.2010 Dec. 09.07.2010 - TC 1019464 7307.29.00 FITTINGS, PIPE AND TUBE, Grade 316L stainless steel, push fit, with or without seal, being ANY of the following: (a) pipe incorporating a socket; (b) bends; (c) pipe, having NOT less than 45 degree junctions and NOT greater than 90 degree junctions; (d) double sockets; (e) "P" traps; (f) bottle trap; (g) eccentric increasers; (h) eccentric reducers; (i) access bends; (j) threaded adaptor Op. 25.02.2010 Dec. 14.05.2010 - TC 1009883 7307.29.00 FITTINGS, DRAINAGE, Grade 316L stainless steel, being ALL of the following: (a) filter baskets; (b) removable water traps; (c) grates Op. 25.02.2010 Dec. 14.05.2010 - TC 1009880 7307.29.00 FITTINGS, PIPE AND TUBE, stainless steel, being ANY of the following: (a) sealing rings; (b) bodies; (c) cap nuts; (d) weld cones; (e) flare adaptors Op. 11.03.2009 Dec. 06.11.2009 - TC 0941426 7307.29.00 FITTINGS, CAMLOCK, being ANY of the following: (a) male sections and/or female sections; (b) plugs; (c) caps Op. 20.12.2007 Dec. 07.03.2008 - TC 0710840
7307.29.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the following; (a) male sections; (b) female sections; (c) lever rings; (d) male plugs; (e) female caps Op. 21.12.2007 Dec. 07.03.2008 - TC 0721937 7307.29.00 COUPLINGS, HOSE, quick connect, comprising ALL of the following: (a) male sections; (b) female sections; (c) lever rings Op. 21.12.2007 Dec. 14.03.2008 - TC 0721940 7307.29.00 FITTINGS, ROOF DRAINAGE, stainless steel, being ANY of the following: (a) rainwater outlets; (b) hoppers; (c) elbows; (d) s-curves; (e) pipe flaps including sets of 2 or more of the above Op. 14.10.2008 Dec. 14.01.2009 - TC 0835301 7307.29.00 COUPLINGS, camlocking, to material 316 stainless steel, 15 mm to 200 mm, inclusive of both adaptors (male) and couplers (female). Op. 13.08.1993 Dec. 10.02.1994 - TC 9307389 7307.29.00 JOINTS, swivel, stainless steel, v-ring type, pressure rating greater than 6 800 KPa Op. 14.06.1993 Dec. 23.09.1993 - TC 9314494 7307.29.00 FITTINGS, pipe, forged stainless steel to specification type F 51 ASTM UNS S 31803, having the surface descaled by turning Op. 27.05.1994 Dec. 02.09.1994 - TC 9404892 7307.29.00 FITTINGS, vacuum, stainless steel, helium leak tested, rated to lower than 133 x 10 -7 MPa, being ANY of the following: (a) plug; (b) cap; (c) gland; (d) body; (e) female nut; (f) male nut; (g) bodies, assembled with nuts and ferrules; (h) assemblies including ANY of the above Op. 22.05.1997 Dec. 15.08.1997 - TC 9704622 7307.29.00 COUPLINGS, FLOW, OIL AND GAS WELL, stainless steel Op. 15.12.1997 Dec. 27.02.1998 - TC 9711103 7307.91.00 FLANGES, DOWNTAKE PIPE, WALKING BEAM FURNACE, being ANY of the following: (a) DN 200; (b) DN 300; (c) DN 350; (d) DN 400 Op. 25.11.2005 Dec. 13.02.2006 - TC 0516608
7307.91.00 FLANGES, PIPE, being ANY of the following: (a) weld neck flanges; (b) blind flanges; (c) spectacle blind flanges; (d) slip on flanges; (e) socket weld flanges; (f) threaded flanges; (g) bulkhead flanges Op. 20.02.2008 Dec. 02.05.2008 - TC 0803404 7307.91.00 FLANGE ADAPTERS, PIPE OR TUBE OR HOSE, carbon steel, with or without seal Op. 03.12.2008 Dec. 27.02.2009 - TC 0842547 7307.91.00 FLANGES, HOT FORGED, SEAMLESS, comprising ALL of the following: (a) inner diameter NOT less than 1 500 mm; (b) width NOT greater than 400 mm; (c) outer diameter NOT less than 2 000 mm Op. 09.10.2003 Dec. 03.03.2004 - TC 0312809 7307.92.00 ELBOWS, threaded Op. 08.10.2008 Dec. 14.01.2009 - TC 0834585 7307.92.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with or without seal, being ANY of the following: (a) elbows, 90 degrees; (b) elbows, 45 degrees; (c) elbows, 3 way tees, being either male to female OR combinations of both; (d) tube sleeves; (e) bends, 90 degrees; (f) bends, 45 degrees Op. 03.12.2008 Dec. 27.02.2009 - TC 0842548 7307.92.00 FITTINGS, pipe, steel, complying with standards BS1740 or AS3672 Op. 10.05.1994 Dec. 19.08.1994 - TC 9404635 7307.92.00 FITTINGS, PIPE AND TUBE, including sealing rings, bodies, nuts and weld cones, having BOTH of the following: (a) compliance with pressure rating of either LL, L or S to DIN 2353; (b) interchangeability of the whole or any component of the fitting with other fittings or components which comply with the dimensional specifications set out in DIN 2353, but NOT including ANY of the following: (a) stainless steel fittings; (b) twin ferrule fittings Op. 03.11.1995 Dec. 09.02.1996 - TC 9511750 7307.92.00 FITTINGS, TUBE, elbow, carbon steel, twin ferrule Op. 18.11.1997 Dec. 23.01.1998 - TC 9710155 7307.93 FITTINGS, buttweld, in accordance with Dimensional Specification MSS-SP75 and Material Specification API 5LX Op. 28.02.1984 Dec. 28.02.1984 - TC 8341295 7307.93 FITTINGS, buttweld pipe, being ANY of the following: (a) to ASTM Specification A420 GRWPL6: (i) elbows, 45 degrees; (ii) elbows, 90 degrees, OD NOT exceeding 304.8 mm; (iii) reducers, eccentric; (b) to ASTM Specification A234 GRWP1: (i) elbows, 45 degrees or 90 degrees, OD NOT exceeding 254 mm;
(ii) reducers, eccentric, OD at larger end NOT exceeding 254 mm Op. 28.02.1984 Dec. 28.02.1984 - TC 8341297 7307.93 FITTINGS, being ANY of the following: (a) elbows to ASTM Specification A234 WPB, having a dia less than 406.4 mm OD; (b) reducers to ASTM Specification A234 WPB, having BOTH diameters less than 406.4 mm OD; (c) elbows, reducers or tees to ASTM Specification A234 WP 11 Op. 19.10.1987 Dec. 21.12.1987 - TC 8735075 7307.93 JOINTS, insulating, monobloc or monolithic Op. 01.01.1988 Dec. 01.01.1988 - TC 8803112 7307.93.00 PARTS, BOILER INSPECTION BUTTWELD FITTINGS, being EITHER of the following: (a) butt weld hubs; (b) blind hubs Op. 03.02.2010 Dec. 23.04.2010 - TC 1005997 7307.93.00 FITTINGS, BUTTWELD, STEEL PIPE OR TUBE, having ALL of the following: (a) inspection cap; (b) clamp assembly consisting of BOTH of the following: (i) clamp segments; (ii) studs and nuts, (c) seal ring; (d) butt welding hub Op. 15.12.2009 Dec. 05.03.2010 - TC 0948886 7307.93.00 FITTINGS, PIPE OR TUBE, butt-welded, forged steel, being reinforced and contoured connections Op. 28.07.2009 Dec. 16.10.2009 - TC 0927139 7307.93.00 FITTINGS, PIPE AND/OR TUBE, butt weld, alloy steel, being end caps Op. 28.07.2009 Dec. 09.10.2009 - TC 0927136 7307.93.00 INDUCTION BENDS, LINE PIPE, with or without concrete coating, with or without internal corrosion resistant cladding, having BOTH of the following: (a) carbon steel having an outside diameter NOT less than 355.6 mm (14 inch nominal size); (b) compliance with Det Norske Veritas Offshore Standard F101 (DNV-OS-F101) Op. 29.04.2009 Dec. 17.07.2009 - TC 0914155 7307.93.00 FITTINGS, BUTTWELD, being ANY of the following: (a) bends; (b) crosses; (c) elbows; (d) reducers; (e) tees Op. 06.06.2005 Dec. 24.10.2005 - TC 0506772 7307.93.00 FITTINGS, forged buttweld, welded or seamless, carbon steel to specification ASTM A234 WPB, OR duplex steel to specification ASTM A 790 UNS31803, being transition pieces having full flow characteristics, ranging in size from 150 mm to 300 mm nominal bore, round at one end and oval at the other, with wall thickness ranging from 2.41 mm to 21.44 mm Op. 05.05.1993 Dec. 13.08.1993 - TC 9305531
7307.93.00 FITTINGS, buttweld, forged, integrally reinforced, contoured-insert vessel or piping branch connections, bore sizes 15 mm - 1 200 mm Op. 01.03.1993 Dec. 04.06.1993 - TC 9308562 7307.93.00 REDUCERS, buttweld, having a minimum outside diameter between 70 mm and 200 mm (+ or - 0.001%) Op. 11.02.1998 Dec. 11.05.1998 - TC 9801278 7307.93.00 FITTINGS, buttweld, to specifications BS1640 OR ANSI B16.9 OR ANSI B16.28, being ANY of the following: (a) bends, 30 degrees, 45 degrees, 50 degrees, 60 degrees, 90 degrees OR 180 degrees, having an outside diameter between 17 mm and 406.4 mm; (b) tees, equal OR reducing, having an outside diameter of 406.4 mm OR less For the purposes of this order, ALL measurements have a tolerance of + OR - 5% Op. 11.02.1998 Dec. 12.08.1998 - TC 9806998 7307.99 ELBOWS, socketweld, being ANY of the following: (a) 15 degrees; (b) 45 degrees; (c) 90 degrees ID exceeding 50.8 mm Op. 06.03.1984 Dec. 06.03.1984 - TC 8341420 7307.99 JOINTS, insulating, monobloc or monolithic Op. 28.02.1984 Dec. 28.02.1984 - TC 8341449 7307.99 PLUGS, pipe, incorporating an oil resistant synthetic rubber seal capable of sealing pipes having an ID of 49 mm or greater but NOT exceeding 356 mm at pressures of 48 MPa or less Op. 28.02.1984 Dec. 28.02.1984 - TC 8341450 7307.99 COUPLINGS, hose, having a working capacity of 206 MPa or greater Op. 30.10.1984 Dec. 30.10.1984 - TC 8434699 7307.99 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising male and female ring lock couplings, hinged ring band snap lock and double lip gasket, to suit pipes and hoses having an OD of 50 mm or greater Op. 14.12.1984 Dec. 30.04.1985 - TC 8530126 7307.99 UNIONS, hammer, being four lug wing nut type with replaceable rubber seal, having ANY of the following nominal connecting pipe sizes on slipfit female pipe end and in Schedule 80 buttweld, male component weld end: Nominal connecting Nominal size pipe size (female end) pipe (weld end) Outside Dia Outside Dia (a) 114.3 mm 152.4 mm; (b) 168.28 mm 203.2 mm; (c) 219.08 mm 254.0 mm; (d) 273.05 mm 304.8 mm; (e) 323.85 mm 355.6 mm; (f) 355.6 mm 406.4 mm; (g) 406.4 mm 457.2 mm Op. 21.04.1987 Dec. 27.08.1987 - TC 8733860 7307.99 RINGS, gasket or packing, to API Specification 6A, capable of operating at temperatures of 125 degrees C or greater Op. 01.01.1988 Dec. 27.04.1988 - TC 8802330 7307.99 FITTINGS, pipe, fluoro-polymer lined Op. 12.02.1988 Dec. 21.12.1988 - TC 8802801
7307.99 FITTINGS, steel pipe, being EITHER of the following: (a) three lug wing nut unions, dia NOT exceeding 300 mm, minimum operating pressure 6.80 MPa; (b) hub clamp assemblies, consisting of ALL of the following: (i) clamp segments; (ii) hubs; (iii) seal ring Op. 23.02.1988 Dec. 16.09.1988 - TC 8802877 7307.99 COUPLINGS, casing or tubing, seamless to Specification API-5CT, section 8 Op. 05.12.1988 Dec. 07.06.1989 - TC 8902264 7307.99 JOINTS, swivel, pressure rating over 40 MPa Op. 23.04.1991 Dec. 02.09.1991 - TC 9104099 7307.99 CLAMPS, pipe repair (but NOT including clamps incorporating stainless steel flexible bands), having ALL of the following characteristics: (a) seal by ANY of the following methods: (i) clamping or thrust screws; (ii) girder rings; (iii) packing or force screws; (b) carbon steel construction; (c) of fixed dia; (d) capable of withstanding a working pressure of 6 900 kPa or greater Op. 01.01.1988 Dec. 11.09.1992 - TC 9206167 7307.99 CLOSURES, pressurised pipeline, hinged, quick release, diameter 150 mm or greater, but NOT including screw top type closures Op. 13.07.1992 Dec. 08.10.1992 - TC 9206615 7307.99.00 TERMINATION HEADS, subsea Op. 05.01.2009 Dec. 27.03.2009 - TC 0946016 7307.99.00 OILWELL CONNECTORS, having ALL of the following: (a) nonhelical interlocking teeth; (b) metal to metal seals; (c) diameter NOT less than 50.8 cm Op. 29.07.2005 Dec. 07.10.2005 - TC 0509995 7307.99.00 FITTINGS, COUPLING, HOSE, quick connect, being ANY of the following: (a) male sections; (b) female sections; (c) lever rings; (d) male plugs; (e) female caps Op. 21.12.2007 Dec. 07.03.2008 - TC 0721938 7307.99.00 COUPLINGS, HOSE, QUICK CONNECT, comprising ALL of the following; (a) male sections; (b) female sections; (c) lever ring Op. 21.12.2007 Dec. 07.03.2008 - TC 0721939 7307.99.00 FITTINGS, PIPE, being EITHER of the following: (a) hot tap; (b) line stop Op. 21.04.2008 Dec. 11.07.2008 - TC 0804852 7307.99.00 FITTINGS, PIPE, being bulkhead flange seals Op. 27.05.2008 Dec. 15.08.2008 - TC 0810189
7307.99.00 CONNECTORS, HYDRAULIC HOSE, steel Op. 13.08.2008 Dec. 31.10.2008 - TC 0826255 7307.99.00 FITTINGS, PIPE, forged, integrally reinforced, contoured-insert vessel or piping branch connections, having a bore size NOT less than 15 mm and NOT greater than 1 200 mm Op. 04.09.2008 Dec. 28.11.2008 - TC 0829428 7307.99.00 FITTINGS, ROOF DRAINAGE, galvanized steel, being ANY of the following: (a) rainwater outlets; (b) inclined outlets; (c) hoppers; (d) elbows; (e) s-curves; (f) hinged outlets; (g) pipe flaps including sets of 2 or more of the above Op. 14.10.2008 Dec. 14.01.2009 - TC 0835300 7307.99.00 FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with or without seal, being ANY of the following: (a) reducing or enlarging bush, hexagon; (b) caps, solid or swivel; (c) crosses; (d) nipples, being ANY of the following: (i) hexagon; (ii) barrel; (iii) plain; (iv) reducing; (e) sockets, including reducing and enlarging; (f) plugs, square head or hex head or internal or external hexagon; (g) unions; (h) tube welds or weld-on's; (i) tube compression and tube flared fittings Op. 03.12.2008 Dec. 27.02.2009 - TC 0842546 7307.99.00 FITTINGS, pipe and tube, metric, including sealing rings, bodies and nuts, to specifications DIN 2353 or DIN 3859 in ANY of the following sizes: (a) 4 mm; (b) 6 mm; (c) 8 mm; (d) 10 mm; (e) 12 mm; (f) 14 mm; (g) 15 mm; (h) 16 mm; (i) 18 mm; (j) 20 mm; (k) 22 mm; (l) 25 mm; (m) 28 mm; (n) 30 mm; (o) 35 mm; (p) 38 mm; (q) 42 mm; (r) 50 mm Op. 02.12.1993 Dec. 11.04.1994 - TC 9400309
7307.99.00 COUPLINGS, pipe or hose, quick connect (or disconnect), comprising male and female ring lock couplings, hinged ring band snap lock, to suit pipes and hoses having an OD of 50 mm or greater Op. 24.02.1994 Dec. 03.06.1994 - TC 9402433 7307.99.00 FITTINGS, pipe, high pressure, steel, complying with ALL the following standards: (a) ASTM A105; (b) ANSI B16.11; (c) BS3799 Op. 27.04.1994 Dec. 29.07.1994 - TC 9404403 7307.99.00 BRANCH CONNECTIONS, weld on type, complying with ALL the following standards: (a) ASTM A105; (b) ANSI B31-1 1980; (c) ANSI B16-9; (d) BS3351 1971 Op. 27.04.1994 Dec. 05.08.1994 - TC 9404404 7307.99.00 FITTINGS, pipe and tube, including sealing rings, bodies, nuts and weld cones, having BOTH of the following: (a) compliance with pressure rating being either LL, L or S to DIN 2353; (b) interchangeability of the whole or any component of the fitting with other fittings or components which comply with the dimensional specifications set out in DIN 2353, but NOT including ANY of the following: (a) stainless steel fittings; (b) twin ferrule fittings Op. 25.11.1994 Dec. 14.03.1995 - TC 9409468 7307.99.00 FITTINGS, STEEL, being EITHER of the following: (a) hose couplings having a female ACME coupling connection within the range of 44.45 mm to 82.55 mm (both inclusive); (b) adapters with male ACME connection within the range of 44.45 mm to 82.55 mm (both inclusive) Op. 14.02.1995 Dec. 20.10.1995 - TC 9501971 7307.99.00 FITTINGS, PIPE, unthreaded, being ANY of the following: (a) joining rings having a diameter of 80 mm or greater but NOT exceeding 800 mm; (b) pressed bends of galvanised or mild steel in angles from 7.5 degrees or greater but NOT exceeding 90 degrees and diameter of 80 mm or greater but NOT exceeding 400 mm; (c) straight ducting with fully rolled beaded edge having a diameter of 155 mm or greater but NOT exceeding 160 mm; but NOT including fittings of stainless steel Op. 31.08.1995 Dec. 08.12.1995 - TC 9510236 7307.99.00 CLOSURES, PRESSURISED PIPELINE, having ALL of the following: (a) a cap; (b) a welding hub, with an integrated semi-dovetailed O-Ring groove in the face; (c) capable of horizontal, vertical or angle installations Op. 22.03.1996 Dec. 28.06.1996 - TC 9604891 7307.99.00 FITTINGS, TUBE, carbon steel, twin ferrule Op. 17.11.1997 Dec. 23.01.1998 - TC 9710154 7307.99.00 FITTINGS, ON-LINE HYDRAULIC LINE TESTING, being couplers, adaptors OR stand pipes, working pressures up to 40 MPa in hose sizes 2 mm and 4 mm Op. 10.12.1997 Dec. 27.02.1998 - TC 9710916
(l) swivel beam clamps; (m) board clamps Op. 07.01.2008 Dec. 25.03.2008 - TC 0800330 7308.40.00 SCAFFOLDING, NOT including walk boards and mesh guards Op. 06.06.2007 Dec. 22.01.2008 - TC 0801189 7308.90 RAILS, elevator guide, weight less than 6 kg/m or exceeding 26 kg/m Op. 28.02.1984 Dec. 28.02.1984 - TC 8437468 7308.90 CRASH CUSHIONS, roadside hazard, energy absorbing, meeting NCHRP 230 Test tolerances Op. 18.11.1988 Dec. 19.10.1990 - TC 8810530 7308.90.00 PANELS, BUILDING, having ALL of the following: (a) mineral wool core; (b) steel face thickness NOT less than 0.45 mm and NOT greater than 0.735 mm; (c) panel thickness NOT less than 50 mm and NOT greater than 250 mm; (d) core sheer strength NOT less tan 80 kN/m2 and NOT greater than 90 kN/m2; (e) fire resistance level NOT less than -/30/30, in accordance with Australian Standard 1530.4-2005 (AS 1530.4-2005); (f) tongue and groove interlock joint Op. 24.03.2010 Dec. 18.06.2010 - TC 1014366 7308.90.00 PANELS, INSULATING, consisting of polyurethane inner core with galvanised steel sheeting BOTH sides, having BOTH of the following: (a) steel sheet thickness NOT less than 0.4 mm; (b) polyurethane thickness NOT less than 20 mm Op. 27.07.2009 Dec. 09.10.2009 - TC 0926917 7308.90.00 SUPPORT GANTRIES, GYRATORY CRUSHER, structural steel, having ALL of the following: (a) frames; (b) plates; (c) grating; (d) stairways; (e) stairway treads; (f) handrails; (g) stanchions; (h) platforms; (i) walkways; (j) ladders, with or without ladder cages Op. 09.06.2009 Dec. 04.09.2009 - TC 0919374 7308.90.00 MARINE PILINGS, steel, having ALL of the following: (a) thickness NOT less than 20 mm; (b) length NOT less than 28.5 m; (c) diameter NOT less than 900 mm; (d) maximum of one splice per piling; (e) maximum straightness difference of 1 mm per metre over entire length Op. 30.04.2009 Dec. 24.07.2009 - TC 0914435 7308.90.00 FIXTURES, LOAD BEARING, as defined in European Technical Approval 06/0131 (ETA 06/0131), having a weight load pressure equal to or greater than 100 MPa at 30 degrees C Op. 29.04.2009 Dec. 17.07.2009 - TC 0914303
7308.90.00 PARTS, STRUCTURAL STEEL, COAL PLANT OR IRON ORE PLANT, being ANY of the following: (a) rolled, hollow or welded sections; (b) beams; (c) grating, (d) stairways and/or treads; (e) plates; (f) handrails (with or without kick plates); (g) stanchions; (h) purlins and girts; (i) packing and shims; (j) guards; (k) platforms; (l) walkways; (m) ladders; (n) legs; (o) trusses or trestles; (p) stringer and ground modules; (q) frames; (r) wear liners; (s) gantries Op. 12.05.2008 Dec. 01.08.2008 - TC 0807603 7308.90.00 STRUCTURES, WELLHEAD, OFFSHORE OIL AND GAS, comprising ALL of the following: (a) well head platform jacket structural steel sections; (b) piles having lengths NOT less than 28 m; (c) pile inserts having lengths NOT less than 18 m Op. 11.06.2008 Dec. 08.09.2008 - TC 0812032 7308.90.00 DUCTS, INLET, GAS TURBINE, consisting of ALL of the following: (a) transition and extension ducting; (b) expansion joints; (c) elbows; (d) cladding; (e) shims; (f) press plates Op. 07.08.2008 Dec. 31.10.2008 - TC 0825492 7308.90.00 INLET TRANSITION DUCTS, GAS TURBINE, consisting of ALL of the following: (a) roof panels; (b) floor panels; (c) lateral panels; (d) dihedral assemblies; (e) bracing; (f) supports Op. 07.08.2008 Dec. 31.10.2008 - TC 0825493 7308.90.00 BOOM OR BULKHEAD, MOVEABLE, SWIMMING POOL Op. 11.08.2008 Dec. 31.10.2008 - TC 0825894 7308.90.00 INLET SUPPORT STRUCTURE, GAS TURBINE GENERATOR, including ALL of the following: (a) beams; (b) columns; (c) bracings; (d) stairways; (e) handrails Op. 18.08.2008 Dec. 07.11.2008 - TC 0826878
7310.29.00 TINS, NOVELTY, having less than 220 grams of confectionery and/or bakers wares Op. 15.09.2005 Dec. 25.11.2005 - TC 0512191 7310.29.00 TINS, DISPLAY, having BOTH of the following: (a) tin sheet thickness NOT less than 0.2 mm and NOT greater than 0.4 mm; (b) transparent display windows Op. 29.12.2006 Dec. 23.03.2007 - TC 0620288 7310.29.00 TINS, PACKAGING, printed, with or without hinged lid, capacity NOT greater than 3.5 kg Op. 26.11.2008 Dec. 27.02.2009 - TC 0841237
