+ All Categories
Home > Documents > CUT_200-300-400-Sp__Data Sheet_EN

CUT_200-300-400-Sp__Data Sheet_EN

Date post: 02-May-2017
Category:
Upload: moustaffa
View: 214 times
Download: 0 times
Share this document with a friend
4
Machine Type of machining Submerged Submerged Submerged wire-cutting wire-cutting wire-cutting Dimensions of complete equipment (*) mm 2020 x 2201 x 2015 2600 x 2600 x 2340 2670 x 2870 x 2645 in. 79.53 x 86.65 x 79.33 102.36 x 102.36 x 92.13 105.12 x 112.99 x 104.13 Total weight of equipment kg 2450 3300 6300 (without dielectric) lbs. 5401 7275 13860 Machining area Max. workpiece dimensions (*) mm 1000 x 550 x 220 1200 x 700 x 400 1450 x 900 x 510 in. 39.37 x 21.65 x 8.66 47.24 x 27.56 x 15.75 57.09 x 35.43 x 20.07 Front door dimensions mm 820 1020 1350 in. 32.28 40.16 53.1 Max. workpiece weight kg 750 1500 3000 lbs. 1653 3307 6600 Dimensions of table (**) mm 680 x 450 900 x 600 1240 x 800 in. 26.77 x 17.72 35.43 x 23.62 48.8 x 31.5 Floor-to-table distance mm 1000 1000 1100 in. 39.37 39.37 43.30 Total volume of dielectric l 760 1200 1700 gal. 201 317 450 X, Y, Z and U, V axes X, Y, Z travel (*) mm 350 x 220 x 220 550 x 350 x 400 800 x 550 x 510 in. 13.77 x 8.66 x 8.66 21.65 x 13.77 x 15.75 31.5 x 21.65 x 20.07 U, V travel (**) mm 350 x 220 550 x 350 800 x 550 in. 13.77 x 8.66 21.65 x 13.77 31.5 x 21.65 Rapid movement (X, Y and U, V axes) m/min 3 3 3 ft/min 9.8 9.8 9.8 Integrated Collision Protection (ICP) Standard on 5 axes Standard on 5 axes Standard on 5 axes Taper machining Max. taper °/mm ± 45/220 ± 45/400 ± 45/510 (± 30/220 standard) (± 30/400 standard) (± 30/510 standard) °/ in. ± 45/8.66 ± 45/15.75 ± 45/20.07 (± 30/8.66 standard) (± 30/15.75 standard) (± 30/20.07 standard) Electricity supply (machine) Three-phase input voltage V 380/400 Maximum consumption kVA 11 CUT 200 Sp CUT 300 Sp CUT 400 Sp Technical Data CUT 200 Sp, CUT 300 Sp, CUT 400 Sp * Width x depth x height ** Width x depth
Transcript
Page 1: CUT_200-300-400-Sp__Data Sheet_EN

MachineType of machining Submerged Submerged Submerged wire-cutting wire-cutting wire-cuttingDimensions of complete equipment (*) mm 2020 x 2201 x 2015 2600 x 2600 x 2340 2670 x 2870 x 2645 in. 79.53 x 86.65 x 79.33 102.36 x 102.36 x 92.13 105.12 x 112.99 x 104.13

Total weight of equipment kg 2450 3300 6300(without dielectric) lbs. 5401 7275 13860

Machining area Max. workpiece dimensions (*) mm 1000 x 550 x 220 1200 x 700 x 400 1450 x 900 x 510 in. 39.37 x 21.65 x 8.66 47.24 x 27.56 x 15.75 57.09 x 35.43 x 20.07Front door dimensions mm 820 1020 1350 in. 32.28 40.16 53.1Max. workpiece weight kg 750 1500 3000 lbs. 1653 3307 6600Dimensions of table (**) mm 680 x 450 900 x 600 1240 x 800 in. 26.77 x 17.72 35.43 x 23.62 48.8 x 31.5Floor-to-table distance mm 1000 1000 1100 in. 39.37 39.37 43.30Total volume of dielectric l 760 1200 1700 gal. 201 317 450

X, Y, Z and U, V axes X, Y, Z travel (*) mm 350 x 220 x 220 550 x 350 x 400 800 x 550 x 510 in. 13.77 x 8.66 x 8.66 21.65 x 13.77 x 15.75 31.5 x 21.65 x 20.07U, V travel (**) mm 350 x 220 550 x 350 800 x 550 in. 13.77 x 8.66 21.65 x 13.77 31.5 x 21.65Rapid movement (X, Y and U, V axes) m/min 3 3 3 ft/min 9.8 9.8 9.8Integrated Collision Protection (ICP) Standard on 5 axes Standard on 5 axes Standard on 5 axes

Taper machining Max. taper °/mm ± 45/220 ± 45/400 ± 45/510 (± 30/220 standard) (± 30/400 standard) (± 30/510 standard) °/ in. ± 45/8.66 ± 45/15.75 ± 45/20.07 (± 30/8.66 standard) (± 30/15.75 standard) (± 30/20.07 standard)

Electricity supply (machine)Three-phase input voltage V 380/400Maximum consumption kVA 11

CUT 200 Sp CUT 300 Sp CUT 400 Sp

Technical DataCUT 200 Sp, CUT 300 Sp, CUT 400 Sp

* Width x depth x height ** Width x depth

Page 2: CUT_200-300-400-Sp__Data Sheet_EN

Wire circuit Wire diameters available mm 0.33 to 0.070 (standard: 0.33 to 0.15) 0.30 to 0.20 in. 0.013 to 0.003 (standard: 0.013 to 0.006) 0.012 to 0.008Type of wire guides Closed diamond type without clearancePermissible weights and types of spool kg 1.6 (K100) to 8 (K160) 25 (K250) (ISO standards) lbs. 3.52 (K100) to 17.6 (K160) 55 (K250)Permissible weights and types of spool kg 3 (P3) to 5 (P5) (JIS standards) lbs. 6.6 (P3) to 11 (P5)Programmable wire tension daN 0.3 to 3Automatic threading for wire mm 0.33 to 0.070 (0.33 to 0.15 standard) 0.30 to 0.20 in. 0.013 to 0.004 (0.012 to 0.05 standard) 0.012 to 0.008Automatic rethreading for wire mm 0.33 to 0.10 (0.33 to 0.15 standard) 0.30 to 0.20 in. 0.013 to 0.004 (0.012 to 0.05 standard) 0.012 to 0.008DielectricPaper filters 2 cartridges (option 4 cartridges)Dielectric temperature variation ° C ± 1 ° F ± 2Total volume of deionization resin (option) l 20 gal. 5.3Max. injection pressure bar 20

CC high speed generator Protection against electrolytic effects From roughing through to finishingMax. cutting speed mm2/min 400 in2/hour 37.7Min. finishing µm Ra 0.1 (4 µ-inch RMS) 0.2 (8.2 µ-inch RMS)

CUT 200 Sp / CUT 300 Sp CUT 400 Sp

NC functionsFile managementAC CAM EASYEDM-EXPERTOPERATIONS ORgANIZERFast measuring cycles3D graphic simulationIntegrated documentationPART EXPRESSJob listSURFACE-EXPERTPOWER-EXPERTPROFIL-EXPERT

Numerical control Position measurement system Linear glass scalesMeasurement resolution 0.050 µm (0.000002 in.)Architecture PC multiprocessorsOperating system WindowsDual check safetyScreen LCD 15” TFTData input Touch screenKeyboard Standard alphanumeric, PC styleRemote control StandardPart program capacity 4 MBEthernet, USB ports StandardDigital dielectric management

OptionsLarge spools kg 16 (K200), 25 (K250) Standard lbs. 35.2 (K200), 55 (K250)TAPER-EXPERT Option Optione-Connect, e-Supervision, e-Control Option OptionExtended taper cutting ° from 30 to 45 from 30 to 45Used wire processing Wire chopper StandardRotating axes Index or servo-control —Automatic Part Leveling 3D SET UP —Optical measuring system OMS —3D probing Renishaw probe Renishaw probe

Page 3: CUT_200-300-400-Sp__Data Sheet_EN

CUT 200 Sp

CUT 300 Sp

1900/74.80”

2020/79.53”

2201

/86.

65”

2280/89.76”

2600/102.36”

240/

9.45

450/

17.7

2”70

/2.7

6”

650/

25.5

9”

60/2

.36”

590/

23.2

3”

X = 350/13.78”

820/32.28”

1040/40.94”

50/1.97”

370/14.57”

680/26.77”

Y =

220/

8.66

370/

14.5

7”

600/

23.6

2”70

/2.7

6”

800/

31.4

9”

Y =

350/

13.7

8”

740/

29.1

3”

X = 550/21.65”

1020/40.16”

1240/48.82”

50/1.97”

570/22.44”

900/35.43”

60/2

.36”

1000/39.37” 2015/79.33”

2200/86.61”

650/25.59”1650/61.42”

2600/102.36”

1630

/64.

17”

630/

24.8

0”

1000

/39.

37” 23

40/9

2.13

Page 4: CUT_200-300-400-Sp__Data Sheet_EN

Achieve more...

CUT 400 Sp

© A

gie

Cha

rmill

es S

A, 2

013

The

tech

nica

l dat

a an

d ill

ustr

atio

ns a

re n

ot b

indi

ng.

They

are

not

war

rant

ed c

hara

cter

isti

cs a

nd a

re s

ubje

ct to

cha

nge.

2870

/112

.99”

2670/105.12”

570/

22.4

4”

800/

31.4

9”11

5/4.

53”

1030

/40.

55”

X = 800/31.50”

1350/53.15”

1500/59.05”

Y =

550/

21.6

5”

940/

37.0

1”90

/3.5

4”

50/1.97”

820/32.28”

1240/48.82”

2645

/104

.13”

108042.52”

259.

805.

512


Recommended