AC centrifugal fan forward curved, dual inlet with housing (without flange) D2E133-AM47-94 ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 · D-74673 Mulfingen Phone +49 7938 81-0 Fax +49 7938 81-110 [email protected]www.ebmpapst.com Limited partnership · Headquarters Mulfingen County court Stuttgart · HRA 590344 General partner Elektrobau Mulfingen GmbH · Headquarters Mulfingen County court Stuttgart · HRB 590142 Nominal data Type D2E133-AM47-94 Motor M2E068-DF Phase 1~ 1~ 1~ 1~ Nominal voltage VAC 230 230 230 230 Frequency Hz 50 50 60 60 Type of data definition ml fa ml ml Valid for approval / standard UL 2111 Speed min -1 1830 1500 1800 1800 Power input W 165 190 200 210 Current draw A 0.73 0.84 0.88 0.92 Motor capacitor μF 3 3 3 3 Capacitor voltage VDB 450 450 450 450 Capacitor standard UL Min. back pressure Pa 80 0 100 100 Min. ambient temperature °C -25 -25 -25 -25 Max. ambient temperature °C 50 35 25 25 Starting current A 0.9 0.9 0.9 ml = max. load · me = max. efficiency · fa = running at free air · cs = customer specs · cu = customer unit Subject to alterations Item no. 10430-5-9980 · Revision 66668 · Release 2010-08-26 · Page 1 / 5 ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
Transcript
AC centrifugal fanforward curved, dual inletwith housing (without flange)
Type of data definition ml fa ml mlValid for approval / standard UL 2111Speed min-1 1830 1500 1800 1800Power input W 165 190 200 210Current draw A 0.73 0.84 0.88 0.92Motor capacitor µF 3 3 3 3Capacitor voltage VDB 450 450 450 450Capacitor standard ULMin. back pressure Pa 80 0 100 100Min. ambient temperature °C -25 -25 -25 -25Max. ambient temperature °C 50 35 25 25Starting current A 0.9 0.9 0.9ml = max. load · me = max. efficiency · fa = running at free air · cs = customer specs · cu = customer unitSubject to alterations
AC centrifugal fanforward curved, dual inletwith housing (without flange)
D2E133-AM47-94
Technical features
Mass 3.48 kgSize 133 mmSurface of rotor Partially cast in aluminiumMaterial of impeller Sheet steel, hot-galvanisedHousing material Sheet steel, hot-galvanisedMotor suspension Motor mounted via brackets on one sideDirection of rotation Clockwise, seen on rotorType of protection IP 44; Depending on installation and positionInsulation class "B"Humidity class F0Max. permissible ambient motortemp. (transp./ storage)
+ 80 °C
Min. permissible ambient motortemp. (transp./storage)
- 40 °C
Mounting position AnyCondensate discharge holes NoneOperation mode S1Motor bearing Ball bearingTouch current acc. IEC 60990(measuring network Fig. 4, TNsystem)
< 0.75 mA
Motor protection Thermal overload protector (TOP) wired internallyCable exit AxialProtection class I (if protective earth is connected by customer)Product conforming to standard EN 60335-1; CE
Air performance measured as per ISO 5801Installation category A. For detailedinformation on the measuring set-up, pleasecontact ebm-papst. Suction-side noiselevels: LwA measured as per ISO 13347 /LpA measured with 1m distance to fan axis.The values given are valid under themeasuring conditions mentioned above andmay vary according to the actual installationsituation. With any deviation from thestandard set-up, the specific values have tobe checked and reviewed with the unitinstalled.
Measured values
1234
UV230230230230
fHz50505050
nmin-1
1500189023102570
Pe
W190164141118
IA0.840.720.610.52
qvm3/h710640460295
pfs
Pa0100200275
U = Supply voltage · f = Frequency · n = Speed · Pe = Power input · I = Current draw · qv = Air flow · pfs = Pressure increase
Air performance measured as per ISO 5801Installation category A. For detailedinformation on the measuring set-up, pleasecontact ebm-papst. Suction-side noiselevels: LwA measured as per ISO 13347 /LpA measured with 1m distance to fan axis.The values given are valid under themeasuring conditions mentioned above andmay vary according to the actual installationsituation. With any deviation from thestandard set-up, the specific values have tobe checked and reviewed with the unitinstalled.
Measured values
1234
UV230230230230
fHz60606060
nmin-1
1800231026852945
Pe
W200181170159
IA0.880.780.740.70
qvm3/h565425300180
pfs
Pa100200300375
U = Supply voltage · f = Frequency · n = Speed · Pe = Power input · I = Current draw · qv = Air flow · pfs = Pressure increase
