Dallas County Community College District Purchasing Department 4343 IH-30 Mesquite, Texas 75150-2018 December 12, 2017 ADDENDUM NO. 1 BID NO. 12430 REMODEL TWO RESTROOMS DISTRICT SERVICE CENTER Opening Date: January 10, 2017 2:00 p.m. Please take note that the above referenced Request for Bid is amended as follows: 1. Sheet A2.01 Plan No. 3 – Enlarged Dimension Plan a. Removed toilet accessory from plan that was previously deleted from project scope. b. Revised location of soap dispensers. c. Revised location of water closet to comply with TAS. 2. Sheet A2.01 – Demolition Plan Key Notes a. Revised General Note #5 to indicate removal of gyp-board with removal of tile on walls. 3. Sheet A2.02 Plan No. 1 – New Construction & Finish Plans a. Added indication of door pulls on both sides of toilet compartment doors near latch to comply with TAS. 4. Sheet A2.02 – New Construction Plan Key Notes a. Revised General Note#12 to indicate new gyp-board on walls. 5. Sheet A3.01 Elevation 1 – Restroom Elevations & Sections a. Added height dimensions for accessible reach to toilet accessories. 6. Sheet A3.01 Elevation 2 & 3 – Restroom Elevations & Sections a. Added plumbing below sink. 7. Sheet A3.01 Elevation 4 – Restroom Elevations & Sections a. Added dimensions from center of water closet to end of grab bar. 8. Sheet A3.01 Elevation 5 – Restroom Elevations & Sections a. Added dimension to indicate seat height of water closet.
Transcript
Dallas County Community College District Purchasing Department 4343 IH-30 Mesquite, Texas 75150-2018
December 12, 2017 ADDENDUM NO. 1 BID NO. 12430 REMODEL TWO RESTROOMS DISTRICT SERVICE CENTER Opening Date: January 10, 2017
2:00 p.m. Please take note that the above referenced Request for Bid is amended as follows: 1. Sheet A2.01 Plan No. 3 – Enlarged Dimension Plan
a. Removed toilet accessory from plan that was previously deleted from project scope. b. Revised location of soap dispensers. c. Revised location of water closet to comply with TAS.
2. Sheet A2.01 – Demolition Plan Key Notes
a. Revised General Note #5 to indicate removal of gyp-board with removal of tile on walls. 3. Sheet A2.02 Plan No. 1 – New Construction & Finish Plans
a. Added indication of door pulls on both sides of toilet compartment doors near latch to comply with TAS.
4. Sheet A2.02 – New Construction Plan Key Notes
a. Revised General Note#12 to indicate new gyp-board on walls. 5. Sheet A3.01 Elevation 1 – Restroom Elevations & Sections
a. Added height dimensions for accessible reach to toilet accessories. 6. Sheet A3.01 Elevation 2 & 3 – Restroom Elevations & Sections
a. Revised location of toilet paper dispenser to comply with TAS. 11. Sheet A3.01 Elevation 9 – Restroom Elevations & Sections
a. Added height dimensions for accessible reach to toilet accessories. 12. Sheet A3.01 Elevation 10 – Restroom Elevations & Sections
a. Added plumbing below sink. There are no further changes/additions at this time. If there are any questions concerning this request for bid, please contact the Purchasing Department at 972/860-7771. END OF ADDENDUM
WOMEN'S RESTROOM
MEN'S RESTROOM
SCALE:
1
DCCCD DISTRICT SERVICE CENTER
BREAKROOM
LOBBY
PAINT P1 - REFER TO 02/A2.02
WOMEN'S RESTROOM
MEN'S RESTROOM
A2.01
DEMOLITION &
PROPOSED FLOOR
PLANS
GENERAL NOTES
RCP KEYNOTES
SCALE: 1/4" = 1'-0"
4
ENLARGED REFLECTED CEILING PLAN
SCALE: 1/4" = 1'-0"
3
ENLARGED DIMENSION PLAN
SCALE: 1/4" = 1'-0"
2
ENLARGED DEMOLITION PLAN
DEMOLITION PLAN KEYNOTES
CHANDANA
D E S G N
5646 Milton Street, Suite 427
Dallas, Texas 75206
t: 214.217.7227
www.chandanadesign.com
DC
CC
D D
ISTR
IC
T SER
VIC
E C
EN
TER
Ren
ovatio
n o
f P
urch
asin
g D
ep
t R
estro
om
s
4343 IH
-30
Mesq
uite, TX
75150
CO
NSTR
UC
TIO
N D
OC
UM
EN
T P
AC
KA
GE
No. DateRevisions / Issue
Seal
Sheet Number
Project Number
Date
Sheet Title
Client
Project
DALLAS COUNTY COMMUNITY COLLEGE DISTRICT
PERMIT SET
201622
10.27.2017
IGSTE S
RNE
SA
ET
STA
IRE
G
39
OF
6 9ET
X
E
IDREIONTER
R
R D
D
ANA
CA N
NA
NH
AYA
10/27/2017
AutoCAD SHX Text
A2.01
AutoCAD SHX Text
2,3,4
AutoCAD SHX Text
1/8" = 1'-0"
AutoCAD SHX Text
P1
AutoCAD SHX Text
1
AutoCAD SHX Text
7
AutoCAD SHX Text
2
AutoCAD SHX Text
4
AutoCAD SHX Text
5
AutoCAD SHX Text
6
AutoCAD SHX Text
1
AutoCAD SHX Text
10
AutoCAD SHX Text
3
AutoCAD SHX Text
8
AutoCAD SHX Text
2
AutoCAD SHX Text
4
AutoCAD SHX Text
5
AutoCAD SHX Text
6
AutoCAD SHX Text
8
AutoCAD SHX Text
3
AutoCAD SHX Text
9
AutoCAD SHX Text
9
AutoCAD SHX Text
2
AutoCAD SHX Text
2
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
3
AutoCAD SHX Text
EXISTING CEILING ACCESS PANEL
AutoCAD SHX Text
1/A3.1
AutoCAD SHX Text
2/A3.1
AutoCAD SHX Text
5/A3.1
AutoCAD SHX Text
10/A3.1
AutoCAD SHX Text
3/A3.1
AutoCAD SHX Text
7/A3.1
AutoCAD SHX Text
7/A3.1
AutoCAD SHX Text
9/A3.1
AutoCAD SHX Text
4/A3.1
AutoCAD SHX Text
8/A3.1
AutoCAD SHX Text
6/A3.1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
A. REFER TO GENERAL CONSTRUCTION NOTES ON SHEET G0.01. REFER TO GENERAL CONSTRUCTION NOTES ON SHEET G0.01. B. REFER TO ENLARGED PLAN FOR TOILET FIXTURE, TOILET REFER TO ENLARGED PLAN FOR TOILET FIXTURE, TOILET ACCESSORIES, AND PARTITION DEMOLITION. C. CONTRACTOR SHALL VERIFY THAT ACCESS PANELS ARE INSTALLED CONTRACTOR SHALL VERIFY THAT ACCESS PANELS ARE INSTALLED IN A NON-ACCESSIBLE TYPE CEILING WHERE SERVICE OR ADJUSTMENTS TO MECHANICAL , PLUMBING, OR ELECTRICAL ITEMS MAY BE REQUIRED. ACCESS PANELS SHALL BE THE FIRE RATED TYPE EQUAL TO THE RATING OF THE WALL OR CEILING IN WHICH THEY OCCUR. D. SCHEDULE ALL DEMOLITION AND NEW CONSTRUCTION WITH THE SCHEDULE ALL DEMOLITION AND NEW CONSTRUCTION WITH THE OWNER. E. REMOVE EXISTING FLOOR AND WALL FINISH, NOT LIMITED TO REMOVE EXISTING FLOOR AND WALL FINISH, NOT LIMITED TO CERAMIC TILE, WALL BASE, WITHIN SCOPE OF WORK IN TOILETS. F. REFER TO ENLARGED FINISH PLANS FOR INTERIOR FINISH MATERIAL REFER TO ENLARGED FINISH PLANS FOR INTERIOR FINISH MATERIAL DESIGNATIONS IN PLAN 02/A2.02. G. REFER TO ENLARGED NEW CONSTRUCTION PLANS FOR ANNOTATION REFER TO ENLARGED NEW CONSTRUCTION PLANS FOR ANNOTATION RE: 01/A2.02
AutoCAD SHX Text
INSTALL NEW LIGHT FIXTURES. REFER TO MPE PLANS. REPLACE EXISTING CEILING VENTS. REFER TO MPE DRAWINGS. PROVIDE NEW CEILING ACCESS PANEL. REFER TO MPE FOR LOCATION.
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
3
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
REMOVE EXISTING PLASTIC LAMINATE COUNTERTOP, BACKSPLASH AND SUPPORTS. REMOVE EXISTING PLUMBING FIXTURES, FITTINGS, ACCESSORIES, WALL ANCHORS AND DAMAGED PIPES. RETURN FIXTURES AND ACCESSORIES TO OWNER IF REUSABLE FOR ATTIC STOCK. CONTRACTOR SHALL NOTIFY OWNER, FACILITIES STAFF ONCE FIXTURES & TILE HAVE BEEN REMOVED FROM THE WALL TO ALLOW FOR INSPECTION OF EXISTING PIPE CONDITIONS. REMOVE EXISTING TOILET PARTITIONS. REMOVE EXISTING TOILET ACCESSORIES, INCLUDING BUT NOT LIMITED TO TOILET PAPER HOLDER, MIRROR, PAPER TOWEL DISPENSER, SOAP DISPENSER, AND TRASH RECEPTACLES. REMOVE EXISTING WAINSCOT OF CERAMIC WALL TILE; FULL LENGTH AND HEIGHT OF WALL AND PREPARE FOR NEW GYPBOARD. PROTECT BRICK ON ADJACENT WALL NOT BEING REMOVED. REMOVE EXISTING CERAMIC FLOOR TILE, AND BASE AT PERIMETER OF SPACE. PROTECT BRICK WALL NOT BEING REMOVED. REMOVE STAINLESS PLATE AND CUT CLEAN-OUT PIPE TO BE FLUSH WITH NEW FINISHED WALL. REFER TO MPE DRAWINGS. REMOVE EXISTING LIGHT FIXTURES IN RESTROOMS AND REPLACE WITH NEW. REFER TO MPE DRAWINGS. REMOVE AND REPLACE DAMAGED CEILING FIXTURES AS REQUIRED. REFERENCE MPE DRAWINGS. REMOVE EXISTING AUTOMATIC DOOR PUSH PLATE ON EXISTING TOILET PARTITION. TURN OVER TO OWNER. PATCH AND REPAIR GYP WALL TO MACH ADJACENT SURFACE.
AutoCAD SHX Text
1
AutoCAD SHX Text
2
AutoCAD SHX Text
3
AutoCAD SHX Text
4
AutoCAD SHX Text
5
AutoCAD SHX Text
6
AutoCAD SHX Text
7
AutoCAD SHX Text
8
AutoCAD SHX Text
9
AutoCAD SHX Text
10
AutoCAD SHX Text
I G N
AutoCAD SHX Text
1
AutoCAD SHX Text
ADDENDUM NO.1
AutoCAD SHX Text
12/11/17
AutoCAD SHX Text
1
A2.02
NEW CONSTRUCTION &
FINISH PLANS
CHANDANA
D E S G N
5646 Milton Street, Suite 427
Dallas, Texas 75206
t: 214.217.7227
www.chandanadesign.com
DC
CC
D D
ISTR
IC
T SER
VIC
E C
EN
TER
Ren
ovatio
n o
f P
urch
asin
g D
ep
t R
estro
om
s
4343 IH
-30
Mesq
uite, TX
75150
CO
NSTR
UC
TIO
N D
OC
UM
EN
T P
AC
KA
GE
No. DateRevisions / Issue
Seal
Sheet Number
Project Number
Date
Sheet Title
Client
Project
DALLAS COUNTY COMMUNITY COLLEGE DISTRICT
PERMIT SET
201622
10.27.2017
IGSTE S
RNE
SA
ET
STA
IRE
G
39
OF
6 9ET
X
E
IDREIONTER
R
R D
D
ANA
CA N
NA
NH
AYA
10/27/2017
GENERAL NOTES
NEW CONSTRUCTION PLAN
KEYNOTES
SCALE: 1/4" = 1'-0"
2
ENLARGED FINISH PLAN
SCALE: 1/4" = 1'-0"
1
ENLARGED NEW CONSTRUCTION PLAN
TOILET ACCESSORY
LEGEND
FINISH LEGEND
AutoCAD SHX Text
14
AutoCAD SHX Text
11
AutoCAD SHX Text
12
AutoCAD SHX Text
15
AutoCAD SHX Text
15
AutoCAD SHX Text
17
AutoCAD SHX Text
16
AutoCAD SHX Text
16
AutoCAD SHX Text
18
AutoCAD SHX Text
19
AutoCAD SHX Text
14
AutoCAD SHX Text
12
AutoCAD SHX Text
17
AutoCAD SHX Text
18
AutoCAD SHX Text
TA12
AutoCAD SHX Text
TA08
AutoCAD SHX Text
TA11
AutoCAD SHX Text
TA01
AutoCAD SHX Text
TA02
AutoCAD SHX Text
TA03
AutoCAD SHX Text
TA10 (TYP)
AutoCAD SHX Text
TA04
AutoCAD SHX Text
TA09
AutoCAD SHX Text
TA09
AutoCAD SHX Text
13
AutoCAD SHX Text
13
AutoCAD SHX Text
TA11
AutoCAD SHX Text
TA08
AutoCAD SHX Text
TA12
AutoCAD SHX Text
TA03
AutoCAD SHX Text
TA01
AutoCAD SHX Text
TA02
AutoCAD SHX Text
TA10 (TYP)
AutoCAD SHX Text
TA06
AutoCAD SHX Text
TA05 (TYP)
AutoCAD SHX Text
TA06 (TYP)
AutoCAD SHX Text
TA09
AutoCAD SHX Text
TA04
AutoCAD SHX Text
TA09
AutoCAD SHX Text
22
AutoCAD SHX Text
22
AutoCAD SHX Text
20a
AutoCAD SHX Text
20c
AutoCAD SHX Text
20b
AutoCAD SHX Text
20b
AutoCAD SHX Text
20a
AutoCAD SHX Text
2
AutoCAD SHX Text
21
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
P2
AutoCAD SHX Text
P2,CT1-3
AutoCAD SHX Text
PT1
AutoCAD SHX Text
PT1
AutoCAD SHX Text
P2
AutoCAD SHX Text
P2,CT1-3
AutoCAD SHX Text
PT1
AutoCAD SHX Text
PT1
AutoCAD SHX Text
PL1
AutoCAD SHX Text
PL1
AutoCAD SHX Text
PL1
AutoCAD SHX Text
PL1
AutoCAD SHX Text
1
AutoCAD SHX Text
1
AutoCAD SHX Text
I G N
AutoCAD SHX Text
A. REFER TO GENERAL CONSTRUCTION NOTES ON SHEET G0.01. REFER TO GENERAL CONSTRUCTION NOTES ON SHEET G0.01. B. REFER TO ENLARGED PLAN FOR TOILET FIXTURE, TOILET REFER TO ENLARGED PLAN FOR TOILET FIXTURE, TOILET ACCESSORIES, AND PARTITION DEMOLITION. C. CONTRACTOR SHALL VERIFY THAT ACCESS PANELS ARE INSTALLED CONTRACTOR SHALL VERIFY THAT ACCESS PANELS ARE INSTALLED IN A NON-ACCESSIBLE TYPE CEILING WHERE SERVICE OR ADJUSTMENTS TO MECHANICAL , PLUMBING, OR ELECTRICAL ITEMS MAY BE REQUIRED. ACCESS PANELS SHALL BE THE FIRE RATED TYPE EQUAL TO THE RATING OF THE WALL OR CEILING IN WHICH THEY OCCUR. D. SCHEDULE ALL DEMOLITION AND NEW CONSTRUCTION WITH THE SCHEDULE ALL DEMOLITION AND NEW CONSTRUCTION WITH THE OWNER E. REMOVE EXISTING FLOOR AND WALL FINISH, NOT LIMITED TO REMOVE EXISTING FLOOR AND WALL FINISH, NOT LIMITED TO CERAMIC TILE, WALL BASE, WITHIN SCOPE OF WORK IN TOILETS. F. REFER TO ENLARGED FINISH PLANS FOR INTERIOR FINISH MATERIAL REFER TO ENLARGED FINISH PLANS FOR INTERIOR FINISH MATERIAL DESIGNATIONS IN PLAN 02/A2.01. G. REFER TO ENLARGED NEW CONSTRUCTION PLAN FOR ANNOTATION REFER TO ENLARGED NEW CONSTRUCTION PLAN FOR ANNOTATION RE: 01/A2.02.
AutoCAD SHX Text
THROUGH NOT USED PATCH AND REPAIR HOLE IN EXISTING GYP BOARD WHERE MEN'S ROOM DOOR CLOSER HAS DAMAGED WALL. INSTALL NEW GYPBOARD, PAINT, CERAMIC TILE, PORCELAIN TILE, AND PORCELAIN TILE WALL BASE AS SHOWN ON ELEVATIONS. PROVIDE UNUSED MATERIALS NOT INSTALLED TO DCCCD. PATCH AND PREPARE EXISTING BRICK WALL TO MAKE READY FOR NEW PAINT AND TILE BASE. INSTALL NEW LAMINATE COUNTERTOP AND BACKSPLASH AS SHOWN ON ELEVATION AND DETAIL. ALTERNATE NO. 1: CONTRACTOR TO INCLUDE IN ITS BID AMOUNT : CONTRACTOR TO INCLUDE IN ITS BID AMOUNT THE COST TO REFINISH EXISTING RESTROOM DOORS. ADD KICKPLATE ON ENTRY SIDE. REMOVE AND CLEAN EXISTING HARDWARE. REPLACE WITH REFINISHED DOOR AND EXISTING HARDWARE. AS INDICATED ON DRAWINGS. INCLUDE REPAIR AND REPAINTING OF FRAME AS NECESSARY. INSTALL NEW TOILET PARTITIONS. REFER TO PROJECT MANUAL FOR SPECIFICATION. INSTALL TOILET ACCESSORIES, INCLUDING BUT NOT LIMITED TO TOILET PAPER HOLDER, MIRROR, PAPER TOWER DISPENSER, SOAP DISPENSER, TRASH RECEPTACLES. FLUSH CLEAN OUT WITH WALL AND PROVIDE NEW BRASS CAP. REFER TO MPE DRAWINGS. PROVIDE NEW CLEAN OUT IN WOMEN'S RESTROOM BELOW COUNTERTOP. REFER TO MPE PLANS. INSTALL NEW PLUMBING FIXTURE, FITTINGS, ACCESSORIES, WALL ANCHORS, REPLACEMENT PIPES AND INSULATE ALL EXPOSED PIPING UNDER LAVATORIES / SINKS WITH A WHITE, FITTED ANTI-MICROBIAL PIPE COVER. COVER SHALL BE DESIGNED TO ALLOW ACCESS TO THE STOP VALVE. REFER TO MPE DRAWINGS FOR PLUMBING SCHEDULE.: 20a - WATER CLOSET: 20b - SINK 20c - URINAL: REMOVE EXISTING AND HOLD FOR REINSTALLATION INSTALL NEW HOT WATER HEATER AND ASSOCIATED PIPING IN WAREHOUSE SPACE. REFER TO MPE DRAWINGS. REPLACE EXISTING MARBLE THRESHOLD.
AutoCAD SHX Text
ACT
AutoCAD SHX Text
VWC
AutoCAD SHX Text
RB
AutoCAD SHX Text
VCT
AutoCAD SHX Text
PL1
AutoCAD SHX Text
PL2
AutoCAD SHX Text
1
AutoCAD SHX Text
11
AutoCAD SHX Text
12
AutoCAD SHX Text
13
AutoCAD SHX Text
14
AutoCAD SHX Text
15
AutoCAD SHX Text
16
AutoCAD SHX Text
17
AutoCAD SHX Text
18
AutoCAD SHX Text
19
AutoCAD SHX Text
20
AutoCAD SHX Text
21
AutoCAD SHX Text
22
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
NORTH
AutoCAD SHX Text
TA01
AutoCAD SHX Text
PAPER TOWEL DISPENSER: BOBRICK B-3949
AutoCAD SHX Text
TA01
AutoCAD SHX Text
HAND DRYER: BOBRICK B-7128
AutoCAD SHX Text
TA02
AutoCAD SHX Text
WASTE RECEPTACLE: BOBRICK-279
AutoCAD SHX Text
TA03
AutoCAD SHX Text
TOILET TISSUE DISPENSER: BOBRICK B-2740
AutoCAD SHX Text
TA04
AutoCAD SHX Text
SANITARY NAPKIN DISPOSAL: BOBRICK B-270
AutoCAD SHX Text
TA05
AutoCAD SHX Text
SEAT COVER DISPENSER: BOBRICK B-221
AutoCAD SHX Text
TA06
AutoCAD SHX Text
NOT USED
AutoCAD SHX Text
TA07
AutoCAD SHX Text
SOAP DISPENSER: PROVIDED BY OTHERS
AutoCAD SHX Text
TA08
AutoCAD SHX Text
GRAB BARS: BOBRICK B-6806
AutoCAD SHX Text
TA09
AutoCAD SHX Text
COAT HOOK W/BUMPER: BOBRICK B-212
AutoCAD SHX Text
TA10
AutoCAD SHX Text
MIRROR FRAMED: AMERICAN SPECIALTIES #0620
AutoCAD SHX Text
TA11
AutoCAD SHX Text
TOUCHLESS TOWEL DISPENSER: REMOVE EXISTING, HOLD & REINSTALL
