Date: 30 April 2020 - 01-21... · 2021. 1. 22. · The key design assumption is that the steelwork...

Job No. 20-01 Date: 30 April 2020

DWG Engineering

12 Arundel St

Kensington, 6151

ABN: 25 340 335 240

TRACHMACH WA.

Attention: Francis Kidman

Dear Sir,

RE: CHAMBERLAIN STRUCTURAL REVIEW

DWG Engineering has been approached by Francis Kidman to structurally certify the design of

the sub-structure and footings supporting a 5x scale model of a Chamberlain tractor, as

depicted in the image below.

This letter is to certify that this practice has carried out the design verification of the structural

elements depicted on the attached drawings.

The key design assumption is that the steelwork fabrication will be managed by experienced

and competent people who are familiar with structural steel fabrication. DWG Engineering also

request to visit the site to review the completed unit once constructed.

Job No. 20-01 Date: 30 April 2020

DWG Engineering

12 Arundel St

Kensington, 6151

ABN: 25 340 335 240

We have carried out the structural design in accordance with the provisions of relevant

Australian Standards and generally accepted engineering principles, including but not limited

to:

AS/NZS 1170.0 2002

AS 4100 1998

AS 3600 2018

Should you require any further comment, please don’t hesitate to contact me.

Yours faithfully

DWG ENGINEERING

Dane Glenn Structural Engineer

B.Eng (Civil)

MIE Aust. No. 4360361

TRACMACH

21/1/2021

SPECIFICATION FOR SUPPLY OF MATERIALS, SURFACE PREPARATION AND APPLICATION COATING SYSTEM TO CHAMBERLAIN 40K - 5X SCALE TRACTOR

SCOPE

This specification covers the requirements for the supply of materials, surface preparation and application of coating systems for the surface protection of the Chamberlain 40K tractor. RESPONSIBILITY

The contractor is responsible for assurance that the materials, components, workmanship, placement, testing and examination complies with the manufacturers’ specifications. REFERENCES

The publications below form part of this specification. Each publication shall be the latest revision and addendum in effect on the date this specification is issued unless noted otherwise. Australian/New Zealand Standards AS 1580 Paints and related materials – Methods of test AS 1627 Metal finishing – Preparation and pre-treatment of surfaces AS/NZS 2310 Glossary of paint and painting terms AS 2331 Methods of test for metallic and related coatings AS 2700 Colour standards for general purposes AS 3894 Site testing of protective coatings AS/NZS 2312 Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings. APPLICATION

Surface Preparation: Abrasive blast cleaned as per AS 1627.4, Class 2½ profile 50-60um. Primer: Apply as soon as possible after blast cleaning, no later than 4 hours. One coat to DFT 75um. Top Coat: After allotted primer drying time, (as specified on container) one coat of latex-based paint to DFT 150um making a total of DFT 225um minimum. Colour 06713 2K CHAMBERLAIN ORANGE. Any deviation from the above shall be by agreement with TRACMACK.

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3

AutoCAD SHX TextDRAWN

AutoCAD SHX TextCHECKED

AutoCAD SHX TextAPPROVED

AutoCAD SHX TextDWG No.

AutoCAD SHX TextFRANK KIDMAN

AutoCAD SHX Text6/11/2019

AutoCAD SHX TextTRACMACH CHAMBERLAIN 40K

AutoCAD SHX Text1 TRACTOR ASSEMBLY



AutoCAD SHX TextTHE ASSEMBLY SHOWN CONSISTS OF THE FOLLOWING DRAWINGS. DWG 2 AIR CLEANER ASSEMBLY DWG 3 RADIATOR GRILL DWG 4 HEAD LIGHT BRACKET DWG 5 ENGINE COVER DWG 6 REAR TYRE SHELL DWG 7 REAR TYRE LUG DWG 8 INSTRUMENT PANEL DWG 9 FRONT AXLE DWG 10 REAR TYRE RIM DWG 11 REAR WHEEL BOLTS AND NUTS DWG 12 REAR WHEEL HUB DISC DWG 13 REAR SPLIT RIM FALSE BOLTS AND NUTS DWG 14 REAR WHEEL CENTRAL HUB DWG 15 TRACTOR SUPPORT FRAME DWG 15.1 TRACTOR SUPPORT FRAME PLATES DWG 15.2 BEAMS AND COLUMNS DWG 17 REAR BRAKES DWG 18 REAR GEARBOX DOOR DWG 19 STEERING WHEEL GEARBOX (BOX ONLY) DWG 21 PTO AND SEAT MOUNT DWG 22 SEAT DWG 23 TOP TANK DWG 24 RADIATOR COWLING DWG 25 GOVERNOR HOUSING DWG 26 GEARBOX SIDE PLATES DWG 27 HEAD AND WORKING LIGHTS DWG 28 FLOOR PLATES DWG 29 DRAWBAR ASSEMBLY DWG 30 RADIATOR DWG 31 MUFFLER DWG 32 MUD GUARDS DWG 33 HAND BRAKE AND CLUTCH LEVER DWG 34 FRONT TYRE DWG 35 FRONT WHEEL DWG 36 FRONT AXLE DWG 37 DISTRIBUTOR COVER DWG 39 FRONT ENGINE TO RADIATOR CASTING DWG 40 NAME PLATES DWG 41 ENGINE COVER REAR MOUNTING DWG 42 CYLINDER HEAD DWG 43 CYLINDER BLOCK DWG 44 BOTTOM CW PIPES DWG 45 TOP CW PIPES DWG 46 EXHAUST PIPES DWG 47 INLET PIPES DWG 48 INLET EXHAUST MANIFOLD DWG 49 RADIATOR BOTTOM PANEL DWG 50 REAR AXLE HOUSING DWG 51 STEERING LINKAGES DWG 52 FAN DWG 53 OIL FILTER DWG 54 GEARBOX UPPER PLATES DWG 55 GEARBOX UPPER PLATES AND STICKS DWG 56 GEARBOX SUMP PLATES DWG 57 CLUTCH HOUSING DWG 58 ENGINE PLATES DWG 59 ENGINE SUMP PLATES DWG 60 STARTER MOTOR DWG 61 GENERATOR DWG 62 CRANK HANDLE DWG 63 DRAWBAR ANCHOR DWG 64 CARBURETOR AND INLET PIPE DWG 65 THROTTLE DWG 66 FRONT SUPPORT BRACKET

AutoCAD SHX TextJOHN PIAVANINI


AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text1.1 ENGINE AND GEARBOX ASSEMBLY



AutoCAD SHX TextTHE ASSEMBLY SHOWN CONSISTS OF THE FOLLOWING DRAWINGS. DWG 17 REAR BRAKES DWG 18 REAR GEARBOX DOOR DWG 19 STEERING WHEEL GEARBOX (BOX ONLY) DWG 25 GOVERNOR HOUSING DWG 26 GEARBOX SIDE PLATES DWG 29 DRAWBAR ASSEMBLY DWG 37 DISTRIBUTOR COVER DWG 39 FRONT ENGINE TO RADIATOR CASTING DWG 43 CYLINDER BLOCK DWG 44 BOTTOM CW PIPES DWG 53 OIL FILTER DWG 54 GEARBOX UPPER PLATES DWG 55 GEARBOX UPPER PLATES AND STICKS DWG 56 GEARBOX SUMP PLATES DWG 57 CLUTCH HOUSING DWG 58 ENGINE PLATES DWG 59 ENGINE SUMP PLATES DWG 60 STARTER MOTOR DWG 63 DRAWBAR ANCHOR DWG 66 FRONT SUPPORT BRACKET

AutoCAD SHX TextDOOR SIZE SHOWN IS 5000 WIDE x 5000 HIGH. OTHER PARTS SUCH AS THE SEAT, CYLINDER HEADS, GEAR STICKS, FAN etc MUST BE FITTED OUTSIDE.



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text1.2 CONSTRUCTION





AutoCAD SHX TextTASK LIST 1. POUR FOOTINGS TO DIMENSIONS SHOWN IN DRAWING 15. POUR FOOTINGS TO DIMENSIONS SHOWN IN DRAWING 15. 2. BOLT COLUMNS IN PLACE. BOLT COLUMNS IN PLACE. 3. FIT FRONT WHEEL AND AXLE ASSEMBLY TO FRONT SUPPORT COLUMNS FIT FRONT WHEEL AND AXLE ASSEMBLY TO FRONT SUPPORT COLUMNS 4. ASSEMBLE ENGINE AND GEARBOX COMPLETE WITH SUPPORT BEAMS INSIDE AS SHOWN. NOTE, ASSEMBLE ENGINE AND GEARBOX COMPLETE WITH SUPPORT BEAMS INSIDE AS SHOWN. NOTE, STEERING WHEEL AND CLUTCH LINK TO BE FITTED LATER.. 5. LOWER ENGINE AND GEARBOX ASSEMBLY INTO POSITION., BOLT REAR CROSS BEAM TO REAR LOWER ENGINE AND GEARBOX ASSEMBLY INTO POSITION., BOLT REAR CROSS BEAM TO REAR COLUMNS. BOLT INTERNAL AND WELD BRACKETS SHOWN IN DRAWING 66 TO FALSE LEAVE SPRING BEAM AT THE FRONT. 6. FIT REAR WHEELS. FIT REAR WHEELS. 7. FIT MUD GUARDS COMPLETE WITH FLOOR PLATES. FIT MUD GUARDS COMPLETE WITH FLOOR PLATES. 8. FIT STEERING WHEEL AND CLUTCH LINK THROUGH FLOOR PLATES. FIT STEERING WHEEL AND CLUTCH LINK THROUGH FLOOR PLATES. 9. FIT ENGINE COVER ASSEMBLY AND BOLT UP. FIT ENGINE COVER ASSEMBLY AND BOLT UP. 10. FIT AIR CLEANER ASSEMBLY. FIT AIR CLEANER ASSEMBLY. 11. LOWER MUFFLER INTO POSITION.LOWER MUFFLER INTO POSITION.

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3





AutoCAD SHX TextASSEMBLY DIMENSIONS

AutoCAD SHX TextFILTER HOUSING 3mm MS PLATE ROLL TO 1250 OUTSIDE DIAMETER AND FULLY WELD SEAM 207.5 kg

AutoCAD SHX TextPREFILTER HOUSING 3mm MS PLATE ROLL TO 825 OUTSIDE DIAMETER AND FULLY WELD SEAM

AutoCAD SHX TextFILTER INLET TUBE 14" STD WALL BLACK PIPE 244.2 kg

AutoCAD SHX TextPAINT SKY BLUE

AutoCAD SHX TextFILTER MOUNTING BRACKET - 5mm MS PLATE BEND 90 AT DASHED LINES 76.5 kg CAUTION: BEND AS SHOWN IN PICTURE ABOVE

AutoCAD SHX Text3mm PLATE 28.9 kg FILTER BOTTOM

AutoCAD SHX Text3mm PLATE 26.5 kg FILTER TOP

AutoCAD SHX Text3mm PLATE

AutoCAD SHX TextINSPECTION PORT FRAME PLATE - 3mm 1.4 kg

AutoCAD SHX Text3mm PLATE

AutoCAD SHX TextPREFILTER BOTTOM - 5mm PLATE 13.3 kg

AutoCAD SHX TextPRE-FILTER BRACE 2" STD WALL BLACK PIPE. 4 REQ'D 1.6 kg

AutoCAD SHX TextINLET PIPE BRACE PLATES. 5mm MS PLATE 8 REQ'D 20.8 kg

AutoCAD SHX TextFILTER SUPPORT PLATE. 10mm MS PLATE 4 REQ'D 8.0 kg

AutoCAD SHX TextNOTES 1. GRIND ALL EXTERNAL WELDS TO BLEND. GRIND ALL EXTERNAL WELDS TO BLEND. 2. WELD AROUND ALL CONNECTIONS. WELD AROUND ALL CONNECTIONS.

AutoCAD SHX TextHOLE CENTERS

AutoCAD SHX TextPREFILTER INSPECTION PORT 3mm MS PLATE 2.5 kg ROLL TO 365 OUTSIDE DIAMETER AND FULLY WELD SEAM

AutoCAD SHX TextPREFILTER BRACE

AutoCAD SHX TextMOUNTING BRACKET BRACE PLATES. 5mm MS PLATE 2 REQ'D 11.7 kg




AutoCAD SHX Text2 AIR FILTER HOUSING ASSEMBLY

AutoCAD SHX TextCUT PIPE IN HALF LENGTH WAYS AS SHOWN

AutoCAD SHX TextINLET PIPE BRACE PLATES

AutoCAD SHX TextFILTER SUPPORT PLATE

AutoCAD SHX TextPREFILTER TOP PLATE 12.6 kg

AutoCAD SHX TextDUST INSPECTION PORT

AutoCAD SHX TextFILTER INLET TUBE

AutoCAD SHX TextHOLE FOR CARBURETOR INLET PIPE

AutoCAD SHX TextIMITATION GLASS TO BE WELDED TO FRAME PLATE 1.2 kg



AutoCAD SHX TextTOTAL WEIGHT = 642.5 kg

AutoCAD SHX TextCUT TWO REINFORCEMENT GUSSETS

AutoCAD SHX TextWELD IN GUSSETS TO TOP ONLY



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text3 RADIATOR GRILL

AutoCAD SHX TextWELD BOTH SIDES GRIND FLAT THIS SIDE

AutoCAD SHX TextMATERIAL : 5mm MILD STEEL PLATE

AutoCAD SHX TextOUTSIDE DIMENSION

AutoCAD SHX TextGRILL BENDING DETAILS

AutoCAD SHX TextDEVELOPMENT OF GRILL



AutoCAD SHX Text437 kg




AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text4 HEADLIGHT MOUNTING BRACKET

AutoCAD SHX TextBUTT WELD THEN GRIND FLAT ON OUTSIDE



AutoCAD SHX TextBEND TO 50mm RADIUS

AutoCAD SHX TextBEND TO 40mm RADIUS

AutoCAD SHX TextBRACKET EDGE TREATMENT - TOP EDGES 5mm MS PLATE 4 REQ'D

AutoCAD SHX TextBRACKET EDGE TREATMENT - BOTTOM 5mm MS PLATE 2 REQ'D

AutoCAD SHX TextBRACKET FRONT SIDE PLATE ROLL TO 160 OUTSIDE RADIUS 5mm MS PLATE 2 REQ'D

AutoCAD SHX TextBRACKET FACE PLATE 5mm MS PLATE 2 REQ'D

AutoCAD SHX TextBRACKET TOP PLATE 5mm MS PLATE 2 REQ'D

AutoCAD SHX TextBRACKET EDGE TREATMENT ASSEMBLY

AutoCAD SHX TextBRACKET SIDE PLATES 5mm MS PLATE 4 REQ'D

AutoCAD SHX TextLOCATION OF TOP AND SIDE PLATES

AutoCAD SHX TextWELD BRACKET TO SIDE OF RADIATOR AS SHOWN IN DWG 30



AutoCAD SHX TextWEIGHT (ONE) = 27.3 kg WEIGHT (TWO) = 54.6 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text5 ENGINE COVER

AutoCAD SHX TextSIDE STRIPS MATERIAL: 5mm MS PLATE 2 OF EACH TYPE REQ'D

AutoCAD SHX TextLOCATION OF SIDE STRIPS WELD 25, LEAVE 200 FILL PERIMETER WITH SIKAFLEX AFTER BLASTING

AutoCAD SHX TextENGINE COVER CORNER PLATE. MATERIAL: 5mm MS PLATE. 2 REQ'D. ROLL TO 350 OUTSIDE RADIUS TRIM END AFTER WELDING TO PROFILE WITH OTHER PANELS.

AutoCAD SHX TextENGINE COVER SIDE PLATES MATERIAL: 5mm MS PLATE. 2 REQ'D.

AutoCAD SHX TextTOP ENGINE COVER PLATES MATERIAL: 5mm MS PLATE. ROLL TO 10515 RADIUS

AutoCAD SHX TextBUTT WELD

AutoCAD SHX TextINSTRUMENT PLATE DEVELOPMENT MATERIAL: 5mm MS PLATE. BEND 16 DEGREES ALONG DASHED LINE. 1 REQ'D

AutoCAD SHX TextBEND 16 DEGREES ALONG LINE

AutoCAD SHX TextINSTRUMENT PLATE

AutoCAD SHX TextRUNNING HOUR GAUGE PLATE MATERIAL - 5mm MS PLATE WELD TO INSTRUMENT PLATE

AutoCAD SHX TextRUNNING HOUR GAUGE SURROUND MATERIAL - 5mm PLATE WELD TO GAUGE PLATE AT LOCATION SHOWN

AutoCAD SHX TextBEND 16 DEGREES

AutoCAD SHX TextWELD INSTRUMENT GAUGE HOUSING TO PLATE BEFORE PAINTING

AutoCAD SHX TextCORNER PLATE

AutoCAD SHX TextCORNER PLATE

AutoCAD SHX TextTOP PLATES

AutoCAD SHX TextSIDE PLATE

AutoCAD SHX TextLOCATION OF RUNNING HOURS GAUGE SURROUND

AutoCAD SHX TextSIDE VIEW OF ASSEMBLY

AutoCAD SHX TextFIX WIDTH FIX TO 350 RADIUS FIX WIDTHS OF TOP COVER PLATES FOR NEW RADIUS

AutoCAD SHX TextOUTSIDE

AutoCAD SHX TextTOP VIEW OF ASSEMBLY

AutoCAD SHX TextEND VIEW OF ASSEMBLY

AutoCAD SHX TextWELD ALL PARTS TOGETHER AS SHOWN ABOVE

AutoCAD SHX TextNOTE - ALIGN ALL PANELS WITH RADIATOR BEFORE WELDING



AutoCAD SHX TextWEIGHT OF ENGINE COVER = 2358 kg



AutoCAD SHX TextSEE DRAWING 32.1 FOR BRACKETS TO FIX MUD GUARDS TO ENGINE COVER

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text6 REAR TYRE SHELL 32" x 13 "12"

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextD

AutoCAD SHX TextE

AutoCAD SHX TextF

AutoCAD SHX TextG

AutoCAD SHX TextH

AutoCAD SHX TextI

AutoCAD SHX TextJ

AutoCAD SHX TextK

AutoCAD SHX TextL

AutoCAD SHX TextM

AutoCAD SHX TextN

AutoCAD SHX TextO

AutoCAD SHX TextP

AutoCAD SHX TextQ

AutoCAD SHX TextCUT 32 PLATES TO MAKE TWO SHELLS ETCH BEND LINES BEND AS SHOWN IN TABLE ASSEMBLE TO MAKE HALF TYRES AS SHOWN BELOW REFERENCE DIMENSIONS SHOWN BELOW MATERIAL IS 3mm MS PLATE

AutoCAD SHX TextNOTE WHEN COMPLETED WELD ON TYRE LUGS. WELD TYRE ASSEMBLY TO RIM AS SHOWN ABOVE. TO BE CRANED AND FITTED IN TWO HALVES. HOLE TO BE CUT FOR SUPPORT COLUMN AT THE BOTTOM OF THE TYRE AND RIM AT A LATER STAGE.



AutoCAD SHX TextWEIGHT FOR ONE TYRE = 1935 kg WEIGHT FOR TWO TYRES = 3870 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text7 REAR TYRE LUG

AutoCAD SHX TextNOTES 1. BEND TOP TREAD TO FIT SIDE PLATES AT BEND TOP TREAD TO FIT SIDE PLATES AT LOCATIONS SHOWN. 2. MATERIAL 3mm MILD STEEL PLATE. MATERIAL 3mm MILD STEEL PLATE. 3. TEST FIT TO TYRE BEFORE FULLY TEST FIT TO TYRE BEFORE FULLY WELDING ALL CONNECTIONS. 4. 48 R/H LUGS REQ'D, 48 L/H LUGS REQ'D. 48 R/H LUGS REQ'D, 48 L/H LUGS REQ'D. 5. WELD EACH LUG TO TYRE AT LOCATIONS WELD EACH LUG TO TYRE AT LOCATIONS SHOWN



AutoCAD SHX TextWEIGHT FOR ONE TYRE = 1164 kg WEIGHT FOR TWO TYRES = 2327 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text8 INSTRUMENT PANEL

AutoCAD SHX TextMANUFACTURE LIGHT HOUSING FROM 8" STD WALL PIPE, CAP END WITH 5mm PLATE

AutoCAD SHX TextGAUGE FRAME MATERIAL 5mm PLATE 3 REQ'D WELD ALL ROUND ON THE INSIDE OF THE RING TO THE PANEL AT THE LOCATIONS SHOWN

AutoCAD SHX TextGAUGE PANEL MATERIAL 5mm PLATE 1 REQ'D

AutoCAD SHX TextPANEL SWITCH MATERIAL 1" STD WALL PIPE AND 5mm PLATE 2 REQ'D WELD TO THE INSIDE OF THE PANEL AS SHOWN ABOVE

AutoCAD SHX TextCAP END

AutoCAD SHX Text200 x 5 FLAT BEND AS REQ'D TO FIT INSIDE GAUGE PANEL

AutoCAD SHX TextWELD 25 LEAVE 200 ALL ROUND ON THE INSIDE

AutoCAD SHX TextWELD ALL ROUND

AutoCAD SHX TextPAINT GAUGE BEZEL AND TOGGLE SWITCHS SILVER PAINT GAUGE GLASS SKY BLUE.

AutoCAD SHX TextPANEL BOTTOM PLATE WITH GUSSET MATERIAL - 10mm MS

AutoCAD SHX TextWELD PANEL BOTTOM PLATE IN POSITION SHOWN

AutoCAD SHX TextGAUGE PANEL



AutoCAD SHX TextWEIGHT = 24.6 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text9 FRONT AXLE BEAM

AutoCAD SHX TextAXLE BEAM WEB MATERIAL - 8mm MS PLATE 1 REQ'D

AutoCAD SHX TextUPPER AXLE BEAM FLANGE DEVELOPMENT BEND AT LOCATIONS SHOWN TO FIT BEAM WEB MATERIAL - 10mm MS PLATE 1 REQ'D

AutoCAD SHX TextAXLE BEAM SIDE INFILL FITS INSIDE THE FLANGES WITH A FLUSH FACE MATERIAL - 5mm MS PLATE 2 OF EACH TYPE REQ'D

AutoCAD SHX TextLOWER AXLE BEAM FLANGE DEVELOPMENT BEND AT LOCATIONS SHOWN TO FIT BEAM WEB MATERIAL - 10mm MS PLATE 1 REQ'D

AutoCAD SHX TextUPPER INNER BEAM FLANGE DEVELOPMENT BEND AT LOCATIONS SHOWN TO FIT SIDE INFILL - CUT ENDS AS REQUIRED TO FIT WEB STIFFENER PLATE MATERIAL - 5mm PLATE 2 REQ'D

AutoCAD SHX TextLOWER INNER BEAM FLANGE DEVELOPMENT BEND AT LOCATIONS SHOWN TO FIT SIDE INFILL CUT ENDS AS REQUIRED TO FIT WEB STIFFENER PLATE MATERIAL - 5mm PLATE 2 REQ'D

AutoCAD SHX TextEND VIEW

AutoCAD SHX TextTOP VIEW

AutoCAD SHX TextFRONT VIEW

AutoCAD SHX TextBEARING HOUSING DEVELOPMENT ROLL TO 740 OUTSIDE DIAMETER MATERIAL 10mm MS PLATE 2 REQ'D

AutoCAD SHX TextBEARING HOUSING END PLATE MATERAIL - 10mm MS PLATE 2 REQ'D

AutoCAD SHX TextKING PIN TOP PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextKING PIN BOTTOM PLATE MATERIAL - 10mm MS PLATE 2 REQ'D

AutoCAD SHX TextWEB PLATE - BEND 90 DEGREES ALONG DASHED LINE 10mm OUTSIDE RADIUS BEND. MATERIAL - 5mm MS PLATE 4 REQ'D

AutoCAD SHX TextBEARING HOUSING

AutoCAD SHX TextKING PIN MATERIAL - 323.9 x 6.4 WALL CHS 2 REQ'D

AutoCAD SHX TextWEB PLATE

AutoCAD SHX TextBEAM SIDE INFILL

AutoCAD SHX TextKING PIN

AutoCAD SHX TextKING PIN BOTTOM PLATE

AutoCAD SHX TextBEARING HOUSING END PLATE

AutoCAD SHX TextKING PIN TOP PLATE

AutoCAD SHX TextUPPER BEAM FLANGE

AutoCAD SHX TextLOWER BEAM FLANGE

AutoCAD SHX TextUPPER INNER BEAM FLANGE

AutoCAD SHX TextLOWER INNER BEAM FLANGE

AutoCAD SHX TextWHEEL TO BE WELDED CENTRALLY TO THIS FACE

AutoCAD SHX TextUPPER

AutoCAD SHX TextLOWER

AutoCAD SHX Text"A" FRAME AND SPRING MOUNTS WELDED TO THIS FACE



AutoCAD SHX TextWEIGHT = 1051 kg

AutoCAD SHX TextBEAM WEB STIFFENER PLATE MATERIAL - 10mm MS PLATE 4 REQ'D WELD ALL ROUND TO WEB AND FLANGES.

AutoCAD SHX TextINSIDE DIMENSION



AutoCAD SHX TextSTIFFENER PLATE INSIDE, BOTH ENDS

AutoCAD SHX TextWHEEL REMOVED TO SHOW DETAIL

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text10 REAR TYRE RIM

AutoCAD SHX Text4" LONG RADIUS ELBOW

AutoCAD SHX TextRIM LIFTING EYE MANUFACTURE FROM 4" PIPE AND FITTINGS 4 REQ'D

AutoCAD SHX TextWELD ALL ROUND LIFTING EYE TO FACE AT LOCATION SHOWN SPECIAL NOTE---- OTHER EYE TO BE PLACED 180 DEGREES ON OPPOSITE RIM.

AutoCAD SHX TextPAINT INNER SECTION OF RIM BEFORE FITTING TYRE.

AutoCAD SHX TextROLL 4" STD WALL PIPE TO 4405 OUTSIDE DIAMETER

AutoCAD SHX TextRIM CONE SECTION 8 REQ'D TO MAKE 2 RIMS MATERIAL- 3mm MS PLATE CONE ROLL TO INSIDE RADIUS 1748

AutoCAD SHX TextRIM DISC PLATE 4 REQ'D TO MAKE 2 RIMS MATERIAL - 5mm MS PLATE

AutoCAD SHX TextHALF RIM SECTION SHOWN 4 REQ'D TO MAKE 2 RIMS NOTE LOCATIONS OF LIFTING EYES (OPPOSITE EACH OTHER ON EACH RIM)

AutoCAD SHX TextOUTER RIM HALF SECTION 4 REQ'D TO MAKE 2 RIMS MATERIAL - 3mm MS PLATE 1600 WIDE x 6560 LONG ROLL TO 4176 OUTSIDE DIAMETER

AutoCAD SHX TextRIM CONE



AutoCAD SHX TextWEIGHT TWO RIMS = 3126 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text11 REAR WHEEL FALSE BOLTS AND NUT

AutoCAD SHX TextASSEMBLY DETAILS FOR FALSE HUB BOLT HEADS MATERIAL - 5mm STEEL PLATE . 12 REQ'D, 6 FOR EACH WHEEL

AutoCAD SHX TextASSEMBLY DETAILS FOR CENTRE WHEEL NUT MATERIAL - 3mm STEEL PLATE 2 REQ'D, ONE FOR EACH WHEEL.

AutoCAD SHX TextHEXAGON CUTTING DRAWING FOR NUT TOTAL 2 REQ'D - 3mm MS PLATE

AutoCAD SHX TextHEXAGON SIDES CUTTING DRAWING TOTAL 6 REQ'D - 3mm MS PLATE

AutoCAD SHX TextWELD ALL ROUND GRIND FLAT

AutoCAD SHX TextWELD AND GRIND FLAT



AutoCAD SHX TextHEXAGON CUTTING DRAWING FOR NUT 12 REQ'D - 5mm MS PLATE

AutoCAD SHX TextHEXAGON SIDES CUTTING DRAWING TOTAL 36 REQ'D - 5mm MS PLATE

AutoCAD SHX TextNOTES SEE DRAWING 14 FOR LOCATION OF FALSE BOLTS AND NUT. WELD 6 FALSE HUB BOLTS EQUALLY SPACED AS SHOWN ON 760mm PITCH CIRCLE DIAMETER. WELD 25mm EACH SIDE OF HEXAGON APEX. RANDOM ROTATION FOR AUTHENTICITY. CENTRALLY LOCATE LARGE NUT AND WELD 25mm EACH SIDE OF HEXAGON.

AutoCAD SHX TextCUT TO INDICATE AXLE



AutoCAD SHX TextTOTAL WEIGHT ALL ITEMS = 55.7 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text12 REAR WHEEL HUB DISC

AutoCAD SHX Text10" (273mm OD PIPE) STANDARD WALL 130mm LONG 8 REQ'D PER WHEEL TOTAL 16

AutoCAD SHX Text75 x 10 FLAT ROLL TO 3000 OUTSIDE DIAMETER PLACE ON TOP OF DISC AND WELD ALL ROUND THIS SIDE

AutoCAD SHX TextWELD ALL ROUND THIS SIDE

AutoCAD SHX TextCUT 2 DISC PLATES MATERIAL - 10mm MS PLATE

AutoCAD SHX TextWHEEL RIM MOUNTING PLATES MATERIAL - 10mm MS PLATE 20 REQ'D

AutoCAD SHX TextRIM AND TYRE JOIN

AutoCAD SHX TextRIM AND TYRE JOIN LINE

AutoCAD SHX TextNOTES REGARDING COMPLETE REAR TYRE ASSEMBLY 1. ASSEMBLE RIM AND TYRE AND PLACE FACE DOWN ON FLAT SURFACE ASSEMBLE RIM AND TYRE AND PLACE FACE DOWN ON FLAT SURFACE 2. CENTRALIZE WHEEL DISC TO RIM HALVES.. CENTRALIZE WHEEL DISC TO RIM HALVES.. 3. BOLT RIM MOUNTING PLATES TO RIM HALVES. BOLT RIM MOUNTING PLATES TO RIM HALVES. 4. WELD RIM MOUNTING PLATES TO DISC WELD RIM MOUNTING PLATES TO DISC 5. WELD LARGE FALSE ASSEMBLY OVER M48 NUTS (DRAWING 11) WELD LARGE FALSE ASSEMBLY OVER M48 NUTS (DRAWING 11) 6. REFERENCE MARK PARTS FOR SITE ASSEMBLY. REFERENCE MARK PARTS FOR SITE ASSEMBLY. 7. DISASSEMBLE FOR TRANSPORT TO SITEDISASSEMBLE FOR TRANSPORT TO SITE

AutoCAD SHX TextSEE NOTES LEAVE RIM MOUNTING PLATES LOOSE

AutoCAD SHX Text6 x M48 NUTS TOTAL 12 NUTS CENTRALIZE NUT OVER HOLE AND BOLT FLAT. THEN WELD ALL ROUND . TEST BOLT FOR FREE ROTATION AFTER WELDING. WELD REAR WHEEL CENTRAL HUB (DRAWING 14) OVER NUTS., SEE PICTURE BELOW.



AutoCAD SHX TextDISC AND RIM WEIGHT = 1270 KG



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text13 REAR SPLIT RIM FALSE BOLTS

AutoCAD SHX TextASSEMBLY DETAILS FOR FALSE SPLIT RIM BOLTS MATERIAL - 5mm STEEL PLATE AND 3" STD WALL PIPE 20 - M24 x 50 LONG BOLTS AND NUTS REQ'D. 20 REQ'D, 10 FOR EACH WHEEL

AutoCAD SHX TextHEXAGON CUTTING DRAWING FOR NUT 20 REQ'D WITH HOLE, KEEP CENTER TO CAP PIPE 8 REQ'D WITHOUT HOLE MATERIAL - 5mm MS PLATE

AutoCAD SHX TextHEXAGON SIDES CUTTING DRAWING BEND 60 DEGREES ALONG DASHED LINE TOTAL 84 REQ'D MATERIAL - 5mm MS PLATE

AutoCAD SHX Text3" PIPE 160 LONG

AutoCAD SHX TextWELD BOLT HEAD ALL ROUND

AutoCAD SHX TextWELD ALL ROUND THEN GRIND FLAT

AutoCAD SHX TextWELD ALL ROUND THEN GRIND FLAT



AutoCAD SHX TextCAP END OF PIPE



AutoCAD SHX TextBOLT ANCHOR PLATE 20 REQ'D MATERIAL - 5mm PLATE

AutoCAD SHX TextM24 x 50 LONG BOLT WITH NUT

AutoCAD SHX TextTOTAL WEIGHT ALL PARTS = 121 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text14 REAR WHEEL CENTRAL HUB

AutoCAD SHX TextBEND TO 508 CONVEX RADIUS


AutoCAD SHX TextBEND TO 62 CONCAVE RADIUS

AutoCAD SHX TextSIDE PLATE BENDING DETAIL MATERIAL - 5mm PLATE 4 REQ'D, 2 FOR EACH REAR WHEEL


AutoCAD SHX TextBEND TO 62 CONCAVE RADIUS

AutoCAD SHX TextWELD ALL ROUND ON THE OUTSIDE AND GRIND FLAT

AutoCAD SHX TextETCH LOCATION OF HEXAGONS

AutoCAD SHX TextFULLY WELD JOIN ON EACH SIDE

AutoCAD SHX TextSEE DRAWING 11 FOR HEXAGON BOLT AND NUT DETAILS



AutoCAD SHX TextMATERIAL - 5mm MS PLATE 2 REQ'D, ONE FOR EACH REAR WHEEL

AutoCAD SHX TextWEIGHT FOR TWO = 97 kg



30/04/2020

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text17 REAR END BRAKE HOUSING

AutoCAD SHX TextINNER BRAKE HOUSING PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextOUTER BRAKE HOUSING PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextBRAKE HOUSING PERIPHERAL PLATE ROLL AS SHOWN TO FIT INSIDE OUTER AND INNER HOUSING PLATES MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextROLL TO 800mm OUTSIDE RADIUS




AutoCAD SHX TextKEEP CENTER DISC

AutoCAD SHX TextKEEP CENTER DISC

AutoCAD SHX TextHOUSING PROTRUSION ROLL TO 440 OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE USE DISC CUT FROM COVER TO CAP 2 REQ'D

AutoCAD SHX TextHOUSING PROTRUSION ROLL TO 565 OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE USE DISC CUT FROM COVER TO CAP 2 REQ'D

AutoCAD SHX TextCAUTION BRAKE HOUSING TO GEARBOX ATTACHMENT TUBE. ONE OF EACH HAND REQ'D, CHECK WHEN ROLLING. ROLL TO 800mm OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextBRAKE HOUSING PERIPHERAL PLATE ROLLING DETAIL

AutoCAD SHX TextLOCATION KEY FOR LOCATING ATTACHMENT TUBE TO GEARBOX

AutoCAD SHX TextNOTE ORIENTATION OF BRAKE HOUSINGS AND HOUSING PROTRUSIONS



AutoCAD SHX TextTOTAL WEIGHT TWO HOUSINGS = 351 kg



AutoCAD SHX TextKEEP DISCS FOR WELDING INTO COVER.

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text18 REAR GEARBOX DOOR

AutoCAD SHX TextGEARBOX REAR PLATE MATERIAL - 5mm MS PLATE ETCH MARK HEXAGONS FOR BOLT HEAD PLACEMENT NOTE 6 NUTS WELDED TO DRAW-BAR PLATE - SEE DRAWING 29

AutoCAD SHX TextGEARBOX REAR PLATE DEVELOPMENT OF CURVED PLATE ROLL TO 1070 INSIDE RADIUS TO FIT ON TOP OF SIDE PLATES MATERIAL - 5mm MS PLATE

AutoCAD SHX TextGEARBOX REAR SIDE PLATE 2 REQ'D MATERIAL - 5mm MS PLATE

AutoCAD SHX TextHEXAGON BOLT HEAD 15 REQ'D MATERIAL - 5mm MS PLATE

AutoCAD SHX TextHEXAGON BOLT SIDE DEVELOPMENT BEND 120 DEGREES ALONG LINES 30 REQ'D MATERIAL - 50 x 5mm FLAT



AutoCAD SHX TextTOTAL WEIGHT DOOR PLUS BOLTS = 261 kg

AutoCAD SHX TextWELD ASSEMBLY ALL ROUND TO GEARBOX PLATES.



AutoCAD SHX TextWELDED TO DRAWBAR PLATE

AutoCAD SHX TextWELDED TO DRAWBAR PLATE

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text19 STEERING WHEEL AND BOX

AutoCAD SHX TextDEVELOPMENT OF CURVED SECTION STEERING GEARBOX ROLL 774mm SECTION TO R275 AS SHOWN LEFT MATERIAL - 5mm MS PLATE

AutoCAD SHX TextSTEERING GEARBOX TOP, BOTTOM AND SIDE PLATES. MATERIAL 5mm MS PLATE

AutoCAD SHX TextSTEERING WHEEL TOP AND BOTTOM HUB PLATES. MATERIAL - 5mm MS PLATE

AutoCAD SHX TextDEVELOPMENT OF STEERING WHEEL SIDE HUB PLATES. 4 REQ'D ROLL TO 475 OUTSIDE DIAMETER. MATERIAL - 5mm MS PLATE

AutoCAD SHX Text2 REQ'D

AutoCAD SHX Text4" STANDARD WALL BLACK PIPE, ROLL TO 2300 OUTSIDE DIAMETER

AutoCAD SHX Text4" STANDARD WALL BLACK PIPE SPOKES 890mm LONG. BLEND END TO STEERING WHEEL AND WELD ALL ROUND.

AutoCAD SHX TextROLLED

AutoCAD SHX TextWELD ALL ROUND ALL CONNECTIONS AND GRIND SMOOTH

AutoCAD SHX TextASSEMBLY

AutoCAD SHX Text8" STD WALL BLACK PIPE

AutoCAD SHX TextHUB TOP PLATE

AutoCAD SHX TextHUB BOTTOM PLATE

AutoCAD SHX TextACQUIRE 200mm OD STEEL HEMISPERE, WELD ALL ROUND TO NUT

AutoCAD SHX TextDEVELOPMENT OF WHEEL NUT TOP AND SIDES. MATERIAL - 3mm MS PLATE

AutoCAD SHX Text3 PIECES REQ'D BEND TO MAKE HEXAGON

AutoCAD SHX TextNOTE WELD STEERING GEARBOX IN PLACE AFTER FLOOR PLATES AND ENGINE COVER WELD THROTTLE ASSEMBLY (DWG 65) TO TOP OF STEERING SHAFT UNDER WHEEL

AutoCAD SHX TextUPPER STEERING SHAFT SUPPORT BRACKET TO BE WELDED TO THE ENGINE COVER MATERIAL - 5mm MS PLATE

AutoCAD SHX TextFACE PLATE 2 REQ'D

AutoCAD SHX TextEDGE PLATE BEND 90 DEGREES 2 REQ'D

AutoCAD SHX TextWELD EDGE TO ENGINE COVER



AutoCAD SHX TextTOTAL WEIGHT = 517 kg



AutoCAD SHX TextNOTE SEE DRAWING 51 FOR DETAILS OF MOUNTING STEERING GEARBOX TO THE SIDE OF THE GEARBOX.. STEERING WHEEL AND SHAFT ASSEMBLY NOT TO BE WELDED TO STEERING GEARBOX.

AutoCAD SHX TextDO NOT WELD TO STEERING GEARBOX

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text21 Power take off and seat mount

AutoCAD SHX TextDEVELOPMENT OF POWER TAKE OFF HOUSING ROLL TO 890 OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextHOUSING END PLATE KEEP CENTER FOR SPLINE COVER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextSPLINE COVER TUBE (490 LONG) ROLL TO 380 OUTSIDE DIAMETER MATERIAL 3mm MS PLATE

AutoCAD SHX TextHAND BRAKE PLATES ALL BENDS 6mm INSIDE RADIUS MATERIAL - 3mm MS PLATE

AutoCAD SHX TextSEAT MOUNTING PLATE ALL BENDS 10mm INSIDE RADIUS MATERIAL - 5mm MS PLATE

AutoCAD SHX TextPTO TOP PLATE ALL BENDS 6mm INSIDE RADIUS MATERIAL - 3mm MS PLATE

AutoCAD SHX TextCROSS TUBE ATTACHMENT PLATES ALL BENDS 6mm INSIDE RADIUS MATERIAL - 3mm MS PLATE

AutoCAD SHX TextCROSS TUBE DEVELOPMENT (1950 LONG) ROLL TO 340mm OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE







AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text22 SEAT

AutoCAD SHX TextDEVELOPMENT OF SEAT BACK MATERIAL - 3mm PLATE

AutoCAD SHX TextSEAT BASE MATERIAL - 5mm PLATE

AutoCAD SHX TextSPECIAL NOTE - THIS RADIUS IS MADE TO FIT THE BACK OF THE SEAT

AutoCAD SHX TextSPECIAL NOTE - THIS RADIUS IS MADE TO FIT THE BACK OF THE SEAT

AutoCAD SHX TextSEAT BACK CUSHION PAINT COLOUR AS SHOWN MATERIAL - 3mm PLATE

AutoCAD SHX TextSEAT CUSHION PAINT COLOUR AS SHOWN MATERIAL - 3mm PLATE

AutoCAD SHX TextSEAT SIDE PANEL 2 REQ'D MATERIAL - 3mm PLATE

AutoCAD SHX TextSEAT CUSHION FRONT CORNER ROLL TO R380 2 REQ'D MATERIAL - 3mm MS PLATE

AutoCAD SHX TextBEND TO R380 BOTH SIDES

AutoCAD SHX TextMOCK SEAT SPRING ROLLTO 300mm OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLOWER DEVELOPMENT OF SEAT BRACKET MATERIAL - 6mm MS PLATE

AutoCAD SHX TextUPPER DEVELOPMENT OF SEAT BRACKET MATERIAL - 6mm MS PLATE

AutoCAD SHX TextLOCATION OF MOCK SPRING

AutoCAD SHX TextBEND TO R60




AutoCAD SHX TextSEAT BRACKET SIDE PLATE, 2 REQ'D TO BE FITTED INSIDE THE TOP AND BOTTOM PLATE - WELD ALL ROUND MATERIAL - 6mm MS PLATE

AutoCAD SHX TextMOCK SPRING COVER PLATE MATERIAL - 3mm MS PLATE



AutoCAD SHX TextSIDE VIEW OF ASSEMBLED SEAT BASE, SEAT BACK AND SIDE PANEL






AutoCAD SHX TextWELD ALL ROUND ALL CONNECTIONS

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text23 RADIATOR TOP TANK

AutoCAD SHX TextFRONT OF RADIATOR TOP TANK BEND FINGERS TO 350 RADIUS THEN ROLL IN OTHER DIRECTION TO CLOSE FINGER TIPS. WELD ASSEMBLY TO RADIATOR GRILL (DWG 3). MATERIAL - 3 mm MS PLATE

AutoCAD SHX TextTOP OF RADIATOR TOP TANK BEND MIDDLE 2937 SECTION TO 10515 RADIUS BEND SIDE 494 SECTIONS TO 350 RADIUS MATERIAL - 5 mm MS PLATE

AutoCAD SHX TextRADIATOR CORNER SEGMENT BEND OR ROLL FINGERS TO 350 RADIUS THEN ROLL IN OTHER DIRECTION TO CLOSE FINGER TIPS. FIT CLOSING SEGMENT AT FINGER TIPS. MIG WELD ALL CONNECTIONS AND GRIND FLAT TO FORM SPHERICAL SHAPE.

AutoCAD SHX TextRADIATOR CORNER SEGMENT LEFT HAND SIDE MATERIAL - 3 mm MS PLATE



AutoCAD SHX TextCORNER CLOSE SEGMENT

AutoCAD SHX TextCORNER CLOSE SEGMENT

AutoCAD SHX TextRADIATOR CORNER SEGMENT RIGHT HAND SIDE MATERIAL - 3 mm MS PLATE



AutoCAD SHX TextWEIGHT = 346.4 KG



AutoCAD SHX TextGRIND ALL EXTERNAL WELDS TO BLEND.

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text24 RADIATOR COWLING

AutoCAD SHX TextBEND ALONG DASHED LINES TO FORM TRANSITION MATERIAL - 3mm MS PLATE FULLY WELD AT MID SECTIONS TO MAKE COMPLETE ASSEMBLY.SHOWN LEFT. WELD SIDES TO RADIATOR SIDE PLATES.

AutoCAD SHX TextDEVELOPMENT OF TRANSITION COWLING







AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text25 Governor housing

AutoCAD SHX TextDEVELOPMENT OF CYLINDRICAL PORTION OF HOUSING MATERIAL - 3mm MS PLATE

AutoCAD SHX TextDEVELOPMENT OF CONICAL PORTION OF HOUSING MATERIAL - 3mm MS PLATE

AutoCAD SHX TextTOP PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextFRONT PLATES MATERIAL - 3mm MS PLATE

AutoCAD SHX TextBACK PLATES MATERIAL - 3mm MS PLATE

AutoCAD SHX TextSIDE PLATES MATERIAL - 3mm MS PLATE

AutoCAD SHX TextBACK CYLINDER PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextUNDER PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextSIDE PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextDEVELOPMENT OF FRONT CYLINDER MATERIAL -3mm MS PLATE

AutoCAD SHX TextFRONT CYLINDER COVER MATERIAL -3mm MS PLATE






AutoCAD SHX TextWELD ALL ROUND ALL CONNECTIONS

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text26 Gearbox side plates

AutoCAD SHX TextGEARBOX LEFT HAND SIDE PLATE BEND ALONG DASHED LINE AS SHOWN. MATERIAL - 5mm MS PLATE NOTE - KEEP RECTANGULAR AND RIGHT HAND CIRCULAR CUT OUTS TO MAKE RAISED PLATES AT SAME LOCATION

AutoCAD SHX TextKEEP





AutoCAD SHX TextGEARBOX RIGHT HAND SIDE PLATE BEND ALONG DASHED LINE AS SHOWN. MATERIAL - 5mm MS PLATE NOTE - KEEP CUT OUTS TO MAKE RAISED PLATES AT SAME LOCATION

AutoCAD SHX TextDIFFERENTIAL COVER PLATE RIM MATERIAL - 100 x 5 FLAT ROLL TO 1055 OUTSIDE DIAMETER 2 REQ'D

AutoCAD SHX TextGEARBOX INSPECTION DOOR RIM ROLL 263 SECTIONS TO 170 OUTSIDE RADIUS MATERIAL - 100 x 5 FLAT 2 REQ'D

AutoCAD SHX TextCLUTCH INSPECTION DOOR EDGES MATERIAL - 50 x 5 FLAT

AutoCAD SHX TextR/H VERTICAL 2 REQ'D

AutoCAD SHX TextR/H AND L/H HORIZONTAL 4 REQ'D

AutoCAD SHX TextL/H VERTICAL 2 REQ'D






AutoCAD SHX TextCLUTCH INSPECTION DOOR

AutoCAD SHX TextGEARBOX INSPECTION DOOR

AutoCAD SHX TextDIFFERENTIAL COVER

AutoCAD SHX TextCLUTCH INSPECTION DOOR

AutoCAD SHX TextDIFFERENTIAL COVER

AutoCAD SHX TextNOTE HINGE GEARBOX DOOR FOR INTERNAL ACCESS. MAKE LOCKABLE

AutoCAD SHX TextBEND


AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text27 HEAD AND WORKING LIGHT

AutoCAD SHX Text8" BLACK PIPE 219 OUTSIDE DIAMETER 8mm WALL.

AutoCAD SHX TextCUT PLOUGH DISC TO FIT INSIDE, FILL CENTER

AutoCAD SHX TextDEVELOPMENT OF HEAD LIGHT MATERIAL - 3mm MS PLATE 6 REQ'D TO MAKE 3 LIGHTS (2 HEAD AND 1 WORKING LIGHT)

AutoCAD SHX TextCENTER FILL DISC FOR REAR OF LIGHT MATERIAL 3mm MS PLATE 3 REQ'D

AutoCAD SHX TextCENTER FILL DISC

AutoCAD SHX TextGUIDE FOR CUTTING 8" PIPE TO CORRECT PROFILE. PRINT HALF OF DRAWING ABOVE ON A3 PAPER TO FULL SCALE WRAP AROUND PIPE TO MARK CUTTING LINE. IF NOT AVAILABLE SCALE FROM DRAWING ABOVE.

AutoCAD SHX Text8" BLACK PIPE 219 OUTSIDE DIAMETER 8mm WALL.

AutoCAD SHX TextTHREE LIGHTS REQ'D WELD TWO ASSEMBLIES TO HEADLIGHT BRACKET. WELD ONE ASSEMBLY TO LEFT HAND REAR MUD GUARD

AutoCAD SHX TextLEFT HAND SIDE HEAD LIGHT ASSEMBLY SHOWN



AutoCAD SHX TextWEIGHT FOR THREE LIGHTS = 122.6 kg

AutoCAD SHX TextWELD ALL CONNECTIONS THEN GRIND EXTERNALLY TO BLEND.



AutoCAD SHX TextNOTE THREE PLOUGH DISCS REQUIRED FOR HEADLIGHT GLASS SIMULATION. MUST BE AT LEAST 770.FILL CENTER HOLE AND GRIND FLAT.

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text28 Floor plates

AutoCAD SHX TextFLOOR PLATES TO BE FULLY WELDED TO MUD GUARDS MATERIAL - 5mm MS PLATE SEE DRAWING 32.1 FOR BRACKETS TO FIX MUD GUARDS TO REAR OF ENGINE COVER


AutoCAD SHX TextADD BOLT HOLES



AutoCAD SHX TextFLOOR PLATES ONLY WEIGHT = 607.1 kg

AutoCAD SHX Text4 - 150 X 8 FLAT - WELD UNDER FLOOR PLATES AT LOCATIONS SHOWN ABOVE



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text29 DRAW BAR ASSEMBLY


AutoCAD SHX TextINSERT 4" PIPE (114.3mm OD) INTO HOLES, WELD ALL ROUND TOP AND BOTTOM 9 @ 65mm LONG 9 @ 100mm LONG

AutoCAD SHX TextINSIDE DEVELOPMENT OF DRAW BAR ANGLE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextOUTSIDE DEVELOPMENT OF DRAW BAR ANGLE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextDEVELOPMENT OF DRAW BAR BTM PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextTWO ENDS REQ'D

AutoCAD SHX TextTWO ENDS REQ'D

AutoCAD SHX TextDRAW BAR MATERIAL - 3mm MS PLATE

AutoCAD SHX TextDRAW BAR SIDE PLATES MATERIAL 3mm MS PLATE

AutoCAD SHX TextOUTER SIDE PLATE FILL 2 REQ'D

AutoCAD SHX TextINNER SIDE PLATE FILL 2 REQ'D

AutoCAD SHX TextLEFT - DEVELOPMENT OF BOTTOM DRAW BAR SPACER. 4 REQ'D MATERIAL - 3mm MS PLATE BEND TO 6mm INSIDE RADIUS - BENDING ALLOWANCE GIVEN BUTT WELD HALVES TOGETHER.

AutoCAD SHX TextLOCATION OF SPACER

AutoCAD SHX TextCOMPLETED DRAW BAR ANGLE

AutoCAD SHX TextCOMPLETED BOTTOM DRAW BAR SECTION

AutoCAD SHX TextFILL HOLES WITH 4" PIPE WELD ALL ROUND

AutoCAD SHX TextSEE DRAWING "18 REAR GEARBOX DOOR" FOR BOLT HEAD DETAILS

AutoCAD SHX TextSEE DRAWING 63 FOR DRAW BAR ANCHOR

AutoCAD SHX TextFRONT PLATE 2 REQ'D

AutoCAD SHX TextBACK PLATE 2 REQ'D






AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text30 RADIATOR

AutoCAD SHX TextUPPER CW PIPE FIXING FACE MATERIAL - 5mm MS PLATE

AutoCAD SHX TextLOWER CW PIPE FIXING FACE NOTE HOLES ARE OFFSET. MATERIAL - 5mm MS PLATE

AutoCAD SHX TextRADIATOR FACE PAINT MATT BLACK MATERIAL - 3mm MS PLATE

AutoCAD SHX TextRADIATOR SIDE FACE MATERIAL - 5mm MS PLATE

AutoCAD SHX TextRADIATOR SIDE FACE MATERIAL - 5mm MS PLATE

AutoCAD SHX TextASSEMBLY WELD ALL PLATES INSIDE SIDE PLATES. FINALLY FIT RADIATOR COWLING AS SHOWN ABOVE. 4 - M24 x 25 LONG BOLTS REQUIRED TO FIX TOP AND BOTTOM COOLING WATER PIPES.

AutoCAD SHX TextCRANK HANDLE HOLE

AutoCAD SHX TextWELD HEAD LIGHT BRACKET TO SIDE OF RADIATOR 750mm DOWN FROM TOP EDGE

AutoCAD SHX TextCRANK HANDLE SHAFT TO PROTRUDE 10mm NOTE - HANDLE TO BE AT 12 O'CLOCK POSITION.. THEN WELD ALL ROUND TO THIS FACE.






AutoCAD SHX TextNOTE SEE DRAWING 39 FOR RADIATOR ATTACHMENT BRACKETS.

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text31 MUFFLER


AutoCAD SHX TextUPPER CONICAL DEVELOPMENT MATERIAL 3mm MS PLATE

AutoCAD SHX TextLOWER CONICAL DEVELOPMENT MATERIAL 3mm MS PLATE

AutoCAD SHX TextMIDDLE ELLIPTICAL DEVELOPMENT MATERIAL - 3mm MS PLATE

AutoCAD SHX TextMUFFLER DEVELOPMENT ROLL TO 1000 OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextUPPER MUFFLER PIPE DEVELOPMENT ROLL TO 430 OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLOWER MUFFLER PIPE DEVELOPMENT ROLL TO 430 OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE

AutoCAD SHX TextMIDDLE MUFFLER PIPE DEVELOPMENT ROLL TO 585 OUTSIDE DIAMETER MATERIAL 3mm MS PLATE






AutoCAD SHX TextPAINT AS SHOWN WELD ALL ROUND ALL CONNECTIONS

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text32 MUD GUARDS

AutoCAD SHX TextDEVELOPMENT OF INNER PORTION OF MUD GUARD TAPER ROLL TILL OUTSIDE IS 7291 AND 83 HIGH. MATERIAL 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextDEVELOPMENT OF MIDDLE PORTION OF MUD GUARD TAPER ROLL TILL OUTSIDE IS 8064 AND 195 HIGH MATERIAL 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextDEVELOPMENT OF OUTER PORTION OF MUD GUARD TAPER ROLL TILL OUTSIDE IS 8649 AND 241 HIGH MATERIAL 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextDEVELOPMENT OF MUD GUARD RIM. ROLL FLAT TO 4450 RADIUS. MATERIAL 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextSIDE VIEW OF INNER PORTION OF MUD GUARD AFTER ROLLING

AutoCAD SHX TextSIDE VIEW OF MIDDLE PORTION OF MUD GUARD AFTER ROLLING

AutoCAD SHX TextSIDE VIEW OF OUTER PORTION OF MUD GUARD AFTER ROLLING

AutoCAD SHX TextSIDE VIEW OF RIM

AutoCAD SHX TextDEVELOPMENT OF FLAT INNER PORTION OF MUD GUARD. TO BE WELDED TO THE FLOOR PLATES SEE DRAWING 28 - FLOOR PLATES MATERIAL - 5mm MS PLATE 2 REQ'D

AutoCAD SHX TextNOTES WELD ALL PORTIONS TOGETHER TO MAKE ONE LEFT-HAND AND ONE RIGHT-HAND MUD GUARD AS SHOWN BELOW. TRIM END OF GUARD USING SAMPLE PROVIDED AS A GUIDE, SCALE UP 5 TIMES. WELD TO OUTER EDGE OF GUARD 1 " BLACK PIPE AS SHOWN ABOVE. 12" BLACK PIPE AS SHOWN ABOVE. WHEN COMPLETED REFER TO DRAWING 28 'FLOOR PLATES'. WELD ON FLOOR PLATES AS SHOWN.

AutoCAD SHX Text1 " BLACK PIPE 12" BLACK PIPE WELD TO OUTER EDGE OF RIM. BEND PIPE AS REQUIRE TO JUNCTION WITH FLOOR PLATE AT EACH END.

AutoCAD SHX TextDISH



AutoCAD SHX TextTOTAL WEIGHT FOR TWO = 955.5 kg





AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text32.1 MUD GUARD BRACING STEEL

AutoCAD SHX TextVERTICAL BRACING BAR MATERIAL - 125 x 10 FLAT WELD ALL ROUND TO MUD GUARD PLATES ON THE TYRE SIDE 2 REQ'D

AutoCAD SHX Text45 DEGREE ANGLE BRACING BAR MATERIAL - 125 x 10 FLAT WELD ALL ROUND TO MUD GUARD PLATES ON THE TYRE SIDE 2 REQ'D



AutoCAD SHX TextSAME FOR VERTICAL BAR

AutoCAD SHX TextMUD GUARD ATTACHMENT BRACKET MATERIAL 150 x 10 FLAT DRILL ALL HOLES 262 REQ'D

AutoCAD SHX Text 26 HOLES FOR MUD GUARD BRACKET TO BE DRILLED ON ASSEMBLYFIX OTHER END OF BRACKET TO INSIDE THE END OF ENGINE COVER

AutoCAD SHX TextNOTE - 545mm DIMENSION IS NOMINAL AND MUST BE CHECKED WHEN MUD GUARD IS FITTED TO THE TRACTOR



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text33 HAND BREAK AND CLUTCH LEVERS

AutoCAD SHX TextWELD COVER TO THIS SIDE



AutoCAD SHX TextDEVELOPMENT OF HAND BRAKE LEVER LOCK. BEND 20 DEGREES ALONG DASHED LINE THEN WELD ASSEMBLY TO HAND BRAKE LEVER AT THE LOCATION SHOWN. MATERIAL - 3mm MS PLATE CUT TWO PLATES

AutoCAD SHX TextCLUTCH AND HAND BRAKE LEVER SIDE PLATE DEVELOPMENT MATERIAL 3mm MS PLATE 4 REQ'D

AutoCAD SHX TextUPPER CLUTCH LEVER SHAFT DEVELOPMENT ROLL TO 250 OUTSIDE DIAMETER ALSO CUT ONE END COVER PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextHAND BRAKE LEVER SHAFT DEVELOPMENT ROLL TO 250 OUTSIDE DIAMETER ALSO CUT ONE END COVER PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLEVER EDGE PLATES MATERIAL - 65 x 3 FLAT BAR

AutoCAD SHX TextLONG EDGE 2 REQ'D

AutoCAD SHX TextSHORT EDGE 2 REQ'D

AutoCAD SHX TextTOP EDGE 2 REQ'D

AutoCAD SHX TextUPPER CLUTCH LEVER ASSEMBLY



AutoCAD SHX TextHAND BRAKE LEVER ASSEMBLY

AutoCAD SHX TextLOWER CLUTCH LEVER SHAFT DEVELOPMENT ROLL TO 260 OUTSIDE DIAMETER ALSO CUT ONE END COVER PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLOWER CLUTCH LEVER ASSEMBLY

AutoCAD SHX TextLOWER CLUTCH LEVER EDGE PLATE MATERIAL -3mm MS PLATE 2 REQ'D

AutoCAD SHX TextLOWER CLUTCH LEVER SIDE PLATE MATERIAL -3mm MS PLATE 2 REQ'D

AutoCAD SHX TextCLUTCH LINK MATERIAL - 3" BLACK PIPE

AutoCAD SHX TextCLUTCH LINK ENDS MATERIAL - 6" BLACK PIPE AND 3mm MS PLATE

AutoCAD SHX TextNOTE WELD LOWER CLUTCH LEVER TO SIDE OF GEARBOX FIRST. THEN FIT FLOOR PLATES. FINALLY FIT CLUTCH LINK AND UPPER LEVER.



AutoCAD SHX TextDISC WITH HOLE UPPER END

AutoCAD SHX TextDISC LOWER END

AutoCAD SHX TextDISC WITH HOLE

AutoCAD SHX TextINFILL PLATES

AutoCAD SHX TextCUT SLOT ON EACH SIDE TO FIT LEVER




AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text34 Front tyre

AutoCAD SHX TextBEND DOWN 90

AutoCAD SHX TextBEND 99.7




AutoCAD SHX TextBEND115.9








AutoCAD SHX TextNOTES MATERIAL - 3mm MS PLATE ETCH BEND LINES ON PLATE ALL BENDS 9mm OUTSIDE RADIUS (6mm INSIDE RADIUS). CAUTION - TURN PLATE OVER AS REQUIRED TO ACHIEVE FORM SHOWN IN PICTURES. BEND PLATE FIRST THEN PULL ENDS TOGETHER TO ACHIEVE DIMENSION 1265 AND 776 AS SHOWN IN THE PICTURES THEN WELD. 6 PIECES REQUIRED TO MAKE ONE TYRE (TOTAL OF 12 REQ'D) SEE DRAWING 35 FOR DETAILS OF ASSEMBLING TYRE TO RIM.



AutoCAD SHX TextWEIGHT FOR TWO TYRES = 1271 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text35 Front wheel

AutoCAD SHX TextTYRE BEAD ROLL 3" STD WALL PIPE TO 2350 INSIDE DIAMETER 4 REQ'D

AutoCAD SHX TextCUT WHEEL DISCS TO DIAMETER SHOWN MATERIAL - 10mm MS PLATE 2 REQ'D

AutoCAD SHX TextWHEEL CENTER DOME DEVELOPMENT MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextDOME CENTER PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextMOCK WHEEL BEARING HOUSING DEVELOPMENT. MATERIAL 3mm MS PLATE 6 REQ'D TO MAKE TWO.

AutoCAD SHX TextDEVELOPMENT OF WHEEL RIM, ROLL TO 2350 INSIDE DIAMETER MATERIAL 5mm MS PLATE 2 REQ'D

AutoCAD SHX TextDEVELOPMENT OF SPLIT RIM BOLT BEND 90 ALONG DASHED LINE AND WELD. MATERIAL 3mm MS PLATE 10 REQ'D FOR 2 WHEELS

AutoCAD SHX TextNOTE WHEELS TO BE FULLY WELDED TO FRONT AXLE ASSEMBLY

AutoCAD SHX TextHOUSING COVER PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextASSEMBLY DIMENSIONS GRIND AND BLEND ALL EXTERNAL WELDS



AutoCAD SHX TextWEIGHT TWO RIMS = 1179 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text36 FRONT AXLE RADIUS ROD & SPRING

AutoCAD SHX TextSPRING SIDE PLATE DEVELOPMENT MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextDEVELOPMENT OF SPRING BEAM WEB MATERIAL - 8mm MS PLATE

AutoCAD SHX TextDEVELOPMENT OF UPPER BEAM FLANGE DRILL 26 HOLE TO SAME CENTERS AS CENTRAL BEAM ENDAS SHOWN IN DRAWING 15.2 THEN ROLL TO FIT WEB....R5139 MATERIAL - 10mm MS PLATE

AutoCAD SHX TextDEVELOPMENT OF LOWER BEAM FLANGE ROLL TO FIT WEB....R10953 MATERIAL - 10mm MS PLATE

AutoCAD SHX TextBEAM END PLATE MATERIAL - 16mm MS PLATE 2 REQ'D

AutoCAD SHX TextMOCK SPRING END ROLL TO 339 OD AND CUT 560 AND 333 AS SHOWN. MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextRADIUS ROD NUT FACE DEVELOPMENT MATERIAL - 3mm MS PLATE 4 REQ'D

AutoCAD SHX TextRADIUS ROD NUT FLATS DEVELOPMENT BEND 60 DEGREES ALONG DASHED LINE MATERIAL - 3mm MS PLATE 8 REQ'D

AutoCAD SHX TextRADIUS ROD DETAILS MATERIAL - 8" BLACK PIPE STD WALL (219mm OD) 4 BLACK ELBOWS REQ'D

AutoCAD SHX TextPLATE SHACKLE SPACER MATERIAL - 8" BLACK PIPE 4 REQ'D

AutoCAD SHX TextMOCK "U" BOLT MATERIAL - 3" BLACK PIPE 2 REQ'D

AutoCAD SHX TextLEAF SPRING PLATE AND PIN MATERIAL - 10mm MS PLATE 1" BLACK PIPE 4 PLATES AND 2 PINS REQ'D

AutoCAD SHX TextPLASMA CUT LINES SHOWN

AutoCAD SHX TextSPRING CENTER SWIVEL ROLL CENTER 707 TO R225 MATERIAL - 3mm MS PLATE

AutoCAD SHX TextSHACKLE FACE AND EDGE ROLL END 236mm TO R150 MATERIAL - 3mm MS PLATE 4 FACE AND 8 EDGE REQ'D

AutoCAD SHX TextTOW TONGUE EDGE DEVELOPMENTS ROLL MIDDLE 590 TO R375 MATERIAL - 3mm MS PLATE

AutoCAD SHX TextSHACKLE BOLT HEAD DEVELOPMENT BEND 60 DEGREES ALONG DASHED LINE MATERIAL - 3mm PLATE 8 TOPS AND 16 PLATES REQ'D

AutoCAD SHX TextTOW TONGUE ASSEMBLY

AutoCAD SHX TextTOW TONGUE BOLT PLATE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextUPPER TOW TONGUE PLATE MATERIAL 3mm MS PLATE

AutoCAD SHX TextLOWER TOW TONGUE PLATE MATERIAL 3mm MS PLATE

AutoCAD SHX TextTOW TONGUE BOLT HOLE MATERIAL - 6" BLACK PIPE

AutoCAD SHX TextTOW TONGUE BOLT HEAD 2 NUT SIDES REQ'D MATERIAL - 3mm MS PLATE

AutoCAD SHX Text"U" BOLT PLATE MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextFRONT TRACTOR SUPPORT BEAM BEAM END PLATES WELDED TO AXLE BEAM TOP PLATE - WELD ALL ROUND NOTE LOCATION OF CENTRAL WEB STIFFING PLATES

AutoCAD SHX TextLEAF SPRING ASSEMBLY




AutoCAD SHX TextWEB STIFFENING PLATES - 2 REQ'D @ 300mm 4 REQ'D @ 250mm MATERIAL - 10mm MS PLATE

AutoCAD SHX TextLOCATION OF WEB STIFFING PLATES - WELD ALL ROUND TO WEB AND BEAM FLANGES - BOTH SIDES



AutoCAD SHX TextINSIDE

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text37 Distributor cover

AutoCAD SHX TextDEVELOPMENT OF COVER PLATE ROLL MIDDLE 832 TO R265 OUTSIDE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextASSEMBLY DIMENSIONS

AutoCAD SHX TextDEVELOPMENT OF END PLATE ROLL BOTTOM 400 TO R251 OUTSIDE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextEND PLATE

AutoCAD SHX TextEND PLATE






AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text39 FRONT ENGINE TO RADIATOR CASTING


AutoCAD SHX TextBEND 15



















AutoCAD SHX TextBOTTOM PLATE DEVELOPMENT MATERIAL - 3mm MS PLATE

AutoCAD SHX TextFRONT PLATE MATERIAL = 10mm MS PLATE

AutoCAD SHX TextINSIDE PLATE MATERIAL - 10mm MS PLATE 2 REQ'D

AutoCAD SHX TextCURVED OUTER PLATE DEVELOPMENT MATERIAL - 3mm MS PLATE 2 REQ'D ONE LH AND ONE RH

AutoCAD SHX TextCURVED TOP PLATE DEVELOPMENT MATERIAL - 3mm MS PLATE 2 REQ'D ONE LH AND ONE RH

AutoCAD SHX TextTOP CURVED PLATE DEVELOPMENT MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextASSEMBLY TO BE WELDED TO ENGINE BLOCK NOTE - USE RADIATOR TO LOCATE BRACKETS

AutoCAD SHX TextRADIATOR SUPPORT BRACKET BOLT BRACKETS TO RADIATOR - ALIGN THEN WELD MATERIAL - 10mm MS PLATE 2 REQ'D






AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text40 NAME PLATES


AutoCAD SHX TextBACKING PLATE MATERIAL = 10mm MS

AutoCAD SHX TextFRONT PLATE MATERIAL = 10mm MS

AutoCAD SHX TextCUT LETTERS SHOWN MATERIAL - 10mm MS PLATE PLACE ON BACKING PLATE AND WELD THROUGH OPENINGS PROVIDED.. PERIMETER WELD BACKING PLATE TO FRONT PLATE, GRIND FLAT.

AutoCAD SHX TextCUT LETTERS SHOWN MATERIAL - 10mm MS PLATE PLACE ON BACKING PLATE AND WELD THROUGH OPENINGS PROVIDED.

AutoCAD SHX TextFRONT PLATE MATERIAL = 10mm MS

AutoCAD SHX TextPLACE LETTERS ON BACKING PLATE AND WELD THROUGH OPENINGS PROVIDED.


AutoCAD SHX TextBACKING PLATE MATERIAL = 10mm MS

AutoCAD SHX TextNOTE BEND BACKING AND FRONT PLATE TO 10.5m RADIUS TO FIT GRILL. "V" PREP THEN WELD AROUND OUTSIDE PERIMETER. - GRIND FLAT.

AutoCAD SHX TextPAINT BACKGROUND RED AS SHOWN POSITION "MADE IN AUSTRALIA" PLATE AS SHOWN ABOVE.

AutoCAD SHX TextCUT LETTERS SHOWN. CUT 3980 x 162 BACKING PLATE. MATERIAL - 10mm MS PLATE (BOTH). SPACE LETTERS ON BACKING PLATE AND FILLET WELD EACH LETTER TO BACKING PLATE TOP AND BOTTOM. NOTE - 2 REQ'D ONE FOR EACH SIDE OF THE TRACTOR

AutoCAD SHX TextBACKING PLATE 10mm



AutoCAD SHX TextWEIGHT = 228 kg (estimated)



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text41 Engine cover rear mounting

AutoCAD SHX TextASSEMBLY "U" BRACKETS TO BE WELDED TO THE INSIDE OF THE ENGINE COVER AT PRE - ASSEMBLY. 16 - M24 x 50 LONG BOLTS AND NUTS REQ'D.

AutoCAD SHX TextCROSS BEAM MATERIAL - 150 x 16 FLAT 2 REQ'D

AutoCAD SHX Text"U" PLATE MATERIAL - 150 x 10 FLAT 4 REQ'D

AutoCAD SHX TextBOLT PLATE MATERIAL - 150 x 10 FLAT 4 REQ'D

AutoCAD SHX TextMOUNTING SHEET INFILL MATERIAL - 3mm MS PLATE ONE OF EACH TYPE REQ'D

AutoCAD SHX TextSIDE PLATES MATERIAL - 3mm MS PLATE 2 REQ'D NOTE - CUT HOLES FOR AIR CLEANER BRACKET AFTER ASSEMBLY.

AutoCAD SHX TextENLARGED DETAIL OF FRONT PLINTHS

AutoCAD SHX TextFRONT PLINTH MATERIAL - 10mm MS PLATE 2 REQ'D

AutoCAD SHX TextLEGS ONE REQ'D WITH HOLES. 2 OF EACH HAND REQ'D. SEE ASSEMBLY

AutoCAD SHX TextBASE ANGLES MATERIAL 10mm MS PLATE ONE OF EACH TYPE REQ'D

AutoCAD SHX TextDIAGONAL MATERIAL 10mm MS PLATE 4 REQ'D






AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text42 CYLINDER HEAD

AutoCAD SHX TextSIDE OF CYLINDER HEAD ROLL 197 TO R127 OUTSIDE MATERIAL - 3mm MS PLATE 4 REQ'D

AutoCAD SHX TextSPARK PLUG SHIELD ROLL 750 TO R318 OUTSIDE WELD TO THE HEAD AS SHOWN BELOW. 2 REQ'D

AutoCAD SHX TextCYLINDER HEAD FACE ETCH MARK LOCATIONS OF SPOT FACES MATERIAL - 3mm MS PLATE 2 REQ'D

AutoCAD SHX TextSPOT FACE CUT CENTER HEX OUT MATERIAL - 3mm MS PLATE 20 REQ'D

AutoCAD SHX TextHEAD BOLT FACE FROM SPOT FACE MATERIAL - 3mm MS PLATE 20 REQ'D

AutoCAD SHX TextHEAD BOLT FACE BEND 60 DEGREES MATERIAL - 3mm MS PLATE 60 REQ'D

AutoCAD SHX TextSPECIAL NOTE THE RIGHT HAND CYLINDER HEAD IS SHOWN, THE LEFT HAND HEAD IS OF THE OPPOSITE HAND. THE SPARK PLUG COVER IS ON THE REAR OF THE HEAD.PLUS THE BOTTOM MIDDLE BOLT IS NOT CENTRAL. RANDOM ROTATE NUTS FOR AUTHENTICITY (NOT AS SHOWN).



AutoCAD SHX TextTOTAL WEIGHT x 2 = 254 kg



AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text43 CYLINDER BLOCK

AutoCAD SHX TextRIGHT HAND CYLINDER BLOCK CUT 2 PLATES, 1 WITHOUT DIA 26 HOLES AT 197mm LOCATIONS ROLL TO R127 OUTSIDE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLEFT HAND CYLINDER BLOCK CUT 2 PLATES, 1 WITHOUT DIA 26 HOLES AT 197mm LOCATIONS ROLL TO R127 OUTSIDE MATERIAL - 3mm MS PLATE

AutoCAD SHX TextEND VIEW OF PLATE AFTER ROLLING

AutoCAD SHX TextRIGHT HAND BLOCK SHOWN ABOVE






AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text44 Bottom CW pipes

AutoCAD SHX TextDEVELOPMENT OF BOTTOM COOLING WATER PIPES. LEFT HAND SIDE FROM BLOCK TO RADIATOR SHOWN ABOVE. ROLL TO NOMINAL OUTSIDE DIAMETER OF 350mm. MATERIAL - 3mm MS PLATE

AutoCAD SHX TextMAKE UP 4 PIPE FIXING BRACKETS MATERIAL - 150 x 10 FLAT AND M24 x 75 LONG BOLT AND NUT LAY ASSEMBLED PIPES FLAT WITH FIXING BRACKETS VERTICALLY AS SHOWN BELOW. RECESS BRACKET 5mm INSIDE PIPE THEN WELD.

AutoCAD SHX TextDEVELOPMENT OF BOTTOM COOLING WATER PIPES. RIGHT HAND SIDE FROM BLOCK TO RADIATOR SHOWN ABOVE. ROLL TO NOMINAL OUTSIDE DIAMETER OF 350mm. MATERIAL - 3mm MS PLATE






AutoCAD SHX TextWELD HEXAGON NUT TO PLATE

AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text45 Top CW pipes

AutoCAD SHX TextMAKE UP 4 PIPE FIXING BRACKETS MATERIAL - 150 x 10 FLAT AND M24 x 75 LONG BOLT AND NUT RECESS BRACKET 5mm INSIDE PIPE THEN WELD. NOTE ORIENTATION OF FIXING BRACKETS SHOWN LEFT. UPPER VERTICAL. LOWER IN LINE WITH CRANK SHAFT.

AutoCAD SHX TextRIGHT HAND TOP COOLING WATER PIPE DEVELOPMENT ROLL TO 350mm OUTSIDE DIAMETER ETCH ALIGNMENT MARKS TO AID ASSEMBLY MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLEFT HAND TOP COOLING WATER PIPE DEVELOPMENT ROLL TO 350mm OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE







AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text46 Top CW pipes

AutoCAD SHX TextMAKE UP 2 PIPE FIXING BRACKETS MATERIAL - 150 x 10 FLAT AND M24 x 75 LONG BOLT AND NUT RECESS BRACKET 5mm INSIDE PIPE THEN WELD. NOTE ORIENTATION OF FIXING BRACKETS SHOWN LEFT..

AutoCAD SHX TextRIGHT HAND EXHAUST PIPE ROLL TO 400mm OUTSIDE DIAMETER ETCH ALIGNMENT MARKS TO AID ASSEMBLY MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLEFT HAND EXHAUST PIPE ROLL TO 400mm OUTSIDE DIAMETER MATERIAL - 3mm MS PLATE







AutoCAD SHX TextA3

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX Text4

AutoCAD SHX Text1

AutoCAD SHX Text2

AutoCAD SHX Text3

AutoCAD SHX Text4

AutoCAD SHX TextC

AutoCAD SHX TextA

AutoCAD SHX TextB

AutoCAD SHX TextC

AutoCAD SHX TextA3








AutoCAD SHX Text47 Inlet pipes

AutoCAD SHX TextMAKE UP 2 PIPE FIXING BRACKETS MATERIAL - 150 x 10 FLAT AND M24 x 75 LONG BOLT AND NUT RECESS BRACKET 5mm INSIDE PIPE THEN WELD. NOTE ORIENTATION OF FIXING BRACKETS SHOWN LEFT..

AutoCAD SHX TextRIGHT HAND INLET PIPE ETCH ALIGNMENT MARKS FOR CORRECT ASSEMBLY ROLL TO 340mm OUTSIDE DIAMETER ETCH ALIGNMENT MARKS TO AID ASSEMBLY MATERIAL - 3mm MS PLATE

AutoCAD SHX TextLEFT HAND INLET PIPE ETCH AL

Date post:	28-Mar-2021
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

Date: 30 April 2020 - 01-21... · 2021. 1. 22. · The key design assumption is that the steelwork...

Documents