Date post: | 27-Dec-2015 |
Category: |
Documents |
Upload: | nigel-todd |
View: | 219 times |
Download: | 0 times |
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20091
IBL Data and TTC Transmission Baseline
Presented by
David [email protected]
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20092
Contributors
ATLAS Pixel System Design Task Force for SLHC Upgrade
A. Grillo – lead F. Anghinolfi, M.B. Barbero,
R. Beccherle, G. Darbo, F. Philippe,
D. Ferrere, M. Garcia-Sciveres,
T. B. Huffman, S. Kersten, S. Malyukov,
D. J. Nelson, F. Hügging.
Transmission testingMartin Kocian, D. J. Nelson, Su Dong
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20093
IBL I/O system proposed by task force.Due to the short schedule for development and to minimize risk and cost.
Note that the IBL is not a stand-alone system, but an add-on.
Use as much of the existing elements as possible while meeting requirements.
Minimize development effort, cost and integration time with existing system
The LHC down time will be close to normal with minimal commissioning time for the IBL.
Man-power is in short supply for development work
New elements would be difficult to qualify given the schedule.
Perform early testing of components.For example, the opto-board to electrical EOS communication can be proto-typed immediately as proposed by the task force.
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20094
IBL I/O system Requirements & Recommendations.
Data RatesThe B-Layer at 3.7 cm and a luminosity of 3 x LHC indicate that a data rate of 86 Mbps per FE-I4. Allow for 30% uncertainly in occupancy simulation. There is also likely need for 8B-10B encoding for clock recovery which adds 20% overhead. The total data rate could be 129 Mbps with the uncertainty and 8B-10B encoding.
An alternate approach is to scale existing layers L1 & L2 maximum bandwidth to 3.7 cm radius.
Both approaches lead to a data rate set to 160M bps
Task force recommendationThe data rate per FE-I4 is set at 160Mbps
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20095
IBL I/O system Requirements & Recommendations.
Clock & CommandTwo options were considered.
Send 40MHz and provide a clock multiplier on the FE-I4This allows the TTC chain to operate as now but requires a new clock multiplier on the front-end readout chip.FE-I4 designers are OK with developing a clock multiplier.
Send 80MHz and use both edges as now done to achieve the 160Mbps data output.
Require modifications to the BOC & possibly to the ROD to produce higher speed TTCA synchronization protocol would have to be developed and built into the FE-I4 to provide correct phasing of the beam crossing to the 80MHz clock.Require a new DORIC chip to decode the clock at twice the frequency.
Task force recommendationTake the decoded clock (40MHz) & commands (40Mbps) from the DORIC and propagate them as separate LVDS lines from the opto-boards to the FE-I4s. It should be possible to connect two FE-I4 chips to each clock and command thus reducing the electrical links by a factor of two.
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20096
IBL I/O system Requirements & Recommendations.
Task force Data Output Links recommendations:
Run links at 160Mbps
One link between each FE-I4 and the opto-boards where the VDC and VCSEL will convert them to optical. One optical link per LVDS link.
LVDS over copper twisted pair, 36 AWG
Include 8B-10B encoding in the FE-I4
The BOC would include 8B-10B decoding as well
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20097
IBL I/O system Requirements & Recommendations.
BOC/RODBOC will need to be redesigned to handle receipt of the 160MHz data stream and decode 8B-10B data back to its raw form
The simplest adaptation would be to have the BOC hand off the data to the ROD as four 40 Mbps data streams for each input link as it now separates the 80 Mbps data streams into two 40 Mbps streams.
This will minimize changes in the ROD and still require one S-Link per two 40 Mbps data streams.
The BOC could hopefully be backward compatable.
Strong requirement is that the RODs built for the IBL be backward compatible with the existing ROD so they can be used for spares.
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20098
IBL I/O system Requirements & Recommendations.
Possible Opto-board UpgradeSome redundancy could be added to allow dead TTC and Data Out links to be replaced by spare channels.
A separate control of the VCSEL optical power would improve robustness.
Task force recommendationsThese added features would be helpful for the existing system and should be seriously considered for the SLHC upgrade.
The IBL is a small portion of the system and is short lived.
Therefore The task force recommends not to include these upgrades to the opto-boards
DCS and InterlocksTask force recommendations
Use the same components that are used in the present Pixel system
David NelsonIBL Data & TTC Transmission Baseline
February 25, 20099
Near Term Tests, (Task Force Recommendations)
Several aspects of the proposed plan for the IBL should be tested in the very near future.
Reliable electrical transmission of DC balanced 160 Mbps signals over the estimated 4 meters from the FE-I4 chips to the planned location of the opto-boards should be verified.
Slide 15 illustrates successful tests
Test the ability of the existing VDC chip to drive 160 Mbps.
Verify that the present DORIC chip can reliably transmit 40 MHz clock and 40 Mbps commands over 4 meters via twisted pair copper.
Verify that two FE-I4 can share the same clock and command lines.
A test of these services chain using existing opto-board and LVDS test chip should be employed as soon as possible. Results of these tests could impact these architectural decisions.
Slide 15 illustrates that the ATPIX test chips performs well
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200910
Options for FE-I4 Design
The FE-I4 should include a reset-clock-multiplier command.
The FE-I4 should be provided with a second 80 MHz input.This would allow to either use the clock multiplier or this alternate input.
Pre-emphasis could be added to the FE-I4 if tests show difficulty in transmitting 160 Mbps
Pre-emphasis could be added to the DORIC if tests show that the present DORIC has trouble transmitting data over 4 meters.
Could this be a commercial chip which would avoid a design effort.
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200911
IBL EOS ServicesPower
The current system uses an equivalent of 4 pair of 17 AWG Al wire.Total current for 16 FE-I4 chips is 9.6 Amps * 2 is 19.2 amps for total pin current.Four meters lengthThe cross section of the 4 pair is 8.3mm^2.A number of power connections have been discussed
Use Hirose DF30, 40 pin board to board connectorsPlastic body is Liquid Crystal Polymer, (LCP)
Radiation good to > 100MGyContact rating is 0.3 ampsDe-rate to 0.15 amps19.2 amps / 0.15 = 128 pinsWould need 3 each 40 pin connectorsWire gauge would need to be 28 AWG Al or larger
Can the wires be silver plated for solderability?Directly solder wires to IBL
Could use any combination of wire gauges to attain required voltage drops.No contact de-rating needed.More reliableMore difficult to handle during fabrication.
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200912
IBL EOS ServicesClock and Command
16 pair of 36 AWG copper twisted pair8 clock, 8 Command.One pair for two FE-I4sOne 40 pin HRS DF30 connectorCould directly solder wire to IBL
Data link16 pair of 36 AWG copper twisted pair
One pair per FE-I4One 40 pin HRS DF30 connectorCould directly solder wire to IBL
High VoltageTwo 20 pin HRS DF30 connector
8 HV circuits?Use low voltage returnsCould directly solder wire to IBL
This would accommodate the voltage compliance
DCSSeparate connector
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200913
IBL EOS Services
IBL – 84 cm
EOS Shrink & surgicalTubing
EOS with HRSConnectors & 0-80Screws – 10 cm
Still playing with fastening mechanism
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200914
IBL EOS Services with traveling harness
EOS with traveling
with traveling harness
All wires soldered
and spooled
Assembly test with
multi-stave
IBL
10 cm -15 cmdiameter spool
Directsolderwires
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200915
IBL Data Transmission using the ATPIX Transceiver Chip
Test-up includes:Xilinx ML-405 developmentboardRandom pattern test codeMartin KocianATPIX LVDS test chipTwo PPA-0 flex circuits – 50 cmOne HRS connectorOne – 4 meter twisted pair36 AWG wire160 Mbps data rateEye pattern is 317mV, need > 200mVCross talk measurement OKWe should consider MLVDS receivers
Eye requirement is 100mV
No errors @ 150 Mbps or 350 MbpsError rate better than 2*10-13 @ 350 Mbps
50 OHM
TEST CHIP LVDS DRIVERXILINX DEVELOPMENTBOARD - ML405
100 OHM4 METER TWISTED PAIR 36-AWG
COPPER80 OHM
50 CM PPA-0 FLEX100 OHM
HRS DF30CONNECTOR
IBL DATA TRANSMISSION TEST SETUP
LVDS RECEIVER
CMOSDRIVER
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200916
Testing
Current testsVerified that the proposed IBL EOS services can operate at 160 Mbps with margin – previous slide
Test setup operates without errors at 350 Mbps
Verified that the ATPIX LVDS test chip will perform with margin
Needed testsSystem level test should start as soon as possible
Namely EOS to opto-board electrical communications can start immediately
Test full I/O chain
Test the ability of the existing VDC chip to drive 160 Mbps.
Test the existing opto-board and LVDS test chip together.
Test DORIC to drive 40 MHz clock and 40 Mbps data over 4 meters
Test services chain using existing opto-board and ATPIX LVDS chip
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200917
What more is needed
Testing .. Testing.. TestingGet closure on requirements of FE-I4Modify BOC
Include 8B-10BSeparate the 160 Mbps into 4 lanes of 40 Mbps
Finalize powering schemeVoltage drop budgetHigh voltage segmentation
Design flex cableFinalize EOS connector/solder interface optionsFinalize how to secure cable on EOSUnderstand grounding and shielding
Common mode voltages could be a potential issue Due to the lower common mode voltage of the 1.5 volt LVDS designDue to varying voltage drops on each section of the IBL
David NelsonIBL Data & TTC Transmission Baseline
February 25, 200918
Summary
The ATLAS Pixel System Design Task Force has provided a list of recommendations for minimizing the risk and cost of deployment of the IBL
Initial tests of the data transmission illustrates that 160 Mbps data transmission over 4 meters on twisted pair wire is quite manageable
New specifications for the FE-I4 need to be finalized and design started soon.
New specifications for the BOC need to be finalized and design started soon