DRAFT
The Company
Established in 1991, Adel System design and manufactures industrial power supplies based on Linear and Switching technology. The know-how developed in these years enables ADEL to satisfy a wide range of applications in industrial automation.
Technology:
During the past years, the development effort has focused on switching technology. We can now meet the most demanding requirements for AC/DC and DC/DC power supplies, UPS systems and battery chargers. The experience of our engineering team, always facing new challenges, insures high quality and cost-effi ciency of our products.
Quality:
Aware that even a short interruption of service can cause large material and economic losses, 100% of ADEL’s products are tested and commissioned in the factory. Each product undergoes functional tests,12 or 24-hour run-in test at maximum operating voltage and current, and all the test required for CE marking. This is part of our continuing improvement policy, which aims to deliver highly reliable products to our Clients. Special attention is given to components’ selection. For istance the PSM and the PST product ranges feature long duration electrolytic capacitors with maximum working temperature of 105°C. The compatibility with CE requirements on electromagnetic interference is tested in our internal laboratory.
Applications:
The wide range of products, from a few watts to the kW size, allows technical expert to have a wide choice for each application. When special requirements of our Clients demand for a customized product, ADEL’s engineering staff is fast and fl exible.
Approvals:
All ADEL’s products are CE marked. The PSM range are cCSAus certifi ed according to European Standards EN60950, US UL60950, Canada CAN/CSA C22.2 N. 60950-00.
Installation:
Our products are the winning solution especially when installed inside control panels. They are all equipped with DIN rail mounting clip. They are easily installed and removed without the need of special tools and are safe against accidental falls.
Capacity Reserve:
All our products have been developed with two key parameters: they can be switched on with capacitive loads up to 30,000µF and they all have a 10% reserve above rated current. This allows our units to withstand the high transient currents associated with normal applications.
Industrial Power SuppliesAADDEELL ssyysstteemm
3
AADDEELL ssyysstteemm
DRAFTIndustrial Switching Mode Power Supplies
Industrial Switching Mode Power SuppliesInput Voltage
VACWattsVDC Output Volts Output Amps Approvals Catalog
Number Price
Single Phase
115-230 60 24 2.5 PSM242A
115-230 120 24 5 PSM244A
115 240 24 10 PSM2410A
230 240 24 10 PSM2410C
Two Phase
400-480 168 24 7 PSM247BU
400-480 168 24 7 PSM247B
400-480 240 24 10 PSM2410B
�� ��
�� ��
�� ��
�� ��
�� ��
�� ��
➊ Product has been submitted for UL508 Industrial Control equipment rating. Now pending.➋ PSM247B is approved for CE and cCSAus only.➋ Also available in 12VDC and 5VDC output on special order.
➊
➊
➊
➊
➋
➊
�� ��
➊
4
AADDEELL ssyysstteemm
DRAFT
Industrial Switching Mode Power Supplies
PSM242AInput: single-phase 115 - 230 VacOutput: One output 2.5 A - 24 Vdc 60 WattsStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small sizeAvailable: 12Vdc/2.5A and 5Vdc/2.5A
FeaturesInput DataInput Rated Voltage (2 x Vac) 115 – 230 VacRated Voltage range 93 ÷ 264 VacInrush Current (Vn – In) ≤ 11 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 0.9 – 0.5 AInternal Fuse F 4 AExternal Fuse (recommended) Fast 4 A
Output DataOutput Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 2.5AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 20.000 / ≤ 30.000µFSwitching on delay applying mains voltage 2.5 sec. (max)Max. Continuous Current 1.1 x IN ± 5%Reserve Out Current (max. 1 min. 50 °C) IMAX=IN+25% approx.Hold-up Time (at 100 – 240 Vac) Typ. 27 msecResidual Ripple ≤ 60 mVppMinimum Load NoEfficiency ≥ 81 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection Yes (max 35 Vdc)Parallel connection Yes
Climatic DataAmbient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General DataIsolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 50x95x155 mmWeight 0.45 kg approx.
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The device must be installed according to IEC/EN 60950.
GenericImmunity according to EN50082-2 Level 4 Class BNoise Radiation according to EN 55011
Output Derating Curve
Output Characteristic Curve U/I
Dimensions
�� ��
5
AADDEELL ssyysstteemm
DRAFT
PSM244AInput: single-phase 115 - 230 VacOutput: One output 5 A - 24 Vdc 120 WattsStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small sizeAvailable: 48Vdc/2.5A, 12Vdc/5A and 5Vdc/5A
FeaturesInput DataInput Rated Voltage (2 x Vac) 115 – 230 VacRated Voltage range 93 ÷ 264 VacInrush Current (Vn – In) ≤ 11 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 0.9 – 0.5 AInternal Fuse F 4 AExternal Fuse (recommended) Fast 4 A
Output Data
Output Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 5AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 30.000µFSwitching on delay applying mains voltage 3 sec. (max)Max. Continuous Current 1.1 x IN ± 5%Reserve Out Current (max. 1 min. 50 °C) IMAX=IN+25% approx.Hold-up Time (at 100 – 240 Vac) Typ. 27 msecResidual Ripple ≤ 60 mVppMinimum Load NoEfficiency ≥ 82 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection Yes (max 35 Vdc)Parallel connection Yes
Clilmatic Data
Ambient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General Data
Isolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 55x115x155 mmWeight 0.70 kg approx.
Output Derating Curve
Output Characteristic Curve U/I
Dimensions
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The unit must be installed according to IEC/EN 60950.
GenericImmunity according to EN50082-2 Level 4 Class BNoise Radiation according to EN 55011
Industrial Switching Mode Power Supplies
�� ��
6
AADDEELL ssyysstteemm
DRAFT
PSM2410AInput: single-phase 115 VacOutput: One output 10 A - 24 Vdc 240 WattsStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small sizeAvailable: 12Vdc/10A and 5Vdc/10A
FeaturesInput DataInput Rated Voltage (2 x Vac) 115 Vac Rated Voltage range 90 ÷ 132 VacInrush Current (Vn – In) ≤ 14 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 3.5A maxInternal Fuse F 6.3 AExternal Fuse (recommended) Fast 6 A
Output Data
Output Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 10AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 30.000µFSwitching on delay applying mains voltage 2.5 sec. (max)Max. Continuous Current 1.1 x IN ± 5%Reserve Out Current (max. 1 min. 50 °C) IMAX=IN+25% approx.Hold-up Time (at 100 – 240 Vac) Typ. 27 msecResidual Ripple ≤ 60 mVpp
Minimum Load NoEfficiency ≥ 86 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection Yes (max 35 Vdc)Parallel connection Yes
Clilmatic Data
Ambient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General Data
Isolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 132x118x135 mmWeight 1.15 kg approx.
Output Derating Curve
Output Characteristic Curve U/I
Dimensions
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The unit must be installed according to IEC/EN 60950.
GenericImmunity according to EN50082-2 Level 4 Class BNoise Radiation according to EN 55011
Industrial Switching Mode Power Supplies
�� ��
7
AADDEELL ssyysstteemm
DRAFT
PSM2410CInput: single-phase 2305 VacOutput: One output 10 A - 24 VdcStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small size
Features
Input Data
Input Rated Voltage (2 x Vac) 230 Vac Rated Voltage range 187 ÷ 264 VacInrush Current (Vn – In) ≤ 14 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 3.5A maxInternal Fuse F 6.3 AExternal Fuse (recommended) Fast 6 A
Output Data
Output Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 10AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 30.000µFSwitching on delay applying mains voltage 2.5 sec. (max)Max. Continuous Current 1.1 x IN ± 5%Residual Ripple ≤ 60 mVpp
Minimum Load NoEfficiency ≥ 86 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection YesParallel connection Yes
Clilmatic Data
Ambient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General Data
Isolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 132x118x135 mmWeight 1.15 kg approx.
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The unit must be installed according to IEC/EN 60950.
GenericImmunity according to EN50082-2 Level 4 Class BNoise Radiation according to EN 55011
AvailablePSM1210C (12Vdc, 10 A)PSM0510C (5Vdc, 10 A)
Output Derating Curve
Output Characteristic Curve U/I
Dimensions
�� ��
8
AADDEELL ssyysstteemm
DRAFT
PSM247BUInput: two-phase 400 - 480 VacOutput: One output 7 A - 24 Vdc 168 WattsStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small size
Output Derating Curve
Output Characteristic Curve U/I
Features
Input DataInput Rated Voltage (2 x Vac) 400 – 480 VacRated Voltage range 360 ÷ 530 VacInrush Current (Vn – In) ≤ 17 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 0.7 - 0.6 AInternal Fuse F 4 AExternal Fuse (recommended) Fast 4 A
Output Data
Output Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 7AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 30.000µFSwitching on delay applying mains voltage < 1 sec. (max)Max. Continuous Current 10A±5% (max)Reserve Out Current (max. 1 min. 50 °C) IMAX=IN+25% approx.Hold-up Time (at 100 – 240 Vac) Typ. 27 msecResidual Ripple ≤ 60 mVpp
Minimum Load NoEfficiency ≥ 88 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection Yes (max 35 Vdc)Parallel connection Yes
Clilmatic Data
Ambient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General Data
Isolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 55x115x155 mm Weight 0.70 kg approx.
Industrial Switching Mode Power Supplies
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The unit must be installed according to IEC/EN 60950.
�� ��
Dimensions
9
AADDEELL ssyysstteemm
DRAFT
PSM247BInput: two-phase 400 - 480 VacOutput: One output 7 A - 24 Vdc 168 WattsStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small size
Output Derating Curve
Output Characteristic Curve U/I
Features
Input DataInput Rated Voltage (2 x Vac) 400 – 480 VacRated Voltage range 360 ÷ 530 VacInrush Current (Vn – In) ≤ 17 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 0.7 – 0.6 AInternal Fuse F 4 AExternal Fuse (recommended) Fast 4 A
Output Data
Output Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 7AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 30.000µFSwitching on delay applying mains voltage 2.5 sec. (max)Max. Continuous Current 1.1 x IN ± 5%Reserve Out Current (max. 1 min. 50 °C) IMAX=IN+25% approx.Hold-up Time (at 100 – 240 Vac) Typ. 27 msecResidual Ripple ≤ 60 mVpp
Minimum Load NoEfficiency ≥ 88 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection Yes (max 35 Vdc)Parallel connection Yes
Clilmatic Data
Ambient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General Data
Isolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 132x118x135 mm Weight 1.15 kg approx.
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The unit must be installed according to IEC/EN 60950.
GenericImmunity according to EN50082-2 Level 4 Class BNoise Radiation according to EN 55011
Industrial Switching Mode Power Supplies
Dimensions
�� ��
10
AADDEELL ssyysstteemm
DRAFT
PSM2410BInput: two-phase 400 - 480 VacOutput: One output 10 A - 24 Vdc 240 WattsStrong overload without switch-offShort-circuit protectionOver-voltage protectionIP20DIN Rail MountableExtremely small size
Features
Input DataInput Rated Voltage (2 x Vac) 400 – 480 VacRated Voltage range 360 ÷ 530 VacInrush Current (Vn – In) ≤ 17 A ≤ 5 msec.Frequency 47 ÷ 63 HzInput Current (Input Rated Voltage) 1 – 0.85 AInternal Fuse F 4 AExternal Fuse (recommended) Fast 4 A
Output Data
Output Voltage (Vn) / Nominal Current (In) 24 Vdc ±3% / 10AAdjustment range (Vadj) 22 ÷ 26 VdcStart up with Strong Load (capacitive load) ≤ 30.000µFSwitching on delay applying mains voltage 2.5 sec. (max)Max. Continuous Current 1.1 x IN ± 5%Reserve Out Current (max. 1 min. 50 °C) IMAX=IN+25% approx.Hold-up Time (at 100 – 240 Vac) Typ. 27 msecResidual Ripple ≤ 60 mVpp
Minimum Load NoEfficiency ≥ 89 %Short-circuit protection (hiccup mode) Yes Over Load protection (hiccup mode) Yes Over Voltage Output protection Yes (max 35 Vdc)Parallel connection Yes
Clilmatic Data
Ambient Temperature (operation) -10 ÷ +70 °C (>50°derating)Ambient Temperature (Storage) -25 ÷ +85 °CHumidity; no moisture condensation 95 % to 25 °C
General Data
Isolation Voltage (Input/Output) 3000 VacInput / ground isolation PE 1605 VacOutput / ground isolation PE 500 VacDegree of protection IP 20Protection class I with PE connectedDimension (w-h-d) 132x118x135 mmWeight 1.15 kg approx.
Output Derating Curve
Output Characteristic Curve U/I
Dimensions
Industrial Switching Mode Power Supplies
Norms and certificationsAccording to EMC 89/336/EEC and Low voltage 93/68/EEC
Electrical SafetyAccording to IEC/EN 60950 (VDE 0805) e EN 50178 (VDE 0160) for assembling device. The unit must be installed according to IEC/EN 60950.
GenericImmunity according to EN50082-2 Level 4 Class BNoise Radiation according to EN 55011
�� ��
11
AADDEELL ssyysstteemm
DRAFT
50mm
95m
m
155mm
PSM244A
PSM2410B
PSM247BU
Dimensions
PSM242A
PSM2410A and PSM2410C
PSM247B
50mm
95m
m
132mm 135mm
118m
m
155mm 50mm
95m
m
155mm
132mm 135mm
118m
m
132mm 135mm
118m
m
Industrial Switching Mode Power Supplies
Divisional Headquarters
Sprecher+Schuh US Division Headquarters15910 International Plaza Dr., Houston, TX 77032Tel: (281) 442-9000 Fax: (800) 739-7370
Sprecher+Schuh Canadian Division3610 Nashua Dr., Unit 10, Mississauga, Ontario LV4 1L2Tel: (905) 677-7514 Fax: (905) 677-7663www.sprecherschuh.com
Publication No: LIT-CAT-ADEL-16 08/06