Date post: | 05-Apr-2018 |
Category: |
Documents |
Upload: | jefflanders |
View: | 247 times |
Download: | 0 times |
of 21
7/31/2019 DDP Instructions
1/21
DDP-1 Digital Distribution Products
6th Edition
7/31/2019 DDP Instructions
2/21
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1Table of Contents
IntroductionDescription...................................................................................................................................................1Applications ................................................................................................................................................2
DDP-1 ChassisDescription...................................................................................................................................................3Single Access............................................................................................................................................4-5Dual Access .................................................................................................................................................6Special Application ...................................................................................................................................7-8
DDP-1 CardsDescription...................................................................................................................................................9Ordering Information...................................................................................................................................9Schematics ...........................................................................................................................................10-12
DDP-1 BaysRack Assembly Guidelines .........................................................................................................................13Rack and Hardware Guidelines..................................................................................................................14System Line-Up..........................................................................................................................................15Rack and Hardware Ordering Information .................................................................................................16
Rack Accessories Ordering Information......................................................................................................16
Auxiliary Equipment .............................................................................................................................17Patch Cords..............................................................................................................................................17Index .......................................................................................................................................................18
7/31/2019 DDP Instructions
3/21
1w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1Introduction
The DDP-1 chassis is an interface pointplaced between a digital cross-connectsystem (DCS) and digital networkelements (NE), providing a flexiblealternative to hard wiring NEs directly
to the DCS.
A digital distribution point provides cabletermination and circuit access to digitalcircuits at the DS1, DS1C, E1 and VT1.5signal levels. Software cross-connectsbetween two NEs are provided by the DCS.
DS3
NE
DS3
NE
DS3
NE
DS3
NE
DDP-3
DS1
NE
DS1
NE
DS3PORT
DDP-1 3/3 DCS
DS3PORT
3/1 DCS
DS3PORT
DS3PORT
DS1PORT
DS1PORT
LOGICALCROSS-
CONNECTS
TWISTEDPAIR CABLE
COAXIALCABLE
Features and Benefits
Centralized termination, interconnection and access to digital circuits between the 3/1 DCS andnetwork elements
An alternative to hard wiring the digital telecommunications equipment directly to the 3/1 DCSbackplane
Smooth, flexible and economical migration of service to a 3/1 DCS in an office
In-service or out-of-service cutover options using DDP-1
Catastrophic access options utilizing the optional jack card (monitoring in both directions from onelocation and patching options)
Ease of adding or removing future network elements
Improved cable management and additional cabling flexibility as the office grows
Economic access solution since permanent jacks are not required for each circuit
7/31/2019 DDP Instructions
4/21
2w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1Applications
The DDP-1 is an interconnect point between a NE and a DCS port. When the DCS is installed, all circuitports are cabled to the DDP. Periodically, when NEs are added, they are cabled to the DDP instead of wiringto the active DCS backplane. Moving this routine cabling away from the DCS backplane reduces service out-ages of active circuits due to installation activities. The DDP-1 is an extension of the fragile DCS backplaneand provides a robust distribution frame for wiring of NEs as the telecommunications network evolves.
In addition to the basic application of an interface point between the DCS and NE, the DDP-1 may be usedas a termination and access point between dedicated NEs where cross-connect flexibility is not required,such as in outside plant cabinets, huts, CEVs and on customer premises. If cross-connect flexibility is desired,then a DSX-1 may be a more appropriate product.
Circuit access is provided by modular access cards that need only be plugged into a DDP-1 chassis whenaccess is desired. Access cards provide industry standard Bantam jacks (MONITOR, OUT and IN jacks) forconvenient monitoring, testing and patching capabilities. Patching into the OUT and IN jacks breaks the con-nection between the DCS and NE and extends the signal to a patch cord for testing and patching. TheMONITOR jack is a high impedance bridge point that is used for nonintrusive monitoring of active circuits.DDP-1 chassis are typically grouped together in a common area to concentrate installation and maintenanceactivities and allow for patching between any access point.
During normal circuit operation, the access cards are not in line with the circuit. The DDP-1 chassis includesmake-before-break loop-through connectors that interconnect a NE to a DCS port. When access is desired,the access card is inserted into the chassis where the loop-through connection is then extended through theaccess card.
M
O
I
M
O
I
DS1NE1
DS1PORT
A
DS1PORT
B
DS1NE2
DDP-1 POS #2
XMITRCV
XMIT
RCV
XMITRCV
XMITRCV
DDP-1 POS #1
SoftwareCross-Connects
DCS
7/31/2019 DDP Instructions
5/21
3w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 ChassisDescription
The DDP-1 chassis is available in two basic configurations: Single Access and Dual Access.
Various circuit densities are available to match DCS group quantities (i.e. 56, 64, 84 circuit). Various wiringconnection styles (i.e. wire-wrap, 50-pin or 64-pin connectors) and equipment rack styles (i.e. 19", 23"mounting) are available.
The Single Access chassis allows access to the NEside or the DCS side but not simultaneously. Anaccess card is inserted in the normal position (withmonitor jack on top) to access the NE. The accesscard is inserted in the inverted position (monitorjack on bottom) to access the DCS.
The Dual Access chassis allows access to both theNE side and the DCS side simultaneously. Twoaccess cards are inserted in the normal position(with monitor jack on top). One access card isinserted into the top half of the chassis for the NE,and another access card is inserted into the bottomhalf of the chassis for the DCS. Full bidirectionalaccess is accommodated with the dual access chassis.
M
O
I
I
O
M
DS1NE1
DS1PORT
A
DCS ACCESS
XMITRCV
XMITRCV
NE ACCESS
DCS
Software Cross-Connects to Other
DCS Ports
DS1
NE1
XMITRCV
Software Cross-
Connects to Other
DCS PortsConnections
Internal to Card
DS1
PORT
A
XMITRCV
M
O
I
M
O
I
DCS
NE
Single Access
Dual Access
DCS AccessNE Access
Software Cross-
Connects to OtherDCS Ports
Software Cross-
Connects to Other
DCS Ports
Connections
Internal to Card
7/31/2019 DDP Instructions
6/21
4w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 ChassisSingle Access
84 and 64 Termination
*Front or rear access to equipment cable terminations is designed to meet CEV or OSP cabinet requirements.
Note: Panel Color is Putty.
DD1-351001Front View
(Door Closed)
DD1-351001Front View
(Door Open)
DD1-351001Rear View
Number ofCircuits
84
84
64
64
Cable
ConnectionsDCS IN/OUT
Wire-wrap
Wire-wrap
Wire-wrap
64-PinReceptacle
Connectors
Cable
ConnectionsNE IN/OUT
Wire-wrap
Wire-wrap
Wire-wrap
Wire-wrap
O r d e r i n g I n f o r m a t i o n
Cable
TerminationAccess
Rear
Front or
Rear
Rear
Rear
MountingOptions
Flush or 2"
(5.08 cm)
RecessEIA/WECO
Flush
WECO
Flush or 2"
(5.08 cm)Recess
EIA/WECO
Flush or 2"(5.08 cm)
Recess
EIA/WECO
Dimensions(Height, Width, Depth)
6 x 23 x 8.4 inches
(15.24 x 58.42 x 21.34 cm)
6 x 23 x 8 inches
(15.24 x 58.42 x 20.32 cm)
2.6 x 23 x 8 inches
(6.6 x 58.42 x 20.32 cm)
3 x 23 x 11 inches
(7.62 x 58.42 x 27.94 cm)
Catalog Number
DD1-351001
DD1-351000*
DD1-321001
DD1-322001
6.0"
1.75"
22.3"
23.0"
DD1-351001Rear View
DD1-351001Front View
(Door Open)
7/31/2019 DDP Instructions
7/21
5w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 ChassisSingle Access
56 Termination
8.00"
2.00"
23.00"
22.31"
CKT 1 CKT 56
1.25"
1.25"2.6
DD1-311001
Front View
DD1-311001
Top View
DD1-331001
Front View
(Door Open)
DD1-331001
Front View
(Door Closed)
DD1-331001
Rear View
Note: Panel Color is Putty.
Number ofCircuits
56
56
Cable
ConnectionsDCS IN/OUT
Wire-wrap
Wire-wrap
Cable
ConnectionsNE IN/OUT
Wire-wrap
Wire-wrap
O r d e r i n g I n f o r m a t i o n
Cable
TerminationAccess
Rear
Rear
MountingOptions
Flush or 2"(5.08 cm)
Recess
EIA/WECO
4.75" (12.07
cm) Recess
EIA/WECO
Dimensions(Height, Width, Depth)
2.6 x 23 x 8 inches(6.60 x 58.42 x 20.32 cm)
3 x 19 x 11.5 inches(7.62 x 48.26 x 29.21 cm)
Catalog Number
DD1-311001
DD1-211001
7/31/2019 DDP Instructions
8/21
6w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 ChassisDual Access
56 and 64 Termination
8.20"
2.00"
.50"
5.00"
4.00"3.25"
1.00"
6.00"
23.00"
22.31"
CKT 1 CKT 64
DD1-331DAS
Front View
(Door Open)
DD1-331DAS
Top View
Note: Panel Color is Putty.
Number ofCircuits
64
56
Cable
ConnectionsDCS IN/OUT
Wire-wrap
Wire-wrap
Cable
ConnectionsNE IN/OUT
Wire-wrap
Wire-wrap
O r d e r i n g I n f o r m a t i o n
Cable
TerminationAccess
Rear
Rear
MountingOptions
Flush or 2"
(5.08 cm)Recess
EIA/WECO
5" (12.7 cm)
Recess
EIA/WECO
Dimensions(Height, Width, Depth)
6 x 23 x 8.2 inches
(15.24 x 58.42 x 20.83 cm)
6 x 19 x 10 inches
(15.24 x 48.26 x 25.40 cm)
Catalog Number
DD1-331DAS
DD1-241002
7/31/2019 DDP Instructions
9/21
7w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 ChassisSpecial Applications
*The DCS connections may be made with either DB15 or with RJ48X connectors since both are provided.
**Special labeling and location of cable terminations are designed to meet co-location requirements.
Note: Panel Color is Putty.
23.00"
22.31"
6.00"
.50"
5.00"
4.00"3.25"
1.00"
CKT 64CKT 1
DD1-331003 Front View
10.40"
2.00"
DD1-331003 Top View
Number of
Circuits
64 (Dual
Access)
56 (Single
Access)
4 (Single
Access)
Cable
ConnectionsNE IN/OUT
Wire-wrap
(Access 1)
Wire-wrap
(LEC-Front)
5' Stub End
Cable
Attached
(24GA/16PR,
8PR Unused)
O r d e r i n g I n f o r m a t i o n
CableConnectionsDCS IN/OUT
Wire-wrap
(Access 2)
Wire-wrap
(CAP-Rear)
Both DB15
Receptacleand RJ48X
Connector
Cable
Termination
Access
Rear
Front and
Rear
Rear
Mounting
Options
2" (5.08 cm)
RecessEIA/WECO
5" (12.7 cm)
RecessEIA/WECO
Wall Mount
Dimensions(Height, Width, Depth)
6 x 23 x 10.4 inches
(15.24 x 58.42 x 26.42 cm)
5 x 19 or 23 x 11.7 inches
(12.7 x 48.26 or 58.42 x 29.72 cm)
3 x 19 x 12.25 inches
(7.62 x 48.26 x 31.12 cm)
Catalog Number
DD1-331003**
DD1-211003**
DD1-000002*
7/31/2019 DDP Instructions
10/21
8w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 ChassisSpecial Applications
12.25"
5.00"
4.75"
DD1-212001
Top View
19.00"
18.31"
CKT 1 CKT 56
1.00"
1.00"
.480"
3.00"
DD1-212001Front View
Note: Panel Color is Putty.
Number of
Circuits
56
Cable
Connections
DCS IN/OUT
Wire-wrap
Cable
Connections
NE IN/OUT
Wire-wrap
O r d e r i n g I n f o r m a t i o n
Cable
Termination
Access
Rear
MountingOptions
4.75"
(12.07 cm)Recess
EIA/WECO
Dimensions(Height, Width, Depth)
3 x 19 x 12.25 inches
(7.62 x 48.26 x 31.12 cm)
Catalog Number
DD1-212001
7/31/2019 DDP Instructions
11/21
9w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 CardsDescription
Description
Loopback card
Provides loopback of transmit to receive for both the NE and DCS
equipment.
Terminating card
Provides 135 Ohm termination across tip and ring for transmit andreceive of both NE and DCS equipment.
Opening card
Provides opening of transmission path between NE and DCS.(Isolates NE from DCS for continuity testing during installation.)
Jack access cardProvides MON, OUT and IN jacks for circuit access to NE equipment.Provides MON, OUT and IN jacks for circuit access to DCS equipment
when the card is inverted. (Bantam jacks)
Drop and insert card
Provides MON, OUT and IN jacks for both the NE and DCS equipment
for full duplex circuit access. This provides dual access functionality in
the single access chassis. (Bantam jacks)
Circuit guard card
Provides circuit guard with red label for a single mounting slot withinthe chassis. This prevents insertion of an access card for high priority
circuits.
Monitor only card
Provides MON jack for circuit access to the NE equipment transmit.Provides MON jack for circuit access to the DCS equipment transmit
when the card is inverted. (Bantam jack)
DS0 access card
Provides jack access to voice frequency circuits when DDP-1 chassis is
used in special analog applications.
Start-up kit
Kit consists of: (28) Loopback, (4) Terminating, (4) Opening, (28) Jack
access, (4) Monitor only cards
Module extractor tool
Used to extract DDP-1 card from its mounting slot in the chassis
Catalog Number
DD1-100002
DD1-100003
DD1-100004
DD1-100005
DD1-100006
DD1-100008
DD1-100012
DD1-100020
DD1-100025
DD1-000001
Cards are inserted into the DDP-1 chassis only when equipment installation or maintenanceactivities are required. A variety of cards provide many functions during installation and mainte-nance activities. Each access card has a lock and release device for secure attachment in thechassis. All cards containing jacks use industry standard Bantam jacks.
O r d e r i n g I n f o r m a t i o n
7/31/2019 DDP Instructions
12/21
10w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 CardsSchematics
T
R
T
R
NE OUT
NE OUT
NE IN
NE IN
T
R
T
R
DCS IN
DCS IN
DCS OUT
DCS OUT
Loopback CardDD1-100002
T
R
T
R
T
R
T
R
NE OUT
NE OUT
NE IN
NE IN
DCS IN
DCS IN
DCS OUT
DCS OUT
R1
R1
R1
R1
Terminating Card
R1 = 135 Ohm
Opening Card
DD1-100004
T
R
T
R
T
R
T
R
NE OUT
NE OUT
NE IN
NE IN
DCS IN
DCS IN
DCS OUT
DCS OUT
DD1-100002
DD1-100004
DD1-100003DD1-100003
7/31/2019 DDP Instructions
13/21
11w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 CardsSchematics
DD1-100005
R
T
SG
R
RN
TN
T
TTN
RN
R
T (NE OUT)
R (NE OUT)
T (NE IN)
R (NE IN)
SLEEVE GROUND (COMMON BUS)
TN (DCS IN)
RN (DCS IN)
TN (DCS IN)
RN (DCS IN)
430 OHM
(NE) IN
100 OHM
(NE) OUT
MON
Jack Access Card DD1-100005
100 Ohm Normal Orientation
R
RN
TN
T
T
TN
RN
R
SG
T
R
R (DCS IN)
T (DCS IN)
R (DCS OUT)
T (DCS OUT)
SLEEVE GROUND (COMMON BUS)
TN (NE IN)
430 OHM
RN (NE IN)
TN (NE OUT)
RN (NE OUT)
(DCS) IN
(DCS) OUT
MON
100 OHM
Jack Access Card DD1-100005
100 Ohm Flipped Orientation*
DD1-100006
MON
OUT
IN
NTWK
100OHM
SLEEVEGROUND
NETWORK OUT
NETWORK IN
MON
OUT
IN
DCS
100OHM
SHIELDGROUND
DCS OUT
DCS IN
430 OHM
T
R
T
R
T
R
T
R
430 OHM
Drop and Insert DD1-100006
*Note: Tip and Ring are reversed in the Flipped Orientation
7/31/2019 DDP Instructions
14/21
12w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 CardsSchematics
RTSGRRNTNTT
TNRNR
T (NE OUT)
R (NE OUT)
T (NE IN)
R (NE IN)
SLEEVE GROUND (COMMON BUS)
TN (DCS IN)
RN (DCS IN)TN (DCS IN)
RN (DCS IN)
(NE) IN(PLUGGED)
100 OHM
430 OHM
(NE) OUT(PLUGGED)
MON
INSULATOR
DD1-100012 100 Ohm Monitor Only
Normal Orientation
R
RN
TN
TT
TN
RN
R
SG
T
R
R (DCS IN)
T (DCS IN)
R (DCS OUT)
T (DCS OUT)
SLEEVE GROUND (COMMON BUS)
TN (NE IN)RN (NE IN)
TN (NE IN)
RN (NE IN)
100 OHM
430 OHM
(DCS) IN(PLUGGED)
(DCS) OUT
(PLUGGED)
MON
DD1-100012 100 Ohm Monitor Only
Flipped Orientation*
DD1-100012
R
T
SG
R
RNTN
T
T
TN
RN
R
T (NE OUT)
R (NE OUT)
T (NE IN)
R (NE IN)
SLEEVE GROUND (COMMON BUS)
TN (DCS IN)
RN (DCS IN)
TN (DCS IN)
RN (DCS IN)
(NE) IN
(NE) OUT
MON
DD1-100020 DS0, Normal Orientation
DD1-100020 DS0, Flipped Orientation*
R
RNTN
T
T
TN
RN
R
SG
T
R
R (DCS IN)
T (DCS IN)
R (DCS OUT)
T (DCS OUT)
SLEEVE GROUND (COMMON BUS)
TN (NE IN)
RN (NE IN)
TN (NE OUT)
RN (NE OUT)
(DCS) IN
(DCS) OUT
MON
DD1-100020
*Note: Tip and Ring are reversed in the Flipped Orientation
7/31/2019 DDP Instructions
15/21
13w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 BaysRack Assembly Guidelines
The recommended bay layout consists of 16 chassis. Each chassis contains 56 or 64 circuits depending onthe type of DCS machine being interfaced. This rack configuration of 16 chassis provides an interface for896 circuits using the 56 circuit chassis or 1024 circuits using the 64 circuit chassis. The chassis are mountedin groups of four to match numerically to each DCS module of 224 or 256 circuits. Although there is physi-cal mounting space for more chassis, the rack is limited to these maximums for the following reasons:
10" spacing between racks has a maximum cable capacity for up to 1024 circuits using either 600-type(22 gauge) or 1249-type (26 gauge) shielded cable.
Often a configuration of 16 chassis corresponds numerically to the number of DS1 circuits in many DCSmachines. Example: 16 chassis x 56 circuits per chassis = 896 circuits per rack.
The unused mounting spaces in the rack can be used for maintenance equipment such as amiscellaneous jackfield (fault location lines, order wire access, T1 maintenance lines, etc.),communication panel, fuse panel and customer provided test equipment. A fuse panel is not requiredfor DDP-1, but is required if a communication panel or test equipment is placed in the DDP-1 rack.
The unused mounting spaces in the rack also provide room for future DDP-1 chassis when rolling over toa new DCS machine. DS1 ports from the new DCS can be terminated on the new chassis, then transferthe NE cables as they are cut into the new DCS.
CABLESUPPORTBRACKETSIN REAR
16
15
14
13
44
40
35
30
25
20
15
10
5
1
7'-0"
25.88
1,75
5.00
12.00
5.00
REAR
12
11
10
9
4
3
2
1
8
7
6
5
DDP-1 CHASSIS
Front View
Side View
7/31/2019 DDP Instructions
16/21
14w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 BaysRack and Hardware Guidelines
ADC recommends placing the DDP-1 in a 7' environment to allow technicians to access circuits without theneed for ladders. When DDP-1 is installed in environments higher than 7', the chassis should be placedonly up to the 7' level. This recommendation follows existing practices for access to DSX jacks.
Aisle spacing conforms to existing practices of 3'0" front aisle and 2'6" rear aisle spacing. This allows room
for technicians to perform routine maintenance activities at the front of racks and for cable termination atthe rear of racks.
Unequal flange-type racks are recommended because they provide efficient cable management for routingcables into the rack. When two racks are placed next to each other, the wide front flanges form a cableduct area between the racks. This duct area provides a cable management route for running cables vertical-ly within the rack. Adding a rack filler panel between the racks increases the cable duct area. For a full rackof DDP-1 (16 single access chassis), the recommended size of the filler panel is 10" between racks and 5"at the ends of rack lineups. This spacing provides sufficient room to add and remove cables as the networkelements (NE) and digital cross-connect system change (DCS).
END GUARD
5" FILLERPANEL
UNEQUAL FLANGERACK
10" FILLERPANEL
NE CABLETIE BRACKET
DCS CABLETIE BRACKET
7/31/2019 DDP Instructions
17/21
15w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 BaysSystem Line-Up
Guard boxes (included as part of the rack) provide a bumper at the base of the rack to prevent mobileequipment from hitting equipment chassis installed in the rack. The recommended unequal flange typerack is equipped with 5" rear and 2" front guard boxes. The DDP-1 chassis will fit within a 12" rack foot-print. A/C outlets may be placed on the guard boxes and are recommended for convenience on everythird or fourth rack.
Recommended end guards are placed at the ends of rack lineups to protect cables routed in the ductarea. They also provide a location for bay alarm indicators and A/C light switches.
The recommended rack installation kit provides hardware to anchor the rack to the floor and support thetop of the rack to superstructure above. Also included in the kit are cable tie brackets that attach to thesides of the rack in the duct area to provide a means to secure the DCS cables within the duct area.Twelve NE cable tie brackets attach to the rear of the rack's wide front flange. These brackets provide ameans to secure the NE cables in the same duct area and separate them from the DCS cables. The segre-gation between NE and DCS cable allows for efficient cable management as cables are added andremoved in the future. A three bay lineup with racks, filler panels, and end guards is shown below.
One group of fourDDP-1 chassis
interfaces to oneDCS module
DDP-1Rack #1
ENDGUARD
ENDGUARD
DDP-1Rack #2
DDP-1Rack #3
DCSRack #3
DCSRack #2DCSRack #1
5" FILLERPANEL
5" FILLER
PANEL
10" FILLER
PANEL
7/31/2019 DDP Instructions
18/21
16w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 Rack, Hardware and Accessories
Rack Accessories
Contact ADC at 1-800-366-3891 for preassembled DDP-1 bays.
O r d e r i n g I n f o r m a t i o n
Description
7' Rack and Hardware
7' x 23" network rack; 2" front/5" rear guard box, EIA, putty white
7' x 5" rack filler panel; putty white7' x 10" rack filler panel; putty white
7' x 12" universal end guard; putty white
9' Rack and Hardware
9' x 23" network rack; 2" front/5" rear guard box, EIA, putty white
9' x 5" rack filler panel; putty white
9' x 10" rack filler panel; putty white9' x 12" universal end guard; putty white
11'6" Rack and Hardware
11'6" x 23" network rack; 2" front/5" rear guard box, EIA, putty white
11'6" x 5" rack filler panel; putty white11'6" x 10" rack filler panel; putty white
11'6" x 12" universal end guard; putty white
Catalog Number
PWUEF-7ER1SE
7RFP-5NPW7RFP-10NPW
UEGP-7NPW
PWUEF-9ER1SE
9RFP-5NPW
9RFP-10NPW
UEGP-9NPW
PWUEF-115ER1SE
115RFP-5NPW115RFP-10NPW
UEGP-115NPW
O r d e r i n g I n f o r m a t i o n
Description
AC outlet; putty white (2 per rack where outlets are required)
AC raceway; putty white (2 per rack where outlets are not required)
AC raceway filler; putty white (2 per 5" filler panel, 4 per 10" filler panel)Rack Installation Kits
7' DDP Bays: Includes
(1) floor mounting kit
(1) top attachment kit for 7' rack
(12) rack tie bracket kits(12) DDP tie bracket kits
(1) rack ground kit for 7' rack
9' and 11'6" DDP Bays: Includes
(1) floor mounting kit
(1) top attachment kit for 7' rack
(12) rack tie bracket kits(12) DDP tie bracket kits
(1) rack ground kit for 9' and 11'6" racks
Catalog Number
ACOK-PWNB
ACB-PWNB
AC-PWNB-RS5
RINST-DDP7-PW
RINST-DDP9-PW
Rack and Hardware
7/31/2019 DDP Instructions
19/21
17w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
DDP-1 Auxiliary Equipment and Accessories
Three Conductor Patch Cords
Bantam patch cords are plastic jacketed,shielded cords with molded-on plugs. Theplugs are made with molded insulationbetween conductors. Bantam patch cordsare available with single and dual three con-ductor plugs. A cord strain relief feature isincluded in the plug construction. Dualtwisted pair patch cords are recommendedfor protection against cross talk, especiallyduring switch cutovers and when patchcords over 12' are used.
*For nickel plated patch cords, add the suffix N.
For plenum-rated fire retardant patch cords, add the suffix PL.
Bantam Three Conductor Patch Cords
Dual
Single
O r d e r i n g I n f o r m a t i o n
Description
1.75" x 23" blank panel; putty white3.50" x 23" blank panel; putty white
5.25" x 23" blank panel; putty white
Communication panelCommunication panel headset
Communication panel handset
Communication panel headset/handset holder
20 position fuse panel (1.75" x 19"); putty whiteExtender bracket kit for fuse panel (19" to 23"); putty white
Catalog Number
PWBP-1723PWBP-3523
PWBP-5223
COMP-21COMP-HDS
COMP-HNDS
COMP-HNR-P
DSX-FP20HEB-17P
O r d e r i n g I n f o r m a t i o n
Description
Three Conductor*Single
1' (.3 m)
2' (.61 m)3' (.91 m)
4' (1.22 m)
5' (1.52 m)6' (1.83 m)
8' (2.44 m)
10' (3.05 m)12' (3.66 m)15' (4.57 m)
20' (6.1 m)
Dual1' (.3 m)
2' (.61 m)
3' (.91 m)4' (1.22 m)
5' (1.52 m)
6' (1.83 m)
8' (2.44 m)10' (3.05 m)
12' (2.66 m)
14' (4.27 m)20' (6.1 m)
Catalog Number
PJ712
PJ714PJ716
PJ718
PJ720PJ722
PJ1208
PJ1210PJ1212PJ1415
PJ1420
PJ762
PJ764
PJ766PJ768
PJ770
PJ772PJ1308
PJ1310
PJ1312PJ1514
PJ1520
Auxiliary Equipment
7/31/2019 DDP Instructions
20/21
18w w w . a d c . c o m + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
1
0
/0
0
2
5
8
DDP-1
DigitalDistri
bution
Produc
ts
Index
115RFP-10NPW....................................................16115RFP-5NPW ......................................................167RFP-10NPW ........................................................167RFP-5NPW ..........................................................169RFP-10NPW ........................................................16
9RFP-5NPW ..........................................................16AAC-PWNB-RS5......................................................16ACB-PWNB...........................................................16ACOK-PWNB........................................................16CCOMP-21 .............................................................17COMP-HDS ..........................................................17COMP-HNDS ........................................................17COMP-HNR-P .......................................................17DDD1-000001 ..........................................................9DD1-000002 ..........................................................7
DD1-100002 ..........................................................9DD1-100003 ..........................................................9DD1-100004 ..........................................................9DD1-100005 ..........................................................9DD1-100006 ..........................................................9DD1-100008 ..........................................................9DD1-100012 ..........................................................9DD1-100020 ..........................................................9DD1-100025 ..........................................................9DD1-211001 ..........................................................5DD1-211003 ..........................................................7DD1-212001 ..........................................................8DD1-241002 ..........................................................6
DD1-311001 ..........................................................5DD1-321001 ..........................................................4DD1-322001 ..........................................................4DD1-331003 ..........................................................7DD1-331DAS..........................................................6DD1-351000 ..........................................................4DD1-351001 ..........................................................4DSX-FP20H...........................................................17EEB-17P..................................................................17PPJ1208 .................................................................17PJ1210 .................................................................17
PJ1212 .................................................................17PJ1308 .................................................................17PJ1310 .................................................................17PJ1312 .................................................................17PJ1415 .................................................................17PJ1420 .................................................................17PJ1514 .................................................................17PJ1520 .................................................................17PJ712....................................................................17
PJ714....................................................................17PJ716....................................................................17PJ718....................................................................17PJ720....................................................................17PJ722....................................................................17
PJ762....................................................................17PJ764....................................................................17PJ766....................................................................17PJ768....................................................................17PJ770....................................................................17PJ772....................................................................17PWBP-1723 ..........................................................17PWBP-3523 ..........................................................17PWBP-5223 ..........................................................17PWUEF-115ER1SE.................................................16PWUEF-7ER1SE.....................................................16PWUEF-9ER1SE.....................................................16R
RINST-DDP7-PW....................................................16RINST-DDP9-PW....................................................16UUEGP-115NPW.....................................................16UEGP-7NPW.........................................................16UEGP-9NPW.........................................................16
7/31/2019 DDP Instructions
21/21
ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101Specifications published here are current as of the date of publication of this document. Because we are continuously improving ourproducts, ADC reserves the right to change specifications without prior notice. At any time, you may verify product specifications by
contacting o r headq arters office in Minneapolis ADC Telecomm nications Inc ie s its patent portfolio as an important corporate
Web Site: www.adc.comFrom North America, Call Toll Free: 1-800-366-3891 Outside of North America: +1-952-938-8080 Fax: +1-952-946-3292
For a complete listing of ADC's global sales office locations, please refer to our web site.