www.bearmach.com Passionate about Land Rovers
A-Bar Soft Plastic
VUB501740
These bars offer robust vehicle protection as they are a steel frame construction covered in athick rubber coat to absorb impact. Easily fitted to all Defender models
Fitment with winch Defender
VUB501720 Fitment without winch Defender
Lamp Guard
BA 122
A stylish set of lamp guards of sturdy construction and black nylon coated. The front guardsare hinged for easy access to the lights for cleaning while the rear set are fixed. This set willprotect the lights all around your vehicle from flying debris and minor bumps withoutaffecting the lighting output. (Only two holes to be drilled in plastic front trim panel, notsuitable for use with Spare Wheel Carrier BA 132/132B)
Set of 4 Defender
Front Lamp Guards
BA 012
Slatted steel on edge to square frame. Finished in black nylon. Fixed by special bracket fixingon to lamp bezel. Will fit all models with headlights in wing.
Pair Defender
Deluxe Rear Lamp Guard
BA 012A
Slatted steel welded on edge to square frame. Finished in black nylon. Fixed by special bracketfixing on to lamp bezel. Matches style of BA 012
Pair Defender
Rear Lamp Guards
BA 012B
Matching style of BA 012
Set of 4 Defender
D e f e n d e r
22
Passionate about Land Rovers www.bearmach.com
Rear Lamp Guards (HCPU)
BA 012C
To fit high capacity pick up Matching style of BA 012
Pair Defender
Perspex Light Shields
BA 053
Manufactured in impact resistant flat acrylic sheet. Helps protect your lights from stone chips.Fitting utilises two existing bezel fixing screws and two extra screws where bezel plastic mustbe drilled.
Pair Defender
Side Step with Rubber Tread
BA 038B
BA 030A
All steel construction with a ribbed rubber tread plate and a rubber encased flat section outerframe. With strong chassis mounted brackets. Easy to install.
Pair
Pair
Defender 110
Defender 90
Side Step
BA 133B
The outer tube is black nylon coated and the chequer plate is available in either aluminiumfinish or black anodised finish.
Black Annodised (Pair) Defender 90
BA 133 Aluminium (Pair) Defender 90
Side Step and Sill Guard
BA 038
13/4" steel tube construction with aluminium anti-slip tread plate. With strong chassis mountedbrackets. Tubular edge is black nylon coated.
Pair Defender 110
BA 030 Pair Defender 90
D e f e n d e r
23
www.bearmach.com Passionate about Land Rovers
Fixed Rear Step
BA 172
Made from heavy gauge steel and bar, then plated to give an extra durable finish. No drillingrequired, bolts directly onto crossmember and can be used in conjunction with all towingattachments. (Drop plate not included)
Defender
Folding Step
MTC3084
A sturdy built step with convenient spring loaded action to help raise and lower the step.
Rear Defender 90/110
STC7631 Side Defender 90/110
Bumperettes
BA 090
Steel folded section construction with sturdy brackets. Black nylon coated. Bolts directly inplace of the existing grab handles and affords good protection. (4.5Kgs)
Defender
Heavy Duty Bumperettes
RRC2971
Made from heavy gauge steel and powder coated for durability. Drilling required tocrossmember.
Left Hand Defender
RRC2970 Right Hand Defender
Heavy Duty Bumperettes
BA 290G
Available black powder coated or galvanised. These are very practical and give your vehicle avery individual look. Now with extra chequer-plate tread.
Galvanised Defender
BA 290 Black Powder Coated Defender
D e f e n d e r
24
Passionate about Land Rovers www.bearmach.com
Tubular Bumperette
BA 090T
Heavy duty 1" tube construction complete with brackets. Available in 3 finishes. Bolts directlyin place of existing grab handles and affords good protection. (Must use jack extension (BA2140) when using standard vehicle jack. Will not fit with Spare Wheel Carrier BA 132).
Black Nylon Defender
Tubular Bumperette
BA 090G
Heavy duty 1" tube construction complete with brackets. Available in 3 finishes. Bolts directlyin place of existing grab handles and affords good protection. (Must use jack extension (BA2140) when using standard vehicle jack. Will not fit with Spare Wheel Carrier BA 132).
Galvanised Defender
Tubular Bumperette
BA 090S
Heavy duty 1" tube construction complete with brackets. Available in 3 finishes. Bolts directlyin place of existing grab handles and affords good protection. (Must use jack extension (BA2140) when using standard vehicle jack. Will not fit with Spare Wheel Carrier BA 132).
Stainless Steel Defender
Wheel Arch Extensions
BA 3720
These wheel arch extensions are suitable for 3 or 5 door Defenders. They are made from highimpact plastic and are almost unbreakable.
50mm Defender
Roof Spotlight Mounting Bar
BA 2910
Rugged looks and finished in satin black powder coat. 2" section tubing with laser cutmounting plates. Four mounting points are welded to the bar to fix most popular makes ofdriving lamps securely in position.
Defender
D e f e n d e r
25
www.bearmach.com Passionate about Land Rovers
Hi-Force Heater Grilles
BA 5900
Maunfactured in high-impactplastic and finished to give adurable and fashionable effect.
Defender
Satin Black - Pair
Hi-Force Heater Grilles
BA 5901
Maunfactured in high-impactplastic and finished to give adurable and fashionable effect.
Defender
Gloss Black - Pair
Hi-Force Heater Grilles
BA 5902
Maunfactured in high-impactplastic and finished to give adurable and fashionable effect.
Defender
Zambezi Silver - Pair
Hi-Force Heater Grilles
BA 5903
Maunfactured in high-impactplastic and finished to give adurable and fashionable effect.
Defender
Brunei Silver - Pair
Sport Side Grille - RH Only
BA 5920
The standard versions have blackfins and mesh, the premiumversions have silver fins and mesh.
Defender
Standard Black
Sport Side Grille - RH Only
BA 5921
The standard versions have blackfins and mesh, the premiumversions have silver fins and mesh.
Defender
Standard Brunei Silver
Sport Side Grille - RH Only
BA 5922
The standard versions have blackfins and mesh, the premiumversions have silver fins and mesh.
Defender
Premium Black
Sport Side Grille - RH Only
BA 5923
The standard versions have blackfins and mesh, the premiumversions have silver fins and mesh.
Defender
Premium Brunei Silver
Sport Side Grille - RH Only
BA 5924
The standard versions have blackfins and mesh, the premiumversions have silver fins and mesh.
Defender
Standard Zambezi Silver
Sport Side Grille - RH Only
BA 5925
The standard versions have blackfins and mesh, the premiumversions have silver fins and mesh.
Defender
Premium Zambezi Silver
D e f e n d e r
26
Passionate about Land Rovers www.bearmach.com
Facelift Kit
BA 3551
This 3 part grille and lamp surround set offers maximum airflow, strength and stylish goodlooks. Easy to fit with no drilling or specialist tools required. Manufactured in tough injectionmoulded ABS to automotive standards. Fits all models including air-con vehicles. (Land Roverbadge not included - if required please order BTR1047A)
Black with chrome mesh Defender
BA 3550 Black with black mesh Defender
Facelift Kit
BA 3553
This 3 part grille and lamp surround set offers maximum airflow, strength and stylish goodlooks. Easy to fit with no drilling or specialist tools required. Manufactured in tough injectionmoulded ABS to automotive standards. Fits all models including air-con vehicles. (Land Roverbadge not included - if required please order BTR1047A)
Silver with stainless steel mesh Defender
BA 3552 Silver with black mesh Defender
Sliding Window Kit Flange Fit
BA 182A
As OEM
Pair Defender 110
BA 181 Pair Defender 90
Exterior Mesh Grilles
BA 2880
These window grilles are the ideal answer you need serious protection to your vehicles backwindows for extreme off-roading or security reasons. Manufactured from pressed steel thesegrilles are easily screwed into position or rivetted for a more permanent solution. (5 Piece - allrear windows and rear side of station wagon)
5 Piece Defender
D e f e n d e r
27
Sport Side Vent Right Hand
BA 5926
Defender
Standard Java Black
Sport Side Vent Right Hand
BA 5927
Defender
Premium Java Black
www.bearmach.com Passionate about Land Rovers
Perspex Weather Shields
BA 2088A
Easily fits to front doors to stop rain penetration when on the move. Reduces draughts yet stillallows good ventilation. (The image displayed shows similar product fitted to a Freelander).
Front - Pair Defender
Side Mouldings
BA 0202A
No drilling required, provides excellent protection for your door and vehicle side.
Defender 110
BA 0202 Defender 90
Unbreakable Mirror
BR 1914UH
These mirrors are awesome! We drove a Defender 90 over the mirror and it did not break,even the casing remained intact. Ideal for off road.
Heated Defender
BR 1914U Defender
Mudflaps
RTC9479
Essential equipment to prevent damage from debris thrown up by the tyres and to minimisewater spray when driving on-road. Made from a flexible, hi-density rubber.
Front - Pair with fixings Defender
RTC4685 Front - Pair without fixings Defender
BR 3248 Rear - Single without fixings Defender
Spare Wheel Carrier
BA 132C
Sturdily mounted to the chassis to ensure minimum strain on rear door and hinges. Opens withrear door and can be used with our bumperettes.
Hard top (Not fixed to Door) Defender (2002 on)
BA 132B Soft top (Not fixed to Door) Defender (up to 02MY)
BA 132 Hard top Defender (up to 02MY)
D e f e n d e r
28
Passionate about Land Rovers www.bearmach.com
Diff Guard
BA 121
Easy to fit, applicable to all models with standard axles, zinc plated for corrosion resistance, nodrilling required.
Defender
Diff Guard
BA 125
Easy to fit, applicable to all models with standard axles, zinc plated for corrosion resistance, nodrilling required.
Defender (not suitable for 110 rear 02MY on)
Diff Guard Slider Type
BA 3136
A very heavy duty product made from 6mm steel to offer sturdy protection. Zinc plated toresist corrosion. Bolts directly to the diff mounting bolts to protect case as well as acting as aslider.
Rear Defender 90 (07MY)
BA 3133 Rear Defender 110 (02MY on)
Salisbury Axle Pan Diff Guard
BA 3129
5mm thick Diff Guard for the Salisbury axle is zinc and yellowed to resist corrosion and comescomplete with all necessary fixings and instructions.
Defender
Sump Guard
BA 083C
Made from heavy duty 7mm aluminium plate and with 6mm fixing brackets which are zinccoated for extra corrosion resistance. The aluminium plate has 9 vent holes (38mm dia) toallow for ventilation, and allow excess water to drain. Complies with EU regulation.
fitment with integral winchmounting BA 3093B)
Defender 90/110
BA 083 Defender 90/110
D e f e n d e r
29
www.bearmach.com Passionate about Land Rovers
Fuel Tank Guard
BA 3196
Manufactured in heavy duty 4mm thick, high grade sheet steel with a galvanised finish. Easyto fit, no drilling required, picks up on fuel tank mounting points.Will not fit with towbar.
Rear Defender 90 (TD5 )
BA 3195G Plastic Tank Defender 110 (07 on TD5)
Fuel Tank Guard
BA 3192
Manufactured in heavy duty 4mm thick, high grade steel with a galvanised finish. Easy to fit,no drilling required, picks up on fuel tank mounting points.
Defender 110 (up to 1998)
Fuel Tank Guard
BA 3199
Manufactured in heavy duty 4mm thick, high grade steel with a galvanised finish. Easy to fit,no drilling required, picks up on fuel tank mounting points.
Defender 90 (up to 1998)
Wingtop Strengthener
BA 113
Made from aluminium chequer plate. Not only do these enhance the appearance of yourvehicle but also allow you to step on the wing to gain access to the roof rack.
Long - 2mm - with vent hole All Defender models
BA 113-3 Long - 3mm - with vent hole All Defender models
BA 113B Long - 2mm - Black - with vent hole All Defender models
BA 113B-3 Long - 3mm - Black - with vent hole All Defender models
BA 113D Long - 3mm - with aerial hole Defender (07 on)
BA 113E Long - 3mm - Black - with aerial hole Defender (07 on)
BA 113F LHD Defender (07 on)
BA 113G LHD - Black Defender (07 on)
BA 108 Short - to vent only Defender
BA 108A Short Black Defender
D e f e n d e r
30
Passionate about Land Rovers www.bearmach.com
Bonnet Top Strengthener
BA 120D
Made from sturdy 3mm aluminium chequer plate, fits in to the recess of the Defender bonnetand will allow persons to step on the bonnet for access to the root rack.
Black Defender (2007 on)
BA 120C Aluminium Defender (2007 on)
BA 120B Black Defender
BA 120 Aluminium Defender
Wing Vent Covers
BA 3904
Vent covers to match Wing Top Strengtheners
Universal Side Vent - BlackCoated
Defender
BA 3903 LH Side Vent - Stainless Steel Defender
BA 3902 RH Side Vent -Stainless Steel Defender
BA 3901 Top Vent Black Coated Defender
BA 3900 Top Vent Stainless Steel Defender
Rear Wing Protector
BA 124
Made from aluminium chequer plate, these protect the lower part of the rear wing from stoneand gravel damage. The ideal finishing touch, and as fitted to limited edition vehicles,
2 mm Defender 90
BA 124-3 3 mm Defender 90
BA 124B 2 mm Defender 110
BA 124B-3 3 mm Defender 110
BA 124C 2 mm - Black Defender 90
BA 124C-3 3 mm - Black Defender 90
BA 124D 2 mm - Black Defender 110
BA 124D-3 3 mm - Black Defender 110
Rock Guards
BA 110G
Made from galvanised box section, specially for the off-road enthusiast. Replaces aluminiumsill and bolts directly onto chassis and is more than able to support the weight of the wholevehicle. The galvanised finish can be painted to match the colour of your vehicle.
Galvanised Defender 110
BA 110 Black Powder Coated Defender 110
BA 109G Galvanised Defender 90
BA 109 Black Powder Coated Defender 90
D e f e n d e r
31
www.bearmach.com Passionate about Land Rovers
Sill Guard
BA 126
Made from aluminium chequer plate, these protect the sills from scuffing while entering orleaving the vehicle, as well as stone chips and light off-road damage. Ideal finishing touch, andas fitted to Limited Edition vehicles.
2 mm Defender 90
BA 126-3 3 mm Defender 90
BA 126C 2 mm - Black Defender 90
BA 126C-3 3 mm - Black Defender 90
BA 127 2 mm Defender 110
BA 127-3 3 mm Defender 110
BA 127B 2 mm Defender 110
BA 127B-3 3 mm Defender 110
Rock Guards
Made from galvanised box section, specially for the off-road enthusiast. Replaces aluminiumsill and bolts directly onto chassis and is more than able to support the weight of the wholevehicle. The galvanised finish can be painted to match the colour of your vehicle.
BA 110TG Galvanised - Inc Jack Points Defender 110
BA 110T Black - Including Jack Points Defender 110
BA 109TG Galvanised - Inc Jack Points Defender 90
BA 109T Black - Including Jack Points Defender 90
Tree Fenders
BA 3692
Easily fitted to the rear side panels of all Defender models, these stylish bars offer protectionfrom those annoying scratches and dents from the undergrowth when green-laning.Manufactured in a heavy gauge tubular steel and black nylon coated (requires some drilling).
1250mm Long - Pair Defender 110
BA 3690 Pair Defender 90/110 CSW
Front Hoop
BA 2900
An aesthetic bar to give your vehicle a 'challenge' look. The bar bolts to the vehicle. Suitablefor mounting spotlights. Finished in black. (Note: This is not a roll-over bar, aesthetic purposesonly)
Defender
D e f e n d e r
32
Passionate about Land Rovers www.bearmach.com
Roll Bar (Not Competition)
BA 2005
Standard rollbar (body mounted). Bolted onto cappings. Manufactured in tubular steel 2"(50mm) diameter with 3.2mm wall thickness. MIG welded with heavy mounting plates. (NotA.R.C). Will also fit vehicle with standard canvas hood. (Supplied unpainted)
Defender
Rear Bulkhead Removal Bar
BA 2901
Enables the removal of the panel behind front seats on a Defender, giving more legroom andeasier access to the back of the vehicle.
Defender
Roof Rack with Foldaway ladder
BA 123A
This roof rack with fold away ladder is both stylish and functional. The rack is of very sturdyconstruction and is black coated. It is easily fitted to the gutters using the fixings provided. Theladder folds down from the rear for easy access and folds back up to remain unobtrusive whennot in use. Will fit all models, clears sun roofs and tropical roofs on Series vehicles. Note: Theladder mounts on the left side not the right as shown in the images.
Extension - for fitment toLWB vehicles
Defender
BA 123 Defender
One Piece Roof Rack
BA 017
Manufactured from 3/4" box section steel. Jig welded and with a Galvanised finish. Clamp ongutter fixings. (Weight 26Kgs 88" / 30Kgs 109+110")
Defender 130/110 Crew Cab
BA 008A Defender 110
BA 007A Defender 90
Flat Pack Roof Rack
BA 008
Same appearance and manufacture as BA 007/8A but arrives flat pack for self assembly.
Defender 110
BA 007 Defender 90
D e f e n d e r
33
www.bearmach.com Passionate about Land Rovers
Optional Ladder
BA 010
Optional ladder for above roof racks, similar construction as the roof racks and is easily fittedto the back of the vehicle allowing easier access to lift loads to the roof rack. It is fitted to theleft of the rear door.
Suits BA 007/8/7A/8A All
Roof Rack "G4"
BA 3191
Heavy Duty tubular roof rack finished in black nylon coating O.E. Quality (Will not fit with rollcages). (The decking, lights and ladder not included)
Defender 110
BA 3190 Defender 90
Ladder Racks
BA 043
Sold in pairs, ideal for carrying unwieldy items such as ladders etc.
Standard - Pair Defender
BA 3100 Heavy Duty - Pair Defender
Towbar
STC50257
Bosal range of towbars have specification enhancements to ensure reliability and safety. Theseare high qulaity, TUV approved tow bars and are supplied with all necessary nuts and bolts,fitting instructions and safety guidelines. With height adjustment facility to maintain a leveltowing load.
Not Including Towball Defender 130 (1998 on)
VUB105470 Including Towball Defender 110 (1998 on)
Tow Plate
BA 183
A basic yet sturdy constructed non-adjustable tow plate, finished in black. (Towball notincluded)
Defender 90/110 (upto 1998)
D e f e n d e r
34
Passionate about Land Rovers www.bearmach.com
Adjustable Tow Hitch
BA 192B
Sturdily constructed adjustable tow hitch. Can be adjusted to five different heights. (Tow ballnot included)
E-Marked Defender 110 (from 1998)
BA 192A E-Marked Defender 90 (from 1998)
BA 192 E-Marked Defender 90/110 (upto 1998)
Front Tow Hitch
BA 3107
Quick fit tow hitch, fits in seconds. Simply slip over the front bumper of your vehicle andtighten the two wing nut bolts for instant towing capabilities. (Tow ball not included)
Removable Defender
Electric Wiring Kit
YWJ101500 N-Type wiring kit which clips into existingharness
Defender (1998 on)
BA 195A Universal towing bypass relay Defender
BA 195 Universal wiring kit with audible warning Defender
Tubular Winch Bumper with "A" Bar
BA 5676AC
Manufactured in heavy gauge tubular and plate steel, black powder coated. Integral bashplate and jacking points to take standard hi-lift jacks. The winch mounting plate will take themajority of modern winches with no further drilling, however some cutting of grille mayberequired, it wil accomodate both low and high line winches. All necessary hardware for fixingare included.
Black with Silver Bash-Plate Defender (with Air-con)
BA 5676A Black with Silver Bash-Plate Defender (with Air-con)
BA 5675AC Silver with Black Bash-Plate Defender (Non Air-Con)
BA 5675A Silver with Black Bash-Plate Defender (Non Air-Con)
Tubular Winch Bumper (No "A" Bar)
BA 5676C
Manufactured in heavy gauge tubular and plate steel, black powder coated. Integral bashplate and jacking points to take standard hi-lift jacks. The winch mounting plate will take themajority of modern winches with no further drilling, however some cutting of grille mayberequired, it wil accomodate both low and high line winches. All necessary hardware for fixingare included.
Black with Silver Bash-Plate Defender (with Air-Con)
BA 5676 Black with Silver Bash-Plate Defender (Non Air-Con)
BA 5675 Silver with Black Bash-Plate Defender (Non Air-Con)
D e f e n d e r
35
www.bearmach.com Passionate about Land Rovers
Towing Eye
BA 5683
To Suit Tubular winch bumpersBA 5675ABA 5675ACBA 5676ABA 5676ACBA 5675BA 5676BA 5676C
Defender
Winch Bumper
BA 3093B
Winch frame and integral bumper. Replaces the existing bumper. Black powder coated finish.No drilling or any modifications required. Incorporating jacking points. Made from 6mm steelplate. Will also fit air-con vehicles - please confirm vehicle type when orderingfitment of the following winches:(Warn 6000/8000 "M" and "MX" Series - Warn XD9000 - Superwinch X6 CD/X9 - T-Max
Defender
Winch Bumper
BA 3193
fitment of winches - BA 035/036
Defender
Winch Plate (Chassis Mounted)
BA 2028B
Chassis mounted winch plate to suit Defender, mounts on top of bumper.
to suit BA 2603 Defender (Non Air-Con)
BA 2028A to suit T-Max winches 11,000and 12,000
Defender (Non Air-Con)
BA 2030 to suit BA 035/036 Defender (Non Air-Con)
BA 2028 6,000lb, 8,000lb, 9,000lb,9,500lb T-Max winches.
Defender (Non Air-Con)
Cranked Rear Trailing Arm.
BA 3655
For use with suspension lifts. Includes rear polyurethene bushes.
Defender
D e f e n d e r
36
Passionate about Land Rovers www.bearmach.com
Front Radius Arm
BA 3672
The radius arms are for improved off-road use. Available in standard, 3°or 6° cambercorrection - for use with lift kits. Bushes not included.
6°Wide Defender
BA 3671R 3° Wide. (Replacement Version) Defender
BA 3671 3° Wide. Defender
BA 3670 Std Wide. Defender
Heavy Duty Adjustable Panhard Rod
BA 3666
Designed to correct axle position when vehicle has had a suspension lift.
Defender
Adjustable Panhard Rod
BA 3668 RHD Defender
BA 3667 LHD Defender
Rear Rose Suspension Arm
BA 3676
For the maximum axle articulation these rose jointed trailing arms are the latest products.Supplied with boots for maximum protection against mud and the elements. Will fit exisitngaxle and chassis without further modification.
Defender
Rear Shock Dropper
BA 3656
For lifted vehicles using standard shock absorbers to gain extra axle travel with minimumalterations.
Defender
D e f e n d e r
37
www.bearmach.com Passionate about Land Rovers
Rear Dislocation Cones
BA 3653 Pair Defender 110
Front Dislocation Cones
BA 3650 Pair Defender
Rear Dislocation Cones
BA 3651 Pair Defender
Front Spring Retainer Plate
BA 3652 Each Defender
Rear Spring Retainer Plate
NTC6106 Each Defender
D e f e n d e r
38
Passionate about Land Rovers www.bearmach.com
Single Tubular Shock Tower
BA 2156S
These new twin shock absorber brackets will suit all coil sprung models. The front unit consistsof top bracket, to take the original shock absorber plus an additional one, and the bottombracket to support the additional shock absorber. The rear unit consists of top shock absorberbrackets which weld onto the axle case. (When fitting to ABS vehicles a certain amount ofmodification will be required to move the ABS pump and pipes.
Front - Short - Galvanised Defender
BA 2156 Front - Galvanised Defender
Twin Shock Mount
BA 2158
These new twin shock absorber brackets will suit all coil sprung models. The front unit consistsof top bracket, to take the original shock absorber plus an additional one, and the bottombracket to support the additional shock absorber. The rear unit consists of top shock absorberbrackets which weld onto the axle case. (When fitting to ABS vehicles a certain amount ofmodification will be required to move the ABS pump and pipes.
Rear Defender
BA 2157S Front Short Defender
BA 2157 Front Defender
Caster Bush Kit
BSC 206PC
Caster bushes allow the axles to remain in their original positions when raising the vehicle (i.e.Prevents them twisting). They fit into the radius arms to minimise any stress on steeringcomponents.
Defender (from 1994)
BSC 202PC Defender (up to 1994)
Rear Anti Roll Bar
Replaces the original and yet is a more heavy duty construction. Improves the handling of yourvehicle.
Defender 110 (1994-98)
BA 2220 Defender 90 (1994 on)
Air Adjustable Suspension Aid
BA 2164
Designed to fit inside your rear coil springs. Can be inflated to a maximum of 25psi tomaintain the vehicles carrying capacity without spring sag. No need for expensive spring mods.Kit contains PolyAir cells, inflation line, and cell seats. Ideal for towing and eliminates bodyroll.
Defender 110
BA 2163 Defender 90
D e f e n d e r
39
www.bearmach.com Passionate about Land Rovers
Compressor Kit
BA 2163A
Vehicle mounted to enable you to inflate or deflate the air springs. Complete with all pipes,low pressure switch etc.
Defender
Front Mounted Intercooler.
BA 2320
Recommended for use with upgraded vehicles - Vehicle should be tuned to gain maximumperformance after intercooler is added.
Defender (200/300TDi-Not TD5)
Replacement Intercooler
BA 2306
These fit in place of the existing original units. They allow the air to be cooled by an extra50% for a denser charge and result in up to 25% increase in power.
Defender (TD5)
BA 2303 Defender (300TDi)
BA 2300 Defender (200TDi)
Silicone and Stainless Turbo Hose Kit
BA 2312
Includes all necessary components to replace all existing hoses. Fits with standard and upratedintercoolers.
Defender (300TDi)
BA 2310 Defender (200TDi)
Replacement Silicone Turbo Hoses.
BA 2334
Replaces original hoses only. Fits standard and uprated intercoolers.
Some vehicles may requireshortening one hose
Defender (TD5)
BA 2332 Defender (300TDi)
BA 2330 Defender (200TDi)
D e f e n d e r
40
Passionate about Land Rovers www.bearmach.com
EGR Blanking Kit
BA 2332A
Removes the mechanical EGR system from 300TDi or TD5, giving improved performance andfuel economy.
Defender (300TDi)
EGR Blanking Kit
BA 2336
Removes the mechanical EGR system from 300TDi or TD5, giving improved performance andfuel economy.
Defender (TD5)
Heater Matrix
BA 2380
This aluminium high output heater matrix increases cabin heat by 20%, two types available toreplace original part numbers.
Horizontal facing pipes Defender
BA 2370 Downward facing pipes Defender
Expansion Tank
BA 2324
This cooling system expansion tank is manufactured in aluminium for strength and durability.(Directly replaces original ESR63 plastic tank)
Defender
Power Steering Reservoir
BA 2323
Manufactured in aluminium for strength and durability - this power steering reservoir is adirect replacement for the original.
Defender
D e f e n d e r
41
www.bearmach.com Passionate about Land Rovers
Composite Head Gasket
ETC7819C 1.2mm thick Defender (V8 3.9/4.2)
BR 3178C Defender (V8 3.5)
Performance Flywheel
BA 2031
These lightweight performance flywheels come balanced and ready to fit to your tuned V8engine. (uses 9½" Clutch STC8358)
Defender (V8)
Heavy Duty Clutch Release Bearing
BR 2295M
The metal sleeved clutch release bearing uses the older specification clutch bearing and ametal sleeve to provide increased durability.
Defender
Stainless Steel Intermediate Pipe
BA 2269
Centre exhaust pipe (silencer removed) in stainless steel.
Defender 90 (200TDi)
BA 2267 Defender 90 (300TDi - upto TA)
BA 2267A Defender 90 (300TDi - VA on)
BA 2265 Defender 90 (TD5)
BA 2262 Defender (V8)
BA 2290 Defender 110 (200TDi)
BA 2268 Defender 110 (300TDi)
BA 2266 Defender 110 (TD5)
D e f e n d e r
42
Passionate about Land Rovers www.bearmach.com
V8 Performance Stainless Steel Exhaust
BA 2192A
This stainless steel exhaust will improve overall performance of V8 engines and is suppliedcomplete with extractor manifolds. Slightly more expensive than a standard exhaust but wellworth the initial expense. (Includes branches)
Defender 110 (3.5 Sports system)
BA 2192 Defender 90 (Carb models only)
Camshaft (+18-22BHP)
BA 2186
Designed to increase engine power. Camshaft only
Defender (V8 3.5/3.9)
Performance Crankshaft Drive Train Kit
BA 2179
Consists of forged cam gear, crank gear and heavy duty timing chain. (Does not includecamshaft)
Defender (V8 3.5/3.9)
Performance Chip (Power +33HP - Torque +65Nm)
BA 21782
Power upgrade chip for diesel engine. Easy to fit, just plug in and drive away. Benefit fromimprovements to power, torque and efficiency
Defender PUMA
BA 2178 Defender TD5
Distributor Waterproofing Kit (V8)
BA 2840
Everything you need to protect the distributor from damp conditions. Includes boots for coiland distributor.
Defender (V8)
D e f e n d e r
43
www.bearmach.com Passionate about Land Rovers
Twin Choke Performance Carburettor
BR 2230
The kit is fitted with Webcon's new Sync Link kit allowing synchronous opening of the Weber32/36 DGV throttle butterflies. This greatly enhances low speed driveability and torque,essential for off road driving. This kit wil fit all engines fitted with a tubular exhaust manifold.If the orginal exhaust manifold is still fitted, a simple 4 hole blanking plate will need to befabricated to block the aperture left when the OE intake manifold is removed.A Twin chokeperformance carburettor kit for Land Rover 2 1/4ltr Engines - Synchronous opening of theWeber 32/36 DGV throttle butterflies - Enhances low speed driveability and torque - Fits allengines with a tubular exhaust manifold - Includes manifold.
Defender
D e f e n d e r
44
Mallory Unilite Distributor
BA 5050
Accurate timing thats maintenance free. These Mallory Unilite distributors give you accurate,maintenance free ignition timing. Instead of old-fashioned points systems, they have photo-optic LED triggering systems that never vary or wear out. You get increased RPM potential, improved combustion, longer spark plug life, and bettercold-weather starting. Hooking one up is a simple 3-wire connection, and they come with your choice of adjustablemechanical and/or vacuum advance, self-lubricating bushings, and a Super-Duty cap and rotor.(Mallory Distributor Ballast should be fitted with distributor)
Mallory Unilite Distributor Defender
BA 5051 Replacement Cap Defender
BA 5052 Replacement Arm Defender
BA 5053 Replacement Module Defender
BA 5054 Ballast Defender
Carburettor and Induction Manifold Conversion For Rover 3.5 V8
BR 2236
Suitable for Rover V8 vehicles equipped with S.U. Or Stromberg carburettors from 1970-1987.This kit features Weber 4 barrel downdraught carburettors and dual plane induction manifold.The conversion has been developed for improved engine torque and fuel economy. Although calibrated for Range Rover 3.5 models, it is also suitable for many other Rover V8applications, and for those wishing to carry out engine tuning modifications. For applications other than Range Rover 3.5 models, calibration changes/adjustments may benecessary. This conversion can be carried out by a competent D.I.Y. mechanic (with basic tool kit), andcomes complete with detailed fitting instructions, covering various models. The kit comprises of:Carburettor; Manifold; Air Filter; Throttle linkage*; Fuel line connections/Fuel Filter; Engine
breather/pulse air system; Hose connections; All necessary gaskets, seals and fixtures.*Automatic transmission vehicles will require supplementary kick down linkage kit - PartNumber BR 2236A.Automatic transmission vehicles will require this supplementary kick down linkage kit.
Defender
BR 2236A Kick Down Kit Defender
BR 2236R Needle Valve Conversion Kit Defender
Off Road Use
BR 2236F Replacement Air Filter Defender
Passionate about Land Rovers www.bearmach.com
Detroit Locker (inc Carrier)*
BA 208
The Detroit Locker is a fully automatic locking traction differential that is well known forpremium performance and dependable operation. Preload devices between the side gearsdeliver 100% torque and power to both drive wheels yet unlock automatically to permitnecessary wheel speed differentiation. The Detroit Locker is trouble-free as it does not requireservice adjustments or special lubricants. Easy to install, no special tools or case modificationsrequired. One year Limited Warranty. (*Please specify spline type when orering)
Salisbury Diff. No Spin, replaces Sun Gears* Defender
BA 207A Rover Diff - 24 Spline Defender
BA 207 Rover Diff - 10 Spline Defender
TrueTrac Diff Locker
BA 209
This unit features a gear-type limited slip design (no clutch or friction plates to wear out). Itspositive gear action automatically splits the torque with none of the steering problemsassociated with other traction "diffs". Power transfer is so smooth that it is unnoticeablethrough the steering wheel when fitted in front drive steering axles. It performs as a standarddifferential on normal highway driving - then automatically engages when needed in wet,muddy or icy conditions.
Rover Diff -10 Spline Rear Defender
BA 209F Rover Diff -10 Spline Rear Defender
BA 209A Rover Diff - 24 Spline Rear Defender
BA 209AF Rover Diff - 24 Spline Front Defender
BA 209S Salisbury Diff Defender
ARB Air Locker to suit Rover Differential
BA 204
A manually lockable differential which is operated at the driver's discretion by the push of abutton. Locking and unlocking of the "diff" is extremely rapid and can be achieved at anyvehicle speed. Installation invloves a bolt in replacement of the original equipment differentialcentre, an air compressor and in-vehicle switch. Can be fitted to both front and rear axleswithout compromising on road performance. *Please Specify Spline type when ordering . Note: All A.R.B. Diff Lockers require compressor which is available seperately, order ref-BA 215
Rover Diff Defender 110-2002 on Inc Puma
BA 205 Rover Diff - 10 Spline Defender
BA 205A Rover Diff - 24 Spline Defender
BA 206 Salisbury - Rear Defender 110 (upto 2002)
D e f e n d e r
45
www.bearmach.com Passionate about Land Rovers
ARB Compressor
BA 215
To Suit A.R.B Diff Lockers
Defender
Crown Wheel and Pinion
BA 5700A
Crown wheel and pinion, suitable for off-road use where high ratio (low speed)manouevrability is required. Replaces standard set version on fine spline axles. May require aspacer ring for other applications.
4.1 Salisbury Diff Defender
BA 5700F 4.12 Front Defender
BA 5700 4.12 Rear Defender
Heavy Duty Driving Member
FTC859AN
Heavy Duty Driving Members with screw on dust cap. Direct replacement for original memberwith superior material specification, and longer splines.
Spare Nut Defender
FTC859A Inc Nut Defender
BR 0465A FRC5806A Defender
Heavy Duty Adjustable Ball Joint
TRE 76RS
Adjustable rear differential ball joint. Just take up the slack as it wears. Supplied withoutgaiter (Part Number 572338).
Defender
Quick Ratio Steering Box
BA 226
2.9 turns lock to lock. These steering boxes offer a quicker response when needing to turn tofull lock.
LHD Defender
BA 225 RHD Defender
D e f e n d e r
46
Passionate about Land Rovers www.bearmach.com
Heavy Duty Steel Track Rods.
BA 220
These steel track rods are rally proven. Ideal for the off-road enthusiast and come completewith BM greaseable ball joints. Features: No steering damper required. The heavy steel takesstress off the ball joints. Rods and joints last longer.
Defender
Free Wheeling Hubs
BR 1276A
Ideal economy measure when four wheel drive is not required, saves wear and tear on frontaxle. Includes conversion for transfer box
Pair Defender 110 (1994 on - exceptfactory fit Alloy Wheels)
BR 1276 Pair Defender 110 (1994)
Wheel Adaptor Set
BA 3413
To convert the stud pattern of the wheels fitted to your vehicle to allow fitment of differentwheels.
Defender to P38 Defender
Wheel Adaptor Set
BA 3415
To convert the stud pattern of the wheels fitted to your vehicle to allow fitment of differentwheels.
Defender to L322 Defender
Wheel Spacers
BA 3410
Kit of 4 spacers in alloy with all studs and nuts.
30mm Defender
D e f e n d e r
47
www.bearmach.com Passionate about Land Rovers
Performance Brake Pads
BA 2197
All pads are supplied in sets all fitted with anti-squeal pads and sensor wires (which may beremoved if not required) - No squealing - Less wear on brake discs - 30% improvement inbraking performance
Front -STC9150K Defender
BA 2198 Rear - STC1276K Defender
BA 2199 Front - STC2956K Defender
BA 2200 Rear - STC1601K Defender 110
BA 2201 STC2950K Defender
BA 2202 STC1275K Defender
Slotted and Drilled Brake Discs
BA 1608
These ultra heavy duty rotors offer additional durability and improved stopping power.Designed with Police, Ambulance and Military in mind, these brake discs are directionallyslotted (left/right) - Increase pad bite - Reduces fade - Delivers exceptional braking perfomance
Rear Solid - SDB000330S Defender 110 (2000 on)
BA 2205 Rear Solid - FTC1381S Defender
BA 2204 Front Vented - FTC902S Defender
BA 2203 Rear Solid - FTC7329S Defender 110 (1994-2000)
BA 2203 Front Solid - FRC7329S Defender (front solid)
Braided Brake Hose
Braided Stainless Steel Brake Hoses are available to replace the standard rubber flexible hosesand offer a more durable alternative. TUV approved.
BA 164AL +50mm Defender (2004 on - ABS - Inc Puma)
BA 164A Std Length Defender (2004 on - ABS - Inc Puma)
BA 164L +50mm Defender 90/110 (1999-2004MY - ABS)
BA 164 Std Length Defender 90/110 (1999-2004MY - ABS)
BA 161L +50mm Defender 110
BA 161 Std Length Defender 110
BA 159L +50mm Defender 90/110 (1999-2004MY Non ABS)
BA 159 Std Length Defender 90/110 (1999-2004MY Non ABS)
BA 158L +50mm Defender 90
BA 158 Std Length Defender 90
D e f e n d e r
48
Passionate about Land Rovers www.bearmach.com
Crystal Light Conversion Kit
BA 070C
Non 'E' Marked. Only Suitable for RHD Vehicles (Also available BA 070 and BA 070AHA Conversion Kits 'E' Marked)
H4 Unit - Non E Marked Defender
Crystal Light Conversion Kit
BA 070CA H4 Unit - E Marked (LHD) Defender
Crystal Light Conversion Kit
BA 070CB H4 Unit E Marked (RHD) Defender
LED Halo Light Set Ion Lens
BA 070HI
Non 'E' Marked. Only Suitable for RHD Vehicles (Also available BA 070 and BA 070AHA Conversion Kits 'E' Marked)
Halo Ions Gold Effect H4 Defender
LED Halo Light Set Crystal
BA 070HC
Non 'E' Marked. Only Suitable for RHD Vehicles (Also available BA 070 and BA 070AHA Conversion Kits 'E' Marked)
Clear H4 Unit Defender
D e f e n d e r
49
www.bearmach.com Passionate about Land Rovers
Headlamp Conversion Kit
BA 070
E'-Marked
Halo H4 (RHD) Defender
Headlamp Conversion Kit
BA 070A
E'-Marked
Halo H4 (LHD) Defender
Angel Eye Side Lights
BA 3037
The ideal addition for those requiring front fog lights, or can be used to upgrade the existinglights. The Halo can be used as a side light, replacing the original. Some modification of thepositioning is required on Defenders.
Defender
Rear Screen Washer Kit
BA 074
Rear door washer kit.
Defender
Single Electric Fan Kit
BA 031T
The electric fan kit replaces the belt driven unit. Simply remove fan from water pump hub,then fix electric fan through radiator with special fixings.
Replacement Thermostat to suit above
BA 031K Replacement Fitting Kit to suit above
BA 031 Defender
D e f e n d e r
50
Passionate about Land Rovers www.bearmach.com
Primary Double Electric Fan Kit, for extra cooling
BA 031T
The electric fan kit replaces the belt driven unit. Simply remove fan from water pump hub,then fix electric fan through radiator with special fixings.
Replacement Thermostat to suit above
BA 031K Replacement Fitting Kit to suit above
BA 031A Defender
Lumenition Kits
BA 138
Do away with the points and replace with breakerless ignition system for increased efficiencyand accurate tuning.
Defender (4 Cylinder - Lucasdistributor)
BA 137 Defender (V8)
Ignition Module
BA 140
Do away with the points and replace with breakerless ignition system for increased efficiencyand accurate tuning.
Defender
Radiator Muff
BA 2004
These high quality radiator muffs feature a two position adjustable flap to allow control of airflow to the radiator to suit different weather conditions.
Defender
Dog Guard
BA 076/2
50mm mesh, welded to a sturdy box section frame. Minimum effort required to install andeasily removed by two thumb wheels when not in use. Can be used as gun rack support andacts as a cargo load divider. Black Nylon Coated.
Defender 90/110
D e f e n d e r
51
www.bearmach.com Passionate about Land Rovers
Dog Guard (To fit Station Wagon) (OEM)
BA 091
50mm mesh welded to box section frame. Black nylon coated. Specially designed for ease ofinstallation, no drilling required. Floor to roof fitting offers protection to back of seats.
Defender 110 (SW)
Gun Rack
BA 087
Easy clip on installation to dog guard. Supplied as pairs these clips allow 3 guns or umbrellas tobe carried one above the other.
to fit BA 076/2 + BA 091 Defender
Rear Window Mesh Guard
BA 2170
For added security this set of window guards is constructed from a sturdy metal grid, blacknylon coated. Covers rear door window and the two rear quarter panels.
Set of 3 Defender
Standard Cubby Box
BA 189AG
Padded lid with brass hinges and locking stay. Trimmed with a black vinyl finish.
Grey Vinyl Defender
BA 189A Black Vinyl Defender
Optional Cup Holder
BA 189C for BA 189A Defender
D e f e n d e r
52
Passionate about Land Rovers www.bearmach.com
Lockable Cubby Box
BA 2421
Sturdy metal construction this lockable cubby box keeps valuables secure and from pryingeyes. Replaces the middle seat, the leatherette covered lid is a useful armrest.
Grey Defender
BA 2420 Black Defender
Instrument Surrounds
BA 2700
A unique set of products designed to add a touch of style to the interior of Defender90/110/130 vehicles. They offer a stylish upgrade to existing trim, quick and easy to fit. Allitems are manufactured in aluminium, hand finished in a highly polished finish.
Aluminium Heater Vents-Pair
BA 2701 Heater and Fan Control Handles - Set of 3
BA 2702 Clock Surrounds - Set of 4
BA 2703 Clock Surrounds - Set of 4
BA 2705 Centre Panel with Cigarette Lighter Surround
BA 2706 Centre Panel with Cigarette Lighter, Wiper and Gauge.
BA 2707 Centre Panel with Cigarette Lighter, Wiper and Headlight.
BA 2708 3 Gauges
BA 2709 Switch Panel
Interior Trim
BA 3840
A unique set of products designed to add a touch of style to the interior of Defender90/110/130 vehicles. They offer a stylish upgrade to existing trim, quick and easy to fit. Allitems are manufactured in aluminium, hand finished in a highly polished finish.
Gear Knob - for R380 Gearbox Only
BA 3841 Gear Knob - Aluminium - Transfer Box
BA 3846 Gear Knob - for LT77 Gearbox Only
BA 2710 Door Pull Surround
BA 2711 Window Winder Surround
BA 2712 Door Handle Surround
BA 3842 Door Locking Pegs
BA 3843 Door Closing Handles
BA 3844 Seat Reclining Handles
BA 3845 Air Vent Knobs Defender - 2002 on
D e f e n d e r
53
www.bearmach.com Passionate about Land Rovers
Rev Counter
RRC5231
These rev counters are designed for all models - petrol and diesel, including the TD5 (Directreplacement as OE)
Defender (up to 1998 V8+Tdiand others)
YAE100800 Defender (1998 on - V8 / Tdi)
YAE100790 Defender (1998 on TD5)
Air Conditioning Kits
BA 5006
Experience the convenience and comfort of air-conditoning in your Defender. These kits arecomplete with full instructions and all necessary fittings. Mounts as original with the exceptionof not having the extended front grille. Will also work with most heavy duty intercoolers.
Defender Puma 07 on
BA 5004 Defender (TD5 LHD)
BA 5003 Defender (TD5 RHD)
BA 5002 Defender (300TDi LHD)
BA 5001 Defender (300TDi RHD)
3 Point Safety Harness
BA 2154
Ideal for competition use or for that added safety. Mounts on lower fixings, top mount willneed to be repositioned in vehicle.
Defender
Lap Belt
BA 187
3 point cap and diagonal. Use as retro fit kit for earlier models. Earlier models may requireadditional brackets.
Defender
Inertia Centre Belt
BA 187A Defender
D e f e n d e r
54
Passionate about Land Rovers www.bearmach.com
3 Point Inertia Seat Belt
BA 188 Std Defender
3 Point Inertia Seat Belt
BA 188A Short Reel Defender
3 Point Inertia Seat Belt
BA 188B Angled Reel Defender
Seat Heater
BA 2410
Seat heater available built-in to new seats or DIY kit to fit inside your seats. With full fittinginstructions wiring loom and switches.
Pair Defender
Seat Riser
BA 2417
Creates more space between wheel and seat back. - Increase leg room - Fits driver andpassenger side - Includes fitting instructions, bolts and allen key.
Defender
D e f e n d e r
55
www.bearmach.com Passionate about Land Rovers
Moulded Mat System
BA 2482
These durable mat systems improve sound deadening and heat transfer from the gearbox andexhaust system. They provide excellent protection from all dirt and are easily cleanable. Themat system is made from polyethylene, to give a very hard wearing product.
LT77 Gearbox Defender
BA 2480 R380/LT85/Auto Gearbox Defender (upto 2006)
Load Area Matting
BA 2484
Heavy duty, ribbed, rubber matting to suit rear load areas.
Defender 110 (Hard Top)
BA 2483 Defender 90/110 (SW County)
Heavy Duty Rubber Mats
BA 3510
Strong and waterproof, the weight of these mats ensures that they do not move when in thevehicle and keep the carpet clean.
2nd Row Defender 110
BA 3501 Universal - Pair Defender
Rubber Mat
BTR7898 RH - Front - R380 Defender
BTR7897 LH - Front -R380 Defender
BTR7896 RH - Front - LT77 Defender
BTR7895 LH - Front - LT77 Defender
Steering Wheel
BA 151
Three spoke design chrome and black spokes availableNot for off Road use
15" Leather Steering Wheel Defender
BA 150 14" Vinyl Steering Wheel Defender
D e f e n d e r
56
Passionate about Land Rovers www.bearmach.com
Steering Wheel Boss (to fit BA 150/151)
BA 154 Defender 90/110 (upto 1991 + all County Station Wagons)
Black Moulded Steering Wheel
BA 3209
A plastic moulded steering wheel - especially designed for comfort with an ergonomic griparea.
Horn Push Defender
BA 3202 340mm Defender
Wood Rim Steering Wheel
BA 3209
A classic wood wheel with high gloss finish and 3 chrome spokes.
Horn Push Defender
BA 3203 350mm Defender
Black Leather Steering Wheel
BA 3201
These are quality genuine leather sports steering wheels ideal for the rigours of off-roading.
Boss - 48 Spline Defender
BA 3200 Boss - 36 Spline Defender
BA 3207 350mm Defender
Black Alcantara Wheel
BA 3201
These are quality genuine leather sports steering wheels ideal for the rigours of off-roading.
Boss - 48 Spline Defender
BA 3200 Boss - 36 Spline Defender
BA 3208 350mm Defender
D e f e n d e r
57
www.bearmach.com Passionate about Land Rovers
Wading Kit
BA 2168A
Consists of breather pipes for axles, gearbox and timing cover.
Defender TD5
BA 2167 Defender 200/300TDi
Raised Air Intake - BM
BA 2124A
Fitting a raised air intake and wading kit to your vehicle means cleaner air in dusty conditionsand improved wading ability in wet or flooded conditions.
Metal Defender (200TDi/TD)
BA 2124 Plastic Defender (200TDi/TD)
BA2123AM Metal Defender (300/TD5)
BA 2123 Plastic Defender (300/TD5)
Gearbox Bearing Kits
BK 0007A
Contains all the bearings required for a rebuild
13 Piece Kit Defender
BK 0007 13 Piece Kit Defender
BK 0006B 9 Piece Kit Defender LT77 Suff H
BK 0006A 8 Piece Kit Defender LT77 Suff F-G
BK 0006 7 Piece Kit Defender
Wheel Bearing Kits
BK 0102 Front / Rear Defender 90/110 (LA on)
BK 0101 Front Defender 90/110 (KA on)
BK 0100 Rear Defender 90/110 (upto KA)
Head Bolt Kits
BK 0113 12 Bolt Kit TD5 - Defender
BK 0112 18 Bolt Kit 300Tdi - Defender
BK 0111 18 Bolt Kit 200Tdi - Defender
D e f e n d e r
58
Passionate about Land Rovers www.bearmach.com
Timing Kit
STC4096K
Contains all the parts needed to change the timing belt
300Tdi - Defender
Timing Kit
BK 0120
Contains all the parts needed to change the timing belt
200Tdi - Defender
Timing Kit
BK 0122
Contains all the parts needed to change the timing belt
2.5D/TD - Defender
Blue Springs
D e f e n d e r
59
Contents
Gasket
Timing Belt
Idler
Tensioner
Pulley
Contents
Timing Belt
Gasket
Tensioner
Idler
Contents
Gasket
Timing Belt
Tensioner
Gasket
PART NUMBER FITMENT APPLICATION HEIGHT INCREASE RATE WIRE HEIGHT
BA 2100 Rear 110/130 40mm 510lbs 22mm 410mm
BA 2100B Rear 110 40mm 420lbs 21mm 420mm
BA 2101 Front 90/110 45mm 255lbs 17mm 380mm
BA 2102 Rear 90 40mm 295lbs 18mm 445mm
BA 2103 Rear 90 20mm 240lbs 17mm 413mm
BA 2104 Front 90 30mm 195lbs 16mm 394mm
BA 2105 Rear 90 30mm 194lbs 16mm 438mm
BA 2106 Front 90 30mm 196lbs 16mm 368mm
BA 2107 Rear 90 30mm 195.5lbs 16mm 413mm
BA 2251 Front* Defender 50mm 175lbs
BA 2252 Rear* 90 50mm 225lbs
BA 2253 Rear* 110 50mm 330lbs
* +2" Springs to fit standard vehicle but intended for off road use only.
www.bearmach.com Passionate about Land Rovers
Shock Absorbers for Defender
Steering Dampers for Defender
Extreme Lift Kit
BA 3683 Defender 110 (with wide bushes)
BA 3682 Defender 110 (with narrow bushes)
Plus 2” Lift Kit
BA 3752 Defender 110
BA 3750 Defender 90
D e f e n d e r
60
BRAND FILL + TUBE TYPE EXTENSION(MM)
DEFENDER UPTO 1998 DEFENDER FROM 1998
FRONT REAR FRONT REAR
Boge/Sachs Oil BR 0645 BR 1077 BR 0645 STC2850
Armstrong Oil BR 0645A BR 1077A BR 0645A STC2850A
Monroe Gas BR 0645M BR 1077M BR 0645M STC2850M
Decarbon Gas BA 2241 BA 2242 BA 2241 BA 2246
Decarbon Gas 50 BA 2249 BA 2250 BA 2249 BA 2250
Bilstein Gas BA 2122 BA 2119 BA 2122 BA 2119
Procomp Gas 0-25 BR 0645P BR 1077P BR 0645P BR 1077P
Procomp Gas 50 BR 0645L BR 1077L BR 0645L BR 1077L
Procomp Gas 100 BR 0645XL BR 1077XL BR 0645XL BR 1077XL
OME Gas 0-25 BA 2120 BA 2121 BA 2120 BA 2121
OME Gas Heavy Duty 0-25 BA 2120H BA 2121H BA 2120H BA 2121H
Koni Gas 0-25 BR 0645K BR 1077K BR 0645K -
Koni Gas 50 BR 0645KL BR 1077KL BR 0645KL BR 1077KL
Koni Raid Gas Heavy Duty 45 BR 0645KH BR 1077KH BR 0645KH BR 1077KH
Tuffback Gas Heavy Duty 0-50 BA 2502 BA 2503 BA 2510 BA 2511
Tuffback Gas Heavy Duty 50-100 BA 2514 BA 2515 BA 2524 BA 2525
MAKE
Boge/Sachs BR 3604
Armstrong BR 3604A
Decarbon BA 2248
BUSH KITS (FOR PIN END ONLY)
Monroe BR 0645MK
Procomp P1029
3° Cranked Radius Arms and Rear Links
2 Pairs of +40mm Springs
2 Pairs of +50mm Procomp Shock Absorbers
Spring Retainers
2 Pairs +2" Springs
2 Pairs +2" Procomp 9000 Series Shock Absorbers
www.bearmach.com Passionate about Land Rovers61
D e f e n d e r
DEFENDER 90CV JOINT
FRONT
SHAFT
REAR
SHAFT
DRIVE FLANGE
(FRONT)DRIVE FLANGE
(REAR)VEHICLE SPECIFICATION
Turbo Diesel - circa 1989 (see note 1) BA 5764 BA 5752 BA 5750 FRC5806A FRC5806A
200 Tdi - To KA930455 (see note 1) BA 5764 BA 5752 BA 5750 FRC5806A FRC5806A
200 Tdi - from LA930456 (see note 1) BA 5764 BA 5752 BA 5758 FTC859A FTC859A
300 Tdi/TD5/2.4 Tdci (see note 5) BA 5760 BA 5752 BA 5758 FTC859A FTC859A
DEFENDER 110CV JOINT
FRONT
SHAFTREAR SHAFT
DRIVE FLANGE
(FRONT)
DRIVE FLANGE
(REAR)VEHICLE SPECIFICATION
Turbo Diesel - circa 1989 (see note 1) BA 5764 BA 5752 Unable to Supply FRC5806A FRC5806A
200 Tdi (see note 1) BA 5764 BA 5752 Unable to Supply FRC5806A FRC5806A
300 Tdi (see notes 2&5) BA 5760/BA 5761 BA 5752 BA 5751 FTC859A FTC859A
Puma (see notes 2 & 5) BA 5760/BA 5761 BA 5752 BA 5758 FTC859A FTC859A
NOTE 1 If replacing standard stock 10 spline you will also require some form of 24 spline diff centre.
NOTE 2Our CV joints can only be fitted with our or other 23 spline shafts. If your rear shafts have integralflanges it will be necessary for you to fit other flanges.
NOTE 5 The CV joint ABS style can only be fitted with our range of shafts.
Service Kits
Contains all parts to complete a quick and simple service(Image for illustration purposes only)
7:1 Compression Ratio
BK 0010 2½ Petrol
Service Kits
BK 0011
Contains all parts to complete a quick and simple service(Image for illustration purposes only)
ContentsOil FilterAir FilterFuel FilterSpark PlugsSump Plug Washer
2.5 Turbo Diesel
ContentsOil FilterAir FilterFuel FilterSump Plug Washer
www.bearmach.com Passionate about Land Rovers
Service Kits
BK 0012
Contains all parts to complete a quick and simple service(Image for illustration purposes only)
200 Tdi
Service Kits
BK 0013
Contains all parts to complete a quick and simple service(Image for illustration purposes only)
300 Tdi
Service Kits
BK 0014
Contains all parts to complete a quick and simple service(Image for illustration purposes only)
TD5
Service Kits
BK 0069
Contains all parts to complete a quick and simple service(Image for illustration purposes only)
07> Puma
D e f e n d e r
62
ContentsOil FilterAir FilterFuel FilterSump Plug Washer
ContentsOil FilterAir FilterFuel FilterSump Plug Washer
ContentsOil FilterAir FilterRotor FilterFuel FilterSump Plug Washer
ContentsAir FilterOil FilterFuel FilterOil Drain Plug
www.bearmach.com Passionate about Land Rovers63
D e f e n d e r
RE-TRIM KITS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2401XS Re-trim Kit Driver/Passenger LeatherBA 2401XSL Re-trim Kit Passenger LeatherBA 2401XSR Re-trim Kit Driver LeatherBA 2446XS Re-trim Kit Rear Fold-up LeatherBA 2447 Re-trim Kit Centre Seat LeatherBA 2401G Re-trim Kit Driver/Passenger Grey VinylBA 2401GL Re-trim Kit Passenger Grey VinylBA 2401GR Re-trim Kit Driver Grey VinylBA 2401DT Re-trim Kit Driver/Passenger Denim TwillBA 2401DTL Re-trim Kit Passenger Denim TwillBA 2401DTR Re-trim Kit Driver Denim TwillBA 2401M Re-trim Kit Driver/Passenger Grey Logo - ClothBA 2401OB Re-trim Kit Driver/Passenger Outlast LakelandBA 2401T Re-trim Kit Driver/Passenger TechnoBA 2401TL Re-trim Kit Passenger TechnoBA 2401TR Re-trim Kit Driver TechnoBA 2446T Re-trim Kit Rear Fold-up Techno
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2077 Complete Seat High Back Front (upto 1985) Black VinylBA 2078 Complete Seat High Back Front (upto 1985) CaviarBA 2079 Complete Seat High Back Front (upto 1985) BrushwoodBA 2440G Complete Seat Driver/Passenger Grey VinylBA 2440GL Complete Seat Left Hand Grey VinylBA 2440GR Complete Seat Right Hand Grey VinylBA 2440DT Complete Seat Driver/Passenger Denim TwillBA 2440T Complete Seat Driver/Passenger TechnoBA 2440TL Complete Seat Left Hand TechnoBA 2440TR Complete Seat Right Hand TechnoBA 2440XS Complete Seat Driver/Passenger Leather
SEAT BASE
PART NUMBER DESCRIPTION FITMENT TRIM
BR 2016 Seat Base Driver/Passenger BlackBR 2016G Seat Base Driver/Passenger Grey VinylBR 2016D Seat Base Driver/Passenger Denim TwillBR 2016T Seat Base Driver/Passenger TechnoBR 2016F Seat Base Foam ONLY
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2445XS Complete Seat Centre LeatherBA 2445G Complete Seat Centre Grey VinylBA 2445DT Complete Seat Centre Denim TwillBA 2445T Complete Seat Centre Techno
CONVERSION KIT
BA 2406 Conversion Kit (Sub Frame) Adapts to accept BA 2404/5XS (3 Seats)
www.bearmach.com Passionate about Land Rovers64
D e f e n d e r
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2092XS Complete Seat Rear Fold-up LeatherBA 2093 Complete Seat Rear Fold-up (Side facing) Black VinylBA 2093G Complete Seat Rear Fold-up (Side facing) Grey VinylBA 2093L Complete Seat Rear Fold-up (Side facing) Black LogoBA 2093T Complete Seat Rear Fold-up (Side facing) TechnoBA 2092T Complete Seat Rear Fold-up (Side facing) TechnoBA 2080 Complete Seat Rear LH/RH (Forward facing) Black VinylBA 2080RH Complete Seat Rear RH (Forward facing) Black VinylBA 2080T Complete Seat Rear LH/RH (Forward facing) TechnoBA 2081 Complete Seat Rear LH/RH (Forward facing) MoorlandBA 2082 Complete Seat Rear BrushwoodBA 2082B Complete Seat Rear LH (Forward facing) Grey VinylBA 2082AB Complete Seat Rear LH/RH (Forward facing) Grey VinylBA 2080D Complete Seat Rear LH/RH (Forward facing) Denim TwillBA 2080DR Complete Seat Rear RH (Forward facing) Denim Twill
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BR 1696 Complete Seat Hinged Rear Bench (Side facing) Black VinylBR 1696G Complete Seat Hinged Rear Bench (Side facing) Grey VinylBR 1696M Complete Seat Hinged Rear Bench (Side facing) MoorlandBR 1696T Complete Seat Hinged Rear Bench (Side facing) TechnoBR 1696DT Complete Seat Hinged Rear Bench (Side facing) Denim Twill
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2405XS Complete Seat High Back 110 Second Row LeatherBA 2405T Complete Seat High Back 110 Second Row TechnoBA 2405G Complete Seat High Back 110 Second Row Grey VinylBA 2405B Complete Seat High Back 110 Second Row Black Vinyl
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2404T Complete Seat Low Back 110 Second Row TechnoBA 2404B Complete Seat Low Back 110 Second Row Black VinylBA 2404G Complete Seat Low Back 110 Second Row Grey VinylBA 2404L Complete Seat Low Back 110 Second Row Black Logo
COMPLETE SEATS
PART NUMBER DESCRIPTION FITMENT TRIM
BA 2402G Complete Seat Inward Facing Grey VinylBA 2402L Complete Seat Inward Facing Black / Grey LogoBA 2402M Complete Seat Inward Facing Grey LogoBA 2402T Complete Seat Inward Facing TechnoBA 2403B Complete Seat Inward Facing (Tip-up) Black VinylBA 2403T Complete Seat Inward Facing (Tip-up) Techno