Description- Temperature monitoring inside the UXC racks.- Each rack can have up to 16 analogue inputs.- Signals will be read through the DCS system:
they can be shown on the rack monitoring panels, you can receive mail or SMS notification or send alarms to the alarm screen on values exceeding predefined limits.
+ 1 PP/rack (70CHF each) Cable to the turbine unit included in the price.Prices might be lower when ordered more than 20 units.
+ Sensors with halogen free cables:NTC 10k Ohm, -35°C...+100°C6 x 32mm, 2 x 0.25qmmPE-Cable: 20 pieces: 35CHF/piece100 pieces: 25CHF/piece500 pieces: 20CHF/piece
+ some resistor arrays for the ELMB. (low price).The cable is the most expensive here.
YB0----1- X4A01 LV2- X4A02 HV3- X4J01 LV4- X4J02 HV
5- X2A01 LV6- X2J01 LV7- X2J02 SC
8- X2N35 HV9- X2F34 HV
YB-1------28- X4S11 LV29- X4S12 HV30- X4V11 LV31- X4V12 HV
32- X3S12 HV33- X3V12 HV
34- X2S11 LV35- X2V11 LV36- X2V12 SC
YB-2------37- X4S21 LV38- X4S22 HV39- X4V21 LV40- X4V22 HV
41- X3S22 HV42- X3V22 HV
43- X2S21 LV44- X2V21 LV45- X2V22 SC
YB+1------10- X4A11 LV11- X4A12 HV12- X4J11 LV13- X4J12 HV
14- X3A12 HV15- X3J12 HV
16- X2A11 LV17- X2J11 LV18- X2J12 SC
YB+2------19- X4A21 LV20- X4A22 HV21- X4J21 LV22- X4J22 HV
23- X3A22 HV24- X3J22 HV
25- X2A21 LV26- X2J21 LV27- X2J22 SC
LIST OF DT RACKS
DT system. What we want:
4 NTC sensors/rack.
HV and SC racksWater in/out (not in the following pictures, already installed in all racks) + 2 inside the air volume of the rack.
LV racksWater in/out (not in the following pictures, already installed in all racks) Water in/out in middle heat exchanger (indicated in the picture)
Length of the cable sensor from the patch pannel ~2.0 m
45 racks => 45 PP (+1 spare) = 46 PP 180 NTC sensors (+20 spares) = 200 PP
RPC does not need extra sensors as long as we put ours on top of their MAOs in HV racks.
We have to see how this PP is fixed in the racks.
We said we didn´t needed on USC.
Connection to patch pannel:
Each sensor:cable 1 of probe to connectors 1, 3, 5, … of patch pannelcable 2 of probe to connectors 2, 4, 6, … of patch pannel.
Pair 1, 2 => sensor of pipe “water in” of the rack.Pair 3, 4 => sensor of pipe “water out” of the rack.Pair 5, 6 => LV racks: sensor of “water in” in middle heat exchanger
SC racks: sensor on top of SC crate top closest to S1 HV racks: sensor below upper RPC crate
Pair 7, 8 => LV racks: sensor of “water out” in middle heat exchanger SC racks: sensor on top of SC crate top closest to S6 HV racks: sensor below HV rack
All patch pannels are in place. Turbine modification and cable from PP to turbine missing in all racks except SC racks.
Ok, installedForeseen, to be installed in the futureVittorio was installing them. I could not check if he finished.
Legend of circles in next plots
Turbine modified, patch pannel connected to turbine.
LV rack
LV rack
LV rack
LV rack
HV rackHV rack
HV rack HV rack
SC rack
LV rack
LV rack
LV rack
LV rack
HV rackHV rack
HV rack HV rack
SC rack
LV rack
LV rack
LV rack
LV rack HV rackHV rack
HV rack HV rack
SC rack
YB-1´s racks
LV rack
LV rack
LV rack
LV rack
HV rackHV rack
HV rack HV rack
SC rack
YB-2´s racks
LV rack
LV rack
LV rack
LV rack
HV rack
HV rack
HV rack HV rack
SC rack
Example: sensor attached to water pipe.
HV racks: sensor inside the air volume. Attached to RPC crate top.
HV racks: sensor inside the air volume. Attached to RPC crate top.
HV racks: sensor inside the air volume. Probe in the lower part of the HV crate.
HV racks: sensor inside the air volume. Probe in the lower part of the HV crate.
SC racks: YB-2, 0, +2 (Alignment crate)
SC racks: YB-1, +1 (No alignment crate)
YB0----1- X4A01 LV2- X4A02 HV3- X4J01 LV4- X4J02 HV
5- X2A01 LV6- X2J01 LV7- X2J02 SC
8- X2N35 HV9- X2F34 HV
YB-1------28- X4S11 LV29- X4S12 HV30- X4V11 LV31- X4V12 HV
32- X3S12 HV33- X3V12 HV
34- X2S11 LV35- X2V11 LV36- X2V12 SC
YB-2------37- X4S21 LV38- X4S22 HV39- X4V21 LV40- X4V22 HV
41- X3S22 HV42- X3V22 HV
43- X2S21 LV44- X2V21 LV45- X2V22 SC
YB+1------10- X4A11 LV11- X4A12 HV12- X4J11 LV13- X4J12 HV
14- X3A12 HV15- X3J12 HV
16- X2A11 LV17- X2J11 LV18- X2J12 SC
YB+2------19- X4A21 LV20- X4A22 HV21- X4J21 LV22- X4J22 HV
23- X3A22 HV24- X3J22 HV
25- X2A21 LV26- X2J21 LV27- X2J22 SC
LIST OF DT RACKS
W+111 X2A11 FE LV 12 X2A12 LBBOX + HO LV13 X2J11 FE LV14 X2J12 LBBOX
15 X3A12 LBOX LV + LBBOX+MAO16 X3J12 LBOX LV + LBBOX+MAO
17 X4A11 FE LV 18 X4A12 LBBOX19 X4J11 FE LV
20 X4J12 LBBOX
LIST OF RPC BARREL RACKS IN UXC: red are only RPC-H0, racks-no DT
W-131 X2S11 FE 32 X2S12 LBBOX + HO33 X2V11 FE LV 34 X2V12 LBBOX
35 X3V12 LBOX LV + LBBOX+MAO 36 X3S12 LBOX LV + LBBOX+MAO
37 X4S11 FE RPC38 X4S12 LBBOX39 X4V11 FE LV 40 X4V12 LBBOX
W-241 X2S21 FE LV 42 X2S22 LBBOX + HO LV43 X2V21 FE LV 44 X2V22 LBBOX
45 X3S22 LBOX LV + LBBOX+MAO46 X3V22 LBOX LV + LBBOX+MAO47 X2S21 FE LV 48 X2S22 LBBOX49 X2V21 FE LV 50 X2V22 LBBOX
W+221 X2A21 FE LV 22 X2A22 LBBOX + HO LV23 X2J21 FE LV24 X2J22 LBBOX
29 X3a22 LBOX LV + LBBOX+MAO30 X3J22 LBOX LV + LBBOX+MAO
25 X4A21 FE LV 26 X4A22 LBBOX 27 X4J21 FE LV28 X4J22 LBBOX
W01 X2A01 FE LV 2 X2A02 LBBOX + ALIGN3 X2J01 FE RPC4 X2J02 LBOX
5 X2N35 LBBOX LV + MAO6 X2F34 LBBOX LV + MAO
7 X4A01 FE LV RPC8 X4A02 LBBOX LV9 X4J01 FE RPC10 X4J02 LBOX
X21 X2A32 RE2 X2A52 RE3 X2J32 RE4 X2J52 RE5 X2S32 RE6 X2S52 RE7 X2V32 RE8 X2V52 RE
X39 X3A51 RE10 X3J51 RE11 X3S51 RE12 X3V51 RE
X413 X4A32 RE14 X4A52 RE15 X4J32 RE16 X4J51 RE17 X4S32 RE18 X4S51 RE19 X4V32 RE20 X4V51 RE
LIST OF RPC ENDCAP RACKS IN UXC: red are only RPC racks - no CSC
LIST OF RPC BARREL RACKS IN S1 with HV
1 S1H03 2 S1H043 S1H054 S1H065 S1H07
LIST OF RPC ENDCAP RACKS IN S1 with HV
1 S1H08 2 S1H093 S1H104 S1H11
BCOPW1
W+2
BC0PW1
BC0PW1
S1H06
dist
dist
dist
Position of t-sensors in USC racks
HV racks in USC