Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 1 of 44
Description:0301-CR-ST-FQ-T2-S2-No.3 Mtl Group:Stainless Steel Material: 0301 Mtl Spec Code:22 Final Processing: Cold rolled. Mtl Form: Strip Quality: Forming Quality Temper: Half Hard Surface : Bright Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 666 Addnl. Spec: SAE J405 Exception: Grain Size: Note: Thickness +/- .001 Width +/- .005. Hardness: This material is specified by yield strength (110,000 lbs/ins).
Fitness Note: Fitness For Use: This material must be fit for forming. The end product will be utilized in an occupant restraint system as a spring. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . . 1.000
Manganese . : 2.000 Nickel . . . 6.000 8.000
Phosphorus . 0.045 Chromium . . 16.000 18.000
Sulphur . . . 0.030 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 2 of 44
Description:050 XF-1P-ST-SQ-TT-AR-No.3 Mtl Group:High Strength Steel Material: 050 XF Mtl Spec Code: 18 Final Processing: Hot rolled followed by one pass cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Not Specified Surface : As Rolled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A1008/A 1008M 04b HSLAS-F Addnl. Spec: Exception: Substitution of 050 XF Material- Per SAE J1392 is acceptable. Grain Size: Note: Hardness: This material is specified by yield strength.
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . .
Manganese . : 1.650 Nickel . . . 0.200
Phosphorus . 0.020 Chromium . . 0.150
Sulphur . . . 0.025 Molybdenum : 0.060
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 3 of 44
Description: 050 XF-HR-ST-SQ-TT-PO-No.3 Mtl Group: High Strength Steel Material: 050 XF Mtl Spec Code:1
Final Processing: Hot rolled. Mtl Form: Strip Quality: Special Quality Temper: Not Specified Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM 1008/A 1008M 04b Addnl. Spec: Exception: Substitution of 050 XLF Material- Per SAE J1392 is acceptable. Grain Size: Note: Hardness: This material is specified by yield strength.
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . .
Manganese . : 1.650 Nickel . . . 0.200
Phosphorus . 0.020 Chromium . . 0.150
Sulphur . . . 0.025 Molybdenum : 0.060
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 4 of 44
Description: 060 XF-1P-ST-SQ-TT-AR-No.3 Mtl Group: High Strength Steel Material: 060 XF Mtl Spec Code: 2 Final Processing: Hot rolled followed by one pass cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Not Specified Surface : As Rolled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 1008/A 1008M 04b HSLA-F Addnl. Spec: Exception: Substitution of 060 XLF Material- Per SAE J1392 is acceptable. Grain Size: Note: Hardness: This material is specified by yield strength.
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . .
Manganese . : 1.650 Nickel . . . 0.200
Phosphorus . 0.020 Chromium . . 0.150
Sulphur . . . 0.025 Molybdenum : 0.060
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 5 of 44
Description:060 XF-HC-ST-SQ-TT-PO-No.3 Mtl Group:High Strength Steel Material:060 XF Mtl Spec Code:34
Final Processing: Hot or Cold Rolled Mtl Form: Strip Quality: Special Quality Temper: Not Specified Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A1011/A 1011M HSLA-F Addnl. Spec: ASTM A1008/A 1008M Exception: Substitution of 080 XLF Material- Per SAE J1392 is acceptable. Grain Size: Note: Hardness: This material is specified by yield strength.
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . .
Manganese . : 1.650 Nickel . . . 0.200
Phosphorus . 0.020 Chromium . . 0.150
Sulphur . . . 0.025 Molybdenum : 0.060
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 6 of 44
Description:060 XF-HR-ST-SQ-TT-PO-No.3 Mtl Group:High Strength Steel Material: 060 XF Mtl Spec Code:3 Final Processing: Hot rolled. Mtl Form: Strip Quality: Special Quality Temper: Not Specified Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A1011/A 1011M 04a HSLA-F Addnl. Spec: Exception: Substitution of 080 XLF Material- Per SAE J1392 is acceptable. Grain Size: Note: Hardness: This material is specified by yield strength.
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . .
Manganese . : 1.650 Nickel . . . 0.200
Phosphorus . 0.020 Chromium . . 0.150
Sulphur . . . 0.025 Molybdenum : 0.060
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 7 of 44
Description:080 XF-HR-ST-SQ-TT-PO-No.3 Mtl Group:High Strength Steel Material: 080 XF
Mtl Spec Code: 35
Final Processing: Hot rolled. Mtl Form: Strip Quality: Special Quality Temper: Not Specified Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A1011/A 1011M 04a HSLAS-F Addnl. Spec: Exception: Substitution of 080 XLF Material- Per SAE J1392 is acceptable. Grain Size: Note: Hardness: This material is specified by yield strength.
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.150 Silicon . . .
Manganese . : 1.650 Nickel . . . 0.200
Phosphorus . 0.020 Chromium . . 0.150
Sulphur . . . 0.025 Molybdenum : 0.160
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 8 of 44
Description:1008-CR-SH-CQ-AR-AR-N/A Mtl Group:Low Carbon Steel Material: 1008 Mtl Spec Code:33
Final Processing: Cold rolled. Mtl Form: Sheet Quality: Commercial Quality Temper: As Rolled Surface : As Rolled Edge Condition: Not Applicable Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 60 - 75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.100 Silicon . . .
Manganese . : 0.250 0.500 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 9 of 44
Description: 1008-CR-ST-CQ-T2-PO-No.3 Mtl Group:Low Carbon Steel Material:1008 Mtl Spec Code:44 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Half Hard Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 60 - 75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.100 Silicon . . .
Manganese . : 0.250 0.500 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 10 of 44
Description:1008-CR-ST-CQ-T4-S1-No.3 Mtl Group:Low Carbon Steel Material:1008 Mtl Spec Code: 37
Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Skin Rolled Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: B65 Max
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.100 Silicon . . .
Manganese . : 0.500 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 11 of 44
Description:1008-HR-ST-CQ-T3-S1-No.3 Mtl Group:Low Carbon Steel Material:1008 Mtl Spec Code:42 Description: 1008-HR-ST-CQ-T3-S1-No.3 Mtl Group: Low Carbon Steel Material: 1008
Final Processing: Hot rolled. Mtl Form: Strip Quality: Commercial Quality Temper: As Rolled Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 569/A 569M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: Note: Hardness: Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.100 Silicon . . .
Manganese . : 0.500 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 12 of 44
Description:1010-1P-ST-CQ-T3-S1-No.3 Mtl Group:Low Carbon Steel Material: 1010 Mtl Spec Code: 21
Final Processing: Hot rolled followed by one pass cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Quarter Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A109 Addnl. Spec: Compostion per ASTM A568/A568M. Exception: No Exception. Grain Size: Note: Hardness: 60-75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processes The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 13 of 44
Description:1010-CR-SH-CQ-AR-AR-N/A Mtl Group:Low Carbon Steel Material:1010 Mtl Spec Code:32 Final Processing: Cold rolled. Mtl Form: Sheet Quality: Commercial Quality Temper: As Rolled Surface : As Rolled Edge Condition: Not Applicable Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 60 - 75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 14 of 44
Description:1010-CR-ST-CQ-T2-PO-No.3 Mtl Group:Low Carbon Steel Material:1010 Mtl Spec Code:45 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Half Hard Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 569/A 569M Addnl. Spec: Composition per ASTM A682 Exception: No Exceptions Grain Size: Note: Hardness: 60 - 75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 15 of 44
Description:1010-CR-ST-CQ-T3-S1-No.3 Mtl Group:Low Carbon Steel Material:1010 Mtl Spec Code:4 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Quarter Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 60 - 75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 16 of 44
Description:1010-CR-ST-CQ-T4-S1-No.3 Mtl Group:Low Carbon Steel Material:1010 Mtl Spec Code:5 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Skin Rolled Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: HRB 65 Max
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 17 of 44
Description:1010-CR-ST-CQ-T4-S2-No.3 Mtl Group:Low Carbon Steel Material:1010 Mtl Spec Code:19
Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Skin Rolled Surface : Bright Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: Fitness Fitness Note: Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 18 of 44
Description:1010-HR-ST-CQ-T3-S1-No.3 Mtl Group:Low Carbon Steel Material:1010 Mtl Spec Code:6 Final Processing: Hot rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Quarter Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 569/A 569M Addnl. Spec: Composition per ASTM A682 Exception: No Exceptions Grain Size: Note: Hardness: 60 - 75 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.080 0.130 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 19 of 44
Description:1018-HR-SH-CQ-T3-S1-No.3 Mtl Group:Low Carbon Steel Material:1018 Mtl Spec Code: 38 Final Processing: Hot rolled. Mtl Form: Sheet Quality: Commercial Quality Temper: Quarter Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Coposition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 70 - 85 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.140 0.200 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 20 of 44
Description:1020-CR-ST-CQ-T2-PO-No.3 Mtl Group:Low Carbon Steel Material:1020 Mtl Spec Code:46 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Half Hard Surface : Pickled & Oiled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 70 - 85 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.170 0.230 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 21 of 44
Description:1020-CR-ST-CQ-T2-S1-No.3 Mtl Group:Low Carbon Steel Material:1020 Mtl Spec Code:7 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Half Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per X1.1 ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 70 - 85 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.170 0.230 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 22 of 44
Description:1020-HR-SH-CQ-T3-S1-No.3 Mtl Group:Low Carbon Steel Material:1020 Mtl Spec Code:39
Final Processing: Hot rolled. Mtl Form: Sheet Quality: Commercial Quality Temper: Quarter Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 109 Addnl. Spec: Composition per ASTM A568/A568M Exception: No Exceptions Grain Size: Note: Hardness: 70 - 85 HRB
Fitness
Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.170 0.230 Silicon . . .
Manganese . : 0.300 0.600 Nickel . . .
Phosphorus . 0.030 Chromium . .
Sulphur . . . 0.035 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 23 of 44
Description:1040-CR-ST-CQ-SA-S1-No.3 Mtl Group:Medium Carbon Steel Material:1040 Mtl Spec Code:8 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Std Min Max Std Min Max
Carbon . . . 0.370 0.440 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 24 of 44
Description:1040-HR-ST-CQ-IN-S1-No.3 Mtl Group:Medium Carbon Steel Material:1040 Mtl Spec Code:9 Final Processing: Hot rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Intermediate Hardness Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 569/A 569M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: HRB 90 Max. Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.370 0.440 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure:
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 25 of 44
Description:1050-1P-ST-SQ-SA-S1-No.1 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:27 Final Processing: Hot rolled followed by one pass cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Round edge. Gen Spec: ASTM A 749/749M Addnl. Spec: Exception: Substitution of cold rolled material per IMMI Spec 1050 CR ST-SQ-SA-S1 is acceptable. Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 26 of 44
Description:1050-1P-ST-SQ-SA-S1-No.3 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:10 Final Processing: Hot rolled followed by one pass cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 749/749M Addnl. Spec: Exception: Substitution of cold rolled material per IMMI Spec 1050 CR ST-SQ-SA-S1 is acceptable. Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 27 of 44
Description:1050-1P-ST-SQ-SA-S1-No.4 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:29 Final Processing: Hot rolled followed by one pass cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Round edge produced by edge rolling. Gen Spec: ASTM A 749/749M Addnl. Spec: Exception: Substitution of cold rolled material per IMMI Spec 1050 CR ST-SQ-SA-S1 is acceptable. Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 28 of 44
Description:1050-CR-ST-SQ-SA-AR-No.3 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:20 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : As Rolled Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 29 of 44
Description:1050-CR-ST-SQ-SA-S1-No.3 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code: 11 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 30 of 44
Description:1050-CR-ST-SQ-SA-S2-No.3 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:12 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Bright Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 31 of 44
Description:1050-CRG-ST-SQ-SA-S1-No.3 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:30 Final Processing: CRS Followed by Additional Pass or Passes for Gage Control Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: Substitution of aluminum killed material is acceptable. Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 32 of 44
Description:1050-HR-SH-SQ-SA-PO-No.3 Mtl Group:High Carbon Steel Material:1050 Mtl Spec Code:40 Final Processing: Hot rolled. Mtl Form: Sheet Quality: Special Quality Temper: Spheroidize Annealed Surface : Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: No Exceptions. Grain Size: Al Killed 6-9 Grain S Note: Grain size of the material should be predominately equiaxed with t ize he range specified above. Grain size shall be determined in accord ance with ASTM E112. Hardness: Per ASTM A684/A684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or disintegrat
ing plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 33 of 44
Description:1050-HR-ST-SQ-SA-S1-No.3 Mtl Group:High Carbon Steel Material:1050
Mtl Spec Code:36 Final Processing: Hot rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: Grain Size: 6-9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: Per ASTM A684/684M, Figure 2. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.480 0.550 Silicon . . .
Manganese . : 0.600 0.900 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.050 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 34 of 44
Description:1050M-CR-ST-SQ-SA-S2-No.3 Mtl Group:High Carbon Steel Material:1050M Mtl Spec Code:17 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Bright Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Exception: Inclusion content (sulphides, alumina, silicates, and oxides) to be no greater than rating #2 (lig
ht) per ASTM E45. Grain Size: 5 Grain Size Max. Note: NOTE: Grain size of the material should be predominately equiaxed
with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: HRB 76 Max. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, and plating processe s. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.470 0.550 Silicon . . . 0.020
Manganese . : 0.450 0.750 Nickel . . .
Phosphorus . 0.020 Chromium . .
Sulphur . . . 0.020 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 35 of 44
Description:1095-CR-ST-SQ-SA-S1-No.3 Mtl Group:High Carbon Steel Material:1095 Mtl Spec Code:13 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Spheroidize Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 684/684M Addnl. Spec: Composition per ASTM A682 Exception: No Exceptions Grain Size: Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: HRB 90 Max. Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.900 1.040 Silicon . . . 0.150 0.300
Manganese . : 0.300 0.500 Nickel . . .
Phosphorus . 0.035 Chromium . .
Sulphur . . . 0.040 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 36 of 44
Description:1141-CR-BR-SQ-A-AR-N/A Mtl Group:Medium Carbon Steel Material:1141 Mtl Spec Code:14 Final Processing: Cold rolled. Mtl Form: Bar Quality: Special Quality Temper: Annealed Surface : As Rolled Edge Condition: Not Applicable Gen Spec: ASTM A 29 /A 29M Addnl. Spec: Exception: No Exceptions
Grain Size: Si Killed, 6-9 Grain Note: NOTE: Grain size of the material should be predominately equiaxed Size with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: 85 HRB MAX
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.370 0.450 Silicon . . . 0.200
Manganese . : 1.350 1.650 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.080 0.130 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 37 of 44
Description:1144-CR-BR-SQ-A-AR-N/A Mtl Group:Medium Carbon Steel Material:1144 Mtl Spec Code: 31 Final Processing: Cold rolled. Mtl Form: Bar Quality: Special Quality Temper: Annealed Surface : As Rolled Edge Condition: Not Applicable Gen Spec: ASTM A 29 /A 29M Addnl. Spec: Exception: No Exceptions
Grain Size: Si Killed, 6-9 Grain Note: NOTE: Grain size of the material should be predominately equiaxed Size with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: 85 HRB MAX
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.400 0.480 Silicon . . .
Manganese . : 1.350 1.650 Nickel . . .
Phosphorus . 0.040 Chromium . .
Sulphur . . . 0.240 0.330 Molybdenum :
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 38 of 44
Description:4130-CR-BR-SQ-AN-AR-N/A Mtl Group:Alloy Steel Material: 4130 Mtl Spec Code:47 Final Processing: Cold rolled. Mtl Form: Bar Quality: Special Quality Temper: Annealed Surface : As Rolled Edge Condition: Not Applicable Gen Spec: ASTM A 505 Addnl. Spec: ASTM 506 Exception: No Exceptrions Grain Size: 6 -9 Grain Size Note: Grain size of the material should be predominately equiaxed with t he range specified above. Grain size shall be determined in accord ance with ASTM E112. Hardness: 85 HRB Max
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.280 0.330 Silicon . . . 0.150 0.350
Manganese . : 0.400 0.600 Nickel . . .
Phosphorus . 0.035 Chromium . . 0.800 1.100
Sulphur . . . 0.035 Molybdenum : 0.150 0.250
Aluminum . . Boron . . . .
Microstructure: Minimum 90% spheroidal carbide structure with no evidence of lamellar or disintegrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 39 of 44
Description:4130-CR-ST-SQ-AN-S1-No.3 Mtl Group:Alloy Steel Material:4130 Mtl Spec Code:41
Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 505 Addnl. Spec: ASTM 506 Exception: No Exceptrions Grain Size: 6 -9 Grain Size Note: Grain size of the material should be predominately equiaxed with t he range specified above. Grain size shall be determined in accord ance with ASTM E112. Hardness: 85 HRB Max
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.280 0.330 Silicon . . . 0.150 0.350
Manganese . : 0.400 0.600 Nickel . . .
Phosphorus . 0.035 Chromium . . 0.800 1.100
Sulphur . . . 0.035 Molybdenum : 0.150 0.250
Aluminum . . Boron . . . .
Microstructure: Minimum 90% spheroidal carbide structure with no evidence of lamellar or disintegrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 40 of 44
Description:4130-CR-ST-SQ-AN-S2-No.3 Mtl Group:Alloy Steel Material:4130 Mtl Spec Code:43 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Annealed Surface : Bright Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 505 Addnl. Spec: ASTM 506 Exception: No Exceptrions Grain Size: 6 -9 Grain Size Note: NOTE: Grain size of the material should be predominately equiaxed with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: 85 HRB Max
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.280 0.330 Silicon . . . 0.150 0.350
Manganese . : 0.400 0.600 Nickel . . .
Phosphorus . 0.035 Chromium . . 0.800 1.100
Sulphur . . . 0.035 Molybdenum : 0.150 0.250
Aluminum . . Boron . . . .
Microstructure: Minimum 90% spheroidal carbide structure with no evidence of lamellar or disintegrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 41 of 44
Description:4130-CR-ST-SQ-DSA-S1-No.3 Mtl Group:Alloy Steel Material:4130 Mtl Spec Code:28 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Double Spheroidized Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 505 Addnl. Spec: ASTM A506 Exception: No Exceptions. Grain Size: Si Killed, 6-9 Grain Note: NOTE: Grain size of the material should be predominately equiaxed Size with the range as specified above. Grain size shall be determine d in accordance with ASTM E112. Hardness: 80 HRB MAX
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and plating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.280 0.330 Silicon . . . 0.150 0.350
Manganese . : 0.400 0.600 Nickel . . .
Phosphorus . 0.035 Chromium . . 0.800 1.100
Sulphur . . . 0.035 Molybdenum : 0.150 0.250
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 95% spheroidal carbide structure with no evidence of lamellar pearlite or disintegrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 42 of 44
Description:4130S-CR-ST-SQ-AN-S1-No.3 Mtl Group:ALLOY STEEL Material:4130S Mtl Spec Code:15 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Annealed Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 505 Addnl. Spec: ASTM A506 Exception: No Exceptions Grain Size: Si Killed, 6-9 Grain Note: NOTE: Grain size of the material should be predominately equiaxed Size with the range as specified above. Grain size shall be determined in accordance with ASTM E112. Hardness: 85 HRB MAX
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and p lating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.280 0.330 Silicon . . . 0.150 0.350
Manganese . : 0.400 0.600 Nickel . . .
Phosphorus . 0.035 Chromium . . 0.800 1.100
Sulphur . . . 0.035 Molybdenum : 0.150 0.250
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 43 of 44
Description:4130S-CR-ST-SQ-AN-S2-No.3 Mtl Group:ALLOY STEEL Material:4130S Mtl Spec Code:26 Final Processing: Cold rolled. Mtl Form: Strip Quality: Special Quality Temper: Annealed Surface : Bright Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: ASTM A 505 Addnl. Spec: ASTM A506 Exception: No Exceptions Grain Size: Si Killed, 6-9 Grain Note: NOTE: Grain size of the material should be predominately equiaxed Size with the range as specified above. Grain size shall be determined in accordance with ASTM E112. Hardness: 85 HRB MAX
Fitness Fitness Note: Fitness For Use: This material must be fit for blanking, forming, heat treating, and plating processes. The end product will be utilized in an occupant restraint system. Std Min Max Std Min Max
Carbon . . . 0.280 0.330 Silicon . . . 0.150 0.350
Manganese . : 0.400 0.600 Nickel . . .
Phosphorus . 0.035 Chromium . . 0.800 1.100
Sulphur . . . 0.035 Molybdenum : 0.150 0.250
Aluminum . . Boron . . . .
Microstructure: NOTE: Minimum 90% spheroidal carbide structure with no evidence of lamellar pearlite or dis
integrating plates.
Material Specifications for Steel Revision Date: June 9, 2010
Material shall be free of pits, laminations and any other surface imperfections, consistent with industry standards for the quality specified, which may be detrimental in the manufacture of the product for which the material is intended. Continuous cast material is preferred. Steel mill heat number, chemistry and master coil number used to manufacture the component lot number of each shipment must be certified per IMMI Procedure QA-33. IMMI Bringing Safety to People™
Page 44 of 44
Description:MCSL-CR-ST-CQ-T3-S1-No.3 Mtl Group:Medium Carbon Steel Material:MCSL Mtl Spec Code:16 Final Processing: Cold rolled. Mtl Form: Strip Quality: Commercial Quality Temper: Quarter Hard Surface : Dull Edge Condition: Approx. square edge by slitting, not filing. Gen Spec: Addnl. Spec: Exception: Grain Size: Note: Hardness: 60 - 75 HRB
Fitness Note: Std Min Max Std Min Max
Carbon . . . Silicon . . .
Manganese . : Nickel . . .
Phosphorus . Chromium . .
Sulphur . . . Molybdenum :
Aluminum . . Boron . . . .
Microstructure: