Portland State University Portland State University
PDXScholar PDXScholar
Undergraduate Research & Mentoring Program Maseeh College of Engineering & Computer Science
5-2017
Design and Test of 3D Printed Lenses for sub-THz Design and Test of 3D Printed Lenses for sub-THz
Radiation Radiation
Justin Patterson Portland State University
Follow this and additional works at: https://pdxscholar.library.pdx.edu/mcecs_mentoring
Part of the Electrical and Computer Engineering Commons
Let us know how access to this document benefits you.
Citation Details Citation Details Patterson, Justin, "Design and Test of 3D Printed Lenses for sub-THz Radiation" (2017). Undergraduate Research & Mentoring Program. 13. https://pdxscholar.library.pdx.edu/mcecs_mentoring/13
This Poster is brought to you for free and open access. It has been accepted for inclusion in Undergraduate Research & Mentoring Program by an authorized administrator of PDXScholar. Please contact us if we can make this document more accessible: [email protected].
Design and Test of 3D Printed Lenses for sub-THz Radiation By Justin Patterson, Prof. Branimir Pejcinovic
Introduction
Lens Design
Measurement Setup
Material Characterization
References
Gaussian Beam Analysis
Acknowledgements
In order to manipulate sub-THz radiation we investigated production of in-
expensive lenses. Production of such lenses were made using additive 3D
printing. With rising 3D printing technology, fabrication of optical compo-
nents transparent to the THz regime is made more accessible. Lenses were
designed using a CAD software, Onshape, and Polypropylene was selected
as the material of choice. The resulting radiation was characterized using
Gaussian beam analysis.
The authors acknowledge the support of the Semiconductor Research Cor-
poration (SRC) Education Alliance (award # 2009-UR-2032G) and of the
Maseeh College of Engineering and Computer Science (MCECS) through
the Undergraduate Research and Mentoring Program (URMP)
The receiving horn was swept
(varying the radial distance) to
observe the E-field amplitude.
MATLAB cftool was used to
fit the Gaussian profile, and the
resulting waveform was then
centered and normalized
Gaussian Beam Theory
Virginia Diodes continuous wave system setup for 150 GHz:
(1): Transmitter (3): Off-axis parabolic mirror
(2): Receiver (4): Plano-convex lens
[1] S.F. Busch, et al. “Optical Properties of 3D Printable Plastics in the
THz Regime and their Application of 3D Printed THz Optics,” J Infrared
Milli Terahz Waves, vol. 35, no. 12, pp. 993-997, Dec. 2014.
[2] Hecht, Eugene. Optics. 4th ed. Reading: Addison-Wesley, 2002. Print.
[3] A. Kazemipour, et al. “The Horn Antenna as Gaussian Source in the
mm-Wave Domain,” J Infrared Milli Terahz Waves, vol. 35, no. 9, pp. 720–
731, Sep. 2014.
Plano-convex lenses were designed using the lens-maker equation.
The beam waist () was calculated at multiple distances (z) by varying the
distance between the lens and the receiving horn. The minimum beam
waist (0) of 7.5 in, corresponds to the focal length of the lens.
(1): 3 inch lens with focal length and
curvature of 5.6 and 2.97 in, respec-
tively. Used with the VDI system
(2): 1.5 inch lens with focal length and
curvature of 3.6 and 1.91 in, respec-
tively. Used with the TDS system
(3): CNC routed Polypropylene lens
Gaussian distribution (left figure): The E-field intensity (I) varies with ra-
dial distance (r) away from the center. The beam waist () is located where
I is 14% of maximum value [2]
Gaussian beam propagation (right figure): Varying as the beam propa-
gates in the z-direction. 0 denotes the minimum beam waist [3]
Polypropylene shows less-loss at THz frequencies compared to ABS.
HDPE carries ideal characteristics; however, it is a challenge to 3D print
due to warping. The absorption coefficient of PP is under 2 cm^(-1) for
frequencies below 1 THz, and the refractive index, n, was approximately
1.53-1.55 for the sub-THz band