DESIGN OF DIELECTRIC RESONATOR ANTENNA
ARRAYS FOR WIRELESS APPLICATIONS
A THESIS SUBMITTED IN PARTIAL FULFILLMENT OF THE
REQUIREMENTS FOR THE DEGREE OF
MASTER OF TECHNOLOGY
IN
COMMUNCATION AND SIGNAL PROCESSING
BY
IMRAN KHAN
211EC4104
DEPARTMENT OF ELECTRONICS AND COMMUNICATION
ENGINEERING
NATIONAL INSTITUTE OF TECHNOLOGY ROURKELA-769008
2013
DESIGN OF DIELECTRIC RESONATOR ANTENNA
ARRAYS FOR WIRELESS APPLICATIONS
A THESIS SUBMITTED IN PARTIAL FULFILLMENT OF THE
REQUIREMENTS FOR THE DEGREE OF
MASTER OF TECHNOLOGY
IN
COMMUNCATION AND SIGNAL PROCESSING
BY
IMRAN KHAN
211EC4104
UNDER THE GUIDANCE OF
PROF. S K BEHERA
DEPARTMENT OF ELECTRONICS AND COMMUNICATION
ENGINEERING
NATIONAL INSTITUTE OF TECHNOLOGY ROURKELA-769008
2013
DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING
NATIONAL INSTITUTE OF TECHNOLOGY ROURKELA
Date: 21-05-1013
CERTIFICATE
This is to certify that the thesis entitled, “Design of Dielectric resonator antenna arrays for
wireless applications” submitted by Mr. IMRAN KHAN in partial fulfillment of the
requirements for the award of Master of Technology Degree in Electronics and Communication
Engineering with specialization in “Communication and Signal Processing” during session
2012-2013 at the National Institute of Technology, Rourkela (Deemed University) is an
authentic work carried out by him under my supervision and guidance. To the best of my
knowledge, the matter embodied in the thesis has not been submitted to any other University/
Institute for the award of any degree or diploma.
S.K.BEHERA
ACKNOWLEDGEMENTS
This project is by far the most significant accomplishment in my life and it would be impossible
without people who supported me and believed in me.
I would like to extend my gratitude and my sincere thanks to my honorable and esteemed
supervisor Prof. S K Behera. He is not only a great teacher/professor with deep vision but also a
kind person. I sincerely thank him for his exemplary guidance and encouragement. His trust and
support inspired me in the most important moments of making right decisions and I am glad to
work with him. My special thank goes to Prof. S K Meher Head of the Department of Electronics
and Communication Engineering, NIT, Rourkela, for providing us with best facilities in the
Department and his timely suggestions.
I want to thank all my teachers Prof. S.K. Patra, Prof. K.K. Mahapatra, Prof. A.K. Sahoo,
and Prof. P. Singh for providing a solid background for my studies and research thereafter. They
have been great sources of inspiration to me and I thank them from the bottom of my heart. I
would also like to thank Ms. Runa Kumari, Mr S. Natrajmani and Mr. Yogesh Choukiker for
their valuable suggestions from time to time.
I am forever grateful to all my friends and especially to Lucky Kodwani, who gently offer
counsel and unconditional support at each turn of the road. I have enjoyed their companionship a
lot during my stay at NIT, Rourkela. I would like to thank all those who made my stay in
Rourkela an unforgettable and rewarding experience.
Last but not least I would like to thank my parents, who taught me the value of hard work
by their own example. They rendered me enormous support during the whole tenure of my stay
in NIT Rourkela.
IMRAN KHAN
i
CONTENTS
CHAPTER-1: THESIS OVERVIEW ................................................................................................... 1
1.1 THESIS MOTIVATION: ............................................................................................................... 2
1.2 LITERATURE REVIEW:.............................................................................................................. 2
1.3 SCOPE OF THIS PROJECT: ......................................................................................................... 3
1.4 INTRODUCTION TO WLAN AND WIMAX: .............................................................................. 4
1.5 THESIS OUTLINE: ...................................................................................................................... 4
CHAPTER-2: DIELECTRIC RESONATOR ANTENNA.................................................................... 6
2.1 INTRODUCTION: ........................................................................................................................ 7
2.1.1 MAJOR CHARACTERESTICS: ................................................................................................ 8
2.1.2 LIMITATIONS: ......................................................................................................................... 9
2.1.3 APPLICATIONS: ....................................................................................................................... 9
2.2 FEEDING METHODS: ............................................................................................................. 10
2.2.1 MICROSTRIP FEED: .............................................................................................................. 10
2.2.2 COAXIAL/PROBE FEED: ...................................................................................................... 11
2.2.3 APERTURE FEED: ................................................................................................................. 12
2.2.4 PROXIMITY COUPLED MICROSTRIP FEED: ..................................................................... 14
2.2.5 COPLANAR FEED: ................................................................................................................ 14
2.2.6 DIELECTRIC IMAGE GUIDE FEED: .................................................................................... 15
2.3 TRANSMISSION LINE MODELING: ........................................................................................ 17
2.4 RECTANGULAR DIELECTRIC RESONATOR ANTENNA DESIGN: ..................................... 19
2.5 NOTCHED RECTANGULAR DRA: .......................................................................................... 21
2.6 CHAMFERED RECTANGULAR DRA: ..................................................................................... 23
CHAPTER-3: DRA ARRAY ............................................................................................................. 24
3.1 DRA ARRAY THEORY: ............................................................................................................ 25
3.2 ARRAY THEORY: ..................................................................................................................... 25
3.3 FEED NETWORK FOR DRA ARRAY: ..................................................................................... 26
3.4 MUTUAL COUPLING: .............................................................................................................. 28
CHAPTER-4: NOTCHED CHAMFERED RECTANGULAR DRA .................................................. 30
4.1 INTRODUCTION: ...................................................................................................................... 31
4.2 ANTENNA DESIGN:.................................................................................................................. 31
ii
4.3 RESULTS AND DISCUSSION: .................................................................................................. 34
4.3.1 PARAMETRIC STUDY: .......................................................................................................... 34
4.3.2 GAIN CHARACTERESTICS: .................................................................................................. 36
4.3.3 RADIATION PATTERN CHARACTERISTICS: ..................................................................... 36
4.4 CONCLUSION: .......................................................................................................................... 38
CHAPTER-5: TWO ELEMENT RDRA ............................................................................................ 39
5.1 INTRODUCTION: ...................................................................................................................... 40
5.2 ANTENNA DESIGN:.................................................................................................................. 40
5.3 RESULTS AND DISCUSSIONS:................................................................................................ 43
5.3.1 PARAMETRIC STUDY: .......................................................................................................... 43
5.3.2 GAIN CHARACTERISTICS: ................................................................................................... 45
5.3.3 RADIATION PATTERN CHARACTERISTICS: ..................................................................... 46
5.4 CONCLUSION: .......................................................................................................................... 47
CHAPTER-6: FOUR ELEMENT RDRA ARRAY ............................................................................ 48
6.1 INTRODUCTION: ...................................................................................................................... 49
6.2 ANTENNA DESIGN:.................................................................................................................. 49
6.3 RESULTS AND DISCUSSIONS:................................................................................................ 51
6.3.1 PARAMETRIC STUDY: .......................................................................................................... 51
6.3.2 GAIN AND DIRECTIVITY CHARACTERISTICS: ................................................................ 53
6.3.3 VSWR CHARACTERISTICS: ................................................................................................. 54
6.3.4 RADIATION PATTERN CHARACTERISTICS: ..................................................................... 54
6.4 CONCLUSION: .......................................................................................................................... 57
CHAPTER-7: CONCLUSION & FUTURE WORK .......................................................................... 58
iii
ABSTRACT
This thesis presents design of dielectric resonator antenna array for wireless applications. Three
antenna designed are presented in the following sections. The first design is a notched chamfered
two element rectangular dielectric resonator antenna (DRA) array for wireless (WLAN and
WIMAX) applications. Here the DRA array is excited by conformal patch connected to
microstrip line which is an effective feed mechanism and more efficient in energy coupling than
other types of feeding techniques. The shape is notched and chamfered to improve the
performance of the antenna. From the Simulation results it can be observed that the proposed
antenna covers 2.4, 3.6 and 5 GHz WLAN bands and 3.4 to 3.7 GHz WIMAX bands, achieving
an impedance bandwidth from 2.18 to 3.75 GHz and 4.84 to 5.14 GHz. Parametric study is done
by varying the shapes of the rectangular DRA arrays (Simple Rectangle, chamfered and
chamfered with notched). Another parametric study is carried out by varying the dimension of
the ground plane of the final design. The proposed antenna design gives the appreciable gain and
radiation pattern at the resonant frequencies.
The second design is a rectangular shaped two element Dielectric Resonator Antenna
(DRA) array for 2.4 GHz WLAN application. Here microstrip feed line in corporate (parallel)
arrangement is used for feeding. Simulation result shows that the antenna achieves a bandwidth
from 2.1 to 3 GHz, covering the 2.4 GHz WLAN band. Here the parametric study is done by
varying the feed line and the ground plane of the antenna. The simulation results as well as the
parametric studies are incorporated in this thesis.
The third one is the Design of four element rectangular shaped dielectric resonator
antenna (RDRA) array for wireless applications. The RDRA array is fed by rectangular
conformal patch (RCP) connected to microstrip line. Simulation result shows that the proposed
antenna achieves an impedance bandwidth from 4 GHz to 7.1 GHz covering various wireless
bands. Parametric studies have been carried out by varying the RCP height and the ground plane
of the final design. The proposed antenna design gives the appreciable gain and better radiation
pattern at the resonant frequencies.
iv
TABLE OF FIGURES
Fig.1 DRAs of various shapes .....................................................................................................8
Fig.2 Microstrip feed ................................................................................................................. 11
Fig.3 Probe feed ........................................................................................................................ 12
Fig.4 Aperture feed ................................................................................................................... 13
Fig.5 Coplanar feed ................................................................................................................... 15
Fig.6 Dielectric image guide feed .............................................................................................. 16
Fig.7 Equivalent circuits for some typical feeding techniques .................................................... 17
Fig.8 (a) Microstrip line and (b) Electric field lines ................................................................... 18
Fig.9 Geometry of rectangular DRA .......................................................................................... 20
Fig.10 Notched rectangular DRA .............................................................................................. 22
Fig.11 Chamfered rectangular DRA .......................................................................................... 23
Fig.12 (a) Series and (b) Corporate feed .................................................................................... 27
Fig.13 Perspective view of rectangular DRA ............................................................................. 32
Fig.14 (a) Front view, (b) Perspective and (c) Rear view of the notched chamfered DRA array . 33
Fig.15 Comparison of S-parameter of different shapes of DRAs................................................ 34
Fig.16 Comparison of S-parameter by taking different Lg values ............................................... 35
Fig.17 Simulated Gain vs. Frequency curve for 2.4, 3.6 and 5 GHz ........................................... 36
Fig.18 Simulated Radiation pattern of proposed DRA array at (a) 2.4 GHz (b) 3.6 GHz and (c) 5
GHz .......................................................................................................................................... 38
Fig.19 (a) Front (b) Perspective and (c) Rear view of the two element RDRA array .................. 42
Fig.20 (a) Front view and (b) Rear view of the fabricated antenna ............................................. 43
Fig.21 Comparison of S-parameters for different L2 values ....................................................... 44
Fig.22 Comparison of S-parameters for different Lg values ....................................................... 44
Fig.23 Measures S-parameter of the fabricated antenna ............................................................. 45
Fig.24 Simulated Gain vs. Frequency curve .............................................................................. 46
Fig.25 Simulated Radiation pattern for 2.4 GHz ........................................................................ 47
Fig.26 (a) Front view (b) Perspective view (c) Rear view of the four element RDRA array ....... 51
Fig.27 Comparison of S-parameter for different RCP values ..................................................... 52
Fig.28 Comparison of S-parameter for different Wg values ........................................................ 52
Fig.29 Gain and Directivity curves for the RDRA array ............................................................ 53
Fig.30 VSWR vs Frequency curve ............................................................................................ 54
Fig.31 Radiation pattern of the RDRA Array at (a) 4.2 (b) 5.2 (c) 6.2 and (d) 7 GHz................. 56
1
CHAPTER-1: THESIS
OVERVIEW
2
1.1 THESIS MOTIVATION:
Bandwidth enhancement is one of the major design considerations for most practical applications
of Dielectric resonator antennas. Microstrip antennas have some limitations compared to
dielectric resonator antennas as narrow bandwidth, lower gain, lower power handling capacity
etc. For that reason, dielectric resonator antennas are preferred over microstrip and conventional
antennas. In recent few decades, research scientists have developed several techniques to
increase the bandwidth and obtain multi band response for an antenna. Making DRA arrays by
using different types of feeding techniques is one of the most popular bandwidth enhancement
approach. The recent advancements in wireless communication industry, especially in the area of
mobile communication and wireless data communication, have led to the increased demand for
multi band antennas, which promoted the study and design of DRA arrays.
1.2 LITERATURE REVIEW:
For many years, the dielectric resonator (DR) has primarily been used in microwave circuits,
such as oscillators and filters [1]. Because of these traditional applications, the DR was usually
treated as energy storage device. Dielectric resonator was first discussed as an antenna by S. A.
Long in a paper entitled, “The resonant cylindrical dielectric cavity antenna,” IEEE Transactions
on Antenna and Propagations [2]. At that time, it was observed that the frequency range of
interest for many systems has gradually progressed upward to the millimeter and near millimeter
range (100–300 GHz). The conductor loss of metallic antennas becomes severe and the
efficiency of the antenna is reduced significantly at these frequencies. But the only loss for a
DRA is that due to the imperfect dielectric material, and its value is almost negligible. After the
cylindrical DRA has been studied, Long and his colleagues subsequently investigated the
rectangular and hemispherical DRAs [3], [4]. Analysis of their resonant modes, radiation
patterns, and method of excitation made it clear that these dielectric resonators could be used as
antennas and offered a new and attractive alternative to traditional low gain radiators. In the early
1990, emphasis was placed on realizing various analytical or numerical techniques for
determining the input impedance and Q-factor. Focus was mainly on individual elements. A
significant amount of this characterization was carried out by two research teams; one was led by
Kishk, Glisson, and Junker and the other by Luk and Leung. Much of the early work to
characterize the performance of the basic DRA elements was summarized in a 1994 review paper
3
by Mongia and Bhartia [5]. They also proposed different modes for DRA, and provided a set of
simple equations for predicting the resonant frequency and the Q-factors for several DRA
shapes. By the mid-1990s more attention was being given to linear and planar DRA arrays,
ranging from simple two element arrays, up to complex phased arrays of over 300 elements with
beam-steering capability. The development of ferrite resonator antennas, DRAs operating at 40
GHz, and DRAs with nearly 40% impedance bandwidth also occurred in this period. Many of
the recent advances were reported in a 1998 paper by Petosa et al. [6]. K. W. Leung proposed a
new excitation scheme in year 2000 which employs a conducting conformal strip for dielectric
resonator antenna excitation by using a hemispherical DRA [7]. M.S.M. Aras, M.K.A. Rahim,
Z.Rasin, M.Z.A. Abdul Aziz proposed an array of Dielectric resonator Antenna for wireless
application in 2008 [8]. Wael M. Abdel Wahab, Safieddin Safavi Naeini, and Dan Busuioc
Modelled and Designed a Millimeter-Wave High Q-Factor Parallel Feeding Scheme for
Dielectric Resonator Antenna Arrays in 2011 [9]. Yong Mei Pan, Kwok Wa Leung and Kai Lu
Proposed Omnidirectional Linearly and Circularly Polarized Rectangular Dielectric Resonator
Antennas in 2012 [10].
1.3 SCOPE OF THIS PROJECT:
The scope of this work is to design and fabricate dielectric resonator antenna arrays which can be
used for wireless applications according to IEEE 802.11 and 802.16 standards. The operating
frequency band must cover the 2.4, 3.6, 4.9 and 5 GHz WLAN bands covered by IEEE 802.11
standards and 2.3, 2.5, 3.5 and 5.8 GHz WIMAX bands covered by 802.16 standards. The
antenna should be small in size and easy to manufacture with available laboratory equipments.
The return loss must be less than -10 dB within the wireless range, which means only 10% of
power will be reflected back while 90% of power is transmitted. Other aspects, such as beam
width, side lobes and directivity, were not considered during the design stage; but, they were
evaluated for the final designs.
Special attention had been paid to the feeding techniques used, as it is a very important
parameter in the design of the dielectric resonator antenna array. Corporate feeding techniques
with matched lines are used for the purpose.
4
1.4 INTRODUCTION TO WLAN AND WIMAX:
Wireless communications have grown at a very rapid pace across the world over the last few
years, which provide a great flexibility in the communication infrastructure of environments such
as hospitals, factories, and large office buildings. WLAN and WIMAX are the standard based
technologies enabling the delivery of the wireless broadband access. A wireless local area
network (WLAN) links two or more devices using wireless distribution method and provide a
connection through an access point to the wider internet. By this a user has the mobility to move
around a local coverage area and still be connected to the network. WLANs are based on IEEE
802.11 standards, marketed under the Wi-Fi brand name. The 802.11 covers mainly three
different frequency range. Those are 2.4 GHz, 3.6 GHz and 4.9/5 GHz. The 2.4 GHz channel
comes under 802.11b/g/n standards, 3.6 GHz comes under 802.11y standard, 4.9 GHz frequency
comes under 802.11y and 5 GHz frequency is included in 802.11a/h/j/n standards. In WLAN a
number of standards have been defined in the 5 to 6 GHz range that allow data rates greater than
20 Mb/s, which offers attractive solutions for real-time imaging, multimedia, and high speed
video applications.
Worldwide Interoperability for Microwave Access (WIMAX) is a wireless
communication standard to provide higher data rates. WIMAX refers to interoperable
implementations of the IEEE 802.16 family of wireless network standards. WIMAX can provide
at home or mobile Internet access across whole cities or countries. Now a days WIMAX is used
to provide internet access in remote places at a low cost. It can operate over higher bit rates and
longer distances. The bandwidth and range of WIMAX make it suitable for providing portable
mobile broadband connectivity across cities and countries, to provide broad band internet access
and for data and telecommunication services. The frequencies included in 802.16 standards are
2.3, 2.5, 3.5 and 5.8 GHz which have many practical applications [11].
1.5 THESIS OUTLINE:
In Chapter 1 the thesis overview is shown. The literature review for the project work is done in
this chapter and the introduction to WLAN and WIMAX and its different standards are shown in
this chapter. Chapter 2 presents the basic theory of DRAs, including the characteristics of the
DRAs, its advantages and its applications, Comparison to microstrip antennas and different
5
feeding methods (coaxial feed, slot aperture, microstrip line feed, proximity coupled microstrip
line feed, co-planar feed & dielectric image guide). It also shows some of the equivalent circuits
of the feed line and transmission line modeling for microstrip feed design. At last this chapter
shows the study of rectangular DRA and some of its modified shapes for bandwidth
enhancement. Chapter 3 focuses on the study of DRA array and shows the different feeding
techniques for DRA arrays. It also shows the study of mutual coupling between the resonating
elements and how to avoid its occurrence.
Chapter 4 describes the design of a notched chamfered rectangular dielectric resonator
antenna for WLAN and WIMAX applications. In this design, the DRA array is excited by
conformal patch connected to microstrip line which is an effective feed mechanism and more
efficient in energy coupling than other types of feeding techniques. In chapter 5 design of two
elements rectangular shaped dielectric resonator antenna (RDRA) array is presented for 2.4 GHz
wireless applications. The RDRA array is excited by microstrip line coupling arranged in a
corporate feed technique. Simulation result shows that the proposed antenna achieves an
impedance bandwidth from 2.1 GHz to 3 GHz covering 2.4 GHz wireless band. The fabricated
antenna and its measured reflection coefficient vs. frequency curve is also shown in this chapter.
Chapter 6 presents a four element rectangular shaped dielectric resonator antenna (RDRA) for
wireless applications. The RDRA array is excited by rectangular conformal patch (RCP)
connected to microstrip line. Simulation results have been shown for this design.
Conclusion of the thesis is given in chapter 7 and the future work of the DRA array is
shown in this chapter.
6
CHAPTER-2: DIELECTRIC
RESONATOR ANTENNA
7
2.1 INTRODUCTION:
Dielectric resonator antenna consists of dielectric materials in its radiating patch also called as
dielectric resonators (DRs) on one side of the substrate and has a ground plane (metal) on the
other side [12], [13]. The dielectric constant of the dielectric resonators on the DRAs can vary
from 2 to 100. The dielectric resonators have three basic shapes i.e. circular, rectangular and
triangular, but rectangular shape is generally used because the design and analysis of rectangular
shape is comparatively easy [3], [4]. As compared to the microstrip antenna, the DRA has a
much wider impedance bandwidth (~10% for dielectric constant ɛr ~ 10). This is because the
microstrip antenna radiates only through two narrow radiation slots, whereas the DRA radiates
through the whole DRA surface except the ground part [12]. Avoidance of surface waves is
another attractive advantage of the DRA over the microstrip antenna. However, many
characteristics of the DRA and microstrip antenna are common because both of them behave like
resonant cavities. For example, since the dielectric wavelength is smaller than the free-space
wavelength by a factor of
√ , both of them can be made smaller in size by increasing [12],
[13]. Preferably, the relative permittivity ɛr of the substrate should be low (ɛr < 2.5), to enhance
the fringing fields that account for the radiation. However, as per the performance requirements,
the value of the dielectric constant of the substrate may vary and can be of some greater value
(say 4.4). Various types of substrates having a large range of dielectric constant and loss tangent
values have been developed. Sometimes if we increase the dielectric constant or relative
permittivity of the substrate or the dielectric resonators (DRs) there is chance to increase the
performance of the antenna, but materials with higher dielectric constant values may or may not
be available for fabrication. Fig.1 shows the basic shapes of the DRAs. There are a number of
effective excitation methods that can be used for DRAs. Some of the examples are the coaxial
probe, aperture-coupling with a microstrip feed line, aperture-coupling with a coaxial feed line,
direct microstrip feed line, co-planar feed, soldered-through probe, slot line, strip line, proximity
coupled microstrip feed, conformal strip, and dielectric image guide feed[12], [22], [23].
Microstrip feeding technique is most general and simple method of feeding. Here the DRAs are
fed with 50 Ω microstrip lines.
8
Fig.1 DRAs of various shapes
2.1.1 MAJOR CHARACTERESTICS:
Some of the main characteristics of the dielectric resonator antennas are summarized below;
1. The size of the DRA is proportional tor 0
, where is the free space wavelength at the
resonant frequency, and ɛr is the dielectric constant of the material.
2. The resonant frequency and radiation Q-factor is also affected by the aspect ratio of the DRA
for a fixed dielectric constant, permitting additional design flexibility to the designers.
3. A wide range of dielectric constants can be used allowing the designers to control the physical
size and the bandwidth of the DRA.
4. By selecting a dielectric material with low loss characteristics, a high radiation efficiency can
be maintained in DRAs.
9
5. DRAs can be designed to operate over a wide range of frequencies from 1 GHz to 44 GHz.
6. DRA has much wider impedance bandwidth compared to microstrip antennas.
7. Depending upon the resonator shape, various modes can be excited within the DRA producing
either broad side or omnidirectional radiation patterns for different coverage requirements.
8. DRAs have high dielectric strength and hence higher power handling capacity.
9. It has high degree of flexibility and versatility, allowing for designers to suit a wide range of
physical or electrical requirements of varied communication applications.
10. Several feeding methods can be used to efficiently excite the DRAs, such as probes,
microstrip lines, slots & dielectric image guides & co-planar wave guide lines [12], [13].
2.1.2 LIMITATIONS:
1. The fabrication price is more as compared to microstrip antenna.
2. Ceramic materials are typically used, which must either be machined from large blocks or cast
from molds. Drilling may be required and the DRA has to be bonded to a ground plane or
substrate.
3. Compared to the printed circuit antennas, the fabrication is generally more complex and more
costly, especially for array applications.
4. Difficult to get dielectric materials of desired dielectric constants, so have to work with limited
available sources.
5. Excitation of surface waves [12], [13].
2.1.3 APPLICATIONS:
1. Satellite communication, direct broadcast services.
2. Doppler and other radars.
3. Missiles and telemetry.
10
4. Mobile radio (pagers, telephones, man pack systems).
5. Biomedical radiators and intruder alarms.
2.2 FEEDING METHODS:
Feeding techniques are required to energize the antenna i.e. to transfer the power into the
antenna. Early microstrip antennas were fed either by a microstrip line or a coaxial probe through
the ground plane. Dielectric resonator antennas have radiating elements on one side of dielectric
substrate and for these designs a number of new feeding techniques have been developed [12],
[13]. Some feeding techniques are easy to fabricate where as other are difficult, and some
feeding techniques can enhance the bandwidth. For example, aperture and proximity feeds are
used to increase the bandwidth but fabrication is the major problem because these two feeding
techniques useful when two substrate are present.
2.2.1 MICROSTRIP FEED:
Excitation of the dielectric resonator antenna by a microstrip line on the same substrate is the
easiest method of feeding. In this type of feed technique, a conducting strip is connected directly
to the edge of the dielectric resonator (DR) or inserted under the DR. A common method of
excitation with microstrip line is to use it by proximity coupling. The amount of coupling from
the microstrip line to the DRA can be controlled to a certain degree by adjusting the spacing
between the DRA and the line for the side-coupled case or the length of the line underneath the
DRA for the direct-coupled case [12]. The dielectric constant of the DRA also affects the
coupling. Higher the value of dielectric constant, higher will be the value of the coupling. This is
an easy feeding scheme and it provides ease of fabrication and simplicity in modeling as well as
impedance matching. As the thickness of the dielectric substrate of the DRA increases, surface
waves and spurious feed radiation also increase, so the thickness of the substrate should be kept
less [12]-[15]. Fig.2 shows the microstrip feed technique to DRA.
11
Fig.2 Microstrip feed
2.2.2 COAXIAL/PROBE FEED:
Another common method of coupling to DRA is with a probe. The probe usually consists of the
center pin of a coaxial transmission line that extends through the ground plane. The center pin
can also be soldered to a flat metal strip that is placed adjacent to the DRA, whose length and
width can be adjusted to improve the impedance match [12], [13]. The coaxial connector is
attached to the back side of the DRA and the coaxial center conductor after passing through the
substrate is drilled into the dielectric resonators. The amount of coupling can be controlled by
adjusting the probe height and the DRA location. The probe length is generally chosen to be less
than the height of the DRA, to avoid probe radiation. Feeding the probe adjacent to the DRA is
12
preferred since it does not require drilling into the DRA. The advantage of the coaxial probe
excitation is the direct coupling into a 50-Ω system without the need for a matching network
[16], [17]. Fig.3 shows the probe coupling to the DRA.
·
Fig.3 Probe feed
2.2.3 APERTURE FEED:
One common method of exciting a DRA is through an aperture in the ground plane upon which
the DRA is placed. Small rectangular slot is the most widely used aperture [12], [13], [18]. By
keeping the slot dimensions electrically small, the amount of radiation beneath the ground plane
can be minimized. Annular slots are generally used for exciting cylindrical DRAs, while cross-
shaped and C-shaped slots are used to excite circular polarization. The aperture can be fed by a
transmission line (either microstrip or coaxial) or a waveguide. Aperture coupling offers the
13
advantage of having the feed network located below the ground plane, isolating the radiating
aperture from any unwanted coupling or spurious radiation from the feed [12]. Feeding the
aperture with a microstrip transmission line is the most common approach, since printed
technology is easy to fabricate. Microstrip line also offers a degree of impedance matching not
available with coaxial lines or waveguides [19]-[21]. Fig.4 shows the aperture coupling to the
DRA.
Fig.4 Aperture feed
14
2.2.4 PROXIMITY COUPLED MICROSTRIP FEED:
In this type of feeding we use a two layer substrate and the DRA is placed on the upper layer.
This feed is also known as an electromagnetically coupled feed. To design this feed Two
substrates are required, and the feed line shoud be in between the two substrates. The fabrication
of the antenna is difficult and the thickness of the antenna is increased due to the presence of two
substrates. By using this feeding technique The bandwidth of the antenna can be improved. The
substrate parameters of the two layers can be selected to increase the bandwidth and to reduce
spurious radiation, for this the lower substrate should be kept thin [22], [23]. The equlent circuit
diagram for this type of feeding is shown in fig.7 which consists of inductor, capcitor & resistors.
Proximity-coupled microstrip antenna is also known as non-contacting feeds.
Some advantages are:
No physical contact between feed line and radiating element
No drilling required.
Less spurious radiation.
Better for array configurations.
Good suppression of higher order modes
Better high frequency performance
2.2.5 COPLANAR FEED:
Coupling to DRAs can also be achieved by using coplanar feeds. Open-circuited waveguides can
be used to directly feed the DRAs. Additional control for impedance matching can be achieved
by adding stubs or loops by the end of the line. Fig.5 shows a cylindrical DRA coupled to a co-
planar loop. The coupling level can be increase or decrease by positioning the DRA over the
loop and by moving the loop from the edge of the DRA to the center. The dimensions of the
coplanar feed should be chosen large enough to ensure proper coupling, but small enough to
avoid excessive radiation in the back lobe [12], [13]. The coupling behavior of the co-planar loop
is similar to coaxial probe, but the loop offers the advantage of being non-obtrusive. [18], [24].
15
Fig.5 Coplanar feed
2.2.6 DIELECTRIC IMAGE GUIDE FEED:
This coupling technique is similar to microstrip line coupling, but instead of perfect electric
conductor we use dielectric material as feed line. Dielectric image guides offer advantages over
microstrips at millimeter-wave frequencies, since they do not suffer from conductor losses. The
coupling can be controlled by adjusting the spacing between the guide and the DRs [12], [13],
[18], [25]. Fig.6 shows the dielectric image guide coupling of the DRA.
16
Fig.6 Dielectric image guide feed
17
Fig.7 shows the equivalent circuits of some of the feeding techniques used for DRAs.
Fig.7 Equivalent circuits for some typical feeding techniques
2.3 TRANSMISSION LINE MODELING:
Transmission line model is the easiest modelling technique for microstrip antennas, but it yields
the least accurate results and it lacks the versatility. However, it does gives a good understanding
on microstrip line. Here in case of DRA this model is generally used to design and analyse the
microstrip line feeding. A rectangular microstrip antenna can be represented as an array of two
radiating narrow apertures (slots), each of width W and height h, seperated by a distance L. A
18
typical microstrip line is shown in Fig.8(a) while the electric field lines associated with it are
shown in Fig.8(b).
Fig.8 (a) Microstrip line and (b) Electric field lines
As L/h >>1 and ɛr>>1,the elctric field lines concentrate mostly in the substrate. The Fringing
effect in this case makes the microstrip look wider elctrically comapred to its actual physical
size. Since some of the waves travel in the substrate and some in air, an effective dielectric
constant ɛreff is introduced to account for fringing and the wave propogation in the line.
For a design with air gap above the substrate, the effective dielectric constant has values
in the range of 1< ɛreff< ɛr. For most applications where the dielectric constant of the substrate is
much greater than unity (ɛr>>1), the value of ɛreff will be closer to the value of the actual
dielctric constant ɛr of the substrate
When
H
W< 1
[( (
))
( (
))
]
(a) (b)
19
When (
)
( (
))
2.4 RECTANGULAR DIELECTRIC RESONATOR ANTENNA DESIGN:
The DRA with a rectangular crossection is known as the rectangular DRA. It is characterized by
a height h, width w, depth d, and a dielectric constant ɛr. The rectangular DRA is considered to
be a truncated section of an infinite dielectric waveguide of width w and height b = 2h due to the
image effect of the ground plane. Fig.9 shows the geometry of a rectangular DRA. The
rectangular shape offers a second degree of freedom because the w/h and w/d ratios can be
choosen independently, making it the most versatile of the basic shapes [12], [13]. By using this
design flexibility, we can achieve the desired profile and bandwidth characteristics for a given
resonant frequency and dielectric constant. In a rectangular DRA perfect magnetic walls are
assumed along the four surfaces parallel to the direction of propagation in the dielectric guide,
while the tangential components of the electric and magnetic fields are assumed to be contineous
across the two surfaces, perpendicular to the direction of propagation [12]. The basic modes in a
dielectric waveguide is TE or TM, but the TE mode is usually excited while the DRA is mounted
on the ground plane. By properly choosing the DRA dimensions, it can be ensured that unwanted
modes do not appear over the frequency band of operation. The rectangular DRA supports TEx,
TEy and TE
z modes, which are dependent on the dimensions of the DRA and the relationship
between w, d and b. If w > d > b, then fx < fy <fz , where fx is the resonant frequency of TEx
mode. Therefore a rectangular DRA will have a resonant frequency fmn on the TExδmn mode,
which can be solved by using the following transcedental equation [5], [10], [12], [13].
20
Fig.9 Geometry of rectangular DRA
( ⁄ ) √( )
Where,
And m and n are positive integers corresponding to the field variation within the y and z
direction respectively. The E and H fields within the DRA for the various modes can be
approximated by
2.3
( ) { ( )
( )} { ( )
( )}
21
( ) { ( )
( )} { ( )
( )}
( ) {
( )
( )} { ( )
( )}
( ) {
( )
( )} { ( )
( )}
( ) {
( )
( )} { ( )
( )}
Where the upper functions are chosen when the values of m and n are odd and the lower
functions when m or n are even [12], [13].
2.5 NOTCHED RECTANGULAR DRA:
A rectangular DRA with a central air gap is called notched rectangular DRA. By introducing a
central notch inside the DRA the bandwidth of the antenna can be increased. The increse in
bandwidth is based on by lowering the Q-factor. By introducing the central notch in DRA the
radiation Q-factor of the DRA can be reduced. By applying image theory, the notched DRA
appears similar to a square ring. By adjusting the dimension of the notch, a dual band or wide
band response can be achived. If the gap height is more, the coupling may be less, so to increase
the coupling, a high dielectric insert can be introduced. It acts as an impedance transformer
between the microstrip line and the DRA [12]. Fig.10 shows the design of a notched rectangular
DRA with a dielectric insert.
22
Fig.10 Notched rectangular DRA
23
2.6 CHAMFERED RECTANGULAR DRA:
A square DRA with four corners chamfered is used for generating circular polarization. It can
also be used to increase the band width of the antenna compared to the simple rectangular DRA.
Probe feeding is the best feeding technique for chamfered DRA. It decreases the radiation Q-
factor and increses the bandwidth of the antenna [12]. Fig.11 shows a rectangular DRA with one
chamfered face.
Fig.11 Chamfered rectangular DRA
24
CHAPTER-3: DRA ARRAY
25
3.1 DRA ARRAY THEORY:
Common antenna array elements include monopole, dipole, helixes, micro strip patches, printed
tapered slots and waveguide slot apertures. Each has their own strengths and weaknesses and are
generally selected to meet specific needs. Adding DRAs to the list of potential array elements,
we can get certain advantages for specific applications not available with other conventional
elements. DRAs are typically low gain antennas with broad radiation patterns, so they can be
arrayed to achieve higher gain or shaped radiation patterns like other conventional antennas [12],
[13], [27].
3.2 ARRAY THEORY:
The radiation pattern of an antenna of N-identical elements evaluated at a location ( ) in the
far field can be approximated by the product of the radiation intensity of the element and the
array factor using:
Radiation pattern =
20 ( )
Where,
Array factor = ∑
And,
Where;
= free space wave number
( ) = location of the nth element
= complex voltage excitation
26
The above equation for array factor is the general equation and applicable to arrays where the
elements are arbitrarily located and excited. For a linear array of N-elements where the elements
are uniformly spaced a distance d apart, the array factor simplifies to:
∑
In this case a uniform amplitude excitation (A1 = A2 = ….. = A0) is chosen in order to obtain
maximum directivity, and a linear phase progression ( ) is
selected to scan the beam to a desired angle. The array factor is further simplified to:
(
)
( )
Where;
d +
And,
(
)
3.3 FEED NETWORK FOR DRA ARRAY:
A feed distribution network is required to achieve the required amplitude and phase excitation
for each radiating element. Feed network design and its implementation is the most important
part of the array design. By properly designing the feed network junctions we can achieve the
desired amplitude excitation for each element. To get the desired power split at the junctions the
impedances of the transmission line must be designed properly. The phase excitation for the
array elements can be obtained by using passive phase delays within the feed network [12].
There are two types of feeding network used in DRA array. One is series feed and the
other one is parallel feed or corporate feed. These are the part of the constrained feed. The series
feed is a more compact network requiring less transmission line lengths and fewer junctions and
27
resulting in a lower insertion loss than parallel feed. However the series feed has less bandwidth
than parallel feed. The bandwidth of the end-fed series network is limited by the gain
degradation. Another factor limiting the bandwidth of this feed is the mismatch loss that occurs
due to the in-phase addition of the reflections from the various branches. For the parallel feed the
path length to each element is identical. The parallel or corporate feed has a relatively wide
bandwidth since it does not suffer from high mismatch losses. The corporate feed is much less
compact than the series feed. More losses are associated with corporate feed than series feed due
to the radiation from the discontinuities and longer line lengths [9], [12], [13], [27], [28]. Fig.12
shows the series and corporate feeds respectively.
Fig.12 (a) Series and (b) Corporate feed
Series feed
Corporate
feed
(a)
(b)
28
The most common method to provide the desired excitation to the DRA elements is to
use a microstrip feed network. If the elements are to be excited with equal amplitude and phase,
a corporate feed network is usually selected. Microstrip lines suffer from increased conductor
and surface wave losses at high frequencies. The parallel feed network although offering the
broader bandwidth, suffer from higher losses due to the longer path lengths. The parallel feeding
technique cannot be used in antennas where the physical spacing between the dielectric elements
is very small. In microstrip series feeding method, power is transferred from the lines to the
DRAs by electromagnetic coupling, which can be controlled by adjusting the spacing between
the DRA and the line. In case of series feed network the spacing between the dielectric
resonators is kept equal to the guided wavelength of the unloaded microstrip line in order to
avoid coupling [12], [27], [28], [29].
Another method to feed the DRA array is by using low loss dielectric image guide in
series feed technique. One disadvantage in microstrip feed is the losses due to conductor and
surface waves at high frequencies. This will not occur in dielectric image guide feed. The
dielectric material of dielectric constant is used as dielectric image guide line. The height and
width of the image guide line is taken as H and W respectively. The spacing between the DRAs
will be related to the guided wavelength of the dielectric image guide as similar to microstrip
feed line, and the separation between the DRAs and the dielectric image guide will control the
amount of coupling [12], [18], [29].
3.4 MUTUAL COUPLING:
In a transmitting array, power transmitted from each element will imping on the other elements
in the array or in a receiving array, some of the scattered power from each element will imping
upon nearby elements. The interaction between the elements of the array is referred to as mutual
coupling. It causes distortions in the radiation pattern of the array and can also affect the input
impedance of each element, resulting in mismatch losses. The type of antenna element used in
the array, its feed network and its design parameters like gain, radiation pattern etc. affect the
mutual coupling. The closer the dielectric elements placed in the antenna, the higher is the
mutual coupling. To get the amount of mutual coupling in an array, the mutual interaction
between two elements is often examined. The dielectric element spacing is kept normally from
29
0.5 to 1.0 to avoid mutual coupling in the antenna. The mutual coupling is mostly dependent
upon the shape of the DRA and the feed mechanism. The E plane coupling is stronger than H
plane coupling and it decreases less quickly with increasing element separation [12], [13], [29].
30
CHAPTER-4: NOTCHED
CHAMFERED RECTANGULAR
DRA
31
4.1 INTRODUCTION:
In this section a notched chamfered rectangular dielectric resonator antenna array design is
presented for wireless applications. Here the DRA array is excited by conformal patch connected
to microstrip line which is an effective feed mechanism and more efficient in energy coupling
[30], [31]. The central portion of the dielectric resonators of the DRA array is removed (notched)
and the four corners are chamfered to increase the bandwidth by lowering the Q-factor, and to get
the desired resonant frequencies. The antenna is simulated to analyze the performance of the
antenna array such as S-parameters, radiation patterns and realized gain. This proposed design
covers 2.4, 3.6 and 5 GHz WLAN bands and 3.4 to 3.7 GHz WIMAX bands limited by IEEE
802.11 and IEEE 802.16 standards, which overlap with each other. The design methodology of
this DRA array is discussed and the detail results of the proposed antenna are reported [32].
4.2 ANTENNA DESIGN:
The geometry of the rectangular DRA array has been shown in Fig.13, where rectangular shaped
two element dielectric resonators having dielectric constant 9.8, are placed over the substrate
having dielectric constant 4.4. The thickness of the substrate is 1.6 mm.
The dimension of the substrate is 58×56 mm2
(W×L). The dimension of the ground plane
is 58×27 mm2
(W×Lg). Partial ground plane is used to further enhance the bandwidth of the
DRA. The DRA array consists of two rectangular shaped dielectric resonators, where the
resonators having height hr = 13.5 mm and sides Lr = 17 mm. Fig.14 shows the geometry of the
proposed notched chamfered DRA array. The four corners of the rectangular resonator is
chamfered with Lc = 4 mm. The central portion of the resonators are removed i.e. rectangular
notches are introduced in the centers with side Ln = 7 mm. The chamfered and notched
techniques are used to enhance the performance of the antenna. Proper spacing between the two
resonators is maintained to avoid mutual coupling. The conformal strips are adopted as an
excitation mechanism which are attached on one side of the dielectric resonators and connected
to a microstrip feed line. The conformal strips has height hc = 13.45 mm and width Wc = 3 mm.
The microstrip feed line is etched on FR4 substrate with width Wf = 3 mm, Wf1 = 28 mm, and
length Lf = Lf1 = 14 mm which is connected by a SMA connector.
32
This design of the proposed DRA array is useful for multi-frequency operations [32],
[33]. The multi-frequency technique is another alternative way to overcome narrow band
limitations [34].
Fig.13 Perspective view of rectangular DRA
(a)
33
Fig.14 (a) Front view, (b) Perspective and (c) Rear view of the notched chamfered DRA array
(b)
(c)
34
4.3 RESULTS AND DISCUSSION:
The antenna is simulated using Microwave CST 2010 software and the simulation results are
shown in the following sections. By comparing the three designs i.e. a simple rectangular DRA,
a rectangular DRA with chamfered corners and a notched chamfered rectangular DRA, it can be
observed that the DRA array with notched chamfered resonators give better results and desired
resonant frequencies than the former two designs.
4.3.1 PARAMETRIC STUDY:
Parametric study is carried out by comparing different designs of the rectangular DRA array to
achieve good antenna performances. Fig.15 shows the simulated S-parameter for different
designs of rectangular DRAs. For the case of notched chamfered rectangular DRA array the
widest bandwidth from 2.18 to 3.75 GHz with good return loss is obtained.
1 2 3 4 5 6
-40
-35
-30
-25
-20
-15
-10
-5
0
lS1
1l (d
B)
Frequency (GHz)
Notched Chamfered DRA array
Chamfered DRA array
Rectangular DRA array
Fig.15 Comparison of S-parameter of different shapes of DRAs
35
A second frequency band from 4.84 to 5.14 GHz, covering the 5 GHz resonant frequency
is also observed only in case of notched chamfered DRA. Simulated result shows the DRA array
with the rectangular resonators having central notches and chamfered corners has a better
resonant frequency, S-parameters and bandwidth for dielectric resonator’s height hr = 13.5 mm
and conformal patch height hc = 13.45 mm.
Another parametric study is carried out by varying the ground plane’s dimension of the
antenna which is shown in Fig.16. By taking different heights of the ground plane i.e. Lg = 25, 27
and 29 mm, it has been observed that Lg = 27 mm gives multi-band characteristics and covers the
desired 2.4, 3.6 and 5 GHz resonant frequencies, while for other values of Lg the desired results
are not obtained.
1 2 3 4 5 6
-40
-35
-30
-25
-20
-15
-10
-5
0
lS1
1l (d
B)
Frequency (GHz)
Notched Chamfered DRA array
Chamfered DRA array
Rectangular DRA array
Fig.16 Comparison of S-parameter by taking different Lg values
36
4.3.2 GAIN CHARACTERESTICS:
Fig.17 plots the simulated gain versus frequency of the proposed DRA array, where the gain is
3.44 dB at 2.4 GHz, 5 dB at 3.6 GHz and 7.8 dB at 5 GHz. The gain of the DRA is improved by
using array method. The DRA also gives a VSWR value less than 2 over the entire frequency
range.
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
1
2
3
4
5
6
7
8
9
Ga
in (
dB
)
Frequency (GHz)
Lower Band (2.4GHz,3.6GHz)
Upper Band (5GHz)
Fig.17 Simulated Gain vs. Frequency curve for 2.4, 3.6 and 5 GHz
4.3.3 RADIATION PATTERN CHARACTERISTICS:
The simulated far field radiation patterns of the proposed two elements rectangular shaped DRA
array is shown in Fig.18. It shows the simulated radiation patterns at desired resonant frequencies
(2.4 GHz, 3.6 GHz & 5 GHz). It has been observed that the E plane radiation patterns are in
broadside direction and H plane are omnidirectional against frequency.
37
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
E-Plane
H-Plane
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
H-Plane
E-Plane
(a)
(b)
38
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
H-Plane
E-Plane
Fig.18 Simulated Radiation pattern of proposed DRA array at (a) 2.4 GHz (b) 3.6 GHz and (c) 5 GHz
4.4 CONCLUSION:
In this design, a chamfered rectangular shaped dielectric resonator antenna array with central
notch is presented for wireless applications. The proposed DRA array consists of two rectangles
of equal sides which are excited by conformal patch connected to microstrip line feed. The
simulated results show that the designed antenna covers bandwidth from 2.18 to 3.75 GHz and
4.84 to 5.14 GHz. The frequency band covers the desired frequencies i.e. 2.4 GHz, 3.6 GHz and
5 GHz, which covers several important application bands in current wireless communication
systems. The presented multi-band DRA array is suitable for WLAN and WIMAX applications.
(c)
39
CHAPTER-5: TWO ELEMENT
RDRA
40
5.1 INTRODUCTION:
In this section, design of a two element rectangular shaped dielectric resonator antenna (RDRA)
array is presented. The antenna covers the 2.4 GHz WLAN application limited by IEEE 802.11
standard. The RDRA array is excited by microstrip line coupling arranged in a corporate feed
technique. Simulation results are shown to analyze the performance of the designed antenna
array such as return loss, radiation patterns, gain and directivity. The design methodology is
discussed and the detail results of the proposed antenna are presented in this design. The
fabrication of the antenna is carried out and its measured reflection coefficient vs. frequency
curve is shown.
5.2 ANTENNA DESIGN:
Fig.19 shows the geometry of the DRA array. Teflon of dielectric constant 2.1 is used as dielectric
resonator (DR) for the DRA. The DR has been placed on the substrate having dielectric constant
4.4 with 1.6 mm of thickness. The dimension of the substrate is 70×60 mm2 (W×L). The rear
side of the substrate is covered with ground plane dimensioned as 70×30 mm2 (Wg×Lg). The
RDRA is having resonators of square cross section of dimension 19×19 mm2 (Wr×Lr) with
thickness Tr = 3 mm. The excitation mechanism adopts microstrip corporate feed arrangement.
50 Ω lines are used in the microstrip feed for impedance matching. The dimensions of the feed
line are W1 = 28 mm, W2 = 3 mm, L1 = 14 mm, L2 = 32 mm, L3 = 14 mm. Proper spacing is
maintained between the dielectric resonators to avoid mutual coupling. Fig.20 shows the front
and rear view of the fabricated antenna.
41
(a)
(b)
42
Fig.19 (a) Front (b) Perspective and (c) Rear view of the two element RDRA array
(c)
(a)
43
Fig.20 (a) Front view and (b) Rear view of the fabricated antenna
5.3 RESULTS AND DISCUSSIONS:
The given antenna is simulated using Microwave CST 2010 software and the simulation results are shown
in the following sections.
5.3.1 PARAMETRIC STUDY:
Fig.21 shows the simulated S-parameter for different feed length (L2) of the RDRA. By altering
the L2 value, the variation in resonant frequency can be observed. For the case of L2 = 32 mm the
desired resonant frequency at 2.4 GHz is achieved.
Another parametric study has been done by taking different height (Lg) of the ground
plane shown in Fig.22. By setting ground plane Lg = 30 mm the desired resonant frequency at
2.4 GHz occurred which is not possible at other Lg values.
(b)
44
1 2 3 4 5
-50
-40
-30
-20
-10
0
10
|S1
1| (d
B)
Frequency (GHz)
L2 = 30 mm
L2 = 32 mm
L2 = 34 mm
Fig.21 Comparison of S-parameters for different L2 values
1 2 3 4 5
-40
-30
-20
-10
0
|S1
1| (d
B)
Frequency (GHz)
Groung Lg = 28 mm
Ground Lg = 30 mm
Ground Lg = 32 mm
Fig.22 Comparison of S-parameters for different Lg values
45
Fig.23 shows the measured S-parameter result of the fabricated design taken by E5071C ENA Series
Network Analyzer.
Fig.23 Measures S-parameter of the fabricated antenna
5.3.2 GAIN CHARACTERISTICS:
Fig.24 plots the simulated gain versus frequency of the proposed DRA array. From the gain
characteristics it can be observe that the gain is 4.33 dB at 2.4 GHz.
46
2.0 2.5 3.0 3.5
3.0
3.5
4.0
4.5
Ga
in (
dB
)
Frequency (GHz)
Gain
Fig.24 Simulated Gain vs. Frequency curve
5.3.3 RADIATION PATTERN CHARACTERISTICS:
The simulated far field radiation patterns of the proposed two elements RDRA array is shown in
polar form. Fig.25 shows the simulated radiation pattern at 2.4 GHz. It has been observed that
the E plane radiation pattern is in broadside direction against frequency and the H plane radiation
pattern is omnidirectional.
47
-40
-20
0
0
30
60
90
120
150
180
210
240
270
300
330
-40
-20
0
E-Plane
H-Plane
Fig.25 Simulated Radiation pattern for 2.4 GHz
5.4 CONCLUSION:
In this design, a two element RDRA array is presented for 2.4 GHz wireless applications. The
proposed DRA array consists of two dielectric resonators of same sized rectangular cross section
which are excited by microstrip lines in corporate feeding technique. The simulated result shows
that the designed antenna covers the frequency range from 2.1 to 3 GHz which covers 2.4 GHz
WLAN band in current wireless communication systems.
48
CHAPTER-6: FOUR ELEMENT
RDRA ARRAY
49
6.1 INTRODUCTION:
Here the design of a four element rectangular shaped dielectric resonator antenna (RDRA) array
is presented for wireless applications. The RDRA array is fed by rectangular conformal patch
(RCP) connected to microstrip line [30], [31]. The antenna is simulated to analyze the
performance such as return loss, radiation patterns, gain and directivity. The RDRA array covers
the WLAN 4.9 GHz and 5 GHz bands limited by IEEE 802.11y and 802.11a/h/j/n family. It also
covers the WIMAX 5.8 GHz band of IEEE 802.16d family [11].The design methodology of this
DRA array is discussed and the detail results of the proposed antenna are presented in this
design. Parametric studies have been carried out by varying the RCP height and the ground plane
of the final design. The proposed antenna gives significant gain and better radiation pattern at the
resonant frequencies [36].
6.2 ANTENNA DESIGN:
Fig.26 shows the geometry of the four element RDRA array. Teflon of dielectric constant ( r )
2.1 is used as Dielectric Resonator (DR). The DR has been placed on the substrate having
dielectric constant ( 1r ) 4.4 with 1.6 mm of thickness. The dimension of the substrate is 90×50
mm2 (W×L). The rear side of the substrate is covered with ground plane dimensioned as 72×50
mm2 (Wg×Lg). The RDRA is having resonators of square cross section of dimension 11×11 mm
2
(Wr×Lr) with thickness Tr = 12 mm. The excitation mechanism adopts rectangular conformal
patch of size 8×7.5 mm2 (Wc×Lc) connected to microstrip corporate feed arrangement. 50 Ω lines
and 70.5 Ω lines are used in the microstrip feed line for impedance matching. The dimensions of
the feed line are W1 = W3 = W4 = 3 mm, W2 = W5 = 1.6 mm, L1 = 14 mm, L2 = 14.8 mm, L3 =
17.289 mm, L4 = 14 mm, L5 = 3.018, L6 = 3 mm and Lf = 2.15 mm. Proper spacing is maintained
between the dielectric resonators to avoid mutual coupling.
50
(a)
(b)
51
Fig.26 (a) Front view (b) Perspective view (c) Rear view of the four element RDRA array
6.3 RESULTS AND DISCUSSIONS:
The given four element DRA array is simulated using Microwave CST 2010 software and the simulation
results are shown in the following sections.
6.3.1 PARAMETRIC STUDY:
Fig.27 shows the simulated S-parameter for different RCP heights of the RDRA. By altering the
height of RCP, some variation in resonant frequency has been observed. For the case of Lc = 7.5
mm a total 3.1 GHz bandwidth (from 4 to 7.1 GHz) is obtained, whereas for the other values of
Lc the entire bandwidth is not achieved.
Another parametric study has been done by taking different width of the ground plane
shown in Fig.28. By setting different width of the ground plane the variation in the bandwidth
curve can be monitored. By setting ground plane Wg = 76 mm the widest bandwidth occurred but
with a notch in between the curve. With Wg = 68 mm a notch is coming in between the
bandwidth curve, but with 72 mm a whole bandwidth from 4 to 7.1 GHz is achieved.
(c)
52
3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
-50
-40
-30
-20
-10
0
S1
1 (
dB
)
Frequency (GHz)
RCP of Height 7.5 mm
RCP of Height 6.5 mm
RCP of Height 8.5 mm
Fig.27 Comparison of S-parameter for different RCP values
3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
-40
-30
-20
-10
0
S1
1 (
dB
)
Frequency(GHz)
Wg=72 mm
Wg=68 mm
Wg=76 mm
Fig.28 Comparison of S-parameter for different Wg values
53
6.3.2 GAIN AND DIRECTIVITY CHARACTERISTICS:
Fig.29 plots the simulated gain and directivity versus frequency of the proposed DRA array,
where the gain is 7.852 dB at 4.2 GHz, 9.083 dB at 5.2 GHz, 10.55 dB at 6.2 GHz and 9.568 dB
at 7 GHz. It also shows directivity of 7.898 dB at 4.2 GHZ, 9.109 dB at 5.2 GHz, 10.57 dB at 6.2
GHz and 9.783 dB at 7 GHz. From the plot it can be concluded that the given antenna shows
very good gain and directivity values.
3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
6
7
8
9
10
11
dB
Frequency(GHz)
Gain
Directivity
Fig.29 Gain and Directivity curves for the RDRA array
54
6.3.3 VSWR CHARACTERISTICS:
The simulated result of the proposed RDRA array is also showing a very good voltage standing
wave ratio (VSWR) over the entire frequency range. Fig.30 shows the simulated VSWR against
frequency. It has been remarkable that VSWR values are less than 2 over the entire bandwidth.
3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
VS
WR
Frequency(GHz)
VSWR
Fig.30 VSWR vs Frequency curve
6.3.4 RADIATION PATTERN CHARACTERISTICS:
The simulated far field radiation patterns of the proposed four elements RDRA array is shown in
Fig.31 in polar form. It shows the simulated radiation patterns at 4.2, 5.2, 6.2 and 7 GHz. It has
been observed that the E plane radiation patterns are in broadside direction against frequency and
the H plane radiation patterns are omnidirectional.
55
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
E-Plane at 4.2 GHz
H-Plane at 4.2 GHz
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
E field at 5.2 GHz
H field at 5.2 GHz
(a)
(b)
56
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
E-Plane at 6.2 GHz
H-Plane at 6.2 GHz
-30
-20
-10
0
10
0
30
60
90
120
150
180
210
240
270
300
330
-30
-20
-10
0
10
E-Plane at 7 GHz
H-Plane at 7 GHz
Fig.31 Radiation pattern of the RDRA Array at (a) 4.2 (b) 5.2 (c) 6.2 and (d) 7 GHz
(c)
(d)
57
6.4 CONCLUSION:
In this section a four element RDRA array is presented for wireless applications. The proposed
DRA array consists of four dielectric resonators of same sized rectangular cross section which
are excited by RCP fed connected to microstrip line in corporate feeding technique. The
simulated results show the designed antenna covers the frequency range from 4 to 7.1 GHz
which covers several important application bands in current wireless communication systems.
58
CHAPTER-7: CONCLUSION &
FUTURE WORK
59
7.1 CONCLUSION:
In the first section the WLAN and WIMAX bands and its applications are discussed. Different
shapes of Dielectric resonator antennas have been studied in this thesis. In the first part of the
thesis an introduction of DRA is given, and its characteristics, advantages, disadvantages and
applications are studied briefly. In this chapter the feeding methods used for DRAs are also
discussed. As in this thesis all the antenna designs are based on rectangular shape, a brief study is
done on the rectangular shapes of the DRA. In the next chapter the study of the DRA array is
given. The two types of feeding i.e. the parallel or corporate feed and the series feed is discussed.
The mutual coupling between the elements in a DRA array is also studied in this chapter.
In the fourth chapter a chamfered rectangular shaped dielectric resonator antenna array
with central notch is presented for wireless applications. The proposed DRA array consists of
two rectangles of equal sides which are excited by conformal patch connected to microstrip line
feed. The rectangular dielectric resonators further notched and chamfered to get better results.
The simulated results show the designed antenna covers the desired frequencies at 2.4 GHz, 3.6
GHz and 5 GHz, which covers several important application bands in current wireless
communication systems. It also shows gain values of 3.44 dB at 2.4 GHz, 5 dB at 3.6 GHz and
7.8 dB at 5 GHz. The presented multi-band DRA array is suitable for WLAN and WIMAX
applications.
In the second antenna design, a two element RDRA array for 2.4 GHz wireless
applications is presented in fifth chapter of this thesis. The proposed DRA array consists of two
dielectric resonators of same sized rectangular cross section which are excited by microstrip line
in corporate feeding technique. Here Teflon of dielectric constant 2.1 is used as dielectric
resonators. The simulated results show the designed antenna covers the frequency range from 2.1
to 3 GHz covering the 2.4 GHz WLAN band.
In the last design, a four element RDRA array for wireless applications is presented in
sixth chapter. The proposed DRA array consists of four dielectric resonators of same sized
rectangular cross-section which are excited by RCP fed connected to microstrip line in corporate
feeding technique. The simulated results show the designed antenna covers the frequency range
60
from 4 to 7.1 GHz which covers several important application bands in current wireless
communication systems. It also shows the gain values of 7.852 dB at 4.2 GHz, 9.083 dB at 5.2
GHz, 10.55 dB at 6.2 GHz and 9.568 dB at 7 GHz. The antenna covers the WLAN 4.9 GHz and
5 GHz bands limited by IEEE 802.11y and 802.11a/h/j/n family. It also covers the WIMAX 5.8
GHz band of IEEE 802.16d family.
7.2 FUTURE WORK:
Based on antenna designs, the following points were identified which would be helpful for
further investigation.
Fabrication and measurements of four element rectangular dielectric resonator antenna
array and the notched chamfered DRA array will be carried out in future.
Since the impedance bandwidth of Dielectric resonator antenna can be enhanced by using
multiple DRAs (stacked, embedded and DRA array), design of dielectric resonator
antenna arrays using embedded technique, will be carried out in future.
Besides, the experience of designing DRAs with microstrip line feeding with conformal
patch, Dielectric resonator antenna array with dielectric image guide feeding can further
be designed to minimize the metallic losses.
61
Publication
Imran Khan, Runa Kumari & S K Behera, “A Notched Chamfered Rectangular
Dielectric Resonator Antenna Array for Wireless Applications” IEEE
International Multi Conference on Automation, Computing, Control,
Communication and Compressed Sensing (iMac4s-2013), ISBN 978-1-4673-
5088-4 Feb 2013, Kerala.
Imran Khan, Runa Kumari & S K Behera, “A Four Element Rectangular
Dielectric Resonator Antenna Array For Wireless Applications” IEEE
International conference on Emerging Trends in Computing, Communication and
Nanotechnology (ICECCN-2013), ISBN 971-1-4673-5036-5, Feb 2013,
Tamilnadu.
62
References:
[1] D. Kajfej and P. Guillon, EDS., Dielectric Resonators. Norwood, MA; Artech House, 1986
[2] S.A. Long, M. W. McAllister and L.C. Shen, “The resonant cylindrical dielectric cavity
antenna,” IEEE Transactions on Antenna and Propagations, vol.31, pp. 406-412.1983.
[3] S.A. Long, M. W. McAllister and G. L. Conway, “Rectangular dielectric resonator antenna,”
IEEE Transactions on Antenna and Propagations, vol.31, pp. 406-412.1983.
[4] M. W. McAllister and S.A. Long, “Resonant hemispherical dielectric antenna,” IEEE
Transactions on Antenna and Propagations, vol.31, pp. 406-412.1983.
[5] Mongia, R. K., and P. Bhartia, “Dielectric resonator antennas – A review and general design
relations for resonant frequency and bandwidth,” International journal of microwave and
millimeter-wave computer-aided engineering, Vol. 4, No. 3, 1994, pp. 230-247.
[6] Petosa, A., et al., “Recent advances in dielectric resonator antenna technology,” IEEE
Antenna and Propagation Magazines, Vol. 40, June 1998, pp. 35-48.
[7] K.W. Leung, “Conformal Strip Excitation of Dielectric Resonator Antenna,” IEEE
Transactions on Antennas and Propagation, vol. 48, no. 6, pp. 961-967, Jun. 2000.
[8] M.S.M. Aras, M.K.A. Rahim, Z.Rasin and M.Z.A. Abdul Aziz, “An Array of Dielectric
Resonator Antenna for wireless application,” IEEE International RF and Microwave Conference
Proceedings, pp. 459.463, Dec 2008.
[9] W.M.A.Wahab, S.S. Naeini and D. Busuioc, ”Modeling and Design of Millimeter-Wave High
Q-Factor Parallel Feeding Scheme for Dielectric Resonator Antenna Arrays,” IEEE Antennas
and Wireless Propagation Letters, vol. 10, 2011.
[10] Y.M. Pan, K.W. Leung and Kai Lu,”Omnidirectional Linearly and Circularly Polarized
Rectangular Dielectric Resonator Antennas,” IEEE Transactions on Antennas and Propagation,
vol. 60, no. 2, Feb. 2012.
[11] Z. Abate, WiMAX RF Systems Engineering, Artech House Publishers, 2009.
[12] A. Petosa, Dielectric Resonator Antenna Handbook, Artech House Publishers, 2007.
[13] K. M. Luk and K.W. Leung, Dielectric Resonator Antennas, Hertfordshire, U.K.: Research
Studies Press Ltd., 2002.
[14] Kranenburg, R. A., and S. A. Long, “Microstrip Transmission Line Excitation of dielectric
resonator antennas,” IEEE Electronics Letters, Vol.24, No. 18, Sept. 1988, pp. 1,156-1,157.
63
[15] Mongia, R. K., A. Ittipiboon, and M. Cuhaci, “Experimental Investigations on Microstrip
fed Series Dielectric Resonator Antenna Array,” Symposium on Antenna Technology and
Applied Electromagnetics ANTEM 94, Ottawa, Canada, Aug. 1994, pp.81-84.
[16] G. P. junker, A. A. Kishk, A. W. Glisson, D. kajfez, “Effect of an air gap around the
coaxial probe exciting a cylindrical dielectric resonator antenna”, IEEE Electronics Letters, Vol.
30, No. 3, Feb. 1994, pp. 177-178.
[17] Junker, G. P., A. A. Kishk, and A. W. Glisson, “Input Impedance of Dielectric Resonator
Antennas Excited by a Coaxial Probe,” IEEE Transactions on Antennas & Propagation, Vol. 42,
No. 7, July 1994, pp. 960-966.
[18] Petosa, A., et al., “ Investigation of various Feed Structures For Linear Arrays of Dielectric
Resonator Antennas,” IEEE Antennas & Propagation Symposium Digest AP-S 1995, Newport
Beach, CA, pp. 1,982-1,985.
[19] Ittipiboon, A., et al., “Aperture Fed Rectangular and Triangular Dielectric Resonators for
Use as Magnetic Dipole Antennas,” IEEE Electronics Letters, Vol. 29, No. 23, Nov. 1993, pp.
2,001-2,002.
[20] Mongia, R. K., et al., “A Half-split Cylindrical Dielectric Resonator Antenna Using Slot
Coupling,” Microwave and Guided Wave Letters, Vol. 3, No. 2, Feb. 1993, pp. 38-39.
[21] Kishk, A. A. et al., “Slot Excitation of the Dielectric Disk Radiator,” IEEE Transactions on
Antennas & Propagation, Vol. 43, No.2, Feb. 1995, pp. 198-201.
[22] Pozar, D. M., and B. Kaufmann, “Increasing the Bandwidth of a Microstrip Antenna by
Proximity Coupling, “Electron. Lett., Vol. 23, 1987, pp. 368-369.
[23] Oltman, H. G., and D. A. Huebner, “Electromagnetically Coupled Microstrip Dipoles,”
IEEE Trans. On Antennas and Propagation, Vol. AP-29, 1981, pp. 151-157.
[24] Al Salameh, M. S., Y. M. M. Antar, and G. Seguin, “Coplanar-Waveguide-Fed Slot-
Coupled Rectangular Dielectric Resonator Antenna, “IEEE Transactions on Antennas &
Propagation, Vol. 50, No. 10, Oct. 2002, pp. 1,415-1,419.
[25] Wyville, M. A. Petosa, and J. S. Weight, “DIG Feed for DRA Arrays,” IEEE Antennas &
Propagation Symposium Digest AP-S 2005, Vol. 2b, pp. 176-179.
[26] A. Kishk, “Dielectric Resonator Antenna, a candidate for radar application”,Proc. Of the
2003 Radar Conference, pp. 258 – 264, May 2003.
[27] Runa kumari, Kapil Parmar and S K Behera, “A Dual Band Triangular shaped DRA array
for WLAN/WiMAX Applications,” Annual IEEE INDICON Conference, Hyderabad, India, Dec.
2011, pp. 1-4.
64
[28] G. Drossos, Z. Wu, and L. E. Davis, “Four-element planar arrays employing probe-fed
cylindrical dielectric resonator antennas,” Microw.Opt. Technol. Lett., vol. 18, no. 5, pp. 315–
319, 1998.
[29] D. Guha and Y. M. M. Antar, “Four-element cylindrical dielectric resonator array:
broadband low profile antenna for mobile communications,” presented at the Proc. XXVIIIth
General Assembly of the URSI,New Delhi, India, 2005.
[30] Liang X.-L., Denidni T.A and Zhang L. N, “Wideband L-Shaped dielectric resonator
antenna with a Conformal inverted-trapezoidal patch feed”, IEEE Trans. Antennas Propag., vol.
57, no. 1, Jan 2009,pp. 271-274.
[31] Lucia C. Y. Chu, Guha D. and Antar Y. M. M, “Conformal Strip-Fed Shaped Cylindrical
Dielectric Resonator: Improved Design of a Wideband Wireless Antenna”, IEEE Antennas
Wirel. Propag. Lett., vol. 8, 2009, pp 482-484.
[32] Imran Khan, Runa Kumari & S K Beher “A Notched Chamfered Rectangular Dielectric
Resonator Antenna Array for Wireless Applications” International Multi Conference on
Automation, Computing, Control, Communication and Compressed Sensing (iMac4s-2013),
ISBN 978-1-4673-5088-4 Feb 2013, Kerla.
[33] T. A. Denidni, Q. Rao, and A. R. Sebak, “Multi-eccentric ring slot-fed dielectric resonator
antennas for multi-frequency operations,” in IEEE Int. Symp. Antennas Propag., Jun. 2004, vol.
2, pp. 1379–1382.
[34] T. W. Li and J. S. Sun, “Dual-frequency dielectric resonator antenna with inverse T-shape
parasitic strip,” in IEEE Appl.v Comput. Electromagn. Soc. Int. Conf., Apr. 2005, pp. 384–387.
[35] Ching-Wei Ling, Chih-Yu Huang, “Dual-band circularly polarized dielectric resonator
antenna,” IEEE AP-S International Sym. Vol.2, pp 101, 2003.
[36] Imran Khan, Runa Kumari & S K Beher “A Four Element Rectangular Dielectric
Resonator Antenna Array For Wireless Applications” International conference on Emerging
Trends in Computing, Communication and Nanotechnology (ICECCN-2013), ISBN 971-1-4673-
5036-5, Feb 2013, Tamilnadu.