First Edition Magazine | 1
SEATING SYSTEMSD E S I G N E D , E N G I N E E R E D A N D M A N U FA C T U R E D B Y E L A N .
WWW.ELAN-INVENTA.COM
2 | Magazine First Edition1 | Seating systems Elan Inventa
ELAN SEATING SYSTEMS ARE DESIGNED, ENGINEERED AND MANUFACTURED TO COMPLEMENT THE ARCHITECTURE OF THE VENUE WHERE THEY ARE INSTALLED. THEY ARE MANUFACTURED TO THE HIGHEST REGULATIONS IN STANDARDS.
An important place among our reference projects is taken up by the 5,500-seat Zlatorog Sports Hall in Celje, Slovenia, equipped with Elan Inventa’s telescopic and fixed stands, handball goals and protection net-ting, all manufactured to the European standards applicable to the halls host-ing top sporting events. The hall has already hosted the 2004 European Handball Championship and Eurobas-ket 2013.
With its 6,500 seats, the Boris Trajkovski Sports Hall in Skopje, is the largest sports hall in Macedonia. It is equipped with telescopic stands, sports flooring, seats and other sports equipment.
For the Malmö Arena in Sweden Elan Inventa supplied telescopic stands with 2,500 seats. The Arena has a capacity of 12,000 for sporting events and up to 15,000 for concerts.
The Spaladium Hall in Split, Croa-tia, hosted the World Men’s Handball Championship in 2009. Elan Inventa delivered telescopic stands, dividing curtains, wooden sports floors, and other equipment. All the equipment in the hall is IHF and FIBA certified.
ELAN SEATING SYSTEMS
Multi-tiered seating systems are an essential part of all event venues (sports halls, stadiums, theatres, conference halls, lecture rooms, cinema thatres) as they provide spectators with high-quality, safe, and comfortable seating, as well as a good line of sight.Our seating systems can accommodate a wide range of seat options varying in model and type. In close consideration of the spatial and technical possibilities of each facility, Elan Inventa seating systems support the products of the world's leading seating manufacturers.
LEIPZIG GERMANY
ELAN INVENTA | Our success stories
First Edition Magazine | 3Elan Inventa Seating systems | 2
over 2,000 seating places.
Since spring 2013 Leipzig, Ger-many, boasts the most advanced telescopic seating system in Europe, called TransFlex. The stands, fully developed by Elan Inventa, feature complex technical solutions and meet the high requirements of the German market for quality, execution, and design.
TIMRA SWEDEN
The telescopic stands for the Stožice Arena, Ljubljana, Slovenia were one of Inventa’s biggest projects both in terms of complexity as well as scope and project deadlines. The company also provided other sports equipment for this venue, with most its products holding FIBA certificates. Stožice was the central venue of Euro-basket 2013.
Friends Arena in Sweden is one of the most modern football stadiums in the world. It complies with all the standards for the organization of the biggest sporting events. Elan supplied and fitted the stadium with unique outdoor grandstands, manufactured to the most demanding standards for outdoor use. Elan Inventa takes great pride in the design and installation of these 20-row telescopic stands with
CABINETTIP & ROLL
TELESCOPIC
DEMOUNTABLE
4 | Magazine First Edition3 | Seating systems Elan Inventa
ARENAConfigured to suit venue architecture and the custo-mers’ wishes. Arena telescopic stands feature corner system solu-tions, vomitories, standing places, press desks, partial opening/closing, and ventilation holes for enhanced air circulation. Fully tailored to the wishes of the investor and designer, with a wide range of accessories and extras.
MAXIMISE THE NUMBER OF SEATS, AND THE SPACE OCCUPIED BY THE STAND CAN BE USED WHEN THE STAND IS CLOSED EITHER MANUALLY OR BY MEANS OF AN ELECTRIC DRIVE.
TELESCOPIC STANDSTHE USEFUL SURFACE AREA INCREASES CON-SIDERABLY WHEN THE STANDS ARE CLOSED.
Available in a variety of positions and attachment types: against a wall, under a balcony, self-standing. Conform to the following regulations in standards:
EN 13200, which specifies design and management requirements for spectator facilities at permanent and temporary venues including sport stadia, sport halls, and other indoor and outdoor facilities;ISO 3834, which applies to controlled manufacture of metal structures;ISO 14001, which specifies environmental manage-ment requirements; and ISO 9001 for quality assurance in design, develop-ment, production, supply, installation and servicing.
BASICThe simplest telescopic stand unit. The length of the block is 5 or 6 m, row depth 75 or 80 cm and riser 38 cm.Seating is attached to the front end of the row. Types of installation: against a wall, under a balcony.
PROTakes the classical telescopic stand a step further, featuring a range of accessories and a variety of types best suited to the available space.Available accessories: electric drive, front and rear guardrails, a variety of side covers,and a wide range of seating options.Types of installation and attachment: against a wall, under a balcony.
PLANINA PRI SEVNICI SLOVENIA HOČE SLOVENIA
ARENA STOŽ ICE LJUBLJANA, SLOVENIA
First Edition Magazine | 5Elan Inventa Seating systems | 4
FULLY DEVELOPED BY ELAN, TRANSFLEX TELESCOPIC STANDS FEATURE COMPLEX TECHNICAL SOLUTIONS AND MEET THE HIGH REQUIREMENTS OF THE GERMAN MARKET FOR QUALITY, EXECUTION, AND DESIGN.
TRANSFLEXSelf-standing telescopic stands need no floor or wall attachment.In addition to easy storage, the bleachers are trans-portable.A seating block can be divided into two separate units.Fitted with an internal staircase accessed from the rear.Optional indoor bleachers with a telescopic staircase.
TEATROTelescopic seating for theatres, conference halls, cinemas, lecture rooms with 75 to 95 cm row depth for enhanced comfort.All ends and contacts are rubber-capped to reduce noise.Available solutions include corner and concave sys-tems and feature ventilation holes, PVC or textile-co-vered platforms, and aisle lighting.A wide range of upholstered seats with armrests and/or desks; diverse railing options.
LJUBLJANA WALDORF SCHOOL LJUBLJANA, SLOVENIA
LEIPZIG GERMANY
6 | Magazine First Edition5 | Seating systems Elan Inventa
MINI BLEACHERS PROVIDE SEATING UP TO THREE ROWS. CAN BE ATTACHED TO A WALL OR TRANSPORTABLE, WITH AN INNOVATIVE STORAGE SYSTEM.
CABINET AND TIP&ROLL BLEACHERS
CABINETDesigned, engineered and manufactured as an ideal solution for small-size spectator facilities when available space prevents installation of larger stands. Modules, 2 m in length, can be placed next to each other. Each module seats at least 12 persons.A closed cabinet bleacher can be finished with an acoustic panel or soft wall padding into an attractive wall panel, with no sharp edges, which adds to the safety of the venue. Easy to handle.
TIP&ROLLFree-standing metal structure with integrated casters and an innovative storage system.Intended for use in closed spaces (e.g. school gyms, classrooms, multi-purpose rooms). The bleacher is composed of 5 different wheeled mo-dules of a total length 8.5 m.Designed, engineered and manufactured to ensure simple handling and economical storage.A bleacher set is composed of 5 bleacher units of different sizes (four seating blocks and a staircase) providing a seating area for 50 people.
VOJNIK SLOVENIA
SLOVENSKA BISTRICA SLOVENIA
First Edition Magazine | 7Elan Inventa Seating systems | 6
DEMOUNTABLE STANDS ARE FREE-STANDING METAL STANDS OF RATIONAL STRUCTURE, WHICH CAN BE ASSEMBLED OR DISASSEMBLED IN A VERY SHORT TIME.
DEMOUNTABLE STANDS
Intended for use in outdoor sports venues and games areas as well as indoor sports facilities, event venues, theatres, etc.Can be expanded to suit increased needs.The stand is manufactured to the requirements of SIST EN 13200-1, 2, 6, EN 191-1-1 Eurocode 1, EN 1991-1-4 Eurocode 1. Fully coated with anti-corrosion protection, the stand is suitable for outdoor and indoor use.Fitted with an innovative system for fast and simple as-sembly and disassembly.Seats are ergonomic, with our without backrest, surface treated with UV protection, and tested to EN 12727:01. UV protection, tested by the Slovenian National Civil and Engineering Institute in Ljubljana.BONIFIKA KOPER, SLOVENIA
LESCE SLOVENIAWORLD ROWING CHAMPIONSHIP BLED, SLOVENIA
8 | Magazine First Edition7 | Seating systems Elan Inventa
OUR SEATING SYSTEMS CAN ACCOMMODATE A WIDE RANGE OF SEAT OPTIONS VARYING IN MATERIAL, MODEL AND TYPE. IN CLOSE CONSIDERATION OF THE TECHNICAL POSSIBILITIES OF THE SITE, ELAN INVENTA SEATING SYSTEMS SUPPORT THE PRODUCTS OF THE WORLD'S LEADING SEATING MANUFACTURERS.
OUR SEATING SYSTEMS INCLUDE A VARIETY OF SEAT TYPES AND VARIOUS COLOURS FOR ARCHITECT'S SELECTION. ALL SEATS SUPPLIED BY THE MANUFACTURER ARE STABLE AND SAFE, COMPLYING TO HIGH MATERIAL STANDARDS.
WWW.ELAN-INVENTA.COM
Elan Inventa Seating systems | 8
SE
ATIN
G S
YS
TEM
S
FOR
ALL
EV
EN
T V
EN
UE
S
10 | Magazine First Edition
Telescopic stands Fixed stands
front mount rear mount to platform
Bracket mount (vertical element)
Bracket mount (horizontal element)
9 | Seating systems Elan Inventa
First Edition Magazine | 11Elan Inventa Zgodba o športu | 1
COMPACTSTANDARD BENCH page 11
ERGO BENCH page 12
DAPLAST G3 page 13
DAPLAST A2 page 14
ESSENTIALTABO page 15
DAPLAST A3 page 16
AUBA page 17
GOAL page 18
DAPLAST AB page 19
DAPLAST CR2 page 20
DAPLAST CR3 page 21
DAPLAST CR4 page 22
DAPLAST CR5 page 23
DAPLAST CRM page 24
STATEMENTBOX 901 page 26
BOX 903 page 27
BOX 908 page 28
DAPLAST AVATAR page 29
SE
ATIN
G
SY
STE
MS
WWW.ELAN-INVENTA.COM
Elan Inventa Seating systems | 10
12 | Magazine First Edition
COMPACTSTANDARD BENCH
Standard bench is a flexible and elegant seating solu-tion for closed spaces.Suitable for use in fixed and telescopic stands. Available in beech plywood, MDF, or laminated chip-board.
CHARACTERISTICS
Thickness 18 mm, all visible edges rounded to a 5 mm radius.Fixed to the understructure with hot-zinc coated screw clamps.Height of seating from 42 to 48 cm.Width of seating from 28 to 30 cm.Used in stands with row rise of 30 to 45 cm.Used in stands with row depth of 75 to 90 cm.Surface treated with DIN 4102 B1 flame retardant lacquer.Conforms to EN 13200-3 and EN 913.
OPTIONS
Available in beech plywood, MDF, or laminated chipboard.Can be used in telescopic or fixed stands.Upholstered seating surface.Bench and upholstery fabric colour selection.Optional foldable backrest.
11 | Seating systems Elan Inventa
STANDARD BENCHERGO BENCHDAPLAST G3DAPLAST A2
28 - 30 cm
42 -
48
cm
100 - 200 cm
min
6 c
m
First Edition Magazine | 13Elan Inventa Seating systems | 12
ERGO BENCHStandard bench upgraded with an ergonomic seat-ing surface, without compromising on flexibility and elegance.Excellent seating solution for limited-space venues.
CHARACTERISTICS
Manufactured from beech plywood, thickness 10 mm.Laminated and fixed to the stand structure with hot-zinc coated screw clamps.Surface treated with DIN 4102 B1 flame retardant lacquer.Conforms to EN 13200-3 and EN 913. Height of seating from 42 to 48 cm.Width of seating from 28 to 30 cm.Used in stands with row rise of 30 to 42 cm.Used in stands with row depth of 75 to 90 cm.
OPTIONS
Attachment to the floor or stand (fixed or telescopic).Available in a range of bench colours.
42 -
48
cm
min
6 c
m
100 cm
28 - 30 cm
14 | Magazine First Edition
DAPLAST G3A bench-style seat consisting of two parts – seats and connection bridges – to form benches of any length.For fixed and telescopic stands.
CHARACTERISTICS
Seat moulded by injection in stabilised high-quality polymers.Light resistance (anti-UV, EN 13200-4).Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Multiple central drainage.Frame retardant (M4 to M2 class).Two anchoring points, reinforced attachment to the base.Used in stands with row depth of 75 cm to 90 cm.
OPTIONS
Mounted directly on a riser or tread, or to the stand structure (fixed or telescopic).Seats available in a range of colours, and in any colour techni-cally available for orders of over 2500 units.Numbering at the sides of connecting bridges.
13 | Seating systems Elan Inventa
Standard colours:
Special colours:
45 / 50 cm
45 / 95 mm
45 mm
First Edition Magazine | 15Elan Inventa Seating systems | 14
DAPLAST A2A simple seating solution for all types of venues, in-cluding high-volume venues.Excellent resistance to wear and load. Sealed around the entire perimeter to prevent dirt from accumulating inside the seats, and for easy cleaning.
CHARACTERISTICS
Seat moulded by injection in stabilised high-quality polymers.Light resistance (anti-UV, EN 13200-4).Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Central drainage system.Frame retardant (M4 to M2 class).Single anchoring point, reinforced attachment to the base.Used in stands with row depth of 75 to 90 cm.
Standard colours:
Special colours:
OPTIONS
Mounted directly on a riser or tread, or to the stand structure (fixed or telescopic).Seats available in a range of colours.Manufactured in any colour technically available for orders of over 2500 units.Numbering in the upper part of the backrest.
16 | Magazine First Edition
TABODAPLAST A3AUBAGOALDAPLAST ABDAPLAST CR2DAPLAST CR3DAPLAST CR4DAPLAST CR5DAPLAST CRM
ESSENTIALTABO
Multipurpose wooden seat made of durable plywood, intended for medium and large-sized indoor venues.Fixed or tip-up seat.Mounted on a central leg or directly to the stand.
CHARACTERISTICS
Folding wooden seat.Tip-up backrest attached to metallic brackets.Seat and backrest plywood thickness 10 mm.Surface treated with DIN 4102 B1 flame retardant lacquer.Conforms to EN 13200-3 and EN 913.Axial seat spacing 46 to 50 cm.Seats are connected for tier folding.Used in stands with row rise from 28 to 40 cm.Minimum row depth 80 cm.
15 | Seating systems Elan Inventa
45 - 50 cm 42 - 46 cm
42 -
48
cm
50 c
m
18 c
m
12 cm
OPTIONS
Suitable for installation in fixed or telescopic stands.Seats with support leg can be attached to any surface type.Mounted to the front or rear of telescopic stand platform.Upholstered with durable, flame-retardant fabric (minimum 80,000 double rubs).Available in a range of seat and upholstery fabric colours.Upholstered in accordance with EN 1021-1 (ignitability of materi-als).
First Edition Magazine | 17Elan Inventa Seating systems | 16
DAPLAST A3Top-range solution for seating systems in high-volume venues.Excellent resistance to wear and load.Sealed around the entire perimeter to prevent dirt from accumulating inside the seats, and for easy cleaning.
CHARACTERISTICS
Double-wall backrest.Ergonomic backrest 35 cm in height, with lumbar support.Conforms to UEFA and FIFA recommendations.Central drainage system.Light resistance (anti-UV, EN 13200-4).Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Two anchoring points; reinforced attachment to the base.
Standard colours:
Special colours:
OPTIONS
Mounted directly on a riser or tread, or to the stand structure at any height.Available in a range of standard seat and upholstery fabric colours, or in any technically available colour for orders above 2500 units.Numbering plates in the upper part of the backrest.
18 | Magazine First Edition17 | Seating systems Elan Inventa
AUBAA durable, multipurpose seat with a reliable automatic up-down mechanism.Available in fixed or tip-up seat option.Can be mounted directly on the stand.
CHARACTERISTICS
Folding wooden seat.Automatic flip-up seat surface attached to metallic brackets.Plywood thickness 10 mm.Surface treated with DIN 4102 B1 flame retardant lacquer.Conforms to EN 13200-3 and EN 913.Axial seat spacing from 46 to 50 cm.Opens and folds automatically.Front attachment to the telescopic stand platform.
45 - 50 cm
44 cm
42 -
48
cm
47 cm
42 cm
40 -
46
cm
6 -
12 c
m11
- 1
6 cm
OPTIONS
Suitable for use in telescopic or fixed stands.Upholstery fabric rated at minimum 30,000 double rubs.Available in a variety of seat and upholstery colours.Available as a tip-up seat.Optional fixed backrest.
First Edition Magazine | 19Elan Inventa Seating systems | 18
GOALHeavy duty, multipurpose leg-supported seat.Available in a fold-down option.Suitable for medium- and large-sized indoor venues.Can be mounted on a central leg support.
CHARACTERISTICS
Folding wooden seat on a support leg.Automatic flip-up seat surface attached to metallic brackets.Plywood thickness 10 mm.Width of seating from 42 to 47 cm.Surface treated with DIN 4102 B1 flame retardant lacquer.Conforms to EN 13200-3 and EN 913.Axial seat spacing from 50 to 55 cm.Linked together for easier fold-down.Upholstery fabric rated at minimum 80,000 double rubs, EN 1021-1 compliant.Used in stands with row depth of 75 to 90 cm.
OPTIONS
Available in a range of seat and upholstery fabric colours.Backrest can be custom embroidered with the client’s logo.Numbering plates on the backrest.
23 cm
50 - 55 cm 42 - 47 cm
82 -
88
cm
42 -
48
cm
20 | Magazine First Edition19 | Seating systems Elan Inventa
DAPLAST ABFoldable multipurpose seat ideal for sports and other venues.Fitted with a counterweight mechanism for automatic lifting.Can be mounted on a riser or floor, support leg, or stand structure.
CHARACTERISTICS
Seat and backrest from smooth material that prevents accumula-tion of dirt.Fitted with a weight-loaded mechanism for automatic fold-up.Reinforced seat folds made by injecting a fibreglass-reinforced polymer substance.Load-bearing structure made of cold-laminated S275 steel and hot galvanized or cataphoretic coating. Light resistance (anti-UV additive, EN 13200:4)Resistance to severe public use (vandalism) (EN 12727:01 – certi-fied by Aidima).Flame retardant (M4 to M2 norm).
Standard colours:
Special colours:
OPTIONS
Spring-loaded fold-up mechanism.Oven-painted frame.Mounted on a riser or floor, or stand structure.Available in a range of seat and upholstery fabric co-lours, or in any technically available colour for orders above 2500 units. Numbering plates.Armrests attached to backrests.Upholstered seat and backrest, optional embroidery.Optional writing pad.
First Edition Magazine | 21
DAPLAST CR2A heavy–duty seat with mid-height backrest for con-ventional grandstands and multipurpose venues.Sealed around the entire perimeter to prevent dirt from accumulating inside the seats, and for easy cleaning.
CHARACTERISTICS
Seat moulded by injection of stabilized high-quality polymers.Light resistance (anti-UV additive, EN 13200:4)Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Central drainage.Flame retardant (M4 to M2 class).One central anchoring point reinforced with a small steel plate.Standard colours:
Special colours:
Elan Inventa Seating systems | 20
OPTIONS
Mounted directly on a riser or tread, or to the stand structure at any height. Available in a range of seat and upholstery fabric colours, or in any technically available colour for orders above 2500 units.Numbering plates in the upper part of the backrest.Attachment can be upgraded by two or three anchoring points anchored at the seat base.Armrests (individual or collective).
22 | Magazine First Edition
DAPLAST CR3High-backrest heavy-duty seat ideal for conventional grandstands. Sealed around the entire perimeter to prevent dirt from accumulating inside the seats, and for easy cleaning.
CHARACTERISTICS
Seat moulded by injection of stabilized high-quality polymers.Light resistance (anti-UV additive, EN 13200:4)Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Central drainage.Flame retardant (M4 to M2 class).Two anchoring points, reinforced attachment at the seat base.Manufactured in line with UEFA and FIFA recommendations.
21 | Seating systems Elan Inventa
Standard colours:
Special colours:
OPTIONS
Mounted directly on a riser or tread, or to the stand structure at any height.Available in a range of seat and upholstery fabric colours, or in any technically available colour for orders above 2500 units.Numbering plates in the upper part of the backrest.Armrests (individual or collective).
First Edition Magazine | 23Elan Inventa Seating systems | 22
DAPLAST CR4High-backrest heavy-duty seat suitable for all types of grandstands. Sealed around the entire perimeter to prevent dirt from accumulating inside the seats, and for easy cleaning.
CHARACTERISTICS
Seat moulded by injection of stabilized high-quality polymers.Light resistance (anti-UV additive, EN 13200:4)Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Central drainage.Flame retardant (M4 to M2 class).One central anchoring point at the base, reinforced with a steel plate.Manufactured in line with UEFA and FIFA recommendation.
Standard colours:
Special colours:
OPTIONS
Mounted directly on a riser or tread, or to the stand structure at any height (metal or plexiglass).Available in a range of seat and upholstery fabric co-lours, or in any technically available colour for orders above 2500 units.Numbering plates in the upper part of the backrest.Armrests (individual or collective).Upholstered seat and backrest with optional engrav-ing.Backrest can be custom embroidered with logo.
24 | Magazine First Edition
DAPLAST CR5Monoblock seat with high backrest, ideal for first-class sports venues. Specially designed for narrow tread venues requiring backrest seats.Aesthetically pleasing with modern design.
CHARACTERISTICS
Seat moulded by injection of stabilized high-quality polymers.Light resistance (anti-UV additive, EN 13200:4)Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Central drainage.Flame retardant (M4 to M2 class).One central anchoring point, reinforced with a steel plate.
23 | Seating systems Elan Inventa
Standard colours:
Special colours:
OPTIONS
Backrest can be custom embroidered with the cli-ent’s logo (metal or plexiglass).Available in a range of seat and upholstery fabric co-lours, or in any technically available colour for orders above 2500 units.Numbering plates in the upper part of the backrest.Armrests (individual or collective).Attachment can be upgraded by two or three an-choring points anchored at the seat base.
First Edition Magazine | 25Elan Inventa Seating systems | 24
DAPLAST CRMHigh-backrest heavy-duty seat suitable for large sports arenas and narrow-tread grandstands. Aesthetically pleasing with modern design.
CHARACTERISTICS
Seat moulded by gas-assisted injection of stabilized high-quality poly-mers.Light resistance (anti-UV additive, EN 13200:4)Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Backrest with tubular air chambers, with no reinforcement nerves vis-ible at the back, provides all the benefits of a double-back seat. Central drainage system.Flame retardant (M4 to M2 class).One central anchoring point, reinforced with a steel plate.Manufactured in line with UEFA and FIFA recommendations.
Standard colours:
Special colours:
OPTIONS
Mounted directly on a riser or tread, or to the stand structure at any height (metal or plexiglass).Available in a range of seat and upholstery fabric co-lours, or in any technically available colour for orders above 2500 units.Numbering plates in the upper part of the backrest.Armrests (individual or collective).Attachment can be upgraded by two or three an-choring points anchored at the seat base.
26 | Magazine First Edition25 | Seating systems Elan Inventa
First Edition Magazine | 27
STATEMENT
Elan Inventa Seating systems | 26
BOX901Compact design and ergonomic form for long service life and low installation and maintenance costs.
CHARACTERISTICS
Seat and back come with a 5-year UV resistance colour certifi-cate.Components moulded using recognised quality polymers.All materials are UV & FR rated as required. Compact seat width for high volume installation.Strength and durability tested.TBS rail available in galvanised and powder-coated finish.Various installation options (riser mount, tread mount).Soft-action for tip-up mechanism.
BOX 901BOX 903BOX 908DAPLAST AVATAR
OPTIONS
Also available in upholstered version.Cupholders.Armrests.Choice of plastic and upholstery fabric colours.
28 | Magazine First Edition27 | Seating systems Elan Inventa
BOX 903Due to its compact form, Model 903 is particularly suited for high volume installations.A raised seat takes up very little space and enables the flow of spectators.
CHARACTERISTICS
Seat and back come with a 5-year UV resistance colour certifi-cate.Components moulded using recognised quality polymers.All materials are UV & FR rated as required. Compact seat width for high volume installation.Strength and durability tested.TBS rail available in galvanised and powder-coated finish.Lens-protected numbering system.Various installation options (riser mount, tread mount).Soft-action for tip-up mechanism.
OPTIONS
Cupholders.Armrests.Plastic colour selection.
First Edition Magazine | 29Elan Inventa Seating systems | 28
BOX908The BOX Seat 908 is the ideal solution for superior seated comfort.Integrates the cushion into the seat, and protects seat edges from wear.Designed to incorporate all aspects of comfort.
CHARACTERISTICS
Upholstered mid–height seat.Exclusive maintenance-free materials.All components are moulded using recognised quality poly-mers.All materials are UV & FR rated as required. Compact seat width for high volume installation.Strength and durability tested.TBS rail available in galvanised and powder-coated finish.Various installation options (riser mount, tread mount).Soft-action tip-up mechanism.
OPTIONS
Cupholders.Padded armrest.Plastic colour selection.
30 | Magazine First Edition29 | Seating systems Elan Inventa
DAPLAST AVATARModern tip-up seat for the most-demanding venues.Rail mounted to accommodate any desired spacing be-tween seats.Compact fold-up form optimises the available distance between seats.
CHARACTERISTICS
Seat and back made from smooth material to prevent dirt from accumulating.Seat made from high-quality polyamide reinforced with high-resistance fibreglass.Mounted on top-quality steel rails and hot galvanised or epoxy coating.Light resistance (anti-UV, EN 13200-4).Resistance to severe public use (vandalism) (EN 12727:01 – certified by Aidima).Central drainage system.Frame retardant (M4 to M2 norm).Manufactured in line with UEFA and FIFA recommendations.
OPTIONS
Can be mounted onto the floor or the stand structure.Seats available in a range of colours, and in any colour tech-nically available for orders of over 2500 units.Shock absorbers incorporated in the tip-up mechanisms.Padding.Armrest.
45 - 50 cm44,5 cm
19 cm
42 -
45
cm
Standard colours:
Special colours:
First Edition Magazine | 31Elan Inventa Seating systems | 30
32 | Magazine First Edition
ELAN INVENTA D.O.O.Begunje na Gorenjskem 14275 Begunje na GorenjskemSlovenia
Tel +386 4 53 51 333Fax +386 4 53 51 107Email [email protected]
www.elan-inventa.comwww.elan-seatingsystems.eu
Copyright © 2014 Elan Inventa
WWW.ELAN-INVENTA.COM