Destroy DR partition that is no longer neededSign on to HMC1.1 sign on to hmc from browser enter https://10.42.121.36/preloginmonitor/

1.2 userid = hscroot pass word = Aktion1 use classic interface press sign in

1.3 click on servers in left column

1.4 Click on the Server-8286-41A-SN782C6DX

Turn off the Partition2.1 Place a check mark in front of the partition that is no longer needed. Hover at end of server name and a small popup appears

2.2 click on operations and then shutdown

2.3 Select immediate then click ok

2.4 Click yes on the warning Screen

Delete the Partition3.1 Place a check mark in front of the partition that is no longer needed. Hover at end of server name and a small popup appears.

3.2 Select Operations then Delete

3.3 Check delete assosiated virtual disk. Press OK

3.4 place a check mark in front of all the disk. Press ok

Verify delete

4.1 Partition should not show in the list any more. Remove all check marks at bottom expand configuration and then virtual resources then click on Virtual Storage Management

4.2 Click the Query Button

4.3 verify that all the Disk for that partition have been deleted

Create a new base system1.0 Connect and Gather information1.1 sign on to hmc from browser enter https://10.42.121.36/preloginmonitor/

1.2 userid = hscroot pass word = Aktion1 use classic interface press sign in

1.3 click on servers in left column

1.4 Click on the Server-8286-41A-SN782C6DX

1.5 Make note of all the other Partitions

VIOs01 will always be 1 You may have 0 – 1 or 2 IBM I Partitions If there are, 2 you need to determine which one needs to be deleted see previous sections If there are, 0 Write down 10 for SCSI Port

If there is 1

1.5a Click on VIOs01 then the Virtual Adapters Tab. Write down the SCSI adapter that is not assigned in this case it is 15.

Create partition1.6 Go back to the servers screen. Put a check mark in front of the server. Hover at end of server name and a small popup appears

1.7 select configuration then create partition then IBM i

1.8 The “Create Lpar Wizard” opens. The “Create Partition” step is displayed. Enter a partition name. (Suggested DR-YYMMDD) using todays date. Click Next.

1.9 The “Partition Profile” step is displayed. Add a p to the end of the partion name then click next.

1.10 The “Processors” step is displayed. Click shared the click next.

1.11 The “Processing settings” step is displayed. Minimum processing unit =.05; Desired = .3; Maximum = 1; let other values default - click next.

1.12 The “Memory Settings” step is displayed. Minimum = 4; desired = 16 maximum = 32- click next

1.13 The “I/O” step is displayed. Just click next

1.14a The “Virtual Adaptors” step is displayed. Click Actions

Change the Maximum virtual adaptors to 100

1.14b Then Click Actions; Create virtual Adapter Then Ethernet Adapter

1.14c set Adaptor Id = 2 Vswitch = ETHERNET0(Default) – Click OK

1.14d Click Actions - Then Click Create virtual Adapter - Then SCSI Adapter

1.14e Set values for the SCSI port

Adaptor number is the value you wrote down at step 1.5a (In this case it is 15) Type of adptor is Client Server partion is VIOs01(1) Server adapter id is the same as the client adptor id

1.15 The “OptiConnect Settings” step is displayed. Click next

1.16 The “Tagged I/O” step is displayed. Set vales then click next

Set Load source = Client SCSI Slot xx

Alternate restart device = Client SCSI Slot xx Console = Management Console

1.17 The “Optional Settings” step is displayed. Click Next

1.18 The “Profile Summary” step is displayed. Click Finish

Click Next and the partition will be created

The new Partition should now show in the list.

2.0 Add disk2.1 Remove all check marks. At bottom expand configuration and then virtual resources then click on Virtual Storage Management

2.2 Click on Virtual Storage Management. The following screen is displayed. Click on Query

2.3 Click on Create Virtual disk

2.4 Click on Create Virtual disk; enter values; click ok

Virtual disk name – partionname-xx Storage pool name = San-Base Virtual disk size = 100 GB ( first 3 for os) you can use 300 GB later Assigned partition = Select the partition you just completed.

2.4a Repeat till Desired disk have been created and assigned

2.4b Review change as need when finish Click Close

3.0 create iAccess client solution Session3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

3.10

4.0 IPL d the partition

___________________ New Changes starting here (frank /12/2018)__________

5.0 Installing IBMi License internal Code

https://www.ibm.com/support/knowledgecenter/en/ssw_ibm_i_72/rzahc/sc415120.pdf?view=kc

Chaper 12 pdf page 108 – step 8

If Prompted for a userid and password use 11111111 for both

You should be able to skip step 11

On step 12 select the fist drive as the load source

Step 14 enter 2

Follow 15 -20

Skip step 1 – 7

Do step 8 skipping f

But the b_group_1 CD in

6.0 OS installStaring with step 10 ( device type is optical)

Continue on (You will not do 15b) all the way through step 30

7.0 Copy OS dvds to Image catalog*

8.0 TCP settings9.0 Copy ptfs to image catalog10.0 Install remaining Lic PGM12.0 Install group ptfs13.0 IPL14.0 Test15.0 Power off till needed