Dial-up Networking Setup Guide 7.20 Mar14

Installation Guide

Dial-Up Networking Setup

Version 7.2

2 Dia l -Up Networking Setup Gu id e

2014 Anite Finland Ltd. All rights reserved.

This manual, as well as the software described in it, is furnished under license and may only be used or copied in accordance with the terms of such license. The information in this manual is intended for informational use only and is subject to change without notice. Anite Finland Ltd assumes no responsibility or liability for any errors or inaccuracies that may appear in this user manual.

Except as permitted by such license, no part of this publication may be reproduced or transmitted in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Anite Finland Ltd.

Windows XP, Windows 7, Windows 8, Outlook, and Internet Explorer are registered trademarks of the Microsoft Corporation in the United States and other countries. MapInfo and MapX are registered trademarks of MapInfo Corporation. CDMA 2000 is a registered trademark of the Telecommunications Industry Association (TIA -USA). The license management portion of this Licensed Technology is based on SentinelLM* 1989-2003 Rainbow Technologies, Inc. Sentinel is a registered* trademark of SafeNet, Inc. All rights reserved.

POLQA is a registered trademark of OPTICOM GmbH. Used by permission. 2011 by the POLQA Coalition of OPTICOM GmbH, Germany - SwissQual AG, Switzerland - KPN, The Netherlands - TNO, The Netherlands.

Printed in Finland

Revision 7.20.03, Last edited March 2014.

CONTE NTS 3

CONTENTS

INTRODUCTION 6 DEVICE AUTODETECTION 6

MANUAL CONFIGURATION OF A DIAL-UP CONNECTION (XP) 7

MANUAL CONFIGURATION OF DIAL-UP CONNECTION (WIN7) 10

APPLE IPHONE 5 14 BANDRICH BANDLUXE C320 15 BLACKBERRY TORCH 9810 19 DATANG DTM8101/DTM8120/LEADCORE LC8130E 22 HTC ONE XL 25 HUAWEI E180/E169/E182E/E1820/E270+/E367/ E392U-12/E372U-8 USB MODEM 31 HUAWEI E392U-12 32

CHANGING TCP/IP PROPERTIES 33

HUAWEI E3276S-150/861 35 HUAWEI C7600 37 HUAWEI E398 40 CHANGING TCP/IP PROPERTIES 43

KODIAK PTT 45 DRIVER INSTALLATION 45

PAIRING THE PHONE WITH THE LAPTOP 46

CONFIGURE AND CONNECT KODIAK PTT CLIENT VIA BLUETOOTH 49

ADDING KODIAK PTT DEVICE IN NEMO OUTDOOR 51


NETGEAR AIRCARD 340U 52 NOKIA LUMIA 920 (RM-821) 54 NOKIA 3500/6120/6121/6720(US)/ C5/C5-00.2/C5-03(US)/C5-04/C7-00/E7-00/N80/ N85(US)/N95(US)/N96(US)/N97(US) 56 NOKIA 500 59 NSN USB-LTE 7210 (ALTAIR) 61 MOTOROLA USBW 25100 65 SAMSUNG GALAXY S4 (GT-I9505, SGH-I337, SPH-L720, T-MOBILE SGH-M919), GALAXY S4 ACTIVE (GT-I9295), GALAXY S II (GT-I9210) 67 SAMSUNG GALAXY S II SKYROCKET, GALAXY S II HD LTE (SHV-E120S KOREAN VERSION) 69 SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710), GALAXY RUGBY, GALAXY S4 MINI (GT-I9195), GALAXY S4 4G+ (GT-I9506), GALAXY NOTE 3 (SM-N9005, SM-N900T TMOB) 72 SAMSUNG GALAXY S III (GT-I9305), GALAXY S II NOTE (GT-N7105) 74 SAMSUNG DROID CHARGE 77 LG C676/C680/VX8300/U900/KU950/KX206/KX256/ KF700/TU550 81 LG VX8350/VX8360 85 LG L1000 88 LG P930 91 HUAWEI E3276S-150/861 94 LG P500H 97 SIERRA WIRELESS AIRCARD 306/307/308/309/310/ 312U/313U/320U/330U, SIERRA COMPASS 889 HSPA USB MODEM, SIPTUNE SM215 98 SIERRA WIRELESS COMPASS 597 102 NOVATEL OVATION MC930D/MC990D/MC996D/MC998D/MC545 104 NOVATEL OVATION MC727/MC760 USB MODEM 106 PANTECH UM175 108 PANTECH UML290 111 ZTE MF820T/MF820D 114

CONTE NTS 5

ZTE MF668A 115 ZTE MF683 116 ZTE MF880 117 ZTE TU25 118 SONY ERICSSON XPERIA ARC S 120 ONDA MT689DC 129 APPLICATION TESTER 131


INTRODUCTION

The purpose of this document is to give step-by-step instructions for setting up dial-up networking for your computer in order to perform packet-switched data testing with the Nemo tool Nemo Outdoor. Furthermore, some of the test mobiles need to be configured before data testing is performed. The configuration instructions are provided in this document.

The usage of Nemo Outdoor is not explained in this document. The Nemo Outdoor User Manual included in the shipment gives detailed information on the Nemo Outdoor software and its usage.

Please note that the devices below have been removed from the current document. Dial-up instructions for these devices can be found in the Dial-up Networking Setup Guide version 7.10.

Audiovox PC5750/Pantech PX-500

Huawei EC169/EC169C USB Modem

LG G7/G13/G17

LG VL600

LG U900/KU950

Merlin U530/U740/X950D

Motorola V3x/V3XX/V3XXUS/V9/V9US

Nokia 6230i

Option GlobeTrotter 3G+/GT MAX 7.2 Ready/HSDPA 7.2/Express 7.2

Option iCon 452

Option GlobeSurfer iCON 7.2 USB modem

Qualcomm TM6250/6275/6280/7200/8200/ MDM9200/MDM9600

Samsung Z105/Z107/Z140/Z500/Z560/Z720/ZV10/ZX20/A707/G800/P920/P940/SHG-T639/SGH-U800/SHG-U900

Sierra Wireless Aircard 850/860

Sierra Wireless Aircard 880/881

Sierra Wireless Compass 885

Zapp Telemodem Z020

DEVICE AUTODETECTION

From Nemo Outdoor 5.60 onwards, it is possible to use autodetection to add devices to Nemo Outdoor. It is no longer necessary to manually install and configure a dial-up connection. Once a device is connected to a computer and the device driver is installed, it can be added fully automatically to Nemo Outdoor application using Autodetect Devices button. Nemo Outdoor will automatically detect the device trace and modem ports and assign a suitable dial-up connection.

INTRODUCTION 7

Autodetection works with all Nemo Outdoor test terminals verified by Anite Finland. In some cases it is possible that the terminal is not recognized and the autodetection does not work. If this happens, manually select the correct trace and modem ports. Then select Automatic in the Packet switched dial-up connection field and click Apply. If the automatic dial-up connection detection does not work, please see instructions below.

MANUAL CONFIGURATION OF A DIAL-UP CONNECTION (XP)

1. Select Start | Settings | Control Panel. Click on Network Connections. Select File | New Connection to start the New Connection Wizard. Click Next on the Welcome page.

2. Select Connect to the network at my workplace and click Next.

3. Select Dial-up connection as your Network Connection. Click Next.

4. Select the terminal from the list and click Next.


With Leadcore terminals, select the unnumbered Leadcore Technology DTM8100 Modem item, and click Next.

With Nokia terminals, select the item with the highest number and click Next.

With Nokia 7376 terminal, select the unnumbered Nokia USB Modem item and click Next.

5. Type a connection name, for example, Huawei, in the Company Name field. Click Next.

6. In the Telephone Number field, enter *99# (#777 for CDMA mobiles). Click Next.

7. Select Anyones use and click Next and Finish.

INTRODUCTION 9

8. See chapters from page 14 onwards for terminal-specific instructions on adding terminals to Nemo Outdoor.


MANUAL CONFIGURATION OF DIAL-UP CONNECTION (WIN7)

Select Start | Control Panel | Network and Internet. Select Network and Sharing Center | Set up a 1.new connection or network. Select Set up a dial-up connection, and click Next.

Select the correct terminal from the list and click Next. 2.With Nokia terminals, select the item with the highest number, e.g., in this case #3.

INTRODUCTION 11

In the Telephone Number field, enter *99# (#777 for CDMA terminals). In the Connection name 3.field type, for example, Nokia Dial-up connection. Select Allow other people to use this connection. Click Connect.

Click on Skip in the Connecting to xxx dial-up connection dialog. 4.

Click Close. 5.


Go to Control Panel | Network and Internet | Network and Sharing Center, and select Connect to a 6.network. Right-click on the Terminal Dial-up Connection, and select Properties.

In the Networking tab, deselect the Internet Protocol Version 6 (TCP/IPv6) item and select 7.Internet Protocol Version 4 (TCP/IPv4). Click OK.

Steps 8 and 9 apply only to Nokia terminals.

INTRODUCTION 13

Go to Device Manager (Start | Settings | Control Panel | System and Security | Device 8.Manager), and double-click on Modems. Right-click on the #3 item on the list and click Properties.

Select the Advanced tab, and type in atz in the Extra initialization commands field, and click on 9.OK.

See the following chapters for terminal-specific instructions on adding terminals to Nemo Outdoor. 10.


APPLE IPHONE 5

Apple iPhone 5 can be connected with Nemo Outdoor using the application tester handler.

Install iTunes on your computer. iTunes can be downloaded from 1.http://www.apple.com/itunes/download. Start iTunes.

On the iPhone 5 device, select Settings | Personal Hotspot and turn on the Personal Hotspot. 2.

Connect the USB connectivity cable to your PC. Device drivers are installed automatically. 3.

Go to Nemo Outdoor and select Measurement | Add New Device | Phone | Application Tester. 4.

Leave the Trace Port and Modem Port fields empty. 5.

Select as the Packet switched dial-up connection. Click OK. 6.

Activate a packet session manually before running scripts.

Note that when testing with iPhone 5, all other connections (WLAN, Ethernet cable, etc.) need to be disconnected.

Bandrich BandLuxe C320 15

BANDRICH BANDLUXE C320

Plug in the USB device in one of your PCs USB ports. The drivers are automatically installed, and 1.Windows automatically detects the device.

Select English in the Choose Setup Language dialog. 2.

Click on Next in the Welcome dialog that appears. 3.

Select I accept the terms in the license agreement in the License Agreement dialog, and click 4.Next.


Select a destination folder and click Next. 5.

Click Install to start the installation. 6.

Bandrich BandLuxe C320 17

Click Finish to finish the installation. 7.

Close the BandLuxe software that appears, as it will not be required in the following steps. 8.

Go to Start | Control Panel | System | Hardware | Device Manager. Under Modems you should be 9.able to see the BandLuxe 3.5G Modem, under Network adapters you should see the BandLuxe 3.5G Ethernet Adapter, and under Ports the BandLuxe Adapter Control Interface (COMxx) and BandLuxe AT CMD Interface (COMxx) items.


In Nemo Outdoor Device Configuration dialog, select the COM port number assigned to the 10.BandLuxe Adapter Control Interface item in the Trace Port field. Select the COM port number assigned to the BandLuxe 3.5G Modem item (right-click the item and select Properties) in the Modem Port field.

Blackb erry Torch 9180 19

BLACKBERRY TORCH 9810

Please note that currently the driver can be installed on 32-bit Windows only.

Install the device drivers. The file is located on the Nemo Outdoor USB flash drive. Browse the file manually and double-click the 610_b038_multilanguage file. The package will self-extract.

The Blackberry Desktop Software application is launched. Select the installation language and click 1.OK.

If the installer requests to install the Microsoft Visual C++ 2008 Redistributable file, click Install. 2.

Click Next to begin the Blackberry Desktop SW installation. 3.

Select your country or region and click Next. 4.


Accept the license agreement and click Next. 5.

Select the installation folder and click Next and Install. 6.

Wait until the installation is complete and click Finish. 7.

Close the Blackberry software that appears, as it will not be required in the following steps. 8.

Blackb erry Torch 9180 21

Go to Device Manager. Under Modems you should see the Standard Modem item and under Ports 9.two RIM Virtual Serial Port v2 items.

Connect the device USB cable to the device and to the Nemo Outdoor laptop. Select USB Drive 10.from the device screen.

Start Nemo Outdoor. Autodetection does not work with the Blackberry device so add the device 11.manually (Add New Device | Phone | Qualcomm).

In the Device Configuration dialog, select the COM port with the bigger number assigned to the 12.RIM Virtual Serial Port v2 item in the Trace Port field. Select the COM port with the smaller number in the Modem Port field. Select Automatic in the dial-up connection field.


DATANG DTM8101/DTM8120/LEADCORE LC8130E

Installing the connectivity cable driver:

Do not connect the connectivity cable to your PC until the driver installation is complete.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse the file manually and double-click the USB2VCOM_driver_x.xx.xx file (x is the latest driver version).

2. Select Uninstall old version first if installed, and click Install in the Leadcore Technology DTM8100 Series Driver Installer dialog.

3. In the VCOM Number field you need to select 3 ports for each test terminal. Since the driver is installed only once, select the number of COM ports according to how many Leadcore terminals you intend to use with Nemo Outdoor. Hence, if you want to connect two Leadcore terminals with Nemo Outdoor, select at least 6 in the VCOM Number field. Click Exit when the installation is done.

4. After the driver installation is finished, Windows may restart your computer but it is not required.

5. After your computer has restarted, connect the connectivity cable to the mobile and the other end to the computers USB port. Windows will detect the new hardware automatically and start the installation. The step is repeated several times until all new hardware is added.

6. In the Welcome page, select No, not this time and click Next.

Datan g DTM8101/DTM8120, Leadcore LC8130E 23

7. Select Install the software automatically (Recommended) and click Next.

8. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 6, 7 and 8 several times until the installation process is finished.

9. After installation, go to Device Manager. Select Start | Settings | Control Panel | System, open the Hardware tab and click the Device Manager button.

10. You should be able to see three Datang Mobile modems under Modems, and three Datang Mobile items under Ports.


11. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will find the COM port numbers needed in the next steps.

12. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

13. In the Device Manager click on Ports. Select the COM port number assigned to the Leadcore Technology DTM8100 Modem #2 item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Leadcore Technology DTM8100 Modem #3 item in the Modem Port field.

14. In the Device Configuration dialog, select or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). Click Apply.

15. If the device connecting fails, check that you have selected the correct COM ports and try again.

HTC On e XL 25

HTC ONE XL


Connect the device to the laptop. Select Charge only on the phone. 1.

Go to Device Manager. Under Other devices you should see the HTC DIAG, HTC Modem, and 2.RmNet items.

Right-click on the HTC DIAG item and select Update Driver Software. 3.


In the Update Driver SW HTC DIAG dialog, select Browse my computer 4.

Select Let me pick from a list 5.

HTC On e XL 27

Select Show All Devices and click Next. 6.

Click Have Disk. 7.

Browse to folder HTC_ONE_XL_Waikiki USB_drivers_20110310_unsigned\DIAG and select the 8.correct subfolder based on your operating system, e.g. \Win7_x86. Click OK.


Click Next. 9.

HTC On e XL 29

If the Windows Security dialog appears, click Install this driver anyway. The driver will be 10.installed. Click Close after the installation is finished.

The HTC DIAG item has disappeared and a new item HTC Diagnostic Interface appears under 11.Ports.

Now repeat the driver software update process for the HTC Modem and RmNet items. Ignore all 12.Windows warnings. The steps are otherwise the same but the driver files are located in different folders:

HTC Modem: HTC_ONE_XL_Waikiki USB_drivers_20110310_unsigned\Modem

RmNet: HTC_ONE_XL_Waikiki USB_drivers_20110310_unsigned\QMI

After you have updated all drivers, go to Device Manager. You should see the following items: 13.

Modems: HTC USB Modem

Network adapters: HTC Ethernet Adapter

Ports: HTC Diagnostic Interface


Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click 14.Phones and select the Qualcomm item. Click Next.

In the Nemo Outdoor Device Configuration dialog, define the following settings: 15.

Trace port: Select the COM port number assigned to the HTC Diagnostic Interface. Modem port: Select the COM port number assigned to HTC USB Modem Packet-switched dial-up connection: NDIS

Click Apply. 16.

If the device connecting fails, check that you have selected the correct COM ports and try again.17.

Huawei E 180/E 169/E182E/E1820/E 270+ /E367/E392u -12/392u-221/E372u -8 USB Mod em 31

HUAWEI E180/E169/E182E/E1820/E270+/E367/ E392U-12/E372U-8 USB MODEM

Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.


Next, ignore and close the Vodafone or Mobile Partner application that appears. It should not be on 2.while connecting the device with Nemo Outdoor later on.

You may need to restart the computer for the installation to take effect. 3.

Go to Start | Control Panel | Phone and Modem Options | Modems. You should see the Huawei 4.Mobile Connect 3G Modem item with its associated COM port number in the list.

Please note that with some Huawei E392U-12 devices the Huawei Mobile Connect 3G Modem item does not appear. If this happens, please follow the instructions in chapter Huawei E392u-12.

Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will 5.find the COM port numbers needed in the next steps.

Select Measurement | Add New Device. In the New Device dialog, click Phones and select the 6.Qualcomm item. Click Next.

In the Device Manager click on Ports. Select the COM port number assigned to the Huawei 7.Mobile Connect 3G Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number attached to the Huawei Mobile Connect 3G Modem item in the Modem Port field.

In the Device Configuration dialog, select or the previously made dial-up 8.connection as the Packet switched dial-up connection (see page 6). Click Apply.

If the device connecting fails, check that you have selected the correct COM ports and try again. 9.


HUAWEI E392U-12

Please note that with some Huawei E392U-12 devices the Huawei Mobile Connect 3G Modem item does not appear. If this happens, please follow the instructions below.

The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.


Next, ignore and close the Vodafone or Mobile Partner application that appears. It should not be on 2.while connecting the device with Nemo Outdoor later on.

You may need to restart the computer for the installation to take effect. 3.

Start Nemo Outdoor. Select View | Windows Device Manager. In the Device Manager, you 4.should see the following two items and their COM port numbers under Ports: Huawei Mobile Connect Application Interface and Huawei Mobile Connect PC UI Interface.

Select Measurement | Add New Device. In the New Device dialog, click Phones and select the 5.Qualcomm item. Click Next.

In the Device Manager click on Ports. Select the COM ports as follows: 6.

Trace port: Huawei Mobile Connect Application Interface

Modem port: Huawei Mobile Connect PC UI Interface

In the Device Configuration dialog, select or the previously made dial-up 7.connection as the Packet switched dial-up connection (see page 6). Click Apply.


Huawei E C169/E C169C USB Mod em 33

CHANGING TCP/IP PROPERTIES

Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older versions. Before measurements can be done with Nemo Outdoor, the Internet protocol properties must be manually changed to automatic mode. This must be done always after the modem is disconnected/reconnected and also if the device stops responding during measurements.

Windows XP:

Plug in the Huawei device. 1.

Go to Start | Control Panel | Network Connections, and right-click on Huawei Broadband 2.Connection, and select Properties.

In the Mobile Broadband Connection Properties dialog, select Internet Protocol Version 4 3.(TCP/IPv4) and click on Properties.

Select Obtain an IP address automatically and Obtain DNS server address automatically. 4.

Windows 7:


Go to Start | Control Panel | Network and Internet | Network and Sharing Center. 2.

Click on Change adapter settings. 3.

Right-click on Mobile Broadband Connection and select Properties. 4.



Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK 6.and OK.

HUAWEI E3276s-150/861 35

HUAWEI E3276S-150/861

1. Connect the device to your computers USB port. Windows will detect the new hardware automatically and start the installation. Click Run AutoRun.exe and follow the instructions on the screen.

2. When the installation is finished, Windows XP users are advised to reboot the computer.

3. The Telenor Mobile Partner software starts up. Please note that outlook of the Mobile Partner software varies depending on operator etc. Close the program.



5. You should see the Huawei Mobile Connect 3G Application Interface item and the Huawei Mobile Connect Application Interface items under Ports.

6. Install the Hisi UE Agent to default installation folder. The file is located on the Nemo Outdoor USB

flash drive. Browse to folder \Nemo Outdoor 7.x\Drivers\HiSilicon\ Hisi UE Agent B211 and run

the Hisi UE Agent Balong V700R001C50B211.exe file. NOTE! After the installation is finished, Hua.exe file must be located under folder C:\Hisi UE Agent\bin\hua.exe.

7. Install Huut- Huawei UE Update Tool 1.3 (Nemo Outdoor 7.x\Drivers\HiSilicon\Huut-V1.3.) This is

necessary if no diagnostics have been activated yet in UE. Activation can only be performed by

Huawei.

8. Start Huut- Huawei Update Tool and generate the file. Send the file to Huawei.

9. Update file (key) provided by Huawei with Huut- Update tool. Update file is generated based on

IMEI of UE.

10. Add the device to Nemo Outdoor by using autodetection. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will find the COM port numbers needed in the next steps.

11. The device can also be added manually. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the HiSilicon item. Click Next.

12. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect 3G Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect Application Interface item in the Modem Port field.

13. In the Device Configuration dialog, select as the Packet switched dial-up connection. Click Apply.


HUAWEI C7600 37

HUAWEI C7600

Do not connect the USB data cable to your PC until the driver installation is complete.

1. The data cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder D:\Drivers\Drivers for Qualcomm Based Devices\Huawei C7600 and run the driver .exe file.

2. Click Install in the DriverInstall Setup: Installation Options dialog.

3. Click Close in the DriverInstall Setup: Completed dialog.

4. After the installation has finished, connect the USB connectivity cable to your phone, and the other end of the cable to your computers USB port. Windows will detect the new hardware automatically and start the installation.




7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished. Click Finish to exit the wizard.


9. You should see the HUAWEI CDMA Handset Modem item under Ports.

HUAWEI C7600 39


11. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.

12. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei CDMA Handset Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number attached to the Huawei CDMA Handset - Modem item in the Modem Port field.




HUAWEI E398

Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up every time the device is plugged in and it must be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be renamed. A reinstall warning will be displayed when device is plugged in but this can be ignored.




HUAWEI E398 41


5. You should see the Huawei Mobile Connect Modem item under Modems and the Huawei Mobile Connect Application Interface and Huawei Mobile Connect PC UI Interface items under Ports.


7. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.

8. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect PC UI Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect - Modem item in the Modem Port field.

Huawei E C169/E C169C USB Mod em 43

CHANGING TCP/IP PROPERTIES

Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older versions. Before measurements can be done with Nemo Outdoor, the Internet protocol properties must be manually changed to automatic mode. This must be done always after the modem is disconnected/reconnected and also if the device stops responding during measurements.

Windows XP:


Go to Start | Control Panel | Network Connections, and right-click on Huawei Broadband 2.Connection, and select Properties.


Select Obtain an IP address automatically and Obtain DNS server address automatically. 4.

Windows 7:


Go to Start | Control Panel | Network and Internet | Network and Sharing Center. 2.

Click on Change adapter settings. 3.

Right-click on Mobile Broadband Connection and select Properties. 4.



Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK 6.and OK.

Kodiak PTT 45

KODIAK PTT

DRIVER INSTALLATION

The first step is to install drivers for the Bluetooth adapter. The driver file (IOGEAR Bluetooth 4.0 1.USB Micro Adapter GBU521 Driver Win Vista 7 v6.5.1.2700) can be downloaded from the Nemo User Club (nemouserclub.anite.com) or from http://www.iogear.com/support/dm/driver/GBU521#display

Run the Autorun.exe file. 2.

Wait until the driver has been installed. 3.

Agree to install the Bluetooth service. 4.

Plug in the USB to Bluetooth module to your Nemo Outdoor laptop when prompted. 5.

When installation is ready, press Finish. 6.

Go to Control Panel | Hardware and Sound | Devices and Printers. You should see the 7.BCM920702 Bluetooth 4.0 device.


Right click the Bluetooth device and select Bluetooth settings. 8.

Select the Show the Bluetooth icon in the notification area option. 9.

PAIRING THE PHONE WITH THE LAPTOP

Check the computer name from the Device Manager. 1.

Enable Bluetooth on your Kodiak PTT phone. 2.

Kodiak PTT 47

Enable your device visibility. 3.

Select Add a Device from the Bluetooth menu on your laptop and follow the wizard to add the 4.phone.


Confirm the pairing code and click Next. 5.

You should now see your phone as a device in the Devices and Printers view. 6.

Kodiak PTT 49

CONFIGURE AND CONNECT KODIAK PTT CLIENT VIA BLUETOOTH

Launch the Kodiak PTT client on the phone. 1.

On your laptop, go to Control Panel - Hardware and Sound, right-click the device (your phone) and 2.select Properties.

On the Services page, select the Serial port (SPP) KodiakPoCApplication option. 3.

Click OK and a Bluetooth serial port will be installed. 4.


Go back to the PTT1 Properties, Services page. You should now see a COM port assigned for the 5.Serial port.

You should also see a COM port under Ports in Device Manager. 6.

Kodiak PTT 51

ADDING KODIAK PTT DEVICE IN NEMO OUTDOOR

Device can be added using either the terminal specific handler or the Application Tester handler. 1.These steps will show the usage with the Application Tester handler.

Launch Nemo Outdoor. 2.

Add a new device (Application Tester) and click Next. 3.

In the Kodiak PTT port field, select the COM port that was assigned for the Standard Serial over 4.Bluetooth link item (check from Device Manager, Ports).

When using the Application Tester handler, there is no need to configure the Trace or Modem 5.ports. Also dial-up connections can be Not Used if only Kodiak testing will be performed.

Press OK to add the device. You are now ready to start the measurements.6.


NETGEAR AIRCARD 340U


Go to Network adapter settings and select Never connect automatically in the Autoconnect 2.field.

After installation, go to Device Manager. You should see the following items: 3.Modems: Sierra Wireless WWAN Modem Ports: Sierra Wireless DM Port

Netgear Ai rcard 340U 53



Trace port: Select the COM port number assigned to Sierra Wireless DM Port Modem port: Select the COM port number assigned to Sierra Wireless WWAN Modem

In the Device Configuration dialog, select or the previously made dial-up connection as 6.

the Packet switched dial-up connection (see page 6). Click Apply.



NOKIA LUMIA 920 (RM-821)

Do not connect the USB connectivity cable to your PC until the driver installation is complete.

11. First, uninstall any existing Qualcomm drivers.

12. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder Nemo Outdoor\Nemo Outdoor x.x\Drivers\Qualcomm\Nokia\Lumia 920 RM-821\USB Host Driver 1.00.12\72 and run the setup.exe file.

13. Click Next in the Welcome dialog. Select I accept in the License Agreement dialog and click Next.

14. Click Install and finally Finish.

15. After the connectivity cable driver installation is finished, Windows may restart your computer but it is not required.


Please note that with newer Nokia devices the Wizard may not appear at all and instead the installation is performed automatically.



19. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times until the installation process is finished.

Nokia Lumia 920 (RM-821) 55

20. After installation, go to Device Manager. You should see the following items: Modems: Qualcomm HS-USB Modem 9001 Network adapters: Qualcomm HS-USB WWAN Adapter Modem 9001 Ports: Qualcomm HS-USB Diagnostics 9001

21. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the Qualcomm item. Click Next.

22. In the Nemo Outdoor Device Configuration dialog, define the following settings:

Trace port: Select the COM port number assigned to Qualcomm HS-USB Diagnostics 9001 Modem port: Select the COM port number assigned to Qualcomm HS-USB Modem 9001




NOKIA 3500/6120/6121/6720(US)/ C5/C5-00.2/C5-03(US)/C5-04/C7-00/E7-00/N80/ N85(US)/N95(US)/N96(US)/N97(US)



With Nokia C5-03(US), C5-04, C7-00 and E7-00 the following settings are recommended to improve stability:

Set Theme effects to OFF Set Animated background to OFF Set Call image to none Set Screen saver to none Delete additional home screens Set widgets to offline mode Set WLAN scanning to OFF Set sensors to OFF 1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder

Nemo Outdoor x.xx\Drivers\Nokia drivers and run the Nokia_Connectivity_Driver_xxx.x.msi file (x is the latest driver version).

2. Click Next in the Welcome dialog. Select I accept in the License Agreement dialog and click Next.

3. Please read the safety notes carefully and then click Next in the Safety Information dialog.

4. Choose the destination folder and click Install.

5. Click Yes in the Digital Signature Not Found dialog if it appears. Otherwise, click Install.

6. After the connectivity cable driver installation is finished, Windows may restart your computer but it is not required.

Nokia 3500/6120/6121/6720(US)/C5/C5 -00.2/C5-03(US)/C5-04/C7-00/E 7-00/N80/N85(US)/ N95(US)/N96(US)/N 97(US) 57


Please note that with newer Nokia devices the Wizard may not appear at all and instead the installation is performed automatically.



10. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times until the installation process is finished.


12. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


13. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the terminal. Click Next.

14. In the Device Manager click on Modems. Select the COM port number assigned to the first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in the Modem Port field.



Nokia 500 59

NOKIA 500



1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder Nemo Outdoor x.xx\Drivers\Nokia drivers\Nokia 500 and run the Nokia_Suite_webinstaller_All file.

2. When the installation starts, choose your language and click Install.

3. Click I accept.

4. After the Nokia Suite installation is finished, close the installation dialog and connect the connectivity cable to the mobile and the other end to the computers USB port. Windows will detect the new hardware automatically and install the drivers.

5. After installation, go to Device Manager. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



7. In the Device Manager click on Modems. Select the COM port number assigned to the first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in the Modem Port field.



NSN USB-l te 7210 61

NSN USB-LTE 7210 (ALTAIR) Do not connect the USB connectivity cable to your PC until the driver installation prompts you

to do so.

1. First the Connection Manager is installed. The installation file is located on the Nemo Outdoor USB flash drive. Browse the file and double-click the LTE7210_xxxx_EngineeringRelease.exe file (xxxx refers to the version number).

2. First select the Installer language and click OK.

3. Click Next in the Welcome dialog. Click I Agree in the License Agreement dialog.

4. Choose the destination folder and click Next.

5. If at some point you see the Select Components dialog, select Full Installation and click Next.


6. Define the Start Menu Folder and click Install.

7. At some point during the Connection Manager installation, the Device Driver Installation Wizard starts up automatically. Click Next in the Welcome dialog.

NSN USB-l te 7210 63

8. The device driver installation is completed and you can now connect the device to your computer. Click Finish.

9. Windows will automatically detect the new hardware and install the required drivers.

10. Return to the Connection Manager installation. When the installation is complete, click Finish.


11. The Connection Manager will launch automatically but it is important that it is closed before adding the device to Nemo Outdoor. It is recommended that you rename the .exe file that launches the Connection Manager to prevent the CM from starting. Browse to C:\Program Files \NSN LTE Connection Manager (or for 64-bit Windows C:\Program Files (x86)\NSN LTE Connection Manager) and rename the nsnltecm.exe to nsnltecm.exe_.

12. To avoid performance issues with the modem, the Altair LogCreator standalone functionality needs to be disabled. Browse to folder C:\Program Files\NSN LTE Connection Manager\Tools\ Internals\LogCreator and open file RunLogCreator.bat with Notepad. Modify the following string:

Original: LogCreator.exe -SA -FN:"50" -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

Modified: LogCreator.exe -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

13. Go to Device Manager. Under Ports you should see Nokia Siemens Networks LTE Application Interface item.

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog, click Phones and select Altair. Click Next.


Trace port: Select Altair USB Modem port: Select the COM port number assigned to the Nokia Siemens Networks LTE

Application Interface 16. In the Device Configuration dialog, select and click Apply.

17. If the device connecting fails, check that you have selected the correct COM ports and try again. Also check that the NSN Connection Manager is not running.

Motoro la USBW 25100 65

MOTOROLA USBW 25100


Run the ClearCM_v1.05.0035.exe file on the Nemo Outdoor USB flash drive. 1.

Wait until extraction and installation finishes (no input from user required) and until Clear 2.Connection Manager starts up.

When CLEAR Connection Manager is running (no device detected), connect the device to a free 3.USB port.

The Connection Manager automatically installs the drivers; when done, it will start searching for a 4.network.

Go to Device Manager in Start | Settings | Control Panel | System | Hardware. Double-click on 5.the Network adapters item. The WiMAX Network Adapter item should be in the list.


Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will 6.find the COM port numbers needed in the next steps.

Select Measurement | Add New Device. In the New Device dialog, click Phones and select the 7.terminal. Click Next.

In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port field in the 8.Device Configuration dialog. Leave the Modem Port field empty.

In the Device Configuration dialog, select or the previously made dial-up connection 9.as the Packet switched dial-up connection (see page 6). Click Apply.


Note that the connection must be activated via the Clear Connection Manager, which also needs to be running during measurements, for the device to work with Nemo Outdoor.

Samsun g Galaxy S4 (GT-I9505, SGH - I337, SPH-L720, T -Mob i le SGH-M919) , Ga laxy S4 Act ive (GT- I9295), Ga laxy S I I (GT- I9210) 67

SAMSUNG GALAXY S4 (GT-I9505, SGH-I337, SPH-L720, T-MOBILE SGH-M919), GALAXY S4 ACTIVE (GT-I9295), GALAXY S II (GT-I9210)



Check that the Mobile data setting is disabled from the device. Pull down the menu from the top of the device screen and check that the Mobile data setting is grayed out. Also check that WiFi and Bluetooth are disabled.

Insert the Nemo Outdoor USB flash drive and browse to the driver folder (e.g. Nemo 1.Outdoor\Nemo Outdoor xxx\Drivers\Qualcomm\Samsung\Samsung Galaxy S4). Double-click the SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_22_0.exe file to start the installation. Follow the steps in the installation wizard.

When the installation is complete, connect the terminal to your PC with the USB cable. Windows 2.will install the device drivers automatically.


Go to Device Manager. Under Ports, you should see two Samsung Mobile USB Serial Port 3.items.



Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port with the bigger number. If device connecting fails, try the other port.

Modem port: Select the COM port number assigned to Samsung Mobile USB Modem Packet-switched dial-up connection: NDIS

Click Apply. 6.


Samsun g Galaxy S I I Skyrocket , Galaxy S I I HD LTE (SHV-E 120S) 69

SAMSUNG GALAXY S II SKYROCKET, GALAXY S II HD LTE (SHV-E120S KOREAN VERSION)



1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next in the Welcome dialog.

2. Select your language and country from the list and click Next.


3. Select the installation location and click Install.

4. The driver files are installed. Wait until the installation is finished and click Exit.

5. Switch on the mobile. Connect the USB cable to the mobile and the other end of the cable to a USB port on your computer. Wait for Windows to detect the device.

Samsun g Galaxy S I I Skyrocket , Galaxy S I I HD LTE (SHV-E 120S) 71

6. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Modems you should see the Samsung Mobile USB Modem item and under Ports you should see the Samsung Mobile USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port with the bigger port number (in the example above, COM53)

Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem 9. In the Device Configuration dialog, select or the previously made dial-up connection as

the Packet switched dial-up connection (see page 6). Click Apply.

10. If the device connecting fails, select the Samsung Mobile USB Serial Port with the smaller port number and try again.


SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710), GALAXY RUGBY, GALAXY S4 MINI (GT-I9195), GALAXY S4 4G+ (GT-I9506), GALAXY NOTE 3 (SM-N9005, SM-N900T TMOB)



If the Samsung Galaxy S III terminal has been used with Nemo Handy, the device needs to restarted or powered off/on before connecting it with Nemo Outdoor.

With Galaxy S4 Mini (GT-I9195), Galaxy S4 4G+ (GT-I9506), and Galaxy Note 3 (SM-N9005, SM-N900T TMOB): Check that the mobile data setting is disabled from the device. Pull down the menu from the top of the device screen and check that the mobile data setting is grayed out. Also check that WiFi and Bluetooth are disabled.

Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo 1.Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy S III). Double-click the Samsung USB Driver for Mobile Phones 1.5.22.0.exe to run the installation.

When the installation is complete, connect the device to the PC. 2.

Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port item. 3.Under Modems you should see the Samsung Mobile USB Modem item.


Samsun g Galaxy S I I I (SGH-I747, SGH -T999, SCH -I535, SPH -L710), Ga laxy Rugby , Galaxy S4 Mini (GT-I9195), Galaxy S4 4G+ (GT-I9506), Ga laxy Note 3 (SM-N9005, SM-N900T TMOB) 73


Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port (in the example above, COM34)

Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem. Note! For Galaxy Note 3 (SM-N9005 variant only), select Not used.

In the Device Configuration dialog, select or the previously made dial-up connection as the 6.Packet switched dial-up connection (see page 6). Click Apply.


To be able to make voice calls, the voice call method must be selected in Nemo Outdoor (Devices view - Voice call method - Trace interface). For Samsung Galaxy S III SGH-T999 and SGH-i747, select Trace interface 2. With S4 variants, leave the field empty.


SAMSUNG GALAXY S III (GT-I9305), GALAXY S II NOTE (GT-N7105)

If the terminal has been used with Nemo Handy, the device needs to restarted or powered off/on before connecting it with Nemo Outdoor.

When the UE is used with Nemo Outdoor, other terminals cannot be used simultaneously in data testing if the NDIS interface is used to activate PS data connection. For example, simultaneous data testing with Huawei LTE modem and Samsung Galaxy S III handset is not possible. It should be noted that the issue does not limit using multiple Galaxy S III terminals for simultaneous data testing or together with non-NDIS terminals, such as, Nokia test terminals.

To be able to make voice calls the Trace interface 2 call method must be selected in Nemo Outdoor (Devices view - Voice call method - Trace interface 2).

.

Automatic answering to incoming calls can be done only when a headset is connected to the terminal. Use the original headset included in the sales package. Connect the headset to the phone and from the phone menu select: Settings -> Call Answering/ Ending-> Press arrow Accessibility -> Call Settings -> Accessory Settings For Call -> Automatic Answering. Automatic answering will operate only with the headset connected.

Auto detection should not be used to add the device. Add the device manually.

Samsun g Galaxy S I I I (GT-I9305), Ga laxy S I I Note (GT-N7105) 75

Check that Enable USB auto tethering option is selected.

USB mode must be RDNIS + DIAG + MODEM. Otherwise handset cannot be used with Nemo Outdoor/ Invex. This is selected automatically when application is installed. Return to main menu.

If data testing is done manually without script files, recording must be started before data protocols can be accessed via Nemo Outdoor. Without recording, the data protocol options in the UI are not available.

The following settings should be activated from the phone for data testing:

Settings -> More settings -> Mobile networks -> Mobile data enabled-> Enable

For Samsung Galaxy S III: Settings -> More settings -> Mobile networks -> Network Mode -> AUTO

For Samsung Galaxy S II Note: Settings -> More settings -> Mobile networks -> Network Mode -> Network Mode -> LTE/GSM/WCDMA (Auto mode)

With Samsung Galaxy S III (GT-i9305) and Samsung Galaxy S II Note (GT-N7105): The device is always online. This means that attach/detach and PDP context activation/deactivation commands cannot be used via Nemo Outdoor. It is recommended that the access point name (APN) is defined for the phone manually. Otherwise the phone can choose an incorrect APN automatically and this may cause the packet session to fail.



Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo 1.Outdoor\Nemo Outdoor xxx\Drivers\Qualcomm\Samsung\Samsung Galaxy S III). Double-click the Kies_x.x.x.exe to start the installation.

Select the installation language. 2.

Select I accept in the License Agreement dialog and click Next. Wait for the installation to finish. 3.It may take several minutes.

If the Samsung Kies software starts, close the program. If the program suggests a driver update, 4.do not update.

When the installation is complete, connect the terminal to your PC with the USB cable. Windows 5.will install the device drivers automatically.


Go to Device Manager. Under Ports, you should see the Samsung Mobile USB Serial Port item. 6.



Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial Port (in the example above, COM15)

Modem port: Select Not Used. Packet-switched dial-up connection: Automatic

Click Apply. 9.


Samsun g Droid Charge 77

SAMSUNG DROID CHARGE



1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next in the Welcome dialog.

2. Select your language and country from the list and click Next.

3. Select the installation location and click Install.


4. The driver files are installed. Wait until the installation is finished and click Exit.

5. Switch on the mobile. Connect the USB cable to the mobile and the other end of the cable to a USB port on your computer. Wait for Windows to detect the device.

6. Enable USB tethering from the mobile (Menu Settings - Wireless & networks - Tethering & portable hotspot, select USB tethering). Wait for Windows to finish the driver installation.

Samsun g Droid Charge 79

7. When the installation is complete, check from the Device Manager (Start | Settings | Control Panel | System | Hardware | Device Manager) that the installation was successful. Under Network adapters you should see the Samsung Android USB Remote NDIS Network Device item and under Ports you should see the Samsung Android USB Diagnostic Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


9. In the Nemo Outdoor Device Configuration dialog, define the following settings and click Apply:

Trace port: Select the COM port number assigned to the Samsung Android USB Diagnostic Serial Port (in the example above, COM102)

Packet switched dial-up connection: Select or the previously made dial-up connection (see page 6).

LG C676/C680/VX8300/U900/KU950/KX206/KF700/TU550 81

LG C676/C680/VX8300/U900/KU950/KX206/KX256/ KF700/TU550


Do not connect the USB connectivity cable to your PC until the connectivity cable driver installation is complete.

The LG KF700 USB driver conflicts with the LG USB driver for CDMA terminals. If both drivers are installed on the same computer, the terminals are not detected.

The connectivity cable driver is located on the Nemo Outdoor USB flash drive. With LG C676, 1.C680, and KX 206, browse to folder D:\Drivers\Qualcomm CDMA drivers, and run the LGUSBModemDriver.exe file. With the LG VX8300 terminal, browse to folder D:\Drivers\Qualcomm US Specific Softwares, and run the LGUSB Driver_Eng__Ver_x.x.exe file (x is the latest driver version). With U900/KU950/KX206/KX256/KF700/TU550, browse to folder D:\Drivers\Qualcomm Specific Softwares\LG USB Driver v.3.35.0.600\Driver and run the Setup.exe file.

On the InstallShield Wizard welcome page click Next. 2.

If a Software Installation warning appears, click Continue Anyway. You may need to repeat this 3.step two or three times.

Click OK in the Information dialog. Next, connect one end of the connectivity cable shipped with the 4.mobile phone to the mobile, and the other end to the computers USB port. Windows will detect the new hardware automatically and start the installation.

In the Welcome page, select No, not this time and click Next. 5.


Select Install the software automatically (Recommended) and click Next. 6.

Click Continue Anyway or Yes in the Hardware Installation or Digital Signature Not Found 7.dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the installation process is finished.

LG C676/C680/VX8300/U900/KU950/KX206/KF700/TU550 83

The USB driver has now been installed. Click Finish. 8.

You need to restart your computer for the installation process to take effect. Click Yes in the 9.System Settings Change dialog.

After installation, select Start | Settings | Control Panel | Phone and Modem Options, then open 10.the Modem tab.

Under the Modem item you should see the created LGE CDMA USB Modem and the port 11.attached to it, in this example COM 17.

Go to Device Manager by selecting Start | Settings | Control panel | System | Hardware. In the 12.Device Manager you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



In the Device Manager click on Ports. Select the COM port number assigned to the LGE CDMA 14.USB Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



LG VX8350/VX8360 85

LG VX8350/VX8360


Insert the Nemo Outdoor USB flash drive in the USB port. Browse to folder D:\Drivers\Qualcomm 1.Specific Softwares\LGUSBModemDriver.exe.

Double-click the .zip file. Click Unzip. This will extract files to a folder in your C drive. Click Close. 2.

Switch on the mobile. Connect one end of the USB data cable to the terminal and the other end to 3.an empty USB port on your PC.

Windows will automatically detect the new hardware. Select No, not this time in the Found New 4.Hardware Wizard and click Next.

Select Install from a list or specific location and click Next. 5.

Select Include this location in the search and browse to folder D:\Nemo Drivers\LG VX8x00 6.driver on the Nemo Outdoor USB flash drive. Click Next.


The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is 7.ready to be used.

When the installation is complete, check from the Device Manager that the installation was 8.successful. Under Modems you should see the LGE CDMA USB Modem, and under Ports you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

LG VX8350/VX8360 87


In the Device Manager click on Ports. Select the COM port number assigned to the LGE CDMA 10.USB Serial Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




LG L1000

Do not plug in the data card before installation!

1. Browse to folder D:\Drivers\LG LTE USB Modem on the Nemo Outdoor USB flash drive. Run the LGE Setup_PcUSBDrv20(xxxxxxxx).msi file to start the installation wizard.

2. Click Next in the Welcome window that appears.

3. Click Install in the Ready to Install window.

4. Click Finish in the InstallShield Wizard Completed window.

LG L1000 89

5. Plug in the data card. Windows will automatically detect the new hardware. Select No, not this time and click Next.

6. Select Install the software automatically and click Next.

7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if it appears. You may need to repeat steps 6, 7 and 8 several times until the installation process is finished.


9. You should see the LGE USB Modem under Modems, and LG Electronics LTE Miniport Driver under Network adapters. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.



11. In the Device Manager click on Modems. Select the port assigned to LGE USB Modem in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.



LG P930 91

LG P930

Do not plug in the device before installation!

Run the LGUnitedMobileDriver_S4981MAN36AP22_ML_WHQL_Ver_3.6.exe file found on the 1.Nemo Outdoor USB flash drive to start the installation wizard.

First select the setup language and click Next. 2.

Click Next in the Welcome dialog. The driver will be installed. 3.

Click OK in the driver installed successfully message. 4.


Plug in the device. Enable USB tethering from the mobile (Menu Settings - Wireless & networks - 5.Tethering & portable hotspot, select USB tethering).

Please note that if the USB connection is disconnected (i.e. device is unplugged), the USB tethering must be re-enabled on the phone in order to use the data connection.

Windows will automatically detect the new hardware. Select No, not this time and click Next. 6.

Select Install the software automatically and click Next. 7.

Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation dialog if 8.it appears. You may need to repeat steps 6, 7 and 8 several times until the installation process is finished.

After installation, go to Device Manager. You should see the LGE AndroidNet USB Modem item 9.under Modems and LGE AndroidNet For Diagnostics Port under Ports. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

LG P930 93


In the Device Manager click on Modems. Select the port assigned to LGE AndroidNet For 11.Diagnostics Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE AndroidNet USB Modem in the Modem Port field.

Select as the Packet switched dial-up connection (see page 6). Click Apply. 12.

When using the device in LTE, do not issue manual packet session commands. If the connection needs to be disconnected, use Radio On/Off commands.

If you are making voice calls, issue an "ATS0=1" AT command to enable the incoming calls. This must be done every time the phone is restarted.


HUAWEI E3276S-150/861





HUAWEI E3276s-150/861 95

5. You should see the Huawei Mobile Connect 3G Application Interface item and the Huawei Mobile Connect Application Interface items under Ports.

6. Install the Hisi UE Agent to default installation folder. The file is located on the Nemo Outdoor USB

flash drive. Browse to folder \Nemo Outdoor 7.x\Drivers\HiSilicon\ Hisi UE Agent B211 and run

the Hisi UE Agent Balong V700R001C50B211.exe file. NOTE! After the installation is finished,

Hua.exe file must be located under folder C:\Hisi UE Agent\bin\hua.exe.

7. Install Huut- Huawei UE Update Tool 1.3 (Nemo Outdoor 7.x\Drivers\HiSilicon\Huut-V1.3.) This is

necessary if no diagnostics have been activated yet in UE. Activation can only be performed by

Huawei.

8. Start Huut- Huawei Update Tool and generate the file. Send the file to Huawei.

9. Update file (key) provided by Huawei with Huut- Update tool. Update file is generated based on

IMEI of UE.

10. Add the device to Nemo Outdoor by using autodetection. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager you will find the COM port numbers needed in the next steps.

11. The device can be added manually. Select Measurement | Add New Device. In the New Device dialog, click Phones and select the HiSilicon item. Click Next.

12. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei Mobile Connect 3G Application Interface item In the Trace Port field in the Device Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect Application Interface item in the Modem Port field.

LG P500H 97

LG P500H

Do not plug in the device before drivers are installed!

1. Browse to folder Drivers\Qualcomm based devices\LG WCDMA terminals\LG P500H on the Nemo Outdoor USB flash drive.

2. Run the LGAndroidPlatformDriver_WHQL_ML_Ver_1.2_All_Win7.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. After the device driver installation is finished, connect the terminal to the computer with a USB cable. Windows will automatically detect the new hardware and install drivers. Wait until the installation process is finished.

4. After installation, go to Device Manager. You should see the LGE Android Platform USB Modem item under Modems and LGE Android Platform USB Serial Port item under Ports.


6. Select the port assigned to LGE Android Platform USB Serial Port in the Trace Port field in the Device Configuration dialog. Select the port assigned to LGE Android Platform USB Modem in the Modem Port field.

7. In the Device Configuration dialog, select as the Packet switched dial-up connection (see page 6). Click Apply.



SIERRA WIRELESS AIRCARD 306/307/308/309/310/ 312U/313U/320U/330U, SIERRA COMPASS 889 HSPA USB MODEM, SIPTUNE SM215

1. Plug in the USB data card. The data card automatically starts the 3G Watcher driver installation. Siptune SM215 comes with its own driver installation software on a separate USB stick. Follow the instructions below.

2. Click OK in the Welcome dialog that appears.

3. Click Next in the Telstra Turbo Connection Manager Welcome window. Note that the name of the installation wizard may vary depending on the operator in question.

Sierra Wire less A ircard 30x/31x/320U/330U, S ierra Compass 889 HSPA USB Mod em, S iptun e SM215 99

4. Select I accept the terms in the license agreement in the License Agreement dialog, and click Next.

5. Click on Finish in the InstallShield Wizard Completed window.

6. Windows automatically detects the device.

7. The driver files are installed.

8. Open the Telstra Turbo Connection Manager main view. Note that the name of the Connection Manager may vary, for example, depending on the operator the device comes equipped with. For example, Sierra Wireless Watcher comes with Sierra 306.

9. Select Tools | Options. In the User Options window, select No in the Autolaunch on device insertion or power-up Do nothing for the On exit field or No in Turn radio off on exit Never for Check for updates


10. When these options are selected, you can close the Telstra Turbo Connection Manager/Watcher application, and the device will work in Nemo Outdoor. However, if these options are not selected, the Telstra Turbo Connection Manager/Watcher application needs to run in the background while conducting measurements with the Sierra device in Nemo Outdoor.

Note that the options may vary depending on the device. For example, with Sierra 306, the Tools button is a spanner icon, and instead of On exit field there is Enable airplane mode on exit which needs to be set to No. In addition, the modem name may change depending on the device, for example, to Sierra Wireless HSPA modem.

11. When the installation is complete, check from the Device Manager that the installation was successful. Go to Start | Control Panel | System and Security | System | Device Manager. Under Modems you should see a Sierra Wireless AirCard HSDPA Modem item and under Ports pay attention to the Sierra Wireless AT Command Port (UMTS) (COMxx) and Sierra Wireless DM Port (UMTS) (COMxx) items. Under Network Adapters you should see the Sierra Wireless HSPA Network Adapter item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Sierra Wire less A ircard 30x/31x/320U/330U, S ierra Compass 889 HSPA USB Mod em, S iptun e SM215 101


12. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless DM Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Sierra Wireless AT Command Port item in the Modem Port field.




SIERRA WIRELESS COMPASS 597

1. Insert the USB data card in a free USB slot on your PC.

2. The Sprint SmartView installation setup starts automatically. Double-click on the setup.exe file, and click Setup.

3. Click Next in the Welcome window that appears.

4. In the License Agreement window, select I accept the terms in the license agreement, and click Next.

5. Click Next in the Destination folder dialog.

6. Click Install.

7. After the installation is completed, the software will ask you to restart your computer. Click Yes.

8. Go to Start | Control Panel | System | Hardware | Device Manager. Double-click on Modems to expand it. You should see the Sierra Wireless Compass 597 EVDO Modem item. You should also see the Sierra Wireless Compass 597 DM Port (COMxx) item under Ports. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Sierra Wire less Compass 597 103


10. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra Wireless Compass 597 DM Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




NOVATEL OVATION MC930D/MC990D/MC996D/MC998D/MC545

1. Prior to plugging the USB modem in your computer, please refer to the Novatel quick start guide included in the product package for computer system requirements.

2. Insert the (U)SIM card supplied by your service provider in the terminal. Please refer to the quick start guide for more detailed instructions as to how to do this.

3. Insert the Novatel Ovation USB modem into your PC USB port.

4. Windows will automatically install the device driver and detect the new device. In addition, it automatically installs MobiLink Lite which is the device software. Ignore this software, and close it. It should not be on when adding the device to Nemo Outdoor.

5. Next, go to Start | Control Panel | Phone and Modem Options | Modems on your PC. The list should display Novatel Wireless Modem item and the associated COM port number, in this case COM26.

6. When the installation is complete, check from the Device Manager that the installation was successful. Under Modems you should see the Novatel Wireless Modem item and under Ports you should see the Novatel Wireless Application Port, Novatel Wireless EAP-SIM Port and Novatel Wireless Status Port items. Under Network adapters you should see the Novatel Wireless Network Adapter item. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.

Novatel Ovat ion Mod em MC930D/MC990D/MC996D/MC998D/MC545 105

7. Exit the MobiLink Lite application before starting Nemo Outdoor.


9. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Application Port item in the Trace Port field in the Device Configuration dialog. Click on Modems. Select the COM port number assigned to the Novatel Wireless Modem item in the Modem Port field.

10. In the Device Configuration dialog, select or the previously made dial-up connection as the Packet switched dial-up connection (see page 6). For Novatel Ovation 996D and 998D select in the PS Dial-Up Connection field. Click Apply.



NOVATEL OVATION MC727/MC760 USB MODEM

1. Plug in the Novatel Ovation USB modem data card.

2. Windows will automatically detect the new hardware. Select No, not this time and click Next.

3. Select Install from a list or specific location and click Next.

4. Select Include this location in the search and browse to folder D:\Nemo Drivers\Novatel MC727 usb drivers on the Nemo Outdoor USB flash drive. Click Next.

5. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new hardware is ready to be used.

Novatel Ovat ion Modem MC727 107

6. When the installation is complete, check from the Device Manager that the installation was successful. Under Ports you should see the Novatel Wireless Ovation EV-DO Diagnostic Port (COMxx), Novatel Wireless Ovation EV-DO GPS Port (COMxx) and Novatel Wireless Ovation EV-DO Status Port (COMxx)items. Leave the Device Manager open as you will find there the COM port numbers needed in the next steps.


8. In the Device Manager click on Ports. Select the COM port number assigned to the Novatel Wireless Status Port item in the Trace Port field in the Device Configuration dialog. Leave the Modem Port field empty.




PANTECH UM175

1. Unzip the driver files (PANTECH UM175 USB drivers.zip) on your computer.

2. Plug in the data card.

3. Windows will automatically detect the new hardware.

4. Select Install the software automatically (Recommended), and click Next.

5. Select Include this location in the search and browse for the folder where the driver files are located (e.g., C:\Pantech UM175). Click Next.

Pantech UM175 109

6. The driver files are installed. Click Finish.

7. Next go to Device Manager. Under Modems you should see the PANTECH UM175 item, and under Ports the PANTECH UM175 Diagnostic Port item.

If you do not see the items mentioned above and instead there are three unknown devices under Others, the driver installation has failed. Right-click each unknown item, select Update Driver Software, and browse to the folder where you unzipped the driver files. After the update, the Pantech items should appear in the Device Manager.

8. Next, set up the dial-up connection manually. Follow instructions on page 7 (for XP) or 10 (for Win 7) then continue from step 9.


9. In the Pantech UM175 Modem Properties dialog, Security page, select No encryption allowed in the Data encryption field. Click OK to close the dialog.


11. In the Nemo Outdoor Device Configuration dialog, define the following settings (check the port numbers from the Device Manager) and click Apply:

Trace port: Select the COM port number assigned to PANTECH UM175 Diagnostic Port Modem port: Select the COM port number assigned to PANTECH UM175 Packet switched dial-up connection: Select the dial-up connection that you configured

manually, for example, Pantech UM175


Pantech UML290 111

PANTECH UML290

Do not plug in the device before installation!

1. Browse to folder D:\Drivers\Qualcomm LTE USB Modem on the Nemo Outdoor USB flash drive.

2. Run the VZAM_7.6.3.4_2642j_PantechLTE.exe file to start the installation wizard. If the Windows Security dialog appears, click Run.

3. The device drivers are installed first. After the device drivers are installed, the VZAccess Manager installation is started.

4. Click

Date post:	13-Oct-2015
Category:	Documents
Upload:	penta-max
View:	87 times
Download:	0 times

Dial-up Networking Setup Guide 7.20 Mar14

Documents