Digital TV MonitorMTM400A Data Sheet
Features & BenefitsMultilayer, multichannel, remote monitoring and measurement at RFand TS layers to DVB, ATSC, DCII, and ISDB-T/Tb standards withcontent-checking support for both MPEG-2 and H.264/AVCDisplays key RF monitoring parameters for DVB-T and DVB-S/S2interfaces to provide early indication of signal degradation before anypicture impairment is visible to the end customer (Note: In DVB-S2mode only Transport Stream inputs are supported)No additional analysis software is needed; all confidence and diagnosticanalysis is carried out from the MTM400A aloneWhen used in conjunction with the VQS1000 Video Quality Softwareapplication, provides reliable and sophisticated analysis algorithmsapplied to decoded MPEG-2 or H.264 video to identify stuck, black,macro blocking, and compression artifacts
ApplicationsContribution and Primary Distribution
Terrestrial DistributionCable Headend MonitoringDTH or Network Operator Satellite Uplink Monitoring
IPTV Ingest and Headend Monitoring
IntroductionThe MTM400A provides a complete solution for real-time transmissionmonitoring of MPEG Transport Streams over RF and ASI interfaces.Powerful confidence monitoring capability and deep diagnosticmeasurements are both combined into a single integrated solution. Thissupports Broadcasters, Cable, Satellite, and Telecommunication Operatorsto deliver superior QoS levels with reduced operational expenditure.Deployed at key network nodes, the MTM400A provides an intuitive andsimplified presentation of video quality and diagnostic information. Thissupports the delivery of superior Qualify of Service (QoS) levels in anincreasingly complex broadcast environment.When used together with VQNet™, facility and network-wide views allowengineers to sectionalize network problems.
Data Sheet
Product InformationCritical RF measurements; MER and EVM, constellation displays, RFlevels, channel power, SNR, BER, Phase Noise, and Impulse Response
Provides early indication of signal degradation before any pictureimpairment is visible to the end customerDVB-S2 interface includes 16 and 32APSK for contribution anddistribution applications
Video/Audio content checking for both MPEG-2 and H.264/AVCThumbnail decode and display of multiple channels, simultaneouslyprovides a visual check of content with encoding parameters availableto the user (such as codec type, profiles and levels, aspect ratio,program guide event information, etc.)Backhaul of actual video and/or audio allows content to be fed backto the central monitoring point to see and hear the content beingbroadcast (encrypted content can be routed to a STB for hardwaredecode)
PSI/SI/PSIP/ARIB SI analysis and repetition rate graphingAllows broadcasters to determine that the system and serviceinformation is present and correct in the Transport Stream
"Green Stream" learning modeAllows monitoring by exception and elimination of false alarms
Multiplex viewAllows an at-a-glance view of program utilization over an extendedperiod allowing the user to see if bandwidth spikes occurred
Unique 2-level alarmsUniquely provides advanced warning of impending problems to avoidcustomer complaints. Single-level alarming means the alert can onlybe generated. With 2-level alarms, separate warning and failurealarms are not possible
FlexVuPlus™Uniquely presents simplified presentation of video quality anddiagnostic information
Filtered logsAllows diagnostics to be performed at the TS, Program, or PID levelsto "zoom in" on problems quickly
Simultaneous connection of multiple remote users and Multi-sink SNMPtraps for Network Management Systems (NMS)
Provides early visibility of problems to key individuals throughout theorganization, supporting quicker notification and corrective actionAllows multiple users and/or NMS to access the MTM400Asimultaneously
FlexVuPlus™ configurable windows with DVB-S2 display.
Video and audio content monitoring to ensure QoE is maintained.
2 www.tektronix.com
Digital TV Monitor — MTM400A
MTM400A Diagnostic Analysis Software OptionTrigger recording to be captured and rapidly analyzed in greater depthusing powerful offline analysis tools such as the Tektronix MTS4SAsoftwareException monitoring with simple, automated template generation fromreference streams. Template testing checks a number of key parametersto ensure the Transport Stream has been constructed as intended.These parameters include the Transport Stream ID and Network ID, thenumber of programs in the multiplex, that each program has all of itscomponents (Video, Audio, Data, Teletext, Subtitles) and ConditionalAccess (CA) statusAdvanced Timing Analysis including unique PTS-PCR graphs forreal-time buffer measurements. This provides indication of encoding andmultiplexing errors and in-depth PCR analysis; the resulting graphicalviews enable timing and jitter measurements to ensure correct operationof the networkBit rate testing determines whether PIDs, programs, services, oruser-defined groups of PIDs are within user-definable limits, ensuringcorrect multiplex operation. Tektronix proprietary PID variability testgives indication of PID bit rate variation to assess effects of statisticalmultiplexingComprehensive service logging enables verification of service levelagreements to ensure contractual obligations are metThe channel polling capability for the MTM400A, combined with RFinterfaces, allows up to 200 RF channels to be monitored in a repeatingcyclical measurement process. Control and configuration of the pollingis undertaken using flexible XML scripting. This polling ability makes asingle MTM400A a broader tool, monitoring large numbers of networkpoints in a time-sampled measurement mode
Advanced Timing Analysis including PTS-PCR for real-time buffer measurements to giveindication of encoding and multiplexing errors.
www.tektronix.com 3
Data Sheet
Technical OverviewSCTE-142 and A/78 monitoring modes classify five distinct levels ofimportance
Transport Stream Off Air (TOA), Program Off Air (POA), ComponentMissing (CM), Quality of Service (QoS), Technically Nonconformant(TNC)Enables filtering and display only of errors that require immediateattention
Comprehensive TR 101 290 Priority 1, 2, and 3 MPEG measurementsProvides in-depth analysis of Transport Stream, syntax, timing, andcontent to support root-cause analysis of system errors
Superior PCR measurements (PCR_OJ, DR, and FO)PCR_OJ enable deterministic measurements on Transport Streamand network induced jitter allowing such errors to be isolatedDR and FO measurements allow diagnosis of longer-term systemdegradation
PSI/SI/PSIP/DC-II conformance and consistency checkingClosed Caption (EIA608/708 and SCTE20/21) and Regional RatingsDescriptor (RRT) check ensures conformance to regulationsSI/PSI/PSIP testing ensures set-top box performance (channelchange, EPG, etc.) can be verified
SCTE 35 DPI monitoringAllows analysis and diagnostics of "splice" advertising and other localcontent
SCTE-142 and A/78 modes classify five distinct levels of importance.
EPG View
4 www.tektronix.com
Digital TV Monitor — MTM400A
CharacteristicsPower RequirementsCharacteristic DescriptionPower Consumption(Nominal)
40 VA
Voltage 100 to 240 VFrequency 50/60 Hz
MonitoringCharacteristic DescriptionData Rate
Maximum data rate 155 Mb/s*1
Minimum data rate 250 Kb/s*1 Maximum Transport Stream bit rate is dependent on Transport Stream content and depth of analysis being
performed. Depth of stream analysis is handled gracefully if SI/PSIP maximum content is exceeded toensure critical measurements continue to be performed.
ATSC A/78A and SCTE142 Error ClassificationsClassification DescriptionTOA Transport Stream Off AirPOA Program Off AirCM Component MissingQoS Quality of ServiceTNC Technically Nonconforming
TR 101 290 Tests and Measurements1st Priority
Measurements2nd Priority
Measurements3rd Priority
Measurements1.1 Ts_sync_loss 2.1 Transport error 3.1a NIT_actual_error
1.2 Sync_byte_error 2.2 CRC_error 3.1b NIT_other_error1.3a PAT_error_2 2.3a PCR_repetition_error 3.2 SI repetition error
1.4 Continuity_count_error 2.3b PCR_discontinuity_indicator_error
3.4a Unreferenced PID
1.5a PMT_error_2 2.4 PCR_accuracy_error 3.5a SDT_actual_error1.6 PID_error 2.5 PTS_error 3.5b SDT_other_error
2.6 CAT_error 3.6a EIT_actual_error3.6b EIT_other_error3.6c EIT_PF_error
3.7 RST_error3.8 TDT_error
DVB-S2 Interface Characteristics (Option S2)Characteristic DescriptionInput FrequencyRange
950 MHz to 2150 MHz with 1 MHz step size
Input Signal AmplitudeRange
–60 dBm to –30 dBm for a CBER of <1e–6
Modulation Format QPSK in accordance with DVB-S (ETSI EN 300 421)QPSK, 8PSK, 16APSK, and 32APSK in accordancewith DVB-S2 (ETSI EN 302 307) including Constant andVariable Coding and Modulation (CCM and VCM)
Modulated Baud Rate 1 MBaud min, 60 MBaud maxCode Rate DVB-S: 1/2, 2/3, 3/4, 5/6, 6/7, 7/8
DVB-S2: 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10FEC Modes Viterbi and Reed-solomon in accordance with DVB-S
LDPC and BCH in accordance with DVB-S2Short and Normal FEC blocks in accordance with DVB-S2
Roll Off 0.2, 0.25, 0.35Connector Style F-styleInput TerminationImpedance
75 Ω nominal
Input Return Loss >6 dB min, 950 MHz to 2150 MHzLNB Supply Voltage Selectable; 13.0 V ±1.5 V or 18.0 V ±1.5 V, with 100 Ω,
5 W resistor loadLNB Supply MaximumCurrent
200 mA max
LNB 22 kHz SignalingFrequency
17.6 kHz min, 26.4 kHz max (22 kHz ±20%)
LNB 22 kHz SignalingAmplitude
600 mVp-p with 100 Ω load
LNB Mode DiSEqC 2Ultimate ModulationError Ratio
30 dB with Equalizer
DVB-S2 Measurement Characteristics (Option S2)Characteristic DescriptionRF Lock RF lock indicated to the user by LED and Status on UIInput Level(Signal Strength)
Range: –60 dBm to –30 dBmResolution: 1 dBmAccuracy: ±5 dBm
EVM (Error VectorMagnitude)
Display Range: ≤4.0% to ≥30.0% RMSResolution: 0.1%Accuracy: ±20% of reading
MER (Modulation ErrorRatio) with Equalizer
Display Range: 10 to 30 dB with EqualizerResolution: 1 dBAccuracy: ±2 dB for range 10 to 20 dB
CNR (Carrier to NoiseRatio)
Display Range: 10 to 30 dBResolution: 1 dBAccuracy: ±2 dB for range from 10 to 28 dB
Phase Noise Display Range: 5 to 45° RMSResolution: 1°
Pre Viterbi BER Pre-Viterbi BER displayedPre Reed Solomon(RS) BER
Pre-RS BER displayed
Pre LDPC BER Pre-LDPC BER displayedPre BCH BER Pre-BCH BER displayedPost RS BER and TEF(Transport Error Flag)
Post Reed Solomon BER (TEF ratio), TEF rate andnumber of Transport Error Flags (TEF count) displayedto the user
TransmissionParameters
All Coding and Modulation parameters are indicated to theuser in the UI. Transport Stream monitor must be tuned toa valid Transport Stream in order to report RF transmissionparameters
Constellation The RF constellation displayed on the UI
www.tektronix.com 5
Data Sheet
COFDM Interface Characteristics (Option CF)Characteristic DescriptionInput FrequencyRange
50 MHz to 858 MHz with 166.7 or 62.5 kHz step size
Tuning Accuracy Better than ±50 ppm typicalChannel Bandwidth 6 MHz, 7 MHz and 8 MHz (SW selectable)Connector Style F-type with BNC adaptorInput TerminationImpedance
75 Ω nominal
Input Return Loss 7 dB typical 50 MHz to 858 MHzRx Lock Status Indicated by LED on rear panel and by the UIModulation SchemeSupported
QPSK (4QAM), 16QAM, and 64QAM modulation
Transmission Modes 2K carriers and 8K carriersHierarchical Modes All hierarchies are be supported, including no hierarchy,
and alpha = 1, 2, and 4Viterbi Puncture Rates 1/2, 2/3, 3/4, 5/6, 7/8Guard Interval 1/32, 1/16, 1/8, 1/4Spectrum Polarity The receiver will operate with both inverted and normal
spectral polarityInput Signal AmplitudeRange
QPSK (4QAM): –85 dBm to –10 dBm (24 dBuV to99 dBuV) typical16QAM: –80 dBm to –10 dBm (29 dBuV to 99 dBuV)typical64QAM: –72 dBm to –15 dBm (37 dBuV to 94 dBuV)typical
COFDMMeasurement Characteristics (Option CF)Characteristic DescriptionCarrier Offset Carrier offset is measured from the tuned channel frequency
to a accuracy of ±10 ppm typicalThis includes the ability to set alarms and produce trendgraphs over a seven-day period including min, max, andaverageDisplay Range Resolution Accuracy
SNR (Signal toNoise Ratio)
6 dB to 40 dB forQPSK (4QAM)11 dB to 40 dB
for 16QAM16 dB to 40 dB
for 64QAM
1 dB ±1 dB to 30 dBSNR (measuredat –30 dBm inhigh-resolutionmode) typical
EVM (Error VectorMagnitude)
1% to 30% RMS,for QPSK
1% to 20% RMS,16QAM
1% to 8.5% RMS,64QAM
0.1% —
MER (ModulationError Ratio) withEqualizerBoth MER Peakand MER Averageare displayed asmeasured acrossall carriers
6 dB to 37 dB forQPSK (4QAM)11 dB to 37 dB
for 16QAM16 dB to 37 dB
for 64QAM
0.1 dB ±1 dB to 30 dB(measured at–30 dBm in
high-resolutionmode) typical
This includes the ability to set alarms and produce trend graphs over a seven-dayperiod including min, max, and averageConstellation The RF constellation is displayed on the UIChannel ImpulseResponse
Display of channel impulse response
Channel SpectralResponse
Active receive channel spectrum, RF level vs. frequency
BER (Bit ErrorRatio)
Pre FEC, BER, and Error Sec BER values are displayed. Thisincludes the ability to set alarms and produce trend graphsover a seven-day period including min, max, and average
Post ReedSolomon BER
Post RS BER (Uncorrectable Error Count) displayed. Thisincludes the ability to set alarms and produce trend graphsover a seven-day period including min, max, and average
TEF (TransportError Flag)
Alarm generated on detection of a TEF
6 www.tektronix.com
Digital TV Monitor — MTM400A
Turbo 8PSK Interface Characteristics (Option EP)Interface Option EP provides both QPSK (L-band) and Turbo 8PSK interface andmeasurement capability. For non-Turbo code modulation formats the Option S2card is recommended.Characteristic DescriptionInput FrequencyRange
950 MHz to 2150 MHz with 100 kHz step size
Modulation Format Turbo 8PSK*2
Modulated Baud Rate 1 MBaud min, 30 MBaud maxTurbo Viterbi ValuesSupported
2/3, 3/4 (2.05), 3/4 (2.1), 5/6, 8/9
Turbo FEC Turbo CodeConnector Style F-styleInput TerminationImpedance
75 Ω nominal
LNB Supply Voltage Selectable; 13.0 V ±1.5 V or 18.0 V ±1.5 VLNB Supply MaximumCurrent
200 mA max
LNB 22 kHz SignalingFrequency
17.6 kHz min, 26.4 kHz max (22 kHz ±20%)
LNB 22 kHz SignalingAmplitude
600 mVp-p with 100 Ω load
Modes Supported Turbo 8PSK*2 Please note that the Turbo 8PSK option does not support nonturbo 8PSK (DVB-DSNG), or DVB-S2. For
DVB-S2 please use DVB-S/S2 interface card (Option S2).
Turbo 8PSKMeasurement Characteristics (Option EP)RF MeasurementsCharacteristic DescriptionRF Lock RF lock is indicated to the user by an LED on the rear panel and
a status icon on the UIRange Display
RangeResolution Accuracy
Input Level(SignalStrength)
–60 dBm to–30 dBm
— 1 dBm ±5 dBm typical
EVM (ErrorVectorMagnitude)
— ≤4.0% to≥30.0% RMS
0.1% —
MER(ModulationError Ratio) withEqualizer
— 10 to 26 dBwith Equalizer
1 dB ±2 dB typicalfor range 10
to 20 dB
SNR (Signal toNoise Ratio)
— 5 to 35 dB 1 dB ±2 dB typicalfor range from
5 to 30 dBThis includes the ability to set alarms and produce trend graphs over a seven-dayperiod including min, max, and averagePre ReedSolomon (RS)BER
Pre-RS BER is displayed on the UI
Post RS BERand TEF(Transport ErrorFlag)
Post Reed Solomon BER (TEF ratio), TEF rate, and number ofTransport Error Flags (TEF count) are displayed on the UI
Constellation The RF constellation is displayed on the UI
EnvironmentalCharacteristic DescriptionTemperature
Operating +5 °C to +40 °CNonoperating –10 °C to +60 °C
HumidityOperating Maximum relative humidity 80% for temperatures up to
31 °C decreasing linearly to 50% relative humidity at 40 °CNonoperating 10% to 95% relative humidity, noncondensing
AltitudeOperating 0 m to 3000 m (9800 ft.)Nonoperating 0 m to 12000 m (40000 ft.)
Random VibrationOperating 5 to 500 Hz, GRMS = 2.28Nonoperating .5 to 500 Hz, GRMS = 0.27
Functional ShockOperating 30 G, half sine, 11 ms duration
Electromagnetic CompatibilityEC Declaration ofConformity
Meets EN55103. Electromagnetic environment E4
Australia / NewZealand Declarationof Conformity
Meets AS/NZS 2064
FCC Emissions are within FCC CFR 47, Part 15, Subpart B,Class A limits
Safety Meets 73/23/EEC, EN61010-1, UL3111-1 and CAN/CSA22.2 No. 1010.1-92, IEC61010-1
Physical CharacteristicsDimension mm in.Height 44 1.73Width 430 17.13Depth 600 23.62Weight*3 kg lb.Net 6.0 13.3Shipping 9.0 19.7Required Clearance mm in.Top 0 0Bottom 0 0Left side Standard 19 in. rackmountRight side Standard 19 in. rackmountFront Clearance for handles requiredRear Clearance for connectors required*3 Weight does not include optional interface cards.
www.tektronix.com 7
Data Sheet
Ordering InformationMTM400ADigital DTV Monitor.Includes: 1RU chassis fitted with Transport Stream processor card, manual, rackslides, power cord, and license key certificate.
OptionsOption DescriptionOpt. CF COFDM InterfaceOpt. DIAG Deep-dive MPEG diagnostic analysis
Includes:Triggered recording capability up to 160 MBTemplate testing (for user-defined service plan testing)In-depth PCR analysis with graphical result viewsBit rate testing functionalityService loggingRF polling functionality
Opt. EP Turbo 8PSK/QPSK InterfaceOpt. S2 DVB-S/S2 Interface
Language OptionsOption DescriptionOpt. L0 English User GuideOpt. L5 Japanese User Guide
Service OptionsOption DescriptionOpt. G3 Complete Care 3 Years (includes loaner, scheduled
calibration and more)Opt. G5 Complete Care 5 Years (includes loaner, scheduled
calibration and more)Opt. R3 Repair Service 3 Years (including warranty)Opt. R5 Repair Service 5 Years (including warranty)
Power ConnectionsOption DescriptionOpt. A0 North America power plugOpt. A1 Universal EURO power plugOpt. A2 United Kingdom power plugOpt. A3 Australia power plugOpt. A4 240 V North America power plugOpt. A5 Switzerland power plugOpt. A6 Japan power plugOpt. A10 China power plugOpt. A99 No power cord or AC adapter
Complementary ProductsOption DescriptionMTS4SA Opt. TSCL Stand-alone Deferred Time Software package.
DVB/ATSC/ARIB TS Compliance Analyzer Software (TSfile size limited to 192 MB). For full details see separatedata sheet
VQNet Video Service Assurance Management Software forinstallation on customers own PC. For full details seeseparate data sheet
VQS1000 Video Quality Software application for single-ended QoEanalysis of video and audio content
Field Upgrade KitsOption DescriptionField Upgrade Kit to Add:MTM4UP Opt. CF Adds COFDM InterfaceMTM4UP Opt. DIAG Deep-dive MPEG diagnostic analysisMTM4UP Opt. EP Adds 8PSK/QPSK InterfaceMTM4UP Opt. GE Adds GbE IP Video Monitoring InterfaceMTM4UP Opt. LX 1000BASE-LX Long Wavelength Optical Port with LC
connector (Single Mode 1310 nm)MTM4UP Opt. QA Adds QAM Annex A Interface to an existing probeMTM4UP Opt. QB2 Adds QAM Annex B InterfaceMTM4UP Opt. QC Adds QAM Annex C Interface to an existing probeMTM4UP Opt. SX 1000BASE-SX Short Wavelength Optical Port with LC
connector (Multi Mode 850 nm)MTM4UP Opt. S2 Adds DVB-S/S2 InterfaceMTM4UP Opt. VS Adds 8VSB InterfaceMTM4UP Opt. ZX 1000BASE-ZX Optical Port with LC connector (Single
Mode 1550 nm) (requires Opt. GE)MTM4UP Opt. 01 Adds triggered recording capability up to 160 MBMTM4UP Opt. 02 Adds Transport Stream service information analysis
(PSI/SI/PSIP/ARIB view)MTM4UP Opt. 03 Adds template testing (for user-defined service plan
testing)MTM4UP Opt. 04 Adds in-depth PCR analysis with graphical result viewsMTM4UP Opt. 05 Adds bit rate testing functionalityMTM4UP Opt. 06 Adds service loggingMTM4UP Opt. 07 Adds IP/RF polling functionalityOtherMTM4UP Opt. IFC One-time install of all selected options and calibration for
one product
Product(s) are manufactured in ISO registered facilities.
8 www.tektronix.com
Digital TV Monitor — MTM400A
www.tektronix.com 9
Data Sheet
10 www.tektronix.com
Digital TV Monitor — MTM400A
www.tektronix.com 11
Data Sheet Contact Tektronix:ASEAN / Australasia (65) 6356 3900
Austria 00800 2255 4835*
Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777
Belgium 00800 2255 4835*
Brazil +55 (11) 3759 7627
Canada 1 800 833 9200
Central East Europe and the Baltics +41 52 675 3777
Central Europe & Greece +41 52 675 3777
Denmark +45 80 88 1401
Finland +41 52 675 3777
France 00800 2255 4835*
Germany 00800 2255 4835*
Hong Kong 400 820 5835
India 000 800 650 1835
Italy 00800 2255 4835*
Japan 81 (3) 6714 3010
Luxembourg +41 52 675 3777
Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90
Middle East, Asia, and North Africa +41 52 675 3777
The Netherlands 00800 2255 4835*
Norway 800 16098
People’s Republic of China 400 820 5835
Poland +41 52 675 3777
Portugal 80 08 12370
Republic of Korea 001 800 8255 2835
Russia & CIS +7 (495) 7484900
South Africa +41 52 675 3777
Spain 00800 2255 4835*
Sweden 00800 2255 4835*
Switzerland 00800 2255 4835*
Taiwan 886 (2) 2722 9622
United Kingdom & Ireland 00800 2255 4835*
USA 1 800 833 9200
* European toll-free number. If not accessible, call: +41 52 675 3777
Updated 10 February 2011
For Further Information. Tektronix maintains a comprehensive, constantly expandingcollection of application notes, technical briefs and other resources to help engineers workingon the cutting edge of technology. Please visit www.tektronix.com
Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents,issued and pending. Information in this publication supersedes that in all previously published material.Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks ofTektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarksof their respective companies.
09 Jun 2011 2AW-21525-10
www.tektronix.com