www.dimex.in 3

Dimex Provides you the BEST Quality & Energy E�cient uPVC Profile Window & Doors

“ ”

www.dimex.in 5

he corner welding testing is very important for the strength and long life of a uPVC TWindow. To pass this test, it is possible only for those companies who use the right Formulation & Right Wall Thickness of the extruded profiles.

The cheaper profile companies who are using over 20-30% Calcium Carbonate normally do not pass this test.

The quality of a uPVC window can be determined by the quality of following Four main components:

The uPVC Profile: The uPVC Profile is basically an extruded section of a mixture of PVC with certain additives to make it suitable for making uPVC Windows and Doors. So, this very formulation technology is the key to make a Quality profile to make the Premium Windows. This formulation varies according to the climates. That’s why the formulation for High UV Sensitive India requires a formulation combination of :

2.5 mm. wall thickness & 8 Parts of

Titanium Dioxide. (The success story of DIMEX)

www.dimex.in 4

“In Fusion Welding - Joint should never come apart”

Organizer:

www.dimex.in 7

High UV Protected

www.dimex.in 9

2 Track, 3 Track with or without mesh

www.dimex.in 11

Openable windows & Doors with optimum insulation

www.dimex.in 13

www.dimex.in 15

www.dimex.in 17

“HARDWARE is the SOUL of the WINDOW”

www.dimex.in 19

www.dimex.in 21

WHY ARE FRAMES REINFORCED?The purpose of reinforcing uPVC window and door frames is to control the rate of expansion and to provide rigidity to frame sections over a certain size. It is also used to provide rigidity for hardware, particularly where door locking mechanisms are fitted.

Reinforcing can be specified in exposed and coastal areas where wind loading on larger frames is a consideration.

However, there is a case for fully reinforcing uPVC frames. All foiled (wood grain) products are fully reinforced as standard. The reason for this is to provide an enhanced control of the rate of expansion for these products. The dark finish and the coloured uPVC

extrusions absorb heat far more than white extrusions and can deform if not controlled by reinforcing. All of DIMEX foiled and wood grain products are fully reinforced automatically as well as all uPVC door products.

WHAT ARE uPVC WINDOW AND DOOR FRAMES REINFORCED WITH?uPVC windows and uPVC door frames are reinforced with either aluminium or galvanised steel. The choice is the preference of the fabricator and there is a small cost di�erential too. Aluminium is slightly more expensive but it is easier to work with and doesn't add

too much weight to the products whereas steel is heavier but cheaper. The actual shape is no more than an "L" or "U" section of thin steel or aluminium and does not go the full length of the profile; it stops several centimetres short so as not to foul or interfere with

the welding process and where there are mullion or transom joints, the reinforcing is fitted in pieces and is not normally inserted as a full length. Therefore reinforcement is not suitable for structural support put purely for the reasons outlined above.

For bay poles, bay posts and structural mullions, a thicker section is used. This is to provide strength and rigidity where frames are to be

joined together and to provide a strong fixing ground. Bay poles and posts can be used in a structural situation and jacking plates are

available if required.

CONCLUSIONYou can be assured that if you buy your frames from DIMEX Window, you will always be supplied with the correct reinforcement suitable for your requirements.

www.dimex.in 23

www.dimex.in 25

www.dimex.in 27

MADE TO MEASURE...

www.dimex.in 31

DIMEX is hard to BEAT

www.dimex.in 33

Dimex Authorized Fabricator

Dear Customer,

So that the DIMEX Quality is brought to you in any part of Indiaour DIMEX’s Qualified and authorized Fabricator is near to you.

DIMEX’s whole concept of profile extrusion and window making is that together we are Eco-Friendly so : -- Eco-friendly production - Against Harsh Weather - Servicing made Easy - Residues are minimum due to our cutting optimization and separating the Residues and whatever is to be recycle is Recycled for further uses. - The hardware is rust free.