DISHWASHER - Indesit Company -...

Merloni

Elettrodomestici

Technical Fitting Manual

DISHWASHER

GB 99-11-02/01 1-26Language Issue/Edition Page

Merloni

Elettrodomestici

Index

1 CONFORMITY OF APPLIANCE 3

2 DIMENSIONS OF DISHWASHER AND HOUSING SPACE 3

2.1 Standard equipment - Fitting tools 4

3 FITTING THE FRONT PANEL 5

3.1 Technical information for installation - adjusting the front panel (fitted dishwasher) 5

3.2 Using the drilling template 6

3.3 Fastening the brackets to the wooden door 8

3.4 Fitting the wooden door to the dishwasher 10

3.5 Adjusting the door springs 13

3.6 Fitting the wooden door to the dishwasher before installing with the client 14

3.7 Adjusting the feet 15

3.8 Fastening to the worktop (wooden worktop only) 16

4 FITTING THE MOPBOARD 17

5 PLUMBING IN 21

5.1 Connecting to the water supply 21

5.2 Connecting to the drainage system 23

6 CONNECTION TO THE MAINS 23

CAUTIONS AND ADVICE 24

N.B. All measurements are expressed in millimetres (mm).

DISHWASHERTechnical Fitting Manual


Merloni

Elettrodomestici

1 CONFORMITY OF APPLIANCE

This appliance complies with the following EC Directives:

• 73/23/EEC dated 19/02/73 (Low voltages) and subsequent amendments

• 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequentamendments

2 DIMENSIONS OF DISHWASHER AND HOUSING SPACE

Fig. 1

The housing space, as well as having the dimensions indicated in Fig. 1, mustobviously allow the electric cable and the water supply and drainage pipes topass (see chapter 6).

820

570

595 (445)

49

131

170

610

598 (445)

100

450600

820-

870 570



Merloni

Elettrodomestici

2.1 Standard equipment - Fitting tools

The appliance comes complete with a folder containing assembly instructions(it also contains the drilling template used to fit the wooden door; which mustobviously be cut out before use).

As can be seen from the figure, the appliance is also fitted with the following:

Fig. 2

• Nº 2 Door fairing screw covers (item D)

• Nº 2 Door fastening brackets (item B)

• Nº 6 Screws fastening brackets to door (item A)

• Nº 4 Solid wood fastening screws (item A1); there are Nº 2 of these in thefitted version

• Nº 2 Connection blocks (item F) for totally hidden version only

• Nº 2 Fitting slides (item C)

To install the appliance correctly, the following tools are required:

• Size 13 mm setscrew wrench

• Size 4 mm hexagonal setscrew wrench (item E)

• Cross-cut screwdriver

• Drill with 2 mm

• Size 4 mm Allen wrench

A (Ø 4X16) C

E4 mm. 13 mm.

D

A1 (Ø 4X25)

E

B B

F



Merloni

Elettrodomestici

3 FITTING THE FRONT PANEL

3.1 Technical information for installation - adjusting the front panel (fitted dishwasher)

In the fitted version, the front control panel can easily be aligned with thedrawers of the kitchen units, using the strips provided with the appliance (SeeFig. 3 and Fig. 4).

The height of the front control panel is 115 mm. There are 3 strips provided,and each one increases the height by 7.5 mm (if necessary it is possible to fitup to 5 of these strips).

Fig. 3 Fig. 4

137,

5

115



Merloni

Elettrodomestici

3.2 Using the drilling template

When preparing the dishwasher for insertion in the kitchen units, under nocircumstances drill holes in the side walls and door of the appliance, as thismight cause it to malfunction. Before carrying out operations that requireaccess to internal components, always disconnect the dishwasher from thepower supply.

The maximum dimensions (and weight) of the wooden panels to be fitted tothe dishwasher are as follows:

The height of 610 mm, for the fitted dishwasher, must be decreased if theheight of the front panel is increased using the compensation strips. It may benecessary to trim the mopboard, should this prevent the door from openingcompletely.

To fasten the panel to the dishwasher door, bring the top edge of the template(obtained by cutting out the shape marked in the folder supplied with theappliance) (indicated by arrow A in Fig. 5 for totally hidden dishwashers inFig. 6 for fitted dishwashers) up to the top edge of the panel. Both sides of thetemplate (at top and bottom) are marked with a number of positions,corresponding to the various panel widths available.

Align the template with the right or left hand side of the panel, so that thelatter coincides with the measurement required. Trace the position of screwsby inserting the tip of a drill or a pencil into the three holes closes to the sidein question (indicated by arrow B in Fig. 5 for totally hidden dishwashers inFig. 6 for fitted dishwashers).

Repeat the above operation on the opposite side, using the corresponding sideof the template.

60 cm 45 cm

Height (fitted) 610 610Height (totally hidden) 725 725Width 598 448Thickness 20 20Weight 2 – 10 Kg 0 – 7.5 Kg



Merloni

Elettrodomestici

Fig. 5

Fig. 6

432 mm.(45 cm.) 582 mm.(60 cm.)

436 mm.(45 cm.) 586 mm.(60 cm.)

440 mm.(45 cm.) 590 mm.(60 cm.)

444 mm.(45 cm.) 594 mm.(60 cm.)

448 mm.(45 cm.) 598 mm.(60 cm.)

432 mm.(45 cm.) 582 mm.(60 cm.)

436 mm.(45 cm.) 586 mm.(60 cm.)

440 mm.(45 cm.) 590 mm.(60 cm.)

444 mm.(45 cm.) 594 mm.(60 cm.)

448 mm.(45 cm.) 598 mm.(60 cm.)

28 2819 19

15

30

432

mm

.(45

cm.)

432

mm

.(45

cm.)

582

mm

.(60

cm.)

582

mm

.(60

cm.)

436

mm

.(45

cm.)

436

mm

.(45

cm.)

586

mm

.(60

cm.)

586

mm

.(60

cm.)

440

mm

.(45

cm.)

440

mm

.(45

cm.)

590

mm

.(60

cm.)

590

mm

.(60

cm.)

444

mm

.(45

cm.)

444

mm

.(45

cm.)

594

mm

.(60

cm.)

594

mm

.(60

cm.)

448

mm

.(45

cm.)

448

mm

.(45

cm.)

598

mm

.(60

cm.)

598

mm

.(60

cm.)

432

mm

.(45

cm.)

432

mm

.(45

cm.)

582

mm

.(60

cm.)

582

mm

.(60

cm.)

436

mm

.(45

cm.)

436

mm

.(45

cm.)

586

mm

.(60

cm.)

586

mm

.(60

cm.)

440

mm

.(45

cm.)

440

mm

.(45

cm.)

590

mm

.(60

cm.)

590

mm

.(60

cm.)

444

mm

.(45

cm.)

444

mm

.(45

cm.)

594

mm

.(60

cm.)

594

mm

.(60

cm.)

448

mm

.(45

cm.)

448

mm

.(45

cm.)

598

mm

.(60

cm.)

598

mm

.(60

cm.)

29

2929

432

mm

.(45

cm.)

432

mm

.(45

cm.)

582

mm

.(60

cm.)

582

mm

.(60

cm.)

436

mm

.(45

cm.)

586

mm

.(60

cm.)

586

mm

.(60

cm.)

440

mm

.(45

cm.)

440

mm

.(45

cm.)

590

mm

.(60

cm.)

444

mm

.(45

cm.)

444

mm

.(45

cm.)

594

mm

.(60

cm.)

594

mm

.(60

cm.)

448

mm

.(45

cm.)

448

mm

.(45

cm.)

598

mm

.(60

cm.)

598

mm

.(60

cm.)

432

mm

.(45

cm.)

432

mm

.(45

cm.)

582

mm

.(60

cm.)

582

mm

.(60

cm.)

436

mm

.(45

cm.)

436

mm

.(45

cm.)

586

mm

.(60

cm.)

586

mm

.(60

cm.)

440

mm

.(45

cm.)

440

mm

.(45

cm.)

590

mm

.(60

cm.)

590

mm

.(60

cm.)

444

mm

.(45

cm.)

444

mm

.(45

cm.)

594

mm

.(60

cm.)

448

mm

.(45

cm.)

448

mm

.(45

cm.)

598

mm

.(60

cm.)

598

mm

.(60

cm.)

2929

29

A

B

B

115122,5130137,5145152,5

mm

582586590594

=598

=598594590586582

A

B

B



Merloni

Elettrodomestici



3.3 Fastening the brackets to the wooden door

Drill holes with a diameter of 2 mm at the positions marked. In the case ofchipboard panels, only drill the surface coat, whereas in solid wood panels theholes can be drilled deeper. Position the two brackets on the holes drilled at thebottom of the panel. The brackets must be fastened to each side, using theoutermost holes; the fins must face downwards. The connection blocks (in thetotally hidden dishwasher) must be screwed into the two top holes (Fig. 7).

Fig. 7 Fig. 8

Fig. 9

A

B

Merloni

Elettrodomestici

Fig. 11

Fig. 10

A

BF

A1



Merloni

Elettrodomestici

3.4 Fitting the wooden door to the dishwasher

In the case of a fitted dishwasher, insert the metal fins on the bracket into theslots on the dishwasher door, moving it to the right to connect (Fig. 12).

Fig. 13

In the case of totally hidden dishwashers, insert the top connection blocks inthe special housings formed in the appliance’s front panel, then push thepanel upwards until it locks.

Fig. 12

1

1

2

2

33

1

2



Merloni

Elettrodomestici

Accompany the panel downwards again, simultaneously bringing the bottomof the panel up against the dishwasher door, so that the fins on the bracketsenter the housings provided (Fig. 14).

In both cases open the dishwasher door (the panel will support itself) andalign the solid wood with the door, bringing it into contact with the frontpanel. Remove the plastic plugs covering the holes inside the dishwasher andlock the panel in place using the screws provided (Fig. 15). Remember toclose the two holes with the plastic plugs removed as above.

Fig. 15

Fig. 14

3

3

1

1

22



Merloni

Elettrodomestici

Fig. 16

Fig. 17

Fig. 18

N.B. Pay attention to the thickness of the panel, as over-long screws might come through at the oth-er side when fastening.

A

D

A1(Ø 4X25)15-20 mm.



Merloni

Elettrodomestici

3.5 Adjusting the door springs

The door must, obviously, be perfectly balanced, that is to say it must be adjustedso that it remains stationary in whatever position it is opened to.

On delivery the spring tension is adjusted to guarantee a perfect balance withlightweight wooden panels. Balance can be achieved for heavier, solid woodpanels merely by turning the screws located at the top of the appliance in aclockwise direction, making sure both screws are turned by the same amount,as shown in the figure. To do this, use a size 4 mm Allen wrench.

Fig. 19

Fig. 20

+ +

+

Kg.



Merloni

Elettrodomestici

3.6 Fitting the wooden door to the dishwasher before installing with the client

Should it be necessary to transport the appliance to its final destination after havingfitted the wooden panel and made any adjustments to the height of the front panel(fitted dishwasher), we recommend that the original packing be used. For thisreason the packing has been designed to allow the above operations to be carriedout without having to unpack the product completely.

It is recommended that you proceed in sequence, as indicated in Fig. 21 from 1 to 6.

1. Using a knife, cut the door side of the packing along the pre-cut marks on thethree sides (1)

2. Lift up the door side of the packing, cut off the front corner elements and dis-card them (2)

3. Assemble the wooden door (3) (4)

4. Return the door side of the packing to its original position (5)

5. Seal the cuts with adhesive tape (6)

Fig. 21

1 2 3

4 5 6



Merloni Elettrodomestici

3.7 Adjusting the feet

Fit the appliance into the space provided and then adjust the rear height byturning the three size 4 mm setscrews located at the bottom front (in themodels with this option); turn the screws clockwise to raise the appliance andanticlockwise to lower it.Level the appliance at the front using a size 13 mm setscrew wrench.

Fig. 22

Fig. 23

Fig. 24

N.B. Do not use electric screwdrivers when adjusting the back feet.

N.B. Always use the slides provided with the appliance, to avoid damaging the floor.

E

C




3.8 Fastening to the worktop (wooden worktop only)

Once the appliance has been fitted and all adjustments have been made, theappliance itself can be made more stable by fastening it to the worktop withtwo wood screws, as illustrated in the photo.

Fig. 25




4 FITTING THE MOPBOARD

Position the dishwasher in the fitting space. Carry out the following operations:

1. Fit the continuous mopboard as indicated by the manufacturer of thekitchen units

2. Open the dishwasher door slowly to check whether the panel fitted to itbangs against the mopboard

3. If so, it will be necessary to trim the mopboard

The height required for the mopboard in the area in which the door opens(“y”) can be calculated using the following table.

Fig. 26

Fig. 27

More specifically, after inserting the two heights “a” and “b”, read across thevalues in the table to find the height “y”. Eliminate any excess mopboard.

4. Waterproof the cut surface with varnish

a

b

09 001 011 021 031 041 051 061 071

04 87 78 69 501 411 221 921 631 141

05 97 88 79 601 511 321 131 731 241

06 08 09 99 801 711 621 431 141 641

07 38 39 201 211 121 131 931 741 451

08 78 79 701 711 721 831 841 851 961

09 09 001 011 021 031 041 051 061 071

001 09 001 011 021 031 041 051 061 071

b (

mm

)

a (mm)

y

y




5. Re-fit the continuous mopboard

Fig. 28

If the dishwasher is to be fitted at the end of a composition, a kit is available(Spare Parts Code 059638) to enable the mopboard to be fitted to theappliance. To do this, position the brackets on the mopboard

Fig. 29

y




and use the slots provided on the front panel of the appliance.

Fig. 30

Insert the brackets with the mopboard. Then lock the metal brackets using thesquare element and screw.

Fig. 31

N.B. To show the various items more clearly, the mopboard is not illustrated in the figure, but onlythe brackets.




Insert the dishwasher into the space and align the mopboard with the rest ofthe composition.

Fig. 32

Alignment is achieved by pressing on the mopboard, as the “L” shaped strutsprevent the brackets from sliding by pressing against them.




5 PLUMBING IN

5.1 Connecting to the water supply

5.1.1 Connecting to the cold water tap

Connect the supply pipe to a cold water tap with a 3/4" threaded mouth,taking care to fasten it tightly to the tap and inserting the filter elementcorrectly (Fig. 33).

In models fitted with a supply pipe with WATERSTOP device the filter elementis already fitted in the threaded mouth.

If the water supply pipe is new, or has not been used for some time, run thewater through it before connecting, until the water runs clear and contains noimpurities.

If this precaution is not taken, the water inlet may become clogged, damagingthe appliance.

Fig. 33

A




5.1.2 Connecting to the hot water tap

The appliance can be supplied with mains hot water (hot water or centralheating system) on condition that it does not exceed a temperature of 60 ˚C.In this case the washing time will be approximately 15' shorter and thewashing efficiency will be slightly less.

5.1.3 Anti-flooding device (on some models only)

Some models are fitted with a system that cuts off the water supply in theevent of a fault in the inlet pipe or leakage from inside the appliance, THUSPREVENTING DAMAGE TO THE HOME. If for any reason the WATERSTOPbox (which contains electrical parts) is damaged in any way, immediatelydisconnect the plug from the mains power supply.

To guarantee operation of the anti-flooding safety device the box A with thewater inlet pipe must only be connected to the tap in the position illustratedin Fig. 34.

The supply pipe must never be cut, as it contains electrically poweredelements. If the pipe is not of a sufficient length for proper connection, it canbe replaced by another of the required length, available as a spare part.

Fig. 34

A

A




5.2 Connecting to the drainage system

The drainage pipe can be connected as follows:

1. To the sink drain siphon, ensuring that the drainage pipe is fastened to theworktop to prevent water from returning to the dishwasher;

2. To a drainage pipe with a minimum diameter of 40 mm;

3. Resting it on the sink, using the special plastic U-bend provided to preventcrushing or excessive curving of the pipe (Fig. 35). The special plasticU-bend must be firmly fixed to the wall to prevent the drainage pipe frommoving and draining water anywhere but into the sink.

In all cases, the free end of the pipe must measure between 40 and 100 mmand it must not be underwater.

6 CONNECTION TO THE MAINS

Insert the plug into a power socket fitted with a proper earthing connection,after first checking that the voltage and frequency of the mains power supplycorrespond to the values indicated on the rating plate on the appliance’sstainless steel door fairing, and that the system to which it is being connected issized for the maximum load indicated on the plate. If the socket to which theappliance is connected does not correspond to the plug, always replace it witha suitable plug, rather than using adapters or extensions, as these might result inoverheating and therefore create a fire hazard.

Fig. 35

A




CAUTIONS AND ADVICE

Positioning

The appliance can be placed with its sides or back to adjacent units or to thewall. The dishwasher is fitted with water supply and drainage pipes that canbe turned to the right or left to allow for proper installation.

Levelling

Once the appliance has been positioned, screw the feet in or out to adjust theheight of the appliance, if necessary, so as to level it horizontally; under nocircumstances must it be inclined by an angle of more than 2˚.

Good levelling will ensure that the dishwasher operates correctly.

Supply and drainage pipes

Do not use drainage pipes with extensions over 3 metres in length, as thesemight reduce the efficiency of the appliance.

Should it be necessary to use a water supply pipe longer than the oneprovided with the appliance (with waterstop), the spare parts code is 038498and the pipe is 4 metres long.

Installing the product

Always use the two teflon slides provided with the appliance to avoiddamaging the floor when inserting the appliance into the fitting space, and tofacilitate its extraction for any technical servicing required.




Accessories supplied with the appliance

Anti-condensation kit (supplied standard for some models and markets)

Code 36547

Kit for end-of-assembly fitting

Code 059638

Waterstop kit, length 4 m

Code 038498

FITTED DISHWASHER WITH VISIBLE CONTROL PANEL

Code Name Amount195024323 Folder with panel fixing template 1

047373 Slide block for feet 2

053019 ACCESSORY KIT048203 Solid wood connection bracket 2

AF.TC.4X25 for Chipboard 2AF TSP 4X16 for Chipboard 6

FITTED, TOTALLY HIDDEN DISHWASHER

Code Name Amount195024324 Folder with panel fixing template 1

047373 Slide block for feet 2

055008 ACCESSORY KIT048203 Solid wood connection bracket 2

AF.TC.4X25 for Chipboard 2AF TSP 4X16 for Chipboard 6

043325 Solid wood connection block 2




Merloni Elettrodomestici spaviale Aristide Merloni, 47 - 60044 Fabrianotel. 0732/6611 - telex 560196 - fax 0732/662954www.Merloni.com


Date post:	18-May-2018
Category:	Documents
Upload:	lythuan
View:	216 times
Download:	2 times

DISHWASHER - Indesit Company -...

Documents