Grounds 8Driveway 8Walkway 8Porch 8Courtyard 9Patio 9Gutters 9Retaining Walls 10Hose Bibs 10Patio Cover 10Gates 11Wood Fence 11Wrought Iron Fence 12Chain Link Fence 12Block Wall 12Stair Railing 12Grading / Yard Drainage 13Irrigation 13Sub-Surface Drainage 14Trees 14
Exterior 14Walls 14STUCCO 14WOOD SIDING 15Trim 16WOOD TRIM 16FOAM TRIM 16Electrical 17
NOTESBarbecue 17Fountain 17Exterior Closets 18
STRUCTURAL SYSTEMS 18Wall Framing 18Roof Framing 18Concrete Slab Foundation 19Raised Foundation 19Sub-Grade Area 19Raised Foundation Ventilation 20Raised Foundation Framing 20Raised Foundation Electrical 21Stem-Wall Foundation 21
ROOFING 21Composition Shingles 22Concrete / Other Tile Roofing 22Wood Shingles 22Flat Roofing 23Cal-Shake roofing 23Roof Flashings 23
CHIMNEYS 24Factory Built Chimney 24Masonry Chimney 24Pre-Cast Chimney 25Free-Standing Vent Stack 25Gas Appliance Termination 26
INTERIOR FIREPLACE 26Factory built Fireplace 26Masonry Fireplace 27Gas Appliance Fireplace 28Wood / Pellet Fireplace / Stove 28
PLUMBING 28Main Water Supply 29
copyright diyinspectionchecklist.com 2018 �2
NOTESRegulator 29Water Pressure 29PRV (Pressure Relief Valve located at the main water supply) 29Supply Piping 29The water supply piping is: COPPER PLASTIC GALVANIZED 29COPPER Supply Piping 30PLASTIC Supply Piping 30GALVANIZED Supply Piping 30Drain-Waste-Vent Piping 31Fuel Supply 31Water Heater 32
GARAGE 34General Conditions 34
Garage Slab 34Garage Separation Wall 35Garage Walls and Ceiling 35Garage Ventilation 35Garage Fire door 35Garage Side Man-Door 36Garage Framing 36Vehicle Door(s) Rollup / Tilt up 36Automatic Opener(s) 37Garage Electrical 37Garage Stairs 37Garage Windows 38
ELECTRICAL 38General Comments 38Weather Head (Aerial Service) 39Underground Service 39Service Panel Cover 40Dead Front Cover 40Service Size 40Wiring Methods 40Bus Bar 40
copyright diyinspectionchecklist.com 2018 �3
NOTESInfrared Observations 41Circuit Breakers 41Panel Wiring 41Neutral / Grounding Bus 41Equipotential Bonding 42Wiring Type 42Grounding System 42
SUB-PANEL 43General comments 43Sub Panel Service Panel Cover 43Sub Panel Dead Front Cover 43Sub Panel Service Size 43Sub Panel Wiring Methods 43Sub Panel Bus Bar 43Sub Panel Infrared Observations 44Sub Panel Circuit Breakers 44Sub Panel Wiring 44Sub Panel Neutral / Grounding Bus 44Sub Panel Wiring Type 44Sub Panel Grounding System 45
INTERIOR (room) ____________ 45Electrical 45Interior Doors 46Exterior Doors 47Windows 48Flooring 49Walls 50Ceilings 50Egress 51Interior Bar 51Cabinetry 51Sky-Lights 51
STAIRS 52
copyright diyinspectionchecklist.com 2018 �4
NOTESStair Railing 52Stair Treads 52
LAUNDRY 52General Comments 52Supply piping 52Waste 53Gas Supply 53Electrical 53Dryer Duct 53Cabinetry 53Combustion / Make-up Air 54Room Ventilation 54Washing Machine Pan 54Laundry Sink 54Electrical 54
KITCHEN 55General Comments 55Electrical 55Countertop 57Countertop Observations 57Kitchen Sink 57Garbage Disposal 58Kitchen Cabinets 58Gas / Electric Cook top 59Gas / Electric Oven 59Exhaust Ventilation / Light 59Dishwasher 60
BATHROOMS 60Electrical 60Toilet 61Sink 61Ventilation Fan 62Bathtub / Shower enclosure 62
copyright diyinspectionchecklist.com 2018 �5
NOTESHydromassage Bathtub 63Vanity 64
ATTIC 64Attic Access 64Attic Insulation 64 Attic Framing 65Attic Ventilation 65Attic Electrical 65Attic Exhaust Ducts 66Factory Built Chimney Flue / Fire Stop 66Masonry Chimney Observations 66Attic Separation wall (Condo / Town-house) 66
Heating System 67Heating System Observations 67Combustion Chamber 67Venting 67Fuel Supply 68Combustion / Make up Air 68Evaporative Coil 68Circulating Fan 68Condensate Drain(s) 69Thermostat(s) 69Return Air 69
AIR CONDITIONER 69General Observations 70Electrical 70Refrigerant Lines 70Temperature Differential 71
REGISTERS AND DUCTS 71Flexible Ducts 71Asbestos Ducts 71Rigid Fiberglass / Metal Ducts 71Thermostatically Controlled Dampers 72
copyright diyinspectionchecklist.com 2018 �6
NOTESRegisters 72
SWIMMING POOL AND SPA 72Water Fill and Overflow 72Disinfectant type 73Pool Tile 73Pools Interior Finish Material 73Coping 73Pool Deck 74Skimmer 74Pool Drains 74Cleaner Machine 75Lighting 75Diving Board / Diving Rock 75Slide 75Ladder / Railing 76Pool Pumps 76Air Blower 78Piping 78Valves 78Filtration 79Heating System 79Gas Piping 79Electrical 80Sub Panel Service Panel Cover 80Sub Panel Dead Front Cover 80Sub Panel Service Size 81Sub Panel Wiring Methods 81Sub Panel Bus Bar 81Sub Panel Infrared Observations 81Sub Panel Circuit Breakers 81Sub Panel Wiring 82Sub Panel Neutral / Grounding Bus 82Sub Panel Wiring Type 82Sub Panel Grounding System 82
copyright diyinspectionchecklist.com 2018 �7
NOTES
GroundsDriveway
Driveway(s) Okay
Cracks less than 1/8” (Typical)
Cracks greater than 1/4” (Non typical)
Settled concrete surface
Settled brick surface
Raised surface (trip hazard)
Raised surface tree root damage - (DIY TIP: Pay close attention to yard drain pipes as well as sewer drain piping and main water supply piping).
Newer sections (may suggest prior damage here)
WalkwayWalkways Okay
Cracks less than 1/8” (Typical)
Cracks greater than 1/4” (Non typical)
Settled concrete surface
Settled brick surface
Raised surface (trip hazard)
Raised surface tree root damage - (DIY TIP: Pay close attention to yard drain pipes as well as sewer drain piping and main water supply piping).
Newer sections (may suggest prior damage here)
PorchPorch Okay
Cracks less than 1/8” (Typical)
Cracks greater than 1/4” (Non typical)
Settled concrete surface
Settled brick surface
copyright diyinspectionchecklist.com 2018 �8
NOTESRaised surface (trip hazard)
Raised surface tree root damage - (DIY TIP: Pay close attention to yard drain pipes as well as sewer drain piping and main water supply piping).
Newer sections (This may suggest prior damage here)
CourtyardCourtyard Okay
Cracks less than 1/8” (Typical)
Cracks greater than 1/4” (Non typical)
Settled concrete surface
Settled brick surface
Raised surface (trip hazard)
Raised surface tree root damage - (DIY TIP: Pay close attention to yard drain pipes as well as sewer drain piping and main water supply piping).
Newer sections (may suggest prior damage here)
PatioPatio Okay
Cracks less than 1/8” (Typical)
Cracks greater than 1/4” (Non typical)
Settled concrete surface
Settled brick surface
Raised surface (trip hazard)
Raised surface tree root damage - (Pay close attention of yard drain pipes as well as irrigation piping). Test all yard drains before purchase!
Newer sections (may suggest prior damage here)
GuttersGutters Okay
Sagging gutters
Missing / damaged screens
Debris or water filled
copyright diyinspectionchecklist.com 2018 �9
NOTESMissing or loose nails
Rusted or deteriorated
Leaking (seams may require sealant)
Gutter downspouts drain too close to the building (less than 6 feet)
Retaining WallsRetaining walls Okay
Loose materials
Wood planks / rail road ties / telephone poles (may not be suitable as retaining wall materials)
Segmental wall with no angle / Is vertical - (DIY TIP: check maximum height for this material)
Stacked concrete not grouted installed - (DIY TIP: check maximum height for this material)
Cracks in block or concrete
Leaning wall - (DIY TIP: Have contractor evaluate)
Tree root damaged - (DIY TIP: Have contractor evaluate)
No visible drains in wall / is leaking
Wall close to the house / dirt against the building / lacks drainage - (DIY TIP: Have contractor evaluate)
Hose BibsHose bibs Okay
Hose bib pipe is loose in the wall
Hose bib: ___ handle ___ riser ___ pipe leaks continually
Missing vacuum breaker
Hose bib is stripped
Missing handle
Hose bib riser is loose and suggested to be better secured to wall (vertically)
Hose bib is galvanized when majority of house is re-piped in copper - (DIY TIP: Have contractor evaluate to determine whether dissimilar metal contact was made and / or how much galvanized material still exists within the wall)
Patio CoverPatio cover Okay
copyright diyinspectionchecklist.com 2018 �10
NOTES*DIY TIP Check permits
Wood is weathered
Wood is moisture damaged
Seal the ledger (wood board that attaches to the building) attachment to the house
Post to slab contact (No space between wood and concrete / dirt)
No ledger attachment (Rafters are attached directly to fascia board)
Rafter boards sagging (Over spanned / rafters are too long)
Beam is sagging (Over spanned / beam is too long)
Wood sheathing for roof is moisture damaged - (DIY TIP: Have contractor evaluate the roof covering materials as well as determine if the roof leaks)
GatesGates Okay
Gates do not close unassisted leading to pool - (*Safety concern)
Gate is damaged and will not operate at all
Gate rubs the ground / wall
Gate is wood and deteriorated
Gate is wrought iron and rusted
Gate was locked remember to re-check
Refer to our pool barrier safety page on our website if this property possesses a swimming pool or spa
Wood FenceWood Fence Okay
Wood fence has rot
Wood fence has missing boards
Wood fence has wood members which are not “Rot Resistive” (Cedar, California Redwood, Cypress, Teak)
Wood fence Leans / Sways
Wood fence is beyond its useful life
Wood posts are not secured into footings
Wood fence damage is a safety hazard due to swimming pool / spa present
copyright diyinspectionchecklist.com 2018 �11
NOTES
Wrought Iron FenceWrought Fence Okay
Wrought iron fence is rusted / deteriorated
Wrought iron fence is disconnected from base / wall attachment
Wrought iron fence sways - (Be sure to inspect the point at which the fence is secured such as the top of a block wall or into a footing)
Wrought iron fence is damaged / beyond its life
Chain Link FenceChain Link Okay
Chain link fence is damaged / missing pieces
Chain link fence is used as a pool barrier and has small openings (*safety hazard due to swimming pool)
Chainlink rusted
Block WallBlock fence Okay
Block fencing leans
Block fencing sways
Blocks are loose
Blocks are missing
Blocks are cracked
Cap material is loose / missing
Tree roots causing damage to wall
Stair RailingStair / Railing okay
Stair treads are smaller than 10”
Stair Risers are taller than 7 ¾”
copyright diyinspectionchecklist.com 2018 �12
NOTESStair risers / treads possess more than a 3/8” difference between them
Railings are needed one one side when there are more than 4 risers
Railings are loose
Railings are not between 34-42”
Railings are damaged
The space between “pickets” are wider than 4” - (Hazard to small children)
Grading / Yard DrainageGrading okay
The site possesses a *very steep hillside up or down - (DIY TIP: Have contractor evaluate)
The grade slopes towards the house at any point around the property - (DIY TIP: Have contractor evaluate)
There are holes in the yard which may suggest the removal of a tree - (DIY TIP: Ask the seller if there was a tree removed if so, be aware of the location of the underground piping – inspect as necessary)
There are areas where the soil or concrete touch the bottom of the house - (DIY TIP: Have contractor evaluate)
Hillside has no visible swales or drainage basin - (DIY TIP: Have contractor evaluate)
There are planters which are close to / up against the house _____ with _____ without the ability to drain in the event they become flooded
There is insufficient slope away from the house (6” in first 10 feet dirt)( 2% slope for solid surface)
Solid surfaces are higher than the lower edge of the exterior wall of the building risking water entry into the building - (DIY TIP: Have contractor evaluate)
IrrigationIrrigation Okay
Leaking valves / pipes / sprinkler heads
Irrigation valves too low to grade - (possible cross contamination of potable water supply)
Sprinkler heads spraying onto the building finishes - (re adjustment needed)
Damaged / Missing sprinkler heads
Timer damaged / missing
Loose / exposed wiring
copyright diyinspectionchecklist.com 2018 �13
NOTES
Sub-Surface DrainageSub surface drains Okay
Sub grade drainage noted but there are no holes curbside (where does the water go?)
Vegetation growing from within the drain pipes
Stains surrounding the drains – (suggesting the drain is blocked)
Trees close to sub grade drain piping - (video scan suggested here)
Missing / damaged drain covers
TreesTrees on hillside
Dead trees on property close to the house or possible piping - (DIY TIP: Have contractor evaluate)
Trees close to plumbing or other piping - (DIY TIP: Have contractor evaluate) (A video inspection of piping may be necessary here)
ExteriorWalls
STUCCOStucco walls Okay
Cracks 1/16 – 1/8” (These cracks are considered typical in stucco construction)
Cracks 1/8-1/4” + (DIY TIP: Have contractor evaluate)
Cracks diagonal at the window or door (DIY TIP: Have contractor evaluate)
Spalling / deterioration of the stucco covering (*check sprinkler spray and gutter runoff)
Holes in the stucco wall covering
Penetrations around pipes and trim needs to be sealed
Stucco needs to be painted
copyright diyinspectionchecklist.com 2018 �14
NOTESThe wall was recently painted - may hide damage or previous repairs
Missing material in large quantity
Exposed building wrap / paper
Exposed wood framing - (DIY TIP: Have contractor evaluate)
Bowed wall … vertical / horizontal - (DIY TIP: Have contractor evaluate)
Leaning wall - (DIY TIP: Have contractor evaluate)
Raised Foundation: Cracks in wall at the sill plate level (This may suggest the building has shifted from its attachment to the foundation) - (DIY TIP: Have contractor evaluate)
Raised Foundation: Repairs in wall at sill plate level (raised foundation) - (DIY TIP: Have contractor evaluate)
Large patches in stucco - (be aware that the building paper can be damaged when cutting into stucco the stucco wall) (DIY TIP: Have contractor evaluate)
Doors / windows added into the stucco wall (*be aware that when adding doors and windows into walls may require supports to be placed above the windows or doors as exterior walls are load bearing walls) - (DIY TIP: Have contractor evaluate)
Doors / windows added into the stucco wall - (*be aware that when adding doors and windows into walls may require the cutting into the building envelope or paper wrap which protects the building from moisture entry) - (DIY TIP: Have contractor evaluate)
The weep screed is rusted and deteriorated (be aware that sprinklers may be damaging the weep screed)
The weep screed is not installed (Weep screeds are designed to drain moisture behind the stucco and in front of the building paper) (DIY TIP: Have contractor evaluate)
The weep screed has been stuccoed over (wall may not drain properly) (DIY TIP: Have contractor evaluate)
Large gap between the weep screed and the building
The bottom of the wall touches the ground i.e. concrete / soil (no weep screed means the wall may not drain sufficiently. This was common practice for older homes 60’s and before) (DIY TIP: Have contractor evaluate)
Vegetation contact with the walls
WOOD SIDINGSiding overall: OKAY FAIR POOR
Siding shows signs of typical or normal wear
Siding is weathered – needs paint
Rot was observed in the wood siding
Missing siding boards
copyright diyinspectionchecklist.com 2018 �15
NOTESLoose / warped siding boards
Exposed building paper - (DIY TIP: Have contractor evaluate)
Wood siding makes contact with the soil or concrete
Wood siding connections or joints need to be sealed
Holes and penetrations need to be sealed
Vegetation contact with wood siding
MASONRY SIDING
Masonry facing added to the front of the house w/o flashings - (DIY TIP: Have contractor evaluate)
Masonry facing damaged / missing materials
Masonry material deteriorated
Sealant is suggested at various penetrations
Siding overall: OKAY FAIR POOR
TrimWOOD TRIM
Wood trim Okay
Wood twisted / weathered needs paint
Wood Needs to be sealed where connected to the building
Wood possess dry rot
Termite damaged wood noted
FOAM TRIMFoam trim Okay
Cracks in foam trim
Loose foam trim
The trim was recently painted - may hide damage or previous repairs
Weathered foam trim
Trim needs to be sealed to the wall
copyright diyinspectionchecklist.com 2018 �16
NOTES
ElectricalElectrical Okay
Are the plugs GFI protected - (Safety concern if the exterior plugs are not GROUND FAULT protected)
Non operational plugs
Plugs missing cover plates - (Safety concern)
Exposed / loose wiring hazard - (Safety concern) (DIY TIP: Have contractor evaluate)
Loose or damaged junction boxes - (Safety concern) (DIY TIP: Have contractor evaluate)
Light fixtures missing glass
Loose light fixtures
Light fixtures need to be sealed where they make contact with the house
Lights that do not operate. Location(s): ______________________________________________
BarbecueBBQ Okay
Does the BBQ operate Y/N
Damaged knobs
Missing parts
Enclosure / base / built-in is made of wood - (*Safety concern) (DIY TIP: Have contractor evaluate)
Located under a solid combustible cover - (*Safety concern) (DIY TIP: Have contractor evaluate)
Located under trees - (*Safety concern)
FountainFountain Okay
Does the fountain operate Y/N
Empty not tested
Concrete pieces loose
Plug not GFI protected - (*Safety concern) (DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �17
NOTES
Exterior ClosetsClosets okay
Closets are full and therefore not inspected
Doors are damaged / weathered
Doors are hollow core
Moisture damaged walls within the closet - (*DIY TIP: Have contractor evaluate)
STRUCTURAL SYSTEMS Wall Framing
Wall framing Okay
Wood framing is visibly damaged / cracked / missing
Termite damage
Moisture damaged
Contact with grade
Framing members appears to have been repaired - (*DIY TIP: Have contractor evaluate)
Framing members appear to have been modified - (*DIY TIP: Have contractor evaluate)
Roof FramingALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Roof framing Okay
Missing framing members
Cracked roof framing members
Moisture stained wood
Repairs observed
Wood trusses cracked / damaged / missing
copyright diyinspectionchecklist.com 2018 �18
NOTESTruss / Ceiling joists removed for whole house fan
Cracks in wood framing members
Wood which is too long for span
New Tile roofing on existing roof framing
Scorching suggests previous fire
Concrete Slab FoundationSlab Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Vertical cracking in stem-wall of the slab
Horizontal cracking in stem-wall of slab
Deteriorated concrete slab (crumbling)
Repairs to the concrete slab
Post tension slab with cracks larger than 3/32” (*DIY TIP: Have contractor evaluate)
Raised FoundationAccessibility Okay
Not accessible – no entrance
Access screen damaged / missing
Access too small - unable to access
Not entered due to pests observed under the house
Not accessed – too wet
Sub-Grade AreaSub grade area Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Sub grade moist….. ___ Very ___ Moderately ___ Somewhat damp
Signs of previous moisture
copyright diyinspectionchecklist.com 2018 �19
NOTESWater currently standing / ponding under house
Deep ruts cut from plumbing repairs or otherwise (* Ask seller if any repairs were performed)
Vegetation growing under house
Debris under the house
Rodent activity
Termite activity
Mold / mildew
Raised Foundation VentilationVentilation Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
No vents for sub-grade area
Vent screens damaged - may allow rodents into sub-grade area
Vents too close to the ground - may allow water under the building
Too few vents for size of underfloor area - too little ventilation
Ventilation helped by fan - indication of too little ventilation
Additional ventilation needed – mold – mildew – moisture observed under the house
Raised Foundation FramingFraming Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Missing framing
Undersized framing
Moisture / insect damaged framing
Soil contact with wood framing
Seismic upgrades Noted / Needed
Holes drilled / Notches cut into framing
Newer framing / repairs noted
copyright diyinspectionchecklist.com 2018 �20
NOTES
Raised Foundation ElectricalElectrical Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Loose exposed wiring not terminated (live / dead)
Loose / damaged junction boxes
Open junction boxes
Wiring laying on ground
Melted wiring
Loose Romex (NM) wiring hanging
Stem-Wall FoundationStem walls Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Vertical cracking……….. 1/16” to 1/8” 1/8” to 1/4” 1/4” Plus ++
Horizontal Cracking ……….. 1/16” to 1/8” 1/8” to 1/4” 1/4” Plus ++
No stem walls / framing sitting on….. ___ Rock ___ Dirt ___ Wood
No visible foundation bolts
Foundation Bolt spacing is less than building code requires **1/2” bolt spaced no less than 6’ and 4’ for 2 story
ROOFINGDIY Tips:
1. Because you have no idea what condition the roofing paper is in by a visual inspection or even by simply running the water over the top of the roof covering materials, we always suggest a roof inspection prior to your purchase.
2. The use of an infrared camera is strongly suggested when looking for leaks within the roofing system in conjunction with a certified water intrusion test
Estimated Roof Age __________ YEARS
copyright diyinspectionchecklist.com 2018 �21
NOTES
Composition ShinglesNumber of Layers _______
Shingles Okay
Newer Roofing - (Check for permits)
Damaged / Curling shingles - (*DIY TIP: Have contractor evaluate)
Missing shingles - (*DIY TIP: Have contractor evaluate)
Exposed Nail heads - (*DIY TIP: Have contractor evaluate)
Prior repairs performed- (* Ask sellers about this work and check for permits)
Debris on the roof deck
Roof is at the end of its useful life - (*DIY TIP: Have contractor evaluate)
Ridge cap is deteriorated / End of life - (*DIY TIP: Have contractor evaluate)
Concrete / Other Tile RoofingConcrete tile roof okay
Missing tiles (DIY TIP: Have contractor evaluate)
Slipped tiles (DIY TIP: Have contractor evaluate)
Roofing paper observed under slipped tile (DIY TIP: Have contractor evaluate)
Cracked tiles (DIY TIP: Have contractor evaluate)
Prior repairs performed (* Ask sellers about this work and check for permits)
Debris on the deck
Chipped tiles (above the head of the lower tile)
Roof is older than 30 years (* Have a roofing contractor inspect the roofing paper here)
Wood ShinglesWood shingles Okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Missing shingles
Roofing paper observed under missing shingles
Cracked / Split shingles
copyright diyinspectionchecklist.com 2018 �22
NOTESPrior repairs performed (* Ask sellers about this work and check for permits)
Debris on the deck
Roof is older than 30 years (* Have a roofing contractor inspect the roofing paper here)
Flat RoofingFlat roofing okay
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Loose roofing material
Prior repairs performed (* Ask sellers about this work and check for permits)
No bleed-out observed / fish-mouth noted (*Material is not stuck to one-another)
Ponding observed on roof deck / Poor drainage on roof deck
Material is beyond its useful life
Drain covers are missing
Drains are clogged
Cal-Shake roofingCAL SHAKE ROOFING MATERIAL IS AN INFERIOR MATERIAL AND IF YOU BELIEVE YOU HAVE THIS MATERIAL SEEK THE SERVICES OF A ROOFING CONTRACTOR TO INSPECT THIS ROOF.
ALL CONDITIONS LISTED BELOW (IF CHECKED) REQUIRE AN ADDITIONAL INSPECTION BY A PROFESSIONAL OF THIS TRADE
Missing shingles
Roofing paper observed under missing shingles
Cracked / Split shingles
Prior repairs performed (* Ask sellers about this work and check for permits)
Debris on the deck
Roof FlashingsRoof flashing okay
Rusted flashings
Missing “B” or “BW” vent caps
copyright diyinspectionchecklist.com 2018 �23
NOTESVent caps for “B” vents are rusted / Deteriorated and collapsed on top of the vent - (*DIY TIP: Have contractor evaluate)
Flashings / Vents require sealant at the penetration
“B” vent too close to a vertical wall or window
Chimney suggested to possess a “cricket”
No “kick-outs”
Valley flashing is cut short
CHIMNEYSDIY Tip:
1. Because you have no idea what condition the flue liner is in by a visual inspection or even by simply looking into the flue from the top of bottom, we always suggest a chimney inspection prior to your purchase.
2. If the house was re-piped, you should consider looking into permits or warranties
Factory Built ChimneyChimney Is okay
Chimney Sways when pressed upon (DIY TIP: Have contractor evaluate)
Cracks located within the chase stucco finish
Damaged foam trim at the top of the chase
Wood rot trim at the top of the chase
Chase cover sunken and holds water (DIY TIP: Have contractor evaluate)
Rusted chase cover (* May be a potential safety issue-have this inspected by a chimney contractor)
Missing / Damaged spark arrestor
Chimney is short and does not meet the 3-2-10 rule - (*DIY TIP: Have contractor evaluate)
Chimney was added - Check for permits
*It is always suggested that the inner flue liner of every chimney system be inspected by a professional with a camera
Masonry ChimneyChimney Is okay
Chimney Sways when pressed uponcopyright diyinspectionchecklist.com 2018 �24
NOTESCracks within the brick or grout - (*DIY TIP: Have contractor evaluate)
Ash dump door rusted or missing
Wood trim (eave / fascia) makes contact with the chimney
Missing or damaged spark arrestor (DIY TIP: Have contractor evaluate)
Cracks within the chimney cap (DIY TIP: Have contractor evaluate)
Chimney is short and does not meet the 3-2-10 rule - (*DIY TIP: Have contractor evaluate)
Chimney was added - Check for permits (DIY TIP: Have contractor evaluate)
*It is always suggested that the inner flue liner of every chimney be inspected by a professional with a camera
Pre-Cast Chimney
Chimney Is okay
Chimney Sways when pressed upon (DIY TIP: Have contractor evaluate)
Cracks within the exterior walls of the chimney - (*DIY TIP: Have contractor evaluate)
Ash dump door rusted or missing
Missing / Damaged spark arrestor (DIY TIP: Have contractor evaluate)
Chimney is short and does not meet the 3-2-10 rule - (*DIY TIP: Have contractor evaluate)
Chimney was added - Check for permits
Cracks within the chimney cap
It is always suggested that the inner flue liner of every chimney be inspected by a professional with a camera
Free-Standing Vent StackVent Is okay
Vent Sways when pressed upon (DIY TIP: Have contractor evaluate)
Vent is rusted deteriorated
Vent is not properly supported (DIY TIP: Have contractor evaluate)
Vent is short and does not meet the 3-2-10 rule - (*DIY TIP: Have contractor evaluate)
Vent was added - Check for permits
copyright diyinspectionchecklist.com 2018 �25
NOTESIt is always suggested that the inner flue liner be inspected by a professional with a camera
Gas Appliance Termination
*It is always suggested that the inner flue liner of every chimney be inspected by a professional with a camera
*You must possess the manufactures manual for installation in order to properly inspect these types of systems
INTERIOR FIREPLACEFactory built Fireplace
Fireplace Is okay
Fireplace flue is disconnected - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
Damper is stuck open / closed - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
Damper needs to be blocked in the open position when gas logs are present - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
Fireplace flue contains an excessive amount of creosote - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
Gas pipe penetrating the refractory needs to be sealed - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
Gas valve is inoperable
Refractor is cracked / deteriorated / or otherwise modified - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
The grate is not the same grate that came with the “Listed” fireplace system
The grate is installed backwards - (* This is a hazard and should be corrected prior to use)
The doors are missing - (*Factory built fireplace require their “listed” components for use)
The doors require service for ease of operation
No screens present
The gas bib is too far forward
A wood burning / pellet stove was inserted into this box - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor evaluate)
Cracked materials in the hearthcopyright diyinspectionchecklist.com 2018 �26
NOTESLog set is too large for this fireplace (DIY TIP: Have contractor evaluate)
The “burn pattern” on the refractory is not centered (DIY TIP: Have contractor evaluate)
There is soot on the exterior of the fireplace suggesting poor drafting - (* This may be a hazard and should be corrected prior to use)
The hearth extension is missing - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
The hearth extension is too small - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
The hearth extension is combustible material - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
The hearth extension has been added - made of wood - (* This may be a hazard and should be corrected prior to use)
There is insufficient clearance to combustible material surrounding the fireplace opening i.e. mantel etc… - (* This may be a hazard and should be corrected prior to use)
The mantel is loose
Masonry Fireplace
Fireplace Is okay
Fireplace flue is cracked - (* This may be a hazard and should be corrected prior to use)
Mortar is missing within the ___ Throat ___ Under the first liner ___ Firebox - (* This may be a hazard and should be corrected prior to use)
Mortar is missing from within the fire brick / Tuck-and point is needed - (* This may be a hazard and should be corrected prior to use)
The damper is frozen inoperable
The damper should be blocked in the open position with gas logs present - (* This may be a hazard and should be corrected prior to use)
Screens are missing and therefore suggested
The grate is missing / Deteriorated
The gas valve is frozen
The hearth extension is higher than the inner hearth
The gas bib is too far forward
There is soot on the exterior of the fireplace suggesting poor drafting - (* This may be a hazard and should be corrected prior to use)
The hearth extension is missing - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
copyright diyinspectionchecklist.com 2018 �27
NOTESThe hearth extension is too small - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
The hearth extension is combustible material - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
The hearth extension has been added - made of wood - (* This may be a hazard and should be corrected prior to use)
There is insufficient clearance to combustible material surrounding the fireplace opening i.e. mantel etc… - (* This may be a hazard and should be corrected prior to use)
The mantel is loose
Gas Appliance Fireplace
*This type of fireplace is suggested to be inspected by a profession with access to the installation standards and listed instructions prior to use.
The gas appliance operated by switch
There is a standing pilot - (*This may be a hazard)
Wood / Pellet Fireplace / Stove
*This type of fireplace (freestanding stove) is suggested to be inspected by a profession with access to the installation standards and listed instructions prior to use.
There is insufficient clearances to combustible materials at the Side / Front / Rear of this unit - (*DIY TIP: This is a hazard - DO NOT USE FIREPLACE - Have contractor of this trade evaluate)
PLUMBINGDIY Tips:
1. Because you have no idea what condition the main sewer line is in by a visual inspection or even by simply running the water, we always suggest a main sewer line inspection prior to your purchase.
2. If the house was re-piped, you should consider looking into permits or warranties
3. If there is fire suppression present, have a professional inspect this system
4. The use of an infrared camera is strongly suggested when looking for leaks within the plumbing system
copyright diyinspectionchecklist.com 2018 �28
NOTES5. If you find that the house is more than 30 years old or there are trees in close proximity to the
front of the house - GET A SEWER LINE SCOPE / INSPECTION
Main Water SupplyMaterial Type ___________________
Material Size _________
Original / Replaced
RegulatorThe gas valve is frozen
There is NO regulator present (*DIY TIP: Have contractor evaluate)
Regulator is leaking (*DIY TIP: Have contractor evaluate)
Regulator piping appears smaller than other piping leading into / out of regulator (*DIY TIP: Have contractor evaluate)
Water Pressure* Test the water pressure by running multiple fixtures and placing a pressure gauge onto a hose bib which is regulated
The water pressure is okay 45-60 PSI
The water pressure is too low (*DIY TIP: Have contractor evaluate)
The water pressure is too high (*DIY TIP: Have contractor evaluate)
The water pressure drops from a normal 45-60 psi to 0-20 psi during use of multiple fixtures (*DIY TIP: Have contractor evaluate)
PRV (Pressure Relief Valve located at the main water supply)
The PRV is okay
The PRV is leaking (*DIY TIP: Have contractor evaluate)
The PRV is corroded (may leak) (*DIY TIP: Have contractor evaluate)
Supply PipingThe water supply piping is: COPPER PLASTIC GALVANIZED
copyright diyinspectionchecklist.com 2018 �29
NOTES
COPPER Supply Piping*With copper piping you may experience a “ticking” noise when you test the hot water which is generally typical expansion and contraction
The copper supply piping is okay
The copper piping rattles or is noisy when fixtures are abruptly turned off (water hammering) (*DIY TIP: Have contractor evaluate)
There is surface corrosion where visible ( just inspect annually)
Piping not supported / strapped properly
Leaking was observed within the copper piping system (*DIY TIP: Have contractor evaluate)
The material looks like type “M” with a red stripe which is a thinner material (*DIY TIP: Have contractor evaluate)
There is galvanized piping intermixed with the copper piping (*DIY TIP: Have contractor evaluate)
There are galvanized connections made directly not the copper piping (*DIY TIP: Have contractor evaluate)
Prior repairs were observed or disclosed (*DIY TIP: Ask about previous repairs here)
PLASTIC Supply Piping*With plastic piping you may experience a “ticking” noise when you test the hot water which is generally typical expansion and contraction
The plastic supply piping is okay
There is surface corrosion observed at various joints or connections
Piping not supported / strapped properly
There is CPVC piping (which is a controversial material) (*DIY TIP: Have contractor evaluate)
There is Kitec piping (which is a controversial material) (*DIY TIP: Have contractor evaluate)
There is Polybutylene piping (which is a controversial material) (*DIY TIP: Have contractor evaluate)
Leaking was observed within the piping system (*DIY TIP: Have contractor evaluate)
Prior repairs were observed or disclosed (*DIY TIP: Ask about previous repairs here)
Galvanized or copper materials intermixed with this plastic piping (*DIY TIP: Have contractor evaluate)
GALVANIZED Supply PipingThe Galvanized supply piping is okay
copyright diyinspectionchecklist.com 2018 �30
NOTESSurface corrosion / blisters noted (*DIY TIP: Have contractor evaluate)
Significant reduction in water pressure when water was tested (*DIY TIP: Have contractor evaluate)
Patches noted in galvanized piping (*DIY TIP: Have contractor evaluate)
Prior repairs noted or disclosed by owners (*DIY TIP: Ask about previous repairs here)
Copper mixed with galvanized piping (*DIY TIP: Have contractor evaluate)
Piping not supported / strapped properly
Copper connections made directly onto galvanized piping (*DIY TIP: Have contractor evaluate)
Drain-Waste-Vent PipingNo visible leaks at the time of the inspection
Leaking noted (*DIY TIP: Have contractor evaluate)
Drains sloped negatively (*DIY TIP: Have contractor evaluate)
Vent piping sloped negatively (*DIY TIP: Have contractor evaluate)
Corrosion observed at drain pipe connections (*DIY TIP: Have contractor evaluate)
Asbestos piping observed (*DIY TIP: Have contractor evaluate)
Vent too close to trap
Added Drain pipe - (*DIY TIP: Check for permits)
vent pipe too close to an openable window
Drain piping not supported / strapped properly
CLEAN OUTS
Clean-out missing front / rear
Missing cap
Newer Cap (*DIY TIP: Ask about previous repairs here)
Leaking Clean out (*DIY TIP: Have contractor evaluate)
Fuel SupplyFuel Type: Natural Gas / Propane
METER
Meter okay
copyright diyinspectionchecklist.com 2018 �31
NOTESMeter needs to be better protected by a Bollard pole
Meter too close to the garage air vent (*DIY TIP: Have contractor evaluate)
Meter too close to door or window (*DIY TIP: Have contractor evaluate)
Meter too close to grade
Gas pipe
Gas pipe okay
Missing drip legs / Sediment traps
Added line noted (*DIY TIP: Check for permits)
Incorrect materials for gas pipe (*DIY TIP: Have contractor evaluate)
Missing shutoff valve 3’ before appliance (*DIY TIP: Have contractor evaluate)
Metallic gas piping is not allowed outdoors in or within six inches of the ground.(unless wrapped or protected coating applied) (*DIY TIP: Have contractor evaluate)
Incorrectly supported
Not protected below ground (*DIY TIP: Have contractor evaluate)
Gas leak detected (*DIY TIP: Have contractor evaluate)
Water Heater
Capacity ____ Gallons
Year __________
Water-heater okay
Water heater is new - (*DIY TIP: Check for permits)
Water heater knocks
Bollard protection needed
Lacks Clearance to top / front / side / rear
Water heater lacks combustion / make-up air (*DIY TIP: Have contractor evaluate)
Fuel
Fuel leak (*DIY TIP: Have contractor evaluate)
Fuel line too short
Sediment trap missing
Fuel line too small
Fuel line incorrect materialscopyright diyinspectionchecklist.com 2018 �32
NOTESFuel line kinked
Fuel valve damaged (*DIY TIP: Have contractor evaluate)
Temperature Pressure Relief Valve
TPR Flexible materials
TPR does not extend to the exterior
TPR too close to grade (min 6”-24” max) (*DIY TIP: Have contractor evaluate)
TPR drain incorrectly into a pan (*DIY TIP: Have contractor evaluate)
TPR present / no drain pipe
TPR missing - (*DIY TIP: This is a hazard)
TPR drain pipe incorrect materials
TEE installed within the TPR drain pipe (*DIY TIP: Have contractor evaluate)
TPR drain pipe too small (3/4” or less) (*DIY TIP: Have contractor evaluate)
Too many 90 degree fittings in the TPR drain pipe
Unable to verify the termination point (*DIY TIP: Have contractor evaluate)
TPR drain pipe kinked
Water Heater Base
Water heater base is damaged
Water heater base is stained (*DIY TIP: Ask about previous leaks here)
Water heater base possess mold (*DIY TIP: Have contractor evaluate)
Water heater base is too small (*DIY TIP: Have contractor evaluate)
Water heater base is sagging (*DIY TIP: Have contractor evaluate)
Pan is needed at the water heater base
Base is not 18” high (*DIY TIP: Have contractor evaluate)
Water heater base is unstable (*DIY TIP: Have contractor evaluate)
Water Heater straps
Missing straps (*DIY TIP: This is a hazard)
Straps are loose (*DIY TIP: Have contractor evaluate)
Only one strap (*DIY TIP: This is a hazard)
Straps not installed at 1/3 and 1/3 locations
Incorrect materials used
Water Heater Vent
copyright diyinspectionchecklist.com 2018 �33
NOTESVent is too close to combustible materials (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Vent is asbestos Transite (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Vent is incorrectly installed (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Vent is sloped incorrectly (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Draft hood is missing / loose (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Thimble reducer needed (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Screws suggested in vent connections
Water Heater Supply Piping
No shutoff valve installed (*DIY TIP: Have contractor evaluate)
No means to disconnect the water heater (union / valve)
Supply pipe kinked
Corrosion observed at the supply piping
GARAGEGeneral Conditions
Number of Vehicles 1 2 3 4 5 6 ____
Converted into living space (*DIY TIP: Check for permits)
Most of the garage was not fully visible
Garage SlabCracks observed in the garage (<.25”)
Cracks observed in the garage (>.25”) (*DIY TIP: Have contractor evaluate)
Efflorescence in concrete
Slab is deteriorated (*DIY TIP: Have contractor evaluate)
Slab lacks minimum slope (*DIY TIP: Have contractor evaluate)
Garage slab is lower than exterior grade (*DIY TIP: Have contractor evaluate)
Stem wall significant cracking (*DIY TIP: Have contractor evaluate)
Flammable material on floor
garage lower than driveway (*DIY TIP: Have contractor evaluate)copyright diyinspectionchecklist.com 2018 �34
NOTESMoisture seeping from under slab (*DIY TIP: Have contractor evaluate)
Concrete popping
Garage Separation WallHoles observed in separation wall (*DIY TIP: Have contractor evaluate)
Seal penetrations in separation wall (*DIY TIP: Have contractor evaluate)
Ladder in fire separation wall (*DIY TIP: Have contractor evaluate)
Air duct through separation wall (*DIY TIP: Have contractor evaluate)
Cracks observed in the wall (<.25”)
Cracks observed in the wall (>.25”) (*DIY TIP: Have contractor evaluate)
Garage Walls and CeilingStains in drywall (*DIY TIP: Ask about previous leaks here)
Missing drywall materials
Cracks observed in the wall (<.25”)
Cracks observed in the wall (>.25”) (*DIY TIP: Have contractor evaluate)
Garage VentilationLouvers suggested in vents
Missing vent covers
Screens damaged
Vents covered-over
Vents needed
Garage Fire doorDoor does not self close (*DIY TIP: Have contractor evaluate)
Pet door installed fire door (*DIY TIP: Have contractor evaluate)
Fire door needs to be weather stripped / Smoke seal
Door sweep missing
Threshold loose / missing screws
copyright diyinspectionchecklist.com 2018 �35
NOTESDoor rubs frame / sill
Double cylinder deadbolt installed in door (*DIY TIP: Safety concern)
Door hardware missing
Door hardware worn
Fire door is a hollow core door-not fire rated (*DIY TIP: Have contractor evaluate)
Garage Side Man-DoorDoor is hollow core door - solid is suggested
Door is badly damaged / weathered
Door frame badly weathered
Needs weatherstripping
Door rubs frame / sill
Self closer needed - (*DIY TIP: Door leads to pool area - Safety concern)
Door hardware is worn / damaged
Garage FramingGarage framing is stained (*DIY TIP: Ask about previous leaks here)
Cracked wood framing members observed (*DIY TIP: Have contractor evaluate)
Building paper torn deteriorated (*DIY TIP: Ask about previous leaks here)
Holes bored into framing exceed maximum size
Added framing observed (*DIY TIP: Check for permits)
Door or window added into wall (*DIY TIP: Check for permits)
Insect / moisture damaged wood framing
Vehicle Door(s) Rollup / Tilt up
Door binding noted
Damaged door noted
Lower seal damaged
Side seal damaged
Glass damaged
Wood moisture damaged
Metal panel(s) damaged
copyright diyinspectionchecklist.com 2018 �36
NOTES
Automatic Opener(s)Automatic retractor Okay
Automatic retractor missing (*DIY TIP: This is a hazard)
Automatic retractor too high (+12”) (*DIY TIP: Have contractor evaluate)
Door closes halfway then retracts when button pressed (*DIY TIP: Have contractor evaluate)
Loose chain
Missing emergency pull cord
Very noisy closer
Cover missing
Lights non operational
Damaged non functional
Garage ElectricalGFIs suggested throughout
GFIs defective (*DIY TIP: Have contractor evaluate)
non metallic wiring (romex) exposed and installed in hard way (*DIY TIP: Have contractor evaluate)
Added wiring throughout (*DIY TIP: Check for permits)
Electrical conduit improperly supported (*DIY TIP: This is a hazard)
Plus not grounded (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Plugs are reversed polarity (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Plugs damaged (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
plugs scorched (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Switches -unable to determine their function throughout
Damaged switches / receptacles (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
Junction boxes missing cover plates (*DIY TIP: This is a hazard)
Open knockouts in junction boxes (*DIY TIP: This is a hazard)
Loose wiring, exposed wires not protected (*DIY TIP: This is a hazard)
Garage StairsStair / Railing okay
copyright diyinspectionchecklist.com 2018 �37
NOTESTREADS
Stair treads are smaller than 10” (*DIY TIP: This is a hazard)
Stair treads do not possess a “nosing”
Stair Risers are taller than 7 ¾” (*DIY TIP: This is a hazard)
Stair risers / treads possess more than a 3/8” difference between them (*DIY TIP: This is a hazard)
RAILING
Railings are needed one one side when there are more than 4 risers (*DIY TIP: This is a hazard)
Railings are loose (*DIY TIP: This is a hazard)
Railings are not between 34-42”
Railings are damaged (*DIY TIP: This is a hazard)
The space between “pickets” is wider than 4” - (Hazard to small children) (*DIY TIP: This is a hazard)
Garage WindowsWindow is Okay
Window is cracked
Window is difficult to operate
Window is fogged
Window is inaccessible
ELECTRICALGeneral Comments
DIY Tips:
1. Some houses possess multiple electrical panels. We suggest printing this section as many times as necessary to accommodate the number of panels at your property.
All conditions listed below (if checked) require an additional inspection by a professional of this trade
All conditions are considered a hazard if checked
Service feed is UNDERGROUND / AERIAL
copyright diyinspectionchecklist.com 2018 �38
NOTES
Weather Head (Aerial Service)Overhead service is Okay
Weather head is damaged
Service mast is leaning / rusted / cracked / damaged
Service conductors are too small for this size home
Service conductors not attached to weather head mast or roof cleat
Roof cleat is loose or pulled away from roof deck
Bolts on roof cleat need to be sealed
Neutral wire disconnected from mast
Flashing into the roof is missing / needs sealant/ damaged
Service mast is located more then 48” from eave
Wire entering Weather head is closer than 18” to the roof deck
Service conductors not suggested to pass over the roof more than 6 feet
Service conductors must maintain these clearances:
• 8 feet over flat roof
• 10 feet over grade
• 10 feet over deck within 3 feet
• 12 feet over driveway
• 14.5 over diving board
• 15 feet over alley
• 18 feet over road
• 22.5 feet over swimming pool
Wire entering Weather head are frayed / connections are exposed
Service wires laying on the roof deck
Service mast suggested to be better supported
No drip loop observed
Service wires too close to trees / buildings
Underground Service Check to see if any trees are close to underground feeders
copyright diyinspectionchecklist.com 2018 �39
NOTESExposed underground wires observed
Exposed service feeder wires above grade
Service Panel CoverSPC is Okay
SPC is damaged
SPC is loose
SPC hinges missing / damaged / loose
SPC missing
Dead Front CoverDFC is okay
DFC is missing
DFC is damaged
DFC is missing screws
DFC is screws are pointed and not blunt
DFC is missing breaker labels
DFC breaker labels are worn
DFC is missing knockouts
DFC is not tight to breakers leaving a gap
DFC is not original to panel / replaced / modified
DFC is rusted / deteriorated
Service SizeThe service size is _________ amps
The panels rating is __________ amps
Wiring MethodsThe wiring appears to be Non Metallic cable (Romex)
The wiring is drawn through conduit
Bus Bar
copyright diyinspectionchecklist.com 2018 �40
NOTESThe bus bar looks okay
The bus bar is scorched / damaged
The bus bar appears to have been replaced
Infrared ObservationsNo visible issues
Heat in excess observed at one or more connections / breakers / wires
Circuit BreakersCircuit breakers okay
Damaged Circuit breakers
Circuit breakers not approved for this panel board
Circuit breakers scorched
Circuit breakers loose
Circuit breaker is tripped for unknown reasons
AFCI (blue button) recalled
GFCI breaker defective
Circuit breakers amps too large for appliance / circuit / wire
Panel WiringWiring looks okay
Wires scorched
Wires are corroded or deteriorated
Wires loose in panel not terminated
Two or more wires into one breaker
Wire is too small for breaker size
Wire / circuit is not protected by breaker / fuse (direct tap)
Neutral / Grounding BusPanel appears to be bonded
No visible bond observed (The bus bars appear to be floating)
Bus is deteriorated
Two or more neutral wires under one terminal
copyright diyinspectionchecklist.com 2018 �41
NOTESGround and neutral wire under one terminal
GROUNDING ELECTRODE CONDUCTOR disconnected
Equipotential BondingEQ bond is complete
EQ bond is not visible / missing
EQ bond was terminated in re-pipe
No EQ bond due to plastic water pipes
EQ bond present but not compete to gas and hot water pipes
EQ bond clamps loose
EQ bonding conductor is too small ( < #8 AWG )
Wiring TypeThe wire type is non metallic ( Romex)
The wire type is stranded wire pulled through conduit
The wire type is old Aluminum
The wire type is pre-1984 Non metallic ( Romex)
Grounding SystemThe GROUNDING ELECTRODE CONDUCTOR (GEC) was verified
There is no GEC installed
The GEC is incorrectly sized
The GEC is was not visible to verify
The GEC is spliced
There are two or more GROUNDING ELECTRODES
The GEC has been nullified
The GEC requires a bonding jumper
The GEC is subject to damage and not protected
The grounding rod electrode is exposed and not completely embedded
There is only one grounding electrode where two are required
copyright diyinspectionchecklist.com 2018 �42
NOTES
SUB-PANELGeneral comments
Sub Panel Service Panel CoverSPC is Okay
SPC is damaged
SPC is loose
SPC hinges missing / damaged / loose
SPC missing
Sub Panel Dead Front CoverDFC is okay
DFC is missing
DFC is damaged
DFC is missing screws
DFC is screws are pointed and not blunt
DFC is missing breaker labels
DFC breaker labels are worn
DFC is missing knockouts
DFC is not tight to breakers leaving a gap
DFC is not original to panel / replaced / modified
DFC is rusted / deteriorated
Sub Panel Service SizeThe service size is _________ amps
The panels rating is __________ amps
Sub Panel Wiring MethodsThe wiring appears to be Non Metallic cable (Romex)
The wiring is drawn through conduit
Sub Panel Bus BarThe bus bar looks okay
copyright diyinspectionchecklist.com 2018 �43
NOTESThe bus bar is scorched / damaged
The bus bar appears to have been replaced
Sub Panel Infrared ObservationsNo visible issues
Heat in excess observed at one or more connections / breakers / wires
Sub Panel Circuit BreakersCircuit breakers okay
Damaged Circuit breakers
Circuit breakers not approved for this panel board
Circuit breakers scorched
Circuit breakers loose
Circuit breaker is tripped for unknown reasons
AFCI (blue button) recalled
GFCI breaker defective
Circuit breakers amps too large for appliance / circuit / wire
Sub Panel WiringWiring looks okay
Wires scorched
Wires are corroded or deteriorated
Wires loose in panel not terminated
Two or more wires into one breaker
Wire is too small for breaker size
Wire / circuit is not protected by breaker / fuse (direct tap)
Sub Panel Neutral / Grounding BusThe neutral and grounding bus are separate
The sub panel appears to be incorrectly bonded to the equipment panel board
Neutral and grounding conductors are intermixed
Sub Panel Wiring TypeThe wire type is non metallic ( Romex)
copyright diyinspectionchecklist.com 2018 �44
NOTESThe wire type is stranded wire pulled through conduit
The wire type is old Aluminum
The wire type is pre-1984 Non metallic ( Romex)
Sub Panel Grounding SystemThe GROUNDING ELECTRODE CONDUCTOR is present
There is no GROUNDING ELECTRODE CONDUCTOR
The GEC is disconnected
INTERIOR (room) ____________DIY Tips:
1. We suggest printing this section as many times as necessary to accommodate the number of bedrooms, living rooms, dining rooms etc… at your property.
2. In many cases with an occupied property, much of the area within the house is blocked by the occupants belongings. There really isn't much you or any inspector can do about this as many inspectors including yourself are not suggested to move the occupants belongings without permission.
ElectricalSWITCHES
Switches are verified and functional
Unable to verify switch operation (location: __________________________________________)
Damaged switches observe (location: __________________________________________)
Upside-down switches observed (location: __________________________________________)
RECEPTACLES
The receptacles are functional
There are receptacles which do not operate (location: _________________________________)
There are receptacles which are scorched (location: ___________________________________) (*DIY TIP: This is a hazard)
There are receptacles which are cracked (location: ___________________________________) (*DIY TIP: This is a hazard)
There are receptacles which are not switched (1/2 hot required when there are no lights) (location: __________________________________________)
copyright diyinspectionchecklist.com 2018 �45
NOTESAFCI receptacles still “ON” when breaker tripped where applicable (*DIY TIP: This is a hazard)
GFCI receptacles needed / required (*DIY TIP: This is a hazard)
GFCI receptacles defective (*DIY TIP: This is a hazard)
LUMINARIES
Ceiling lights are functional
Ceiling lights with non operational light bulbs
Ceiling lights with missing / damaged globes
Added recessed light fixtures (DIY TIP: Check for permits)
Loose recessed light fixtures
WIRING / CONDUIT
Open junction boxes / exposed wires (*DIY TIP: This is a hazard)
Electrical conduit installed and is not secured
Exposed non metallic wiring AKA romex (*DIY TIP: This is a hazard)
CEILING FAN
Ceiling fan is functional
Ceiling fan is non operational
Ceiling fan wobbles
Ceiling fan is not hard wired
Missing fan blades
CEILING FAN LIGHTS
Lights are functional
Light bulbs non operational
Missing glass globes
Interior DoorsINTERIOR DOORS
copyright diyinspectionchecklist.com 2018 �46
NOTESInterior doors are functional
Interior doors are damaged (location: __________________________________________)
Interior doors are unpainted (location: __________________________________________)
Interior doors are non operational (location: __________________________________________)
Interior door rubs frame / floor
interior door binds
INTERIOR DOOR HARDWARE
Interior door hardware is functional
Double key deadbolts observed ___________________ (*DIY TIP: This is a hazard)
Interior door hardware is damaged / worn
Interior door hardware is non operational
Interior door hardware is loose
Door hinges loose
Exterior DoorsSLIDING GLASS DOORS
Sliding glass doors are functional
Sliding glass doors are difficult to slide
Sliding glass door sill deteriorated
Sliding glass doors are cracked
Glass in door is fogged (condensation in pane)
Door hardware will not lock
Door hardware missing
Door hardware loose
SLIDING GLASS DOOR SCREEN
The Screen door is Okay
The screen door is missing
The screen door is damaged
The screen door will not open
The screen door hardware is worn
copyright diyinspectionchecklist.com 2018 �47
NOTESFRENCH DOORS
French doors are functional
French doors are difficult to slide / open
French doors sill deteriorated
Double key deadbolts observed ___________________ (*DIY TIP: This is a hazard)
French doors are cracked
Glass in French doors are fogged (condensation in pane)
French doors hardware will not lock
French doors hardware missing
French doors hardware loose
Stationary door is non function
MAN DOOR TO EXTERIOR
Man Door Observations
Man door is functional
Man door is damaged
Man door is unpainted
Man door is non operational
Man door is rubs frame / floor
Man door binds
Man door glass cracked / inoperative
MAN DOOR SCREEN
The Screen door is Okay
The screen door is missing
The screen door is damaged
The screen door will not open
The screen door hardware is worn
WindowsWINDOW TYPE: __________________________________copyright diyinspectionchecklist.com 2018 �48
NOTES
WINDOW MATERIALS: VINYL WOOD ALUMINUM
WINDOW OBSERVATIONS
The windows tested were functional
There were cracked windows(*DIY TIP: Have contractor evaluate)
There were inoperable windows
There are damaged sash balancers / cords
There were cracked window frames
Leaking windows observed
Windows were difficult to operate
Inner rubber seal is loose
Double pane glass is fogged / seal damaged
WINDOW SCREENS
The window screens were collectively okay
Worn / damaged screens noted
Missing screens noted
WINDOW HARDWARE
The window hardware is functional
Missing window hardware observed
Worn window hardware observed
There is missing window hardware
WINDOW WEATHERSTRIPPING
The window weatherstripping is functional
There is missing weatherstripping
Window weatherstripping is suggested
FlooringFLOORING MATERIALS: TILE CARPET WOOD LAMINATE OTHER: ____________________copyright diyinspectionchecklist.com 2018 �49
NOTES
The interior flooring is okay
The interior flooring is worn in excess / moderately
Loose carpet observed
Cracked floor tile observed (*DIY TIP: Have contractor evaluate)
Hollow floor tile noted
Floor tile grout missing
The interior flooring is installed in amateurish manner
There is interior flooring which is missing
Wood flooring water damaged (*DIY TIP: Have contractor evaluate)
Wood flooring is buckled
Open gaps in wood flooring
Vinyl flooring is in need of sealant
Loose vinyl flooring
Seal vinyl flooring connection to the bathtub
Damaged vinyl flooring
Stained vinyl flooring
WallsThe interior walls were in generally good condition
Holes were observed within interior walls
Stains were observed in interior walls (*DIY TIP: Ask sellers of any knowledge of previous damage)
Mold was observed (*DIY TIP: Have contractor evaluate)
Cracks noted in the walls (1/8” 1/4” 1/2”) (*DIY TIP: Have contractor evaluate)
Moisture damaged wall covering noted (*DIY TIP: Have contractor evaluate)
CeilingsThe ceilings were functional
There were stains in the interior ceilings(*DIY TIP: Ask sellers of any knowledge of previous damage)
copyright diyinspectionchecklist.com 2018 �50
NOTESThere were popcorn ceiling materials (*DIY TIP: This material has been known to contain Asbestos - testing is suggested)
There were prior repairs noted (*DIY TIP: Ask sellers of any knowledge of previous damage)
Holes in ceilings noted
Cracks observed in the ceilings (1/8” 1/4” 1/2”) (*DIY TIP: Have contractor evaluate)
EgressEGRESS WINDOWS AND DOORS
All conditions listed below (if checked) require an additional inspection by a professional of this trade
All conditions are considered a hazard if checked
There is only one door for entry and exit
The window sills are higher than 44” from the floor
The basement does not have any operable windows or doors that leads to the exterior
The window in the basement does not allow for safe exit to the exterior of the building
The window well in the basement does not possess a ladder
Interior BarThe bar faucet, sink and plumbing was functional
The bar faucet was non functional (*DIY TIP: Have contractor evaluate)
The bar faucet hot / cold water is non functional (*DIY TIP: Have contractor evaluate)
The bar plumbing leaks (*DIY TIP: Have contractor evaluate)
The drain trap is an “S” trap
CabinetryThe cabinet is functional
The cabinet is damaged
The cabinet is not secured to the wall
The cabinet doors are loose / need adjustment
There are missing doors at the cabinet
Sky-LightsThe skylight appear functional
The skylight is cracked (*DIY TIP: Have contractor evaluate)copyright diyinspectionchecklist.com 2018 �51
NOTESStains were observed under the skylight (*DIY TIP: Ask sellers of any knowledge of previous damage) (*DIY TIP: Have contractor evaluate)
STAIRSStair Railing
The stair railing was acceptable
The stair railing opening is wider than 6” (*DIY TIP: This is a hazard)
The railing is damaged (*DIY TIP: This is a hazard)
The railing is loose (*DIY TIP: This is a hazard)
The balusters are loose (*DIY TIP: This is a hazard)
The railing is too low (*DIY TIP: This is a hazard)
The railing is too high (*DIY TIP: This is a hazard)
Stair TreadsThe stair treads were okay
The stair treads are not uniform in their width (*DIY TIP: This is a hazard)
The stair treads are not uniform in their tread projection (*DIY TIP: This is a hazard)
The stair treads are not uniform in their height (*DIY TIP: This is a hazard)
Loose stair treads were observed (*DIY TIP: This is a hazard)
LAUNDRYGeneral CommentsLAUNDRY AREA LOCATION: INTERIOR / EXTERIOR
Supply pipingThe supply piping is in acceptable condition
The angle stop on the hot / cold side was corroded
The angle stop hot / cold was leaking (*DIY TIP: Have contractor evaluate)
The hot / cold water supply was not functional (*DIY TIP: Have contractor evaluate)copyright diyinspectionchecklist.com 2018 �52
NOTES
WasteThe drain line was functional
The drain line was blocked (*DIY TIP: Have contractor evaluate)
Gas SupplyThe gas valve is okay
The gas valve is leaking (*DIY TIP: This is a hazard)
The gas valve handle is damaged (*DIY TIP: This is a hazard)
Electrical 120V SUPPLY
The Receptacle is okay
The receptacle is not grounded (*DIY TIP: This is a hazard)
The receptacle has reversed polarity (*DIY TIP: This is a hazard)
The receptacle is non operational (*DIY TIP: Have contractor evaluate)
The receptacle is damaged (*DIY TIP: This is a hazard)
The cover plate is missing (*DIY TIP: This is a hazard)
240V SUPPLY
The 240 Receptacle is okay
The 240 receptacle is not grounded (*DIY TIP: This is a hazard)
The 240 receptacle is non operational (*DIY TIP: Have contractor evaluate)
The 240 receptacle is damaged (*DIY TIP: This is a hazard)
The cover plate is missing (*DIY TIP: This is a hazard)
Dryer DuctThe dryer duct is okay
The dryer duct appears blocked (*DIY TIP: This is a hazard)
The dryer duct is too long (*DIY TIP: Have contractor evaluate)
The dryer duct is not made of rigid metal (*DIY TIP: Have contractor evaluate)
The dryer duct vents vertically with no clean out (*DIY TIP: This is a hazard)
The dryer duct has screws which penetrate the duct
Cabinetry
copyright diyinspectionchecklist.com 2018 �53
NOTESThe cabinet is functional
The cabinet is damaged
The cabinet is not secured to the wall
The cabinet doors are loose / need adjustment
There are missing doors at the cabinet
Combustion / Make-up AirThe combustion / make up air is okay
The combustion / make up air is insufficient (*DIY TIP: This is a hazard)
Room VentilationThe room ventilation is okay
The room ventilation non functional (*DIY TIP: This is a hazard)
The room ventilation fan is noisy (*DIY TIP: Have contractor evaluate)
The room ventilation fan is dirty (*DIY TIP: This is a hazard)
The room ventilation fan is loose / hanging from the ceiling (*DIY TIP: Have contractor evaluate)
Washing Machine PanThe washing machine pan is okay
The washing machine pan is damaged
The washing machine pan is needed
Laundry SinkThe laundry sink faucet, sink and plumbing was functional
The laundry sink faucet was non functional (*DIY TIP: Have contractor evaluate)
The laundry sink faucet hot / cold water is non functional (*DIY TIP: Have contractor evaluate)
The laundry sink plumbing leaks (*DIY TIP: Have contractor evaluate)
The hot and cold water lines are reversed (*DIY TIP: Have contractor evaluate)
ElectricalSWITCHES
Switches are verified and functional
copyright diyinspectionchecklist.com 2018 �54
NOTESUnable to verify switch operation (*DIY TIP: Have contractor evaluate)
Damaged switches observe (*DIY TIP: This is a hazard)
Upside-down switches observed
RECEPTACLES
The receptacles are functional
There are receptacles which do not operate (*DIY TIP: Have contractor evaluate)
There are receptacles which are scorched (*DIY TIP: This is a hazard)
There are receptacles which are cracked (*DIY TIP: This is a hazard)
There are receptacles which are not switched (1/2 hot required when there are no lights) (*DIY TIP: Have contractor evaluate)
AFCI receptacles still “ON” when breaker tripped where applicable (*DIY TIP: This is a hazard)
GFCI receptacles needed / required (*DIY TIP: This is a hazard)
GFCI receptacles defective (*DIY TIP: This is a hazard)
LUMINARIES
Ceiling lights are functional
Ceiling lights with non operational light bulbs
Ceiling lights with missing / damaged globes
Added recessed light fixtures (*DIY TIP: Check for a building permit)
Loose recessed light fixtures
KITCHENGeneral Comments
The kitchen was remodeled. Request documentation or permits for any work performed. (*DIY TIP: Check for a building permit)
ElectricalSWITCHES
Switches are verified and functional
Unable to verify switch operation
Damaged switches observe (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �55
NOTESUpside-down switches observed
RECEPTACLES
The receptacles are functional
There are receptacles which do not operate
No GROUND FAULT receptacle in Island (*DIY TIP: This is a hazard)
Island receptacle is more than 12” from the surface (*DIY TIP: This is a hazard)
Island receptacle counter top extends more than 6” past the receptacle (*DIY TIP: This is a hazard)
There are receptacles which are scorched (*DIY TIP: This is a hazard)
There are receptacles which are cracked (*DIY TIP: This is a hazard)
There are receptacles which are not switched (*DIY TIP: Check for a building permit)
GFCI receptacles needed / required (*DIY TIP: This is a hazard)
GFCI receptacles defective (*DIY TIP: This is a hazard)
LUMINARIES
Ceiling lights are functional
Ceiling lights with non operational light bulbs (*DIY TIP: This is a hazard)
Ceiling lights with missing / damaged globes
Added recessed light fixtures (*DIY TIP: Check for a building permit)
Loose recessed light fixtures
WIRING / CONDUIT
Open junction boxes / exposed wires (*DIY TIP: This is a hazard)
Electrical conduit installed and is not secured (*DIY TIP: Check for a building permit)
Exposed non metallic wiring AKA romex (*DIY TIP: This is a hazard)
CEILING FAN
Ceiling fan is functional
Ceiling fan is non operational
Added ceiling fans (*DIY TIP: Check for a building permit)
Ceiling fan wobbles
Ceiling fan is not hard wired (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �56
NOTESMissing fan blades
CEILING FAN LIGHTS
Lights are functional
Light bulbs non operational (*DIY TIP: Have contractor evaluate)
Missing globes
Countertop COUNTERTOP MATERIALS: TILE GRANITE SOLID SURFACE FORMICA CONCRETE
Countertop ObservationsThe countertop materials were in acceptable condition
The countertop material possess cracks / chips / damage
The countertop materials possess raised / lower seams
The countertop material is loose
The countertop material missing
There was no backsplash present
Missing backsplash materials noted
Kitchen SinkSINK
The kitchen sink is Okay
The kitchen sink is cracked
The kitchen sink needs caulking between sink and countertop
The kitchen sink is rusted
The kitchen sink is chipped
FAUCETThe faucet is okay
The faucet drips
The faucet leaks at the stem
The faucet is non functional
The faucet is loose
The faucet only provides hot / cold water (*DIY TIP: Have contractor evaluate)
The hot and cold water lines are reversed (*DIY TIP: Have contractor evaluate)copyright diyinspectionchecklist.com 2018 �57
NOTESDRAIN / TRAP
The drain trap is okay
The drain trap is corroded as if to suggest a current or prior leak
The drain trap is an “S” trap (*DIY TIP: Have contractor evaluate)
The drain trap arm is too long / too short to weir (*DIY TIP: Have contractor evaluate)
Crown venting is noted here
Island drain is not vented correctly (*DIY TIP: Have contractor evaluate)
ANGLE-STOPS AND CONNECTORS
The angel stop is okay
The angel stop is / are corroded (*DIY TIP: Have contractor evaluate)
The angel stop is leaking hot / cold (*DIY TIP: Have contractor evaluate)
The angel stop is missing a handle hot / cold (*DIY TIP: Have contractor evaluate)
Garbage DisposalThe garbage disposal is okay
The garbage disposal is non operational (*DIY TIP: Have contractor evaluate)
The garbage disposal noisy (*DIY TIP: Have contractor evaluate)
The garbage disposal is leaking (*DIY TIP: Have contractor evaluate)
The garbage disposal is missing (*DIY TIP: Have contractor evaluate)
The garbage disposal is frozen (*DIY TIP: Have contractor evaluate)
The garbage disposal is missing a splash guard
Kitchen CabinetsThe kitchen cabinets were okay
The kitchen cabinets were missing doors / drawers
The kitchen cabinets need adjustment
The kitchen cabinets were damaged
The kitchen cabinets were peeling
The kitchen cabinets were missing hardware
The kitchen cabinets in overall poor condition (*DIY TIP: Have contractor evaluate)
The base under the kitchen sink was damaged
The base under the kitchen sink has mold (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �58
NOTESThe base under the kitchen sink needs to be replaced (*DIY TIP: Have contractor evaluate)
The base under the kitchen sink was missing (*DIY TIP: Have contractor evaluate)
Gas / Electric Cook topThe cooktop was functional
The cooktop tilts forward and is not secured (*DIY TIP: This is a hazard)
Burners were not functional on the cook top RR RF LR LF
Grates were missing from cook top
Missing knobs were noted
The electric control panel was damaged (*DIY TIP: Have contractor evaluate)
Gas off not tested
Igniter was damaged non functional (*DIY TIP: Have contractor evaluate)
NUMBER OF OVENS: 1 2 3 4
Gas / Electric OvenThe ovens are / is functional
The upper / lower oven was non operational (*DIY TIP: Have contractor evaluate)
The upper / lower oven door hinge was damaged (*DIY TIP: Have contractor evaluate)
The upper / lower oven glass is damaged (*DIY TIP: Have contractor evaluate)
The upper / lower oven door does not seal
The upper / lower oven was light was not functional
The upper / lower oven control panel was damaged / non functional (*DIY TIP: Have contractor evaluate)
The upper / lower oven was failed to heat (*DIY TIP: Have contractor evaluate)
Exhaust Ventilation / LightThe exhaust fan and light were functional
The exhaust fan was non operational (*DIY TIP: Have contractor evaluate)
The exhaust fan was very noisy (*DIY TIP: Have contractor evaluate)
The exhaust fan was missing filter
The exhaust fan does not duct to the exterior (*DIY TIP: Have contractor evaluate)
The light was non operational
copyright diyinspectionchecklist.com 2018 �59
NOTESThe light was flickering
The light was missing not tested
DishwasherThe dishwasher is functional
The dishwasher is leaking (*DIY TIP: Have contractor evaluate)
The dishwashers seal is old / worn
The dishwasher is loose /not secured
The dishwasher racks are rusted damaged
The dishwasher is very noisy (*DIY TIP: Have contractor evaluate)
The dishwasher is leaking from the air gap device (*DIY TIP: Have contractor evaluate)
The dishwasher is missing an air gap device (*DIY TIP: Have contractor evaluate)
The dishwasher is non operational
The dishwasher is tripping the circuit (*DIY TIP: Have contractor evaluate)
The dishwasher display is damaged (*DIY TIP: Have contractor evaluate)
BATHROOMS(*Additional pages can be printed from our website for individual bathrooms)
ElectricalSWITCHES
Switches are verified and functional
Unable to verify switch operation (*DIY TIP: Have contractor evaluate)
Damaged switches observe (*DIY TIP: This is a hazard)
Upside-down switches observed
RECEPTACLES
The receptacles are functional
There are receptacles which do not operate (*DIY TIP: Have contractor evaluate)
There are receptacles which are scorched (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �60
NOTESThere are receptacles which are cracked (*DIY TIP: This is a hazard)
There are receptacles which are not switched (1/2 hot required when there are no lights)
AFCI receptacles still “ON” when breaker tripped where applicable (*DIY TIP: This is a hazard)
GFCI receptacles needed / required (*DIY TIP: This is a hazard)
GFCI receptacles defective (*DIY TIP: This is a hazard)
LUMINARIES
Ceiling lights are functional
Ceiling lights with non operational light bulbs
Ceiling lights with missing / damaged globes
Added recessed light fixtures (*DIY TIP: Check for a building permit)
Loose recessed light fixtures
WIRING / CONDUIT
Open junction boxes / exposed wires (*DIY TIP: This is a hazard)
Electrical conduit installed and is not secured
Exposed non metallic wiring AKA romex (*DIY TIP: This is a hazard)
ToiletThe toilet was functional
The toilet is not low flow
The toilet runs continually
The toilet bowl / tank / base is cracked
The toilet is loose at the tank / floor
The toilet does not flush properly
SinkThe bathroom sink is Okay (Double L / R)
The bathroom sink is cracked (Double L / R)
The bathroom sink needs caulking between sink and countertop (Double L / R)
The bathroom sink is rusted (Double L / R)
The bathroom sink is chipped (Double L / R)
FAUCET
copyright diyinspectionchecklist.com 2018 �61
NOTESThe faucet is okay (Double L / R)
The faucet drips (Double L / R)
The faucet leaks at the stem (Double L / R)
The faucet is non functional (Double L / R)
The faucet is loose (Double L / R)
The faucet only provides hot / cold water (Double L / R) (*DIY TIP: Have contractor evaluate)
The hot and cold water lines are reversed (Double L / R)
DRAIN / TRAP
The drain trap is okay (Double L / R)
The drain trap is corroded as if to suggest a current or prior leak (Double L / R)
The drain trap is an “S” trap (Double L / R) (*DIY TIP: Have contractor evaluate)
The drain trap arm is too long / too short to weir (Double L / R) (*DIY TIP: Have contractor evaluate)
Crown venting is noted here (Double L / R)
ANGLE-STOPS AND CONNECTORS
The angel stop is okay (Double L / R)
The angel stop is / are corroded (Double L / R)
The angel stop is leaking hot / cold (Double L / R) (*DIY TIP: Have contractor evaluate)
The angel stop is missing a handle hot / cold (Double L / R)
Ventilation FanThe ventilation fan is operational
The ventilation fan is noisy (*DIY TIP: Have contractor evaluate)
The ventilation fan is non operational (*DIY TIP: Have contractor evaluate)
The ventilation fan is loose at the ceiling
The ventilation fan is missing the cover
The ventilation fan needs to be cleaned
Bathtub / Shower enclosure
copyright diyinspectionchecklist.com 2018 �62
NOTESThe Bathtub / Shower enclosure is functional
The Bathtub / Shower enclosure chipped / cracked
The Bathtub / Shower enclosure drains slowly (*DIY TIP: Have contractor evaluate)
The Bathtub / Shower enclosure leaks
The Bathtub / Shower enclosure water valves leak (*DIY TIP: Have contractor evaluate)
The Bathtub / Shower enclosure water valves are reversed (*DIY TIP: Have contractor evaluate)
The Bathtub / Shower enclosure water valves were non operational hot / cold side (*DIY TIP: Have contractor evaluate)
The Bathtub / Shower enclosure produce low water volume hot / cold side (*DIY TIP: Have contractor evaluate)
The Bathtub / Shower enclosure water valve(s) / handle(s) are loose
The Bathtub / Shower enclosure water valve handle is missing
The Bathtub / Shower enclosure door is missing / damaged / off track
The Bathtub / Shower enclosure is heavily worn including chips and cracks in fiberglass
The Bathtub / Shower enclosure have missing / cracked tile
The Bathtub / Shower enclosure needs caulking throughout
The tile shower pan leaks (*DIY TIP: Have contractor evaluate)
Hydromassage BathtubThe hydromassage bathtub jets were functional
The hydromassage bathtub is not installed on a solid substrate (*DIY TIP: Have contractor evaluate)
The hydromassage bathtub does not possess a GROUND FAULT for protection (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
The hydromassage bathtub GROUND FAULT is defective (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
The hydromassage bathtub is not on a dedicated circuit (*DIY TIP: Have contractor evaluate)
The GROUND FAULT is too far from the hydromassage bathtub (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
The hydromassage bathtub is not bonded (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
The hydromassage bathtub air switch is non functional (*DIY TIP: Have contractor evaluate)
The hydromassage bathtub air switch is temperamental
The hydromassage bathtub jets low volume (*DIY TIP: Have contractor evaluate)copyright diyinspectionchecklist.com 2018 �63
NOTESEyeballs missing
The hydromassage bathtub jets are non functional (*DIY TIP: Have contractor evaluate)
The hydromassage bathtub is leaking at supply lines (*DIY TIP: Have contractor evaluate)
The hydromassage bathtub was added (*DIY TIP: Check for a building permit)
VanityThe vanity was functional
The vanity was missing
The vanity was added
The vanity was missing doors
The vanity was missing countertop
There is no backsplash
Damaged countertop
ATTICATTIC ACCESS LOCATION: _____________________
Attic AccessThe attic was fully accessible
The attic was not accessible at all
The attic was accessible only on the furnace platform
The attic was only partially accessible
The attic access was limited due to the occupants belongings
Attic InsulationThe attic is insulated with:
Fiberglass batt | Mineral (rock or slag) wool | Cellulose | Vermiculite | Urea Formaldehyde Foam | Asbestos
The attic was insulated with ___________ inches of insulation
There was poor coverage (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �64
NOTESThere was loose / missing insulation (*DIY TIP: Have contractor evaluate)
The insulation appears to be rodent damaged (urine / feces) (*DIY TIP: Have contractor evaluate)
The insulation is compressed (*DIY TIP: Have contractor evaluate)
The insulation may be a hazardous material (*DIY TIP: Have contractor evaluate)
The insulation is cellulose pre 1979 (may be flammable) (*DIY TIP: Have contractor evaluate)
Attic FramingThe attic framing appears to be in generally good condition
The attic framing has stains consistent with potential leaking (*DIY TIP: Have contractor evaluate)
The attic framing is moisture damaged (*DIY TIP: Have contractor evaluate)
The attic framing has been structurally modified (*DIY TIP: Have contractor evaluate & check for permits)
The attic framing has been removed or otherwise modified (*DIY TIP: Have contractor evaluate & check for permits)
The attic framing appears to have been in a fire (*DIY TIP: Have contractor evaluate & check for permits)
The attic framing appears to have been repaired (*DIY TIP: Have contractor evaluate & check for permits)
The attic framing appears undersized for the roofing material installed (*DIY TIP: Have contractor evaluate)
There are damaged wood members within the attic (*DIY TIP: Have contractor evaluate)
Attic VentilationThe attic ventilation is functional
The attic ventilation is marginal (*DIY TIP: Have contractor evaluate)
The attic ventilation is missing (*DIY TIP: Have contractor evaluate)
The attic ventilation needs improving (*DIY TIP: Have contractor evaluate)
The attic ventilation fan is inoperable (*DIY TIP: Have contractor evaluate)
The attic ventilation fan is damaged (*DIY TIP: Have contractor evaluate)
Attic ElectricalThe attic electrical is functional
There are loose wires in the attic (*DIY TIP: This is a hazard)
There are open junction boxes in the attic (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �65
NOTESThere is loose “Romex” NM cable in the attic
There are recessed lights too close to insulation or wood (*DIY TIP: This is a hazard)
Wiring appears to have been damaged by rodents (*DIY TIP: This is a hazard)
Attic Exhaust DuctsThe attic exhaust ducts appear functional
The attic exhaust ducts need to extend to the exterior (*DIY TIP: Have contractor evaluate)
The attic exhaust ducts are crushed
The attic exhaust ducts are disconnected from fan (*DIY TIP: Have contractor evaluate)
Factory Built Chimney Flue / Fire StopThe fireplace vent / fires stop is functional
The fireplace vent is damaged (*DIY TIP: This is a hazard)
The fireplace vent is too close to wood or insulation (*DIY TIP: This is a hazard)
The fireplace vent is disconnected (*DIY TIP: This is a hazard)
The fireplace fire stop is missing (*DIY TIP: This is a hazard)
The fireplace fire stop is incomplete (*DIY TIP: This is a hazard)
The fireplace fire stop is not a listed component (*DIY TIP: This is a hazard)
Masonry Chimney ObservationsThe masonry chimney appears functional
The masonry chimney bricks need re-pointing (*DIY TIP: This is a hazard)
The masonry chimney is too close to wood (*DIY TIP: This is a hazard)
The masonry chimney is not strapped in accordance with building code (*DIY TIP: Have contractor evaluate)
The masonry chimney appears damaged (*DIY TIP: This is a hazard)
The masonry chimney appears modified or repaired (*DIY TIP: Have contractor evaluate & check for permits)
Attic Separation wall (Condo / Town-house)The attic separation wall is functional
The attic separation wall is damaged (*DIY TIP: Have contractor evaluate)
The attic separation wall possesses holes (*DIY TIP: Have contractor evaluate)
The attic separation wall is missing or incomplete (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �66
NOTES
Heating System FORCED AIR UNITLOCATION:AGE:
Heating System ObservationsThe heating system was functional
The heating system was not operational (*DIY TIP: Have contractor evaluate)
The gas was off
The furnace is red-tagged (*DIY TIP: Have contractor evaluate)
The furnace is a floor furnace and needs to be inspected by a professional (*DIY TIP: Have contractor evaluate)
Combustion ChamberThe Combustion chamber is clean
The combustion chamber is filled with rust and is deteriorated (*DIY TIP: Have contractor evaluate)
Cracks are visible within the heat exchangers (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
The unit appears to draft improperly (*DIY TIP: This is a hazard)
“Roll-out” was observed upon starting the furnace (*DIY TIP: This is a hazard)
The flame pattern is erratic - further evaluation is needed (*DIY TIP: Have contractor evaluate)
Water appears to be leaking into the combustion chamber (*DIY TIP: Have contractor evaluate)
VentingThe vent is functional
The vent is too close to combustion material (*DIY TIP: This is a hazard)
The vent is disconnected (*DIY TIP: This is a hazard)
The vent is incorrectly sloped (*DIY TIP: This is a hazard)
The vent is deteriorated / rusted (*DIY TIP: Have contractor evaluate)
The vent is stained (roof leaking) (*DIY TIP: Have contractor evaluate)
There is single wall vent within the attic (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �67
NOTESThere is Transite installed here (*DIY TIP: Have contractor evaluate)
There is a gap from the 3” to 4” connection (*DIY TIP: This is a hazard)
The draft inducer is very noisy (*DIY TIP: Have contractor evaluate)
Fuel SupplyThe fuel supply is operational
The fuel supply does not possess a sediment trap (*DIY TIP: Have contractor evaluate)
The fuel supply valve leaks (*DIY TIP: This is a hazard)
The fuel supply possess aluminum or brass flex gas line
The fuel supply flex enters through the side wall of the furnace cabinet (*DIY TIP: Have contractor evaluate)
The fuel supply flex line is kinked
Combustion / Make up AirThe supply air to the furnace is acceptable
The supply air to the furnace is limited (*DIY TIP: Have contractor evaluate) (*DIY TIP: This is a hazard)
The supply air to the furnace is missing
The supply air to the furnace is missing screens
The supply air to the furnace possess attic screens
Evaporative CoilThe Evaporative coil is acceptable
The Evaporative coil is new
The Evaporative coil is leaking water (*DIY TIP: Have contractor evaluate)
The Evaporative coil is leaking air
The Evaporative coil is deteriorated (*DIY TIP: Have contractor evaluate)
Circulating FanThe circulating fan is functional
The circulating fan is noisy
The circulating fan out of balance
The circulating fan is very dirty
The circulating fas belt is loose
copyright diyinspectionchecklist.com 2018 �68
NOTES
Condensate Drain(s)The condensate drains are functional
The condensate drain (primary) / (Secondary) is clogged (*DIY TIP: Have contractor evaluate)
The condensate drain leaks from the secondary (*DIY TIP: Have contractor evaluate)
The condensate drain pan is filled with water (*DIY TIP: Have contractor evaluate)
The secondary condensate drains are not installed over a window (*DIY TIP: Have contractor evaluate)
The condensate drain (primary) is kinked (*DIY TIP: Have contractor evaluate)
The condensate drains not installed (*DIY TIP: Have contractor evaluate)
The condensate drains into a pump - ensure the pump is functional
The condensate drains termination is not visible or cannot be located (*DIY TIP: Have contractor evaluate)
Thermostat(s)The thermostat is functional
The thermostat is loose
The thermostat is non operational (*DIY TIP: Have contractor evaluate)
The thermostat is defective
The thermostat is in the wrong place (*DIY TIP: Have contractor evaluate)
Return AirThe return air base is functional
The return air base needs to be sealed (*DIY TIP: Have contractor evaluate)
The return air base is under the furnace closet door
The return air is in the wrong location
The house is 2 story with only one return air (*DIY TIP: Have contractor evaluate)
The return air is located too close to the kitchen or laundry room (*DIY TIP: Have contractor evaluate)(*DIY TIP: This is a hazard)
AIR CONDITIONERSIZE: 1 TON 2 TONS 3 TONS 4 TONS 5 TONS AGE: ___________
copyright diyinspectionchecklist.com 2018 �69
NOTES
General ObservationsThe air condition system appears to be functional
The condenser is newer (ask about installation by professional / permits)
The condenser was moved - (check for permits)
Not accessible for inspection
The condenser is at the end of its life (*DIY TIP: Have contractor evaluate)
The condenser is out of level
The condenser is under / over sized for square footage (*DIY TIP: Have contractor evaluate)
The condenser is turning on and off repeatedly (*DIY TIP: Have contractor evaluate)
The coil is damaged (fins are smashed)
The condenser is very dirty
The condenser is not secured to the slab / 3” from grade
The condenser is too close to adjacent walls or plants (12”)
The condenser is too close to irrigation
The condenser is too close to the pool (*DIY TIP: Have contractor evaluate)
The condenser is too close to the dryer vent termination (*DIY TIP: Have contractor evaluate)
The condensers fan is imbalanced
The condenser is making unusual noises (*DIY TIP: Have contractor evaluate)
ElectricalThe electrical is functional
The sub panel needs to be sealed to the wall
The sub panel is missing its inner cover - exposed wiring (*DIY TIP: This is a hazard)
The sub panel is not secured to the wall
The sub panel is located behind the condenser - hazardous location (*DIY TIP: This is a hazard)
The sub panel is missing knockouts (*DIY TIP: This is a hazard)
Conduit is disconnected from the sub panel / condenser (*DIY TIP: This is a hazard)
The sub panel possess fuses which are too large for the condenser (*DIY TIP: This is a hazard)
The sub panel is missing fuses
Refrigerant LinesThe refrigerant lines are acceptable
copyright diyinspectionchecklist.com 2018 �70
NOTESThe refrigerant lines are missing insulation
The refrigerant lines possess deteriorated foam
The refrigerant lines are run underground (*DIY TIP: Have contractor evaluate)
The refrigerant lines are lying on grade
The refrigerant lines are uninsulated inside the wall (*DIY TIP: Have contractor evaluate)
The refrigerant lines are not supported properly
The copper refrigerant lines are connected to galvanized straps
Temperature DifferentialThe temperature differential is acceptable (18 - 21 degrees)
The temperature differential is unacceptable
REGISTERS AND DUCTSFlexible Ducts
The flexible ducts are acceptable
The flexible ducts have damaged vapor barriers
The flexible ducts are disconnected
The flexible ducts are kinked / crushed (*DIY TIP: Have contractor evaluate)
Sealant is needed at a couple / multiple connections
The flexible ducts are installed incorrectly (*DIY TIP: Have contractor evaluate)
The flexible ducts are newer replaced (*DIY TIP: Ask the seller of any knowledge of this)
Asbestos DuctsThe Asbestos ducts are in-tact - undisturbed
The Asbestos ducts are damaged - friable (*DIY TIP: This is a hazard)
Rigid Fiberglass / Metal DuctsThe rigid fiberglass / metal ducts are acceptable
The rigid fiberglass / metal ducts are unwrapped / damaged / split
copyright diyinspectionchecklist.com 2018 �71
NOTESThe rigid fiberglass / metal ducts are crushed (*DIY TIP: Have contractor evaluate)
The rigid fiberglass / metal ducts are disconnected (*DIY TIP: Have contractor evaluate)
Thermostatically Controlled DampersThe Thermostatically Controlled Dampers work as intended
The Thermostatically Controlled Dampers leak (*DIY TIP: Have contractor evaluate)
The Thermostatically Controlled Dampers are non operational (*DIY TIP: Have contractor evaluate)
RegistersThe registers are acceptable
The registers are non operational in the _______________________ room (*DIY TIP: Have contractor evaluate)
The registers have very low volume in the ______________________ room (*DIY TIP: Have contractor evaluate)
There were register covers missing
SWIMMING POOL AND SPAOPERATION MODE - The pool was on / off at the time of the inspection
Water Fill and OverflowFILLER TYPE
The filler valve is: Automatic | Manual
WATER FILLER VALVE
The water filler valve is operational
The water filler valve is leaking
The water filler valve non functional (*DIY TIP: Have contractor evaluate)
AUTO FILLER
The auto fill valve is functional
The auto fill valve float is damaged / missing (*DIY TIP: Have contractor evaluate)
The auto fill valve is leaking
copyright diyinspectionchecklist.com 2018 �72
NOTESThe auto fill valve is stuck
OVERFLOW DRAIN
The overflow drain is present
The overflow drain is missing
FILLED BY WATER HOSE
The pool is filled by a water hose
Disinfectant typeCHLORINE DISINFECTANT
SALT DISINFECTANT
OTHER DISINFECTANT TYPE___________________________________
Pool TileThe pool tile is functional
The pool tile is missing
The pool tile is cracked
The pool tile is loose
The pool tile is calcium stained
The pool tile is new or replaced
Pools Interior Finish MaterialPLASTER FINISH
PEBBLE FINISH
CopingCOPING MATERIAL
The coping is concrete
The coping is stone or brick
copyright diyinspectionchecklist.com 2018 �73
NOTESCOPING OBSERVATIONS
The coping is functional
The coping is cracked
The coping is raised / settled
The coping is loose
The coping is missing
The coping is otherwise damaged
Elastomeric sealant is needed between pool coping and deck
Pool DeckDECK MATERIAL
The pool deck is concrete / stone / brick / pavers / missing / other ______________________
DECK OBSERVATIONS
The pool deck is functional
The pool deck is cracked - large / small
The pool deck is settled or raised (*DIY TIP: Have contractor evaluate)
The pool deck is sloped towards the pool (*DIY TIP: Have contractor evaluate)
The pool deck is sloped towards the house (*DIY TIP: Have contractor evaluate)
SkimmerThe skimmer is functional
The skimmer is cracked (*DIY TIP: Have contractor evaluate)
The skimmer needs to be sealed at the top connection to deck (*DIY TIP: Have contractor evaluate)
The skimmer has only one port
The skimmer is older concrete type (*DIY TIP: Have contractor evaluate)
The skimmer is older metal type (*DIY TIP: Have contractor evaluate)
The skimmer is missing its weir gate
Pool DrainsThe swimming pool drains are anti entrapment type and functional
The swimming pool drains are non anti entrapment type (*DIY TIP: This is a hazard)
The swimming pool drains are less than 3 feet apart
copyright diyinspectionchecklist.com 2018 �74
NOTESThe swimming pool drains are cracked / damaged (*DIY TIP: This is a hazard)
The swimming pool drains are missing (*DIY TIP: This is a hazard)
The swimming pool drains are sealed / missing (*DIY TIP: Have contractor evaluate)
Cleaner MachineThe cleaner is present and functional
The cleaner is not moving (*DIY TIP: Have contractor evaluate)
The cleaner is damaged
The cleaner is in need of repair (*DIY TIP: Have contractor evaluate)
The cleaner is piped into the skimmer
LightingThe Lighting is GROUND FAULT protected and functional
The Lighting is not GROUND FAULT protected (*DIY TIP: This is a hazard)
The Lighting GROUND FAULT is defective (*DIY TIP: This is a hazard)
The Lighting is missing a switch (*DIY TIP: Have contractor evaluate)
The Lighting was non operational pool / spa (*DIY TIP: This is a hazard)
The Light(s) is / are missing (*DIY TIP: Have contractor evaluate)
Diving Board / Diving RockThe diving board present is functional
The diving board is cracked / fiberglass fibers showing (*DIY TIP: This is a hazard)
The diving board is loose (*DIY TIP: Have contractor evaluate)
The diving board bolts are rusted / deteriorated (*DIY TIP: Have contractor evaluate)
The diving board is not bonded (*DIY TIP: This is a hazard)
SlideThe slide present is functional
The slide is cracked / fiberglass fibers showing (*DIY TIP: This is a hazard)
The slide is loose (*DIY TIP: This is a hazard)
The slide bolts are rusted / deteriorated
The slide is not bonded (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �75
NOTES
Ladder / RailingThe ladder or railing is functional
The ladder or railing is loose (*DIY TIP: This is a hazard)
The ladder or railing is rusted
The ladder or railing is not bonded (*DIY TIP: This is a hazard)
Pool PumpsCIRCULATION PUMP
The pump is bonded and functional
The pump is non operational (*DIY TIP: Have contractor evaluate)
The pump is not bonded (*DIY TIP: This is a hazard)
The pump is not secured to the slab
The pump leaks at the pump / motor connection (*DIY TIP: Have contractor evaluate)
The pump leaks at the lid
The pump basket is damaged / missing
The pump cavitates (*DIY TIP: Have contractor evaluate)
The pump is leaking at the pipe connection in / out (*DIY TIP: Have contractor evaluate)
The front pipe is too short into the pump
The pump wiring is loose / detached (*DIY TIP: This is a hazard)
The pump does not possess a shutoff switch at the equipment (*DIY TIP: Have contractor evaluate)
SPA JET PUMP
The pump is bonded and functional
The pump is non operational (*DIY TIP: Have contractor evaluate)
The pump is not bonded (*DIY TIP: This is a hazard)
The pump is not secured to the slab
The pump leaks at the pump / motor connection (*DIY TIP: Have contractor evaluate)
The pump leaks at the lid
The pump basket is damaged / missing
The pump cavitates (*DIY TIP: Have contractor evaluate)
The pump is leaking at the pipe connection in / out (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �76
NOTESThe front pipe is too short into the pump
The pump wiring is loose / detached (*DIY TIP: This is a hazard)
The pump does not possess a shutoff switch at the equipment (*DIY TIP: Have contractor evaluate)
WATER FEATURE PUMP
The pump is bonded and functional
The pump is non operational (*DIY TIP: Have contractor evaluate)
The pump is not bonded (*DIY TIP: This is a hazard)
The pump is not secured to the slab
The pump leaks at the pump / motor connection (*DIY TIP: Have contractor evaluate)
The pump leaks at the lid
The pump basket is damaged / missing
The pump cavitates (*DIY TIP: Have contractor evaluate)
The pump is leaking at the pipe connection in / out (*DIY TIP: Have contractor evaluate)
The front pipe is too short into the pump
The pump wiring is loose / detached (*DIY TIP: This is a hazard)
The pump does not possess a shutoff switch at the equipment (*DIY TIP: Have contractor evaluate)
OTHER PUMP PUMPS USE ______________________
The pump is bonded and functional
The pump is non operational (*DIY TIP: Have contractor evaluate)
The pump is not bonded (*DIY TIP: This is a hazard)
The pump is not secured to the slab
The pump leaks at the pump / motor connection (*DIY TIP: Have contractor evaluate)
The pump leaks at the lid
The pump basket is damaged / missing
The pump cavitates (*DIY TIP: Have contractor evaluate)
The pump is leaking at the pipe connection in / out
The front pipe is too short into the pump
The pump wiring is loose / detached (*DIY TIP: This is a hazard)
The pump does not possess a shutoff switch at the equipment (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �77
NOTESDIRECT PRESSURE PUMP
The pump is bonded and functional
The pump is non operational (*DIY TIP: Have contractor evaluate)
The pump is not bonded (*DIY TIP: This is a hazard)
The pump is not secured to the slab
The pump leaks at the pump / motor connection (*DIY TIP: Have contractor evaluate)
The pump basket is damaged / missing
The pump cavitates (*DIY TIP: Have contractor evaluate)
The pump is leaking at the pipe connection in / out (*DIY TIP: Have contractor evaluate)
The pump wiring is loose / detached (*DIY TIP: This is a hazard)
The pump does not possess a shutoff switch at the equipment (*DIY TIP: Have contractor evaluate)
Air BlowerThe air blower is functional
The air blower is non operational
The air blower is loose at the post connection
The air blower possess loose / exposed wiring (*DIY TIP: This is a hazard)
The air blower is not bonded (*DIY TIP: This is a hazard)
The air blower does not possess a back-flow valve
PipingThe pool piping is functional
The pool piping needs support
The pool piping is leaking suction line / return line (*DIY TIP: Have contractor evaluate)
The pool piping needs to be painted
The pool piping is cracked (*DIY TIP: Have contractor evaluate)
The pool piping is too small (*DIY TIP: Have contractor evaluate)
The pool piping possess too many 90’s (*DIY TIP: Have contractor evaluate)
ValvesThe valves are functional
The valves leak suction / return lines (*DIY TIP: Have contractor evaluate)
copyright diyinspectionchecklist.com 2018 �78
NOTESThe valves have missing handles
The valves are automatic and non functional (*DIY TIP: Have contractor evaluate)
The automatic valves do not operate with remotes (*DIY TIP: Have contractor evaluate)
FiltrationThe filter is functional
The filter leaks band gasket / pressure gauge / backwash (*DIY TIP: Have contractor evaluate)
The filter has high pressure (*DIY TIP: Have contractor evaluate)
The filter is too small (*DIY TIP: Have contractor evaluate)
The filter allows debris back into the pool (*DIY TIP: Have contractor evaluate)
The filter pressure gauge is damaged
The filter backwash housing is missing (*DIY TIP: Have contractor evaluate)
Heating SystemThe heating system was functional AND bonded
The heating system short cycles
The heating system was not functional
The heating system is too close to the property line
The heating system vent is too close to a window / combustible material / wall
The heating system is not bonded (*DIY TIP: This is a hazard)
Gas PipingThe gas pipe appears function (always pressure test the gas line prior to purchase)
The gas pipe is laying on grade (*DIY TIP: Have contractor evaluate)
Gas leak noted (*DIY TIP: This is a hazard)
The gas pipe is missing a shutoff valve (*DIY TIP: Have contractor evaluate)
The gas pipe is not sleeved through the slab
The gas pipe is rusted and deteriorated (*DIY TIP: Have contractor evaluate)
The gas pipe was added without a permit (*DIY TIP: Have contractor evaluate)
The gas pipe is not secured
The gas pipe is too small
copyright diyinspectionchecklist.com 2018 �79
NOTES
ElectricalEQUIPOTENTIAL BONDING TO GRID
The bond wire is visible and assumed to be tied into the pool body, decking etc…
There is no visible bonding wire (*DIY TIP: This is a hazard)
The bond wire is too small (*DIY TIP: This is a hazard)
The bond wire is not connected to :_____________________________ (*DIY TIP: This is a hazard)
RECEPTACLES
The receptacles are functional
The GROUND FAULT receptacles are functional
There are receptacles which were non operational (*DIY TIP: Have contractor evaluate)
There were receptacles with missing / damaged cover plates (*DIY TIP: This is a hazard)
There wasn’t at least one receptacle not less than 6’ and not more than 20’ from the inside pool wall (*DIY TIP: This is a hazard)
The receptacles located between 6-20’ were not GROUND FAULT protected (*DIY TIP: This is a hazard)
There were receptacles located less than 6’ from the pools edge (*DIY TIP: This is a hazard)
ELECTRIC PANEL
Sub Panel Service Panel CoverSPC is Okay
SPC is damaged (*DIY TIP: This is a hazard)
SPC is loose (*DIY TIP: Have contractor evaluate)
SPC hinges missing / damaged / loose (*DIY TIP: This is a hazard)
SPC missing (*DIY TIP: This is a hazard)
Sub Panel Dead Front CoverDFC is okay
DFC is missing (*DIY TIP: This is a hazard)
DFC is damaged (*DIY TIP: This is a hazard)
DFC is missing screws
DFC is screws are pointed and not blunt (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �80
NOTESDFC is missing breaker labels (*DIY TIP: Have contractor evaluate)
DFC breaker labels are worn
DFC is missing knockouts (*DIY TIP: This is a hazard)
DFC is not tight to breakers leaving a gap (*DIY TIP: This is a hazard)
DFC is not original to panel replaced / modified (*DIY TIP: Have contractor evaluate)
DFC is rusted / deteriorated
Sub Panel Service SizeThe service size is _________ amps
The panels rating is __________ amps
Sub Panel Wiring MethodsThe wiring appears to be Non Metallic cable (Romex)
The wiring is drawn through conduit
Sub Panel Bus BarThe bus bar looks okay
The bus bar is scorched / damaged (*DIY TIP: This is a hazard)
The bus bar appears to have been replaced (*DIY TIP: Have contractor evaluate)
Sub Panel Infrared ObservationsNo visible issues
Heat in excess observed at one or more connections / breakers / wires (*DIY TIP: Have contractor evaluate)
Sub Panel Circuit BreakersCircuit breakers okay
Damaged Circuit breakers (*DIY TIP: This is a hazard)
Circuit breakers not approved for this panel board (*DIY TIP: This is a hazard)
Circuit breakers scorched (*DIY TIP: This is a hazard)
Circuit breakers loose (*DIY TIP: This is a hazard)
Circuit breaker is tripped for unknown reasons (*DIY TIP: This is a hazard)
AFCI (blue button) recalled (*DIY TIP: This is a hazard)
GFCI breaker defective (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �81
NOTESCircuit breakers amps too large for appliance / circuit / wire (*DIY TIP: This is a hazard)
Sub Panel WiringWiring looks okay
Wires scorched (*DIY TIP: This is a hazard)
Wires are corroded or deteriorated (*DIY TIP: This is a hazard)
Wires loose in panel not terminated (*DIY TIP: This is a hazard)
Two or more wires into one breaker (*DIY TIP: This is a hazard)
Wire is too small for breaker size (*DIY TIP: This is a hazard)
Wire / circuit is not protected by breaker / fuse (direct tap) (*DIY TIP: This is a hazard)
Sub Panel Neutral / Grounding BusThe neutral and grounding bus are separate
The sub panel appears to be incorrectly bonded to the equipment panel board (*DIY TIP: This is a hazard)
Neutral and grounding conductors are intermixed (*DIY TIP: This is a hazard)
Sub Panel Wiring TypeThe wire type is non metallic ( Romex)
The wire type is stranded wire pulled through conduit
The wire type is old Aluminum
The wire type is pre-1984 Non metallic ( Romex)
Sub Panel Grounding SystemThe GROUNDING ELECTRODE CONDUCTOR is present
There is no GROUNDING ELECTRODE CONDUCTOR (*DIY TIP: This is a hazard)
The GEC is disconnected (*DIY TIP: This is a hazard)
TIMER BOX
The timer box was functional and safe
The cover protecting the electrical connections is missing (*DIY TIP: This is a hazard)
The timer box is loose (*DIY TIP: Have contractor evaluate)
The timer box is damaged (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �82
NOTESConduit is loose / disconnected from the timer box (*DIY TIP: This is a hazard)
REMOTE CONTROLS
The remote control was functional within the home / spa
The remote control was non functional where tested (*DIY TIP: Have contractor evaluate)
OTHER ELECTRICAL
There were loose / exposed wiring within the pool equipment area
There is metal conduit that is deteriorated / damaged (*DIY TIP: This is a hazard)
Switches which cannot be determined (function) (*DIY TIP: Have contractor evaluate)
Other receptacles which were not operational (*DIY TIP: Have contractor evaluate)
Lights which were added around the pool which are too close (*DIY TIP: This is a hazard)
Loose wiring not terminated properly (*DIY TIP: This is a hazard)
Open junction boxes (*DIY TIP: This is a hazard)
copyright diyinspectionchecklist.com 2018 �83