Date post: | 28-Mar-2018 |
Category: |
Documents |
Upload: | duongkhuong |
View: | 221 times |
Download: | 0 times |
Home About Me Links
Post By: Admin On: Aug 18/12 With 20 Comments
DIY Resistor Substitution Decade Box
Here’s a handy guild on how to build your own DIY Resistor Substitution Decade Box.
I had seen several people online building their own, but instructions weren’t very clear. Hopefully these 50 or sopictures will help.
First step – hop onto ebay, and pick up some switches. You can find them by searching for “decimal thumbwheelswitch” – I think I only paid $5 for 10 of them including shipping (from china). Order up some extras – they can beused for all sorts of things – and a fun part to keep around.
News Blog
Here’s what they look like.
They “stack” and kinda snap together. Very Nice.
The back of them have some soldering points.
You’ll need 9 resistors for each “decade” – So 9 of each: 1Ω, 10Ω, 100Ω, 1kΩ, 10kΩ, 100kΩ, 1MΩ, 10MΩ, 100MΩ. You can choose how high you want to go. You can even exclude lower values if you wish. I choose to use 5%resistors cause that’s what I had on had. You can get a bit more accuracy with 1%. But I find that it doesn’t reallymatter that much, most likely you’ll be picking a resistor that has a standard value anyways. Such as 470Ω.
So pick 9 resistors – all the same value for that decade. In other words – each switch will be using all the samevalue of resistors.
The spacing on the switches is a bit less than what a 1/4 watt resistor will fit. You might be able to fit a 1/8 wattresistor in there, but in this case – you’re better off with 1/4 watt. Remember – there nothing keeping you frompassing too much current through a resistor. Bend 8 of them into this shape. The 9th one, keep it straight.
Now lets start – here the pattern for the first set of 8 resistors
Insert
Keep going…
Solder them up.
And trim the leads.
The 9th resistor needs to span from “pin” 5 to 4.
There’s room for it to ride on top.
We’ll need a “jumper” from 9 to C – note that this how it looks from the bottom.
I know the solder joints look a little mess – but there’s no solder mask on the PCB – so solder likes to flow. It’skinda a tightly packed board.
Mark the board with it’s resistor values.
Lather, rinse, repeat….
Now – stack the boards in the order as shown. Lowest value resistors are on the right.
Stack ‘em up!
Next we need to wire each board to the next. Grab some of the resistors leads you cut. There will be two remainingholes in the board. Wire from one to another like so:
I had this case laying around from Radio Shack. I think it’s a standard hammond case. http://www.radioshack.com/product/index.jsp?productId=2062280
Radio shack part number 270-1802
I measured the thickness of the switches – then use the other side of the calipers to scribe a line onto the case. I setthe case down (open side down) on a smooth table edge, and use the sharp points of the calipers to scribe a line.
It just fits!
Follow the like with a razor to make a line that you’ll cut up to.
I removed most of the material with a dremel – then used wood files to get right up to the lines I made.
There is one stand up in the way – it needs to be removed.
The lip of the lid also needs to be trimmed.
Almost there – keep trimming until it fits nicely.
I also had some radio shack banana jacks laying around (I really never buy parts from RS – but I happen to havethem on hand)
Remove the metal tab and give it a bend to fit the case.
Solder some wires.
And solder the wires to the top and bottom of the stack. there will only be two “holes” left to solder to.
Scred the lid on – and – your done. You can see the top unit I didn’t include a 1 ohm resistor in the chain. So Iremoved the buttons from one, and set the dial to “0″ to make it easy to read!
Share this: TweetTweet 4 Email Facebook Reddit StumbleUpon Print
mianchen
As seen on Adafruit.com show and tell! (Starts at 4:45)
(Visited 5,147 times, 66 visits today)
20 Responses to “DIY Resistor Substitution Decade Box”
August 19, 2012 at 2:07 am
Very good tutorial to follow. Unfortunately I’ve bought the wrong type of switches – BCD instead ofdecade ones…Have to wait for new ones to arrive. I suppose I can use them for a capacitance box.
Kaz
REPLY
Doug G
Terry
admin
Ricardo
Rodrigo Reis
REPLY
REPLY
REPLY
David Galloway
REPLY
REPLY
REPLY
August 22, 2012 at 5:05 am
Actually, BCD switches just mean fewer resistors are needed… as I understand it, you’d justneed a 1, 2, 4 and 8 to get all of the values (and the switch will combine them as appropriate).
August 19, 2012 at 3:35 pm
Very cool project idea. I just bought the switches, binding posts and resistors on ebay (still need tobuy the enclosure). I figure the total cost should be around $20.
I bought the resistors in packs of 50 or 100 so I should be able to hand pick the best ones in and putthem in order (most accurate to least).
I can’t see ever going up to 99,999,999 M ohms, but if I did need to…
Now what to do with the other two switches???
August 19, 2012 at 10:24 pm
Why do you need the jumper from ‘p’(Did you mean 9?) to ‘C’?
If your external contact points are ‘C’ and ’0′ I’d have thought ’9′ would be un-terminated.
August 20, 2012 at 4:37 pm
Yes Terry – that was a typo. It’s form 9 to C as shown in the picture.
August 21, 2012 at 2:24 pm
Why do you need the 9 to C jumper at all?I’ve done one box without it and it works perfectly fine.The only difference is that when the contact is moving from on position to another, youget an open circuit and not a 9
August 22, 2012 at 4:37 am
I think, without the jumper, you could use the decade like a potentiometer,using the 9 as +, C as SENSE and 0 as -.
I Live this thing
August 19, 2012 at 11:03 pm
Hey, saw your project on adafruit show and tell.Very cool. I think it’s interesting to see the relationship between this and a ladder style digital toanalog converter where instead of the switches being set by hand they are set quickly by amicrocontroller to generate a waveform.
Building a resistor substitution decade box - Hack a Day
Belgaum news | About Belgaum | Belgaum information | Belgaum district | Belgaum city | Belgaum Hotels |Belgaum People | Belgaum tourism | Belgaum entertainment | Belgaum students | Inside facebook | Hack | makeuse of | technical news | | Building a resi
Building a resistor substitution decade box
Ziga
Building a resistor substitution decade box « My Horizon Wireless
Wehrdo
Mihail
dfhfdsghsfdg
Todd Harrison
admin
REPLY
REPLY
REPLY
REPLY
REPLY
REPLY
REPLY
REPLY
REPLY
REPLY
August 21, 2012 at 11:31 am
[...] built an incredibly tidy resistor substitution decade box. These devices feature a pair ofconnections and a way to select the resistance between the two of [...]
August 21, 2012 at 11:45 am
[...] built an incredibly tidy resistor substitution decade box. These devices feature a pair ofconnections and a way to select the resistance between the two of [...]
August 21, 2012 at 2:18 pm
[...] built an incredibly tidy resistor substitution decade box. These devices feature a pair ofconnections and a way to select the resistance between the two of [...]
August 21, 2012 at 2:56 pm
Cool project, (Hackaday referenced). Definitely doing this! You should add a comma for kilo and mega.
August 21, 2012 at 7:41 pm
[...] built an incredibly tidy resistor substitution decade box. These devices feature a pair ofconnections and a way to select the resistance between the two of [...]
August 21, 2012 at 8:16 pm
That is slick! If I did more electronics work, I would definitely make this. Very easy to follow, too.
August 22, 2012 at 6:16 am
Shut up and take my money
August 22, 2012 at 8:51 am
It would be nice if you explained why you made the specific resistor connection you did and showedthe math.
Nice build otherwise, though.
August 29, 2012 at 10:05 am
In your notes you say “Lowest value resistors are on the left” but it looks like the lowest value are onthe right.
e5frog
jondaddio
REPLY
REPLY
Match the sliders on the left to each color band onthe resistor.
Click Here for a new resistor image.
If you'd like to learn more, read about resistor colorcodes here.
REPLY
0123456789
0123456789
0123456789
5
10
20
0Ω+/- 5%
September 5, 2012 at 5:54 pm
Whoops – that was a error – it’s now fixed – thanks!
January 6, 2013 at 9:51 am
Very nice build, I’d like to make one of them right now!
January 7, 2013 at 9:59 am
The price on eBay has doubled on the pushwheel switches. The specific eBay picture above was theprice shown yesterday (6 Jan) at $16.93, but today (7 Jan) the price for the same KSA-2 item (samepicture ad and label) is $33.86.
They noticed the articles and interest in the switches and jacked up the price.
Leave a Reply
Name (required)
Mail (will not be published) (required)
Website
Prove you are human by reading this resistor:
Submit Comment
Copyright © 2012 digitalunderpants.com
0 0 0 5