Date post: | 07-Apr-2018 |
Category: |
Documents |
Upload: | john-lever |
View: | 245 times |
Download: | 0 times |
of 54
8/6/2019 DJI Manual
1/54
1
DJI XP3.1 Standard Manual
V 1.10
DJI Innovation TechnologyAddress: Room 1205, Business ParkShenzhen University-town, Lishan Rd,
Nanshan District, Shenzhen, Guangdong,
P.R.ChinaP.C:518000Tel: 0755-83067827Fax: 0755-83067370URL: http://www.dji-innovations.com/Email:[email protected]
8/6/2019 DJI Manual
2/54
2
ContentsACKNOWLEDGEMENT .................................................................................................................. 4PREFACE ........................................................................................................................................ 51 INTRODUCTION ........................................................................................................................... 5
1.1FUNCTION INTRODUCTION ...................................................................................................... 51.1.1System Features ..................................................................................................... 51.1.2 Hardware System ................................................................................................. 61.1.3 Control Mode ........................................................................................................ 6
1.2SYSTEM REQUIREMENT ............................................................................................................ 82 SYSTEM ....................................................................................................................................... 10
2.1SYSTEM FRAMEWORK ........................................................................................................... 102.2MODULE INTRODUCTION ...................................................................................................... 11
2.2.1Main Controller .................................................................................................... 112.2.2 Adapter ............................................................................................................... 112.2.3 GPS & Compass .................................................................................................. 122.2.4 LED Status Indicator ............................................................................................ 122.2.5 Software .............................................................................................................. 12
3 SYSTEM INSTALLATION AND ADJUSTMENT ........................................................................... 133.1HARDWARE INSTALLATION .................................................................................................... 13
3.1.1 Main Controller Installation ................................................................................ 133.1.2 Adapter Installation ............................................................................................ 16
3.2SYSTEM PARAMETERS TUNING AND SETTING ............................................................................. 223.2.1 Tuning Preparation ............................................................................................. 223.2.2 The Primary Setting of Remote Control ............................................................ 233.2.3 Completion of the First Test Flight Adjustment by Software Wizard .............. 23
4 OUTDOORS FLYING ADJUSTMENT ........................................................................................... 354.1HELICOPTER FLYING ADJUSTMENT AND TEST UNDER MANUAL MODE .......................................... 354.2CENTER SETTING .................................................................................................................. 364.3COMPASS CALIBRATION ...................................................................................................... 384.4FLIGHT TEST UNDER AUTOPILOT MODE .................................................................................... 39
4.4.1 Setting Meanings and Related Regulation Methods of Parameters ............ 404.4.2 Flying Test ............................................................................................................. 434.4.3 Flight Success: ..................................................................................................... 43
4.5POINTS FOR ATTENTION IN FLYING .......................................................................................... 434.5.1Preflight Examination Process ........................................................................... 434.5.2 Flying Attention Points ........................................................................................ 454.5.3Landing Explanation .......................................................................................... 46
3 APPENDIX .................................................................................................................................. 48APPENDIX A:LED STATUS INDICATOR .......................................................................................... 48APPENDIX B:ELECTRICAL CHARACTERISTICS ................................................................................ 49
8/6/2019 DJI Manual
3/54
3
APPENDIX C:MECHANICAL PROPERTIES ...................................................................................... 49APPENDIX D:MECHANICAL DRAWING ........................................................................................ 50APPENDIX E:PACKAGING LIST .................................................................................................... 53APPENDIX F:SAFETY CHECK LIST ................................................................................................. 53APPENDIX G:FREQUENTLY ASKED QUESTIONS .............................................................................. 54
8/6/2019 DJI Manual
4/54
4
AcknowledgementI hereby would like to acknowledge the support, hard working and
modification of our manual. My sincere gratefulness goes to our distributor,
Mr Kimberly Attwell
, whose guidanceexpertise and effort provide an
important support throughout the work of our manual.
DJI Innovation Technology
Note:Authorized area: New Zealand & Australia
: Here is some general information about Mr Kimberly Attwell:Company: PHOTE HIGHER
Phone Number: 006449735744
http://www.photohigher.co.nz
http://www.photohigher.co.nz/http://www.photohigher.co.nz/8/6/2019 DJI Manual
5/54
5
PrefacePlease read this manual carefully before using DJI XP 3.1. If you have any
questions, please contact us. We will give you satisfying answers as quickly as
possible. Our company undertakes no risk and obligation for the product's flight tests
and utilization of our end-users, such as aircraft crashing, direct and indirect loss of
the third-party caused by aircraft crashing.
Our company reserves the right to revise any part of this manual without
informing users beforehand.
1 Introduction1.1 Function Introduction
DJI XP3.1 is a controlling system for unmanned system, integrated with GPS,
6-DOF inertial measuring unit, Magnetic-field meter and barometer. The system can
control the helicopter precisely and reliably at any flight altitude, in most weatherconditions, and even under the short-interruption of GPS signal.
1.1.1System Features
Helicopter, a non-stable platform itself, needs continuous observation and
controlling to maintain a steady flight. DJI XP3.1 provides excellent auto hovering
and flight performance by using GPS/INS inertial navigation technology, which is
widely used on cruise missile, and advanced controlling algorithms.
Main Characteristics of DJI XP3.11. Autonomously hovering with high precision.2. When autonomously hovering, the helicopter altitude and position can be
locked. Flight velocity in one direction corresponds a given RC stick volume,
so users can control a fool-style flight( can only control one channel at one
time)
3. Under the locked altitude, with the help of XP 3.1, operators can easilycontrol the helicopter to do the turn-coordination.
4. Amend errors raised between hovering and flying automatically.5. The main differences between DJI XP3.1 and the stability augmentations
8/6/2019 DJI Manual
6/54
6
based on CCD sensor: DJI XP3.1 can fly at any altitude within the remote
control smoothly, without height and surface texture restraints. No frequent
switching between various modes, the speed can be accreted to 0.1m/s orless.
6. Automatically turn into hovering state when receiver signal is lost (enter theFail Safe mode).
1.1.2 Hardware System
1. Improve the accuracy and real-time performance of the controller by using2 separate DSPs (digital signal processor) to calculate altitude and control
algorithm.2. Provide superior position accuracy by using a high performance 16-channelGPS receiver.
3. Enclose high-reliability tri-axial gyroscopes and accelerometers of MEMS.4. Building algorithm can facilitate users to do the hard and soft iron magnetic
field compensation for eliminate the magnetic interference.
5. The system dedicates CPLD to decode and encode servo signal for higherreliability and compatibility for most RC receivers.
The Basic Performance ParametersHover positioning accuracy Maximum wind
resistance
Vertical 1m5.5~7.9m/s
Horizontal 2m
Note:
1.1.3 Control Mode
These parameters are measured in the condition of breeze (wind speed less than 3.3m/s). If in heavier
wind, the accuracy will be little lower.
Autopilot ModeIn this mode, the altitude can be locked; the nose direction and the
helicopters velocity command, back and forth, left and right, up and down, can
be issued by RC transmitter (Tx) separately and accurate feedback control through
on-board automatic control algorithm. Even people, who are flying the RC
helicopter for their first time, can learn to control the helicopter in few minutes.
There is a hovering zone
when Tx sticks are centered. When the sticks go back
8/6/2019 DJI Manual
7/54
7
to the middle (centre position) and enter the hovering zone, the system will enter
auto-hovering in a short time.
After entering autopilot mode, flight speed is in proportion to the volume of Txstick
When the Tx stick is pushed to the limit, the corresponding maximum flight
speeds are as followings:
.
Forward-Backward Left-Right Up-Down
56km/h 54km/h 7.2km/hNote:The small section of the hovering zone on the Tx is determined by the controller system.The ROTOR EPM is locked by GV1 or ESC.
Attitude Control Mode:In order to keep helicopter in safe range, system velocity is intentionally limited within 15m/s.
System also has the attitude stable mode. It can work even without GPS signal in
this mode. When user switches into this mode, helicopter will hold stable attitude and
altitude but without position and velocity locking. The helicopter can be easily
controlled in a no GPS condition.Pure Manual Mode
The system remains in traditional manual mode. Under this mode, operator can
control the helicopter as an ordinary RC helicopter.
8/6/2019 DJI Manual
8/54
8
1.2System RequirementHelicopter Types Applicable to electrical and gas/fuel powered
helicopters
Swash Types
Ordinary modeCCPM 1_Servo_Norm
CCPM mode1. 3_Servo_120
2. 3_Servo_140
3. 3_Servo_90
4. 4_Servo_90
Remote Controller 1. 7 channels or more2. All channels have the Fail Safe function
System OperatingTemperature -10 ~ +70
System OperatingVoltage 7.4~12V(DC)
RecommendedSystem Power
Supply
The specifications of lithium battery as followings
Voltage: 7.4V Battery capacity: More than 2000mAH
Discharging current: Larger than 5C
RecommendedAccessories
1. GyroscopeGY401
2. Speed controller: ESC (electromotion), GV1
(kerosene-powered) practicably locking the
revolving speed
3. Receiver(PCM)
or 2.4GNote: Some of the RC systems (like some kinds of Spektrum RC), only the throttle (the first channel) has the
function of Fail Safe, none of the other channels have Fail Safe function. As a result, it is not
guaranteed that the helicopter can enter the auto-hovering state when the RC is in out of range.
For the lithium battery of these specifications, the voltage can reach more than 8V when it is at full power state (there are two 3.7V batteries connected in series inside. If there are three 3.7v batteries
connected in series, it may exceed the system operating voltage, so it is not recommended). If the
measured voltage is 7.4v, the battery is at the edge of being empty. As a result of using powerful
DSP+ARM to process efficient attitude control algorithms, the system working current may approach
8/6/2019 DJI Manual
9/54
9
more than 1A. By using the lithium battery with capacity is over 2000mAH, the system can work for
around 2hours
: System alarming voltage is 7.4v (under this condition the red LED status indicator will always on): The gyroscopes will induce this change (and confirm it is not artificial operation), and emend this impact.
After testing, the compatibility between GY401 and XP3.1 is higher than that between GY601 and
XP3.1, so GY 401 is recommended.
Engine governor such as GV-1 or RPM lock-able motor drivers are required to maintain a constant rotorRPM and XP3.1 will leave the Thro channel in the original position in the autonomous mode.
PCM or 2.4 G receivers have Fail Safe function, but PPM do not.
8/6/2019 DJI Manual
10/54
10
2 System2.1System Framework
NoteBlack: Normal configured mode
Blue: Optimal configured mode
Brown: User-configured mode
Receiver
Tx
Servo
Ext. portsED
GV1/ESC.Power
Gyroscope
Compass&GPS
Adapter
Gyro Stable P&T
SD CardWireless
Main Controller
8/6/2019 DJI Manual
11/54
11
2.2Module Introduction2.2.1Main Controller
The Main Controller, which calculates the flight attitude and controls of the
helicopters flight by sending orders to Adapter under autopilot mode, is the heart
of the control system.
Figure 2. 1 Main Controller
2.2.2 Adapter
The Adapter acknowledges signals from RC receiver (Rx), as well as processing
controlling signal and controls the servo operation with cooperation of Main
Controller.
Figure 2. 2 Adapter
8/6/2019 DJI Manual
12/54
12
2.2.3 GPS & Compass
External GPS and compass are integrated in one unit. Both of them must be
placed far away from interference. It is used to receive GPS signals and direction
signals, and send them to the Main Controller.
Figure 2. 3 GPS&Compass Figure 2. 4 LED Status Indicator
2.2.4 LED Status Indicator
The LED status indicator has three LEDs which are red, white and green. They
have a number of different states constantly on, sparkling, flashing and constantly
off. Each state represents different control status respectively(Refer Appendix A for
details).
2.2.5 Software
PC software called XP configure is used to program and make system
adjustments. Users need to set different parameters for each helicopter to make sure
the system operate normally.
8/6/2019 DJI Manual
13/54
13
3 System Installation and Adjustment Users should dedicate special circumspection and patience to the
installation, adjusting, flying and maintenance of the system. Any improperoperation may lead losses of helicopter, property and even life. Please pay specialattention to the following steps and introductions of installation and adjustment. Donot try to skip any step.
This sign stands for Fatal Danger.Users should pay special attention to itand handle with care.
3.1 Hardware InstallationBefore you install XP 3.1, please make sure the mechanical structure of the
helicopter has been adjusted correctly
Note
and the helicopter can process normal
manual flight in the absence of this system.
3.1.1 Main Controller Installation
Try to eliminate all kinds of vibrations by adjusting mechanical structure and motor system, since the
oversize vibration will influence the normal operation seriously.
1. Please assemble the anti-vibration frame of the main box first. The MainController is fixed to the anti-vibration frame of main box by 4 neoprene
isolators, as shown in Figure 3.1.
Figure 3. 1
2. Main Controller installation can be installed in two ways, with reference of thecoordinates of Main Controller (Figure 3. 2) and helicopter (Figure 3. 3). NoOther Installation Is Allowed.
8/6/2019 DJI Manual
14/54
14
Figure 3. 2
Figure 3. 3
a) (Figure 3.4)Make Main Controller box frame the same direction as thehelicopter frame, which means the side with two DB ports faces the
head of the helicopter, This corresponds to the Forward set in the
[Install Parameters] in XP configure(programming software).
b) (Figure 3.5) Make X Axis of Main Controller in the line of Y axis ofhelicopter, which means the side with two DB ports faces the right hand
of the helicopter, corresponding to the Right set by the [Install
Param] in XP configure.
Figure3. 4 Figure3. 5
Forward Position Right Position
8/6/2019 DJI Manual
15/54
15
Attention1) For the helicopter with gasoline engine and electric motor, the
minimum distance between the Main Controller and the engine/motoris 10cm. For the helicopter with methanol machine, one does not needto consider the distance between them.
2) The distance between the Main Controller and the center of gravityshould be as close as possible, the shorter the better. Its also to keepthe main controller out of direct contact with the airflow from the mainrotors.
3) The installation direction should as straight as possible, or it will decreasethe control accuracy.
4) The Main Controller must not be too close to any heat sources orelectromagnetic interference or servos.
5) Users should reserve enough space for the connecting cable betweenMain Controller and Adapter as well as computer in front side of theMain Controller (the side with two DB ports).
3. Users can find a suitable position
for the Main Controller according to the
above requests and helicopters structure. Followings are two installation
examples (Figure3. 6 and Figure 3. 7).
Figure3. 6
8/6/2019 DJI Manual
16/54
16
Pay attention toprotect DB15 cable andavoid long-time friction,
which may leadsshort-circuit or open-
circuit!
Figure 3. 7
Note
Attention
Drill the correct size holes in the anti-vibration frame and helicopter to fix the Main Controller
to the helicopter. You may need to customize your own brackets depending where you can fit
the anti-vibration frame. It is important that the Main Controller is well supported and fixed
rigidly to the frame of the helicopter.
Check the bearing capacity of neoprene isolator on a regularly basis, andcheck that there are no signs of weakness or aging. If any of the isolators are wornor cracked you need to replace them straight away!
3.1.2 Adapter Installation
1. Position Choice of Adapter1) The minimum distance between the Adapter and the engine (gasoline
engine or electric motor) must be 10cm at least, or interference can affect
the operation of the system.
2) There are many links between Adapter and RC receiver and servos
respectively. Arrange a proper position for
Adapter installation to reduce the use of the
extension cables.
3) Do not fix the Adapter to the helicopter after
choosing a proper position. Fix it after all the
adjustment has been made.
8/6/2019 DJI Manual
17/54
17
2. Connection between Main Controller and AdapterConnect them with DB 15cable (Figure 3. 8), which matches DJI XP3.1. The clasp of DB 15 cable must be
locked (Figure3. 9 DB15 open status) (Figure3. 10 DB15 closed status). Thelooseness of DB15s clasp must be avoided. The routing should not be pulled
to tightly (Figure 3. 11). A longer cable can be supplied if required. Do not
constrain the DB15, which links to the port of the Main Controller. Keep it
flexible to avoid affecting the attitude of the Main Controller and/or reducing
the efficiency of isolators. The recommended way is shown in Figure 3. 12
Figure 3. 8DB15 Cable Figure3. 9 Unlock Status Figure3. 10 Locked Status
Figure 3. 11 Figure 3. 12
3. Connection between RC Receiver and AdapterFix the Rx first. And thenconnect Adapters input wires to the Rx according to the label on them
(Figure 3. 13) and check the power polarity when plugging them in. No
external power supply is needed for Rx, because its power is supplied directly
from the Adapter (Figure 3. 14).
Figure 3. 13 Figure 3. 14
8/6/2019 DJI Manual
18/54
18
No other linksexcept input wires of
Adapter are allowed toconnect to the RCreceiver, for example:Any servo or electronic
shutters.
Definitions of the Rx input wires are shown as follow:Label T A E R U P G X
Definition THRO AILE ELEV RUDD AUTO PITCH GYRO AUX
Note:: Autopilot/ manual channel: Gyro sensitivity channel
Connection: For 4-servo swash
schematic diagrams
Figure 3. 15
Figure 3. 16
AttentionJR and Futaba RC receivers are promoted,
because in this manual we set them asexamples. By using them users can makeconnection according to the above two charts.Please check if the channel definition of the Rxcorresponds to that of the above charts. If not,just make sure that the match up.If other Rxsare used, users should connect them as per thedefinitions of wires.
4. Connection between Servo and AdapterAs in Figure 3.17, the 8 marked portsare output channels to the Servos (Figure 3.17). Servo power supply (4.8v-6v) is
connected to the BATT channel of Adapter. The connections are the same as
http://showjdsw%28%27jd_t%27%2C%27j_%27%29/http://showjdsw%28%27jd_t%27%2C%27j_%27%29/http://showjdsw%28%27jd_t%27%2C%27j_%27%29/8/6/2019 DJI Manual
19/54
19
that of connecting between Rx and Servos. The followings diagrams show the
schematic of swash plates of various configurations with three servos
(including normal mode, 90CCPM120CCPM140CCPM and fourservos (90CCPM). Please follow the following connection shown in Figure3.
18 and Figure 3. 19.
Figure 3. 17
Figure3. 18 3-servo Swash
Figure 3. 19 4-servo Swash
8/6/2019 DJI Manual
20/54
20
AttentionPower supply for the Servos and the control system are two mutually
independent and different supplies. The Servos are supplied with power source of4.8v-6v battery and must be plugged into the BATT port on Adapter. Please install aswitch between the servos battery and the port. The controller system ispowered directly with a 7.4v battery. The switch on Adapter is the power switch ofcontrol system. Be sure two batteries ground links are not connected together.
5. Connection between LED Status Indicator and AdapterT the LED statusindicator (Figure 3.20) is connected or plugged into the corresponding port
labeled LED on the Adapter shown in Figure 3. 21. Please install the indicator
in the place where can be seen easily from different directions when
helicopter is flying. Users can refer to the following example (Figure 3. 22).
Figure3.20
Figure 3. 21 Figure 3. 22
6. Connection between the External GPS & Compass and AdapterThere arefour external ports on the Adapter to connect various relevant airborne
modules such as the external GPS &Compass, wireless video transmission
(matching), ground station radio (professional edition) and so on. No. 1 port isthe input port for GPS & Compass signal (Figure 3. 24). The upper surface (DJI
OutputChannelsforServos7
.4-12vBattery
20
00mAhplus
Batt. Port In
6-4.8v Battery
2000 mAh lus
H
eavyDutySwitch
Input Cables from Receiver
Servos Plug In
To GPS
DB15 Cable
Adapter
8/6/2019 DJI Manual
21/54
21
GPS & Compasscannot work correctly if
it is connected to theother port.
trademark surface) of GPS & Compass should
be facing upward. It should be laid flat and the
coordinates must be coincident with thecoordinates of the helicopter (output wire
points to the head of the helicopter). No magnetic objects are allowed close
to the GPS. It should be installed approximately half way along the tail boom,
and be far away from any servos.(Figure 3.25)
Figure 3. 23 Figure 3. 24
Recommended Installation:
Figure 3. 25
Attention1) The GPS reception will be affected if GPS is too close to the main rotor
or Servo; the accuracy of the GPS data may decrease when it is tooclose to the tail rotor
2) Distance between the external compass and servo should be morethan 20cm, and between compass and the engine should more than30cm.3) The tail boom must be carbon fiber or nonmagnetic material (thematerial must not be attracted to magnify fields). The screws near thecompass must be replaced with stainless steel. If you are not sure if thematerial near the compass is magnetic, you can use the magnet or theordinary compass to check.
4) If there are some ferromagnetic materials which have the maximumdimension x near the compass, the minimal distance betweenferromagnetic materials and the compass should be 2x
http://showjdsw%28%27jd_t%27%2C%27j_%27%29/http://showjdsw%28%27jd_t%27%2C%27j_%27%29/http://showjdsw%28%27jd_t%27%2C%27j_%27%29/http://showjdsw%28%27jd_t%27%2C%27j_%27%29/8/6/2019 DJI Manual
22/54
22
3.2 System Parameters Tuning and SettingIf users have followed the above installment introduction, then you should have
finished the connection of the hardware. Now we will start the parameter tuning
and the setting by software.
3.2.1 Tuning Preparation
1. Software InstallationPlease install the USB to Serial Port Cable driver. exe ofthe ancillary CD and XP Configure (system parameters tuning software) which
can be found on the CD supplied.2. Power and ConnectionConnect the Adapter to the 7.4v power. Connect theDB9 port on the Main Controllers front panel (Figure 3. 27) and the USB
connection of the computer with USB to Serial Port Cable (Figure 3. 26). Do not
turn on the power to the servo at this step.
Figure 3. 26 Figure 3. 27
3. System BootingTurn on the system power switch and pay attention to the LEDStatus Indicator. Refer to appendix A1 [normal booting mode] to see ifbooting is normal. If not, please refer to appendix A4 [error status], check if theinstallation is correct and reboot it. Refer to appendix A2 [normal operatingmode] to check the twinkle of the indicator after normal booting. If users aresetting up indoors, the red LED indicator will flash indicating no GPS signal
this is normal.
Attention:Every time when booting the system, please keep the helicopter flat, or thesystem will start failure.4. Software Connecting Open XP configure software, and then it will
automatically search for available COM port. If there are no problems, it will
connect to the Main Controller automatically. It shows the system has been
connected normally and smoothly when the connection indicator of the
software turns to green.
8/6/2019 DJI Manual
23/54
23
3.2.2 The Primary Setting of Remote Control
All the settings made through Tx by users have been reserved. Initially two
changes are required, first the swash plate type setting and autopilot switch setting.
1. Swash Type Setting
Note
Regardless of the brands of the remote controller, please
alter the swash type in remote controller to helicopter-Normal one. That
means each servo link to the swash plate independently.
2. Autopilot Switch SettingUsers need to set aFor JR RC Choose NORM in SWASH TYPE and for Futaba RC Choose HELICOPTER, H-1 in Swash
Plate.
three-position switch
Attention
on the Tx as
the autopilot switch this will enable you to switch among manual, attitude and
autopilot modes.
If users make connections according to the above explanation correctly, thechannel 5 of JR RC is the autopilot setting channel, while the channel 7of FUTABARC, but this will depend on the brand and type of receiver being used.
3.2.3 Completion of the First Test Flight Adjustment by Software Wizard
Once the above two changes have been made to the Tx users can now turn on
the control system (Adaptor) power (Dont turn on the servos power). Enter the
software after the normal starting of the system. When the indicator on the left of the
window turns to green from red, the software begins to work. And then, users can
enter adjusting wizard interface (Figure 3. 29) by clicking Wizard button n the top
left corner of the screen (Figure 3. 28).
Figure 3. 28 Figure 3. 29
8/6/2019 DJI Manual
24/54
8/6/2019 DJI Manual
25/54
25
Figure 3. 31
Users can measure the offset values according to the position of the Main
Controller and the helicopters c. g, and fill them in the proper position
on the programming software as shown.
Figure 3. 32
3 If GPS antenna is laid at Point B, then Bs coordinate value is the offset ofGPS to the helicopters C of G (Figure 3. 32).
As for the same reason, users can measure the GPS offset from the
position of GPS installation to the C of G of the helicopter. If users install it
at the point of 1/2 length of the tail pipe approximately, the offset values
of y and z are usually 0 (zero). You only need to find out the distance
between GPS and the c.g. of helicopter in x direction. Pay attention to
8/6/2019 DJI Manual
26/54
26
the positive and negative values of GPSs offset in the x direction, it
should be always negative.
Attention1. By default, users do not need to change the offset value of the GPS in y
and z directions in the software and can be left at 0. But if you do notinstall GPS at the recommended position, you can enter the values of yand z by clicking Advanced.
2. To set the expected parameters into the Main Controller to finish setting,do click write after filling the parameters in
3. Meter is the unit of all the offset parametersNote:
: One way to determine the c of g. of helicopter is to take down the main rotor, tie a long line with plumb to the tail pipe, raise the helicopters tail, and let the helicopter and the ling hang down
naturally this will give you the X coordinate. To find the Y coordinate you can find the balance
point of the helicopter when it is sitting on its skids. One way is to balance the helicopter on a
round bar. The intersection point of the plumb line and the horizontal balance point is the C of G of
the helicopter.
STEP2.Autopilot/Manual Mode Setting1 Click next button after finishing the operations above to enter
8/6/2019 DJI Manual
27/54
27
autopilot/attitude/manual mode setting. After turning on the Tx, users are
able to shift autopilot/attitude/manual switch. Then you will notice the
slide also shifts between the top side and bottom side, which means theautopilot/attitude/manual switch has been linked correctly. Users should
set the switch normal and reverse according to the slide direction
(upward position, slide is on upward side, and vice verse)
Please notice that after our updates, there are three modes possible.
Users should choose a 3-position switch as mentioned in 3.2.2.
2 Users must program every position of the 3-position switch by Tx in order toenter the corresponding mode. User could notice the slider moving when
programming very position of the switch. When slider reaches the orange,
green or blue area and there is a little trimming slider appearing on the
left, that means the adjustment in this mode is finished, as shown in Figure
3.34. Then shift the switch to the next position, program this position the
same way as above. So is the third position. After the setting
accomplished, you can shift the switch to make sure every position of the
switch corresponds the correct slider position.
3 Then you must set a fail safe position of this channel. Fail safe position ofthis channel can be set at any position except the set three modes
positions above, as shown in Figure 3.33. You may have to repeat the
settings for three positions after fail safe position settled.
Figure 3. 33
8/6/2019 DJI Manual
28/54
28
Figure 3. 34
4 When the switch is upside, the slide leveling with the orange line, the
8/6/2019 DJI Manual
29/54
29
green LED should vanish constantly, this is the manual mode. When switch
is centered, the slide leveling with the blue line, the green LED indicator
will start to sparkle, which means it enters attitude control mode. Whenswitch is downside, the slide leveling with the green line, the green LED
indicator will also sparkle, which means it enters auto mode. When turn off
the Tx the slider will be at the fail safe position you set. If you finished all
steps correctly, you have finished the adjustment. Please click next to
continue to the next step.
STEP3.Swash Type SettingUnder the manual mode, users can adjust the helicopter according to
the requirements for ordinary remote-controller helicopter.
1) Before this step, set the swash type as NORMAL mode in Tx first2) If your helicopter is NONE CCPM, set the Swash types as NORMAL in the
software (Figure 3. 35). click write and then next to enter the
interface of Feedback & Servo Calibration
Swash Type:Swash Type CCPM Parameter
Normal Type Normal CCPM Type
1. 3_Servo_120
2. 3_Servo_140
3. 3_Servo_904. 4_Servo_90
Swash Mix
NORM REVServo Rotation Direction
Figure 3. 35
8/6/2019 DJI Manual
30/54
30
Figure 3. 36
3) If CCPM mode is used (Figure 3. 36), parameters of swash mix and Servodirection should be set correctly.
a) First turn the TRAV ADJ (End Point) of every channel of control stickwhich controls PITCH, AILE, RUDD, ELEV to the Maximum.
b) Check that the swash type has been set to NORM mode in Tx.c) The moving direction of swash plate is decided by the rotation direction
of Servos and the sign (positive or negative) of swash mix, while its
motion amplitudetravelis decided by the values of corresponding
swash mix.
Push PITCH stick up and down and notice if all the Servos lead theswash plate moving horizontally, that means every servo lets the
swash plate up or down evenly. If not, click NORMREV
buttons to adjust the direction of Servo.
Push PITCH stick, the forward and backward movements shouldcorrespond to the changing of collective pitch of main rotor. If the
direction is opposite, change the sign of PITCH in swash mix. Push ELEV stick forward and backward should correspond to theforward and backward rotation of swash plate. The adjusting
methods are the same as above.
Push AIL stick right and left should correspond the right and leftrotation of swash plate. The adjusting methods are the same as
above.
4) It the swash slants slightly, users can correct this in the Tx by trim tuning. If theinclination is too big, please adjust the mechanical linkages of the swash
plate. Users can refer to the installation manual of the helicopter for details.
8/6/2019 DJI Manual
31/54
31
Figure 3. 37
5) Pay special attention to CCPM 4_Servo_90 Swash type (Figure 3. 37) First connect the pull rods of three servos only, for example, the left,
front and right Servos.
In the software interface of swash setup, configure the Swashtypes and the directions of the three Servos.
Connect the pull rod of the fourth Servo after complete adjustmentof the three servos. Adjust the direction of the fourth, to make sure
no locking braking
Note
between Servos and the correct motion of
swash plate.
6) Adjust the minimal collective pitch to -5 ,maximal one to 10-11
(guarantee the corresponding climbing speed more than 3m/s) and
median one 5 by the software and PITCH curve in Tx.
: No Kaka sound from Servo.
7) Click next after finishing the settings, to enter the interface ofFeedback & Servo Calibration.
STEP4. Feedback & Servo CalibrationThis step can allow the software to calibrate of stick volume and feedback
control. The main purpose is to get positive and negative directions and the
maximum minimum values of all channels.
8/6/2019 DJI Manual
32/54
32
Figure 3. 38
a) Enter the interface of [Feedback & Servo Calibration] (Figure 3. 38), andclick the Cal buttons of AILEELEVRUDDPITCH orderly.
AttentionThe Throttle and Pitch channels are mixed, so you will be adjusting
the throttle channel when you calibrate the pitch channel. If it is anelectronic helicopter, users need to set the last point of the throttle curveto the maximum when processing the calibration of the PITCH channel.Once you have calibrated the Pitch channel return the throttle end pointto its correct setting.
b) After entering calibration interface, push the stick to the center first;then click Ok (Figure 3. 39) and push stick according to the arrow
pointing direction shown from software (Figure 3. 40); Return the stick to
the center finally. Software will exit the calibration interface
automatically after the calibration of the corresponding channels.
Figure 3. 39
8/6/2019 DJI Manual
33/54
33
Figure 3. 40
AttentionMake sure to hold the stick at the endpoint for more than 2
seconds.c) Now check if the directions of stick travel are the same as shown in
software.(stick to left or upward corresponds to the slide shown in
software moving upward stick to right or downward corresponds to the
slide shown in the software moving downward). If calibrated correctly,
the top or the left end of the stick should correspond to the top position
of the slide. Meanwhile, the bottom or the right end of the stick should
correspond to the bottom of the slide. If the slide reaches the top or
bottom too early, or it cannot reach the top, re-calibration is needed.
d) Feedback Test. Switch the remote controller to Auto Mode or the prompt box will
appear (Figure 3.41).
Click Feedback Test button. Now, users need to check the swash plate. The swash plate will
move automatically. The directions as followings: collective pitch:updown; swash plate tilting: front- back-left-right; Rudder:left-right; throttle: up- down. If the directions are inconsistent, usersneed to re-calibration corresponding channels. Switch back to the manual mode and withdraw the test.
Figure 3.41
e) Switch the remote controller to auto mode(or the prompt box as above
8/6/2019 DJI Manual
34/54
34
The correctness ofFeedback testandController Orientation
Testwill affect thenormal operation of the
Main Controller.
will appear)
f) After clicking Controller Orientation Testbutton When helicopter inclines left, the
swash will tilt to the right.
When helicopter inclines right, theswash will tilt to the left.
When helicopter inclines front, theswash will tilt back.
When helicopter inclines back, the swash will tilt front Switch back to the manual mode and withdraw the test
Note: The Main Controller will keep swash plate as horizontal as possible. Tilting horizontal angel 10of helicopter will lead biggest moving amplitude of swash.
g) If the directions are not as the above, users should recheck theinstallation of the main box. Then re-click Feedback Test to check if
everything works normally. Or re-calibration the feedback direction.
Refer to [Swash setup] [Main Controller Installation] [Install Parameter].STEP5. Center Setting
This step is for user to set the way of center position recording in auto
mode. In the first flight which must be in manual mode, this will take no effect. So
please let it be the default setting which the Center record mode is chosen
on Tradition. You can finish this setting after successfully manual flight and
we will talk this later, in 4.2 Center Setting
Figure 3.42
STEP6. After the above tests complete, fix the Adapter on the helicopter toprepare for the outdoors flying test.
8/6/2019 DJI Manual
35/54
35
The main purpose isto get the optimumperformance undermanual mode in this
adjustment. Pleas Nevertry to shift to auto mode
when flying.
4 Outdoors Flying AdjustmentPlease read through this chapter before flying outdoors. Read 4.5 Points for
Attention in Flying before any flight. Please operate carefully to avoid anyaccident
4.1 Helicopter Flying Adjustment and Test under Manual Mode1) Test the RC antennas radio distance: take
down the main blades and turn on the
engine for the first test; then shorten the
antenna, do the test about 20m away from
the helicopter under manual mode. If the
green LED enters the auto mode, which will
start flashing, it indicates that RC is out of
range. Now, the user need to check if the
installation positions of Adapter and RC receiver are far away from
interference sources as engine, especially the gasoline engine.
2) After completing the installation and adjustment as an ordinaryremote-control helicopter, users can process the complete flying
adjustment under the manual mode and reach the stable flight
performance
3) Keep the helicopter stable temporarily even if the helicopter is not in controlling for seconds by tuning the trimming of RC. Now, users need to remember
the general position of PITCH stick
.
Note
Balance the main rotor to avoid twin screw phenomenon. Users need to adjust thehelicopter to a condition which it is almost impossible to notice the vibration by naked eyes.
: With the inertial measurement system (IMU) in the Main Controller, excessive vibration of thehelicopter will cause the Main Controller to be in an unstable state. So, to ensure the best performanceof the whole system, users need to minimize any vibrations as best as possible.
Adjust the pitch of the tail rotor so that in normal mode (not Heading Hold) there is noobvious rotation when hands off stick.
Push the rudder stick to the left/right endpoint and ensure the rotation speed of tail at 1circle per 2 seconds in left/right direction. After the adjustment, users can switch it to the
locking head mode
The reason for making the PITCH stick in the center when helicopter is hovering by adjusting
8/6/2019 DJI Manual
36/54
36
PITCH curve is to set them as the corresponding fail safe positions in the next step [Center Setting].
4.2 Center SettingClick the Center Position tab in the configuration software, there are
two ways to record the center position in auto mode.
1) Traditional ModeIn this mode, the auto hovering center would be the position of your stick
just when you switch into the auto mode, which will be different every time since
a user might have trimmed the helicopter during manual mode. The traditional
mode is often used during system configuration and adjustment.
If the fail-safe is set correctly under Auto/Attitude/Manual channel in your Tx,
the flying status of the helicopter in fail-safe would depend on whether the
fail-safe of other channels are properly set. If they are, helicopter would hover
stably in fail-safe state.
You will not be able to activate Go Home action in traditional mode.
2) Pre-set ModeIn this mode, the hovering center is pre-configured into the controller.
This mode is highly recommended when the helicopter is correctly
configured and adjusted, since it will provide a more stable performance and
safer flying. You only need to set fail-safe correctly in Auto/Attitude/Manual
channel in the Tx, without paying attention to the fail safe settings in other
8/6/2019 DJI Manual
37/54
37
channels, and you can choose Hovering or Go Home when the RC
signal is lost.
Choose Hovering:Follow the steps below to pre-set into Hovering option, and the
helicopter will hover when RC signal is lost.
Click Pre-set; Put all sticks at the hover position you recorded when flying under
manual mode (You will need to fly in manual mode first, and
remember the hover position of the sticks).
Click Read under the Center position from stick box, andthe software will read and show the exact values of the sticks
positions.
Choose Hovering in the Fail-safe action box, and click theWrite button under the Center position from stick box. Only
values from Aile, Elev, Rudd and Pitc channels are
useful, you will not need to pay attention to values of other
channels.
If you want to read and modify the settings in the Main Controller,click Read under the Edit center position box, and change
the values if needed. The Write button is for updating the value
settings and actions of the Hovering or Go Home from the
software to the Main Controller.
Choose Go Home:If Go Home option is chosen, helicopter will go back to the home
point
When the helicopter starts Go Home action, you cannot control it inauto mode even when signal is retrieved. To get back control of the helicopter,
you must switch to manual mode first, and then switch back to auto mode, and
the helicopter will be flying under the usual auto-mode.
automatically when RC signal is lost for more than10 seconds, and during
these 10 seconds the helicopter will be hovering.
The center setting would be the same for Go Home as above, except
that the user will need to choose Go Home instead of Hovering in the
Fail-safe action box.
3) Check Your SettingsTurn off your Tx, if the setting of fail-safe in Auto/Attitude/Manual channel is
8/6/2019 DJI Manual
38/54
38
correct, the Green LED installed on the helicopter will flash rapidly. Assuming
that you have chosen the Go Home option, the XP configure software will
print Tx signal lost..., and will print Start to go home!after 10 seconds.
AttentionEvery time users change the trim values, curves and end points of any of thefour channels mentioned above, recalibration and center positionre-adjustment will be needed for the particular modified channel(s).
DO NOT try Go Home function in a real flight, unless the helicopter canfly stably under auto mode.Note
4.3 Compass Calibration
: Home point is the place you first find GPS signal (Red LED status changes from Flashing toSaprkling), with a height of 30 meters above.
1) Entering into the Compass Calibration ModeUnder the manual mode, shiftthe autopilot/manual switch to and fro ten times quickly (back and forth =
one time).then the system will enter the compass calibration state and the
green LED will be constantly on.
2) Horizontal Axis CalibrationWhen the red LED is off, keep the helicopterhorizon (the white LED will be constantly on) and rotate the helicopter 3-4
circles slowly in horizon any direction is OK. When rotating, make the
white LED constantly on as possible as you can. (Refer the video for
compass calibration details). When the calibration of the horizontal axis is
complete, continue on to the vertical axis calibration.
AttentionIf the white LED is off, it means the helicopter deviate from the horizontal
angle too much. Then, users should adjust the position of helicopter, and keepit at the horizontal position and do rotation again. You dont need to re-enterthe calibration mode. Just go on rotating will be OK.
3) Vertical Axis CalibrationWhen erect the helicopter (head down), the redLED will constantly. Then keep the white LED constantly on and rotate the
helicopter 3-4 circles slowly around the longitudinal axis (refer the video of
compass calibration for details).
4) Whether to Save the Calibration Datea) Saving Calibration DataShift the autopilot/manual switch ten times
quickly, then all three LED will flash for 5 seconds, which means the data
has been successfully saved and that you have exited from the
compass calibration mode(the green LED will be off). Please restart the
8/6/2019 DJI Manual
39/54
39
system after the calibration.
b) Quit without SavingIf users dont want to save the new data, shift theautopilot/manual switch once. Then it will abandon the calibration dataand quit from the compass calibration mode (the green LED will be off).
5) Reboot the system6) Inspection after the calibrationIn normal work mode, rotate the helicopter
ten times clockwise, 90for each time, and notice if the white LED is ON or
OFF. Stay 5 seconds between two operations at least
a) Calibration SucceedAfter the all rotations, the white LED must not flashmore than twice(2) out of the 10 rotations;
b) Calibration FailureIf you find that after all rotations, the LED indicatorhas flashed more than 2 out of 10. Then users need to carry out
Compass Calibration once again.
Attention1) Pay attention that there should not be any magnetic or iron materials near
by, such as magnet, vehicles, steel bar under ground etc.2) Ensure that the helicopter is rotated slowly during the calibration, and that
you keep the white LED constantly ON as possible as you can.3) Maintaining the helicopter horizon and rotating it 3-4 circles is that to
guarantee the system can get data for any angle in 360.4) Recalibrationif the following situations occur
a) Any modification of the helicopter, such as the installation of newelectronic equipment, replacement of gyro, the change of MainController installation position, changes of other mechanical structureand the change of battery installation position.
b) In flight, if the helicopter deviates from its flying positions is excessive.c) c) The helicopter frequently turns backward and the White LED
indicator starts to glitter (The White LED can also glitter under normalconditions).
5) DJI-XP3.1 is not suitable to work in Antarctic Circle or Arctic Circle, becausethe magnetic heading system will be invalidation or too close.
4.4 Flight Test under Autopilot ModeThe helicopter can fly normally after all adjustment under manual mode. The
following steps will help users make parameter tuning in autopilot mode to complete
helicopters autopilot flight.
8/6/2019 DJI Manual
40/54
40
4.4.1 Setting Meanings and Related Regulation Methods of Parameters
1. The parameters of autopilot are on the first page of XP configure software
control gain, as shown in Figure 4. 1. At present, 4 parameters on software
layout are opened for fine tuning. Roll_Gain is the parameter for adjusting theroll direction (right-left) movement of helicopter, as shown in Figure 4. 2;
Pitch_Gain is the parameter for adjusting the pitching direction(forward-backward) movement of helicopter, as shown in Figure 4. 3;
Yaw_Gain is the parameter for adjusting the tail rotation direction movementof helicopter, as shown in Figure 4. 4; Vertical_Gain is the parameter foradjusting the vertical direction movement of helicopter, as shown in Figure 4.
5.
Figure 4. 1
Figure 4. 2 Figure 4. 3 Figure 4. 4 Figure 4. 5
Roll Pitch Yaw Vertical
If you want to change the max speed and the acceleration of the system, please
click Advanced, then you can change the value of the max speed and
acceleration in pitch and roll direction (forward and back, left and right). Please
make sure the value is suitable for flying.
8/6/2019 DJI Manual
41/54
41
Before taking off,please read 4.5 Pointsfor attention in flying.Taking off is forbidden
under any unusualcondition
Figure 4. 6Special Tips
The adjustment of the four gain values is similar to the sensitivity adjustmentfor a helicopters tail gyro. If the value is too big, high frequency shaking inaccording direction will occur. If the value is too small, it cannot lock the positionin this direction and drifts side to side slowly.
2. Click Default to restore the default values,and then click write. After writing of default
values, users can attempt their first autopilot
flight with these parameters
3. Users should read through this section beforecarrying out section 4.4.2 flight test! Pleasemake sure the helicopter has a stable hover in
manual mode before switching to the auto mode. Please pay attention to the
helicopter status after entering autopilot. Roll_GainIf there is high frequency shaking in the roll direction (refer to video), it
means Roll_Gain value is too big. Please switch to manual mode in time, land
the helicopter and reduce the according parameter. A coarse tuning can be
about 20 each time.
If left-right cyclic drifting appears (refer to the video), it means the
Roll_Gain is too small. Please switch to manual mode, land the helicopter and
increase this parameter. Regulation methods are the same as above.
Pitch_Gain:Normally, there should be no high frequency shaking in this direction, so
8/6/2019 DJI Manual
42/54
42
users can set a relatively higher value in this direction. Generally speaking, the
value of Pitch_Gain is 1.5 times of Roll-Gain.
Yaw_GainWith the existence of the heading hold gyro and the proper adjustment
of its sensitivity, normally no high frequency shaking or low frequency drifting
will appear in this direction. This value can be understood as Rudder speed,
the higher the faster. But please pay attention, under the auto mode, the tail
speed is relatively slow. So please do not compare it with that under manual
mode. If the value is too big, high frequency shaking of tail will occur.
Vertical_GainIf high frequency shaking happens in the vertical direction (refer to the
video), it means the value of Vertical_Gain is too big. Please switch to manual
mode in time, land the helicopter and reduce the value. The coarse
adjustment can be 3-5each time.
If vertical up-down cyclic drifting appears (refer to the video), it means
the Vertical_Gain is too small. Please switch to manual mode, land the
helicopter and increase this parameter. Regulation methods are the same as
above.
Normal statusWhen parameter tuning is proper in all directions, the helicopter will
maintain a stable hover (refers to the video). Users can try to pull the sticks in
any direction under supervision (one scale is suggested) and watch that the
auto pilot maintains a stable hover and reacts in a short time (hovering to
moving and moving to hovering). If it reacts too slow to start or stop in some
direction when flying, please increase the value in this direction.
Tips: If you find the helicopter loses altitude and descent a little afterbraking, please increase the vertical I on the advanced interface.
Attention1) Two or more phenomenon listed above may appear during adjusting,but please adjust one parameter at one time. After the unusual
phenomenon disappears, adjust the parameter in another direction.2) Normally the gain should be approximately 15% smaller than the critical
value (the value that can just lead the helicopter to the high frequencyshaking). This will ensure that there are no high frequency oscillationsunder various flight statuses (similar to gyro sensitivity tuning).
3) During the adjusting process, please switch to manual mode as soon asany unstable phenomenon occurs.
4) Users can resume the default parameter in control gain at any timethrough software.
8/6/2019 DJI Manual
43/54
43
When first enteringthe autopilot hoveringmode, please preparefor switching to manual
mode momentarily
Please land thehelicopter under
manual mode in everytest flight.
4.4.2 Flying Test
Before flying test, please read 4.5 Points for attention in flying andAppendix F Special Security Checking and then carry on the followingoperations.1. Flying TestUsers must to control helicopter
hovering stable in manual mode before the first
autopilot hovering. And then switch to auto
mode with the autopilot/manual switch of
remote controller, to keep it hovering.
a) Please switch to manual mode at once ifyou notice any unstable phenomenon. After the helicopter enters a
stable hover, you can enter auto mode again.
b) If the helicopter continues to be unstablemore than once when the helicopter
enters auto mode:
Users need to land the helicopterunder manual mode and readjust
relative parameters. Refer to relative tips of adjusting flight
parameters in 4.4.1 Setting Meanings and Related RegulationMethods of Parameters(relative video). Please make sure if the helicopter is adjusted as an ordinaryRC-helicopter. This time, users need to carry out the operations from
the step of 4.1 Helicopter Flying Adjustment and Test underManual Mode.
4.4.3 Flight Success:
Congratulations! If you reach this step successfully, it means your helicopter
can operate normally in Auto pilot mode. For on going maintenance andchecks, you need to read and carry out, 4.5 points for attention in flying in flightand[Appendix F special security checks]and carry out regular check.
4.5Points for Attention in Flying4.5.1Preflight Examination Process
1. Check all connections and electric wires make sure there are no loose joints or
8/6/2019 DJI Manual
44/54
44
Never try to switchto autopilot mode when
the red LED is flashing.
the wires and that they are not wearing against any sharp edges etc.
2. Check that the RC receiver operates normally. Carry out rang checks with theantenna down out to at least 10-20m away from the helicopter and check thatthe servo operate normally.
3. Wait for 3 minutes after power on and examine the starting status of the threeLEDs:
1) There are two situations when system starts successfully:a) With SD CardLEDs will go out orderly. Red White - Greenb) Without SD CardAfter the first LED (red) goes off. The second one
(white) will go off after the first one (red) flashes 5 times continuously. The
green indicator will go off last.
Attention: SD card is suggested because it can be used as a black box2) Starting failure and its solutions:
a) Check all connections first, and turn on the power again.b) If the LEDs do not go off for more than 2 minutes, rebootc) Three LEDs flash simultaneouslyIt means the attitude of controller
starts unsuccessfully. Please lay the helicopter horizontally and power on
again.
d) Three LEDs flash in streamlineIt means reading failure from E2
4. Wait until GPS receives good signals, examine the condition of the red LED:PROM
data. Please reset parameters such as swash type by PC software.
1) Constantly offPerfect signals. Good situation for flying.2) Sparkling Strong signals. Taking off is
allowed, but the safety coefficient decreases,
so users should avoid flying as possible as you
can.
3) FlashingWeak signals. Switching into automode is not allowed. Please recheck the connection of GPS antenna or
adjust at spacious places, so the GPS has clear view of the sky.
Note: when there is no GPS, it is normal phenomenon for swash tilting slowly when the system enters into theauto mode.5. Turn on the remote controller. Then shift the autopilot/manual switch andexamine the condition of the green LED
1) SparklingAutopilot mode2) Flashing 3 times in a groupThere are inputs from Tx in the auto mode,
which means the helicopter receive the velocity command.
3) Constantly offManual mode4) FlashingTx signal lost, and in Fail Safe mode.
6. Switch into the autopilot mode and check if the swash tilts. If it does, rebootsystem.
Note: If the swash moves up and down when entering the auto mode, because the atmospheric pressure is
8/6/2019 DJI Manual
45/54
45
unstable on the ground. It is normal.
7. Manual test: check if the swash plate movement is correct.Note: In auto pilot mode it is normal for the swash plate to have a small operating range, when moving theTx sticks.
8. Rotate the helicopter repeatedly for several times, 90 for each time. Andcheck the condition of the white LED.
9. After no abnormities appear during inspection, start the engine, and examine ifthe LED status indicator has any abnormity (refer to appendix A for details)
10. If no abnormal status appears, users can take off the helicopter manually (redLED must not be flashing).
4.5.2 Flying Attention Points1. These points needing attention before entering auto mode
1) Guarantee the attitude is good (white LED does not lighting).2) When in auto mode, make sure GPS signal is good (red LED does not flash).
Users should avoid flying the helicopter at places with shutters, such as
tunnels, among tall buildings. These shutters will affect the reception of the
GPS signals. It is suitable to fly at spacious places, such as squares.
AttentionEven when the red LED is under the condition of sparkling in flying,users can also switch to auto mode, but the safety coefficient could reduce.So users should avoid flying in such situations. There not effect of the GPSsignal in attitude mode.
3) After hovering by in manual mode, switch to the auto mode. Followings aresome possible problems and solutions
a) Sticks offset from center is not largeIts influence to the system issmall. The system can revise by itself.
b) stick has a large offset from center and the helicopter has tendency todriftShift the manual/autopilot switch to manual mode to make thehelicopter hover stable, and then enter auto mode again.
2. After hovering in manual mode, switch to autopilot mode. Once in auto mode,users can control the helicopter in the directions of up and down, back and
forth, left and right by stick. Shift the autopilot/manual switch at any time will
return the system to manual mode.
8/6/2019 DJI Manual
46/54
46
AttentionPlease do not bump any of the Tx sticks when shifting to autopilot. Or, the
helicopter may not hover, but drift slowly in some direction. And the green LED willflash 3 times in one group. In this situation, users do not need to worry. Please switchto manual mode and then back to auto mode with motionless.
Note:
3. During the auto flight, pay attention to the state of the white LED: Main controller can set the servo value, the time user shift into auto mode, as the feedback center
point.
1) Constantly offGood attitude status.2) SparklingIt means there is a slight error about the attitude computation.
At this time, dont make violent movements with the helicopter. Especially
do not keep the helicopter rotating or accelerating continuously. Or it will
cause the disorder of the attitude computation. So, please keep hovering till
the white LED turns off.
3) Flashinga) If there is no poor sign of loss of control, it does not matter if it flashes
temporarily.
b) If the helicopter shows signs of loss of control, it means the attitudecomputation is unusual. Then users should switch to manual mode and
land the helicopter as soon as possible. Flying after rebooting the
system.
Attention:1) The probability for the white LED to sparkle or flash is small during the
flight. It may happen only when it is bumped or rotates with a highspeed (4 seconds or less per circle) for a long time.
2) Avoid rotation continuously for a long time, for instance: it rotates formore than 3 circles continuously and the speed surpasses 4 seconds percircle.
3) The angular speed should not surpass 3000
4. Exit From Auto ModeGuarantee remote controller can communicatenormally, and users can switch to manual mode and fly normally.
per second in every flightdirection, or problems may occur. In such situation, the system canmake the flight attitude recover automatically, but there may be someerrors during the recovery procedure.
4.5.3Landing Explanation
The helicopter can land under both auto mode and manual mode.
1) Landing Under the Auto Modea) Choose the proper landing position.
8/6/2019 DJI Manual
47/54
47
b) Ensure the helicopter has a stable hover.c) Reduce the collective pitch slowly.d) At the moment of landing, pull the throttle to the lowest point and
switch to the manual mode immediately.
Attention:When close to the ground the helicopter will experience Ground Effect at
approximately 1.5 times the rotor radius and the helicopter will not be stable. It willdrift even under the auto mode. So please do not stay within the Ground Effect fora long time.
2) Landing Under the Manual ModeLanding is the same as an ordinaryremote-control helicopter.
8/6/2019 DJI Manual
48/54
48
3 AppendixAppendix A: LED status indicator
1Normal starting status:1) With SD card: All three LEDs are on, and then go off in the order of red,
white and green.
2) Without SD card: All three LEDs are on. After the red LED goes off. Thewhite one will turn off after the red one flashes 5 times continuously. Thegreen one will turn off at last.
2.Normal status:
Note:1) SparklingOne time per second
2) FlashingFive times per second
3.compass calibration mode:After completeness of the compass calibrationand all three LED flash for five seconds, please restart the system.
Color Red White GreenConstantly
OffVertical axis
Calibration 3
-
ConstantlyOn
Longitudinal
axis
Calibration
Not in proper angle
range
Compass
Calibration
Note:
More than 7 satellites
56 satellite
Less than 5 satellites
3During compass calibration, helicopter tilts from horizon within 3
Color Red White GreenConstantly Off GPS Strong Attitude Good Manual
Sparkling GPS Medium Attitude Medium Autopilot/AttitudeFlashing GPS Weak Attitude Disorder Signal Lost
Flashing 3times per
group
With Velocity
Command in
Constantly On Power Alarm Compass Calibration
http://dict.cnki.net/dict_result.aspx?searchword=%e7%ba%b5%e8%bd%b4&tjType=sentence&style=&t=longitudinal+axishttp://dict.cnki.net/dict_result.aspx?searchword=%e7%ba%b5%e8%bd%b4&tjType=sentence&style=&t=longitudinal+axishttp://dict.cnki.net/dict_result.aspx?searchword=%e7%ba%b5%e8%bd%b4&tjType=sentence&style=&t=longitudinal+axishttp://dict.cnki.net/dict_result.aspx?searchword=%e7%ba%b5%e8%bd%b4&tjType=sentence&style=&t=longitudinal+axis8/6/2019 DJI Manual
49/54
8/6/2019 DJI Manual
50/54
50
Appendix D: Mechanical DrawingThe following units are in millimeters
1. Structure of Main Controller box
8/6/2019 DJI Manual
51/54
51
2. Structure of Adapter box
3. Structure of Anti-vibration Frame
8/6/2019 DJI Manual
52/54
52
Front view of Main Controller in frame
Right view of Main Controller in frame4. Structure of the GPS/Compass unit
8/6/2019 DJI Manual
53/54
53
Appendix E: Packaging ListXP3.1 Standard:1)
2)Main Controller 1piece
3)Adapter 1piece
4)Compass&GPS module 1piece
5)Anti-Vibration Frame 1piece
6)LED Status Indicator 1piece
7)Neoprene Isolators 8pieces
8)DB15 Connection Cable 1piece
9)USB to Serial Cable 1piece
10) SD Card 1piece
Appendix F: Safety Check ListProduct CD 1piece
User should pay special attention to the points listed below, otherwise will leadto Fatal danger!
1. Is adapter installed more than 10cm away from Gas engine, the more thebetter.
2. Is the Fail safe function on the RC transmitter correctly seta) Auto Pilot switch at 0%;
b) Elevator Aileron mid stick;
c) Throttle and pitch mid stick (hover point);
d) Rudder heading hold position.
3. Make sure the Feed back Test and the Controller Orientation Testpassed correctly
4. Have you done the compass calibration, and checked the result thewhite LED should not flash more than twice!
5. Carry out an RC transmitter Range test up to 20m6. Check all DB15 cables are locked in place;7. Ensure that the DB15 cable is not restraining the Neoprene isolators of the
Main Controller;
8. Check all power supplies are secure and plugged in securely;9. Check all servo are plugged in correctly;10. Check blade tracking;11. Ensure there is no excessive vibrations on the helicopter;12. Test flight in manual mode; the helicopter should be able to operate as a
normal helicopter and hover in a stable position.
8/6/2019 DJI Manual
54/54
Appendix G: Frequently Asked QuestionsPlease be careful when carrying out any of the below questions, DJI does not acceptliability for and damage or accident caused as a result of following this advice.Please refer to the website for more FAQ informationo FAQ -Loss of TX signal Answer -If the failsafe is set correctly the heli will hover as usual and theGreen LED will flash for indicating signal lost. We have tried TURN OFF the TX when
flying.o FAQ - Loss of GPS signal
Answer -When flying, loss of GPS signal is a little dangerous andmovement will not occur. The helicopter will be still stable for several seconds
and then start to drift away. There is a new program for loss of GPS signal which
will allow the helicopter to fly stable for up to 30 seconds. The helicopter will be
able to fly under a bridge up to 30m width.o FAQ Warranty Answer -XP 3.1 has a 6 month warrantee and will cover all repairs to maincontroller and Adaptor. This warranty does not cover physical damage due to a
crash or miss handling;
o FAQ - Weight of system Answer - The complete weight of the system is 455 grams (1 pound) thisincludes GPS module, Adaptor and Main Controller;
FAQ Manual override procedures in the event of Motor, ESC or GPSFailure Answer - You should switch to Manual mode as soon as possible and youshould be able to handle these situations in manual control i.e. you may need to
carry out Autorotation recovery procedures.o FAQ Can you take off and land in Auto mode Answer Yes you can but you have to switch to Auto mode at the pointthe helicopter is just about to take off. You will need to be very careful andobserve the behavior. When landing in Auto mode as soon as the helicopter
touches down you need to switch back to manual made ASAP or the engine
may over rev.o FAQ If the system enters fail safe can you set the pitch so that thehelicopter will slowly descend Answer Yes you can set the pitch fail safe position just a little lower thanthe hover point the helicopter will slowly descend hopefully land or at least