The data listed above is approximate and subject to change without notice. Single Conductor DLO • Industrial Motor Lead Cable 14 AWG - 777 KCMIL • 1000 Volts • 90°C Applications These cables were designed for use as motor and power leads where flexi- bility and portability are required. DLO cables are also suitable for use in wiring diesel-electric locomotives, railroad and transit cars, earth moving equipment, offshore drilling rigs, storage batteries, charging equipment and in sizes 1/0 AWG and larger, flexible wiring for installation in conduit or tray per the NEC. Construction Conductor: Class I stranded, tin coated annealed copper per ASTM B-33 and B-172. Separator: A suitable opaque separator tape shall be used over the con- ductor to facilitate stripping. Insulation and Jacket: Black, heavy duty, oil-resistant chlorosulfonated polyethylene (CSPE). Other colors available upon special request. Print Legends: The surface of the jacket shall be printed using white ink and with the following information: Sizes 14 AWG through 1 AWG: “(size) AWG CSPE 1000 VOLTS A.I.W. CORP.” Sizes 1/0 AWG and larger: “(size) AWG (or KCMIL) CSPE Diesel Locomotive Cable 1000 VOLTS IEEE 383---USE or RHH or RHW VW-1 600V. SUN RES FOR CT USE (UL)---A.I.W. CORP.---CSA(Size KCMIL where applicable) AWM I B 90°C 600V FT4---” Note: 262 KCMIL and larger are marked at the next lowest CSA recognized size. (Example: 262 is CSA 250, etc.) 31041 14 19 .070 .060 .200 35 32 30872 12 19 .090 .060 .220 40 42 13570 10 27 .123 .060 .240 55 58 13571 8 37 .156 .080 .325 80 85 13572 6 61 .186 .080 .355 105 126 13573 4 105 .235 .080 .405 140 190 13575 2 147 .315 .080 .490 190 257 13577 1 224 .370 .095 .585 220 386 13578 1/0 273 .405 .095 .620 260 455 13579 2/0 324 .445 .095 .660 300 532 13580 3/0 448 .535 .095 .745 350 714 13581 4/0 532 .545 .095 .800 405 850 13582 262 646 .640 .110 .880 470 1014 13583 313 775 .710 .110 .950 510 1206 13585 373 925 .760 .110 1.000 590 1405 13587 444 1110 .835 .110 1.075 655 1662 13588 535 1332 .870 .125 1.150 730 2016 - 646 1591 .955 .125 1.230 815 2365 13590 777 1924 1.020 .125 1.290 905 2821 Part Number Size AWG or KCMIL Stranding Conductor O.D. (Inches) Insulation Thickness (Inches) Nominal O.D. (Inches) Amps 1 Ship Wt. Lbs./M Ft. 1 Ampacities (amps per conductor) are based on single conductor in free air, 30°C ambient air temperature, 90°C conductor temperature per Table 310.17 of the 2008 NEC. MSHA listed OSHA accepted ES05216 AMERICAN INSULATED WIRE CORP. | 260 Forbes Blvd. | Mansfield, MA 02048 | 1-800-366-2492 Tin Coated
Transcript
The data listed above is approximate and subject to change without notice.
Single Conductor DLO • Industrial Motor Lead Cable14 AWG - 777 KCMIL • 1000 Volts • 90°C
ApplicationsThese cables were designed for use as motor and power leads where flexi-bility and portability are required. DLO cables are also suitable for use inwiring diesel-electric locomotives, railroad and transit cars, earth movingequipment, offshore drilling rigs, storage batteries, charging equipment andin sizes 1/0 AWG and larger, flexible wiring for installation in conduit or trayper the NEC.ConstructionConductor: Class I stranded, tin coated annealed copper per ASTM B-33and B-172.Separator: A suitable opaque separator tape shall be used over the con-ductor to facilitate stripping.Insulation and Jacket: Black, heavy duty, oil-resistant chlorosulfonatedpolyethylene (CSPE). Other colors available upon special request.Print Legends: The surface of the jacket shall be printed using white inkand with the following information:Sizes 14 AWG through 1 AWG: “(size) AWG CSPE 1000 VOLTS A.I.W.CORP.”Sizes 1/0 AWG and larger: “(size) AWG (or KCMIL) CSPE DieselLocomotive Cable 1000 VOLTS IEEE 383---USE or RHH or RHW VW-1600V. SUN RES FOR CT USE (UL)---A.I.W. CORP.---CSA (Size KCMILwhere applicable) AWM I B 90°C 600V FT4---”Note: 262 KCMIL and larger are marked at the next lowest CSA recognizedsize. (Example: 262 is CSA 250, etc.)
1Ampacities (amps per conductor) are based on single conductor in free air, 30°C ambient air temperature, 90°C conductor temperature per Table310.17 of the 2008 NEC.
MSHA listedOSHA accepted
ES05216
AMERICAN INSULATED WIRE CORP. | 260 Forbes Blvd. | Mansfield, MA 02048 | 1-800-366-2492
Tin Coated
The data listed above is approximate and subject to change without notice.
ApplicationsThese cables were designed for use as motor and power leads where flexibility,reduced diameter and portability are required. DLO cables are also suitable foruse in wiring diesel-electric locomotives, railroad and transit cars, earth movingequipment, drilling rigs, storage batteries, charging equipment and flexible wiringfor installation in open air, trays (1/0 and larger) or conduit per the N.E.C.Passes cold bend and impact at -40˚C.ConstructionConductor: Tin-coated annealed copper per ASTM B-33 and B-172 or B-174.Separator (Sizes 4 AWG and larger only): A suitable opaque separator tapeshall be used over the conductor to facilitate stripping.Insulation: Ethylene propylene rubber (EPR) conforming to UL-1581 for ClassEP Table 50.42, UL-44 requirements for RHH and RHW-2, ASTM D-2270 andICEA S-95-658, Class E-1. It shall be suitable for conductor temperatures up to90˚C in wet or dry locations for continuous use, 130˚C for emergency overloads,and 250˚C for short circuits.Jacket: Heavy-duty chlorosulfonated polyethylene (CSPE) conforming to ICEAS-95-658, Par. 4.1.11 and UL-1581 Table 50.1.Print Legends: The surface of the jacket shall be printed using white ink andwith the following information:14 AWG thru 1 AWG: “Size AWG Type RHH or RHW-2 2kV -40˚C VW-1 Sun Res (UL)(E No.)---A.I.W. Corp.---CSA LL8825 RW90 EP/Jkt 1kV -40˚C Oil Res TC FT1---EPR/CSPE2kV Diesel Locomotive Cable P-7K-No.-MSHA”
1/0 AWG thru 1111 KCMIL: “Size AWG (or KCMIL) Type RHH or RHW-2 2kV-40˚C Sun Res for CT use FT4/IEEE-1202 (UL) (E No.)---A.I.W. Corp.---CSA LL8825 (size printed here on 250 & larger only)Type RW90 EP/Jkt -40˚C Oil Res TC 1kV FT4---EPR/CSPE 2kV Diesel Locomotive Cable P-7K-No.-MSHA”
Note: 262 KCMIL and larger are marked at the next lowest CSA recognized size. (Example: 262 is CSA 250, etc.)
Single Cond. DLO • Industrial Motor Lead Cable • Lead-Free14 AWG - 1111 KCMIL • 2000 Volts • 90˚C
1Ampacities (amps per conductor) are based on single conductor in free air, 30˚C ambient air temperature, 90˚C conductor temperature per Table 310.17 of the 2008NEC.
MSHA listedOSHA accepted
ES16744
AMERICAN INSULATED WIRE CORP. | 260 Forbes Blvd. | Mansfield, MA 02048 | 1-800-366-2492
The data listed above is approximate and subject to change without notice.
ApplicationsThese cables were designed for use as motor and power leads where flexibilityand portability are required. DLO cables are also suitable for use in wiringdiesel-electric locomotives, railroad and transit cars, earth moving equipment,offshore drilling rigs, storage batteries, charging equipment and flexible wiringfor installation in open air or conduit per the CEC. Passes cold bend and impactat -40˚C.
ConstructionConductor: Class I stranded, tin-coated annealed copper per ASTM B-33 andB-172.Separator: A suitable opaque separator tape shall be used over the conductorto facilitate stripping.Insulation: Ethylene propylene rubber (EPR) conforming to UL-1309 Type E90(0-2kV) and CSA C22.2 No. 38 requirements. It shall be suitable for conductortemperatures up to 90˚C in wet or dry locations for continuous use, 130˚C foremergency overloads and 250˚C for short circuits.Jacket: Heavy-duty black CSPE conforming to ICEA S-95-658 Par. 4.1.11 and1309 Type CP requirements.Print Legends: The surface of the jacket shall be printed using white ink andwith the following information: “DLO (size) AWG (or KCMIL) 2kV E86047 (UL)Marine Shipboard Cable 90˚C (year)---A.I.W. Corp. P-7K-122015 MSHA---Type
---CSA monogram)LL8825 RW-90 EP 1kV (-40˚C) EP/JKT Oil Res.TC FT1”
Notes:For sizes 1/0 AWG and larger add “For CT Use FT4/ IEEE 1202” after “Sun Res” and substitute “FT4” for “FT1.”
For sizes 262.6 KCMIL and larger add the CSA cable size after “RW-90 EP ” and omit “VW-1.”
CSA cables sizes are rounded off to the next lowest qualifying size. Example: 262.6 KCMIL is CSA size 250 KCMIL.
1Ampacities (amps per conductor) are based on single conductor in free air, 30˚C ambient air temperature, 90˚C conductor temperature per Table 310.17 of the 2008 NEC.
MSHA listedOSHA accepted
ES16273
AMERICAN INSULATED WIRE CORP. | 260 Forbes Blvd. | Mansfield, MA 02048 | 1-800-366-2492
