DLP Projector PH1202HL/PH1002HL - NEC Display … Projector PH1202HL/PH1002HL Installation Manual...

DLP Projector

PH1202HL/PH1002HLInstallation Manual

Model No.NP-PH1202HL, NP-PH1202HLJD, NP-PH1202HL+, NP-PH1002HL+

IntroductionDLP Projector Installation and Adjustment Manual (This document) describes the procedures to install, adjust and maintain the projector PH1202HL/ PH1002HL. For safe and correct installation, adjustment and maintenance of the projector, carefully read this document before considering the layout of the unit and installation. Please keep this document under care by the company who installed or adjusted the projector. This document is intended the readers who have basic knowledge about projector installation. Refer to the user’s manual of an applicable projector for basic operation and remarks.

The product name used in this manualIn this manual, the device name is written as listed below. If the function has difference by devices, the product name is written in the text.

PH1202HL/PH1002HL This product or the projector

Ver. 1 3/15

• HDMI,theHDMILogoandHigh-DefinitionMultimediaInterfacearetrademarksorregisteredtrademarksofHDMILicensing LLC.

• DisplayPortandDisplayPortComplianceLogoaretrademarksownedbytheVideoElectronicsStandardsAssocia-tion.

• HDBaseT™isatrademarkofHDBaseTAlliance.

• DLPisatrademarkofTexasInstruments.

• TrademarkPJLinkisatrademarkappliedfortrademarkrightsinJapan,theUnitedStatesofAmericaandothercountries and areas.

• Blu-rayisatrademarkofBlu-rayDiscAssociation

• CRESTRONandROOMVIEWareregisteredtrademarksofCrestronElectronics,Inc.intheUnitedStatesandothercountries.

• EthernetiseitheraregisteredtrademarkortrademarkofFujiXeroxCo.,Ltd.

• Otherproductnamesandcompanylogosmentionedinthisuser’smanualmaybethetrademarksorregisteredtrademarks of their respective holders.

NOTES(1) The contents of this manual may not be reprinted in part or whole without permission.

(2) The contents of this manual are subject to change without notice.

(3) Great care has been taken in the preparation of this manual; however, should you notice any questionable points, errors or omissions, please contact us.

(4)Notwithstandingarticle(3),NECwillnotberesponsibleforanyclaimsonlossofprofitorothermattersdeemedto result from using the Projector.

i

Important InformationSafety CautionsPrecautionsPleasereadthismanualcarefullybeforeusingyourNECprojectorandkeepthemanualhandyforfuturereference.

CAUTIONTo turn off main power, be sure to remove the plug from power outlet.The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

CAUTIONTOPREVENTSHOCK,DONOTOPENTHECABINET.THEREAREHIGH-VOLTAGECOMPONENTSINSIDE.REFERSERVICINGTOQUALIFIEDSERVICEPERSONNEL.

Thissymbolwarnstheuserthatuninsulatedvoltagewithintheunitmaybesufficienttocauseelectricalshock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided.The information should be read carefully to avoid problems.

WARNING:TOPREVENTFIREORSHOCK,DONOTEXPOSETHISUNITTORAINORMOISTURE.DONOTUSETHISUNIT’SPLUGWITHANEXTENSIONCORDORINANOUTLETUNLESSALLTHEPRONGSCANBEFULLYINSERTED.

DOC Compliance Notice (for Canada only)ThisClassAdigitalapparatusmeetsallrequirementsoftheCanadianICES-003Standards.

Machine Noise Information Regulation - 3. GPSGV,Thehighestsoundpressurelevelislessthan70dB(A)inaccordancewithENISO7779.

Disposing of your used product

EU-widelegislationasimplementedineachMemberStaterequiresthatusedelectricalandelectronicprod-ucts carrying the mark (left) must be disposed of separately from normal household waste. This includes projectorsandtheirelectricalaccessories.Whenyoudisposeofsuchproducts,pleasefollowtheguidanceof your local authority and/or ask the shop where you purchased the product.After collecting the used products, they are reused and recycled in a proper way. This effort will help us reduce the wastes as well as the negative impact to the human health and the environment at the minimum level.ThemarkontheelectricalandelectronicproductsonlyappliestothecurrentEuropeanUnionMemberStates.

WARNINGThis is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CAUTION• Inordertoreduceanyinterferencewithradioandtelevisionreceptionuseasignalcablewithferritecoreattached.Useofsignalcableswithoutaferritecoreattachedmaycauseinterferencewithradioandtelevisionreception.• ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,pursuanttoPart

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radi-ate radio frequency energy and, if not installed and used in accordance with the installation manual, may cause harmfulinterferencetoradiocommunications.Operationofthisequipmentinaresidentialareaislikelytocauseharmful interference in which case the user will be required to correct the interference at his own expense

ii

Important Information

WARNING TO CALIFORNIA RESIDENTS:Handlingthecablessuppliedwiththisproductwillexposeyoutolead,achemicalknowntotheStateofCaliforniatocausebirthdefectsorotherreproductiveharm.WASHHANDSAFTERHANDLING.

ForUKonly:InUK,aBSapprovedpowercordwithmouldedplughasaBlack(15Amps)fuseinstalledforusewiththis equipment. If a power cord is not supplied with this equipment please contact your supplier.

Important SafeguardsThesesafetyinstructionsaretoensurethelonglifeofyourprojectorandtopreventfireandshock.Pleasereadthemcarefully and heed all warnings.

Installation• Consultyourdealerforinformationabouttransportingandinstallingtheprojector.Donotattempttotransportandinstalltheprojectoryourself.Theprojectormustbeinstalledbyqualifiedtechniciansinordertoensureproperop-eration and reduce the risk of bodily injury.• Donotplacetheprojectorinthefollowingconditions:

- on an unstable cart, stand, or table.- near water, baths, or damp rooms.- in direct sunlight, near heaters, or heat radiating appliances.- in a dusty, smoky or steamy environment. - on a sheet of paper or cloth, rugs or carpets.• Donotinstallandstoretheprojectorinthebelowcircumstances.Failuretodosomaycauseofmalfunction.- Inpowerfulmagneticfields- In corrosive gas environment- Outdoors• Ifyouwishtohavetheprojectorinstalledontheceiling:

- Do not attempt to install the projector yourself.- Theprojectormustbeinstalledbyqualifiedtechniciansinordertoensureproperoperationandreducetherisk

of bodily injury.- In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance

with any local building codes.- Please consult your dealer for more information.

iii


WARNING• Donotcoverthelenswiththelenscaporequivalentwhiletheprojectorison.Doingsocanleadtomeltingof

the cap due to the heat emitted from the light output.

• Donotplaceanyobjects,whichareeasilyaffectedbyheat,infrontoftheprojectorlens.Doingsocouldleadto the object melting from the heat that is emitted from the light output.

Do not use the projector with it leaning to the left and right. This may result in a malfunction, however, portrait instal-lation* is possible. Please read the warnings concerning portrait orientation before setting the projector in portrait orientation. (→ page 2)

Fire and Shock Precautions • Ensurethatthereissufficientventilationandthatventsareunobstructedtopreventthebuild-upofheatinsideyour

projector. Allow enough space between your projector and a wall. (→ page 1)• Preventforeignobjectssuchaspaperclipsandbitsofpaperfromfallingintoyourprojector.Donotattempttoretrieve

any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualifiedservicepersonnel.• Donotplaceanyobjectsontopoftheprojector.• Donottouchthepowerplugduringathunderstorm.Doingsocancauseelectricalshockorfire.• Theprojectorisdesignedtooperateonapowersupplyof200-240VAC50/60Hz.Ensurethatyourpowersupplyfitsthisrequirementbeforeattemptingtouseyourprojector.• Donotlookintothelenswhiletheprojectorison.Seriousdamagetoyoureyescouldresult.• Donotlookintothelightsourceusingopticalinstruments(suchasmagnifyingglassesandmirrors).Visualimpair-

ment could result.• Whenturningontheprojector,makesurenoonewithinprojectionrangeislookingatthelens.

• Keepanyitems(magnifyingglassetc.)outofthelightpathoftheprojector.Thelightpathbeingprojectedfromthe

lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause anunpredictableoutcomesuchasafireorinjurytotheeyes.

iv


• Handlethepowercordcarefully.Adamagedorfrayedpowercordcancauseelectricshockorfire.- Do not use any power cord other than the one supplied with the projector.- Do not bend or tug the power cord excessively.- Do not place the power cord under the projector, or any heavy object.- Do not cover the power cord with other soft materials such as rugs.- Do not heat the power cord.- Do not handle the power plug with wet hands.• Turnofftheprojector,unplugthepowercordandhavetheprojectorservicedbyaqualifiedservicepersonnelunderthefollowingconditions:- Whenthepowercordorplugisdamagedorfrayed.- If liquid has been spilled into the projector, or if it has been exposed to rain or water. - If the projector does not operate normally when you follow the instructions described in this user’s manual.- If the projector has been dropped or the cabinet has been damaged.- If the projector exhibits a distinct change in performance, indicating a need for service.• Disconnectthepowercordandanyothercablesbeforecarryingtheprojector.• Movingtheprojectorrequiresfourpeopleormore.Besuretofirmlygripthefrontandbackhandles,thenmovethe

projector.• Turnofftheprojectorandunplugthepowercordbeforecleaningthecabinet.• Turnofftheprojectorandunplugthepowercordiftheprojectorisnottobeusedforanextendedperiodoftime.• WhenusingaLANcable: For safety, do not connect to the terminal for peripheral device wiring that might have excessive voltage.

CAUTION• Keephandsawayfromthelensmountingportionwhilethelensshiftisinoperation.Failuretodosocouldresultinfingersbeingpinchedbetweenthecabinetandlenscover.• Donotusetheleveladjusterforpurposesotherthanoriginallyintended.• Donotunplugthepowercordfromthewalloutletorprojectorwhentheprojectorispoweredon.Doingsocan

cause damage to the AC IN terminal of the projector and (or) the prong plug of the power cord. To turn off the AC power supply when the projector is powered on, use the projector’s main power switch, a power

strip equipped with a switch, or a breaker.

Precautions when installing or replacing the lens unit sold separately (LENS CALIBRATION)Afterinstallingorreplacingthelensunit,presseithertheLENSCALIBRATIONbuttononthemainunitortheINFO/L-CALIB.buttonwhilepressingtheCTLbuttonontheremotecontroltocarryout[LENSCALIBRATION].(→ page 26)Bycarryingout [LENSCALIBRATION], theadjustment rangeof thezoomand focusof the [LENSMEMORY] iscalibrated.Contact your dealer to install and replace the lens unit.

Caution on Handling the Optional LensWhenshippingtheprojectorwiththelens,removethelensbeforeshippingtheprojector.Alwaysattachthedustcapto the lens whenever it is not mounted on the projector. The lens and the lens shift mechanism may encounter damage caused by improper handling during transportation. If you need to remove the lens unit, contact your dealer.

v


Remote Control Precautions• Handletheremotecontrolcarefully.• Iftheremotecontrolgetswet,wipeitdryimmediately.• Avoidexcessiveheatandhumidity.• Donotshort,heat,ortakeapartbatteries.• Donotthrowbatteriesintofire.• Ifyouwillnotbeusingtheremotecontrolforalongtime,removethebatteries.• Ensurethatyouhavethebatteries’polarity(+/−)alignedcorrectly.• Donotusenewandoldbatteriestogether,orusedifferenttypesofbatteriestogether.• Disposeofusedbatteriesaccordingtoyourlocalregulations.

Light Module

1. A light module containing multiple laser diodes is equipped in the product as the light source.

2. These laser diodes are sealed in the light module. No maintenance or service is required for the performance of the light module.

3. Enduserisnotallowedtoreplacethelightmodule.

4. Contactqualifieddistributorforlightmodulereplacementandfurtherinformation.

Laser Safety Caution• Thelasermoduleisequippedinthisproduct. Useofcontrolsoradjustmentsofproceduresotherthanthosespecifiedhereinmayresultinhazardousradiation

exposure.• ThisproductisclassifiedasClass1ofIEC60825-1Thirdedition2014.Obeythelawsandregulationsofyourcountry

in relation to the installation and management of the device. Bluepumpinglaserdiodes:Wavelength448nm,Outputpower300W Bluelaserdiodes:Wavelength462nm,Outputpower56W• Donotlookintothelenswhiletheprojectorison.Seriousdamagetoyoureyescouldresult.Payenoughattention

to children.• Thebelowdiagramisindicatedontheprojector.

• Donotlookintothelightsourceusingopticalinstruments(suchasmagnifyingglassesandmirrors).Visualimpair-

ment could result.• Whenturningontheprojector,makesurenoonewithinprojectionrangeislookingatthelens. DONOTSTAREINTOTHELENSWHILEINUSE.

vi


• Thelabelisstuckonthebelowindicatedposition.

Label

vii


Radiation range of emitted light by the projector (HD: Hazard distance)• ThebelowtabledescribestheradiationrangeofemittedlightbytheprojectorthatisclassifiedasRiskGroup3(RG3)ofIEC62471.

• Pleasekeepwithinboundsforinstallingtheprojector. Install a barrier for preventing human eyes from entering the RG3 area. Forthebarrierinstallationposition,keephorizontalsafetyzoneover1.5mfromtheRG3area. In case to install the projector over head, keep over 3m distance at least between the floor surface and the RG3

area.

Lens Zoom HD(m) H(m) V(m)

NP-9LS08ZM1Wide 0.7 0.79 0.42

Tele 1.4 1.08 0.57

NP-9LS12ZM1Wide 1.8 1.41 0.75

Tele 2.3 1.29 0.68

NP-9LS13ZM1Wide 1.9 1.36 0.72

Tele 3.0 1.40 0.74

NP-9LS16ZM1Wide 2.7 1.62 0.85

Tele 3.7 1.37 0.72

NP-9LS16Z1Wide 2.6 1.58 0.83

Tele 3.4 1.63 0.86

NP-9LS20ZM1Wide 3.8 1.78 0.94

Tele 3.0 0.75 0.40

NP-9LS20Z1Wide 2.8 1.37 0.72

Tele 3.6 1.32 0.70

NP-9LS40ZNP-9LS40ZM1

Wide 7.8 1.90 1.00

Tele 10.1 1.59 0.84

H

V

HD

[Plan view]

[Side view]

RG3 range

*Iflensshiftisutilized,pleaseconsidertheshiftofprojectedimageaccordingtothevolumeoflensshift.

viii


CautionPlease heed all precaution for safety.

To install the projector• Forplanningthelayoutoftheprojector,makesuretotakesafetymeasuresinstructedontheinstallationmanu-

al.• Inordertorefusedanger,installeitherawalloutletwithineasyreachforpullingoutthepowerpluginemergency

or a device as a breaker to shut down the power supply to the projector.• TakesafetymeasurespreventinghumaneyesfromenteringtheRG3area.• Consideringtheinstallationplace,selectanappropriatelensandsecuresafetyzonethatisdeterminedforeach

lens. For operation on the powered projector as light adjustment, make sure appropriate safety measures have been taken.• Checkthevalidityoftakensecuritymeasuresifappropriatesafetyzonebasedontheinstalledlensissecured.

Periodically check the validity and keep these results.• Educatetheadministratoroftheprojector(operators)aboutsafetybeforestartingtooperatetheprojector.

To use the projector• Instructtheadministratoroftheprojector(operators)toperforminspectionsbeforepoweringontheprojector.

(Including the safety check against emitted light by the projector)• Instructtheadministratoroftheprojector(operators)tobeincircumstancesabletocontroltheprojectorwhenever

the projector is powered on for an emergency.• Instructtheadministratoroftheprojector(operators)tokeeptheinstallationmanual,user’smanualandinspec-

tion records to a place where they can take these documents out easily.• Instructthemtoclarifyiftheprojectorisconformedtostandardsofeachcountryandregion.

About High Altitude mode• Usingtheprojectorathighlandscanshortenthelifeofopticalcomponentssuchasthelightmodule.

About Copyright of original projected pictures:Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with the following func-tions may raise concern about the infringement of copyrights which are protected by copyright law.[ASPECTRATIO],[KEYSTONE],Magnifyingfeatureandothersimilarfeatures.

Turkish RoHS information relevant for Turkish marketEEE Yönetmeliğine Uygundur.

Thisdeviceisnotintendedforuseinthedirectfieldofviewatvisualdisplayworkplaces.Toavoidincommodingreflec-tionsatvisualdisplayworkplacesthisdevicemustnotbeplacedinthedirectfieldofview.

ix


Health precautions to users viewing 3D images

Beforeviewing,besuretoreadhealthcareprecautionsthatmaybefoundintheuser’smanualincludedwithyour3Deyeglassesoryour3DcompatiblecontentsuchasBlu-rayDiscs,videogames,computer’svideofilesandthelike.Toavoidanyadversesymptoms,heedthefollowing:• Donotuse3Deyeglassesforviewinganymaterialotherthan3Dimages.• Allowadistanceof2m/7feetorgreaterbetweenthescreenandauser.Viewing3Dimagesfromtooclosea

distance can strain your eyes.• Avoidviewing3Dimagesforaprolongedperiodoftime.Takeabreakof15minutesorlongeraftereveryhour

of viewing.• Ifyouoranymemberofyourfamilyhasahistoryoflight-sensitiveseizures,consultadoctorbeforeviewing3D

images.• Whileviewing3Dimages,ifyougetsicksuchasnausea,dizziness,queasiness,headache,eyestrain,blurry

vision, convulsions, and numbness, stop viewing them. If symptoms still persist, consult a doctor. • View3Dimagesfromthefrontofthescreen.Viewingfromananglemaycausefatigueoreyestrain.

Power management functionIn order to keep power consumption low, the following power management functions (1) and (2) have been set when shipped from the factory. Please display the on-screen menu and change the settings (1) and (2) according to the aim of using the projector.

1. STANDBY MODE (Factory preset: NORMAL)

• When[NORMAL]isselectedfor[STANDBYMODE],thefollowingterminalsandfunctionswillnotwork:

HDMIOUTterminal,Ethernet/HDBaseTPort,USBPort,LANfunctions,MailAlertfunction

(→ page 39)

2. AUTO POWER OFF (Factory preset: 1 hour)

• When[1:00]isselectedfor[AUTOPOWEROFF],youcanenabletheprojectortoautomaticallyturnoffin1hourifthereisnosignalreceivedbyanyinputorifnooperationisperformed.

(→ page 51)

Clearance for Installing the ProjectorAllow ample clearance between the projector and its surroundings.The high temperature exhaust coming out of the device may be sucked into the device again.Avoid installing the projector in a place where air movement from the HVAC is directed at the projector.Heated air from the HVAC can be taken in by the projector's intake vent. If this happens, the temperature inside the projector will rise too high causing the over-temperature protector to automatically turn off the projectors power.• Beforesettingtheprojectorinportraitorientation,pleasereadpage2.

x

Table of Contents

Introduction .................................................................................................................b

The product name used in this manual .....................................................................b

Important Information ............................................................................................ i

1. Before Setting Up Your Projector .............................................................1

1-1. Clearance for Installing the Projector ...........................................................................1

1-2. Installation for Tilt-free and Portrait projection ..............................................................2

1-3.Selectingthelensunit ..................................................................................................5

1-4. Carrying the projector ..................................................................................................8

1-5. List of used tools ..........................................................................................................8

1-6.Mounting/Removingthelenscover ............................................................................9

2. Setting Up Your Projector ...........................................................................10

2-1.SetupProcedure ........................................................................................................10

2-2. Installing the projector ................................................................................................11

2-2-1. Adjustment of the projector’s settings (Level adjusters) ................................11

2-2-2. Install the projector on the ceiling .................................................................12

2-2-3.Multi-ScreenProjection .................................................................................13

2-3. Connecting the Power Cord .......................................................................................17

UsingthePowerCordFixingMetal .........................................................................18

2-4.MountingtheLensUnit ..............................................................................................19

Lens unit mounting method.....................................................................................20

2-5.MountingtheOptionalBoard(soldseparately) ..........................................................22

3. Projector Adjustment and Connecting ................................................24

3-1. Flow of Adjustment and Connecting ..........................................................................24

3-2. Turning on the Projector .............................................................................................25

3-3.Selectingtheprojectororientation .............................................................................28

3-4.AdjustingthePictureSizeandPosition ......................................................................29

3-5.ConnectingtoOtherEquipments ...............................................................................35

3-5-1. Connecting a computer .................................................................................35

3-5-2.ConnectinganExternalMonitor ...................................................................39

3-5-3.ConnectingYourBlu-rayPlayerorOtherAVEquipment ...............................40

3-5-4. Connecting a document camera ...................................................................43

3-5-5.ConnectingtoaWiredLAN ..........................................................................44

3-5-6.ConnectingtoaHDBaseTtransmissiondevice(soldcommercially)............45

3-6.OptimizingComputerSignalAutomatically ................................................................46

xi

Table of Contents

4. List of Menu Items ..........................................................................................47

5. Maintenance .......................................................................................................53

5-1. Cleaning the Filters ....................................................................................................53

5-2. Cleaning the Lens ......................................................................................................57

5-3. Cleaning the Cabinet..................................................................................................57

6. Appendix ................................................................................................................58

6-1.CompatibleInputSignalList ......................................................................................58

6-2.Troubleshooting ..........................................................................................................61

Indicator Messages .................................................................................................61

6-3.Pinassignmentsandsignalnamesofmainterminals ...............................................63

6-4.CabinetDimensions ...................................................................................................71

1

1. Before Setting Up Your Projector1-1. Clearance for Installing the ProjectorAllow ample clearance between the projector and its surroundings as shown below.Avoid installing the projector in a place where air movement from the HVAC is directed at the projector.Heated air from the HVAC can be taken in by the projector’s intake vent. If this happens, the temperature inside the projector will rise too high causing the over-temperature protector to automatically turn off the projectors power.

Installation conditions for the projector

Example 1 – If there are walls on both sides of the projector.The drawing shows the proper clearance required for the front, back and top of the projector.

30 cm/11.8"or greater


Ventilation(inlet)

Ventilation(inlet)

Example 2 – If there is a wall behind the projector.The drawing shows the proper clearance required for the front, sides and top of the projector.(1)Forfloorinstallation:


Ventilation(outlet)

Lens

(2)Forceilingmounting:



Lens

2

1. Before Setting Up Your Projector

1-2. Installation for Tilt-free and Portrait projectionThis projector can be set to any anglewithin a vertical 360° range,however, it cannot be installed with right or left slant besides the portrait projection.If you install the projector vertically you can project screens from your computer and other sources in portrait orientation.

Precautions for the portrait insntallation• Donotsimplysettheprojectorverticallyonthefloororonatable.Theprojectormayfallover,resultingininjury,

damage or malfunction. Also the intake vent may become blocked causing the unit’s internal temperature to riseresultinginmalfunctionandriskoffire.

• Forportraitinstallationtheintakeventsmustbeinstalledatthetopandbottom.Toensureairflowtothebottomintake vent, a rack to support the unit is necessary. Please hire an installation service provider (for a fee) to make a custom portrait projection stand.

• Wheninstalledinportraitorientationtheprojectorcanbetiltedforwardorbackward

withinarangeof±10°.Tiltingtheprojectorforwardorbackwardoutsideofthisrange,ortiltingittotheleftorto the right could cause it to malfunction.

• Toensureairflow,maintain30cm/11.8"ofspacebetweentheintakevent and the installation surface.

(NOTE)Inthefiguretotherightthereisplentyofspacebehind,above,and on either side of the projector unit.

Intakevent

Intakevent

30c

m/1

1.8"

or

grea

ter

3


Caution to the installation for the Tilt-free projection• Donotinstalltheprojectorinthestateoffacingup/downorinclineddirectlyonafloorandatable.Iftheprojector

falls down, It may cause of malfunction, damage and human injury. If the intake vents are obstructed, the projector insidetemperaturewillincreaseanditmaycauseofmalfunctionandfire.

• Makesuretoproducethesupportmetal for theprojectorastheceilingmountmetal. Pleaseasktheservicecompany about the support metal production. (for a fee)

• Incaseyouneedtoinstalltheprojectorintiltedangle,pleaseinstalltheprojectorbysupportmetalsthathaveenough durability to support the projector for a long time.

Design and manufacturing conditions for a stand and a ceiling mount metal of the projectorPleasehireaninstallationserviceprovider(forafee)todesignandmanufacturecustomizedstandandceilingmountmetal.Pleaseensurethatthedesigncomplieswiththefollowingconditions:• Thereisoneintakeventoneithersideandoneexhaustventattherear.Theseshouldremainunobstructed.Also,secureenoughspaceforeasyfiltercoverremovalforfiltercleaning.

• Removetheleveladjustersortheprojectorhandlesincasethesehitagainstthestand.Forremovingtheleveladjuster, rotate the level adjuster itself, and for removing the handle, remove the handle fastening screws.

• Fixthestandontotheceilingmountscrewholes(6positions)ontheprojectorbottomface.

Dimensionsofscrewhole:forM6screwMaximumdepth10mm(Calculatetheboltlengthdependingonthestanddesign)

• Horizontaladjustmentmechanism(forexample,boltsandnutsin4places)

• Makesuretodesignthestandnotfallingovereasily.

• Makesureiftheprojectorisfixedonthesurfacethathasenoughdurabilitytostandthewholeprojectorweight(theprojectorweight68kgplusthelensweight3kg,i.e.,71kgintotal)foralongtime.

Referential drawings for the portrait projection* Figure illustrating the dimensions and conditions (not actual design blueprint).

150 150 300

140

140

[Side View] [Front View]

6 - M6 bolt(Unit: mm)

Horizontal adjuster

Exhaust vent

Intake vent

Intake vent

4


CAUTION• Whenmovingtheprojector,makesureyouhaveatleastfourpeople.Attemptingtomovetheprojectoralone

could result in back pain or other injuries.

5


1-3. Selecting the lens unitThissectionprovidestheguidelineinformationonhowtoselectascreensize,projectormountingposition,andtypeof lens units, which is appropriate for your presentation purposes. Many types of optical lens for the projector are available for separate sale to support various projection range.Notethatalldescriptionsgiveninthismanualassumethattheangleofprojectioniszerodegree.Incaseofprojectionfrom an upper position or from the right or left, it is necessary to calculate the width for the minimum projected image thatisalittlelargerthanthescreensize.

Minimum width

ScreenScreen

Minimumheight

Projectedimage Projected

image

Throw distance and screen sizeSixseparatebayonetstylelensescanbeusedonthisprojector.Refertotheinformationonthispageandusealenssuitedfortheinstallationenvironment(screensizeandthrowdistance).Forinstallationandreplacementoflensunitscontact your dealer.Eachnumberprovidedinthetablebelowmeansthethrowdistancebetweenthelenssurfaceandthescreen.

Lens types and throw distanceunit = m

Screensize Lens model nameNP-9LS08ZM1 NP-9LS12ZM1 NP-9LS13ZM1 NP-9LS16ZM1 NP-9LS20ZM1 NP-9LS40ZM1

60" — — — — — 5.8–9.170" 1.4–2.1 — — — — 6.7–10.5100" 2.0–3.0 2.8–4.0 3.1–4.9 3.8–6.3 5.0–9.3 9.6–15.0120" 2.4–3.6 3.4–4.8 3.7–5.9 4.5–7.6 6.0–11.1 11.5–18.0150" 3.0–4.5 4.2–6.0 4.7–7.4 5.7–9.5 7.5–13.9 14.3–22.5200" 4.0–6.0 5.6–8.1 6.2–9.9 7.6–12.7 9.9–18.5 19.0–29.9250" 5.0–7.5 7.0–10.1 7.8–12.4 9.5–15.9 12.4–23.1 23.8–37.4300" 6.0–9.0 8.5–12.1 9.4–14.9 11.4–19.1 14.8–27.7 28.5–44.9350" 7.0–10.6 9.9–14.2 11.0–17.4 13.3–22.3 17.3–32.3 33.3–52.3400" 8.0–12.1 11.3–16.2 12.5–19.8 15.2–25.5 19.8–36.9 38.0–59.8450" 9.0–13.6 12.7–18.2 14.1–22.4 17.1–28.9 22.2–41.5 42.7–67.2500" 10.0–15.1 14.1–20.2 15.7–24.8 19.0–31.9 24.7–46.1 47.5–74.7550" 11.1–16.6 — — — — —600" 12.1–18.1 — — — — —

TIP• Calculationofthethrowdistancefromthescreensize NP-9LS08ZM1lensthrowdistance(m)=H×0.90toH×1.35:1.4m(min.)to18.1m(max.) NP-9LS12ZM1lensthrowdistance(m)=H×1.28toH×1.83:2.8m(min.)to20.2m(max.) NP-9LS13ZM1lensthrowdistance(m)=H×1.42toH×2.24:3.1m(min.)to24.8m(max.) NP-9LS16ZM1lensthrowdistance(m)=H×1.73toH×2.88:3.8m(min.)to31.9m(max.) NP-9LS20ZM1lensthrowdistance(m)=H×2.23toH×4.16:5.0m(min.)to46.1m(max.) NP-9LS40ZM1lensthrowdistance(m)=H×4.34toH×6.76:5.8m(min.)to74.7m(max.) “H”(Horizontal)referstothescreenwidth. *Figuresdifferbyseveral%withthetableabovebecausethecalculationisapproximate. Ex.:Throwdistancewhenprojectingona300"screenusingtheNP-9LS13ZM1lens: Accordingtothe“Tablesofscreensizesanddimensions”(→page6),H(screenwidth)=664.1cm. Thethrowdistanceis6.641cm×1.42to6.641cm×2.24=9.430cmto14.876cm(becauseofthezoomlens).

Projectionfromtheleft Projectionfromanupperposition

6


Projection range for the different lenses

60-500"

100-500" 100-500" 100-500"

NP-9LS20ZM1 5.0–46.1 m

70-600"

100-500"

NP-9LS08ZM1 1.4–18.1 m

NP-9LS13ZM1 3.1–24.8 m

NP-9LS16ZM1 3.8–31.9 m

NP-9LS40ZM1 5.8–74.7 m

NP-9LS12ZM1 2.8–20.2 m

Tables of screen sizes and dimensions

Screenheight

Screenwidth

16:10screensize (diagonal)

Size(inches) Screenwidth Screenheight(inches) (cm) (inches) (cm)

60 52 132.8 29 74.770 61 155.0 34 87.2

100 87 221.4 49 124.5150 131 332.1 74 186.8200 174 442.8 98 249.1250 218 553.5 123 311.3300 261 664.1 147 373.6350 305 774.8 172 435.8400 349 885.5 196 498.1450 392 996.2 221 560.4500 436 1106.9 245 622.6550 479 1217.6 270 684.9600 523 1328.3 294 747.2

7


Lens shifting rangeThisprojectorisequippedwithalensshiftfunctionforadjustingthepositionoftheprojectedimagebyusingtheLENSSHIFTbuttons(→ page 31). The lens can be shifted within the range shown below.

NOTE:• Pleasedonotusethelensshiftfunctionwhenprojectingportraitimages.Pleaseuseitwiththelensinthecenter.

Legend:V“Vertical”referstothescreenheightandH“Horizontal”referstothescreenwidth.Thelensshiftrangeisexpressed as a ratio of height and width, respectively.

Compatible lens unitsNP-9LS08ZM1,NP-9LS12ZM1,NP-9LS13ZM1,NP-9LS16ZM1,NP-9LS20ZM1

100%V

50%V20%V 20%V

20%V20%V50%V

100%H

11%H 11%H

11%H11%H

Heightofprojectedimage

Widthofprojectedimage

Compatible lens unitNP-9LS40ZM1

100%V

55%V

50%V

100%H

11%H 11%H

11%H11%H



* The lens shift range is the same for ceiling installation.

(Examplecalculation)Ifprojectingona300inchscreenusinganNP-9LS13ZM1lensunitAccordingtothe“Tableofscreensizesanddimensions”(→ page 6),H=261.5"/664.1cm,V=147.1"/373.6cm.Adjustment range in thevertical direction: theprojected imagecanbemovedupwards0.5×147.1"/373.6cm≈ 73.6"/187cm,downwardsapproximately73.6"/187cm(whenthelensisatthecenterposition).Adjustmentrangeinthehorizontaldirection:theprojectedimagecanbemovedtotheleft0.11×261.5"/664.1cm≈28.7"/73cm,totherightapproximately28.7"/73cm.* Figures differ by several % because the calculation is approximate.

8


1-4. Carrying the projectorWhenmoving theprojector, it shouldbecarriedbyholding thehandleson thebaseof theunitby fourormorepeople.

WARNING:Whenmovingtheprojector,firstturnoffthepowerandalwaysdisconnectthepowerplugfromtheelectricaloutlet,and check that all of the connecting cables between equipment and the lenses have been removed.

Handlefortransportation(front) Handlefortransportation(rear)

1-5. List of used toolsThe tools used to install the projector and the laser unit are listed below.

Lens unit

Tool Main application

Servicekey Mounting and removing the lens cover (supplied with the projector)

Option board

Tool Main application

Phillips head screwdriver (No.2) Installation and removal of the optional board

9


1-6. Mounting / Removing the lens coverThis section provides guideline information on how to mount and remove covers on the projector.

Name of the cover

Lens coverKey lock

Place for putting your hand

NOTE:• Thelenscoverequipsthekeylock.Theservicekeyisrequiredtomountorremovethelenscover.• Oncethelenscoverisremoved,theprotectivecircuitisactivated. Makesuretomountthelenscoversecurely.Thesetmetalsareequippedalsoatthelensleftandrightsides.Pushthesidesoflensformountingthelenscoversecurely.

• Donotpowerontheprojectorwithoutmountingthelenscover.• Whenremovingorinstallingthelenscover,returnthepositionofthelenstothecenterbeforeturningoffthepowertotheprojec-tor(Seepage31).

Preparation:Servicekey(suppliedwiththeprojector)

1. Unlock the lens cover.

Unlockthecoverusingtheservicekey.

1

2

2

2. Remove the lens cover.

Thelenscoverissecuredtotheprojectorbodybytwoclawseachatthecovertopandbottomandoneclawatthesideoflens.

Holdthecoversidesandpulltowardyou.

This completes removing the lens cover. To mount the cover, perform the removal procedure in reverse. Make sure to lockthekey.Ifthecoverisnotproperlymounted,anerrormayoccur.Securelypushallfiveclawsintotheposition.

*Lenscoverremovedcondition

10

2-1. Setup ProcedureSetuptheprojectoraccordingtotheprocedurebelow.Thischapterdescribestheinstallationofprocedureuntilturn-ing on of the power.

Step 1• Installtheprojector(→ page 11)

Step 2 • Connectthepowercordtotheprojector(→ page 17)

Step 3 • MountingtheLensUnit(→ page 19)

Step 4• Mountingtheoptionboards(→ page 22)

2. Setting Up Your Projector

11


2-2. Installing the projector

2-2-1. Adjustment of the projector’s settings (Level adjusters)The projector must be placed square to the screen otherwise keystone distortion may appear on the screen. For set-tingtheprojectorperpendiculartothescreenwhenviewedfromtheside,utilizingtheleveladjustersequippedateachcorneroftheprojectorbottom.MaximumAdjustablelengthoftheleveladjusteris10mm/0.39".

Example for adjustment

Raise Raise

Lower Lower

Leveladjuster

NOTE:• Donotlengtheneachleveladjusterlongerthan10mm/0.39".Theforceofdoingsomaycausetheleveladjustertocomeoff,resultingindamagetotheprojector.

• Payattentiontolengthenorshortentwoleveladjustersatfrontatthesametime.Samefortherearadjusters,otherwise,theweightoftheprojectorisloadedononeleveladjusteranditmaycauseofdamagetoit.

12


Unit:mm(inch)

150

(5.9

)15

0 (5

.9)

300

(11.

8)

140 (5.5)140 (5.5)

2-2-2. Install the projector on the ceilingReferthebelowindicatedspecificationsinordertoinstalltheprojectorontheceiling.

6-M6screwMaximumdepth10mm

13


2-2-3. Multi-Screen Projection

Things that can be done using multi-screen projectionThis projector can be used singly or arranged in multiple units for multi-screen projection.Wewillintroduceanexampleusingtwoprojectionscreenshere.

Case 1Usingasingleprojectortoprojecttwotypesofvideosatthesametime[PIP/PICTUREBYPICTURE]

Case 2Usingfourprojectors(resolution:FULLHD)toprojectvideowitharesolutionof3840×2160pixels[TILING]

Case 1. Using a single projector to project two types of videos [PIP/PICTURE BY PICTURE]Connection example and projection image

Inthecaseof[PICTUREBYPICTURE] Inthecaseof[PIP]

On-screen menu operationsDisplay[DISPLAY]→[PIP/PICTUREBYPICTURE]→[MODE]screenintheon-screenmenuandselect[PIP]or[PICTUREBYPICTURE].

14


Case 2. Using four projectors (resolution: FULL HD) to project videos with a resolution of 3840 × 2160 pixels [TILING]Connection example and projection image

On-screen menu operations1 Foursimilarvideosaredisplayedwhenfourprojectorsareprojected.

Pleaserequestthedealertoadjusttheprojectionpositionofeachprojector.

15


2 Operatetheon-screenmenuusingthefourrespectiveprojectorstodividetheimageintofourportions.

Display[DISPLAY]→[MULTISCREEN]→[PICTURESETTING]Screenintheon-screenmenuandselect[TIL-ING].

(1)Inthescreenforsettingthenumberofhorizontalunits,select[2UNITS].(numberofunitsinthehorizontaldirec-tion)

(2)Inthescreenforsettingthenumberofverticalunits,select[2UNITS].(numberofunitsintheverticaldirec-tion)

(3)Inthescreenforsettingthehorizontalorder,select[1stUNIT]or[2ndUNIT].

(lookatthescreens,theoneontheleftisthe[1stUNIT]whiletheoneontherightisthe[2ndUNIT])

(4)Inthescreenforsettingtheverticalorder,selectthe[1stUNIT]orthe[2ndUNIT].

(lookatthescreens,theoneatthetopisthe[1stUNIT]whiletheoneatthebottomisthe[2ndUNIT])

3 Adjustthelensshiftofeachprojectortofine-tunetheboundariesofthescreen.

Forfurtherfine-tuning,adjustusing[DISPLAY]→[EDGEBLENDING]intheon-screenmenuforeachprojector.

Fordetails,pleaserefertoUser'sManual“4-3DisplayingaPictureUsing[EDGEBLENDING]”.

16


Things to note when installing projectors• Leave60cm/23.6"oroverspacebetweentheprojectorswhenprojectorsareinstalledsidebyside,sothattheintakeventsoftheprojectorsarenotobstructed.Inaddition,leaveaspaceofatleast30cm/11.8"betweentheintakeventandthewallandatleast70cm/27.6"betweentheexhaustventandthewall.Whentheairintakeanddischarge outlet are obstructed, the temperature inside the projector will rise and this may result in a malfunction.

60cm/23.6"orgreater

• Donotdirectlystackprojectorunits.

WARNINGProjectors stacked directly could fall and cause injury. The projector(s) could also become damaged or broken.

• Exampleofmultipleprojectorsinstalledtogether Whenusingmultipleprojectorstogetherformultiscreenprojection,besuretosetthemupinaspecializedprojector

cabinet like the one that follows.[Installationexample]

IntakeventIntakevent Cabinet

Airdischarge

Airintake

Rear Rear

WARNING

Please request the dealer for special installation services such as when mounting the projector to the ceiling. Never carry out the installation by yourself. The projector may fall down and result in injury. Please use a sturdy cabinet that can withstand the weight of the projector for the installation. Please do not pile up the projectors directly on top of one another.

NOTE:• Fortherangeoftheprojectiondistance,pleasereferto“Throwdistanceandscreensize”.(→page5)

17


2-3. Connecting the Power Cord

Connectthesuppliedpowercordtotheprojector.

Firstconnectthesuppliedpowercord’sthree-pinplugtotheACINterminaloftheprojector,andthenconnecttheotherplugofthesuppliedpowercordinthewalloutlet.

WARNING:TOPREVENTFIREORSHOCK,DONOTEXPOSETHISUNITTORAINORMOISTURE.DONOTUSETHISUNIT’SPLUGWITHANEXTENSIONCORDORINANOUTLETUNLESSALLTHEPRONGSCANBEFULLYINSERTED.

ImportantInformation:

• Whenplugginginorunpluggingthesuppliedpowercord,makesurethatthemainpowerswitchispushedtotheoff[O]position.Failuretodosomaycausedamagetotheprojector.

• Donotuseathree-phasepowersupply.Doingsomaycausemalfunction.

MakesurethattheprongsarefullyinsertedintoboththeACINterminalandthewalloutlet.

Towalloutlet

Thisprojector'selectricalstandardisasfollows:

AC Power voltage AC200V-240VSinglephase50/60Hz

Standardinputcurrent 9.2A

Do not use this projector out of the standard range

CAUTION:PartsoftheprojectormaybecometemporarilyheatediftheprojectoristurnedoffwiththePOWERbuttonoriftheAC power supply is disconnected during normal projector operation.Usecautionwhenpickinguptheprojector.

18


Using the Power Cord Fixing MetalTopreventthepowercordfromaccidentlyremovingfromtheACINoftheprojector,attachthepowercordfixingmetal.

CAUTION• Topreventthepowercordfromcomingloose,makesurethatalltheprongsofthepowercordarefullyinsertedintotheACINterminaloftheprojectorbeforeusingthepowercordfixingmetal.Aloosecontactofthepowercordmaycauseafireorelectricshock.

Attaching the power cord fixing metal1. PinchandpulloutthepowercordfixingmetalflapthatishousedovertheACINterminal.

PowerCordFixingMetal

2. Pulldownthefixingmetalflapoverthepowercodeuntilthefixingmetalfitsintothebottomstopper.

Upperstopper

Bottomstopper

Forreleasingthefixingmetalflap,pullitupuntilthefixingmetalfitsintotheupperstopper.

19


2-4. Mounting the Lens Unit

MODEL Magnification

NP-9LS08ZM1 0.90-1.35

NP-9LS12ZM1 1.27-1.82

NP-9LS13ZM1 1.41-1.82

NP-9LS16ZM1 1.71-2.87

NP-9LS20ZM1 2.25-4.18

NP-9LS40ZM1 4.31-6.77

NOTE:• TheotherNECoptionallensesarenotavailableonthismodel.• Theprojectorandlensesaremadeofprecisionparts.Donotsubjectthemtoshockorexcessiveforces.• Removethelensunitwhenmovingtheprojector.Ifnot,thelenscouldbesubjecttoshockwhiletheprojectorisbeingmoved,damagingthelensandthelensshiftmechanism.

• Whenremovingorinstallingthelensunit,returnthepositionofthelenstothecenterbeforeturningoffthepowertotheprojec-tor.

• Wheninstallingorremovingthelensunit,firstconfirmthatthemainpowerswitchtotheprojectorisoff,andthendisconnecttheACpowersupply.AftertheACpowersupplyhasbeendisconnected,allowtheprojectortosufficientlycoolbeforestartingthiswork.- Nevertouchthelenssurfacewhiletheprojectorisoperating.- Beverycarefulnottoletdirt,grease,etc.,onthelenssurfaceandnottoscratchthelenssurface.- Performtheseoperationsonaflatsurfaceoverapieceofcloth,etc.,topreventthelensfromgettingscratched.- Whenleavingthelensofftheprojectorforlongperiodsoftime,mountDust-proofcushionontheprojectortopreventdustordirtfromgettinginside.

• Neverturnonthelightsourcewithoutmountingthelens.Itmaycauseofseriousdamagetoyoureyesbystronglight.

SinceNP-PH1202HLisalaserprojector,wedonotreleasetheproceduretomountanoptionallens,i.e.,mountandadjustmentofanoptionallensmustbeperformedbyaqualifiedtechnician.NP-9LS08ZM1isusedintheexplanationForother lensunits,pleasetakesameprocedurestomount,however,thelenshoodisequippedonNP-9LS08ZM1exclusively,theproceduretomounting/removingthelenshoodisnotrequired for others. At the same time, the image adjustment mechanism by manual besides the focus adjustment is alsoequippedonNP-9LS08ZM1.

20


Lens unit mounting methodPreparation:Removingthelenscover(→ see page 9)

NOTE:• Oncethelenscoversareremoved,itwillactivatetheprotectioncircuit.Aftermountingthelens,securelyinstallthelenscover.

*NP-9LS08ZM1isusedontheexplanatoryillustration.

1.Removethefrontandrearlenscapsonthelensunit:

NOTE:• Payenoughattentionnottotouchthelenssurface,itmaybecauseofsoilandscratchdamage.

Frontlenscap

RearlenscapConnectingposition(threepositions)

2. Mount the lens unit onto the projector.

①Alight theconnectingpositionsof the lensunit to theprojector connector socket and insert the lens unitstraight.

②Turntheoptionallensclockwiseuntilclicksoundisheard,theoptionallensismountedontheprojectorsecurely.

Lenshood

3. Removethelenshood.(ForNP-9LS08ZM1only)

①Removethelenshoodfixingscrewbya2.5mmhexagonheadeddriver.

②Turn the lens hood and remove it from the optionallens.

LenshoodLenshoodfixingscrew

Conditionwithoutthelenshood

21


4. Install the lens cover onto the projector.

NOTE:• IfNP-9LS08ZM1isusedonyourprojector,payenoughattentionsincethelensisexposed.

• Ifthecoverisnotinstalledproperly,errorwillbeissued.Securelyset5clawsintothepositionontheprojector.

Lenscover

5. Mountthelenshood.(ForNP-9LS08ZM1only)

NOTE:• Makesuretomountthelenshoodforprotectingthelens. Turnthelenshoodformountingandfastenitbythefixingscrew.

Lenshood

6. Lock the lens cover using the service key.

Lens unit removal method

NOTE:• Powerofftheprojectorandpulloutthepowerplugfromthewalloutlet.

• Waitforacertaintimetocompletelycooldowntheprojectorandthenremovethelenscover.

Perform the mounting procedures reversely for removing the lens unit.

• Forremovingthelensunitfromtheprojector,pressdownand hold the release lever, turn the lens unit counter-clockwise by its turn end and then slowly pull the unit out straight.

Releaselever

22


2-5. Mounting the Optional Board (sold separately)CAUTIONBeforemountingorremovingtheoptionalboard,besuretoturnofftheprojector,waitforthefanstostopandturnoff the main power switch.

Toolneeded:Phillipsscrewdriver(plus-head)

1. Turnoffthemainpowerswitchoftheprojector.

2. LoosenthetwoscrewsontheSLOTcoveroftheterminals.

RemovethetwoscrewsandtheSLOTcover.

NOTE:Keepthetwoscrewsandtheslotcover.

3. Inserttheoptionalboardintotheslot.

Makesurethattheboardisinsertedintotheslotinthecorrectorientation.

Incorrectorientationmaycausemiscommunicationbetweentheoptionalboardandprojector.

23


4. Tightenthetwoscrewsonbothsidesoftheslot.

• Besuretotightenthescrews.

Thiswillcompleteinstallationoftheoptionalboard.

Toselecttheoptionalboardsource,selectSLOTastheinput.

NOTE:• Mountingtheoptionalboardmaycausethefanstoruninthestandbymodeforthepurposeofcoolingdependingontheoptionalboard.Thefanspeedmayalsoincreaseinordertocooltheprojectorproperly.Bothoftheseinstancesareconsiderednormalandnotamalfunctionoftheprojector.

24

3. Projector Adjustment and Connecting3-1. Flow of Adjustment and ConnectingPerform the adjustment and connection of the projector according to the the following procedure

Step 1• TurningontheProjector(→ page 25)

Step 2 • Selectingtheprojectororientation(→ page 28)

Step 3 • AdjustingthePictureSizeandPosition(→ page 29)

Displaythetestpatterntoadjustthescreensize,screenratioandfocus.

Step 4• ConnectingtoOtherEquipments(→ page 35)

Step 5• OptimizingComputerSignalAutomatically(→ page 46)

ThischapterexplainstheadjustmentandconnectionoftheprojectorwithStepsfrom1to5.The adjustment and connection of the projector is completed by performing all steps in order

25

3. Projector Adjustment and Connecting

3-2. Turning on the ProjectorNOTE:• Theprojectorhastwopowerswitches:AmainpowerswitchandaPOWERbutton(POWERONandOFFontheremotecontrol)• Turning on the projector:1. PressthemainpowerswitchtotheONposition(I).

Theprojectorwillgointostandbymode.

2. PressthePOWERbutton.

Theprojectorwillbecomereadytouse.

• Turning off the projector:1. PressthePOWERbutton.

Theconfirmationmessagewillbedisplayed.

2. PressthePOWERbuttonagain.

Theprojectorwillgointostandbymode.

3. PressthemainpowerswitchtotheOFFposition(O).

Theprojectorwillbeturnedoff.

1. PressthemainpowerswitchtotheONposition(I).

ThePOWERindicatorlightsupred.*

* ThisindicatesthattheSTANDBYmodeisin[NORMAL]setting.

• Thebuzzersound is releasedwhen [NOTIFICATIONSETTING]for[BUZZER]isON.

WARNING

Theprojector producesa strong light.When turningonthe power, make sure no one within projection range is looking at the lens.

NOTE:• The[STANDBYMODE]settingwillbedisabledandtheprojectorwillgointothesleepmodewhenthenetworkserviceisutilizedortheprojectorreceivesHDBaseTsignal.Inthesleepmode,thefansintheprojectorsometimesrotateforthepurposeofinteriorpartsprotection.

26


2. Press the (POWER)buttonontheprojectorcabinetorthePOWERONbuttonontheremotecontrol.

The POWER indicator goes from a steady red light toaflashingblue light,and thepicture isprojectedon thescreen.

• Ifusingtheremotecontrol,pressthePOWERONbut-ton.

• Whenthereisnosignaltheunitwillprojectabluescreen(factorydefaultmenusettings).

• Ifthepictureisblurry,adjustthescreenfocus.(→ page 33)

• Whenitisdarkpressthe (lights)button.TheindicatorpanelbacklightandtheLEDlampontherightsideoftheprojectorwillturnon.

TIP:• TheunithasaPowerOnShutterfunctionthatallowsthelightsourcetoturnoffevenwhenconnectedtoapowersource.(→page49)

• PressingthebuttonwillnotactivatetheunitwhentheKEYLOCKindicatorisflashingorange.(→page61)

• Whenthemessage“PROJECTORISLOCKED!ENTERYOURPASSWORD.” is displayed, itmeans that the [SECURITY]featureisturnedon.

Afteryouturnonyourprojector,ensurethatthecomputerorvideosourceisturnedon.

NOTE:Thebluescreen([BLUE]background)isdisplayedwhennosignalisbeinginput(byfactorydefaultmenusettings).

Standby Blinking Power On

Steady red light Blinking blue light

Steady blue light

Performing Lens Calibration • After installing or replacing the lens unit (below *) soldseparately,presstheLENSCALIBRATIONbuttonontheprojector, or hold down the CTL button on the remote control thenpresstheINFO/L-CALIB.buttontocarryout [LENSCALIBRATION]. By carrying out [LENSCALIBRATION], the adjustmentrangeof thezoomandfocusof the[LENSMEMORY] iscalibrated.

If you need to install or replace the lens unit, contact your dealer and have them do it for you.

27


Note on Startup screen (Menu Language Select screen)Whenyoufirstturnontheprojector,youwillgettheStartupmenu.Thismenugivesyoutheopportunitytoselectoneofthe29menulanguages.

To select a menu language, follow these steps:

1. Use the , , or buttontoselectoneofthe29languagesfromthemenu.

2. PresstheENTERbuttontoexecutetheselection.

After this has been done, you can proceed to the menu operation.If you want, you can select the menu language later.(→[LANGUAGE]onpage49)

NOTE:• WhentheKEYLOCKindicatorisflashing,thatmeans[CONTROLPANELLOCK]hasbeensetandpressingthe buttonwillnotcausetheunittopower-on.Release[CONTROLPANELLOCK].(→page62)

• WhilethePOWERindicatorisblinkingblueinshortcycles,thepowercannotbeturnedoffbyusingthepowerbutton.(WhilethePOWERindicatorisblinkingblueinlongcycles,theOFFTIMERisfunctionedandthepowercanbeturnedoff.)

28


3-3. Selecting the projector orientation

Selecting Projector Orientation [ORIENTATION]Thisreorientsyourimageforyourtypeofprojection.Theoptionsare:desktopfrontprojection,ceilingrearprojection,desktop rear projection, and ceiling front projection.

NOTE:• Pleaseconsultthedealerifyourequirespecialinstallationservicese.g.whenmountingtheprojectortoaceiling.Neverinstalltheprojectoronyourown.Thismayresultintheprojectorfallingdownandcausinginjurytopeople.

DESKTOPFRONT CEILINGREAR

DESKTOPREAR CEILINGFRONT

29


3-4. Adjusting the Picture Size and PositionUsethelensshiftdial,theleveladjusterlever,thezoomlever/zoomringandthefocusringtoadjustthepicturesizeand position.Inthischapterdrawingsandcablesareomittedforclarity.

Adjusting the projector’s settings[Leveladjuster](→ page 30)

Adjustingtheprojectedimage’sverticalandhorizontalposition[Lensshift](→ page 31)

Adjusting the focus[Focus](→ page 33)

Finelyadjustingthesizeofanimage[Zoom](→ page 33)

TIP:• Built-intestpatternscanbeconvenientlyusedforadjustingthepicturesizeandposition.(→page47) ApressoftheTESTbuttonwilldisplaythetestpattern.Theorbuttoncanselectonetestpattern.Toclosethetestpattern,changethesourcetoanother.

30


CAUTION• Performtheadjustmentfrombehindorfromthesideoftheprojector.Adjustingfromthefrontcouldexpose

your eyes to strong light which could injure them.

• Keephandsawayfromthelensmountingportionwhilethelensshiftisinoperation.

Failure to do so could result in hands being pinched by the moving lens.

Adjustment of the projector’s settings (Level adjusters)The projector must be placed square to the screen otherwise keystone distortion may appear on the screen. For set-tingtheprojectorperpendiculartothescreenwhenviewedfromtheside,utilizingtheleveladjustersequippedateachcorneroftheprojectorbottom.MaximumAdjustablelengthoftheleveladjusteris10mm/0.39".

Example for adjustment

Raise Raise

Lower Lower

Leveladjuster

NOTE:• Donotlengtheneachoftheleveladjustersanymorethan10mm/0.39".Theforceofdoingsomaycausetheleveladjustertocomeoff,resultingindamagetotheprojector.

• Payattentiontolengthenorshortentwoleveladjustersatfrontatthesametime.Samefortherearadjusters,otherwise,theweightoftheprojectorisloadedononeleveladjusteranditmaycauseofdamagetoit.

31


Adjusting the projected image's vertical and horizontal position (Lens shift)

NOTE:• Shiftingthelenstothemaximumintwodirectionscombinedwillcausetheedgesoftheimagetobecomedarkorwillcausesomeshadows.

Adjusting with buttons on the cabinet1. PresstheLENSSHIFT/HOMEPOSITIONbutton.

The[LENSSHIFT]screenwillbedisplayed.

2. Press the or button.

Usethebuttonstomovetheprojectedimage.

• Returningthelensshiftpositiontothehomeposition

PressandholdtheLENSSHIFT/HOMEPOSITIONbuttonfor2secondstoreturnthelensshiftpositiontothehomeposition(nearlycenterposition)

32


Adjusting with the remote control1. HoldtheCTLbuttonandpresstheECO/L-SHIFTbutton.

The[LENSSHIFT]screenwillbedisplayed.

2. Press the or button.

Usethebuttonstomovetheprojectedimage.

TIP:• Thefigurebelowshowsthelensshiftranges(projectionmode:desktop/front)oflensunitsNP-9LS08ZM1,NP-9LS12ZM1,NP-9LS13ZM1,NP-9LS16ZM1,andNP-9LS20ZM1.ForNP-9LS40ZM1checkpage7.

100%V

50%V20%V 20%V

20%V20%V50%V

100%H

11%H 11%H

11%H11%H



Descriptionofsymbols:Vindicatesvertical(heightoftheprojectedimage),Hindicateshorizontal(widthoftheprojectedim-age).

33


Focus

NOTE:• ForlensunitNP-9LS08ZM1,bothcentralandperipheralfocusmustbeadjusted.UsetheFOCUS+/−buttonstoadjustthecentralfocus.

1. PresstheFOCUS+/−button.

• Ontheremotecontrol,whilepressingontheCTLbutton,pressonVOL/FOCUS(+)or(−)button.

Thefocusisadjusted.

TIP:Toobtainthebestfocus,performthefollowing(forfixedinstallation)Preparation:Warmuptheprojectorforonehour.1.UsetheFOCUS+/−buttonstomakesureyouobtainthebestfocus.Ifyoudonot,movetheprojectorbackandforth.2.Selectthe[TESTPATTERN]fromthemenuanddisplaythetestpattern.(→page47)• YoucanalsousetheTESTbuttonontheremotecontroltodisplaythetestpattern.

3.KeeppressingtheFOCUS−buttonuntilthegridofthetextpatternismadeinvisible.4.KeeppressingtheFOCUS+buttonuntilyouobtainthebestfocus. Ifyouadjustbeyondthebestfocalpoint,gobacktostep3andrepeattheprocedures.

NP-9LS08ZM1 Focus adjustment of the lens unitTheNP-9LS08ZM1unitadjuststhefocusaroundandonthecenterofthescreen.

NOTE:Theimageplaneadjustmentmechanismislockedwithscrewswhenshippedfromthefactory.Theimageplaneadjustmentmechanismisnotusednormally.Useitwhenthelevelcannotbesatisfiedwithjustthefocusadjust-ment.

Adjustment method1 PresstheFOCUS+/–buttontoadjustthefocusonthecenterofthe

screen.

PresstheVOL./FOCUS+/–buttonwhilepressingdowntheCTLbuttonwhenoperatingwiththeremotecontrol.

34


2 Loosenthescrewsontheimageplaneadjustmentmechanism.

Peripheralfocusring

Imageplaneadjustmentmechanismscrew

3 Adjustthefocusaroundthescreenbymanuallyturningtheperipheralfocusringtotheleftorright.

4 Tighten thescrewson the imageplaneadjustmentmechanismtosecure the unit.

Thefocusonthecenterofthescreendoesnotchangeverymuchevenafteradjustingtheperipheralfocussothecenterfocusdoesnotneedtobere-adjusted.

Zoom1. PresstheZOOM+/−button.

• Ontheremotecontrol,whilepressingontheCTLbutton,presstheD-ZOOM/ZOOM(+)or(−)button.

Thezoomisadjusted.

35


3-5. Connecting to Other Equipments3-5-1. Connecting a computerAcomputercable,BNCcable(5-coretype),HDMIcable,oraDisplayPortcablecanbeusedtoconnecttoacom-puter.The connection cable is not enclosed with the projector. Please get ready a suitable cable for the connection.

Analog RGB signal connection

• Connectthecomputercabletothedisplayoutputterminal(miniD-sub15pin)onthecomputerandtheCOMPUTERIN terminal on the projector. Please use a computer cable attached with a ferrite core.

• Whenconnectingthedisplayoutputterminal(miniD-sub15pin)onthecomputertotheBNCinputterminal,useaconversioncabletoconverttheBNCcable(5core)toaminiD-sub15pincable.

• Selectthesourcenameforitsappropriateinputterminalafterturningontheprojector.

Input terminalSOURCEbuttonontheprojector

cabinetButtonontheremotecontrol

COMPUTERIN COMPUTER COMPUTER1

BNC BNC COMPUTER2

COMPUTER IN

BNC IN

Computercable(soldcommercially)

RGB-to-BNCcable(notsupplied)

NOTE:Pleasechecktheoperatingmanualofthecom-puterasthename,positionanddirectionoftheterminalmaydifferdependingonthecomputer.

36


Digital RGB signal connection

• ConnectacommerciallyavailableHDMIcablebetweenthecomputer’sHDMIoutputterminalandtheprojector’sHDMI IN terminal.

• ConnectacommerciallyavailableDisplayPortcablebetweenthecomputer’sDisplayPortoutputterminalandtheprojector’s DisplayPort IN terminal.




HDMI IN HDMI HDMI

DisplayPort IN DisplayPort DisplayPort

DisplayPort INHDMI IN

HDMIcable(notsupplied) DisplayPortcable(notsupplied)

37


Cautions when connecting an HDMI cable• UseacertifiedHighSpeedHDMI®CableorHighSpeedHDMI®CablewithEthernet.

Cautions when connecting a DisplayPort cable• UseacertifiedDisplayPortcable.

• Dependingonthecomputer,sometimemayberequireduntiltheimageisdisplayed.

• SomeDisplayPortcables(commerciallyavailable)havelocks.

• Todisconnectthecable,pressthebuttononthetopofthecable’sterminal,thenpullthecableout.

• PowercanbesuppliedtotheconnectingdevicefromtheDisplayPortINterminal(maximumof1.65W).However,power will not be supplied to the computer.

• WhensignalsfromadevicethatusesasignalconverteradapterareconnectedtotheDisplayPortINterminal,insome cases the image may not be displayed.

• WhentheHDMIoutputofacomputerisconnectedtotheDisplayPortINterminal,useaconverter(commerciallyavailable).

38


Cautions when using a DVI signal• WhenthecomputerhasaDVIoutputterminal,useacommerciallyavailableconvertercabletoconnectthecom-

puter to the projector’s HDMI IN terminal (only digital video signals can be input).

HDMI IN

NOTE:WhenViewingaDVIDigitalSignal• Turnoffthepowerofthecomputerandprojectorbeforeconnectingdevices.• Whenavideodeckisconnectedviaascanconverter,etc.,thedisplaymaynotbecorrectduringfast-forwardingandrewind-ing.

• UseaDVI-to-HDMIcablecompliantwithDDWG(DigitalDisplayWorkingGroup)DVI(DigitalVisualInterface)revision1.0stan-dard.Thecableshouldbewithin197"/5mlong.

• TurnofftheprojectorandthePCbeforeconnectingtheDVI-to-HDMIcable.• ToprojectaDVIdigitalsignal:Connectthecables,turntheprojectoron,thenselecttheHDMI.Finally,turnonyourPC. Failuretodosomaynotactivatethedigitaloutputofthegraphicscardresultinginnopicturebeingdisplayed.Shouldthishappen,restartyourPC.

• SomegraphicscardshavebothanalogRGB(15-pinD-Sub)andDVI(orDFP)outputs.Useofthe15-pinD-Subterminalmayresultinnopicturebeingdisplayedfromthedigitaloutputofthegraphicscard.

• DonotdisconnecttheDVI-to-HDMIcablewhiletheprojector isrunning.If thesignalcablehasbeendisconnectedandthenreconnected,animagemaynotbecorrectlydisplayed.Shouldthishappen,restartyourPC.

• TheCOMPUTER IN terminal supportsWindowsPlugandPlay.TheBNC input terminalsdonotsupportWindowsPlugandPlay.

• AMacsignaladapter(commerciallyavailable)mayberequiredtoconnectaMaccomputer. ToconnectaMaccomputerequippedwithaMiniDisplayPorttotheprojector,useacommerciallyavailableMiniDisplayPort→DisplayPortconvertercable.

39


HDMI IN

HDMI OUT HDMI IN

3-5-2. Connecting an External Monitor

Asshowninthefigure,whentheprojectorisconnectedtoacomputer,thesamecontentfromtheHDMIinputsignalisdisplayedonthemonitorforconfirmation.• TheHDMIOUTterminalcannotsendanalogsignals(COMPUTERINterminal,BNCterminal).

NOTE:• WhenoutputtingHDMIsignals,turnonthepowerofthevideodeviceontheoutputsideandkeepitconnectedbeforeinputtingvideosignalsintothisdevice.TheHDMIOUTterminalsoftheprojectorareequippedwithrepeaterfunctions.WhenadeviceisconnectedtotheHDMIOUTterminal,theresolutionoftheoutputsignalislimitedbytheresolutionsupportedbytheconnecteddevice.

• InthecaseoftheHDMIOUTterminaloftheprojector,thetheoreticalnumberofunitsthatcanbeconnectedinaseriesisseven.Themaximumnumberofunitsthatcanbeconnectedmaybereducedbytheexternalenvironmentandqualityofthesignalandcable,etc.ThenumberofunitsthatcanbeconnectedmaydifferdependingontheHDCPversion,restrictiononthenumberofHDCPrepeatersinthesourcedeviceandthequalityofthecable.Theoverallsystemneedstobecheckedinadvancewhenbuild-ingasystem.

• Whenthe[STANDBYMODE]issetto[NORMAL],videowillnotbeoutputiftheprojectorgoesintothestandbymode.Setthemodeto[HDBaseTSTANDBY],turnonthepowerofthetransmissiondeviceandkeepitinaconnectedstate.

• Whenthe[STANDBYMODE]ofthisdeviceissetto[NORMAL],HDMIsignalswillnotbeoutput.TooutputHDMIsignals,setthe[STANDBYMODE]to[HDBaseTSTANDBY],turnonthepowersupplyofthetransmissiondeviceandkeepitconnected.

• HDMIrepeaterfunctionwillnotbefunctionedifswitchingterminalsandputtingin/pullingouttheHDMIcableisperformedonthe2ndprojectorandafter.

HDMIcable(notsupplied) HDMIcable(notsupplied)

40


3-5-3. Connecting Your Blu-ray Player or Other AV Equipment

Composite video signal/S-video signal connection




BNC(CV) BNC(CV) VIDEO

BNC(Y/C) BNC(Y/C) S-VIDEO

CV Y C

BNC（CV）BNC（Y） BNC（C）

IfthesignalisacompositevideosignalBNCcable(notsupplied)

IfthesignalisanS-videosignalBNCcable(notsupplied)

Audioequipment

41


Component signal connectionConnecttheBlu-rayplayer’saudiototheaudiodevice.





BNC BNC COMPUTER2

NOTE:• Whenthesignalformatissetto[AUTO](defaultfactorysettingwhenshipped),thecomputersignalandcomponentsignalareautomatically distinguished and switched. If the signals cannot bedistinguished, select [COMPONENT]under [ADJUST]→[VIDEO]→[SIGNALTYPE]intheon-screenmenuoftheprojector.

• ToconnecttoavideodevicewithaDterminal,usethesoldseparatelyDterminalconverteradapter(modelADP-DT1E).

COMPUTER IN

Cr CbY

15-pin-to-RCA(female)×3cableadapter(ADP-CV1E) BNC(male)-to-RCA(male)conversion

cable×3(soldcommercially)

ComponentvideoRCA×3cable(notsup-plied)

Blu-rayplayer

Audioequipment

42


HDMI signal connectionYoucanconnecttheHDMIoutputofyourBlu-rayplayer,harddiskplayer,ornotebooktypePCtotheHDMIINterminalof your projector.



HDMI IN HDMI HDMI

TIP:ForusersofaudiovideoequipmentwithanHDMIterminal:Select“Enhanced”ratherthan“Normal”ifHDMIoutputisswitchablebetween“Enhanced”and“Normal”.Thiswillprovideimprovedimagecontrastandmoredetaileddarkareas.Formoreinformationonsettings,refertotheinstructionmanualoftheaudiovideoequipmenttobeconnected.

• WhenconnectingtheHDMIINterminaloftheprojectortotheBlu-rayplayer,theprojector’svideolevelcanbemadesettingsinaccordancewiththeBlu-rayplayer’svideolevel.Inthemenuselect[ADJUST]→[VIDEO]→ [VIDEOLEVEL]andmakenecessarysettings.

HDMI IN

Audiocable(notsupplied)

HDMIcable(notsupplied)UseHighSpeedHDMI®Cable.

43


3-5-4. Connecting a document cameraYoucanconnectadocumentcameraandprojectprinteddocuments,etc.





BNC(CV) BNC(CV) VIDEO

BNC (CV)

COMPUTER IN

VIDEO

NOTE:• Name,position,anddirectionofterminalsarevarydependingoncameramodel.Pleasecheckuser’smanualofyourcamerafordetails.

BNC(male)andRCA(male)conver-sioncable(notsupplied)

Computercable(notsupplied)

44


3-5-5. Connecting to a Wired LANTheprojectorcomesstandardwithaEthernet/HDBaseTport(RJ-45)whichprovidesaLANconnectionusingaLANcable. TouseaLANconnection,youarerequiredtosettheLANontheprojectormenu.Select[SETUP]→[NETWORKSETTINGS]→[WIREDLAN].(→User'smanual:page115).

Example of LAN connectionExampleofwiredLANconnection

Ethernet/HDBaseT

Server

Hub

LANcable(notsupplied)

NOTE: Use a Category 5 or higher LANcable.

45


3-5-6. Connecting to a HDBaseT transmission device (sold commercially)HDBaseTisaconnectionstandardforhomeappliancesthatisestablishedbytheHDBaseTAlliance.UseaLANcablesoldcommerciallytoconnecttheEthernet/HDBaseTportoftheprojector(RJ-45)toaHDBaseTtransmission device sold commercially.TheEthernet/HDBaseTportoftheprojectorsupportsHDMIsignals(HDCP)fromtransmissiondevices,controlsignalsfrom external devices (serial, LAN) and remote control signals (IR commands).

Connection example

Ethernet/HDBaseT

Computer(forcontroluse)Computer(foroutputuse)

Exampleofatransmissiondevice

Remotecontrol

HDMIoutputvideodevice

NOTE:• NeverusetheLANport(RJ-45)ontheprojectorterminalpanelforconnectingaHDBaseTtransmissiondevice.Itmaycauseofmalfunction.

• Pleaseuseashieldedtwistedpair(STP)cableofCategory5eorhigherfortheLANcable(soldcommercially).• ThemaximumtransmissiondistanceovertheLANcableis100m.(themaximumdistanceis70mfora4Ksignal)• Pleasedonotuseothertransmissionequipmentbetweentheprojectorandtransmissionequipment.Thepicturequalitymaybedeterioratedasaresult.

• ThisprojectorisnotguaranteedtoworkwithallHDBaseTtransmissiondevicessoldcommercially.

46


3-6. Optimizing Computer Signal AutomaticallyAdjusting the Image Using Auto AdjustWhenanimagefromHDMIIN,DisplayPortIN,BNCinputterminal(analogRGB),COMPUTERIN,orHDBaseTisbeingprojected,andtheedgeiscutoffortheimagequalityispoor,thisbuttoncanbeusedtoautomaticallyoptimizethe projection image on the screen.

Press theAUTOADJ.button tooptimizeacomputer imageautomati-cally.This adjustment may be necessary when you connect your computer forthefirsttime.

[Poorpicture] [Normalpicture]

NOTE:Somesignalsmaytaketimetodisplayormaynotbedisplayedcorrectly.

47

* The asterisk (*) indicates that the default setting varies depending on the signal.*1 The[GAMMACORRECTION]itemisavailablewhenanitemotherthan[DICOMSIM.]isselectedfor[REFERENCE].*2 The[SCREENSIZE]itemisavailablewhen[DICOMSIM.]isselectedfor[REFERENCE].*3 When[PRESENTATION]or[HIGH-BRIGHT]isselectedin[REFERENCE],the[COLORTEMPERATURE]isnotavailable.

•Basicmenuitemsareindicatedbyshadedarea.

4. List of Menu ItemsThis chapter explains the list of on-screen menu items for the projector. Please refer to the user's manual about func-tions and operation on each menu.Somemenuitemsarenotavailabledependingontheinputsource.

Menu Item Default Options

INPUT

HDMI *DisplayPort *BNC *BNC(CV) *BNC(Y/C) *COMPUTER *HDBaseTSLOTENTRY LISTTEST PATTERN

ADJUST

PICTURE

MODE STANDARD STANDARD, PROFESSIONAL

PRESET * HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE, GRAPHIC, sRGB, DICOM SIM.

DETAIL SETTINGS

GENERAL

REFERENCE * HIGH-BRIGHT, PRESENTATION, VIDEO, MOVIE, GRAPHIC, sRGB, DICOM SIM.

GAMMA CORRECTION*1 SELECT DYNAMIC, NATURAL, BLACK DETAILNATURAL SETTING

SCREEN SIZE*2 * LARGE, MEDIUM, SMALLCOLOR TEMPERATURE*3 *DYNAMIC CONTRAST * OFF, MOTION IMAGE, STILL IMAGE

WHITE BALANCECONTRAST R 0CONTRAST G 0CONTRAST B 0BRIGHTNESS R 0BRIGHTNESS G 0BRIGHTNESS B 0

COLOR CORRECTIONRED 0GREEN 0BLUE 0YELLOW 0MAGENTA 0CYAN 0

CONTRAST 50BRIGHTNESS 50SHARPNESS 10COLOR 50HUE 0RESET

IMAGE OPTIONS

CLOCK *PHASE *HORIZONTAL *VERTICAL *BLANKING * TOP, BOTTOM, LEFT, RIGHTOVERSCAN AUTO AUTO, 0[%], 5[%], 10[%]

ASPECT RATIO

AUTO (COMPUTER) AUTO, 4:3, 5:4, 16:9, 15:9, 16:10, NATIVE

AUTO (COMPONENT/VIDEO/S-VIDEO) AUTO, 4:3, LETTERBOX, WIDE SCREEN, ZOOM

AUTO (COMPONENT/VIDEO/S-VIDEO) AUTO, 4:3 WINDOW, LETTERBOX, WIDE SCREEN, FULL

INPUT RESOLUTION * –

VIDEO

NOISE REDUCTIONRANDOM NR OFF OFF, LOW, MEDIUM, HIGHMOSQUITO NR OFF OFF, LOW, MEDIUM, HIGHBLOCK NR OFF OFF, LOW

DEINTERLACE NORMAL NORMAL, MOVIE, STILLCONTRAST ENHANCEMENT

MODE AUTO OFF, AUTO, NORMALGAIN

SIGNAL TYPE AUTO AUTO, RGB, COMPONENTVIDEO LEVEL AUTO AUTO, NORMAL, ENHANCED, SUPER WHITE

4. List of Menu Items

48


ADJUST

3D SETTINGS

STEREO VIEWER SINGLE, DUAL LEFT, DUAL RIGHT

FORMAT AUTOAUTO, OFF(2D), FRAME PACKING, SIDE BY SIDE(HALF), SIDE BY SIDE(FULL), TOP AND BOTTOM, FRAME ALTERNATIVE, LINE ALTERNATIVE

L/R INVERT OFF OFF, ON

LENS MEMORY

STOREMOVERESET

DISPLAY

PIP/PICTURE BY PICTURE

SUB INPUT OFF OFF, HDMI, DisplayPort, BNC, BNC(CV), BNC(Y/C), COMPUTER, HDBaseT, SLOT

MODE PIP PIP, PICTURE BY PICTUREPICTURE SWAP OFF OFF, ON

PIP SETTING

START POSITION TOP-LEFT TOP-LEFT, TOP-RIGHT, BOTTOM-LEFT, BOTTOM-RIGHTHORIZONTAL POSITIONVERTICAL POSITIONSIZE MEDIUM LARGE, MEDIUM, SMALL

BORDER

GEOMETRIC CORRECTION

KEYSTONE

HORIZONTALVERTICALTILTTHROW RATIO

CORNERSTONE TOP-LEFT, TOP-CENTER, TOP-RIGHT, CENTER-LEFT, CENTER-RIGHT, BOTTOM-LEFT, BOTTOM-CENTER, BOTTOM-RIGHT

HORIZONTAL CORNER TOP-LEFT, TOP-CENTER, TOP-RIGHT, CENTER-LEFT, CENTER-RIGHT, BOTTOM-LEFT, BOTTOM-CENTER, BOTTOM-RIGHT

VERTICAL CORNER TOP-LEFT, TOP-CENTER, TOP-RIGHT, CENTER-LEFT, CENTER-RIGHT, BOTTOM-LEFT, BOTTOM-CENTER, BOTTOM-RIGHT

PINCUSHION TOP, BOTTOM, LEFT, RIGHTPC TOOL OFF OFF, 1, 2, 3RESET

EDGE BLENDING

MODE OFF OFF, ON

TOP

CONTROL ON OFF, ONMARKER OFF OFF, ONRANGEPOSITION

BOTTOM


LEFT


RIGHT


BLACK LEVEL

TOP-LEFTTOP-CENTERTOP-RIGHTCENTER-LEFTCENTERCENTER-RIGHTBOTTOM-LEFTBOTTOM-CENTERBOTTOM-RIGHT

MULTI SCREEN

WHITE BALANCE

MODE OFF OFF, ONCONTRAST WCONTRAST RCONTRAST GCONTRAST BBRIGHTNESS WBRIGHTNESS RBRIGHTNESS GBRIGHTNESS B

PICTURE SETTING

MODE OFF OFF, ZOOM, TILING

ZOOM

HORIZONTAL ZOOMVERTICAL ZOOMHORIZONTAL POSITIONVERTICAL POSITION

TILING

WIDTH 1 UNIT, 2 UNITS, 3 UNITS, 4 UNITSHEIGHT 1 UNIT, 2 UNITS, 3 UNITS, 4 UNITSHORIZONTAL POSITION 1st UNIT, 2nd UNIT, 3rd UNIT, 4th UNITVERTICAL POSITION 1st UNIT, 2nd UNIT, 3rd UNIT, 4th UNIT


49


SETUP

MENU

LANGUAGE ENGLISH

ENGLISH, DEUTSCH, FRANÇAIS, ITALIANO, ESPAÑOL, SVENSKA, 日本語DANSK, PORTUGUÊS, ČEŠTINA, MAGYAR, POLSKI, NEDERLANDS, SUOMINORSK, TÜRKÇE, РУССКИЙ, , Ελληνικά, 中文, 한국어ROMÂNĂ, HRVATSKA, БЪЛГАРСКИ, INDONESIA, हिनदी, ไทย,

, 繁體中文COLOR SELECT COLOR COLOR, MONOCHROMEINPUT DISPLAY ON OFF, ONMESSAGE DISPLAY ON OFF, ONID DISPLAY ON OFF, ON3D CAUTION MESSAGE ON OFF, ON

DISPLAY TIME AUTO 45 SEC MANUAL, AUTO 5 SEC, AUTO 15 SEC, AUTO 45 SEC

FILTER MESSAGE OFF OFF, 100[H], 500[H], 1000[H], 2000[H], 5000[H], 10000[H], 20000[H]

INSTALLATION

ORIENTATION DESKTOP FRONT

DESKTOP FRONT, CEILING REAR, DESKTOP REAR, CEILING FRONT

SCREEN TYPE FREE FREE, 4:3 SCREEN, 16:9 SCREEN, 16:10 SCREEN

WALL COLOR OFFOFF, WHITEBOARD, BLACKBOARD, BLACKBOARD (GRAY), LIGHT YELLOW, LIGHT GREEN, LIGHT BLUE, SKY BLUE, LIGHT ROSE, PINK

FAN MODE AUTO AUTO, HIGH

LIGHT MODELIGHT MODE NORMAL NORMAL, ECO1, ECO2, LONG LIFECONSTANT BRIGHTNESS OFF OFF, ONADJUST 30–100%

SHUTTER SETTINGS

POWER ON SHUTTER OPEN OPEN, CLOSEPICTURE MUTE SHUTTER OPEN OPEN, CLOSEFADE IN TIME 0–10 SECFADE OUT TIME 0–10 SEC

REF. WHITE BALANCE

CONTRAST RCONTRAST GCONTRAST BBRIGHTNESS RBRIGHTNESS GBRIGHTNESS BUNIFORMITY RUNIFORMITY B

REF. LENS MEMORY

PROFILE 1 1, 2STOREMOVERESETLOAD BY SIGNAL OFF OFF, ONFORCED MUTE OFF OFF, ON

LENS CALIBRATION


50


SETUP CONTROL

TOOLS

ADMINISTRA-TOR MODE

MENU MODE ADVANCED ADVANCED, BASICNOT SAVE SETTING VALUES OFF OFF, ONNEW PASSWORDCONFIRM PASSWORD

PROGRAM TIMER

ENABLE OFF OFF, ON

SETTINGS

EDIT

ACTIVE OFF, ON

DAY SUN, MON, TUE, WED, THU, FRI, SAT, MON-FRI, MON-SAT, EVERY DAY

TIMEFUNCTION POWER, INPUT, LIGHT MODEADVANCED SETTINGSPOWER OFF, ON

INPUT HDMI, DisplayPort, BNC, BNC(CV), BNC(Y/C), COMPUTER, HDBaseT, SLOT

LIGHT MODE NORMAL, ECO1, ECO2REPEAT OFF, ON

DELETEUPDOWNBACK

DATE AND TIME SETTINGS

TIME ZONE SETTIMGS

GMT

-12:00, -11:30, -11:00, -10:30, -10:00, -09:30, -09:00, -08:30, -08:00, -07:30, -07:00, -06:30, -06:00, -05:30, -05:00, -04:30, -04:00, -03:30, -03:00, -02:30, -02:00, -01:30, -01:00, -00:30, 00:00, +00:30, +01:00, +01:30, +02:00, +02:30, +03:00, +03:30, +04:00, +04;30, +05:00, +05:30, +06:00, +06:30, +07:00, +07:30, +08:00, +08:30, +09:00, +09:30, +10:00, +10:30, +11:00, +11:30, +12:00, +12:30, +13:00

DATE AND TIME SETTINGS

DATE MM/DD/YYYYTIME HH:MMINTERNET TIME SERVER OFF, ON

IP ADDRESSUPDATE

SUMMER TIME SETTINGS

ENABLE OFF, ONMON(START) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12

DAY(START)FIRST WEEK, SECOND WEEK, THIRD WEEK, FOURTH WEEK, LAST WEEKSUN, MON, TUE, WED, THU, FRI, SAT

TIME(START)MON(EXIT) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12

DAY(EXIT)FIRST WEEK, SECOND WEEK, THIRD WEEK, FOURTH WEEK, LAST WEEKSUN, MON, TUE, WED, THU, FRI, SAT

TIME(EXIT)TIME DIFFERENCE +01:00, +00:30, -00:30, -01:00

MOUSE (Note) Cannot be used for this device.CONTROL PANEL LOCK OFF OFF, ON

NOTIFICATION SETTINGSREAR LED ON OFF, ONBUZZER ON OFF, ON

SECURITY OFF OFF, ONCOMMUNICATION SPEED 38400bps 4800bps, 9600bps, 19200bps, 38400bps, 115200bps

CONTROL IDCONTROL ID NUMBER 1 1–254CONTROL ID OFF OFF, ON

REMOTE SENSOR FRONT/BACK FRONT/BACK, FRONT, BACK, HDBaseT

LENS TYPE WITH SENSOR WITH SENSOR, WITHOUT SENSOR


51


SETUP

NETWORK SETTINGS

WIRED LAN

PROFILES DISABLE, PROFILE 1, PROFILE 2DHCP OFF, ONIP ADDRESS 192.168.0.10SUBNET MASK 255.255.255.0GATEWAY 192.168.0.1AUTO DNS OFF, ONDNS CONFIGURATIONRECONNECT

PROJECTOR NAME PROJECTOR NAME PH1202HL Series

DOMAINHOST NAME necpjDOMAIN NAME

ALERT MAIL

ALERT MAIL OFF, ONHOST NAMEDOMAIN NAMESENDER'S ADDRESSSMTP SERVER NAMERECIPIENT'S ADDRESS 1RECIPIENT'S ADDRESS 2RECIPIENT'S ADDRESS 3TEST MAIL

NETWORK SERVICE

HTTP SERVER

NEW PASSWORDCONFIRM PASSWORD

PJLinkNEW PASSWORDCONFIRM PASSWORD

AMX BEACON OFF, ON

CRESTRON

ROOMVIEW OFF, ONCRESTRON CONTROL (ENABLE, CONTROLLER IP ADDRESS, IP ID)

SOURCE OPTIONS

AUTO ADJUST NORMAL OFF, NORMAL, FINE

COLOR SYSTEMBNC(VIDEO) AUTO AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAMBNC(Y/C) AUTO AUTO, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM

DEFAULT INPUT SELECT LAST LAST, AUTO, HDMI, DisplayPort, BNC, BNC(CV), BNC(Y/C), COMPUTER, HDBaseT, SLOT

SEAMLESS SWITCHING OFF OFF, ON

CLOSED CAPTION OFF OFF, CAPTION1, CAPTION2, CAPTION3, CAPTION4, TEXT1, TEXT2, TEXT3, TEXT4

BACKGROUND BLUE BLUE, BLACK, LOGO

POWER OPTIONS

STANDBY MODE NORMAL NORMAL, HDBaseT STANDBYDIRECT POWER ON OFF OFF, ONAUTO POWER ON SELECT OFF OFF, HDMI, DisplayPort, COMPUTER, HDBaseT, SLOTAUTO POWER OFF 1:00 OFF, 0:05, 0:10, 0:15, 0:20, 0:30, 1:00OFF TIMER OFF OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00

SLOT POWERPROJECTOR ON ON OFF, ONPROJECTOR STANDBY ENABLE DISABLE, ENABLE

RESET

CURRENT SIGNALALL DATAALL DATA (INCLUDING ENTRY LIST)CLEAR FILTER HOURS


52


INFO.

USAGE TIMELIGHT HOURS USEDFILTER HOURS USEDTOTAL CARBON SAVINGS

SOURCE(1)

INPUT TERMINALRESOLUTIONHORIZONTAL FREQUENCYVERTICAL FREQUENCYSYNC TYPESYNC POLARITYSCAN TYPESOURCE NAMEENTRY NO.

SOURCE(2)

SIGNAL TYPEVIDEO TYPEBIT DEPTHVIDEO LEVELLINK RATELINK LANE3D FORMAT

SOURCE(3)

INPUT TERMINALRESOLUTIONHORIZONTAL FREQUENCYVERTICAL FREQUENCYSYNC TYPESYNC POLARITYSCAN TYPESOURCE NAMEENTRY NO.

SOURCE(4)

SIGNAL TYPEVIDEO TYPEBIT DEPTHVIDEO LEVELLINK RATELINK LANE3D FORMAT

WIRED LAN

IP ADDRESSSUBNET MASKGATEWAYMAC ADDRESS

VERSION(1)FIRMWAREDATASUB-CPU

VERSION(2) FIRMWARE3

OTHERS

DATE TIMEPROJECTOR NAMEMODEL NO.SERIAL NUMBERCONTROL ID (when [CONTROL ID] is set)

CONDITIONSINTAKE TEMPERATUREEXHAUST TEMPERATUREATMOSPHERIC PRESSURE

HDBaseT

SIGNAL QUALITYOPERATION MODELINK STATUSHDMI STATUS

53

5. MaintenanceThissectiondescribesthesimplemaintenanceproceduresyoushouldfollowtocleanthefilters,thelens,andthecabinet.

5-1. Cleaning the FiltersTheair-filterspongekeepsdustanddirtfromgettinginsidetheprojectorandshouldbefrequentlycleaned.Ifthefilteris dirty or clogged, your projector may overheat.

WARNING• Pleasedonotuseaspraycontainingflammablegastoremovedustattachedtothefilters,etc.Doingsomayresultinfires.

NOTE:Themessageforfiltercleaningwillbedisplayedforoneminuteaftertheprojectoristurnedonoroff.Whenthemessageisdisplayed,cleanthefilters.Thetimetocleanthefiltersissetto[OFF]attimeofshipment.(→page49)Tocancelthemessage,pressanybuttonontheprojectorcabinetortheremotecontrol.

CAUTION• Beforecleaningthefilter,firstturnoffthepower,makesurethecoolingfanhascompletelystopped,thenturnoffthemainpowerswitch.Makesuretheunithascooleddowncompletelybeforecleaningthefilter.Remov-ingthefiltercoverwhiletheunitisrunningcouldresultinburnsorelectricshockfromcontactwithinternalparts.

Theunitusesathreelayermetal-meshfilterinstalledbehindthefiltercover.Itcanbeusedrepeatedlybyperiodicalcleaning.Therearefourfiltersintotal,locatedontherightandleftsides.Cleanallfouratthesametime.

Filtercover/Filter

1. Removethefiltercover.

(1)Twisttheknobtotheleftuntilitturnswithoutresistance.

(2)Openthefiltercoverandremoveit.

• Theknobdoesnotcomeoff.

• If the knob will not turn, use a Phillips head screw-driver.

1

2

54

5. Maintenance

2. Undothelockleveronthefiltercoverandremoveit.

Ifthefiltergetscaughtonthefiltercover,pressthefiltercoverdownslightlyanditwillcomeout. A

B

3. Removethefilters.

(1)Turnthetabstotheleftpositionandslidethetopfiltertotheright.

TabTabsintherear

• If it is stuck, slowly inserting the tip of a Phillips headscrewdriverintothegapinafewplaceswillloosenit.

NOTE:• Donotapplyahighdegreeofforceorattempttopryitopen.Thiscoulddeformtheflangemakingit impossibletoreattachthefiltercover.

(2)Withthetabsstillontheleft-facingposition,removethefilterinsidebypullingittowardyou.

Allthreelayersofthefilterwillcomeout.

4. Cleanallthedustfromthefiltersusingavacuumclean-er.

Carefullyremovethedustfromthefiltercoversaswellasfrombothsidesofallthefilters.

55

5. Maintenance

Removethedustfromthegratesontheoutsideoftheprojec-toraswell.

• Some intakeventsdonothavegrates.Besure toalsoremoveanydust stuck to the louver (blindwithangledhorizontalslats)withavacuumcleaner.

NOTE:• Wheneveryouvacuumthefilter,usethesoftbrushattachmenttovacuum.Thisistoavoiddamagetothefilter.

• Donotwashthefilterwithwater.Doingsocanresultindamagetothefiltermembraneandalsocauseclogging.

Thegratesontheoutsideoftheprojector

5. Putthevariouspartsofthefiltertogetherandfittheminsidethefiltercover.

Thethreelayersofthefiltermustbeassembledandinstalledinaparticularorderanddirection.Finegradefilter Mediumgradefilter Coarsegradefilter

(1)Turnthetabsonthefinegradefiltertotheleft,turnthetabson themediumgradefilter (withdiagonalcrossedmesh)totheright,thenslidethefinegradefilterintothemediumgradefilter.

Thetabsonthefinegradefilter

Thetabsonthemediumgradefilter

(2)Turnthetabslotsonthecoarsegradefiltertotheleft.Nextsetthefinegradefilterandthemediumgradefilterintotheflange,thenslidethemtotheleft.

Thetabslotsonthecoarsegradefilter

Finegradefilter Mediumgradefilter

(3)Makesurethatallsixtabsareslightlyintothetabslots,thenslowlypushthefiltertogether(somefiltershavetentabs).

• Ifthepartsofthefilterarenotcompletelyfittedtogethertheywillnotfitinsidethefiltercover.

56

5. Maintenance

(4)Turn thefinegradefilterso it is facingupward,set thecutoutportionofthemediumgradefilterinsidethefiltercoveralongthedirectionindicatedbythetabs,andslowlyslidethefilterin.

Directiontabs

Cutoutportion

(5)Lockthelever,andinsertitintothelockslotonthefinegradefilter.

Lockslot

6. Fixthefilterinsidetheprojectorunit.

(1)Snap thefiltercover tabs into thecutoutportionof theprojectorunittosecureit.

(2)Turntheknobtotherighttofixitinplace.

Cleantheotherintakeventairfiltersinthesameway.

1

2

NOTE:• Beforeturningonthepowermakesurethatallfiltercoversareinplace.Iftheyarenotfittedproperlydustcouldgetinsidetheprojectorcausingittomalfunction.

• Reset[FILTERHOURSUSED]aftercleaningthefilters.Toresetgototheonscreenmenuandselect[SETUP]→[RESET]→[CLEARFILTERHOURS].

57

5. Maintenance

5-2. Cleaning the Lens• Turnofftheprojectorbeforecleaning.

• Useablowerorlenspapertocleanthelens,andbecarefulnottoscratchormarthelens.

WARNING• DonotlookintothelightsourcewhiletheprojectorisON.Stronglightisemittedfromtheprojectorandvisual

impairment could result.

• Pleasedonotuseaspraycontainingflammablegastoremovedustattachedtothelens,etc.Doingsomayresultinfires.

5-3. Cleaning the CabinetTurn off the projector, and unplug the projector before cleaning.• Useadrysoftclothtowipedustoffthecabinet.

If heavily soiled, use a mild detergent.

• Neverusestrongdetergentsorsolventssuchasalcoholorthinner.

• Whencleaningtheventilationslitsorthespeakerusingavacuumcleaner,donotforcethebrushofthevacuumcleaner into the slits of the cabinet.

Vacuumthedustofftheventilationslits.

• Poorventilationcausedbydustaccumulationinventilationopenings(intake,exhaust)canresultinoverheatingand malfunction. These areas should be cleaned regularly.

• Donotscratchorhitthecabinetwithyourfingersoranyhardobjects

• Contactyourdealerforcleaningtheinsideoftheprojector.

NOTE:Donotapplyvolatileagentsuchasinsecticideonthecabinet,thelens,orthescreen.Donotleavearubberorvinylproductinprolongedcontactwithit.Otherwisethesurfacefinishwillbedeterioratedorthecoatingmaybestrippedoff.

58

6. Appendix6-1. Compatible Input Signal ListAnalog Computer Signal

Signal Resolution ( dots ) Aspect Ratio RefreshRate(Hz)VGA 640 × 480 4 : 3 60/72/75/85/iMacSVGA 800 × 600 4 : 3 56/60/72/75/85/iMacXGA 1024 × 768 4 : 3 60/70/75/85/iMacXGA+ 1152 × 864 4 : 3 60/70/75/85

WXGA

1280 × 768 15 : 9 601280 × 800 16 : 10 601360 × 768 *2 16 : 9 601366 × 768 *2 16 : 9 60

Quad-VGA 1280 × 960 4 : 3 60/75/85SXGA 1280 × 1024 5 : 4 60/75/85SXGA+ 1400 × 1050 4 : 3 60/75WXGA+ 1440 × 900 16 : 10 60WXGA++ 1600 × 900 16 : 9 60UXGA 1600 × 1200 4 : 3 60/65/70/75WSXGA+ 1680 × 1050 16 : 10 60WUXGA 1920 × 1200 16 : 10 60(ReducedBlanking)2K 2048 × 1080 17 : 9 60Full HD 1920 × 1080 *1 16 : 9 60MAC13" 640 × 480 4 : 3 67MAC16" 832 × 624 4 : 3 75MAC19" 1024 × 768 4 : 3 75MAC21" 1152 × 870 *3 4 : 3 75MAC23" 1280 × 1024 5 : 4 65

ComponentSignal Resolution ( dots ) Aspect Ratio RefreshRate(Hz)

HDTV(1080p) 1920 × 1080 16 : 9 50/60HDTV(1080i) 1920 × 1080 16 : 9 50/60HDTV (720p) 1280 × 720 16 : 9 50/60SDTV(480p) 720 × 480 4:3/16:9 60SDTV(576p) 720 × 576 4:3/16:9 50SDTV(480i) 720 × 480 4:3/16:9 60SDTV(576i) 720 × 576 4:3/16:9 50

Composite Video/S-VideoSignal Aspect Ratio RefreshRate(Hz)

NTSC 4 : 3 60PAL 4 : 3 50PAL60 4 : 3 60SECAM 4 : 3 50

59

6. Appendix

HDMISignal Resolution ( dots ) Aspect Ratio RefreshRate(Hz)

VGA 640 × 480 4 : 3 60SVGA 800 × 600 4 : 3 60XGA 1024 × 768 4 : 3 60HD 1280 × 720 16 : 9 60

WXGA1280 × 768 15 : 9 601280 × 800 16 : 10 601366 × 768 *2 16 : 9 60

Quad-VGA 1280 × 960 4 : 3 60SXGA 1280 × 1024 5 : 4 60SXGA+ 1400 × 1050 4 : 3 60WXGA+ 1440 × 900 16 : 10 60WXGA++ 1600 × 900 16 : 9 60WSXGA+ 1680 × 1050 16 : 10 60UXGA 1600 × 1200 4 : 3 60Full HD 1920 × 1080 *1 16 : 9 60WUXGA 1920 × 1200 16 : 10 60(ReducedBlanking)2K 2048 × 1080 17 : 9 60WQHD iMac27"

2560 × 1440 16 : 9 60

WQXGA 2560 × 1600 16 : 10 60(ReducedBlanking)

4K3840 × 2160 16 : 9 23.98/24/25/29.97/304096 × 2160 17 : 9 24

HDTV(1080p) 1920 × 1080 16 : 9 50/60HDTV(1080i) 1920 × 1080 16 : 9 50/60HDTV (720p) 1280 × 720 16 : 9 50/60SDTV(480i/p) 720/1440 × 480 4:3/16:9 60SDTV(576i/p) 720/1440 × 576 4:3/16:9 50

HDMI 3DSignalResolution(dots) RefreshRate(Hz) Aspect Ratio 3D Format

1920 × 1080p23.98/24

16 : 9

Frame PackingTopandBottom

50 SideBySide59.94/60 SideBySide

1920 × 1080i50 SideBySide

59.94/60 SideBySide

1280 × 720p

50Frame PackingSideBySideTopandBottom

59.94/60Frame PackingSideBySideTopandBottom

60

6. Appendix

DisplayPortSignal Resolution ( dots ) Aspect Ratio RefreshRate(Hz)

VGA 640 × 480 4 : 3 60SVGA 800 × 600 4 : 3 60XGA 1024 × 768 4 : 3 60HD 1280 × 720 16 : 9 60

WXGA1280 × 768 15 : 9 601280 × 800 16 : 10 601366 × 768 *2 16 : 9 60

Quad-VGA 1280 × 960 4 : 3 60SXGA 1280 × 1024 5 : 4 60SXGA+ 1400 × 1050 4 : 3 60WXGA+ 1440 × 900 16 : 10 60WXGA++ 1600 × 900 16 : 9 60WSXGA+ 1680 × 1050 16 : 10 60UXGA 1600 × 1200 4 : 3 60Full HD 1920 × 1080 *1 16 : 9 60WUXGA 1920 × 1200 16 : 10 60(ReducedBlanking)2K 2048 × 1080 17 : 9 60WQHD iMac27"

2560 × 1440 16 : 9 60

WQXGA 2560 × 1600 16 : 10 60(ReducedBlanking)

4K3840 × 2160 16 : 9 23.98/24/25/29.97/304096 × 2160 17 : 9 24

HDTV(1080p) 1920 × 1080 16 : 9 50/60HDTV (720p) 1280 × 720 16 : 9 50/60SDTV(480i/p) 720/1440 × 480 4:3/16:9 60SDTV(576i/p) 720/1440 × 576 4:3/16:9 50

DisplayPort 3DSignalResolution(dots) RefreshRate(Hz) Aspect Ratio 3D Format

1920 × 1080p

23.98/24

16 : 9

SideBySideTopandBottom

25SideBySideTopandBottom

50SideBySideTopandBottom

59.94/60SideBySideTopandBottom

1920 × 1080i50

TopandBottomSideBySide

59.94/60TopandBottomSideBySide

1280 × 720p50

SideBySideTopandBottom

59.94/60SideBySideTopandBottom

*1 Native resolution*2 Theprojectormayfailtodisplaythesesignalscorrectlywhen[AUTO]isselectedfor[ASPECTRATIO]intheon-screenmenu. Thefactorydefaultis[AUTO]for[ASPECTRATIO].Todisplaythesesignals,select[16:9]for[ASPECTRATIO].*3 Theprojectormayfailtodisplaythesesignalscorrectlywhen[AUTO]isselectedfor[ASPECTRATIO]intheon-screenmenu. Thefactorydefaultis[AUTO]for[ASPECTRATIO].Todisplaythesesignals,select[4:3]for[ASPECTRATIO].

• Signalsexceedingtheprojector’sresolutionarehandledwithAdvancedAccuBlend.• WithAdvancedAccuBlend,thesizeofcharactersandruledlinesmaybeunevenandcolorsmaybeblurred.• Uponshipment,theprojectorissetforsignalswithstandarddisplayresolutionsandfrequencies,butadjustmentsmayberequired

depending on the type of computer.

61

6. Appendix

6-2. TroubleshootingThis section helps you resolve problems you may encounter while setting up or using the projector.

Indicator Messages

POWER Indicator

Indicator display Projector status Procedure

Off Power is off. –

Flashing Blue(shortflashes) Preparing to turn power on Waitawhile.

Blue(longflashes) Offtimer(enabled)Program timer (off time enabled)

–

Orange(shortflashes) Projector cooling Waitawhile.

Orange(longflashes) Program timer (on time enabled) –

Lit Blue Power on –

Red Standbymode(NORMAL) –

Orange Standbymode(HDBaseTSTANDBY) –

STATUS Indicator


Off Noproblem,orSTAND-BYMODE-“HDBaseTSTANDBY”

–

Flashing Red (once per cycle)

Problem with the cover Check to make sure the lens cover, top cover, side cover, andlensunitareallcorrectlyfixedinplace.

Red (3 times per cycle)

Power failure Problemwiththepowersystem.ContacttheNECprojectorcustomer support center to arrange for repair.

Red (4 times per cycle)

Problem with the fan Rotationofthecoolingfanhasstopped.ContacttheNECprojector customer support center to arrange for repair.

Red(6timesper cycle)

Problem with the light source

Problemwith the lightsourcesystem.Contact theNECprojector customer support center to arrange for repair.

Red(9timesper cycle)

Hardware problem Problemwith the hardware.Contact theNECprojectorcustomer support center to arrange for repair.

Lit Green STANDBYMODEinsleep mode*

–

Orange Buttonhasbeenpressed while projector is in key lock mode

The projector’s For releasing the key lock setting, press and holdKEYLOCKbuttononthecabinetover1second.

Projector’s ID number and remote control’s ID number do not match

Check the control IDs. (→ Pages 52)

* Sleepmodereferstothestatewherebythefunctionalrestrictionsduetothestandbymodesettingareremoved.

62

6. Appendix

LIGHT Indicator


Off The light module is turned off.

–

Flashing Green TransitiontoswitchON/OFFthelightmodule

–

Lit Green Light module lit –

TEMP. Indicator


Off No problem

Flashing Red (cycles of 2)

Temperature problem The temperature protector has been activated. If the room temperature is high, move the projector to a cool place. If theproblemstillpersists,contactanNECprojectorcus-tomer support center.

Lit Orange High surrounding tem-perature(ForcedECOMode)

The surrounding temperature is high. Lower the room temperature.

SHUTTER Indicator

Indicator display Projector status

Off Openshutter

Flashing Green [LENSCALIBRATION]inprogress

Lit Green Shutterclosed

KEY LOCK Indicator

Indicator display Projector status

Off [CONTROLPANELLOCK][OFF]

Lit Orange [CONTROLPANELLOCK][ON]

If the temperature protector is activatedIf the projector’s internal temperature rises abnormally, the light module turns off and the temperature indicator flashes (repeatedly in cycles of 2).It may happen that the projector’s temperature protector is simultaneously activated and the projector’s power turns off.Ifthishappens,dothefollowing:- Unplugthepowercordfromthepoweroutlet.

- If using in a place where the surrounding temperature is high, move the projector to a different, cool place.

- If there is dust in the ventilation holes, clean. (→ page 53)

- Waitassuchabout1hourfortheprojector’sinternaltemperaturetolower.

63

6. Appendix

6-3. Pin assignments and signal names of main terminalsCOMPUTER IN/ Component Input Terminal (Mini D-Sub 15 Pin)

Connection and signal level of each pin

51 42 310

11 12 13 14 156 97 8

Signal LevelVideosignal:0.7Vp-p(Analog)Syncsignal:TTLlevel

Pin No. RGB Signal (Analog) YCbCr Signal1 Red Cr2 GreenorSynconGreen Y3 Blue Cb4 Ground5 Ground6 Red Ground Cr Ground7 Green Ground YGround8 BlueGround Cb Ground9 No Connection

10 SyncSignalGround11 No Connection12 Bi-directionalDATA(SDA)13 HorizontalSyncorCompositeSync14 VerticalSync15 Data Clock

HDMI IN Terminal (Type A)

1 3 5 7 9 11 13 15 17 192 4 6 8 10 12 14 16 18

Pin No. Signal Pin No. Signal1 TMDSData2+ 11 TMDSClockShield2 TMDSData2Shield 12 TMDSClock−3 TMDSData2− 13 CEC4 TMDSData1+ 14 Disconnection5 TMDSData1Shield 15 SCL6 TMDSData1− 16 SDA7 TMDSData0+ 17 DDC/CECgrounding8 TMDSData0Shield 18 +5 V power supply9 TMDSData0− 19 Hot plug detection10 TMDSClock+

DisplayPort IN Terminal

1 3 5 7 9 11 13 15 17 192 4 6 8 10 12 14 16 18 20

Pin No. Signal Pin No. Signal1 Mainlinklane3− 11 Grounding 02 Grounding 3 12 Main link lane 0+3 Main link lane 3+ 13 Configuration14 Mainlinklane2− 14 Configuration25 Grounding 2 15 Supplementarychannel+6 Main link lane 2+ 16 Grounding 47 Mainlinklane1− 17 Supplementarychannel−8 Grounding 1 18 Hot plug detection9 Main link lane 1+ 19 Return10 Mainlinklane0− 20 +3.3 V power supply

64

6. Appendix

Ethernet/HDBaseT Port (RJ-45)

1 2 3 4 5 6 7 8

Pin No. Signal1 TxD+/HDBT0+2 TxD−/HDBT0−3 RxD+/HDBT1+4 Disconnection/HDBT2+5 Disconnection/HDBT2−6 RxD−/HDBT1−7 Disconnection/HDBT3+8 Disconnection/HDBT3−

USB Port (Type A)

1

3

2

4

Pin No. Signal1 VBUS2 D−3 D+4 Grounding

RS-232C terminal (PC control) (D-Sub 9 Pin)

12345

6789

Communications protocol

Pin No. Signal1 Unused2 Transmission data3 Reception data4 Connection/Pin65 Grounding6 Connection/Pin 47 Unused8 Unused9 Unused

65

6. Appendix

3D connector (D-sub 15 pin)

8 7 6 5 4 3 2 1

15 14 13 12 11 10 9

Pin No. Signal Name I/O Function1 +12V PWR Suppliespower(+12V)tothe3Dimagesystem2 GNDC GND Ground3 GNDC GND Ground4 reserved IN5 reserved OUT6 reserved OUT7 CONN_SYNC+ OUT 3D L/R switching timing signal (+)

(Connects to the collector of the output transistor of the photo coupler inside the projector)

8 reserved IN9 +12V PWR Suppliespower(+12V)tothe3Dimagesystem10 reserved IN11 reserved IN12 reserved IN13 reserved OUT14 CONN_SYNC− OUT 3DL/Rswitchingtimingsignal(–)

(Connects to the emitter of the output transistor of the photo coupler inside the projector)

15 N/C — Unused

66

6. Appendix

GP I/O terminal (External control) (D-sub 37 pin)

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

37 26 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20

Pin No. Signal Name I/O1 reserved IN2 reserved IN3 reserved4 reserved5 EXT_GPIN1+(Control) IN6 EXT_GPIN2+(Control) IN7 EXT_GPIN3+(Control) IN8 EXT_GPIN4+(Control) IN9 GPOUT1+(External3DL/ROutput

Reference +)OUT

10 reserved OUT11 reserved OUT12 reserved OUT13 reserved OUT14 reserved OUT15 reserved OUT16 reserved OUT17 NC (not connected) —18 GND PWR19 GND PWR

Pin No. Signal Name I/O20 reserved IN21 reserved IN22 reserved IN23 reserved IN24 EXT_GPIN1-(Control) IN25 EXT_GPIN2-(Control) IN26 EXT_GPIN3-(Control) IN27 EXT_GPIN4-(Control) IN28 GPOUT1-(External3DL/ROutput

Reference -)OUT

29 reserved OUT30 reserved OUT31 reserved OUT32 reserved OUT33 reserved OUT34 reserved OUT35 reserved OUT36 NC (not connected) -37 GND PWR

67

6. Appendix

Inside Projector

Voltage applied across the pins of Ext_GPIN_P and Ext_GPIN_N should be in the range from 3.3 Vdc to 10 Vdc. Recommended Operating Current: 5 mAAbsolute Maximum Rating: 23 mA

Resist = 360 Ω

Photo-couplerForward direction voltage: 1.1 V (@5 mA)

GP I/O Connector

Pin No.: 5 6 7 8

Pin No.: 24 25 26 27

Ext_GPIN_P

Ext_GPIN_N

Using GPIO ControlMomentary“ON”pulseenablesyoutocontrolprojector.Toenable“ON”pulse,holditforatleast300ms.Hold“OFF”foratleast300msbefore“ON”.(→ page 68)HereisfunctionlisttocontrolprojectorbyusingGPIOport.

Photo-coupler ON/OFF Function8-27 7-26 6-25 5-24 The following functions apply depending on the combination of input

terminals.OFF OFF OFF ON PowerONOFF OFF ON OFF PowerOFFOFF OFF ON ON ShuttercloseOFF ON OFF OFF ShutteropenOFF ON OFF ON SelectHDMIOFF ON ON OFF SelectDisplayPortOFF ON ON ON SelectBNCON OFF OFF OFF SelectBNC(CV)ON OFF OFF ON SelectBNC(Y/C)ON OFF ON OFF SelectComputerON OFF ON ON SelectHDBaseTON ON OFF OFF SelectSLOTON ON OFF ON reservedON ON ON OFF reservedON ON ON ON reserved

Exampleforturningoffthepowersource(Shutterclose):InputONto6-25and5-24while8-27and7-26areOFF.

NOTE:• TheoperationcommandcomingfromGPI/Oportwillbecanceledwhentheprojectorisprocessingothertasks.• Setallotherpinsthanthoseinuseto“OFF”.• Theoperationcommandisexecuteduponcontinuousinputofthe“ON”pulseforapproximately300ms.

68

6. Appendix

Timing chart of GPIO controlExample of Select HDMI

Off at least 300 ms at least 300 ms

approx. 300 ms

ExecuteSelect HDMI

time

5-24/7-26

6-25/8-27

on

off

on

off

69

6. Appendix

Remote Interlock TerminalThisterminalfunctionsassafetydevicefortheprojector.Thecontactsarenormallyclosed.Whenanabnormalityoccurs, the contacts open to immediately stop the projector (interlock state) (shipped with a shorting bar installed). Byreplacingtheshortingbarwithwiringandattachingittothecontacts,theprojectorcanbeimmediatelystoppedremotely when an abnormality occurs in the projector.

Follow the following procedure to recover from the interlock state.

1. DisconnecttheACpowersupplytotheprojectorunit.

2. Closethecontacttotheremoteinterlockterminal.

3. ConnecttheACpowersupplytotheprojectorunit.

Remote interlock terminal (exterior view)

#4

#3

#2

#1

Shortingbar2

Shortingbar1

Clampforsettlingcables

• Theremoteinterlockterminalisequippedoninsideofthelenscover.

Remove the lens cover for connection.

• Securelyreinstallthelenscover.

• Thebottomsideofthelenscoverisnotched.Settletheconnectedcablesbytheclampundertheterminalanddraw them out to out of the projector from the notch.

Circuit diagram

Shorting bar 1

Shorting bar 2

Interlock terminal Inside projector

780Ω/1W resistor

GND#4

4

4

3 3

2

2

1

1

1

#3

#2

#1500mA fuse

VCC +5V

Photocoupler

Terminal no. PhotocouplerON/OFF Description#1 - +5V supply#2 ON/OFF Connects to the photocoupler anode inside the projector#3 Connects to the photocoupler cathode inside the projector#4 - Ground

70

6. Appendix

• When the length of the wiring is less than 5 m (approximate)Remove the shorting bar 1 or the shorting bar 2 and connect the terminal (#1/#2 or #3/#4) to the contact.

- An external power supply is not necessary.

- A maximum of 2 sets of contacts can be connected (when both the shorting bar 1 and the shorting bar 2 are removed.)

- The minimum rating for the contact is as below.

Voltage Minimum rated current5V or less 2mA or less

• When the length of the wiring is at least 5 m (approximate)Remove the shorting bar 1 and the shorting bar 2 and connect an external power supply and the contact to the ter-minals (#2 and #3) in series (do not use #1 and #4.)

- Connect #2 to the positive side of an external power supply, and connect #3 to the negative side of the external power supply.

- Thevoltagefortheconnectingexternalpowersupplyshouldbewithinarangeof5Vminimumto16Vmaximum.The minimum rating for the contact depends on the voltage of the external power supply.

Voltage Minimum rated current5V 2mA16V 18mA

71

6. Appendix

6-4. Cabinet Dimensions

Unit:mm(inch)

680 (26.8)

744

(29.

3)

164.

5 (6

.5)

333

(13.

1)

45.2 (1.8)566 (22.3)

928.

5 (3

6.6)

1081

(42.

6)

860

(33.

9)

Lenscenter

In EuropeNECDisplaySolutionsEuropeGmbHAddress:LandshuterAllee12-14D-80637München,GermanyTelephone:+4989996990Email:[email protected]

In North AmericaNECDisplaySolutionsofAmerica,Inc.Address:500ParkBoulevard,Suite1100Itasca,Illinois60143,U.S.A.Telephone:+18008360655

In OceaniaAustraliaAWALimited.Address:151ArthurStreetHomebushWestNSW2140AustraliaCustomer Call CentreTelephone:0297647777EmailAddress:[email protected]

New ZealandVisual Group Ltd.Address: 28WallsRoadPenroseAucklandNewZea-landTelephone:095250740EmailAddress:[email protected]

In South AmericaBrazilVideocorpBrasilAddress:AvenidaConselheiroRodriguesAlvesNro.820/Sala15-2°Andar - Vila MarianaSãoPaulo-SP-BrasilCEP04014-002Telefone:+55-11-2924.2910/+55-11-2924.2911

In AsiaNECDisplaySolutions,Ltd.Address:686-1,Nishioi,Oi-Machi,Ashigarakami-Gun,Kanagawa258-8533,JapanTelephone:+81465852369

NECSolutions(China)Co.,Ltd.Address:Rm1903,ShiningBuilding,35XueyuanRd,HaidianDistrictBeijing100191,P.R.C.Telephone:+861059342706

NECHongKongLtd.Address:25/F.,TheMetropolisTower,10MetropolisDrive,Hunghom,Kowloon,HongKongTelephone:+85223690335

NECTaiwanLtd.Address:7F,No.167,SEC.2,NanKingEastRoad,Taipei,Taiwan,R.O.C.Telephone:+886285001710

NECAsiaPacificPteLtd.Address:401CommonwealthDrive,#07-02,HawParTechnocentre,Singapore149598Telephone:+6567996188

NECCorporationofMalaysiaSdn.Bhd.Address:33rdFloor,MenaraTAOne,22,JalanP.Ramlee,50250KualaLumpur,MalaysiaTelephone:+60321783600(ISDN)

©NECDisplaySolutions,Ltd.2015Ver. 1 4/15

Date post:	30-May-2018
Category:	Documents
Upload:	truongkhanh
View:	235 times
Download:	0 times

DLP Projector PH1202HL/PH1002HL - NEC Display … Projector PH1202HL/PH1002HL Installation Manual...

Documents