Inventory and monitoring toolbox: freshwater ecology
DOCDM-766000
This specification was prepared by Duncan Gray in 2013.
Contents
Synopsis .......................................................................................................................................... 2
Assumptions .................................................................................................................................... 3
Advantages ...................................................................................................................................... 3
Disadvantages ................................................................................................................................. 3
Suitability for inventory ..................................................................................................................... 4
Suitability for monitoring ................................................................................................................... 4
Skills ................................................................................................................................................ 4
Resources ....................................................................................................................................... 4
Minimum attributes .......................................................................................................................... 5
Data storage .................................................................................................................................... 6
Analysis, interpretation and reporting ............................................................................................... 7
Case study A ................................................................................................................................... 8
Full details of technique and best practice ......................................................................................11
References and further reading ......................................................................................................13
Appendix A .....................................................................................................................................15
Freshwater ecology: quantitative periphyton biomass sampling methods
Version 1.0
Disclaimer This document contains supporting material for the Inventory and Monitoring Toolbox, which contains DOC’s biodiversity inventory and monitoring standards. It is being made available to external groups and organisations to demonstrate current departmental best practice. DOC has used its best endeavours to ensure the accuracy of the information at the date of publication. As these standards have been prepared for the use of DOC staff, other users may require authorisation or caveats may apply. Any use by members of the public is at their own risk and DOC disclaims any liability that may arise from its use. For further information, please email [email protected]
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 2
Inventory and monitoring toolbox: freshwater ecology
Synopsis
Quantitative sampling methods 1a and 1b are based on that presented by Biggs & Kilroy (2000).
These methods are designed to provide data suitable for statistical testing of differences amongst
sites to detect impact effects. Sampling points are located along a single transect and 10 points
sampled. The methods described here are suitable for gravel or cobble substrate, but protocols for
bedrock/boulder or sand/silt substrates are also described in Biggs & Kilroy (2000). These methods
estimate biomass for a known area of the entire exposed (1a) or upper (1b) surface of stones.
Method 1a is suitable for general enrichment assessments and ecological studies of in-stream
processes. Method 1b provides more precise information about the response of periphyton
community biomass to specific impacts. Results are expressed in terms of surface area of exposed
sediments (1a) or in terms of plane surface area of the stream bed (1b).
The choice between 1a and 1b is dictated by the objectives of the study and pragmatism. Method
1a samples the entire stone periphyton community and assesses the entire diversity of microhabitat
types around the stone. However, there will be little difference between communities on a particle
when substrates are fine cobbles and gravel. Greater heterogeneity in biomass will be found around
moderate-sized cobbles and larger substrates where whole stone sampling can provide more
information about the overall community. Conversely, method 1b helps remove the effects of spatial
differences in water velocity, erosion of communities along the edge of substrata, and the effects of
grazing invertebrates that usually spend most of their time under or along the edges of particles.
Accordingly this method is very suitable for assessments of organic enrichment from a specific
discharge. The available range of analytical techniques is the same for both techniques. The detail
in this protocol can be applied to each method except where noted.
All quantitative sampling methods must account for the level of variation within a site and the
consequent degree of error associated with sampling. Greater heterogeneity in periphyton cover
may require the number of replicates to be increased. However, in general it is recommended to
collect at least 10 replicate samples per site. These are most often collected as point samples along
a transect across the river channel. An in-depth discussion of methods for calculating error and
estimating the required number of replicates may be found in Biggs & Kilroy (2000, section 3).
Repeated surveys at regular intervals allow a comprehensive picture of periphyton community
dynamics to be created. Results may be combined with environmental data to assess the factors
which influence periphyton biomass.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 3
Inventory and monitoring toolbox: freshwater ecology
Figure 1. Examples of periphyton types commonly associated with nutrient enrichment and stable flows in streams.
Top left: medium, possibly thick, dark brown mats. Top right: medium thickness green mat. Bottom left: long brown
filaments adhere to rocks adjacent to a tracer stone used to measure stream bed movement. Bottom right: medium
thickness dark brown mats and short green filamentous algae. Photos: Golder Associates.
Assumptions
Methods (1a or 1b) assume that the physical habitat conditions at each site vary as little as
possible.
Probability based sampling (usually simple random or systematic designs) are applied to
positioning of transects and points within a transect at each site.
All biomass within the sample area is collected.
The sample represents periphyton biomass in the wider stream area of interest.
Advantages
Provides reliable, precise and detailed information about periphyton biomass in a stream reach.
Robust against user bias provided the protocols are adhered to.
Disadvantages
Material may be lost or degraded during sample collection and transport, negatively biasing
estimates of biomass.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 4
Inventory and monitoring toolbox: freshwater ecology
These methods require material to be transported from the site and the use of chilled storage.
The methods incur significant laboratory processing costs.
Samples must be processed rapidly.
Stream must be wadeable.
Suitability for inventory
These methods are not very suitable for inventory because it provides no information about
community composition and data is resource-intensive to obtain, thus limited in spatial extent.
Suitability for monitoring
These methods are suitable for monitoring the effects of general enrichment (1a), or specific
impacts to a stream ecosystem (1b).
Used in conjunction with qualitative methods to assess periphyton community composition and
cover (‘RAM-1’—docdm-769146, or ‘RAM-2’—docdm-769150) and physico-chemical data,
these methods provide a powerful tool for understanding periphyton dynamics in a stream.
These methods in isolation are not suitable for assessing changes in periphyton community
composition or cover by specific periphyton types.
Skills
Field observers will require:
Basic training in stream periphyton and habitat sampling
Basic outdoor and river-crossing skills
A reasonable level of fitness
Study design and sample processing are specialised processes that require input from a TSO,
Science Officer or external contractor.
Resources
Periphyton sampling of New Zealand streams may be carried out by a single field operative.
However, in the interests of safety it is recommended that sampling is done by teams of at least two
people.
Standard equipment includes:
One 20–30 m tape measure
Two 6–10 mm diameter aluminium pegs (> 20 cm long) that are bent at one end to hold tapes in
place (a mallet for securing pegs may be useful)
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 5
Inventory and monitoring toolbox: freshwater ecology
Deep sided, white, laboratory tray container and ice container (e.g. chilly-bin)
Scalpel
Small scrubbing brushes (e.g. toothbrushes)
Labelled containers (e.g. 120 ml specimen cups; 60 ml rigid clear plastic pottles) for each
sample that will be collected.
Pipettes (small eye-dropper is sufficient)
Squirt bottle containing stream water
A ring of an appropriate size (usually 4 to 8 cm diameter) which can be used to define a
sampling circle on each stone (the top of the sample collection container can be used)
Waterproof notebook
GPS
Figure 2. An example wet label which should be added to every sample collected.
Minimum attributes
Consistent measurement and recording of these attributes is critical for the implementation of the
method. Other attributes may be optional depending on your objective. For more information refer
to ‘Full details of technique and best practice’.
DOC staff must complete a ‘Standard inventory and monitoring project plan’ (docdm-146272).
The more contextual information that is collected at each site, the more thorough and complete will
be any interpretation of the biological data collected. However, some basic information should be
recorded with each sample collected:
Substrate composition
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 6
Inventory and monitoring toolbox: freshwater ecology
Riparian vegetation
Stream width
Stream depth
Stream velocity
It is also common to collect basic water chemistry information. Temperature (°C), electrical
conductivity (µS), pH and dissolved oxygen may all be measured by handheld meters and assist
with the interpretation of biological data. Habitat and site notes are also useful, e.g. the presence of
stock at the site or evidence of recent flooding. The ‘Stream habitat assessment field sheet’
(docdm-761873) specifies the minimum attributes that can be collected without recourse to
specialised equipment or processing in a laboratory. Basic training in the use of this habitat sheet
and a thorough perusal of Harding et al. (2009) is required before use.1 As with all visual and
qualitative assessments it is important to standardise collection protocols and ensure observations
are calibrated. This is especially important if more than one observer is collecting data (e.g. if
different teams will go to different sites or will repeat measurements in the future).
Data storage
During field sampling, data is conventionally recorded on a hardcopy data sheet prior to transfer to
an electronic format. Hardcopy sheets should be clearly marked with the details of the project and
identity/location of samples. Forward copies of completed data sheets to the survey administrator,
or enter data into an appropriate spreadsheet or database as soon as possible. Collate, consolidate
and store survey information securely, also as soon as possible, preferably immediately on return
from the field. The key steps here are data entry, storage and maintenance for later analysis,
followed by copying and data backup for security.
Storage tools can be either manual or electronic systems (or both, preferably). They will usually be
summary sheets, other physical filing systems, or electronic spreadsheets and databases.
To avoid confusion, data should be entered into an electronic media in the same format as on the
field data sheets. Electronic data files should contain all the information required to identify each
sample, and any habitat or water chemistry data that was collected simultaneously should be
captured in the same files. This is often achieved by entering habitat data on a separate worksheet
within the same Excel workbook.
DOC best practice for Excel is to enter data in ‘long format’, i.e. with each field on the data sheet
(date, time, location, transect designation, sample number, quantity, etc.) as a column heading and
each row containing the values from a single sampling occasion. However, the convention for
recording freshwater ecological data is to treat each site as a separate column. It is important that
habitat and water chemistry data are entered in a comparable format to biological data, i.e. columns
as sites, and this should be done as soon as possible by the field operative so that details are fresh.
All hardcopies of habitat data and notes should be labelled and stored in a project file and retained.
1 http://www.cawthron.org.nz/coastal-freshwater-resources/downloads/stream-habitat-assessment-
protocols.pdf
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 7
Inventory and monitoring toolbox: freshwater ecology
All electronic files should have a notes sheet which contains basic metadata and any relevant
information for future users. In particular, each user, beginning with the field operative who enters
the data, should record details of any changes to the data, when and why they were made. It is also
best practice to retain a single version of the data which has undergone quality control and may not
be altered. All analysis is performed on copies of this master sheet.
Use appropriate file formats such as .xls, .txt, .dbf or specific analysis software formats. Copy
and/or backup all data, whether electronic, data sheets, metadata or site access descriptions,
preferably offline if the primary storage location is part of a networked system. Store the copy at a
separate location for security purposes.
If data storage is designed well at the outset, it will make the job of analysis and interpretation much
easier. Before storing data, check for missing information and errors, and ensure metadata are
recorded.
Analysis, interpretation and reporting
Quantitative estimates of biomass are analysed using either or both the chlorophyll a (mg/m2) or
ash-free dry mass (AFDM) (g/m2) methods. Laboratory analysis using specialist equipment is
needed to calculate these data for each sample. Once data are obtained, seek statistical advice
from a biometrician or suitably experienced person prior to undertaking any numeric analysis.
Chlorophyll a gives an indication of the total amount of autotrophic (photosynthesising) organisms in
the sample. AFDM estimates the total amount of organic material in the sample, and incorporates
living autotrophic and heterotrophic micro-organisms, plus dead periphyton, micro-invertebrates and
often some terrestrial leaf debris. It is best to analyse for both variables, which provide
complementary information. The ratio of the two variables, AFDM / chlorophyll a, is called the
autotrophic index or AI (Weber 1973). The AI indicates the proportions of the community composed
of either heterotrophic or autotrophic material. Stream communities unaffected by organic pollution,
and dominated by algae, usually contain 1–2% (by weight) of chlorophyll a. Therefore, AI values of
50–100 are characteristic of non-polluted streams with little organic detritus. Values greater than
400 indicate communities affected by organic pollution.
When periphyton growth is very sparse there may be insufficient material to perform an AFDM
analysis. In this situation only chlorophyll a can be measured. Samples will usually be sent to
external accredited laboratories for analysis because it requires experienced operators and
considerable equipment. However, if the resources are available to perform the analyses in-house,
detailed descriptions of the methods can be found in Biggs & Kilroy (2000).
The data collected using quantitative methods (1a and 1b) provides replicate estimates of
periphyton biomass from an area of the surface of (usually) 10 stones. Conventionally, within-site
data will be averaged and these averages (and the variance around the average) compared
between sites or groups of sites. If samples are collected at multiple sites across an environmental
gradient or on multiple occasions through time it will be possible to use correlation or regression
analysis to compare biomass (indicated by chlorophyll a, AFDM or the AI) to physico-chemical data.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 8
Inventory and monitoring toolbox: freshwater ecology
Alternatively, this biomass may be compared between groups or ‘treatments’ pre-defined by an
experimental manipulation or land-use type using a method such as ANOVA.
Case study A
Case study A: monitoring change in periphyton communities as a result of riparian fencing
Synopsis
Puggings Creek is a (fictional) third order stream arising in bush-covered hill country and flowing for
13 km through low-lying, intensive dairying pastoral land. The stream is subject to nutrient
enrichment and siltation due to stock access along much of its length. Local anglers and
environmentalists noticed that the periphyton growths in the streams were impinging on the benthic
biodiversity and trout fishing. Accordingly, they persuaded the farmers along the stream to fence
stock out of the waterways and reduce discharges. Quantitative periphyton samples collected
before and after fencing of the streams indicated a dramatic decline in the biomass of periphyton,
but the Autotrophic Index (AI) indicated that the stream was still subject to organic pollution after 6
months.
Objectives
Assess the effects of riparian fencing on the periphyton biomass in Puggings Creek.
Sampling design and methods
To maximise potential to detect the effect of fencing, periphyton biomass was monitored at the
lowest reach of the stream on 24 occasions during 2 months before and after fencing was carried
out with a 3-month gap after fencing to allow for changes to take place. Ten stone surface samples
were collected and scrubbed to remove all periphyton according to method 1b (Fig. 3) (although
method 1a would also have been appropriate: see ‘Full details of technique and best practice’)
(Biggs & Kilroy 2000 and references therein). The samples were chilled and sent to a laboratory for
chlorophyll a and AFDM analysis. Unfortunately, it was not possible to select a comparable
reference stream in the area.
After laboratory analysis, results for before- and after-treatment were summarised graphically using
boxplots, and the average of all before-treatment measurements was compared to the average of
after-treatment measurements using ANOVA.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 9
Inventory and monitoring toolbox: freshwater ecology
Figure 3. Quantitative periphyton sampling of a known area of the upper surface of stones, method 1b. Top left: a
randomly selected stone is placed on the bank ready for sampling. Top right: a template of known area is used to
protect the sample while all the unwanted periphyton around it is removed. Bottom left: periphyton sample after
removal of surrounding material. Bottom right: the sample is carefully collected using a toothbrush. Photos: Duncan
Gray.
Results
Before fencing to exclude stock, and riparian planting along the stream banks, the average
chlorophyll a concentration was 31 mg/m2 of stone surface (Fig. 4). This quantity exceeds the
nuisance guidelines for mean monthly chlorophyll a and confirms suspicions that benthic
biodiversity was being degraded (Biggs 2000). Ash-free dry mass (AFDM) of periphyton had an
average value of 40 g/m2 which also exceeds the nuisance biomass guideline threshold for trout
angling/habitat. This resulted in an AI with a mean value of 1334 which indicates a stream with
severe organic pollution (Weber 1973). However, after fencing, both chlorophyll a and AFDM
measures of periphyton biomass fell to 19 mg/m2 and 12 g/m2, respectively, below the nuisance
threshold in the case of AFDM. The average AI declined to 806 which, although still indicative of an
organically enriched stream, is a considerable improvement. Differences were shown to be
statistically significant using ANOVA p < 0.05.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 10
Inventory and monitoring toolbox: freshwater ecology
Figure 4. The average values of chlorophyll a, AFDM and AI before and after fencing prevented stock access to
Puggings Creek.
The decrease in chlorophyll a was less dramatic than that seen for AFDM suggesting that the
stream is still quite productive in terms of autotrophic production. The sharper decline in AFDM may
be due to the reduction of direct additions of organic matter into the water by defecating stock,
which would in itself contribute to AFDM and also encourage proliferation of heterotrophic
organisms feeding on that matter. AI was consistently high prior to fencing, but after the removal of
stock, variation in both chlorophyll a and AFDM created a large range in AI values.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 11
Inventory and monitoring toolbox: freshwater ecology
Limitations and points to consider
This case study clearly demonstrates the response of periphyton communities to riparian fencing to
prevent stock access to a stream. It would be informative to sample again after 1 year to allow the
changes in periphyton biomass to settle after fencing. There are likely to be considerable stocks of
organic matter and available nutrients contained within the stream reach which have to be depleted
before a new periphyton community equilibrium can be achieved.
Sampling the whole stone (method 1a) rather than the upper surface may have been more sensitive
at detecting whole stream changes, but it would likely take a longer period of time before the metric
settled down compared to the stone surface method.
There is no measure of flow variability or nutrient concentrations in this study. This and any other
basic stream habitat information is always very useful to make a full interpretation of periphyton
data.
The lack of a control stream is unfortunate as it is not possible to discount seasonal effects on the
periphyton community creating the observed changes independent of the impact of fencing and
riparian planting.
One way to increase the reliability of the study in this situation would be to include multiple before
and after measurements over a longer timeframe and/or at different distances up-stream and
associate each measurement with reach-level habitat data, and data about seasonally variable
factors such as water temperature and light intensity.
References for case study A
Biggs, B.J.F. 2000: New Zealand periphyton guideline: detecting, monitoring and managing enrichment
in streams. Prepared for the Ministry for the Environment. National Institute of Water and
Atmospheric Research, Christchurch.
Biggs, B.J.F.; Kilroy, C. 2000: Stream periphyton monitoring manual. Prepared for the New Zealand
Ministry for the Environment, National Institute of Water and Atmospheric Research,
Christchurch.
Weber, C.I. 1973. Biological field and laboratory methods for measuring the quality of surface waters
and effluents. U.S. Environmental Protection Agency Report 670 / 4 / 73 / 001.
Full details of technique and best practice
Details of technique and best practice for this method are explained here. A full description of the
method is given in Biggs & Kilroy (2000).
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 12
Inventory and monitoring toolbox: freshwater ecology
Monitoring project design
Each sample location consists of a single transect across the stream. Ten point samples are taken
from each transect. If multiple transects will be sampled in a single day it is best to start
downstream and work up.
Collecting habitat data and notes
Use GPS to navigate to each pre-determined sample location.
At each location, collect basic habitat assessment data (refer to ‘Minimum attributes’ section)
and note relevant contextual information (e.g. presence of stock or indigenous species, flow
conditions). Collect this information prior to sampling the stream.
If required for a particular project, additional abiotic or habitat data may be collected.
Setting out transects
Use GPS to find the point on the stream bank that is closest to the pre-determined sample
location and on one bank drive a peg into the ground.
Attach the tape measure to the peg and lay it out taut across the stream. The tape should be
perpendicular to the stream (so that it crosses from bank to bank in the shortest possible
distance). Anchor the far end with the second peg.
Using the distances on the tape measure, divide the width of the stream (water’s edge to water’s
edge) into 10 equally spaced intervals. Each of these will be one sampling location.
Collecting samples
Move out to the first point across the transect (this will be near the water’s edge on one side of
the stream). Bend down and lightly touch the bed sediments without looking at what is there.
Ideally, pick the first stone that you touch. If it is too big to retrieve, then take the nearest one that
can be picked up. If you touch small silty or sandy patch among the cobbles, then also take the
nearest stone that can be picked up.
Place the stone on the white tray with a small amount of stream water and return it to the stream
bank.
Method 1a: whole stone surface sample:
Use the scalpel to scrape off any filamentous algae and thick growths of brown algae from the
stone. Wash onto the tray using minimal water from the squirt bottle.
Use the brush(es) to scrub the stone thoroughly. Periodically rinse off the stone and brush into
the tray. Scrub all sides of the stone to remove as much periphyton as possible. A standard
scrubbing time of 2 minutes is suggested for cobble sized material.
Transfer the contents of the white tray into your sample container (you may need to use a funnel
if you have a narrow-necked bottle).
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 13
Inventory and monitoring toolbox: freshwater ecology
Finally, rinse the tray into the sample container until no trace of periphyton remains.
Measure the x, y and z dimensions of the stone with the plastic callipers.
Proceed to the next sampling point and repeat the above procedures.
Method 1b: known area sample from the upper surface of a stone:
Place the ring on top of the stone and score/scrub around the outside of the ring with the tip of a
scalpel blade or brush. Then, scrape away all the surrounding periphyton from the outside of the
ring and discard into the stream.
Remove the ring and then scrape off as much periphyton growth as possible from within the
circle and rinse it off the scalpel into an appropriately labelled container. (Note: only use small
amounts of wash water because you will quickly run out of space in the containers).
Scrub the defined area for 30 seconds with a toothbrush and then remove the slurry from the
circle using the small pipette.
Rinse the area with a minimal amount of water. Remove any surplus water using the pipette and
transfer into the sample container. Thoroughly rinse the brush into the container.
Finally, rinse the tray on which the stone was resting into the sample container until no trace of
periphyton remains.
If the sampling point falls over a mat of filaments streaming in the current then a slightly different
approach is required for sample collection. Slide your hand underneath the filaments and gently
lift them to the surface taking care to not disturb their alignment. Take the ring used for defining
a set area and press it down firmly on top of the filaments and into the palm of your flat hand.
This action will cut a core out of the mat which then becomes your sample. If necessary, use fine
nail scissors to cut the filaments from around the edge of the ring.
Methods 1a and 1b:
Store the labelled container of periphyton sample on ice in a chilly-bin for transport to the
laboratory.
Ideally samples are analysed immediately but if storage is required, freezing at < −10°C is
recommended for periods of up to a few months but no longer. Chemical preservatives are also
available but constitute a health risk (Biggs & Kilroy 2000).
References and further reading
Biggs, B.J.F. 2000: New Zealand periphyton guideline: detecting, monitoring and managing enrichment
in streams. Prepared for the Ministry for the Environment. National Institute of Water and
Atmospheric Research, Christchurch.
Biggs, B.J.F.; Kilroy, C. 2000: Stream periphyton monitoring manual. Prepared for the New Zealand
Ministry for the Environment. National Institute of Water and Atmospheric Research,
Christchurch.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 14
Inventory and monitoring toolbox: freshwater ecology
Biggs, B.J.F.; Kilroy, C.; Mulcock, C.M. 1998: New Zealand stream monitoring and assessment kit.
Stream monitoring manual. Version 1. NIWA Technical Report 40. 150 p.
Harding, J.S.; Clapcott, J.; Quinn, J.; Hayes, J.; Joy, M.; Storey, R.; Greig, H.; Hay, J.; James, T.;
Beech, M.; Ozane, R.; Meredith, A.; Boothroyd, I. 2009: Stream habitat assessment protocols
for wadeable rivers and streams of New Zealand. University of Canterbury, Christchurch.
http://www.cawthron.org.nz/coastal-freshwater-resources/downloads/stream-habitat-
assessment-protocols.pdf
Weber, C.I. 1973: Biological field and laboratory methods for measuring the quality of surface waters
and effluents. U.S. Environmental Protection Agency Report 670 / 4 / 73 / 001.
DOCDM-766000 Freshwater ecology: quantitative periphyton biomass sampling methods v1.0 15
Appendix A
The following Department of Conservation documents are referred to in this method:
docdm-769146 Freshwater ecology: periphyton rapid assessment monitoring in streams—
method 1 (RAM-1)
docdm-769150 Freshwater ecology: periphyton rapid assessment monitoring in streams—
method 2 (RAM-2)
docdm-146272 Standard inventory and monitoring project plan
docdm-761873 Stream habitat assessment field sheet