Document Number 80978 PIS 1-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Shown with Epson TM T88V printer
Document Number 80978 PIS 2-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Shown Fully Retracted Shown Fully Extended General Features
The assembly supports a Zebra Motorola Symbol DS9208 Bar Code Scanner and allows full function of the scanner’s integral five position indexed tilt feature.
The height of the scanner mounting plate adjusts from 6 3/4" to 11 5/8” as measured from the counter top to the base of the scanner.
The height of the scanner mounting plate is easily adjusted and locked into any desired position with a three pointed hand knob located on the back of the stand. The knob is permanently retained with a lock nut.
The side to side position of the scanner mounting plate is easily adjusted to pan 90 degrees to the left or right side. The desired scanner side to side position is easily secured with a three pointed hand knob located on the underside of the top of the stand.
With the scanner mounting plate adjusted to its lowest position; the base of the scanner is placed just above the top rear of an Epson TM T88V printer. With the scanner mounting plate adjusted to its highest position; there is plenty of room to swing open the printer paper access door on the top of the Epson TM T88V printer.
The scanner mounting plate uses the same quarter turn, quick disconnect key feature as found on the bottom of the DS9208 scanner.
Document Number 80978 PIS 3-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
General Features Continued
The scanner mounting plate includes a small thumbscrew to provide a tool less method of securing the scanner to the mounting plate.
The rear of the scanner mounting plate includes a ¾” DIA cable path opening for routing the scanner connecting cable. The scanner height adjustment plate includes two tie points to secure the connecting cable to the plate.
The base plate can support the assembly in a standalone application and is also large enough to support the Epson TM T88V and other printers installed directly on top of the pallet with ample clearance to accommodate the large DB25 connector found on the rear of some models.
The base plate includes multiple low profile non slip domed feet to slightly raise the base plate above any liquid spillage on the counter top.
The stand can be configured in either forward or reverse configurations without tools.
Document Number 80978 PIS 4-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978 Installing the scanner on the scanner mounting plate
1. Verify that the scanner mounting plate is turned so that the “V arrow” indicator on the top of the mounting plate is facing to the right side of the stand. If it is not in this position; adjust the side to side locking position knob and turn the plate to bring it to this starting position.
2. If the scanner mounting plate is in the correct starting position as described in step one with the “V arrow” indicator facing towards the right; verify that the three pointed side to side locking position knob on the underside of the top of the stand is tight.
Document Number 80978 PIS 5-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978 Installing the scanner on the scanner mounting plate (continued)
3. Turn the scanner so that the front of the scanner is facing towards the right side of the scanner mounting plate in the same direction as the “V arrow” indicator on the top of the plate.
4. Align the center of the key in the top of the scanner mounting plate with the center of the key hole in the bottom of the scanner base and carefully guide the scanner base down onto the scanner mounting plate.
5. Grasp the scanner and carefully turn it one quarter turn or 90 degrees clock wise as viewed
from above; so that the front of the scanner aligns with the front edge of the scanner mounting plate. The key in the scanner mounting plate should engage the keyhole on the bottom of the scanner.
6. Gently tighten the thumbscrew on the bottom front of the scanner mounting stand until you feel a slight resistance as the end of the thumbscrew contacts the bottom of the scanner base; then gently tighten the thumbscrew one half turn more.
Document Number 80978 PIS 6-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Installing the scanner connecting cable
1. Route the RJ45 plug end of your scanner connecting cable up through the ¾” DIA cable path opening in the rear the scanner mounting plate and insert the plug into the jack on the back of the scanner.
2. Tilt the scanner to its fully forward position to create a small amount of slack cable behind the scanner; then secure the cable with small cable ties to the two tie points on the vertical section of the scanner mounting plate.
3. Connect the other end of the scanner connecting cable to your Host Interface.
Adjusting the left, right or center facing position of the scanner
1. Verify that the scanner locking thumbscrew is tight; then slightly loosen the three pointed side to side position locking knob on the underside of the height adjustment plate.
2. Gently turn the scanner and the mounting plate to the desired new position taking care that the connecting cable is also adjusted to conform to the new position.
3. Gently re-tighten the three pointed side to side locking position knob on the underside of the height adjustment plate to secure the new position.
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Document Number 80978 PIS 7-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Adjusting the height of the scanner of the scanner
1. Grasp the scanner height adjustment plate securely below the scanner and carefully loosen the three pointed height position locking knob on the back side of the stand.
2. Raise or lower the scanner height adjustment plate to the new desired position and then gently re-tighten the height position locking knob.
Stand shown in Forward configuration
Document Number 80978 PIS 8-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Changing the stand from Forward configuration to Reverse configuration
1. Remove the plastic retaining washer from the threaded shaft above the three pointed height position locking knob on the back side of the stand.
2. Grasp the scanner height adjustment plate securely below the scanner and carefully remove the three pointed height position locking knob from the threaded shaft.
3. Remove the height adjustment plate from its standard position above the base plate and re-install it on the rear side of the slotted section of the base plate by inserting the threaded shaft into the slot and aligning the bends on the sides of the height adjustment plate with the outside edges of the with the slot the slotted section of the base plate.
4. Reinstall three pointed height position locking knob and the plastic retaining washer onto the threaded shaft.
Document Number 80978 PIS 9-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978 Adjusting the tilt position of the scanner
1. The scanner forward or downward tilt position can be adjusted from the scanner standing straight up position at 90 degrees to three forward indexed positions with a maximum of 45 degrees of forward or downward tilt. The scanner rearward tilt position can be adjusted from standing straight up position at 90 degrees to one rearward or upward position of approximately 105 degrees.
2. Grasp the top of the scanner and gently move the position of the scanner forward or rearward as desired; each click being one locking position of the integral five position indexed tilt feature.
Document Number 80978 PIS 10-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Instructions for hand operation or to remove the scanner from the stand.
1. Remove any cable ties that would restrict the cable and prevent the scanner from be removed from the stand, adjust the slack cable so that it will feed through the cable path openings. If you intend to use the scanner regularly for hand operation; do not route the connecting cable through the cable paths openings and the cable will travel much more smoothly when the scanner is lifted.
2. Follow the instructions detailed in the sections “Installing the scanner” and “Adjusting the left or right facing position of the scanner”.
3. Verify that desired scanner operating position is set for either left, right or center facing, also verify that the three pointed side to side position locking knob on the underside of the height adjustment plate is tight.
4. Loosen the scanner locking thumbscrew on the front of the underside of the height adjustment
plate to disengage the locking feature.
5. Grasp the scanner and carefully turn it one quarter turn or 90 degrees counter clock wise as viewed from above. The key in the scanner mounting plate should disengage from the keyhole on the bottom of the scanner. Carefully lift the scanner.
Installation Examples
Retail Applications Forward Configuration – Scanner Facing Right Reverse Configuration
Document Number 80978 PIS 11-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978 Installation Examples
Double Wait Station – Scanners in Forward Configuration
Document Number 80978 PIS 12-of-12
[email protected] WWW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022
ALL PRODUCTS PATENT PENDING
Zebra Motorola Symbol DS9208 Bar Code Scanner Adjustable Counter Top Stand PN 80978
Other PQS mounting options; more on our website:
