D o o r C l o s e r s
1
DOOR CLOSERPhiladelphia Hardware Group, Inc. is presenting the fi nest ADVANTAGE® surface mounting door closers for your various application demands. There are• Multi-size door closer: 9000, 8000, 6000, 6000S (slim cover), 5000, 4400 series.• Standard size door closer: 4000, 3000, 2000 series.• Multi-size Delay Action door closer: 8000/DA, 6000/DA, 6000S/DA series.
GENERAL INFORMATIONANSI A156.4 – American National Standard for Door Controls-ClosersADVANTAGE® Grade 1 Door Closers are certifi ed by ANSI/BHMA A156.4.
ADVANTAGE® Grade 2 Door Closers are factory tested to meet or exceed ANSI Grade 2 required strength and performance.
UL ListedAll of ADVANTAGE® door closer series are UL listed, and conforms to Standards UL10C and UPC 7-2(1997).
Meet ADA requirementsADVANTAGE® door closer 9000, 8000, 6000, and 4400 series meet ANSI A117.1 requirements for ADA.Please note Door Closer with reduced opening force may not provide suffi cient power to close a door.
• Doorways shall have a clear opening of 32” minimum. Clear opening of doorways with swinging doors shall be measured from the face of door and stop with the door open 90°.
• Door closers shall be adjusted so that from the open position of 90° the time required to move the door to an open position of 12° shall be 5 seconds minimum.
• The maximum force for pushing open or pulling open doors other than fi re doors shall be as follows: 1. Interior hinged door: 5 lbs. 2. Exterior hinged door: 8.5 lbs. * 4400 series apply to interior hinged door only.
HandingAll ADVANTAGE® Door closers are non-handed that are suitable for left-opening or right-opening door.
All Weather Hydraulic Fluid used to ensure smooth operation under severe weather conditions.
Finish Stock available Aluminum (BHMA 689) for all model Duranodic (BHMA 695) for all model Gold (BHMA 696) for all model Satin Chrome (BHMA 652) for 8000 series
ACCESSORIESDrop Plate allows a door closer to be fi tted on narrow top rail or narrow top frame door. Most of the ADVANTAGE® door closers have different kinds of Drop Plates for installation requirements, see following pages in detail.
Hold Open Arm used when door is requiring for a clear opening doorways at 90˚ stop.* Should not be used on Fire door application.
Parallel Rigid Cush Arm is a heavy duty arm with an auxiliary stop in soffi t shoe to stop the door opening at a specifi c point. Apply to door where wall or fl oor stops are not appropriate. Parallel arm mounting application only.
Parallel Rigid Cush and Stop Arm is a heavy duty hold open arm featured with a plunger hold open to engage or disengage hold open by a handle on the arm. Parallel arm mounting application only.* Should not be used on Fire door application.
Aluminum Duro (Duranodic) Gold
Opening Cycle
Parallel Arm Installation
closer mounts on opposite to hinge (pull) side of door
Top JambInstallationcloser mounts
on frame face on opposite to hinge (pull) side of door
2
DOOR CLOSER
Regular ArmInstallationcloser mounts
on hinge (pull) side of door
DOOR CLOSER APPLICATION
There are three basic methods of mounting surface door closers to the door and frame including regular arm, parallel arm and top jamb mounts. All ADVANTAGE® door closers are supplied standard with a tri-pack for mounting any of three types applications.
Top Jamb (Push side)More power-effi cient than the parallel arm applicationApplying to a closer with narrow top rail on a door.The closer body is mounted to the frame face above the door, opposite the door hinge side. The forearm is then mounted to the top rail of the door.
Parallel Arm (Push side)Least power-effi cient applicationThe closer body is mounted on the top rail of the door, opposite the hinge side of the door.The forearm is mounted by a parallel arm bracket to the underside of the frame.The arm is parallel to the door, which makes it less likely to be damaged.* Top reveal should have enough space for using this application.
Regular Arm (Pull side)Most power-effi cient application The Closer body is mounted on the hinge side of the door top rail.The forearm is mounted to the frame face by a mounting shoe.Arm projects at approximately a 90° angle away from the door.
CLOSER ADJUSTMENT
ADVANTAGE® Door closers have hex wrench controlling valves for adjusting Closing speed and latch speed.Multi-size door closers have a nut for spring power adjustment, and additional valve for Backcheck.Delay Action control valve available with Delay Action model.
Use adjustable wrench to rotate spindle 45° counter-clockwise for right hand door or clockwise for left hand door. Place main arm on spindle so that the “R” (Right hand door) or “L” (Left hand door) lines up with the spindle fl at. Secure main arm and spindle by tightening spindle bolt.
Left hand door-LHRight hand reverse-RHR
Left hand door-LHRight hand reverse-RHR
Left hand door-LHRight hand reverse-RHR
Right hand door-RHLeft hand reverse-LHR
Right hand door-RHLeft hand reverse-LHR
Right hand door-RHLeft hand reverse-LHR
3
DOOR CLOSERClosing speed & Latching speed are dual valve control for door closing speed. Closing speed is the speed of door closing from full opening to approximately 10˚~5˚ of door closed position.Latching speed is the speed from approximately 10˚~5˚ door opening to door closed posi-tion. Slow latch speed provides less door closing noise.
Backcheck slows down the door opening at approximately 70˚ in order to prevent damage to building and door frames.The backcheck control valve provides a 20˚ adjustment (70˚ ~ 90˚) to set the optimum back-check start point. * Multi-size door closers are standard with Backcheck function.
Delay Action is the 3rd control for closing speed ad-justment.It effective from full opening to approximately 70˚, and provides a slow closing speed. The closing time between 180˚ to 70˚ is at least 20seconds, and easily adjustable up to 1minutes. Closer with Delay Action provides suffi cient time that allows people or the elderly to get through the door before it starts to close.
Multi-size Spring adjustmentMulti-size door closers are able to adjust the spring power to meet the power needs of the door.Spring power of the closer can be increased by turning the power adjustment nut clockwise, vice versa.
* Multi-size door closers provide the spring power required to fi t your door size and application.
1
2
3
4
5
6
28”
36”
42”
48”
54”
60”
N/A
N/A
30”
36”
42”
48”
N/A
N/A
36”
42”
48”
54”
N/A
30”
36”
42”
48”
54”
N/A
N/A
30”
36”
42”
48”
33 ~ 66
66 ~ 99
99 ~ 143
143 ~ 187
187 ~ 264
264 ~ 330
Recommended Maximum Door SizeCloser Size (Spring Power)
Closer
Size
Door Weight
(Lbs.)
Regular & Top Jamb Parallel Arm
Exterior Swing-in(Pull Side)
Exterior Swing-out (Push Side
Interior Swing-out(Push side)
Exterior Swing-out(Push side)
Interior
4
9000 SERIESUL
LISTED
R
ANSI GRADE 1ANSI/BHMA A156.4-2000Series 2000, PT1Exceeds 1,500,000 cycles with Backcheck
UL10C Positive Pressure Rated. Conforms to UBC 7-2 (1997). (Uniform Building Code Standard)
Comply with ANSI A117.1
ANSI GRADE 125-Year Warranty
Model9000 Adjustable power size 1-6 with Back Check
Applications• Heavy Duty Commercial model ideal for high traffi c door such as schools, hospitals, and public institutions• Same mounting hole pattern as CAL-ROYAL 900 (CTC 11-1/8” x 1-1/8”), ideal for renovations• Tri-packed for all type applications
Features• Multi-size spring adjustable power size 1-6 Factory preset size 3• Meet ADA• Standard with adjustable Backcheck
Optional FuctionsAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed, and Back-checkStaked valve for power adjustmentStandard arm and parallel bracket included for different mounting demandSelf-tapping wood screws and machine screwsAluminum, Duronotic, and Gold
Material
CoverValves
Arm & BracketsScrewsFinishes
• Hold Open Arm (9001)• Parallel Rigid Cush Arm (9002)• Parallel Rigid Cush and Stop Arm (9003)• Extended forearm (9004)• Sex-bolts (Metal door mounting)
* Special order from the factory• Delay Action• Metal cover• Plated Finish: US3, US26, US26D
Series 9000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from Door
Size11-7/8”11-1/8”1-1/8”
2”2-3/8” End View Front View
9001Hold-open ArmStand for pull side & top jamb Use with PA bracket for parallel arm mount
9002Parallel RigidCush ArmAuxiliary Stop in soffi t shoe
9003Parallel Rigid Cush and Stop ArmHand control plunger stop in soffi t shoe
9004Extended ForearmFor Top Jamb with reveal greater than 4” and up to 8”
90CStandard Full Plastic Cover
1348Sex-bolt with screwFor 1-3/4” standard Door Thick
PAB01Parallel Bracketfor Hold Open Arm mountingcan also use for regular parallel arm application
Product Specifi cation
Technical Dimensions
Accessories
5
8000 SERIESUL
LISTED
R
ANSI GRADE 1ANSI/BHMA A156.4-2000Series 2000, PT1Exceeds 1,500,000 cycles with Backcheck
UL10C Positive Pressure Rated. Conforms to UBC 7-2 (1997). (Uniform Building Code Standard)
Comply with ANSI A117.1
ANSI GRADE 125-Year Warranty
Model8000 Adjustable power size 1-6 with Back Check8000/DA Adjustable power size 1-6 with Delay Action
Applications• Extra Heavy Duty Commercial model ideal for high traffi c door Versatile for new constructions, such as schools, hospitals, and public institutions• Same mounting hole pattern as LCN4041, ideal for renovations• Tri-packed for all type applications
Features• Multi-size spring adjustable power size 1-6 Factory preset size 3• Meet ADA
Optional Fuctions
Accessories
Heavy Duty Cast Iron body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed,and Back-check cushionDelayed Action valve – Optional (Model: 8000DA)Staked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws and machine screwsAluminum, Duronotic, Gold, and US26D-Satin Chrome
Material
CoverValves
Arm & BracketsScrewsFinishes
Wide choice of options for different applications• Hold Open Arm (8001)• Parallel Rigid Cush Arm (8002)• Parallel Rigid Cush and Stop Arm (8003)• Extended forearm (8004)• Drop Plate (see Accessories)• Sex-bolts (Metal door mounting)
* Special order from the factory• Metal cover• Plated Finish: US3, US26
Series 8000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from Door
Size11”5”1”
2-3/4”2” End View
Front View
8001Hold-open ArmStand for pull side & top jamb Use with PA bracket for parallel arm mount
8002Parallel RigidCush ArmAuxiliary Stop in soffi t shoe
8003Parallel Rigid Cush and Stop ArmHand control plunger stop in soffi t shoe
80CStandard Full Plastic Cover
1348Sex-bolt with screw
8004Extended ForearmFor Top Jamb with reveal between 2-5/8” to 4-13/16”
Product Specifi cation
Technical Dimensions 80DP-ST Size: 12-1/4 x 3-9/16”Drop Plate – Pull SideHinge side mount when top rail is less than 3-3/4”Plate require 2” minimum top rail80DP-TJ Size: 12-1/4 x 3-9/16”Drop Plate – Top JambUse when frame face is less than 3 1/2”Use 8004 forearm if top reveal exceeds 2-9/16”80DP-TG Size: 12-1/4 x 3-9/16”Drop Plate – Top Jamb with fl ush ceilingTop of head frame face in fl ush ceiling conditionPlate requires 1-3/4” minimum frame faceUse 8004 forearm if top reveal exceeds 2-9/16”80DP-PA Size: 12-1/4 x 5”Drop Plate – Parallel ArmUse when top rail is less than 5-1/2”, measured from the stopPlate requires at least 2-1/2” top rail
PAB01Parallel Bracketfor Hold Open Arm mountingcan also use for regular parallel arm application
6
6000, 6000S SERIESUL
LISTED
R
ANSI GRADE 1ANSI/BHMA A156.4-2000Series 2000, PT1Exceeds 1,500,000 cycles with Backcheck
UL10C Positive Pressure Rated. Conforms to UBC 7-2 (1997). (Uniform Building Code Standard)
Comply with ANSI A117.1
ANSI GRADE 125-Year Warranty
Optional Fuctions
Accessories
Aluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – 6000 seriesTriple valve control for Closing speed, Latching speed, and Back-checkDelayed Action valve – Optional (Model: 6000/DA, 6000S/DA) Staked valve for power adjustmentStandard arm and parallel bracket included for different mounting demandSelf-tapping wood screws and machine screwsAluminum, Duronotic, and Gold
Material
CoverValves
Arm & BracketsScrewsFinishes
Wide choice of options for different applications• Hold Open Arm (6001)• Parallel Rigid Cush Arm (6002)• Parallel Rigid Cush and Stop Arm (6003)• Extended forearm (6004)• Drop Plate (see Accessories)• Sex-bolts (Metal door mounting)
* Special order from the factory• Metal cover (Full Cover only)• Plated Finish: US3, US26, US26D
Series 6000, 6000SA. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from Door
Size12-3/4”
12”3/4”
1-1/4”2-1/8” End View Front View
6001Hold-open ArmStand for pull side & top jamb Use with PA bracket for parallel arm mount
60C-FStandard Full Plastic Cover
1348Sex-bolt with screw
6002Parallel RigidCush ArmAuxiliary Stop in soffi t shoe
6003Parallel Rigid Cush and Stop ArmHand control plunger stop in soffi t shoe
6004Extended ForearmFor Top Jamb with reveal greater than 4” and up to 8”
Product Specifi cation
Technical Dimensions 60DP-ST Size: 13-1/8 x 3-1/4”Drop Plate – Pull Side , or Concealed Door HolderUse for hinge side mountUpside-down to mount where concealed door holder prevents normal door closer mountingPlate require 2-7/16” minimum top rail60DP-TJ Size: 13-1/8 x 3-5/8”Drop Plate – Top JambApply to low ceiling clearance between 1-1/2” ~ 1-3/4”60DP-PAS Size: 13-1/8 x 3-5/8”Drop Plate – Parallel ArmPlate require 2-7/8” minimum top railCross reference: NORTON #314860DP-PA Size: 13-1/8 x 5”Drop Plate – Parallel arm mountUsed to mount a closer on a top rail as narrow as 3” in height
Model6000, 6000S Adjustable power size 1-6 with Back Check6000/DA, 6000S/DA Adjustable power size 1-6 with Back Check and Delay Action
Applications• Heavy Duty Commercial model ideal for high traffi c door Versatile for new constructions, such as schools, hospitals, and public institutions• Same mounting hole pattern as NORTON 8000 CTC 12” x 3/4”, ideal for renovations• Tri-packed for all type applications
Features• New upgraded design from year 2009 Multi-size spring adjustable power size 1-6, Factory preset size 3• Meet ADA • Standard with adjustable Backcheck
PAB01Parallel Bracketfor Hold Open Arm mounting can also use for regular parallel arm application
60C-SStandard Slim Plastic Cover
Full Cover
Slim Cover
4001Hold-open ArmStand for pull side and top jamb Use with PA bracket for parallel arm mount
7
40DP-TJ Size: 9-3/4” x 2-9/16”Drop Plate –Top Jamb low ceiling clearanceFor use when ceiling clearance is between 1-3/4” and 2-5/8”Cross reference: NORTON #168740DP-PA Size: 9-3/4” x 3-1/2”Drop Plate –Parallel arm mount Used to mount a closer on a top rail as nar-row as 2-5/8” in height
5000, 4400 SERIES ANSI GRADE 125-Year Warranty
Optional FuctionsAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed, and Back-checkStaked valve for power adjustmentStandard arm and parallel bracket included for different mounting demandSelf-tapping wood screws and machine screwsAluminum, Duronotic, and Gold
Material
CoverValves
Arm & BracketsScrewsFinishes
• Hold Open Arm (4001)• Drop Plate (see Accessories)• Sex-bolts (Metal door mounting)
Series 5000, 4400A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from Door
9-3/4”9-1/16”
3/4”1-3/4”2-7/8”
Size9-3/4”9-1/16”
3/4”1-3/4”2-7/8” End View Front View
Product Specifi cation
Technical Dimensions
40CStandard Full Plastic Cover
1348Sex-bolt with screwFor 1-3/4” standard Door Thick
Accessories
Model5000 Adjustable power size 3-6 with Back Check4400 Adjustable power size 1-4 with Back Check
Applications• Heavy Duty Commercial model, ideal for high traffi c door Versatile for new constructions, such as schools, hospitals, and public institutions• Universal mounting hole pattern Size 4: CTC 9-1/16” x 3/4”• Tri-packed for all type applications
Features• Multi-size spring adjustable power size 3-6, factory preset size 4 Multi-size spring adjustable power size 1-4, factory preset size 3• 4400 meets ADA, Barrier Free interior• Standard with adjustable Backcheck
ULLISTED
R
ANSI GRADE 1ANSI/BHMA A156.4-2000Series 2000, PT1Exceeds 1,500,000 cycles with Backcheck
UL10C Positive Pressure Rated. Conforms to UBC 7-2 (1997). (Uniform Building Code Standard)
4400 SeriesComply with ANSI A117.1
PAB02Parallel Bracketfor Hold Open Arm mounting can also use for regular parallel arm application
4001Hold-open ArmFor 4000 SeriesPull side and top jamb Use with PA bracket for parallel arm mount
8
4000, 3000, 2000 SERIES ANSI GRADE 210-Year Warranty
Model4000 Standard power size 43000 Standard power size 32000 Standard power size 2
Applications• Medium and Light Duty model Medium Duty 4000 Light Duty 3000, 2000• Universal mounting hole pattern Size 4: CTC 9-1/16” x 3/4” Size 3: CTC 8-3/16” x 3/4” Size 2: CTC 6-5/8” x 3/4”
Optional Fuctions
Accessories
Aluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionTriple valve control for Closing speed, Latching speed, and Back-checkStaked valve for power adjustmentStandard arm and parallel bracket included for different mounting demandWood screws and machine screwsAluminum, Duronotic, and Gold
Material
Valves
Arm & BracketsScrewsFinishes
• Hold Open Arm (3001, 4001)• Drop Plate (See Accessories)• Sex-bolts (Metal door mounting)• Full plastic cover, available for 4000 series only (40C)
Product Specifi cation
40DP-TJ For 4000 Series Size: 9-3/4” x 2-9/16”Drop Plate –Top Jamb low ceiling clearanceFor use When ceiling clearance is between 1-3/4” and 2-5/8” 40DP-PA For 4000 Series Size: 9-3/4” x 3-1/2”Drop Plate –Parallel arm mount Used to mount a closer on a top rail as narrow as 2-5/8” in height 30DP-PA For 3000 Series Size: 3-1/2” x 8-3/4”Drop Plate – Parallel arm mount20DP-PA For 2000 Series Size: 3-1/2” x 7-5/16”Drop Plate – Parallel arm mount
3001Hold-open ArmFor 3000 SeriesPull side and top jambUse with PA bracket for parallel arm mount
40C For 4000 SeriesStandard Full Plastic Cover
1348Sex-bolt with screwFor 1-3/4” standard Door Thick
ULLISTED
R
GRADE 2Factory tested to meet ANSI Grade 2 durability
UL10C Positive Pressure Rated. Conforms to UBC 7-2 (1997). (Uniform Building Code Standard)
Series 4000, 3000, 2000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from Door
9-3/4”9-1/16”
3/4”1-3/4”2-7/8”
Size8-3/4”8-3/16”
3/4”1-3/4”2-7/8”
7-5/16”6-5/8”3/4”
1-3/4”2-5/8” End View Front View
Technical Dimensions
PAB02Parallel Bracketfor Hold Open Arm mounting can also use for regular parallel arm application
9
ORDER INFORMATIONSeries
9000
8000
8000/DA
6000
6000S
6000/DA
6000S/DA
5000
4400
4000
3000
2000
Power Size
Adjustable No. 1-6
Adjustable No. 1-6
Adjustable No. 1-6
Adjustable No. 1-6
Adjustable No. 1-6
Adjustable No. 1-6
Adjustable No. 1-6
Adjustable No. 3-6
Adjustable No. 1-4
No. 4
No. 3
No. 2
Duty
Heavy
Extra Heavy
Extra Heavy
Heavy
Heavy
Heavy
Heavy
Heavy
Heavy
Medium
Light
Light
BackCheck
DelayAction
Hold Open with Hold Open Arm
Parallel Rigid Cush Arm
Cush &Stop Arm
DropPlate
Sex-Bolt
PlasticCover
MetalCover
Function Availability AccessoriesProduct Availabilities
Adjustable Power with Back-Check (BC)
Adjustable Power with Back-Check (BC) and Delay Action (DA)
Fixed Power Size
Adjustable Power with Delay Action (DA)
9000
8000
6000
6000S (Slim Cover)
5000
4400
6000/DA
6000S/DA (Slim Cover)
8000/DA
4000
3000
2000
ADVANTAGE® Door Closers
No. 1-6 BC
No. 1-6 BC
No. 1-6 BC
No. 1-6 BC
No. 3-6 BC
No. 1-4 BC
No. 1-6 BC DA
No. 1-6 BC DA
No. 1-6 DA
No. 4
No. 3
No. 2
Power Size
609912
608812
606712
606732
605112
604412
606742
606752
608842
604012
603302
602202
Gold
609911
608811
606711
606731
605111
604411
606741
606751
608841
604011
603301
602201
Product CodeDuro
609910
608810
606710
606730
605110
604410
606740
606750
608840
604010
603300
602200
Aluminum
● Standard or optional ● Special order from the factory, allow for longer lead time. Please call for more information
10
CROSS REFERENCE9000
1 – 6
11-1/8” x 1-1/8”
N900-PBF
● DC6200
● DC3200
PR74BC
● TC600
● 9000
● 1431
D3550/D3551
900BC
1900
● 700
8000
1 – 6
5” x 2-1/4” x 1”
CR441
● DC8000
PR90
416
● 8916
● SC70
C900
TC4300
5100
44CI
4040
● 7500
7100
● 281
D4550/D4551
900
4400
6000
1 – 6
12” x ¾”
5016N
CR801
● DC6200
● DC3200
316
8616
SC81
C7500
TC500
● 5200
Size 2-5
5000
8501
5300
1331
800
3501
YMDC2501
6000S
1 – 6
12” x ¾”
CR801S
SC80
C7300
TC400
8301
3301
5000/4400
3 – 6/1 – 4
9-1/16” x ¾”
936N/DC214
300
● PR80/PR82BF
PR80 Size 2-5
116
● 7400
● SC60/SC61
SC60 Size 2-5
● C5025/C5014
C5025 Size 2-5
TC200
5300
8050
● 1260
Size 1-5
1600
1100/3100
1130
● D1650/D1651
D1650 Size 2-5
● BF900
814BC
● 800/800BF
800 Size 2-5
600
50
YMDC1101
4000
4
9-1/16” x ¾”
DC204
740
440-FP
4604
DC54
Size 4
100
● 7304
● 7204
SC64
SC94
TC204
5400
854
● 754
654
1100/3100
1134
534
● 604
500
● 5104
3000
3
8-3/16” x ¾”
● DC203
730
430-P
● 4603
DC53
Size 3
100
● 7303
● 7203
● SC93
TC2203
● 5400
853
753
653
533
● 603
● 5103
2000
2
6-5/8” x ¾”
● 720
● 420-P
● 4602
● DC52
Size 2
100
● TC302
● TC2202
● 5400
● 852
● 752
● 652
● 532
602
● 5102
ADVANTAGE®
Spring Power Size
CTC Hole Pattern
ARROW
CAL-ROYAL
CORBIN/
RUSSWIN
CRL
DESIGN
HARDWARE
DORMA
FALCON
DOR-O-MATIC
GENERAL LOCK
GLOBAL
DOOR CONTROL
HAGER
INTERNATIONAL
DOOR CLOSER
LCN
NORTON
PDQ
Manufacturing
SARGENT
STANLEY
S.PARKER
TAYMOR
TELL
YALE
● The same mounting hole pattern with similar application ● Different mounting hole pattern in the same power sizeAll brand names & trademarks used are properties of their respective owners
Copyright ©2010 Philadelphia Hardware Group, Inc. All rights reserved.
Philadelphia Hardware Group, Inc.
DISTRIBUTION BY:
SAN DIEGO DISTRIBUTION CENTER (Home Offi ce)6590 Top Gun Street San Diego, CA 92121Tel: (858) 642-0450 Fax: (858) 642-0454Toll Free Tel: 1-800-545-2309 Toll Free Fax: 1-800-828-0988philihardware.com
CHICAGO DISTRIBUTION CENTER3687 Darlene Court Aurora, IL 60504Tel: (630) 692-0316 Fax: (630) 692-0320Toll Free Tel: 1-800-406-5138
SEATTLE DISTRIBUTION CENTER3705 166th Place N.E. Arlington, WA 98223Tel: (360) 659-7680 Fax: (360) 659-7401Toll Free Tel: 1-800-333-5156Toll Free Fax: 1-800-596-5156
Group Inc.
DISTRIBUTION BY: