Door Pulls Pulls & Glass Door Hardware Hinges, Accessories ... ket’s first flush pulls with spring...

Door Pulls & Glass Door Hardware

North American Manual

North American Manual About FSB

Designer Series

Lockset Program

Lever, Knob & Trim Designs

Sliding Door Hardware


Hinges, Accessories

Window Handles

Brass & Bronze Products

Door Closers

METRIC Bath Accessories

Components

Installation Instructions

Specialty Applications


About FSB

New Products

Materials and Finishes

Door Pulls

Technical Informations

Overview

FSB’s Threaded Insert Fixing Method

FSB Clamping Rose Fastening

Fixing Methods Pull Handles

Glass Door Hardware

Overview

Glass Door Trim and Strike Boxes

European Profile Cylinder (PZ)

Hinges for Glass Doors

Fixed Knobs for Glass Doors

Flush Pulls and Pulls for Glass Doors

Sliding Door Handle and Door Holder

Sliding Door Gears

4

5

6

8

10

62

63

65

73

74

79

82

88

90

92

93

About FSB

4

1881

FSB was established in 1881.Together with a modest work -force, company founder FranzSchneider produced antique-style brass cabinet fittings.

1920s

In the early 1920s, the first doorand window fittings appeared inthe FSB production program.The design of these years echoedthe modernism of the Bauhausera. Silver metal com po nentswere combined with black com-posite features.

1990s

Inspired by an international design workshop held in Brakelin 1986, FSB began engagingthe market with contemporarydesigns in an initiative dubbed“Tour d’Europe.” Throughoutthis initative FSB created designsuites with such renouned designers as Philippe Starck,Jasper Morrison, Richard Rogersand many others.

For the past two decades, FSBhas continued to work with Archi-tects and Designers to createhandles – each with their ownpersonality.

1950s

Beginning with in-house designerJohannes Potente in the 1950s,FSB created the first handleswhich exemplify minimalism,modernism and ergonomics. FSB is still known for the use ofthese design principles today.

Four of Potente’s lever de-signs have been included in thepermanent collection of the Mu-seum of Modern Art (MoMA).

2000s

FSB introduced a limited rangeof levers supplied in completelocksets to the Amercian designcommunity. The first catalogwas approximately 80 pages.Two later catalogs increasedFSB’s North American offeringto nearly 100 lever designs.

In 2007, FSB expanded theNorth American distributioncenter, moving it to Madison,CT, where the majority of prod-ucts are stocked in natural anodized aluminum and satinstainless steel. Stock items canbe shipped in 48 hours. All non-stock items can be shippedwithin two to eight weeks regard -less of the product type, finishor project size.

2008

FSB dramatically increased itsproduct range for North Amer -ica, and issued an expanded catalog of more than 500 pages.

This brochure gives an intro-duction to the breadth and styleof our entire product offering,which can be found in ourNorth American Manual. To request a manual, or view moredetailed information, go towww.fsbna.com.

New Products

5

Hinges

FSB introduces a new line ofhinges unique in their construc-tion, finish and performance.

FSB stainless steel two-knuckleand three-knuckle hinges utilizecarbon steel and oil-impregnatedsintered bronze bearings to min-imize friction, thereby reducingwear and maintenance. FSBstainless steel hinges may besupplied to simulate nearly all of our standard finishes, and aresupplied with low-profile button-tip finials, giving the protrudinghinge barrel an elegant, cleanlook.

Sliding Door Hardware

Building owners are demandingmore efficient use of space.Consequently, architects and designers are utilizing manymore sliding and pocket doors.

In recognition of this trendFSB has developed an entirerange of flush mounted trim forpassage, privacy and entry applications. We demonstrateour penchant for divising aesthetically pleasing technicalsolutions by offering the mar-ket’s first flush pulls with springloaded covers, as picturedabove.

A complete overview of theseproducts is provided in the“Sliding Door Hardware” section.

Bronze

There is an increase in an “oldmeets new aesthetic” in whichdesigners are combining tradi-tional finishes with more mini-mal and modern design. Foryears, FSB has offered ten ofour best selling handles in solidbrass, either polished or oxidiz edto give them varying degrees ofantiquing to suit the designers’needs.

FSB now introduces Bronzeas a new material for our leverhandles and accessories. Thespecial appeal of bronze is thepatina that develops on its sur-face. In the course of daily use,polished bronze parts darkennaturally, becoming more distin-guished with time.

We have created a completesection titled “Brass and BronzeProducts” to cover all the pro ducts we offer in these two exceptional base materials. We offer eight bronze handles andten brass handles for projectsthat may benefit from this “oldmeets new” aesthetic. All brassand bronze products can be oxidized to varying degrees ofdarkness, depending on “themood” a designer would like tocreate.

Glass Door Hardware

Creating more open spaces has become a cornerstone ofmodern architecture. Utilizinglarge pieces of glass, whetherfor windows, doors, or walls, facilitates this objective.

FSB has broadened its glassdoor program to include locksand hinges for swinging glassdoors as well as exposed rollinggears for sliding glass doors.These products can be found inthe section “Door Pulls andGlass Door Hardware”.

Materials and Finishes

6

Most of our hardware is availablein aluminum and stainless steelas a base material.

We offer up to 6 finishes oncertain base materials with 19finishes overall. Aluminum is either anodized or powder coated.

To confirm a particular finish isavailable for a specific product,consult each page.

On overview pages, and all pagesthroughout this catalog, only thebase material is indicated. Itcan be assumed that all finishesshown to the right of the basematerial below are availablewhenever a base material is indicated for a product.

If, by exception, a specific finishis not available for a given basematerial, it will be stated by thedetail page for that product.

Base Material

Aluminum Anodized

Aluminum Powder Coated

Stainless Steel

Bronze

Brass

FSB Finish (BHMA Code)

0105 Natural Color (628) 0205 German Silver (Champagne) Color 0305 Brass Color (688) 0405 Bronze Color (709) 0704 Dark Bronze Color (710)1005 AluGrey

8120 Black (693) 8220 White (714E) 8320 Red

6204 Satin (630) 6205 Mirror Polished (629) 6206 Matte

7305 Polished Oil Rubbed 7615 Artificially Aged and Oil Rubbed (615) 7625 Patinated and Oil Rubbed (613)

4205 Polished Lacquered (605) 4305 Polished Oil Rubbed (721) 4694 Oxidized Lacquered 4404 Oxidized Oil Rubbed (607)

Aluminum Stainless Steel

7

Bronze

0105 Aluminum Natural Color Anodized

6204 Satin Stainless Steel

6205 Mirror Polished Stainless Steel

6206 Matte Stainless Steel

7305 Bronze Polished Oil Rubbed

7615 Bronze Artificially Aged and Oil Rubbed

7625 Bronze Patinated and Oil Rubbed

4205 Brass Polished Lacquered

4305 Brass Polished Oil Rubbed

4694 Oxidized Brass Lacquered

4404 Oxidized Brass Oil Rubbed

0205 Aluminum German Silver (Champagne) Color Anodized

0305 Aluminum Brass Color Anodized

0405 Aluminum Bronze Color Anodized

0704 Aluminum Dark Bronze Color Anodized

8220 Aluminum Powder Coated White approx. RAL 9003

8320 Aluminum Powder Coated Red approx. RAL 3002

8120 Aluminum Powder Coated Black approx. RAL 9004

1005 AluGrey

Brass

Back-to-Back Fixing Through-Bolted Fixing Concealed Fixing With Expansion Plug (for Solid Doors)

Materials, Fixing Options, Safety Clearance

8

Over the past decade, FSB hasadded a fully-fledged alternativeto its traditional tubular pull -handle range with a comprehen -sive collection of oval designs.Both sets of designs can befixed in a wide variety of ways.The traditional range of push/pullpad handles and profiles withbrackets has also been furtherdeveloped.

Materials

In principle, FSB supplies itsentire pull-handle range in eitheraluminum, stainless steel, brassand bronze, with stainless steelbeing particularly recommendedfor heavy-duty applications. Aluminum surfaces can easilyget blemished in such circum-stances, though this “agingprocess” in no way impairs thefunctioning of the handle. Owingto their tendency to corrode,brass and bronze pulls are onlyoffered with an oil rubbed finish.When ordering non-oxidizedproduct that has not been lac-quered, it takes several yearsbefore a natural brown protectivepatina forms on brass or bronzehandles.

Fixing Scenarios

Pulls can be either face orthrough fixed to doors made ofthe most diverse of materials. In the case of through-boltedfixing, either a pair of pulls or asingle handle can be fitted.

FSB offers the four fixing options below: · back-to-back fixing, · through-bolted fixing, · concealed fixing with

expansion plug (for solid doors), · concealed fixing with

drop clamp (for hollow doors). This section has clear identify-ing symbols that can be foundon all relevant product pages.(Examples show fixing for tubular pulls).

Regarding the issue of concealedversus through-bolted fixing,FSB wishes to point out that, onaccount of the compression ringtechnique deployed by FSB, con-cealed fixing is both aestheticallypleasing and sufficiently durableas a rule. This needs to be qual-ified, how ever, in the case ofheavy-duty applications, (i. e. inschools, office blocks and otherpublic institutions): here, weemphatically recommendthrough-bolt fixing, which en-sures that the trim remains fitfor use even after years of heavytreatment, since the forces in-volved are absorbed on bothsides of the door.

Safety Clearance (S)

When fitting a handle to theclosing face of a door, a safetyclearance needs to be allowedfor between the handle and theedge of the door and the jamb.The assembly scenario is mademore readily comprehensible bythe following sketch.

Ideally, safety clearances asre commended by FSB shouldbe adhered to. Nevertheless,con ditions at the point of as sem-bly are crucial. It is particularlyadvisable to make use of offsetpulls purpose-designed by FSBfor especially narrow stiles, whichsets the handle sufficiently faraway from the edge.

S

Concealed Fixing With Drop Clamp (for Hollow Doors)

FSB has developed over the pastdecade an alternative to tradi-tional pulls of circular cross-section. Adopting the formula“diagonal + oval = ideal gripping”identified by FSB reduces theamount of effort required to takehold of and operate the handleson entrance doors.

The oval styling offers the mar-ket a new gripping quality foreye and hand which FSB hashad copyright protected. Theexperience FSB has amassednow allows it to supply almostall its traditional styles both ascircular pulls and as optimized-grip oval variants.

A new flattened oval pull seriesairily and elegantly underpinsarchitectural solutions.

Pull Handles Oval Series

European Handing for Pulls and Glass Door Locks

Pull Handles Round Series

9

The proven FSB range of tubularpulls has profited from the burstof innovation in the sphere ofoval designs. New shapes andbrackets have been added.

This is particularly true of thelightweight pull series in 20 mmtubular material, for which anew design-conscious bracketfixture has been developed thatFSB has likewise had utility anddesign patented. Hence, thislightweight pull-handle series inits familiar “straight, rectangular,triangular and crescent” stylescan continue its victorious cam-paign against the tradi tional“heavyweights”.

The hand grips oval

Custom lengths can be providedfor several of our round and ovalpulls. Where it is possible weprovide a sheet to be populatedwith the desired dimensions.

If no such sheet exists, theability to provide custom lengthsis indicated with a “99” follow-ing the pull handle number.When ordering, please providethe overal length desire.

Explanation:

The European (German DIN)specifications “European righthand (r.h.)” respective “Euro-pean left hand (l.h.)” refer tothe positioning of the hinges onthe opening face of the door.

inside

outside

inside

outside

inside

outside

inside

outside

European (DIN) left hand inward opening

European (DIN) right hand inward opening

European (DIN) left hand outward opening

European (DIN) right hand outward opening

Overview

10

Page 12

Page 19 Page 19 Page 20 Page 21 Page 22

Page 22 Page 23 Page 24 Page 24 Page 25 Page 26 Page 27



6501

Page 13

6504

Page 53

6510

Page 15

6514

Page 16

6526

Page 18

6533

Page 18

6534 6535 6536 6537 6538 6540

6541 6542 6543 6546 6599 6602 6605

6610 6611 6612 6613 6615 6616 6620

6621 6630 6635 6636 6642 6643 6650

Page 14

6506 xx

Page 14

6507 xx

11

Page 41 Page 42

6652 6653

Base Material

Aluminum

Stainless Steel

Bronze

Brass

Alu + Color

Plastic Black

Page 43

6655

Page 44

6662

Page 45

6669

Page 46

6674

Page 47

6675

Page 52

6677, 6688

Page 48

6679

Page 34

6681

Page 50

6682

Page 49

6683

Page 51

6685

Page 55

6108

Page 56

6112

Page 56

6113

Page 57

6181

Page 57

6184

Page 58

6254

Page 58

6268

Page 59

2160

Page 59

3601

Page 60

3603

Page 60

3617

Page 61

6628

Page 61

6629

Page 61

5325

Stock Items (in Natural Color Aluminum and Satin Stainless Steel)


12

350 390

35

Ø 20

65

6501 Ø 20 mm

Aluminum Stainless Steel Brass

Safety clearance 49 mm Fixing M8

The “heavyweights” of the long-running standard program arejuxtaposed with a “lighter thanair” series of pull handles(20 mm) in several shapes onplain brackets (25 mm). For detailed information onfixing, please turn to page 66.

Back-to-Back Fixing Through-Bolted Fixing Concealed Fixing With Expansion Plug

Concealed Fixing With Drop Clamp


13

350

35

Ø 20

65

92

R 213

6504 Ø 20 mm



For detailed information onfixing, please turn to page 66.




14

45

Ø 35

220

1000

95

R 60

R 60

45

Ø 35

474

1000

95

R 60

R 60

6506 xx xx = 65 (r.h.) or 75 (l.h.) Ø 35 mm

Aluminum Stainless Steel Bronze

Illustration r.h., outside viewhanding details, see page 11.


6507 xx xx = 65 (r.h.) or 75 (l.h.) Ø 35 mm

Aluminum Stainless Steel Bronze

Illustration r.h., outside viewhanding details, see page 11.






15

A Ø 30

150

Ø 35

80

6514 Stainless Steel


Item nos. Ø A

6514 38 30 350 6514 45 30 450





16

350 570

80

40

35

110

44,5

6526 Aluminum Stainless Steel (brackets Aluminum)

With the publication of its 02/03Manual, FSB supplemented itsproven and long-successful in-line pull series in aluminum andstainless steel with a particularlysafe-to-grip design featuringheavily offset fixing points onwhich the ends of brackets areincorporated into the pull sec-tion. The in-line pull sectionsare supplied with a diameter of35 mm in either aluminum orstainless steel. The brackets aremade of aluminum and anodizedin the metal’s natural color.

The standard version has anA dimension of 350 mm and alength of 570 mm. Other center-to-center dimensions andlengths are possible.




17

6526 99 Ø 35 mm

To order custom designs in thepull handle series 6526, pleaseuse a copy of this page:

First specify the model desi redciting the applicable order codeabove. Then enter the quantityrequired and overall length inthe table below. Then enter de-tails of the distances betweenbrackets and, where applicable,their distance from the end ofthe handle in mm.

To ensure stability, the distancebetween brackets should notexceed 1,200 mm.

L

R1

R2

A1

L

R1

R2

A1

A2 L

R1

R2

A1

A2

A3

Qte. Overall length Distance between brackets Edge spacing* Fixing method L A1 A2 A3 R1 R2

*least. 40 mm max. 350 mm



18

114

300

83

35

125

300

35

88

6533 Aluminum Stainless Steel Bronze


The flattened oval pull handleseries 6533, 6534, 6535 and6536 see FSB’s philosophy ofthe ovally gripping hand and thediagonal moving arm put to effect in telling manner.

The circular fastening sectionhas been shortened and the griptilted towards the user by dint ofa flattened oval cross-section.The hand therefore enjoys opti-mum clearance whilst, stylisti-cally, these airy, elegant handlesdisplay a de cidedly architecturaldimension.

Guaranteeing FSB’s usual pro-duction excellence are the traditional casting technique foraluminum and an innovative internal high-pressure metalforming process for the stain-less steel variant.


19

300

116

35

83

122

300

87

35







20

450

133

39

98

6537 Stainless Steel Bronze

Door pulls 6537 are visually related to the 300 mm range of pulls.





21

450

117

39

89

6538 Stainless Steel Bronze

Door pulls 6538 are visually related to the 300 mm range of pulls.

If selecting stainless steel, thispull is available up to 1400 mmin total length by simply adding99 after 6538 and your length(L) in parenthesize. Example: 6538 99 (L = 40").




35 80

35

600

6541 Stainless Steel (grip)Aluminum (corners)

Matches FSB lever handle model 1077.

Safety clearance 51 mm

Pull Handles

22

35 75

35

600








23




C

D

A Ø


Matches FSB lever handle models 1107/1108.

Item nos. Ø A C D S

6542 3095 30 × 15 300 60 35 48 6542 6095 40 × 28 600 75 45 53

S = Safety clearance

35

81

Ø 30350



Available length up to 1200 mm



Pull Handles

24



400

25

25 65 6543 Aluminum Stainless Steel




Pull Handles

25


25 85

300500

6599 0036 Stainless Steel





26

A

C

D

Ø

R

6602 38 Aluminum Stainless Steel Bronze (only 6602 38) Brass Aluminum + Color


Fixing Ø = 20 mm M6 Ø ≥ 25 mm M8

Item-nos. Ø R A C D S

6627 34 20 25 200 75 30 456670 34 25 40 200 80 35 48

6670 37 25 40 300 80 35 48

6670 38 25 40 350 80 35 486602 38 30 55 350 90 35 516603 38 35 60 350 95 45 566604 38 40 60 350 105 45 65

6670 99* 25 40 200 –1200 80 35 486602 99* 30 55 300 –1200 90 35 516603 99* 35 60 300 –1200 95 45 566604 99* 40 60 350 –1200 105 45 65

S = Safety clearance * = Simply specify the desired CTC in parenthesize after

the product code. Example: 6670 99 (500 CTC)





27

R2

A Ø

R1

B

35

80

6605 Aluminum Stainless Steel Brass Aluminum + Color


Item nos. Ø R1 R2 A B

6605 25 25 260 40 250 32 6605 38 25 260 40 350 68 6605 50 25 400 40 500 88





28

30

210

70

25

6610 Aluminum Stainless Steel



6611 xx xx = 24 (r.h.) or 25 (l.h.)

AluminumStainless Steel



Illustration r.h., outside view, handing details, see page 11.


30

210

7022

55




29

30

210

7022

105 6612 Aluminum Stainless Steel






30

210

7022

90°

94



30

40

A L

77

112

20


In door pull series FSB 6615 (Ø 30 mm), fixing is by meansof laterally offset strap-typebrackets. The fastening andgripping sides are separatedfrom one another and henceprotect hands. The innovativecombination of fixing strap andpull lends the design an airy, vivacious appearance.

Item nos. Ø A L

6615 35 30 350 550 6615 45 30 450 650 6615 99* 30 451– 2100

* = Simply specify the desired CTC in parenthesize after the product code. Example: 6615 99 (500 CTC)




31

40

20

LA

118

83


In door pull series FSB 6616 (Ø 40 × 28 mm), fixing is bymeans of laterally offset strap-type brackets. The fasteningand gripping sides are separat-ed from one another and henceprotect hands. The innovativecombination of fixing strap andpull lends the design an airy, vivacious appearance.

Item nos. Ø A L

6616 35 40 × 28 350 550 6616 45 40 × 28 450 650 6616 99* 40 × 28 451– 2100




57

A2

A1 600 450

A3

75

57

75

75

75

Ø 25

Ø 25

62,5

Ø 45



32

6620 Ø 25 mm

Stainless Steel

Overall length 600 mm.

Item nos. Ø A1 A2 A3 Length Ending

6620 45 25 450 n/a n/a 600 mm 75 mm 6620 99* 25 X X X X 75 mm

* For customized lengths with multiple brackets, please provide dimensions for A1, A2 and/or A3. For example: 6620 99 (A1 = 400, A2 = 400, A3 = 400).

The stiles on glass doors havebecome narrower in recent years.FSB has responded by producinga filigree handle se ries in stain-less steel (Ø 25 mm). The straightbar handle features a clearancebetween the fixing center andthe center of the bar of no lessthan 57 mm.

With the curved version, theclearance is a mighty 130 mm.Both are supplied as standardwith an A dimension of 450 mmand an overall length of600 mm. Optionally, they canboth ex tend over the entire door.The standard measurement forthe end sections is 75 mm.

FSB recommends a distancebetween brackets of at most1,200 mm.

A2

A1= 450 600 450

A3

75

75

75

75

Ø 25

Ø 25

62,5

Ø 45

130

130

R 180 R 180

R 120

R 120


33

6621 Ø 25 mm

Stainless Steel

A1= 450 mm Overall length 600 mm.

Item nos. Ø A1 A2 A3 Length Ending

6621 45 25 450 n/a n/a 600 mm 75 mm 6621 99* 25 450 X X X 75 mm

* For customized lengths with multiple brackets, please provide dimensions for A2 and/or A3. For example: 6621 99 (A2 = 400, A3 = 400).




34

Ø 35

150400

80

60

Ø 30

Ø 35

150400

80

Ø 30

6681 00Ø 30 mm

Aluminum Stainless SteelBronze

Standard length 400 mm (also available in custom designs,see fax form next page).


6630 00Ø 30 mm

Stainless Steel


Fixing M8


Pulls above provided with stan-dard cap below.

.. 00 Back-to-Back Fixing Through-Bolted Fixing Concealed Fixing With Expansion Plug




35

L

R1

R2

A1

L

R1

R2

A1

A2 L

R1

R2

A1

A2

A3

6529 99 6630 996531 996532 99

6580 996681 996582 996583 99

To order custom designs in thepull handle series 6630 or 6681,please use a copy of this page: · First specify the model desired

citing the applicable ordercode above.

· Then enter the quantity re-quired and overall length inthe table below.

· Then enter details of thedistances between bracketsand, where applicable, theirdistance from the end of thehandle in mm.

· To ensure stability, the distancebetween brackets should notexceed 1,200 mm.

· Finally, please pick the cap required for standard versionswith a diameter of 30 Ø.

Ø 25 mm

Ø 30 mm

Ø 35 mm

Ø 40 mm

Ø 25 mm

Ø 30 mm

Ø 35 mm

Ø 40 mm

Qty. Overall length Optional Caps Distance between brackets Edge spacing* Fixing method L .. 00 .. 10 .. 20 A1 A2 A3 R1 R2

* least. 30 mm max. 350 mm

The custom designs in the pullhandle series 6630 and 6681can be supplied with two cus-tom caps, one a shallow curva-ture (10), the other a steppedflat cap (20).

.. 10 .. 20


36

A

85


Door pull design FSB 6635 was the first member of the oval family. A hefty oval tube (Ø 40 × 28 mm) was requiredto be ergo nomically designed toen sure hands could grip safelyand purposefully. This objectivewas achieved by welding handleand brackets together in amitre-joint. The upshot was adesign in stark contrast to thegentle curves of its tubularcounterparts. The market wasimmediately receptive.

Item nos. Ø A

6635 38 40 × 28 350 6635 45 40 × 28 450 6635 99* 40 × 28 451– 2100


When locating the fixing points,especially on narrow stiles ofglass doors, please note the off-center location of the thread edholes from the center of thecontact plane of the handle.The measurement’s differenceis exactly 6 mm, in the case ofFSB 6635. For detailed information onfixing, please turn to page 65.

6

Ø 40



37

A

92 90 6636 Stainless Steel

Door pull design FSB 6636 is avariation on the now classic firstdesign FSB 6635. The visualseverity of the first model is softened by having the bracketsslope towards the grip. The angle between the two is 135°.The new design qualities reallycome into their own given shorterlengths.

Item nos. Ø A

6636 38 40 × 28 350 6636 45 40 × 28 450 6636 99* 40 × 28 451– 2100


When locating the fixing points,especially on narrow stiles ofglass doors, please note the off-center location of the thread edholes from the center of thecontact plane of the handle.The measurement’s differenceis exactly 4 mm, in the case ofFSB 6636. For detailed information onfixing, please turn to page 65.

Ø 40 4

4



38

36

150400

25

71

Ø 30

36

150400

36

70

Ø 30

50

6642 Ø 30 mm

Brackets Aluminum

Grip Aluminum or Stainless Steel



6643 Ø 30 mm

Brackets Aluminum

Grip Aluminum or Stainless Steel


Fixing M6

For detailed information on fixing of the pull handles 6642 and 6643, please turn to page 72.


Fax Copy

39

6642 99 Ø 30 mm

6643 99 Ø 30 mm

To order custom designs in thepull handle series 6642 or6643, please use a copy of thispage: · First specify the model desi red

citing the applicable ordercode above.

· Then enter the quantity re-quired and overall length inthe table below.

· Then enter details of the distances between bracketsand, where applicable, theirdistance from the end of thehandle in mm.

· To ensure stability, the dis-tance between bracketsshould not exceed 1200 mm.

L

R1

R2

A1

L

R1

R2

A1

A2 L

R1

R2

A1

A2

A3

Qte. Overall length Distance between brackets Edge spacing* Fixing method L A1 A2 A3 R1 R2

*least. 40 mm max. 350 mm


40

350

80

Ø 35

30


FSB could not resist squeezingall the experience gained infashioning the 40 × 28 mm ovaltube into a smaller diameter.And thus it was that the standardin-line pull FSB 6650 came intobeing .It features a skewed ovalgrip 36 by 22 mm in diameteraffixed to circular brackets.

If so desired, FSB 6650 canalso be supplied in other lengths.


Item nos. Ø A

6650 38 36 × 22 350 6650 99* 36 × 22 351–1500






41

Ø 35

350

8030

175

R 175


Handle models FSB 6650 (inline), FSB 6682 (U-shape),FSB 6652 (semicircular) andFSB 6685 (triangular) are livingproof that tested designs featur-ing new oval cross-sectionshave the edge over their roundcounterparts both optically andin terms of gripping ergonomics.The hand glides effortlesslyaround them.






42

350

175

Ø 30

R 175

80

6653 Ø 30 mm

Stainless Steel






43

350

193,5

16,5

Ø 35

75

6655 Ø 35 mm







44

A

B

Ø

D

C

R

R

6662 Aluminum Stainless Steel Brass Aluminum + Color


Items-nos. Ø R A B C D S

6660 34 20 25 200 100 75 30 41 6661 34 25 40 200 100 80 35 42

6661 37 25 40 300 100 80 35 42

6661 38 25 40 350 100 80 35 42 6662 38 30 55 350 140 90 35 43 6663 38 35 60 350 140 95 45 45 6664 38 40 60 350 150 120 45 52

6661 99* 25 40 200 –1200 100 80 35 42 6662 99* 30 55 300 –1200 140 90 35 43 6663 99* 35 60 300 –1200 140 95 45 45 6664 99* 40 60 350 –1200 150 120 45 52



For detailed information onfixing, please turn to pages 66,67 and 68.




45

A

D

Ø

C 6669 Stainless Steel Bronze (only 6669 38 and 6669 99with available length up to1200 mm)


Fixing M8

Items nos. Ø A C D S

6606 38 25 350 75 35 50 6669 38 30 350 80 35 55 6669 99* 30 special length 80 35 556607 38 35 350 85 45 57 6609 38 40 350 90 45 60 6609 99* 40 special length 90 45 60







46

40

A L

77

20

B

R 6674 Stainless Steel

Door pull FSB 6674 takes theoffset strap-type brackets fromthe FSB 6615 series and fusesthese with the sweep of thecrescent-shaped round pull (Ø 30 mm).

This pull series is only sup-plied with A dimensions of 210 mm and 350 mm.

Items nos. Ø R A B L

6674 21 30 485 210 126 497 6674 35 30 1420 350 123 742




47

40

20

LA

B

83

R 6675 Stainless Steel

Door pull FSB 6675 takes theoffset strap-type brackets fromthe FSB 6616 series and fusesthese with the sweep of thecrescent-shaped oval pull (Ø 40 × 28 mm).

This pull series is only sup-plied with A Dimensions of 210 mm and 350 mm.

Items nos. Ø R A B L

6675 21 40 × 28 485 210 132 504 6675 35 40 × 28 1420 350 129 745




48

RA

B

D

C

90°

Ø

R

6679 Aluminum Stainless Steel BrassAluminum + Color


Items-nos. Ø R A B C D S

6649 34 20 25 200 90 75 30 416679 34 25 40 200 83 80 35 42

6679 37 25 40 300 133 80 35 42

6679 38 25 40 350 158 80 35 426623 38 30 55 350 152 90 35 436624 38 35 60 350 150 95 45 456625 38 40 60 350 150 105 45 49


For detailed information onfixing, please turn to pages 66, 67 and 68.




49

A

B

D

C

Ø

R2

R1

6683 Aluminum Stainless Steel Bronze (only 6683 38)BrassAluminum + Color


Items-nos. Ø R1 R2 A B C D S

6626 34 20 100 25 200 130 75 30 416673 34 25 100 40 200 140 80 35 42

6673 37 25 150 40 300 190 80 35 42

6673 38 25 175 40 350 215 80 35 426683 38 30 175 55 350 230 90 35 436659 38 35 175 60 350 235 95 45 456678 38 40 175 60 350 235 120 45 52


For detailed information onfixing, please turn to pages 66, 67 and 68.




50

35

350

8030

125

R 55


Door handle FSB 6682 is the U-shaped design in handle series 6650 (inline, ref. to page40), 6652 (semicircular, ref. topage 41) and 6685 (triangular,besides).

In all four cases, the easy-gripoval tube with a diameter of 36 × 22 mm is supported onround fixing brackets.






51

35

350

8030

152

90° R 55


The triangular tubular pull be-came a top-seller, echoing as itdoes the diagonal trussing socommonly to be found on frontdoors. The oval- section pullhandle 6685 adds ergonomicallyenhanced gripping qualities towhat are already very fine visuals.






52

200

100

80Ø 25

6677 00 Ø 25 mm

Stainless Steel


200

100 200

80Ø 25

6688 00 Ø 25 mm

Stainless Steel





Pull Handles Wave

53

R 800

A

Door width

Width of frame

Illustration l.h. Illustration r.h.

Ø 30

R 800

6510 30 mm Ø


Safety clearance 65 mm for 30 mm handle projection, fixing M8.




The wave handle is offered inaluminum, stainless steel andbrass with the following specifi-cations:

Torsion radius: 800 mm Handle diameter: 30 mm Bracket diameter: 35 mm

For quoting purposes, we requirethe following details togetherwith a dimensioned sketch:

1. Width of door 2. Size A required 3. Frame widths 4. Profile section 5. In case of glass doors:

distance of fixing holes from edge


54


The stainless steel pull handledesigns shown here are intendedas creative aids for architects,planners, designers, retailersand builder clients alike.

Please always give details ofthe door’s type, material andweight. We must have accuratedrawings before we can supplyquotes or implement orders.

a b c

d e f

Push and Pull Pad Handles

55

180

17,5

100

55

51

35

35

160

10

6

6108 Fixing M8

Available in:

Bracket: AluminumPad: Aluminum

Bracket: Aluminum Pad : Stainless Steel

The round M8 fixing sets aresuitable for these pad handles.For details page 66. Fixing accessories are shown in“Components” section.

119

145100

38

19

68

106

255210

38

19

68

6112 Aluminum

Fixing M6

6113 Aluminum

Fixing M6


56

For detailed information on fixing, please turn to page 72,fixing accessories are shown in“Components” section.


57

A S

30

11

10

50

21

150

15090 70

50

30

11

18

171

6181 62 Aluminum

Pad 150 × 150 mm Dimension A 90 mm c:c screw holes 70 mm

6181 70 Aluminum

Pad 180 × 180 mm Dimension A 120 mm c:c screw holes 100 mm

6181 74 Aluminum

Pad 200 3 200 mm Dimension A 120 mm c:c screw holes 100 mm

6184 62 Aluminum

Plastic-Pad, black

Fixing accessories are shown in“Components” section.

Screw hole Ø 8.5 mm

150

15090 70

38,5

11

18,5

165

25

17590 70

50

11

198

25

25




58

Fixing accessories are shown in“Components” section.

Screw hole Ø 8.5 mm

Pull Handles

59

2160 Aluminum

3601 Aluminum

3602 Aluminum

165140 113

52

25

Ø 16

200

45 64

160

45 59

Pull Handles

60

230200

25

55

50

175150

20

45

40

4023

175

3523

150

3603 Aluminum

3604 Aluminum

3617 Aluminum

3618 Aluminum

Pull Handles

61

210

6455

Ø 20

300210

59

Ø 20

80

300

80 2


Fittings feature two fixing pointsconcealed by a clip-on cover


Boreholes for 4.0 mm counter-sunk screws


counterplate to 6629

Boreholes for 4.0 mm counter-sunk screws

Double-action swing doors in restaurants, canteens, hospitalsand so forth are generally fittedwith both push and pull platesfor added protection.

An alternative arrangement isconceivable in the grippingarea, however. Furnishing thetwo faces of the door with thecombination shown above allows the desired direction ofswing to be implied.

FSB’s Threaded Insert Fixing Method

62

The self-tapping thread createsan excellent bond with compar-atively little play between doorstile and threaded insert, thusensuring an even and effectivefrictional connection – assumingthe accurate drilling of 12.5 mm- diameter borehole has beenmade.

Step One

Whether a manual or a powerdrill is used, threaded insertsrequire holes 12.5 mm in diameter to be drilled.

Step Two

Then the threaded insert isscrewed in using a size 8 Allenkey until the washer at the endof the threaded insert lies flushagainst the stile. FSB recommends an Allen keywith handle, as this is the bestway of guaranteeing the requi-site force is exerted.

Step Four

The handle is then placed onthe projecting “mounting post”.

Step Three

The “mounting post” is screwedinto the threaded insert.

FSB’s threaded insert method isa practically-minded and, at thesame time, enhanced means offixing concealed pulls to soliddoors, and in the process allow-ing distension forces to be ab-sorbed far more effectively bythe door stile.

Regardless of door thickness or stile type, a single type ofthreaded insert 34 mm long isused.


63

All door pulls with round necksare supplied as female partswith an internal left-handedthread 18 × 1.5 mm (M8 fixing)or 14 × 1.5 mm (M6 fixing). A clamping rose fastening com-prises a plastic washer, a steelwasher, a clamping element(with “lock-tight”), a rotatingrose and a spacer sleeve thatare securely held in place by aplastic clip and pre-attached tothe end of the handle.


The new FSB clamping rosefastening allows all FSB doorpulls with round necks to bescrewed tight against thesurface of the door by means ofan easy-to-operate clampingrose. Radial play allowed for byFSB ensures the necessarytolerances during fitting.Assembly is as follows:

Step One

First install the “mounting post”.How this is done depends onwhich fixing method you are using (back-to-back fixing,through-bolted fixing or con-cealed fixing).

Step Two

Then detach the clamping ele-ments from the end of the pullby turning them counterclock-wise. Remove the plastic clipand slip the plastic washer, thesteel washer, the clamping roseand the clamping element overthe mounting post in that order.Using the spacer sleeve, screwthe elements together, ensuringthat the clamping rose andclamping element remain freeto rotate.

Step Three

Place the handle on the fixingpoints and tighten against thedoor by alternately turning theclamping roses in a clockwisedirection.

A turning device for the FSBclamping rose is supplied withthe product.

mounting post

plastic washer

steel washer

clamping rose

clamping element

spacer sleeve

The FSB clamping rose fasteningis a new method of assemblingdoor-pulls whereby the pull istightened fast against the sur-face of the door. Visible fixingscrews are done away with.

Borehole Dimensions

64

Glass door Wood door Metal door

The illustrations below providethe bore hole dimensions for allFSB pulls based on type of doorand fixing method.

Fixing method

13

Inside

Outside

13

Inside

Outside

13

Inside

Outside

18

Inside

Outside

18

13

15

Outside

Inside

45

12,5

Outside

Inside

18

13

Outside

Inside

13

Outside

Inside

min. 30

Back-to-Back Fixing

Through-Bolted Fixing

Concealed Fixing With Expansion Plug


Fixing MethodsPull Handles

65

Pull handle series

66356636

Fixing accessories Fixing method

When selecting and orderingpull handles, please note thatthe pulls in this series are pro-duced as threaded-part andthrough-bolted fixing sections.

Item nos.

Back-to-Back Fixing



2 each socket head cup screws M8

4 each plastic washers 2 each lids stainless steel

Borehole Ø 13 mm

0582 1008 glass door 8 –10 mm

0582 3038 38 – 44 mm0582 3045 45 – 49 mm0582 3050 50 – 54 mm0582 3055 55 – 59 mm0582 3060 60 – 64 mm0582 3065 65 – 69 mm0582 3070 70 – 74 mm0582 3075 75 – 79 mm0582 3080 80 – 84 mm

2 each countersunk screw M8 4 each plastic washers2 each fixing washers

with capsstainless steel

Borehole Ø 13 mm

0582 2008 glass door 8 –10 mm

0582 4038 38 – 44 mm0582 4045 45 – 49 mm0582 4050 50 – 54 mm0582 4055 55 – 59 mm0582 4060 60 – 64 mm0582 4065 65 – 69 mm0582 4070 70 – 74 mm0582 4075 75 – 79 mm0582 4080 80 – 84 mm

2 each socket head cup screws M8

2 each plastic washers2 each expansion plugs

brass dull nickel finish 2 each lids stainless steel

Borehole Ø 12.5 mm (wood doors), Ø 13 mm (metal doors)

0582 0335 length of dowel 34 mm

Back-to-Back Fixing



66

Pull handle series round M8

6108, 6501, 6504, 6506, 6507,6510, 6514, 6529, 6531, 6532,6533, 6534, 6535, 6536, 6537,6538, 6540, 6541, 6542, 6546,6580, 6582, 6583*, 6602, 6603,6604, 6605, 6606,


6607, 6609, 6623, 6624, 6625,6630, 6650, 6652, 6653, 6655,6659, 6661, 6662, 6663, 6664,6669, 6670, 6673, 6677, 6678,6679, 6681, 6682, 6683, 6685,6688

Item nos.

2 each set screws M8

Borehole Ø 13 mm

0580 1008 glass door 8 – 10 mm

0580 3035 35 – 54 mm 0580 3055 55 – 74 mm 0580 3075 75 – 94 mm

2 each set screws M8 2 each fixing nuts with caps

Borehole Ø 13/18 mm, please turn to page 64

Grip diameter 25/30 mm

0580 2308 glass door 8 – 10 mm

0580 4335 35 – 44 mm0580 4345 45 – 54 mm 0580 4355 55 – 64 mm 0580 4365 65 – 74 mm 0580 4375 75 – 84 mm


0580 2408 glass door 8 – 10 mm

0580 4435 35 – 44 mm0580 4445 45 – 54 mm 0580 4455 55 – 64 mm 0580 4465 65 – 74 mm 0580 4475 75 – 84 mm


67




6108, 6501, 6504, 6506, 6507,6510, 6514, 6529, 6531, 6532,6533, 6534, 6535, 6536, 6537,6538, 6540, 6541, 6542, 6546,6580, 6582, 6583*, 6602, 6603,6604, 6605, 6606,


6607, 6609, 6623, 6624, 6625,6630, 6650, 6652, 6653, 6655,6659, 6661, 6662, 6663, 6664,6669, 6670, 6673, 6677, 6678,6679, 6681, 6682, 6683, 6685,6688

Item nos.

2 each set screws M8 2 each expansion plugs brass

dull nickel finish



1 plastic washer 1 clamp

Borehole Ø 13 mm

0580 9002 2 – 15 mm 0580 9016 16 – 30 mm


68


3684, 3688, 6610, 6611, 6612,6613, 6626, 6627, 6642, 6643,6649, 6660

Fixing accessories Fixing method Item nos.

Back-to-Back Fixing





Borehole Ø 13 mm

0580 1208 glass door 8 – 10 mm

0580 3235 35 – 54 mm 0580 3255 55 – 74 mm 0580 3275 75 – 94 mm




0580 2208 glass door 8 – 10 mm

0580 4235 35 – 44 mm0580 4245 45 – 54 mm 0580 4255 55 – 64 mm0580 4265 65 – 74 mm0580 4275 75 – 84 mm

2 each set screws M6 2 each expansion plugs brass

dull nickel finish



1 plastic washer 1 clamp

Borehole Ø 13 mm

0580 9202 2 – 15 mm 0580 9216 16 – 30 mm


69

Pull handle series

6615 6616 6674 6675


Back-to-Back Fixing



2 each countersunk screws M8with sleeve nuts M8stainless steel

4 each plastic washers

Borehole Ø 13 mm

0583 1008 glass door 8 – 10 mm

0583 3034 34 – 43 mm0583 3044 44 – 53 mm 0583 3054 54 – 63 mm 0583 3064 64 – 73 mm 0583 3074 74 – 83 mm

2 each countersunk screws M8with sleeve nuts M8stainless steel

2 each washersstainless Steel


Borehole Ø 13 mm

0583 2008 glass door 8 – 10 mm

0583 4036 36 – 45 mm0583 4046 46 – 55 mm0583 4056 56 – 65 mm0583 4066 66 – 75 mm0583 4076 76 – 85 mm

2 each countersunk screws M8stainless steel

2 each expansion plugs brass dull nickel finish





70

Pull handle series

6620 6621


Back-to-Back Fixing



2 each countersunk screw M8with sleeve nuts M8stainless steel


Borehole Ø 13 mm

0584 1008 glass door 8– 10 mm

0584 3035 35 – 44 mm0584 3045 45 – 54 mm 0584 3055 55 – 64 mm 0584 3065 65 – 74 mm 0584 3075 75 – 84 mm

2 each countersunk screw M8with sleeve nuts M8stainless steel

2 each washers stainless steel


Borehole Ø 13 mm

0584 2008 glass door 8 – 10 mm

0584 4035 35 – 44 mm0584 4045 45 – 55 mm 0584 4055 55 – 65 mm 0584 4065 65 – 75 mm 0584 4075 75 – 85 mm

2 each countersunk screw M8stainless steel

2 each expansion plugs brass dull nickel finish





71

Pull handle series

6526


Back-to-Back Fixing




Borehole Ø 13 mm

0587 1008 glass door 8 – 10 mm

0587 3035 35 – 54 mm 0587 3055 55 – 74 mm 0587 3075 75 – 94 mm



0587 2308 glass door 8 – 10 mm

0587 4335 35 – 44 mm0587 4345 45 – 54 mm 0587 4355 55 – 64 mm 0587 4365 65 – 74 mm 0587 4375 75 – 84 mm

2 each set screws M8 2 each expansion plugs

brass dull nickel finish




72

Pull handle series

6112, 61136543, 6599 0036 6642, 6643


Back-to-Back Fixing




Borehole Ø 13 mm

0580 1208 glass door 8 – 10 mm

0580 3235 35 – 54 mm 0580 3255 55 – 74 mm 0580 3275 75 – 94 mm


Borehole Ø 13/18 mm, look page 64

0580 2208 glass door 8 – 10 mm

0580 4235 35 – 44 mm0580 4245 45 – 54 mm 0580 4255 55 – 64 mm0580 4265 65 – 74 mm0580 4275 75 – 84 mm

2 each set screws M6 2 each expansion plugs

brass dull nickel finish



Overview

73

Page 74

4220 41/51

Page 74

4220 42/52

Page 76

4223 41/51

Page 76

4223 42/52

Page 78

4224 42/52

Page 75

4220 45/55

Page 77

4223 45/55

Page 78

4224 45/55

Page 79

8812

Page 89

2339 07

Page 92

4230

Page 88

2302 07

Page 88

2322 07

Page 88

2329 07

Page 89

2374 07

Page 91

3684

Page 92

3686

Page 91

3688

Page 90

4299 00xx

Page 90

4299 00xx

Page 82

4228

Page 93

8820

Page 95

8821

Base Material

Aluminum

Stainless Steel

Bronze

Brass


Glass Door Trim

74

4220 41 r.h.

4220 51 l. h.


Rectangular lockset plate withcover plates with heavy-duty glass door lock(DIN 18251, analogous to Class 4) designed for use with PZ cylinder CTC 72 mm

4220 42 r.h.

4220 52 l. h.


Rectangular lockset plate withcover plates with heavy-duty glass door lock (DIN 18251, Class 4) designed for use with PZ cylinder CTC 72 mm

184

68

72

20,5

81 10

96

21,5

56,5

8

shown here European (DIN) r.h.

Technical notes:

Dimensions given assume glass8 mm thick. Lockset plates forglass doors are prepared at thefactory for glass 8 mm, 10 mmand 12 mm thick. For further technical notes referto pages 80–85.

The handle shown is illustrative.Virtually any other FSB handlecould be used instead.

Handles, strikes, and PZ cylin-der must be ordered seperately.

On versions 4220 42 and 4220 52 roses must also be ordered separately.

Options:

· Passage · Privacy (with or without indi -

cator): Please indicate whenordering, as trim is fitted withthumbturn and indicator(1735 0054) as standard.

Strike Box for Twin-leaf Glass Doors

75

4220 45 r.h.

4220 55 l. h.


Rectangular strike box to suitlockset plates for glass doors4220 41/51 and 4220 42/52.

The strike must be ordered in

the hand opposite of the lock.

184

96

111 10

21,5

8

shown here European (DIN) l.h.

68

72

81

56,5

184

96

111

96

10

21,5

8

Technical notes:

Dimensions given assume glass8 mm thick. Strike boxes areprepared at the factory for glass8 mm, 10 mm and 12 mm thick.

Glass Door Trim

76

4223 41 r.h.

4223 51 l. h.


Rectangular lockset platerounded corners with cover plates with heavy-duty glass door lock(DIN 18251, Class 4) designed for use with PZ cylinder CTC 72 mm

4223 42 r.h.

4223 52 l. h.


Rectangular lockset platerounded corners with cover plates with heavy-duty glass door lock (DIN 18251, Class 4) designed for use with PZ cylinder CTC 72 mm

184

68

72

20,5

81

96

56,5

10

21,5

8

Technical notes:

Dimensions given assume glass8 mm thick. Lockset plates forglass doors are prepared at thefactory for glass 8 mm, 10 mmand 12 mm thick. For further technical notes referto pages 80–85.

The handle shown is illustrative.Virtually any other FSB handlecould be used instead.

Handles, strikes, and PZ cylin-der must be ordered seperately.

On versions 4223 42 and 4223 52 roses must also be ordered separately.

Options:



shown here European (DIN) r.h.

77

Strike Box for Twin-leaf Glass Doors

4223 45 r.h.

4223 55 l. h.


Rectangular strike box roundedcorners to suit lockset plates forglass doors 4223 41/51 and4223 42/52.



184

96

111 10

21,5

8

68

72

81

96

56,5

184

111

96

10

21,5

8

Technical notes:

Dimensions given assume glass8 mm thick. Strike boxes areprepared at the factory for glass8 mm, 10 mm and 12 mm thick.

shown here European (DIN) l.h.

78

Glass Door Trim Compact Strike Box

4224 42 r.h.

4224 52 l. h.


Heavy-duty bearing Rectangular lockset plate com-pact with cover plates with heavy-duty glass door lock(DIN 18251, Class 4) designed for use with PZ cylinder CTC 72 mm 8 mm split follower cast-steel latch

drawings European (DIN) r.h.

Door frames that are not to theEuropean (DIN) specificationcan, of course, also be used –though the flush-frame effectcannot then be guaranteed. The trim can also be used inconjunction with partition systems.

The door’s transparency is un-derscored by the tight dimen-sions of the lock cover, which at170 mm by 89 mm is some10 % smaller than in standardglass door trim. This paring-down was achieved by develop-ing a special-purpose lock thatis every bit as rugged and func-tional as larger models as wellas being suitable for all sizes of glass door.

We have developed a specialheavy-duty bearing for high fre-quency transited doors involvingan expansion sleeve in Teflon-coated stainless steel that en-compasses the door handle over its entire bushingarea whilst also dependablywithstanding the mechanicalforces exerted on large-formatglass doors.

Technical notes:

Dimensions given assume glass8 mm thick. Lockset plates forglass doors are prepared at thefactory for glass 8 mm, 10 mmand 12 mm thick. Strike boxesare prepared at the works forglass 8 mm and 10 mm thick. Hardware for glass 12 mm thickis available to order.

For further technical notes referto pages 80–85.

The handle shown is illustrative.Virtually any other FSB handlecould be used instead. Handles,strikes, and PZ cylinder must beordered seperately.

Options:



4224 45 r.h.

4224 55 l. h.


Rectangular strike box compact

To suit lockset plate for glassdoors 4224



170

89

104

R 2

5,2

16,18

170

89

104

60

72

89

56,5

5,2

16,1

874

170

60

72

20,5

74 5,2

16,1

41,6

56,5

89

8

Shown 4224 52 DIN l.h. lock with 4224 45 DIN r.h. strike box

79

European Profile Cylinders (PZ)

8812 0064 Cylinder length 217⁄32" (64 mm)for 13⁄8"–13⁄4" door thickness including lock case

Key × Key


Key × Thumbturn


1⁄2" Cylinder Thumbturn only

1744 turnpiece

217⁄32"(64)

15⁄16"(33)

21⁄32"(17)

11⁄4"(32)A 11⁄4"

(32)B13⁄32"(10)

R15

11⁄4"(32)B

217⁄32"(64)

15⁄16"(33)

7⁄8"(22)

11⁄4"(32)A

11⁄2"(38)


Key × Thumbturn


1⁄2" Cylinder Thumbturn only

1709 turnpiece

11⁄4"(32)B

217⁄32"(64)

15⁄16"(33)

7⁄8"(22)

11⁄4"(32)A

11⁄32"(26)

B

19⁄16"(40)

15⁄16"(33)

7⁄8"(22)

A = 13⁄32"(10); B = 13⁄16"(30)

A

11⁄32"(26)

Please see specifics on pages84 and 85. These shorter cylin-ders would need to be procuredseparately.

For 8, 10 and 12 mm doorthickness.

FSB’s shortest cylinder is 64 mm.The 8812 0064 will work, butwill extend beyond the face ofthe plate an extra 4–7mm perside.

The ideal cylinder length forglass door locks is 50 or 55 mmdepending on the lock design.

Keyway “C-type” 5 pin on each side.Supplied keyed alike up to 20as standard. May be keyed differently or master keyed on request.

Keys Nickel plated brass, suppliedwith two keys per cylinder.

Cylinder Finish Nickel plated brass.

Thumbturn and Finishes · US 28 (matches FSB 0105)

Aluminum Natural Color Anodized

·US 32 D (matches FSB 6204)Satin Stainless Steel


B

19⁄16"(40)

15⁄16"(33)

7⁄8"(22)

A = 13⁄32"(10); B = 13⁄16"(30)

A

11⁄2"(38)

Lock and Strike Handing for Glass Doors

80

Glass Lock and

Strike Box Handing

Order Left Hand Lock

and Right Hand Strike Box

(Lock on the inside per picture above)

Order Right Hand Lock

and Left Hand Strike Box

(Lock on the inside per picture above)

Order Left Hand Lock

and Right Hand Strike Box

(Lock on the outside per picture above)

Order Right Hand Lock

and Left Hand Strike Box

(Lock on the outside per picture above)

Handing of Doors with

Surface Locks

Handing for Surface Locks

Important Notice: Handing forsurface mounted locks differs tothe handing for bored locks.

With surface mounted locksthere is no LHR and RHR func-tionality with the locks as thereis no bevel associated with thelock. Consequently, the locksare only ordered LH or RH.

Should the door need to ap-proach the frame in the oppos-ing direction, it is necessary tomount the lock on the oppositeside of the door.

See illustrations below to de-termine hand to be ordered.

LH – inward opening

inside

outside

RH – inward opening

inside

outside

LH – outward opening

inside

outside

inside

outside

RH – outward opening

Glass Door Locks Installation

81

slamming face opening face

shown here: 4220/4223 41 RH

shown here: 4220/4223 42 RH

Straight-Cornered Hinges for Glass Doors

82

4228 Satin chromium-plated Steel Stainless Steel

VARIANT glass door hinge insatin chromium-plated steel tosuit Aluminum, AluGrey® orStainless Steel finishes withhinge connector

To suit 4220 and 4224 Serieslockset plates for glass doors

18

45 95

42

74

27

HDL

HDL

HDL

HDL

4228 0101 VARIANT VXG 7990/100Kheavy-duty hinge for glass doorson rabbeted, wood, steel or alu-minum frames with three-dimensionally adjustable matingelements

4228 0102 VARIANT VNG 7990/100K heavy-duty hinge for glass doorson rabbeted steel frames withthree-dimensionally adjustablemating elements

4228 0103 VARIANT VG 8790K heavy-duty hinge for glass doorson rabbeted steel frames

4228 xx04 xx = 41 (r.h.) or 51 (l.h.) VARIANT VG 3990K heavy-duty hinge for glass doorson rabbeted wooden soffit andblockwood frames

Technical notes:

Loading capacity 60 kg

Glass door hinges prepared atthe factory for glass 8 mm and10 mm thick. For further technical notes see pages 86 and 87.

Door Dimensions acc. DIN 18101

83

Hinge datum line

Hinge datum line

834 for frame dimension 841

35,5

16

45

35,5

16

45

237214,5

1435

1435

57

50

80

960

1972

for

fram

e di

men

sion

198

3

Hinge datum line

Hinge datum line

834 for frame dimension 841

35,5

16

45

35,5

16

45

237232

1435

1435

57

50

80

960

1972

for

fram

e di

men

sion

198

3

T.D.I.U.S.* 750 × 2000 875 × 2000 1000 × 2000Frame rabbet dimensions 716 × 1983 841 × 1983 966 × 1983Standard glass dimensions 709 × 1972 843 × 1972 959 × 1972

T.D.I.U.S.* 750 × 2125 875 × 2125 1000 × 2125Frame rabbet dimensions 716 × 2108 841 × 2108 966 × 2108Standard glass dimensions 709 × 2097 834 × 2097 959 × 2097

* = theoretical dimensions in unfinished state

4228 01 | 4228 02 4228 03 | 4228 04

Technical Notes 4220 and 4223 Series

84

min.27,5

min.27,5

13

8

8

8

55

8

20,5 42

20,5 5439

39

26

20,539

Handle specification

Series 4220 41/51 and 422341/51 lockset plates for glassdoors require specially adaptedpairs of lever handles, one ofwhich has a truncated shank.

Our In-house Sales Service personnel implement this specification when orders aremade.

Bearings

Series 4220 42/52 and 422342/52 lockset plates for glassdoors may be fitted either withstandard bearings and pairs oflever handles, with or withoutroses, or with heavy-duty hard-ware having AGL® bearings androses.

Profile cylinder version

On aesthetic grounds, profilecylinders 27.5/27.5 mm longare recommended for all locksetplates for glass doors owing tothe comparatively short projec-tions involved.

Privacy version

All lockset plates for glass doorscan also be used in privacy trim.The 4220 and 4223 Seriesmodels can be fitted with anyindicator FSB supplies (please refer to “Lever, Knob and TrimDesigns” section).

Please order these separately;they are assembled on site. The hardware is suitable fordoors opening either inwards or outwards.

Order details required:

We do not supply our locksetplates for glass doors completewith handles. When orderinghandles, please specify that theyare for glass doors and 4220 or4223 Series hardware as well asadvising:

- the lever handle model required

- the type of hardware (standardor heavy-duty bearings)

- surface lock handing

The dimensions given assumeglass 8 mm thick. Locksetplates for glass doors are pre-pared at the works for glass 8 mm, 10 mm and 12 mmthick.

Technical Notes 4224 Series

85

8

8

8

9 50(54)

25 (27,5)

25 (27,5)

20,5 41,6

29,320,3

29,3 20,5

Handle specification

Series 4224 lockset plates forglass doors require speciallyadapted lever handle sets fea-turing a spindle projection thatdiffers from the FSB standard.

Our In-house Sales Service personnel implement this specification when orders aremade.

Bearings

The bearings used for the 4224Series take the form of heavy-duty Teflon-coated sleeves thatencompass the door handleover its entire bushing areawhilst also dependably with-standing the mechanical forcesexerted on large-format glassdoors.

There is no need to additionallyfit roses in heavy-duty bearings.

Profile cylinder version

On aesthetic grounds, profilecylinders either 25/25 mm or27.5/27.5 mm long are recom-mended for all lockset plates forglass doors owing to the com-paratively short projections in-volved.

Checks should be made on acase-by-case basis as towhether 25/25mm profile cylin-ders are fit to function in closingsystems.

Privacy version

Please specify indicating variantwhen ordering, since the trim isfitted with indicator 1735 0054(please refer to “Lever, Knob andTrim Designs” section) as stan-dard at the factory. The indica-tor is not assembled on site.

The hardware is suitable fordoors opening either inwards oroutwards.

Order details required:

We do not supply our locksetplates for glass doors completewith handles. When orderinghandles, please specify that theyare for glass doors and 4224Series hardware as well as advising:

- the lever handle model required

- surface lock handing

The dimensions given assumeglass 8 mm thick. Locksetplates for glass doors are pre-pared at the works for glass 8 mm and 10 mm thick. Hardware prepared for glass 12 mm thick can be obtainedon request.

Technical Notes for 4228

86

Bore hole Ø 16 mm

Hinge datum line

241214,5

4580

35,5

Bore hole Ø 16 mm

Hinge datum line

241214,5

4570

35,5

Bore hole Ø 16 mm

Hinge datum line

241 232

45

35,5

35

Bore hole Ø 16 mm

Hinge datum line

241 232

45

35,5

11,5

22

The positioning of hinge con-nectors relative to the hinge datum line also necessitatesadapting boreholes in the glassdoor. This should be borne inmind most notably in the casesof VX and VN commercial hinges.

Frame Connection Dimensions

87

HDL 28

2880

24

2470

HDL

30

17,5HDL

35

30

17,5

11,5

22

HDL

VARIANT commercial hinge forglass doors on rabbeted timber,steel or aluminium frames withthree-dimensionally adjustablemating elements VX

· suitable for wholly glazeddoors with standard verticalborehole layout

· for glass 8 and 10 mm thick · twistproof threaded stud · concealed, no-maintenance

axial-radial sliding bearings · combinable with mating

element: · for blockwork

frames VX 7601 3D

· for soffit frames VX 7602 3D

· for blockwork frames VX 7605 3D

· for steel frames VX 7611 3D

VX 7612 3D · for aluminium

frames VX 7621 3D · non-handed

VARIANT commercial hinge forglass doors on rabbeted steelframes with three-dimensionallyadjustable mating elements

· suitable for wholly glazeddoors with standard verticalborehole layou t

· for glass 8 and 10 mm thick· twistproof threaded stud · concealed, no-maintenance

axial-radial sliding bearings · combinable with mating ele-

ment VN 7608/120 3D · non-handed

VARIANT commercial hinge forglass doors on rabbeted steelframes


· for glass 8 and 10 mm thick · for mating elements V 8600

or V 8610 · non-handed

VARIANT commercial hinge forglass doors on rabbeted woodensoffit and blockwork frames


· for glass 8 and 10 mm thick · for mating elements of the

V 3600, V 3610, V 3630, V 3650 series and clampingblock V 3604 or V 3607

· necessary to indicate DIN handing

For further information onhinges, hinge connectors, framefastening elements etc., pleasecontact FSB.


88

X

50

45

52

Ø

52

2302 07 Aluminum (X = 77 mm) Stainless Steel (X = 73 mm) Bronze (X = 72 mm) Brass (X = 72 mm)

Borehole Ø 13 mm


Borehole Ø 13 mm

2329 07 Aluminum (Ø = 50 mm) Stainless Steel (Ø = 55 mm) Bronze (Ø = 55 mm)

Borehole Ø 13 mm

Deadknobs are generally fitteddirectly to glass doors. Thereare no locks involved.

The knobs are joined togetherat the assembly stage by meansof an 8 mm square spindle (fortwo female parts).


89

55

60

52

80

2339 07 Aluminum

Borehole Ø 13 mm

Design: Philippe Starck


Borehole Ø 13 mm

Design: Jasper Morrison

Deadknobs are generally fitteddirectly to glass doors. Thereare no locks involved.

The knobs are joined togetherat the assembly stage by meansof an 8 mm square spindle (fortwo female parts).

90

Flush Pulls for Glass Doors

4299 00xx xx = 12 (10 mm door thickness) xx = 19 (8 mm door thickness)

Stainless Steel

Flush pull for glass doors

100 74

1160

47

15

4299 00xx xx = 26 (10 mm door thickness) xx = 21 (8 mm door thickness)

Stainless Steel

Flush pull for glass doors

100 74

1160

47

15

91

Pulls for Glass Doors

3684 2114 Aluminum

Design: Ton Haas 210

30

70


Design: Christoph Ingenhoven 210

30

66

Back-to-back and through-bolted fixing, cf. Page 64

92

Sliding Door Handle Door Holder


Sliding door handle for fixing in pairs

Design: Jahn/Lykouria

168

3256

24 58

4230 xxxxStainless Steel

(A) (B)Items-nos. width thick ness

overall of glass

xxxx = 0000 27 mm 8 mm xxxx = 1000 29 mm 10 mm xxxx = 1200 31 mm 12 mm

40

B50

25

Ø 10A

93

Top Mounted System

The high quality stainless steelsliding door gear for glass doorsare the visible combination offunctionality and appealing design.

The system is suitable for wallas well as ceiling installationand therefore it is usable in various building situations.

Product features

· Due to the small dimensions of the carrier rollers there isenough mounting clearanceeven for low ceilings

· Track can be mounted to awall or ceiling

· Rail consists of full materialwith flat turned ends providedwith chamfers

· Door leaf holder with a diame-ter of 35 mm contributes to anoptimal clamping area

· The bottom roller is preciselyadjustable by an eccentricscrew. It consists of a plasticroller and can be adjusted tolie exactly under the rail. Thusthe roll characteristic of thesliding door can be adjustedindividually

· For every glass strength (ESG8/10/12 mm) there is a preci-sion-floor guide available. Itconsists of wear-free felt andtherefore it is extremly noise-less

· High quality plastic bearingsurfaces of the rollers for ex-treme quiet running with aminimum energy expenditure

Application range

· For sliding doors and elementsin interior and exterior areas

· For door leaf weights up to105 kg (231 lbs)

· For office as well as living areas

Installation drawing

Drawing-No. 10801-ep01 and 10801-ep02

Table glass strength ESG (toughened safety glass)

for wall mounting

Dim. 8 mm 10 mm 12 mm

A 13.0 mm 11.0 mm 9.0 mm B 7.5 mm 5.5 mm 3.5 mm C 24.0 mm 26.0 mm 28.0 mm

for ceiling mounting

Dim. 8 mm 10 mm 12 mm

A 24.0 mm 26.0 mm 28.0 mm B 33.5 mm 32.5 mm 31.5 mm

8820 Description ID No.

Set for wall mounting 119408

Set for ceiling mounting 122581

Floor guide, stainless steel

· for toughened safety glass 8 mm 121003



Projected solutions on request.

8820

94

Installation for wall mounting

Installation for ceiling mounting

Ø 25

100Recommendation

30

42.5Ø 50

70

20

566 150

17.5

min.75

50

60

51

Clear height

LH

20

Ø 16Ø 35

A

B

C

Glass thickness 8/10/12 mm

Floor guides made of stainless steel

Digging safety deviceadjustable via excenter screw

7

Ø 58.5

Ø 25

100Recommendation

30

42.5

70

20

150

120

50

60

110

Ø 16

89

± 4

Ø 35

A

B

7

566

Glass thickness 8/10/12 mm

Floor guides made of stainless steel

Digging safety deviceadjustable via excenter screw

34

M 8

Ø 40

Ø 58.5

Ø 40

Ø 20

95

Floor Mounted System

Product features

· High quality sliding door hard-ware combines aesthetics andfunction

· Guide rail can be mounted ona wall or ceiling allowing a flex-ibility installation

· The overall weight of the slid-ing door is carried by a trackon the floor, thereby a usage in

various building situations ispossible, e.g. in areas where asuspension can not be mounted

· High quality plastic bearingsurfaces of the rollers for extreme quiet running with aminimum energy expenditure

Application range

· For sliding doors and elementsin interior and exterior areas

· For door leaf weights up to135 kg (297 lbs)

· Application also with suspend-ed ceilings cause the overallweight of the sliding door iscarried by a track on the floor

· For living as well as office areas

8821 Description ID No.

Set for ceiling mounting, screwed 10 mm 121392 adhesive 10 mm 119409

Set for wall mounting, screwed 10 mm 123250

Projected solutions on request.

Visible rollers on floor mountedsemicircular 1⁄4"rail. The floorrail carries the door weight. Atthe top a u-shaped profileguides the door. Especially forareas where wall or ceilingmounting is not possible.

60

60

60

25

min. 40 min. 40 25

25

26

32

20 (± 3)21

Ø 6 × 60

20 (± 3) 10 20 (± 3)ca. 40

3

Ø 10

10

18

3

R 8

ca. 250

60ca. 250

ca. 4

ca. 11

6.5

Ø 16Ø 40

9 7

30Ø 69.5

Glass cutout

Rolls, adjustable via glass excenter screw± 1.5 mm

Stopper

Trackfixing with screws

or adhesive

3

Installation drawing

Drawing-No. 10801-ep03

96

Roller-guided Sliding Door Gears Product Information for Sliding

Door Gears

In accordance with the defini-tion of the liability of manufac-turers for their products set outin § 4 of the “Produkthaftungs-gesetz” (German Manufactur-er’s Liability Law), the followinginformation on sliding door gearshould be observed. Failure todo so absolves the manufactur-er from liability.

Product Information and Use

in Accordance with intended

Purpose

Sliding door gear, according tothis definition, are fittings fordoors and other push-able ele-ments, henceforth called objects,which are not normally movedfaster than walking pace. Slid-ing door gear is used in vertical-ly fitted doors made of wood,plastic, glass, aluminum or steeland appropriate combinationsof these materials. A floor guideis provided at the lower horizon-tal edge of the door. Special ver-sions of products must be spec-ified for damp rooms, directexposure to the elements, expo-sure to cross winds, for installa-tion near the sea and in highlycorrosive conditions.

Correct installation by quali-fied personnel is a particularlyimportant aspect of use for in-tended purpose. The objectmust be sufficiently rigid at allof these points. The function ofthe gear must not be hinderedor altered by installation. Abuffer must be used in order tolimit the displacement path.

Misuse

Misuse – in other words use in amanner not in accordance withthe intended purpose – can besaid to occur in the followingcases in particular:

· if the gear is used with a high-er max. load than specified inthe catalogue and in the otherproduct documents,

· if incorrectly installed or at-tached,

· if ambient temperatures aretoo high or too low,

· if particularly aggressive mediacan affect the gear,

· if subjected to inordinatelygreat pushing or pulling loads,

· if the position of the track de viates too greatly from thehorizontal,

· if foreign bodies get into thetrack,

· if the rollers are operated toofast,

· if alterations are carried outwithout the manufacturer’s authorization,

· if obstacles are placed in theopening or between the dooror the object thereby prevent-ing intended use,

· if additional loads act upon thedoor or object,

· if someone is trapped betweenthe door and the door framewhile the door is being pushedor closed, or if a person or partof the body is in this area.

Product Performance

In cases where the performanceof the product is not specificallydescribed in the catalogues,brochures, instructions etc.,special requirements must bediscussed with and agreed bythe manufacturer. Our regula-tions, which affect the composi-tion of the sliding door gear, arebinding.

Product Maintenance

Components of sliding door gearwhich are relevant to safety mustbe regulary inspected for properfixing and signs of wear. Fixingscrews are to be re-tightenedand faulty components must bereplaced. In addition, the follow-ing maintenance work must becarried out at least once a year:

· All moving parts are to be test-ed for free movement.

· In the case of running car-riages with metal rollers, themoving parts must be greased(type of grease to be used onrequest). Plastic rollers mustnot be greased.

· Only use cleaning agentswhich do not impair the anti-corrosion protection of thegear.

· Faulty sliding door gears mustbe replaced.

· Adjustment work on the gearsand the replacement must becarried out by qualified per-sonnel.

Duty of Information and

Instructions

The following sources of infor-mation are available to plan-ners, specialist dealers, admin-istrative personnel, buildingcontractors and users by way offulfillment of the duty of infor-mation and instruction:

· catalogues, brochures· quotations, descriptions of offer · mounting and installation

drawings, maintenance andoperation instructions.

In order to ensure correct use,proper functioning and mainte-nance and care of sliding doorgear,

· architects and planners mustrequest and apply the neces-sary product information,

· specialist dealers must takeaccount of the product infor-mation and notes in the pricelists, and in particular must re-quest all necessary instruc-tions and pass these on to theinstallation personnel,

· installation personnel musttake account of all product information, and in particularmust request operating andmaintenance instructions andpass these on to the orderingparty and the user.

Date post:	29-May-2018
Category:	Documents
Upload:	dangdung
View:	216 times
Download:	0 times

Door Pulls Pulls & Glass Door Hardware Hinges, Accessories ... ket’s first flush pulls with spring...

Documents